NDT Bridges

NON DESTRUCTIVE TESTING
OF
BRIDGES
June 2005
INDIAN RAILWAY INSTITUTE OF CIVIL ENGINEERING

PUNE 411001
PREFACE
Non-destructive testing of bridges has assumed a

greater significance in the present scenario because our
existing inspection system is not adequate to identify the
internal defects in the structures. With the recent collapses
of bridges in India and other countries the objective inspection
of bridges has become the need of the hour.
Indian Railway Bridge Manual (IRBM) prescribes

periodical Health Monitoring of Very Important Bridges by an
independent agency which includes corrosion monitoring,
deterioration of material, system damage, retrofitting etc. All
these can be done by using suitable NDT methods. Since
the work will be executed by the independent agency, it is
important to understand the details of the testing procedures
as the engineer may have to supervise the work at the site.
Since non-destructive testing methods do not form part of
IRBM, the various methods used for testing different types of
bridges have been included in this publication.
I hope this book will be found very much useful by

field engineers, who are entrusted with the work of non-
destructive testing of bridges, and will help as guide for
implementation of testing methods for inspection and testing
of bridges.
Shiv Kumar
Director
IRICEN/PUNE
ACKNOWLEDGEMENT
The subject “non-destructive testing of bridges” is

being taught during various courses at IRICEN. In the present
scenario, it needs special attention. Even though a lot of
information is available on this subject , yet when it pertaining
to various types of bridges i.e. concrete, steel and masonry
bridges, it is not available at one place.
The IRICEN publication is an attempt to compile all

the relevant information regarding various NDT methods
commonly in use for testing of all types of bridges on Indian
Railways. Even though the publication is primarily aimed at
Railway Engineers, the basic concepts are equally applicable
to road bridges also.
It would not be out of place to acknowledge the

support and assistance rendered by IRICEN faculty and staff
in the above efforts. I am particularly thankful to Shri. Praveen
Kumar, Prof. (Computers), who has provided logistic
assistance for printing of this book. The word processing of
the manuscript and repeated editings thereof has been done
by Mrs. Gayatri. I also acknowledge the help of drawing
staff of IRICEN who have assisted in preparation of drawings.
Above all, the author is grateful to Sri Shiv Kumar,

Director, IRICEN for his encouragement and advice for
improving the document.
A.K. Gupta
Professor/Track-1
IRICEN/Pune
CONTENTS
CHAPTER-1 NON - DESTRUCTIVE TESTING OF BRIDGES -

GENERAL
1.1 Introduction 1
1.2 Concrete Bridges 1
1.3 Steel Bridges 4
1.4 Masonry Bridges 5
CHAPTER-2 NON – DESTRUCTIVE TESTS FOR STRENGTH

ESTIMATION OF CONCRETE
2.1 Rebound hammer test (Schmidt Hammer) 6
2.1.1. Object 6
2.1.2 Principle 7
2.1.3 Methodology 8
2.1.4 Procedure for obtaining correlation 9
between compressive strength of concrete
and rebound number
2.1.5 Interpretation of results 10
2.1.6 Standards 11
2.2 Ultrasonic Pulse Velocity Tester 11
2.2.1 Object 11
2.2.2 Principle 12
2.2.3 Methodology 13
2.2.4 Determination of pulse velocity 17
2.2.5 Interpretation of Results 18
2.2.6 Factors influencing pulse velocity 19
measurements
2.3 Combined use of Rebound hammer and Ultrasonic 23

Pulse Velocity Method
2.4 Pull Off Test 23
2.4.1 Object 24
2.4.2 Principle 24
2.4.4 Advantages and Limitations 26
2.4.5 Standards 27
2.5 Pull out Test 27
2.5.1 Object 27
2.5.2 Principle 27
2.5.6 Standards 30
2.6 The Break-off Test 30
2.6.1 Object 30
2.6.2 Principle 30
2.6.5 Standards 35
2.7 Penetration Resistance Methods 36
2.7.1 Object 36
2.7.2 Principle 37
2.7.5 Standards 38
CHAPTER-3 NON – DESTRUCTIVE TESTS FOR CORROSION

ASSESSMENT, LOCATION AND DIAMETER OF
REINFORCEMENT AND COVER THICKNESS OF
CONCRETE BRIDGES
3.1 Introduction 39
3.2 Half-cell Potential Measurement Method 39

3.2.1 Object 41
3.2.2 Principle 41
3.2.4 Interpretation of test results 43
3.2.5 Limitations 44
3.2.6 Standards 44
3.3 Resistivity Test 44
3.3.1 Object 45
3.3.2 Principle 45
3.4 Tests for carbonation of Concrete 47
3.5 Test for chloride content of concrete 48
3.6 Profometer 48
3.6.1 Object 49
3.6.2 Principle 49
3.7 Micro Covermeter 51
3.7.1 Object 52
3.7.2 Principle 52
CHAPTER-4 NON – DESTRUCTIVE TESTS FOR DETECTION

OF CRACKS / VOIDS / DELAMINATIONS ETC. IN
CONCRETE BRIDGES
4.1 Introduction 54
4.2 Infrared thermographic techniques 54
4.2.1 Object 56
4.2.2 Principle 56
4.2.4 Advantages & Limitations 57
4.3 Acoustic Emission Technique 58
4.3.1 Object 60
4.3.2 Principle 60
4.4 Short Pulse Radar Method 62
4.4.1 Object 62
4.4.2 Principle 63
4.5 Stress Wave Propagation Methods 65
4.5.1 Pulse Echo method 66

4.5.2 Impact Echo Method 67
4.5.3 Impulse Response method 68
CHAPTER-5 NON – DESTRUCTIVE TESTING OF STEEL

BRIDGES
5.1 Introduction 70
5.2 Liquid Penetrant Inspection 70
5.2.2 Material Properties 72
5.2.3 Advantages and Disadvantages 73
5.3 Magnetic Particle Inspection 73
5.3.1 Principle 74
5.3.2 Equipments and Methodology 76
5.4 Eddy Current Testing 78
5.5 Radiographic Testing 81
5.6 Ultrasonic Inspection 83
5.6.1 Principle 83
5.6.2 Calibration and reference standards 86
5.6.3 Application of Ultrasonic Testing Method 87
CHAPTER-6 NON – DESTRUCTIVE TESTING OF MASONRY

BRIDGES
6.1 Introduction 89
6.2 Flat Jack Testing 89
6.3 Impact Echo Testing 90
6.4 Impulse Radar Testing 91
6.5 Infrared Thermography 92
LIST OF FIRMS DEALING WITH NDT EQUIPMENTS 93
REFERENCES 94
CHAPTER 1
NON-DESTRUCTIVE TESTING OF BRIDGES - GENERAL
1.1 Introduction
There are about 1,20,000 bridges of different types with
varying spans on Indian Railways. About 40% of these bridges
are over 100 years old and have completed their codal life. The
present method of bridge inspection is mostly visual and give only
subjective assessment of the condition of bridge. Moreover present
inspection system is not capable of assessing hidden defects, if
any.
We may group the various bridges mainly in three types,

based upon material of construction.
(i) Concrete bridges

(ii) Steel bridges
(iii) Masonry bridges
Various types of bridges are having their own strengths,

weaknesses and maintenance related problems. Each type of
bridge is having different properties i.e. concrete is a heteroge-
neous material but the steel is a denser and homogeneous mate-
rial. Similarly in masonry structures, the condition of joints and
material of construction is of utmost importance. Considering the
uniqueness of each type of bridge , there are different methods
adopted for inspection and maintenance based on material of con-
struction. In this book, various Non-Destructive Testing (NDT)
methods for testing concrete , steel and masonry bridges have
been discussed separately.
1.2 Concrete Bridges

The quality of new concrete structures is dependent on
many factors such as type of cement, type of aggregates, water
cement ratio, curing, environmental conditions etc. Besides this,
(2)
the control exercised during construction also contributes a lot to

achieve the desired quality. The present system of checking slump
and testing cubes, to assess the strength of concrete, in struc-
ture under construction, are not sufficient as the actual strength of
the structure depend on many other factors such as proper com-
paction, effective curing also.
Considering the above requirements, need of testing of

hardened concrete in new structures as well as old structures, is
there to asses the actual condition of structures. Non-Destructive
Testing (NDT) techniques can be used effectively for investigation
and evaluating the actual condition of the structures. These tech-
niques are relatively quick, easy to use, cheap and give a general
indication of the required property of the concrete.This approach
will enable us to find suspected zones ,thereby reducing the time
and cost of examining a large mass of concrete. The choice of a
particular NDT method depends upon the property of concrete to
be observed such as strength, corrosion, crack monitoring etc.
The subsequent testing of structure will largely depend upon the
result of preliminary testing done with the appropriate NDT tech-
nique.
The NDT being fast, easy to use at site and relatively

less expensive can be used for
(i) Testing any number of points and locations

(ii) Assessing the structure for various distressed
conditions
(iii) Assessing damage due to fire, chemical attack,
impact, age etc.
(iv) Detecting cracks, voids, fractures, honeycombs
and weak locations
(v) Assessing the actual condition of reinforcement
Many of NDT methods used for concrete testing have their

origin to the testing of more homogeneous, metallic system. These
methods have a sound scientific basis, but heterogeneity of con-
crete makes interpretation of results somewhat difficult. There
could be many parameters such as materials, mix, workmanship
and environment, which influence the result of measurements.
(3)
Moreover the test measure some other property of concrete (e.g.

