SAUDIARAMCO.

NOTES:
LIST OF MATERIAL
1. ALL DIMENSIONS ARE IN MILLIMETER UNLESS
OTHERWISE SPECIFIED.
DWG. ISSUE REQ'D.
AMS # DESCRIPTION 2. POLES SHALL BE PRE-DRILLED WITH 20MM DIA HOLES
CODE UNIT QTY.

102
AT LOCATIONS SPECIFIED IN THIS DRAWING.
TENSION SET
SHEILD WIRE 1 1000390097 EA 8 BOLT: STEEL MACHINE: 3/4" IN.x14 IN. LONG 3. ALL PRE-DRILLED HOLES SHALL BE PROVIDED WITH
SEE DETAIL

OF
CAPS OR PLUGS (DURABLE PLASTIC OR COMPOSITE
(TYPICAL FOR 12) 2 1000366536 EA 3 CONNECTOR: COMPRESSION, 4/0 AWG MATERIALS).

CONSENT
4. EARTHING NUT SHALL BE PROVIDED WITH BOLT AND
3 1000393239 EA 6 CLEVIS: SOCKET EYE, 21MM, 15.9MM
4 5 WASHER.

5. POLE SHALL BE PERMANENTLY MARKED WITH MANU-

898
4 1000233194 EA 18 WASHER: SPRING: FOR ƒ IN. BOLT
3 4 5 6 8 9 10
FACTURERS NAME YEAR OF MANUFACTURE LEGNTH

CAL FOR 6) 5 1000233149 EA 24 WASHER: ROUND, FLAT FOR ƒ IN. BOLT AND ULTIMATE LOAD RATING.
TYPI
(

TTEN
1000387225 INSULATOR: SUSPENSION 6. CONTRACTOR SHALL NOT INSTALL BOTTOM LINE
6 EA 12
AND GROUND WIRE IN CASE OF 1-PHASE 2-WIRES+

WRI
7 1000889281 EA POLE: STEEL, OCTAGONAL 55FEET OR REQUIRED LENGTH SHIELD WIRE.
1

127
7. POD POLE TAG MUST BE INSTALLED IN ALL POLES
1000390607 CLAMP: DEAD END, ALUMINUM, FOR # 4 AWG TO # 2/0 AWG STRANDED

THE
8 EA 6
BEARING THE POLE NUMBER AND INSTALLATION DATE
1
9 1000391426 EA 6 CLEVIS: INSULATOR: CLEVIS-BALL CURVED BRAKET MTG, FORGED 8. GALVANIZED STEEL POLE MUST BE COATED WITH

127

THOUT
(TYPICAL FOR 6) ANTI-CORROSION COATING OF COAL TAR EPOXY
10 1000391984 EA 6 EYE; NUT, 3/4" SSZ. GALV.
AS PER 14-SAMSS-403.

127
11 1000168148 2

WI
EA TAG; BRASS TAG 9. INSULATORS SHALL BE RATED ACCORDINGLY FOR

34.5kV SYSTEM
34.5kV SYSTEM.

NG
10. REFER TO SAES-P-107, TABLE-1 FOR CONDUCTOR &
1220

DRAWI
POLE CLEARANCE
POLE CLEARANCES.

2 11. EITHER COMPOSITE OR PORCELAIN TYPE INSULATORS

MAY BE USED. REFER TO SAES-P-107 FOR DETAILS.

S
THI
12. FOR 55' POLE, OTHER POLE HEIGHTS, MAKE

ADJUSTMENT ACCORDINGLY. GUY WIRES SHALL BE

FROM
(TYPICAL FOR 12) VERTICAL. IN AREAS WHERE IS NOT FEASIBLE DUE
TO SITE CONDITIONS, A MINIMUM ANGLE OF 37 Deg
SHALL BE ADOPTED.

BE NED
OBTAI
PART,SHALL
1220

N
I
FULL,OR
REFERENCE DRAWINGS

7 DWG. CONTROL FOR J.O.

N
I ON
REPRODUCTI
127
127

SAUDIARAMCO.NO
127

GUY AND ANCHOR

OF
PROPERTY
10
NOTE

SOLE
SEE

11
15,000

THE
(SEE NOTE12)
2

ARE
11,000

N
(SEE NOTE12)

HEREI
FOR POLE GROUNDING
SEE DETAIL-1

NED
SCALE: NONE

CONTAI
REVISION VALIDATION
GROUND LEVEL
THIS REVISION NO. 00 IS COVERED, FOR ALL APPROVAL AND CERTIFICATION

REQUIREMENTS, PER SAEP-334, UNDER DRAWING COMPLETION CERTIFICATE NO:

ON
765200-0915-001

NFORMATI
DESIGN CERTIFICATION REVIEW FOR KEY DRAWINGS OTHER
(DESIGN AGENCY) REQUIRED (SAUDI ARAMCO)
CONCRETE
ENGG./DATE CERTIFIED BY/DATE CONST. AGENCY/DATE OPERATIONS/DATE BY/DATE

ANCHOR PLAN RM
09/01/15
JAB
09/01/15
RM
09/01/15
JAB
09/01/15
ON
POLE.

REV.NO. DATE REVISION DESCRIPTION

I
00 09/01/15 NEW STANDARD FOR STEEL POLE
L
DETAI

THE
JOB ORDER/EWO NO.
THIS REVISION IS NOT TO BE USED FOR
SEE

765200 CONSTRUCTION UNTIL CERTIFIED AND DATED

SAUDI ARABIAN OIL COMPANY

AND
DRAWING TYPE

ARMLESS ANGLE POLE (60°-90°) STD

NG
BEARING PLATE
13.8KV -34.5KV OVERHEAD POWERLINE

DRAWI
STANDARD DRAWING
FRONT ELEVATION
STD. DWG. SAUDI ARABIA

S
PLANT NO. INDEX DRAWING NUMBER SHT. NO. REV. NO.

THI
990 P AA-036142 005 00
Saudi Aramco 2615 ENG. (05/05)

RESTRICTED VECTOR CADD-01