Scribd
Upload
66 views1 page

Nmea Signals Multiplexer Snmea6: Enamor Products Nmea Modules Family

SNMEA6 is a data multiplexer that can collect NMEA sentences from 6 inputs simultaneously at different baud rates and transmit them through a single output at a selected baud rate. It protects inputs through galvanic separation and verifies checksums. Additionally, the 6 ports can be configured as either inputs or outputs, and special programming allows for protocol filtering or translation.

Uploaded by

Radek
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
66 views1 page

Nmea Signals Multiplexer Snmea6: Enamor Products Nmea Modules Family

SNMEA6 is a data multiplexer that can collect NMEA sentences from 6 inputs simultaneously at different baud rates and transmit them through a single output at a selected baud rate. It protects inputs through galvanic separation and verifies checksums. Additionally, the 6 ports can be configured as either inputs or outputs, and special programming allows for protocol filtering or translation.

Uploaded by

Radek
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

ENAMOR PRODUCTS NMEA MODULES FAMILY

NMEA SIGNALS MULTIPLEXER SNMEA6

GENERAL FEATURES:
▪▪ Power supply: 24VDC (18-36VDC)
on demand (10-36VDC);
▪▪ Power consumption (max): 6W;
▪▪ Number of inputs: 6 RS422-ISO
(RX in input, TX if output);
▪▪ Number of outputs: 1 RS232
and 1 RS422 - 57600Bd;
▪▪ Compatibility: NMEA 0183 - Standard
for Interfacing Marine Electronic Devices;
▪▪ Baud rate: 4800, 9600, 14400, 19200, 38400, 56000,
57600, 115200 Bd;
▪▪ Checksum verification;
▪▪ Various additional special data conversion
features.

SNMEA6 data multiplexer can collect NMEA sentences received SNMEA6 can even work as splitter and multiplexer at the same
from 6 inputs at the same time (also with different baud rate) time. Arriving protocols are buffered and then retransmitted
and transmit it over single output with the seleted baud rate. to allow change of baud rate. Protocol is verified by check sum

SNMEA6 is receiving NMEA signal on its inputs and then the (if available) and if it doesn’t match - rejected. The sum of baud

signal goes through protection circuit. Then the signal is stored rate of every input must be less then baud rate of output.

in internal buffer and then resend over single output. All inputs In SNMEA6 multiplexer all ports are designed to half duplex
are separated galvanic from output and among each other. communication (only one way – TX or RX in one time), what

The power supply circuit is equipped with protecting fuse and causes that inputs/outputs RS422 also are described like

overvoltage protection and reversed polarity protection. DC/DC RS485.

converter is used to separate the working circuit galvanic from On special demand SNMEA6 can be programmed to filter
the power supply. protocols and even translate selected protocols to another

As additional feature SNMEA6 has possibility that all 6 inputs protocols. In this case please contact Enamor R&D department.

can be programmable as inputs/outputs. So because of that It is also possible to use multiplexer as standby switchover of
GPS receivers with special software installed.

ENAMOR LTD. 1 INŻYNIERSK A STREET 81-512 GDYNIA, POLAND

TEL. +48 58 69 01 700 FA X +48 58 69 01 701 EMAIL: [email protected] W W W.ENAMOR.PL

You might also like