hardness) yet the results are interpreted to assess the different
property of the concrete e.g. (strength). Thus, interpretation of the
result is very important and a difficult job where generalization is
not possible. Even though operators can carry out the test but
interpretation of results must be left to experts having experience
and knowledge of application of such non-destructive tests.
Variety of NDT methods have been developed and are

available for investigation and evaluation of different parameters
related to strength, durability and overall quality of concrete. Each
method has some strength and some weakness. Therefore pru-
dent approach would be to use more than one method in combina-
tion so that the strength of one compensates the weakness of the
other. The various NDT methods for testing concrete bridges are
listed below –
A. For strength estimation of concrete
(i) Rebound hammer test

(ii) Ultrasonic Pulse Velocity Tester
(iii) Combined use of Ultrasonic Pulse Ve-
locity tester and rebound hammer test
(iv) Pull off test
(v) Pull out test
(vi) Break off test
(vii) Windsor Probe test
B. For assessment of corrosion condition of

reinforcement and to determine reinforcement
diameter and cover
(i) Half cell potentiometer

(ii) Resistively meter test
(iii) Test for carbonation of concrete
(iv) Test for chloride content of concrete
(v) Profometer
(vi) Micro covermeter
(4)
C. For detection of cracks/voids/ delamination etc.
(i) Infrared thermographic technique

(ii) Acoustic Emission techniques
(iii) Short Pulse Radar methods
(iv) Stress wave propagation methods
- pulse echo method
- impact echo method
- response method
All the above said methods have been discussed in detail

in this book.
1.3 Steel Bridges

On Indian Railways, the superstructure of the large num-
ber of major bridges is of steel, and substructure is generally of
concrete/masonry. These steel bridges are fabricated using struc-
tural steel section i.e. channels, angles ,plates and I-sections etc.
The bridges are subjected to severe dynamic stresses under pas-
sage of traffic and because of these stresses, the deterioration of
the materials takes place.
In our system of inspection, we are mainly carrying out

the visual inspection of the various parts of bridges, rivet testing
and inspection of bearings etc. But all these methods do not
given any indication about the microcracking, presence of flaws/
internal blow holes/lamination etc. in the bridge members. More-
over some of the members of the bridge girders are difficult to
inspect because of inaccessibility and in those cases, the NDT
technique can be used effectively for inspection and evaluation of
structures.
The various NDT methods for testing steel bridges are

listed below:
(i) Liquid penetrant testing

(5)
(ii) Magnetic particle testing

(iii) Electromagnetic testing or Eddy current testing
(iv) Radiography
(v) Ultrasonic testing
All the above said methods have been discussed in de-

tail in this book.
1.4 Masonry Bridges

A large no. of bridges on Indian Railways are masonry
bridges in which foundation or substructure is of either stone or
brick masonry. In addition, a large no. of bridges are masonry arch
bridges which have become quite old and already outlived their
design life. The weakest location in a masonry bridge is the joint,
as the deterioration gets initiated from the joints. With the pas-
sage of loads and over a period of time the deterioration of the
material itself take place due to which the strength of the masonry
structures gets affected. At the time of inspection, normally the
condition of joints or the material on the outer surface is noted but
it does not give any indication about the inherent defects within
the structures. Moreover the present system of inspection is not
about detecting the deterioration in strength of the stone/brick ma-
sonry because of the weathering action and other factors. In In-
dia, the NDT of masonry structures is still in necessant stage.
There are lot of methods available for NDT of masonry structure,
as indicated below:
(a) Flat Jack Testing

(b) Impact Echo Testing
(c) Impulse radar testing
(d) Infrared thermography
As the application of the above said NDT methods for

masonry inspection is not very common in India, details given in
this book are just for general guidance.
CHAPTER-2
NON-DESTRUCTIVE TESTS FOR STRENGTH

ESTIMATION OF CONCRETE
2.1. Rebound hammer test (Schmidt Hammer)
This is a simple, handy tool, which can be used to provide

a convenient and rapid indication of the compressive strength of
concrete. It consists of a spring controlled mass that slides on a
plunger within a tubular housing. The schematic diagram showing
various parts of a rebound hammer is given as Fig 2.1.1
1. Concrete surface; 2. Impact spring; 3. Rider on guide rod; 4.

Window and scale; 5. Hammer guide; 6. Release catch; 7. Com-
pressive spring; 8. Locking button; 9. Housing; 10. Hammer mass;
11. Plunger
Fig. 2.1.1 Components of a Rebound Hammer
2.1.1 Object
The rebound hammer method could be used for –

(a) Assessing the likely compressive strength of concrete with
the help of suitable co-relations between rebound index and
compressive strength.
(b) Assessing the uniformity of concrete
(7)
(c) Assessing the quality of concrete in relation to standard

requirements.
(d) Assessing the quality of one element of concrete in relation
to another
This method can be used with greater confidence for dif-

ferentiating between the questionable and acceptable parts of a
structure or for relative comparison between two different struc-
tures.
2.1.2 Principle
The method is based on the principle that the rebound of

an elastic mass depends on the hardness of the surface against
which mass strikes. When the plunger of rebound hammer is
pressed against the surface of the concrete, the spring controlled
mass rebounds and the extent of such rebound depends upon the
surface hardness of concrete. The surface hardness and therefore
the rebound is taken to be related to the compressive strength of
the concrete. The rebound value is read off along a graduated
scale and is designated as the rebound number or rebound index.
The compressive strength can be read directly from the graph
provided on the body of the hammer.
The impact energy required for rebound hammer for

different applications is given below –
Sr. Approximate impact

No. Application energy required for
the rebound
hammers (N-m)
1. For testing normal weight concrete 2.25
2. For light weight concrete or small
and impact sensitive part of
concrete 0.75
3. For testing mass concrete i.e. in
roads, airfield pavements and
hydraulic structures 30.00
(8)
Depending upon the impact energy, the hammers are clas-

sified into four types i.e. N, L, M & P. Type N hammer having an
impact energy of 2.2 N-m and is suitable for grades of concrete
from M-15 to M-45. Type L hammer is suitable for lightweight
concrete or small and impact sensitive part of the structure. Type
M hammer is generally recommended for heavy structures and
mass concrete. Type P is suitable for concrete below M15 grade.
2.1.3 Methodology
Before commencement of a test, the rebound hammer

should be tested against the test anvil, to get reliable results. The
testing anvil should be of steel having Brinell hardness number of
about 5000 N/mm2. The supplier/manufacturer of the rebound
hammer should indicate the range of readings on the anvil suitable
for different types of rebound hammer.
For taking a measurement, the hammer should be held at

right angles to the surface of the structure. The test thus can be
conducted horizontally on vertical surface and vertically upwards
or downwards on horizontal surfaces (Fig.2.1.2).
VERTICAL DOWNWARD
POSITION
VERTICAL SURFACE
HORIZONTAL POSITION
VERTICAL UPWARD POSITION
Fig. 2.1.2 Various positions of Rebound Hammer

(9)
If the situation so demands, the hammer can be held at

intermediate angles also, but in each case, the rebound number
will be different for the same concrete.
The following should be observed during testing.

(a) The surface should be smooth, clean and dry
(b) The loosely adhering scale should be rubbed off
with a grinding wheel or stone, before testing
(c) Do not conduct test on rough surfaces resulting
from incomplete compaction, loss of grout,
spalled or tooled surfaces.
(d) The point of impact should be at least 20mm away
from edge or shape discontinuity.
Around each point of observation, six readings of rebound

indices are taken and average of these readings after deleting out-
liers as per IS 8900:1978 is taken as the rebound index for the
point of observation.
2.1.4 Procedure for obtaining correlation between compressive

strength of concrete and rebound number
The most satisfactory way of establishing a correlation

between compressive strength of concrete and its rebound num-
ber is to measure both the properties simultaneously on concrete
cubes. The concrete cubes specimens are held in a compression
testing machine under a fixed load, measurements of rebound
number taken and then the compressive strength determined as
per IS 516: 1959. The fixed load required is of the order of 7 N/
mm2 when the impact energy of the hammer is about 2.2 Nm. The
load should be increased for calibrating rebound hammers of greater
impact energy and decreased for calibrating rebound hammers of
lesser impact energy. The test specimens should be as large a
mass as possible in order to minimize the size effect on the test
result of a fullscale structure. 150mm cube specimens are pre-
ferred for calibrating rebound hammers of lower impact energy
(2.2Nm), whereas for rebound hammers of higher impact energy,
for example 30 Nm, the test cubes should not be smaller than
300mm.
(10)
If the specimens are wet cured, they should be removed

from wet storage and kept in the laboratory atmosphere for about
24 hours before testing. To obtain a correlation between rebound
numbers and strength of wet cured and wet tested cubes, it is
necessary to establish a correlation between the strength of wet
tested cubes and the strength of dry tested cubes on which re-
bound readings are taken. A direct correlation between rebound
numbers on wet cubes and the strength of wet cubes is not rec-
ommended. Only the vertical faces of the cubes as cast should be
tested. At least nine readings should be taken on each of the two
vertical faces accessible in the compression testing machine when
using the rebound hammers. The points of impact on the speci-
men must not be nearer an edge than 20mm and should be not
less than 20mm from each other. The same points must not be
impacted more than once.
2.1.5 Interpretation of results
After obtaining the correlation between compressive

strength and rebound number, the strength of structure can be
assessed. In general, the rebound number increases as the
strength increases and is also affected by a number of param-
eters i.e. type of cement, type of aggregate, surface condition
and moisture content of the concrete, curing and age of concrete,
carbonation of concrete surface etc. Moreover the rebound index
is indicative of compressive strength of concrete upto a limited
depth from the surface. The internal cracks, flaws etc. or hetero-
geneity across the cross section will not be indicated by rebound
numbers.
As such the estimation of strength of concrete by rebound

hammer method cannot be held to be very accurate and probable
accuracy of prediction of concrete strength in a structure is ± 25
percent. If the relationship between rebound index and compres-
sive strength can be found by tests on core samples obtained
from the structure or standard specimens made with the same
concrete materials and mix proportion, then the accuracy of re-
sults and confidence thereon gets greatly increased.
(11)
2.1.6 Standards
The rebound hammer testing can be carried out as per IS-

