SAUDIARAMCO.

NOTES:
LIST OF MATERIAL
1. ALL DIMENSIONS ARE IN MILLIMETER UNLESS

102
TENSION SET
OTHERWISE SPECIFIED.
SHEILD WIRE OR OPGW DWG. ISSUE REQ'D. 2. POLES SHALL BE PRE-DRILLED WITH 20MM DIA HOLES
AMS # DESCRIPTION
CODE UNIT QTY. AT LOCATIONS SPECIFIED IN THIS DRAWING.

3. ALL PRE-DRILLED HOLES SHALL BE PROVIDED WITH

1 1000390097 EA 12 BOLT: MACHINE: 3/4" DIA 14" IN. LONG GALV
CAPS OR PLUGS (DURABLE PLASTIC OR COMPOSITE

OF
898
1000390607 MATERIALS).
5 2 EA 6 CLAMP, DEAD END, ALUMINUM FOR # 4/0 AWG TO # 2/0 AWG STRANDED
10 3 4 2

CONSENT
4. EARTHING NUT SHALL BE PROVIDED WITH BOLT AND
7 8 EA
( CAL FOR 6)
TYPI 3 1000391426 6 CLEVIS: INSULATOR CLEVIS, BALL, CURVED BRACKET MTG, FORGED WASHER.

CAL FOR 1
TYPI
( 8) 5. POLE SHALL BE PERMANENTLY MARKED WITH MANU-
4 1000393239 EA 6 CLEVIS: SOCKET EYE , 21 MM, 15.9 MM (5/8 IN) INSIDE WD, 35 MM INSIDE LG
FACTURERS NAME YEAR OF MANUFACTURE LEGNTH

EA 6 EYE; NUT, 3/4" SSZ. GALV. AND ULTIMATE LOAD RATING.

5 1000391984

127

TTEN
6. CONTRACTOR SHALL NOT INSTALL BOTTOM LINE
6 1000393964 FT 3 TIE, INSULATOR, SIDE IN CASE OF 1-PHASE 2-WIRES+SHIELD WIRE.

WRI
1
127 7 1000233194 EA 18 LOCK: WASHER, SPRING: FOR 3/4 IN. BOLT 7. POD POLE TAG MUST BE INSTALLED IN ALL POLES
BEARING THE POLE NUMBER AND INSTALLATION DATE
EA

THE
8 1000233149 36 WASHER: ROUND, FLAT FOR ƒ IN. BOLT
8. GALVANIZED STEEL POLE MUST BE COATED WITH
127

9 1000386822 EA 3 INSULATOR: LINE POST, TIE TOP ANTI-CORROSION COATING OF COAL TAR EPOXY

THOUT
AS PER 14-SAMSS-403.
10 1000387225 EA 12 INSULATOR: SUSPENSION
9. INSULATORS SHALL BE RATED ACCORDINGLY FOR
229

13 1000889281 EA

WI
11 1 POLE: STEEL, 55FT OR REQUIRED LENGTH 34.5kV SYSTEM
34.5kV SYSTEM.

10. REFER TO SAES-P-107, TABLE-1 FOR CONDUCTOR &

1220

12 1000386998 EA 3 STUD , POST INSULATOR, SHORT 3/4" DIA

NG
POLE CLEARANCE
POLE CLEARANCE.

DRAWI
254

13 1000366536 EA 3 CONNECTOR; COMPRESSION SLEEVE TYPE FOR 4/0 AWG CONDUCTOR 11. EITHER COMPOSITE OR PORCELAIN TYPE INSULATORS

MAY BE USED. REFER TO SAES-P-107 FOR DETAILS.

14 1000390451 EA 3 BRACKET, FOR POST INSULATOR
12. FOR 55' POLE, OTHER POLE HEIGHTS, MAKE

S
THI
15 08-513-446 EA 2 TAG; BRASS TAG ADJUSTMENT ACCORDINGLY. GUY WIRES SHALL BE
9 12 14 6
INSTALLED AT A TRUE ANGLE OF 45Deg. TO THE
( CAL FOR 3)
TYPI VERTICAL. IN AREAS WHERE IS NOT FEASIBLE DUE

FROM
TO SITE CONDITIONS, A MINIMUM ANGLE OF 37 Deg
SHALL BE ADOPTED.

NED
OBTAI
254

BE
PART,SHALL
127
229

13
1220

REFERENCE DRAWINGS

N
I
FULL,OR
254

N
I ON
11

REPRODUCTI
127

SAUDIARAMCO.NO
127
864

127

GUY AND ANCHOR

229

13

OF
254

PROPERTY
10
NOTE

SOLE
SEE

THE
ARE
13,000 (SEE NOTE12)

N
11,000 (SEE NOTE12)

HEREI
15

NG
FOR POLE GROUNDI
L-
SEE DETAI 1

NED
SCALE: NONE

CONTAI
REVISION VALIDATION

GROUND LEVEL THIS REVISION NO. 00 IS COVERED, FOR ALL APPROVAL AND CERTIFICATION

REQUIREMENTS, PER SAEP-334, UNDER DRAWING COMPLETION CERTIFICATE NO:

ON
765200-0915-001

NFORMATI
DESIGN CERTIFICATION REVIEW FOR KEY DRAWINGS OTHER
(DESIGN AGENCY) REQUIRED (SAUDI ARAMCO)
L
DETAI

ENGG./DATE CERTIFIED BY/DATE CONST. AGENCY/DATE OPERATIONS/DATE BY/DATE

CONCRETE RM JAB RM JAB

09/01/15 09/01/15 09/01/15 09/01/15
ANCHOR REV.NO. DATE REVISION DESCRIPTION

I
2000 PLAN
ON

00 09/01/15 NEW STANDARD FOR STEEL POLE

POLE.

FOUNDATI

THE
NTS JOB ORDER/EWO NO.
THIS REVISION IS NOT TO BE USED FOR
765200 CONSTRUCTION UNTIL CERTIFIED AND DATED

SAUDI ARABIAN OIL COMPANY

SEE

AND
DRAWING TYPE

ARMLESS ANGLE POLE (30°-60°) STD

NG
13.8KV -34.5KV OVERHEAD POWERLINE

DRAWI
BEARING PLATE

STANDARD DRAWING
FRONT ELEVATION
STD. DWG. SAUDI ARABIA

S
PLANT NO. INDEX DRAWING NUMBER SHT. NO. REV. NO.

THI
990 P AA-036142 004 00
Saudi Aramco 2615 ENG. (05/05)

RESTRICTED VECTOR CADD-01