13311 (Pt.2).
2.2 Ultrasonic Pulse Velocity Tester
Ultrasonic instrument is a handy, battery operated and

portable instrument used for assessing elastic properties or con-
crete quality. The apparatus for ultrasonic pulse velocity mea-
surement consists of the following (Fig. 2.2.1) –
(a) Electrical pulse generator
(b) Transducer – one pair
(c) Amplifier
(d) Electronic timing device
Fig.2.2.1 Apparatus for UPV measurement
2.2.1 Object
The ultrasonic pulse velocity method could be used to

establish:
(a) the homogeneity of the concrete
(b) the presence of cracks, voids and other imper
fections
(12)
(c) change in the structure of the concrete which may

occur with time
(d) the quality of concrete in relation to standard re-
quirement
(e) the quality of one element of concrete in relation
to another
(f) the values of dynamic elastic modulus of the con-
crete
2.2.2 Principle
The method is based on the principle that the velocity of

an ultrasonic pulse through any material depends upon the density,
modulus of elasticity and Poisson’s ratio of the material.
Comparatively higher velocity is obtained when concrete quality is
good in terms of density, uniformity, homogeneity etc. The
ultrasonic pulse is generated by an electro acoustical transducer.
When the pulse is induced into the concrete from a transducer, it
undergoes multiple reflections at the boundaries of the different
material phases within the concrete. A complex system of stress
waves is developed which includes longitudinal (compression), shear
(transverse) and surface (Reyleigh) waves. The receiving transducer
detects the onset of longitudinal waves which is the fastest.
The velocity of the pulses is almost independent of the

geometry of the material through which they pass and depends
only on its elastic properties. Pulse velocity method is a convenient
technique for investigating structural concrete.
For good quality concrete pulse velocity will be higher

and for poor quality it will be less. If there is a crack, void or flaw
inside the concrete which comes in the way of transmission of the
pulses, the pulse strength is attenuated and it passed around the
discontinuity, thereby making the path length longer. Consequently,
lower velocities are obtained. The actual pulse velocity obtained
depends primarily upon the materials and mix proportions of
concrete. Density and modulus of elasticity of aggregate also
significantly affects the pulse velocity.
Any suitable type of transducer operating within the fre-

(13)
quency range of 20 KHz to 150KHz may be used. Piezoelectric

and magneto-strictive types of transducers may be used and the
latter being more suitable for the lower part of the frequency range.
Following table indicates the natural frequency of transducers for
different path lengths –
Path length Natural Frequency Minimum

(mm) of Transducer transverse
(KHz) dimensions of
members (mm)
Upto 500 150 25
500 – 700 >60 70
700 – 1500 >40 150
above 1500 >20 300
The electronic timing device should be capable of mea-

suring the time interval elapsing between the onset of a pulse
generated at the transmitting transducer and onset of its arrival at
receiving transducer. Two forms of the electronic timing apparatus
are possible, one of which use a cathode ray tube on which the
leading edge of the pulse is displayed in relation to the suitable
time scale, the other uses an interval timer with a direct reading
digital display. If both the forms of timing apparatus are available,
the interpretation of results becomes more reliable.
2.2.3 Methodology
The equipment should be calibrated before starting the

observation and at the end of test to ensure accuracy of the
measurement and performance of the equipment. It is done by
measuring transit time on a standard calibration rod supplied along
with the equipment.
A platform/staging of suitable height should be erected to

have an access to the measuring locations. The location of
(14)
measurement should be marked and numbered with chalk or similar

thing prior to actual measurement (pre decided locations).
Mounting of Transducers
The direction in which the maximum energy is propagated

is normally at right angles to the face of the transmitting trans-
ducer, it is also possible to detect pulses which have travelled
through the concrete in some other direction. The receiving trans-
ducer detects the arrival of component of the pulse which arrives
earliest. This is generally the leading edge of the longitudinal
vibration. It is possible, therefore, to make measurements of pulse
velocity by placing the two transducers in the following manners
(Fig.2.2.2)
Direct Transmission
Semi-direct Transmission
(Cross probing)
Indirect Transmission
(Surface probing)
Fig.2.2.2 Various Methods of UPV Testing

(15)
(a) Direct Transmission (on opposite faces) – This arrangement

is the most preferred arrangement in which transducers are
kept directly opposite to each other on opposite faces of the
concrete. The transfer of energy between transducers is
maximum in this arrangement. The accuracy of velocity
determination is governed by the accuracy of the path length
measurement. Utmost care should be taken for accurate
measurement of the same. The couplant used should be
spread as thinly as possible to avoid any end effects resulting
from the different velocities of pulse in couplant and concrete.
(b) Semi-direct Transmission: This arrangement is used when it

is not possible to have direct transmission (may be due to
limited access). It is less sensitive as compared to direct
transmission arrangement. There may be some reduction in
the accuracy of path length measurement, still it is found to
be sufficiently accurate. This arrangement is otherwise similar
to direct transmission.
(c) Indirect or Surface Transmission: Indirect transmission should

be used when only one face of the concrete is accessible
(when other two arrangements are not possible). It is the
least sensitive out of the three arrangements. For a given
path length, the receiving transducer get signal of only about
2% or 3% of amplitude that produced by direct transmission.
Furthermore, this arrangement gives pulse velocity
measurements which are usually influenced by the surface
concrete which is often having different composition from that
below surface concrete. Therefore, the test results may not
be correct representative of whole mass of concrete. The
indirect velocity is invariably lower than the direct velocity on
the same concrete element. This difference may vary from
5% to 20% depending on the quality of the concrete. Wherever
practicable, site measurements should be made to determine
this difference.
There should be adequate acoustical coupling between

concrete and the face of each transducer to ensure that the
ultrasonic pulses generated at the transmitting transducer should
be able to pass into the concrete and detected by the receiving
(16)
transducer with minimum losses. It is important to ensure that

the layer of smoothing medium should be as thin as possible.
Couplant like petroleum jelly, grease, soft soap and kaolin/glycerol
paste are used as a coupling medium between transducer and
concrete.
Special transducers have been developed which impart or

pick up the pulse through integral probes having 6mm diameter
tips. A receiving transducer with a hemispherical tip has been
found to be very successful. Other transducer configurations have
also been developed to deal with special circumstances. It should
be noted that a zero adjustment will almost certainly be required
when special transducers are used.
Most of the concrete surfaces are sufficiently smooth.

Uneven or rough surfaces, should be smoothened using
carborundum stone before placing of transducers. Alternatively, a
smoothing medium such as quick setting epoxy resin or plaster
can also be used, but good adhesion between concrete surface
and smoothing medium has to be ensured so that the pulse is
propagated with minimum losses into the concrete.
Transducers are then pressed against the concrete surface

and held manually. It is important that only a very thin layer of
coupling medium separates the surface of the concrete from its
contacting transducer. The distance between the measuring points
should be accurately measured.
Repeated readings of the transit time should be observed

until a minimum value is obtained.
Once the ultrasonic pulse impinges on the surface of the

material, the maximum energy is propagated at right angle to the
face of the transmitting transducers and best results are, therefore,
obtained when the receiving transducer is placed on the opposite
face of the concrete member known as Direct Transmission.
The pulse velocity can be measured by Direct

Transmission, Semi-direct Transmission and Indirect or Surface
(17)
Transmission. Normally, Direct Transmission is preferred being

more reliable and standardized. (various codes gives correlation
between concrete quality and pulse velocity for Direct Transmission
only). The size of aggregates influences the pulse velocity
measurement. The minimum path length should be 100mm for
concrete in which the nominal maximum size of aggregate is 20mm
or less and 150mm for aggregate size between 20mm and 40mm.
Reinforcement, if present, should be avoided during pulse

velocity measurements, because the pulse velocity in the rein-
forcing bars is usually higher than in plain concrete. This is be-
cause the pulse velocity in steel is 1.9 times of that in concrete.
In certain conditions, the first pulse to arrive at the receiving trans-
ducer travels partly in concrete and partly in steel. The apparent
increase in pulse velocity depends upon the proximity of the mea-
surements to the reinforcing bars, the diameter and number of
bars and their orientation with respect to the path of propagation.
It is reported that the influence of reinforcement is generally small
if the bar runs in the direction right angle to the pulse path for bar
diameter less than12 mm. But if percentage of steel is quite high
or the axis of the bars are parallel to direction of propagation, then
the correction factor has to be applied to the measured values.
2.2.4. Determination of pulse velocity
A pulse of longitudinal vibration is produced by an electro-

acoustical transducer, which is held in contact with one surface of
the concrete member under test. After traversing a known path
length(L) in the concrete, the pulse of vibration is converted into an
electrical signal by a second electro-acoustical transducer, and
electronic timing circuit enable the transit time (T) of the pulse to
be measured. The pulse velocity (V) is given by
V=L/T
where,
V = Pulse velocity
L = Path length
T = Time taken by the pulse to traverse the path length
(18)
2.2.5 Interpretation of Results
The ultrasonic pulse velocity of concrete can be related to

its density and modulus of elasticity. It depends upon the materi-
als and mix proportions used in making concrete as well as the
method of placing ,compacting and curing of concrete. If the con-
crete is not compacted thoroughly and having segregation, cracks
or flaws, the pulse velocity will be lower as compare to good con-
crete, although the same materials and mix proportions are used.
The quality of concrete in terms of uniformity, can be assessed
using the guidelines given in table below:
Table: Criterion for Concrete Quality Grading

(As per IS 13311(Part 1) : 1992)
Sr. Pulse velocity by cross Concrete
No. probing (km/sec.) quality grading
1 Above 4.5 Excellent
2 3.5 to 4.5 Good
3 3.0 to 3.5 Medium
4 Below 3.0 Doubtful
Note: in case of doubtful quality, it will be desirable to
carry out further tests.
Since actual value of the pulse velocity in concrete de-

pends on a number of parameters, so the criterion for assessing
the quality of concrete on the basis of pulse velocity is valid to the
general extent. However, when tests are conducted on different
parts of the structure, which have been built at the same time with
similar materials, construction practices and supervision and sub-
sequently compared, the assessment of quality becomes more
meaningful and reliable.
The quality of concrete is usually specified in terms of

strength and it is therefore, sometimes helpful to use ultrasonic
pulse velocity measurements to give an estimate of strength. The
relationship between ultrasonic pulse velocity and strength is
affected by a number of factor including age, curing conditions,
(19)
moisture condition, mix proportions, type of aggregate and type of

cement.
The assessment of compressive strength of concrete from

ultrasonic pulse velocity values is not accurate because the corre-
lation between ultrasonic pulse velocity and compressive strength
of concrete is not very clear. Because there are large number of
parameters involved, which influence the pulse velocity and com-
pressive strength of concrete to different extents. However, if de-
tails of material and mix proportions adopted in the particular struc-
ture are available, then estimate of concrete strength can be made
by establishing suitable correlation between the pulse velocity and
the compressive strength of concrete specimens made with such
material and mix proportions, under environmental conditions simi-
lar to that in the structure. The estimated strength may vary from
the actual strength by ± 20 percent. The correlation so obtained
may not be applicable for concrete of another grade or made with
different types of material.
2.2.6. Factors influencing pulse velocity measurement
The pulse velocity depends on the properties of the con-

crete under test. Various factors which can influence pulse veloc-
ity and its correlation with various physical properties of concrete
are as under:
Moisture Content: The moisture content has chemical and physi-

cal effects on the pulse velocity. These effects are important to
establish the correlation for the estimation of concrete strength.
There may be significant difference in pulse velocity between a
properly cured standard cube and a structural element made from
the same concrete. This difference is due to the effect of different
curing conditions and presence of free water in the voids. It is
important that these effects are carefully considered when esti-
mating strength.
Temperature of Concrete: No significant changes in pulse ve-

locity, in strength or elastic properties occur due to variations of
the concrete temperature between 5° C and 30° C. Corrections to
pulse velocity measurements should be made for temperatures
(20)
outside this range, as given in table below:
Table – Effect of temperature on pulse transmission

BS 1881 (Pt 203 Year 1986)
Temperature °C Correction to the measured pulse

velocity in %
Air dried concrete Water
saturated
concrete
60 +5 +4
40 +2 +1.7
20 0 0
0 -0.5 -1
-4 -1.5 -7.5
Path Length: The path length (the distance between two trans-
ducers) should be long enough not to be significantly influenced
by the heterogeneous nature of the concrete. It is recommended
that the minimum path length should be 100mm for concrete with
20mm or less nominal maximum size of aggregate and 150mm
for concrete with 20mm and 40mm nominal maximum size of ag-
gregate. The pulse velocity is not generally influenced by changes
in path length, although the electronic timing apparatus may indi-
cate a tendency for slight reduction in velocity with increased path
length. This is because the higher frequency components of the
pulse are attenuated more than the lower frequency components
and the shapes of the onset of the pulses becomes more rounded
with increased distance travelled. This apparent reduction in ve-
locity is usually small and well within the tolerance of time mea-
surement accuracy.
With indirect transmission, there is some uncertainty re-

garding the exact length of the transmission path. It is, therefore,
preferable to make a series of measurements with placing trans-
ducers at varying distances to eliminate this uncertainty. To do
(21)
this, the transmitting transducer should be placed in contact with

the concrete surface at a fixed point “x” and the receiving trans-
ducer should be moved at fixed increments ‘x’n along a chosen line
on the surface. The transmission times recorded should be plot-
ted as points on a graph showing their relation to the distance
separating the transducers.( Fig.2.2.3).
Fig.2.2.3 Method for determination of pulse velocity
The slope of the best fitted straight line drawn through the
points should be measured and recorded as the mean pulse ve-
locity along the chosen line on the concrete surface. Where the
points measured and recorded in this way indicate a discontinu-
ity, it is likely that a surface crack or surface layer of inferior qual-
ity is present and the pulse velocity measured in such case is
unreliable.
(22)
Shape and Size of Specimen: The velocity of pulses of vibra-

tions is independent of the size and shape of specimen, unless its
least lateral dimension is less than a certain minimum value. Below
this value, the pulse velocity may be reduced appreciably. The
extent of this reduction depends mainly on the ratio of the wave-
length of the pulse vibrations to the least lateral dimension of the
specimen but it is insignificant if the ratio is less than unity. Table
given below shows the relationship between the pulse velocity in
the concrete, the transducer frequency and the minimum permis-
sible lateral dimension of the specimen.
Table: Effect of specimen dimension on pulse

transmission
BS 1881 (Part 203 Year 1986)
Transducer Minimum lateral dimension

Frequency in mm for Pulse specimen
in KHz velocity in concrete in Km/s
Vc = 3.5 Vc = 4.0 Vc = 4.5
24 146 167 188

54 65 74 83
82 43 49 55
150 23 27 30
This is particularly important in cases where concrete elements

of significantly different sizes are being compared.
Effect of Reinforcing Bars: The pulse velocity in reinforced con-

crete in vicinity of rebars is usually higher than in plain concrete of
the same composition because the pulse velocity in steel is al-
most twice to that in plain concrete. The apparent increase de-
pends upon the proximity of measurement to rebars, their num-
bers, diameter and their orientation. Whenever possible, mea-
surement should be made in such a way that steel does not lie in
or closed to the direct path between the transducers. If the same
is not possible, necessary corrections needs to be applied. The
correction factors for this purpose are enumerated in different codes.
(23)
2.3. Combined use of Rebound hammer and Ultrasonic

Pulse Velocity Method
In view of the relative limitations of either of the two methods

for predicting the strength of concrete, both ultrasonic pulse velocity
(UPV) and rebound hammer methods are sometimes used in
combination to alleviate the errors arising out of influence of
materials, mix and environmental parameters on the respective
measurements. Relationship between UPV, rebound hammer and
compressive strength of concrete are available based on laboratory
test specimen. Better accuracy on the estimation of concrete
strength is achieved by use of such combined methods. However,
this approach also has the limitation that the established
correlations are valid only for materials and mix having same
proportion as used in the trials. The intrinsic difference between
the laboratory test specimen and in-situ concrete (e.g. surface
texture, moisture content, presence of reinforcement, etc.) also
affect the accuracy of test results.
Combination of UPV and rebound hammer methods can

be used for the assessment of the quality and likely compressive
strength of in-situ concrete. Assessment of likely compressive
strength of concrete is made from the rebound indices and this is
taken to be indicative of the entire mass only when the overall
quality of concrete judged by the UPV is ‘good’. When the quality
assessed is ‘medium’, the estimation of compressive strength by
rebound indices is extended to the entire mass only on the basis
of other collateral measurement e.g. strength of controlled cube
specimen, cement content of hardened concrete by chemical
analysis or concrete core testing. When the quality of concrete is
‘poor’, no assessment of the strength of concrete is made from
rebound indices.
2.4 Pull Off Test
Pull off tester is microprocessor based, portable hand op-

erated and mechanical unit used for measuring the tensile strength
of in situ concrete. The tensile strength obtained can be corre-
lated with the compressive strength using previously established
empirical correlation charts. The apparatus for pull off test shall
(24)
consist of the following -
(a) 50mm dia steel disc with threaded rod screw

(b) Pull off tester
One commercially available pull off tester is shown in Fig 2.4.1.
Fig. 2.4.1 Pull Off Tester
2.4.1 Object
The pull of test could be used to establish:

(a) The compressive strength of concrete
(b) Tensile strength of in situ concrete
(c) The adhesive strength of all kinds of applied
coatings
(d) The bond strength of repairs and renovation works
on concrete surfaces
2.4.2 Principle
The pull off test is based on the concept that the tensile
force required to pull a metal disk, together with a layer of con-
crete, from the surface to which it is attached, is related to com-
pressive strength of concrete There are two basic approaches
that can be used. One is where the metal disk is glued directly to
(25)
the concrete surface and the stressed volume of the con-

crete lies close to the face of the disk, and the other is where
surface carbonation or skin effect are present and these can be
avoided by use of partial coring to an appropriate depth. Both the
approaches are illustrated in Fig. 2.4.2.
Fig. 2.4.2 Various Methods of Pull Off Testing
2.4.3 Methodology
The first step is to remove any laitance from the concrete

surface to expose the top of the coarse aggregate particles. This
is usually done using some sort of abrasion, using typically a wire
brush. The exposed concrete surface and metal disk are then
degreased to ensure good bonding of the adhesive. The adhesive
is generally a two part epoxy system. A thin layer of adhesive is
spread over the disk area and the meta disk is pressed firmly onto
the concrete surface. Excessive adhesive that is squeezed out
during this process should be removed before it sets. The curing
time needed for the adhesive depends upon the type of epoxy
used and surrounding environmental condition, although in most
of the situations a curing time of not more than 24 hours is required.
After the adhesive has cured sufficiently, the metal disk is “pulled”
from the concrete surface. The apparatus used for applying and
recording this tensile force is known as “Limpet” and this applies a
tensile force through a threaded rod screwed into the metal disk.
(26)
Equipments are available from 5 KN to 100 KN tensile force

capacities. The instrument mechanism makes it possible to pre-
select the rate of loading and actual tensile force applied is
displayed on LCD monitor. The memory allows transferring of
recorded data to PC.
From the recorded tensile force a nominal pull off tensile
strength is calculated on the basis of the disk diameter (usually
50mm). To convert this pull off tensile strength into a cube
compressive strength, a previously established empirical correlation
chart is used.
2.4.4 Advantages and Limitations
The main advantage of pull off test is that it is simple and

quick to perform. The entire process of preparing the surface and
bonding the steel disk normally doesn’t take more than 15 min-
utes. The damage caused to concrete surface after conducting
the test is very minor and can be repaired easily.
The main limitation of this method is, the curing time,

required for the adhesive. In most situations, it is normal practice
to apply the disk one day and complete the test next day. The
another problem is the failure of adhesive. The adhesive may fail
because of inferior quality of adhesive or improper surface prepa-
ration or unfavourable environmental conditions. If during testing,
the adhesive fails, the test result becomes meaningless.To com-
pensate for this type of problem, it is recommended that at least
six disks be used to estimate the compressive strength and, if
necessary, one of the individual test results can be eliminated if
an adhesive failure has occurred.
Another aspect of the pull off test is the correlation used

to determine the compressive strength. The single factor that has
the greatest effect on this relationship is the type of coarse aggre-
gate used in the concrete, the greatest difference being between
natural gravels and crushed rocks. Therefore, care should always
be taken to ensure that the correlation being used is applicable in
that situation.
(27)
2.4.5 Standards
The test is conducted as per BS-1881 part 207.
2.5 Pull out Test
The pull out test measures the force needed to extract an

embedded insert from a concrete mass. By using a previously
established relationship, the measured ultimate pullout load is used
to estimate the in place compressive strength of the concrete.
The equipments required for pull out test shall consist of the
following:
(a) Specially shaped steel rod or discs

(b) Dynamometer to apply the force
(c) Loading ram seated on a bearing ring for applying
pull out force
2.5.1 Object
The pull out test can be used to determine the following

properties.
(a) Compressive strength of concrete

(b) Normally planned for new structures to help decide,
whether critical activities such as form removal,
application of post tensioning etc. can be started
(c) Can be used for existing structures and surveys of
matured concrete
2.5.2 Principle
The pullout test measures the force required to pull an

embedded metal insert with an enlarged head from a concrete
specimen or a structure. The Fig 2.5.1 illustrates the configuration
of a pull out test. The test is considered superior to the rebound
hammer and the penetration resistance test, because large vol-
ume and greater depth of concrete are involved in the test. The
pull out strength is proportional to the compressive strength of
concrete. The pull out strength is of the same order of magnitude
(28)
Fig. 2.5.1 Configuration of Pull Out Test
as the direct shear strength of concrete, and is 10 to 30% of the

compressive strength. The pull out test subjects the concrete to
slowly applied load and measures actual strength property of the
concrete. The concrete is subjected, however, to a complex three
dimensional state of stress, and the pull out strength is not likely
to be related simply to uniaxial strength properties. Nevertheless,
by use of a previously established correlation, the pull out test can
be used to make reliable estimates of in situ strength.
2.5.3 Methodology
The pull out tests falls into two basic categories
(i) those in which an insert is cast along with concrete

i.e. the test is preplanned for new structures and
(ii) those in which insert is fixed by under cutting and
subsequent expanding procedure in the hardened con-
crete of existing structures.
These methods are generally known as “cast-in-method”

and “drilled hole method” respectively. There are various variants
in cast-in-methods like “LOK” test as well as in drilled hole method
(29)
like “CAPO” (cut and pull out). In the “CAPO” test method, an
expanding ring is fixed into an under reamed groove, producing a
similar pull out device to that used for “LOK”.
This insert is pulled by a loading ram seated on a bearing

ring that is concentric with the inner shaft. The bearing ring trans-
mits the reaction force to the concrete. As the insert is pulled out,
a conical-shaped fragment of concrete is extracted from the con-
crete mass. The idealized shape of extracted conic frustum is
shown in Fig 2.5.1. Frustum geometry is controlled by the inner
diameter of the bearing ring (D), the diameter of the insert head
(d), and the embedded depth (h). The apex angle (α) of the ideal-
ized frustum is given by
2 α = 2tan-1 D-d
2h
The ultimate pullout load measured during the in place

test is converted to an equivalent compressive strength by means
of a previously established relationship.
As per ASTM C-900-82, following are the requirements for

metal insert –
(a) Embedment depth 1.0d

(b) Bearing ring 2.0d to 2.4d
(c) Apex angle 53° to 70°
where d = insert head diameter
2.5.4 Advantages & Limitations
The relationship between pullout strength and compres-

sive strength is needed to estimate in place strength. Studies
suggested that for a given test system there is a unique relation-
ship. Therefore the recommended practise is to develop the
strength relationship for the particular concrete to be used in con-
struction. A large number of correlation studies have reported that
compressive strength is linear function of pull out strength.
The locations and number of pullout tests in a given place-

ment should be decided very carefully. The inserts should be
(30)
located in the most critical portions of the structure and sufficient

number of tests should be conducted to provide statistically sig-
nificant results.
The test is considered superior to the rebound hammer

and the penetration resistance test, because large volume and
greater depth of concrete are involved in the test.
2.5.6 Standards
The pull out test is conducted as per ASTM C 900-01 &

BS-1881 Part 207.
2.6 The Break-off Test
This test is a variant of the pull out test in which the flextural
strength of concrete is determined in a plane parallel to and at a
certain distance from the concrete surface. The break off stress
at failure can then be related to the compressive or flextural strength
of the concrete using a predetermined relationship that relates the
concrete strength to the break off strength.
The BO tester, consists of a load cell, a manometer and a

manual hydraulic pump capable of breaking a cylindrical concrete
specimen having the specified dimensions.
2.6.1 Object
This test can be used both for quality control and quality
assurance. The most practical use of the BO test method is for
determining the time for safe form removal and the release time for
transferring the force in prestressed post-tensioned members. This
test can be planned for new structures as well as for existing
structures.
2.6.2 Principle
The method is based upon breaking off a cylindrical speci-

men of in place concrete. The test specimen has a 55mm diam-
eter and a 70mm height. The test specimen is created in the
concrete by means of a disposable tubular plastic sleeve, which
(31)
is cast into the fresh concrete and then removed at the planned
time of testing, or by drilling the hardened concrete at the time of
the break off (BO) test. Fig 2.6.1 and 2.6.2 show tubular plastic
sleeves and a drill bit, respectively.
Fig. 2.6.1 Tubular Plastic Sleeves
Fig. 2.6.2 Drill Bit

Both the sleeve and the drill bit are capable of producing
a 9.5mm wide groove (counter bore) at the top of the test speci-
men (see Fig 2.6.3).A force is applied through the load cell by
means of a manual hydraulic pump. Fig 2.6.3 is a schematic of a
BO concrete cylindrical specimen obtained by inserting a sleeve
or drilling a core. The figure also shows location of the applied
load at the top of the BO test specimen. In principal, the load
configuration is the same as a cantilever beam with circular cross
section, subjected to a concentrated load at its free end. The force
required to break off a test specimen is measured by mechanical
manometer. The BO stress can then be calculated as:
(32)
Fig. 2.6.3 Schematic dig. of BO concrete specimen
fBO = M
S
where M = PBOh,
PBO = BO force at the top
h = 65.3 mm
S = dd
32
d = 55mm
In this case the cracks are initiated at the point 55mm

away from the concrete surface.
(33)
2.6.3 Methodology
The load cell has two measuring ranges: low range set-
ting for low strength concrete up to approx. 20 MPa and high range
setting for higher strength concrete up to abut 60Mpa. The equip-
ment used for this test is shown in Fig 2.6.4.
Fig. 2.6.4 Equipment for Break Off Test
A tubular plastic sleeve of diameter 55mm and geometry

shown in Fig. 2.6.1, is used for forming cylindrical specimen in
fresh concrete. A sleeve remover as shown in Fig. 2.6.5 is used
for removing the plastic sleeve from hardened concrete.
Fig. 2.6.5 Sleeve Remover
A diamond tipped drilling bit is used for drilling cores for

the BO test in hardened concrete (Fig. 2.6.2). The bit is capable
of producing a cylindrical core, along with a reamed ring (counter
bore) in the hardened concrete at the top with dimensions similar
(34)
to that produced by using a plastic sleeve.
The sleeves should be at center to center and edge dis-

tance of minimum 150mm. Concrete inside the sleeve and the
top of plastic sleeve itself should then be tapped by fingers to
ensure good compaction for the BO specimen. Sleeves should
then be moved gently up and down in place and brought to the
same level as the concrete surface at its final position. For stiff
mixes (i.e. low slump concrete) a depression may occur within
the confines of the sleeve during the insertion process. In such
cases the sleeve should be filled with additional concrete, tapped
with fingers. For high slump concrete, the sleeve may move up
ward due to bleeding. For such cases, sleeves should be gently
pushed back in place, as necessary, to the level of finished con-
crete surface. Grease or other similar material, should be used to
lubricate the plastic sleeves for its easier removal after the con-
crete hardens.
For core drilling from hardened concrete the concrete sur-

face should be smooth in order to fix the vaccum plate of the core
drilling machine. The core barrel should be perpendicular to the
concrete surface. The length of the drilled core should be 70mm
and in no case shorter than 70mm.
At the time of conducting BO test, remove the inserted

plastic sleeve by means of key supplied with the tester (Fig 2.6.5).
Leave the plastic ring in place. Remove loose debris from around
the cylindrical slit and the top groove. Select the desired range
setting and place the load cell in the groove on the top of the
concrete surface so that load is applied properly. The load should
be applied to the test specimen at a rate of approx. one stroke of
hand pump per second. After breaking off the test specimen,
record the BO manometer reading. The BO meter reading can
then be translated to the concrete strength using curves relating
the BO reading to the desired concrete strength.
Before conducting the test, the BO tester should be cali-

brated as per the procedure given by the manufacture. The BO
manufacturer provides correlation curves relating the BO reading
and the compressive strength of the standard 150mm cubes.
(35)
However, it is desireable that the user should develop his own

correlation curves for a particular concrete batch. Developing cor-
relation curves for different types of concrete would increase the
accuracy and dependability of method in predicting the in-place
strength. The following precaution should be taken when develop-
ing data for correlations:
(a) keep the center-to-center and edge distance of at least 150mm
in the process of inserting sleeves or drilling
(b) obtain a minimum of 5 readings and three corresponding
strength test specimens values i.e. cubes for compressive
strength, and beams for flextural strength, for each test age.
(c) An average of the five BO readings and the average of the
three standard cube test results represent one point on the
graph relating the BO reading to the desired standard strength
of the concrete.
(d) Cover the range of concrete strengths expected during ex-
ecution of the project, at early as well as later stages, such
as 1,3,5,7,14 and 28 days.
The main advantage of BO test is that it measures in-

place concrete (flextural) strength. The equipment is simple and
easy to use, the test is fast to perform, requiring only one ex-
posed surface. The BO test does not need to be planned in ad-
vance of placing the concrete because drilled BO test specimen
can be obtained.
The two limitations of this test are :

(i) the max. aggregate size and
(ii) the minimum member thickness for which it can be used.
The max. aggregate size is 19mm and min. member thick
ness is 100mm. However, the principle for the method
can be applied to accommodate large aggregate sizes or
smaller members. The test cause the damage to the con
crete which needs repair after conducting the test.
2.6.5. Standards
The break off test is conducted as per ASTM C 1150.

(36)
2.7 Penetration Resistance Methods
Amongst the penetration methods presently available, the

most well known and widely used is Windsor Probe test. Pen-
etration resistance methods are based on the determination of the
depth of penetration of probes (steel rods or pins) into concrete.
This provides a measure of the hardness or penetration resistance
of the material that can be related to its strength.
The Windsor probe consists of powder – actuated gun or

driver, hardened alloy steel probes, loaded cartridges, a depth gauge
for measuring the penetration of probes and other related equip-
ment (Fig. 2.7.1).
Fig. 2.7.1 Windsor Probe
The probes have a tip dia of 6.3 mm, a length of 79.5mm, and a
conical point. Probes of 7.9mm dia are also available for the test-
ing of concrete made with light weight aggregates.
2.7.1 Object
The Windsor probe test is used to determine

(a) Compressive strength of in situ concrete
(b) For ensuring quality control
(c) For determining safe form removal time
(d) The uniformity of concrete and to delineate zones of poor
quality or deteriorated concrete in structures.
(37)
2.7.2 Principle
The Windsor probe, like the rebound hammer, is a hardness

tester, and the penetration of probe can be related to the
compressive strength of concrete below the surface, using
previously developed correlations between strength properties and
penetration of the probe. The underlying principal of this penetration
resistance technique is that for standard test conditions, the
penetration of probe in to the concrete is inversely proportional to
the compressive strength of the concrete. In other words larger
the exposed length of the probe, greater the compressive strength
of concrete.
2.7.3 Methodology
The method of testing is simple and is given in the manual

supplied by the manufacturer. The area to be tested must have a
smooth surface. To test structure with coarser finish, the surface
must be first ground smooth in the area of the test. The powder
actuated driver is used to drive a probe into concrete. If flat surfaces
are to be tested, a suitable locating template to provide 158mm
equilateral triangular pattern is used and three probes are driven
into the concrete at each corner. The exposed length of individual
probes are measured by a depth gauge. For testing structures
with curved surfaces, three probes are driven individually using the
single probe locating template. In either case, the measured
average value of exposed probe length may then be used to
estimate the compressive strength of concrete by means of
appropriate correlation data.
The manufacturer of the Windsor probe test system supply

tables relating exposed length of the probe with compressive
strength of concrete. For each exposed length value, different
values of compressive strength are given, depending upon the
hardness of aggregate. However the manufacturer’s table do not
always give satisfactory results. Sometimes they considerably
over estimate the actual strength and in some cases they
underestimate the strength. It is, therefore, imperative to correlate
probe test result with the type of concrete being used. In addition
to hardness of the coarse aggregate, the type and size of coarse
(38)
aggregate also have a significant effect on probe penetration. The

degree of carbonation and the age of concrete may also affect the
probe penetration strength relationship.
Windsor probe testing method is basically hardness

method, and like other hardness methods, should not be expected
to yield absolute values of strength of concrete in a structure.
However, like surface hardness tests, penetration tests provide an
excellent means of determining the relative strength of concrete in
the same structure, or relative strength in different structures.
One of the limitation of this test is minimum size

requirements for the concrete member to be tested. The minimum
distance from a test location to any edges of the concrete member
or between two given test locations is of the order of 150mm to
200mm, while the minimum thickness of the member is about
three times the expected depth of penetration. The test also causes
some minor damage to the surface, which generally needs to be
repaired.
The main advantages of this test are the speed and

simplicity and only one surface is required for testing.
2.7.5. Standards
The penetration resistance test is coducted as per ASTM

C 803 / C 803-03 and BS 1881 Part 207.
CHAPTER-3
NON–DESTRUCTIVE TESTS FOR CORROSION

ASSESSMENT, LOCATION AND DIAMETER OF
REINFORCEMENT AND COVER THICKNESS OF
CONCRETE BRIDGES
3.1 Introduction
For effective inspection and monitoring of concrete bridges,

the condition assessment of reinforcement is an important step.
Even for deciding appropriate repair strategy for a distressed
concrete bridge, the determination of corrosion status of reinforcing
bars is a must. Most of NDT methods used for corrosion
assessment are based on electrochemical process. But apart
from the process, it is advisable that the persons involved for
conducting the tests should have enough experience in this
particular field. The following methods are normally used for the
condition assessment of reinforcement in concrete structures :
(a) Half cell Potential Measurement (Corrosion Analyzing
Instrument)
(b) Resistivity test
(c) Test for carbonation of concrete
(d) Test for chloride content of concrete
The following methods are generally used for determining

the location / diameter of reinforcement bars and cover thickness
in concrete bridges
(a) Profometer
(b) Micro covermeter
Each of the above said methods has been discussed in

detail in this chapter.
3.2 Half-cell Potential Measurement Method
When there is active corrosion, current flow through the

concrete between anodic and cathodic sites is accompanied by
(40)
an electric potential field surrounding the corroding bar. The

equipotential lines intersect the surface of the concrete and the
potential at any point can be measured using the half potential
method. Apparatus for half cell potential measurement is shown in
Fig.3.2.1.
Fig. 3.2.1 Apparatus for Half-Cell Potential Measurement
The apparatus includes copper-copper sulphate half-cell,

connecting wires and a high impedance voltmeter. This half-cell is
composed of a copper bar immersed in a saturated copper sulphate
solution. It is one of the many half cells that can be used as a
reference to measure the electrical potential of embedded bars. A
high impedance voltmeter (normally greater than 10MW) is used
(41)
so that there is very little current through the circuit. The copper-
copper sulphate half-cell makes electrical contact with the concrete
by means of porous plug and a sponge that is moistened with a
wetting solution (such as liquid detergent).
One of the instrument available in the market is CANIN

corrosion analyzer, which is a computer based device for making
half cell potential measurement. This particular instrument stores
data acquired at different test points and display equipotential
contours.
3.2.1 Object
This test is used to assess the corrosion conditions in a

reinforced concrete structure. The method detects the likelihood
of corrosion of steel but can not indicate the rate of corrosion. By
making measurements over the whole surface, a distinction can
be made between corroded and non-corroded locations.
3.2.2 Principle
CANIN corrosion analyzer is based on electro-chemical

process to detect corrosion in the reinforcement bars of structure.
It represents a galvanic element similar to a battery ,producing an
electrical current, measurable as an electric field on the surface of
concrete. The potential field can be measured with an electrode
known as half cell. The electrical activity of the steel reinforcement
and concrete leads them to be considered as one half of battery
cell with the steel acting as one electrode and concrete as
electrolyte. The name half cell surveying derives from the fact that
the one half of the battery cell is considered to be the steel
reinforcing bars and surrounding concrete. The electrical potential
of a point on the surface of steel reinforcing bar can be measured
comparing its potential that of copper – copper sulphate reference
electrode/silver- silver nitrate reference electrode on the surface.
The positive terminal of the voltmeter is attached to the

reinforcement and the negative terminal is attached to the copper-
copper sulphate half cell. If there is any corrosion in the bars, the
excess electrons in the bar would tend to flow from the bar to the
(42)
half cell. Because of the way the terminals of the voltmeter are
connected in the electrical circuit (Fig. 3.2.1), the voltmeter
indicates a negative voltage. The measured half cell potential is
the open circuit potential, because it is measured under the
condition of no current in the measuring circuit. A more negative
voltage reading at the surface is to interpreted to mean that the
embedded bar has more excess electrons, and there is, therefore,
a higher likelihood that the bar is corroding.
The half cell potential readings are indicative of the

probability of corrosion activity of the reinforcing bars located
beneath the copper-copper sulphate reference cell. However, this
is true only if the reinforcing steel is electrically connected to the
bar attached to the voltmeter.
3.2.3 Methodology
The corrosion analyzing instrument CANIN operates as

digital voltmeter. Voltage of + 999 mV DC can be measured using
this instrument. The potential in millivolts is measured with rod
electrodes at different locations on the structure. The measured
voltage depends upon the type of the half-cell, and conversion
factors are available to convert readings obtained with other half
cells to copper-sulphate half cell.
Testing is usually performed at points arranged in a grid.

The required spacing between test points depends on the particular
structure. Excessive spacing can miss points of activity or provide
insufficient data for proper evaluation, while closer spacing increase
the cost of survey. In surveying bridge decks, ASTM C 876
recommends a spacing of 1.2 meter. If the difference in voltage
between adjacent points exceed 150 mV, a closer spacing is
suggested. A key aspect of this test is to ensure that the concrete
is sufficiently moist to complete the circuit necessary for a valid
measurement. If the measured value of the half cell potential varies
with time, pre wetting of the concrete is required. Although pre
wetting is necessary, there should be no free surface water between
test points at the time of potential measurement. The concrete is
sufficiently moist if the measured potential at a test point does not
change by more than + 20 mV within a 5 min. period. If stability
(43)
cannot be achieved by pre-wetting, it may be because of stray

electrical currents or excessive electrical resistance in the circuit.
In either case, the half cell potential method should not be used.
Testing should be performed between temperature range of 17 to
280C.
3.2.4 Interpretation of test results
As per ASTM C 876, two techniques can be used to

evaluate the results (i) the numeric technique (ii) the potential
difference technique.
In the numeric technique, the value of the potential is used

as an indicator of the likelihood of the corrosion activity. The
potential measured at the surface of concrete can be interpreted
as per table given below:-
Phase of Corrosion Activity Potential as measured by

Copper Half Cell
1. Initial Phase – Corrosion < - 200 mV
activity not taking place
2.Transient Phase – Corrosion - 200 mV to - 350 mV
activity uncertain
3. Final phase – corrosion > - 350 mV
occurring positively
Source: Appendix of ASTM C 876
The numeric method should not be used in the following

conditions –
(a) Carbonation extends to the level of reinforcement

(b) Comparison of corrosion activity in outdoor
concrete with highly variable moisture or oxygen
content.
(c) Evaluation of indoor concrete that has not been
subjected to frequent wetting.
(44)
(d) To formulate conclusions about changes in

corrosion activity due to repairs which changed
the moisture or oxygen content at the level of the
steel.
In the potential difference technique, the areas of active

corrosion are identified on the basis of the potential gradients. In
the equipotential contour plot, the closer spacing of the voltage
contour indicates regions of high gradients. The higher gradient
indicates, higher risk of corrosion.
The potential difference technique is considered more

reliable for identifying regions of active corrosion than is the use of
numerical limits.
3.2.5 Limitations
For conducting this test access to the reinforcement is

must. The method cannot be applied to epoxy coated
reinforcement or concrete with coated surfaces. The concrete
should be sufficiently moist for conducting this test.
This test only indicates the liklyhood of corrosion activity

at the time of measurement. It does not furnish direct information
on the rate of corrosion of the reinforcement.
3.2.6 Standards
This method is covered under ASTMC 876-91 (Reapproved

1999).
3.3 Resistivity Test
This test is used to measure the electrical resistance of

the cover concrete. Once the reinforcement bar loses its passivity,
the corrosion rate depends on the availability of oxygen for the
cathodic reaction. It also depends on the concrete, which controls
the ease with which ion migrate through the concrete between
(45)
anodic and cathodic site. Electrical resistance, in turn, depends

on the microstructure of the paste and the moisture content of the
concrete.
The combination of resistance measurement by

resistivity meter and potential measurement by corrosion
analyzing instrument give very reliable information about the
corrosion condition of the rebar.
The equipment used for this test is a portable, battery

operated, four probe device which measures concrete resistivity.
( Fig. 3.3.1)
Fig. 3.3.1 Resistivity Meter
3.3.1 Object
This test is used to assess the probability or likelihood of

corrosion of the reinforcement bar. The resistivity increases as
the capillary pore space in the paste is reduced. So high resistivity
also indicates the good quality of concrete.
3.3.2 Principle
The corrosion of steel in concrete is an electrochemical

process, which generates a flow of current and can dissolve metals.
(46)
The lower the electrical resistance, the more readily the corrosion
current flows through the concrete and greater is the probability of
corrosion. The resistivity is numerically equal to the electrical
resistance of a unit cube of a material and has units of resistance
(in ohms) times length. The resistance (R) of a conductor of area
A and length L is related to the resistivity ρ as follows:
R=ρL
A
The schematic diagram showing the set up for
measurement of concrete resistivity is shown in Fig. 3.3.2.
Fig. 3.3.2 Setup for Measurement of concrete resistivity
This is based on the classical four electrode system in

which four equally spaced electrodes are electrically connected
to the concrete surface. The outer electrodes are connected to a
source of alternating current, and the two inner electrodes are
connected to voltmeter.
(47)
3.3.3 Methodology
One of commercial equipment available for measurement

of resistivity is Resistivity Meter which is a four probe device used
for measuring resistivity. The set of four probes are fitted with
super conductive foam tips to ensure full contact on irregular
surfaces. Once the probes are kept in contact with the concrete
surface, the LCD display will indicate the resistivity directly on the
screen. The limits of possible corrosion are related with resistivity
as under:
1. With ρ =12 K W cm Corrosion is improbable
2. With ρ = 8 to 12 K W cm Corrosion is improbable
3. With ρ = 8 K W cm Corrosion is fairly certain
where ρ (rho) is the resistivity
3.3.4 Limitations
The method is slow because it covers small area at a

time. The system should not be used in isolation because it gives
better indication of corrosion in reinforced concrete if used in
combination with half - cell potentiometer.
3.4 Tests for carbonation of Concrete
Carbonation of concrete in cover results in loss of protection

to the steel against corrosion. The depth of carbonation can be
measured by spraying the freshly fractured concrete surface with
a 0.2% solution of phenolphthalein in ethanol. Since
phenolphthalein is a pH indicator, the magenta (pink colour) area
presents uncarbonated concrete and the remaining (colourless)
portion, the carbonated area. The change in colour occurs at
around pH 10 of concrete.
The test must be applied only to freshly exposed surfaces,

(48)
because reaction with atmospheric carbon dioxide starts

immediately. Relating carbonation depth to concrete cover is one
of the main indicators of corrosion.
3.5 Test for chloride content of concrete
The presence of chloride in the concrete is the contributory

factor towards corrosion of reinforcement.
Portable equipments are available in the market, which

can be used for rapid on site measurement of chloride content of
concrete. The chloride content of concrete can also be determined
by chemical analysis of concrete in the laboratory.
A rotary percussion drill is used to collect a pulverized

sample of concrete and a special acid extracts the chlorides. The
amount of acid soluble chloride is determined directly by a chloride
sensitive electrode connected to a electrometer.
If different samples are obtained from different concrete

depths, it can be established whether the chloride contamination
was there in the original concrete or the same has come from the
environment.
3.6 Profometer
In any RCC/PSC structure, adequate cover thickness is

essential to prevent corrosion of the reinforcement. In old
structures, sometimes the detailed drawings are not traceable due
to which it becomes very difficult to calculate the strength of the
structure which is essentially required for finalizing the strengthening
scheme. Sometimes, the bridges are to be checked from strength
point of view to permit higher axle load and in absence of
reinforcement details it becomes very difficult to take a decision.
To overcome all these problems, the methods have been

developed for investigation and evaluation of concrete structures.
Profometer is a small versatile instrument for detecting location,
size of reinforcement and concrete cover. This instrument is also
(49)
known as rebar locator. This is a portable and handy instrument

which is normally used to locate the reinforcement on LCD display.
This instrument is available with sufficient memory to store
measured data. Integrated software is loaded in the equipment for
carrying out and printing statistical values. One of the equipment
which is commercially available in the market is shown in
Fig. 3.6.1.
Fig. 3.6.1. Profometer
The equipment is quite handy and weighing less than two

kgs. It works on normal batteries and thus does not require any
electrical connection.
3.6.1. Object
This test is used to assess the location and diameter of

reinforcement bars and concrete cover. This equipment can be
used effectively for evaluation of new as well as old structures. The
method can be used both for quality control as well as quality
assurance.
3.6.2. Principle
The instrument is based upon measurement of change of

an electromagnetic field caused by steel embedded in the concrete.
(50)
3.6.3. Methodology
To ensure satisfactory working of profometer and to get

accurate results, it should be calibrated before starting the
operations and at the end of the test. For this purpose, test block
provided with the instrument should be used. To check the
calibration accuracy, the size and cover of the reinforcement of
the test block is measured at different locations on test block and
the recorded data should match with the standard values prescribed
on the test block.
Path measuring device and spot probes are together used

for path measurements and scanning of rebars. These are
connected with profometer with cables and are moved on the
concrete surface for scanning the rebars and measuring the spacing.
As soon as the bar is located, it is displayed on the screen. Once
the bar is located, it is marked on the concrete surface.
Diameter probe is used for measuring the dia of bars. It is

also connected with profometer by one cable. After finding out the
location of rebar, the dia probe is placed on the bar parallel to bar
axis. Four readings are displayed and mean value of these readings
is taken as diameter of bar.
Depth probe of the profometer is used to measure the

cover. It is also connected with profometer by cable and is placed
exactly on the bar As soon as, the depth probe is above a rebar or
nearest to it, it gives an audio signal through a short beep and
visual display. Simultaneously, the measured concrete cover is
stored in memory.
For carrying out this test, the proper assess is essential.

For this purpose, proper staging, ladder or a suspended platforms
may be provided. Before actual scanning, marking is done with
chalk on the concrete surface by dividing it into panels of equal
areas.
(51)
3.6.4. Advantages and Limitations
This is a purely non-destructive test for evaluation of

concrete structure particularly old structures. The methods is
very fast and gives quite accurate results if the reinforcement is
not heavily congested. The equipment is very light and even one
person can perform the test without any assistance.
The equipment is not being manufactured in India and

needs to be imparted. Some of the Indian Firms are marketing
the instrument and this is a costly equipment.
3.7. Micro covermeter
This is a portable and handy instrument weighing about0.5

kg. This is normally provided with two types of search heads one
for parallel bars having range approx. 360mm and other for mesh
and close spaced bars having range of approx. 120mm. It can
function over the temp. range of 0°C to 45°C. One of the micro
cover meter commercially available in the market is shown in Fig.
3.7.1.
Fig. 3.7.1. Micro Covermeter

(52)
The equipment is of 180mm x 100mm x 45mm size

approximately. The equipment is available with volatile memory
that helps in storing data while taking measurements.
3.7.1. Object
The test is aimed mainly to detect the location and cover

of reinforcement. The test may be used for analyzing the integrity
of the structures as the cover thickness is an important aspect of
construction. In the coastal areas, the test can be used for deciding
the effectiveness of cover as well as rehabilitation measures
required.
3.7.2 Principle
The equipment consists of a highly permeable U-shape

magnetic core on which two coils are mounted. When an
alternating current is passed through one of these coils, the current
induced in the other coil can be measured. The presence of steel
affects the electromagnetic field. The induced current depends
upon the mutual inductance of the coils and the nearness of the
steel bars. A moving coil meter measures the current. For
measurement of the cover, the probe is placed directly over the
concrete member and moved slowly until reading is obtained on
the dial. The probe should be kept parallel to the length of rebar.
Depending upon the diameter of the bar, the dial readings gives
directly the cover to the reinforcement.
3.7.3. Methodology
The equipment should be calibrated before starting and at

the end of the test to get accurate results. For this purpose, one
spacer is provided with each equipment. For calibration, the cover
should be measured at one location and then it is remeasured
after placing the spacer between the concrete surface and probe.
The difference between two readings should not vary more than
+/- 5% of the thickness of the spacer.
For locating the reinforcement bar, the search head should

be placed on the surface of concrete in such a way so that the
(53)
length of the search head should be parallel to the reinforcement

provided in the structure. The location of the main reinforcement
should be decided based upon the geometry of the structure. The
search head should be moved from one end to other end in a
direction perpendicular to the main reinforcement. The sound of
the buzzer /beep will be strongest when the bar will come just
above or below the probe.
For measurement of cover, the search head is moved on

the surface. While moving, the cover displayed on the screen
reduces and sound of the buzzer/beep increases when probe
comes near reinforcement bars. The minimum reading displayed
will be the cover and the sound of the buzzer is strongest when
the reinforcement bar is just below the search head.
3.7.4. Advantages and Limitations
The method is very fast and large area can be covered

within short time. The instrument work on batteries and does not
require any electric supply. Since the equipment is very small
and portable, the test can be conducted by single person without
any assistance.
CHAPTER 4
NON-DESTRUCTIVE TESTS FOR DETECTION OF

CRACKS/VOIDS/ DELAMINATIONS ETC.
IN CONCRETE BRIDGES
4.1 Introduction
For the assessment of the actual condition of a concrete

bridge, the detection of internal crack, void, lamination etc. is very
much necessary. The NDT methods for testing surface hardness,
strength and for checking the condition of reinforcement do not
indicate the internal condition of concrete. Sometimes these
internal cracks, voids etc. may lead to the corrosion of
reinforcement, cracking of section which may ultimately result into
reduced life of bridge. The following methods are normally used
for detection of cracks/voids/laminations etc. in concrete bridges
–
(i) Infrared thermographic techniques

(ii) Acoustic Emission technique
(iii) Short pulse radar methods
(iv) Stress wave propagation methods
Some of these methods are used extensively all over the

world for condition assessment of various components of concrete
bridges while some methods are still in the laboratory trial stage.
All the above methods are discussed in detail in this chapter.
4.2 Infrared thermographic techniques
For conducting this test, high resolution infrared

thermographic radiometers (Fig. 4.2.1) are used to inspect large
areas of concrete efficiently and quickly. This type of equipment
allows larger areas to be scanned, and the resulting data can be
displayed as pictures with areas of differing temperatures
designated by differing grey tones in black and white image or by
various colours on a colour image. A complete thermographic
(55)
Fig. 4.2.1 Infrared Thermographic Radiometer
data collection and analysis system can be divided into four main
subsystems. The first is the infrared sensor head that normally
can be used with interchangeable lenses. It is similar in appearance
to a portable video camera.
The second major component of the infrared scanning

system is a real-time microprocessor coupled to a black-and-white
or colour display monitor. With this, component, cooler items
being scanned are normally represented by darker grey ones, and
warmer areas are represented by lighter gray tones. Now-a-days,
colour monitors are also used, which displays the different
temperature levels as contrasting colours and patterns, which are
easier to decipher.
The third major component of the infrared scanning system

is the data acquisition and analysis equipment. It is composed of
an analog-to-digital converter for use with analog sensors, a
computer with a high resolution colour monitor, and data storage
and analysis software.
The fourth major component consists of various types of

image recording and retrieving devices. These are used to record
both visual and thermal images.
(56)
4.2.1 Object
This technique can be used to detect concrete subsurface

delamination on bridge decks. This can also detect the internal
voids, cracks and honeycombing in concrete structures. This
method gives the fairly accurate picture about the condition of
concrete inside and can be effectively applied for larger surfaces.
4.2.2 Principle
Infrared thermographic investigation techniques are based

on the principle that the materials with subsurface anomalies, such
as voids caused by corrosion of reinforcing steel, or voids caused
by poor compaction called honeycombing, in a material affect heat
flow through that material. These changes in heat flow cause
localized differences in surface temperatures. Thus, by measuring
surface temperatures under conditions of heat flow into or out of
the material, one can determine the presence and location of any
subsurface anomalies.
An infrared thermographic scanning system measures

surface temperature only, but the surface temperatures of a
concrete mass depend on three factors.
(a) The subsurface configuration

(b) The surface conditions
(c) The environment
Normally the testing should be conducted during times of

the day or night when the solar radiation or lack of solar radiation
would produce the most rapid heating or cooling of the concrete
surface. The test should not be conducted when sky is cloudy.
The measurements should be taken when then wind speed is lower
than 25kmph. The test should not be conducted when the
temperature is below 0°C. If the concrete surface is covered with
standing water, the test should not be conducted.
4.2.3 Methodology
For performing this test efficiently, a movement of heat

(57)
must be established in the structure. Normally the inspection

should be conducted during the sunny day, i.e. the testing should
be avoided during monsoon. The inspection may begin either 2 to
3 hours after sunrise or 2 to 3 hours after sunset, both are times of
rapid heat transfer. The surface to be tested should be cleaned
thoroughly.
The next step is to locate a section of sound concrete.

This work can be done by chain dragging (sounding), coring, or
ground penetrating radar or by using some other suitable method.
Image the reference area and set the equipment controls so that
an adequate temperature image is viewed and recorded.
The next step is to image the area, which is known to

have defects i.e. voids/delamination/cracks etc. and images of
this defective area are viewed and recorded. Now the setting of
the equipment should be done in such a way to allow viewing of
both the sound and defective reference areas in the same image
with the widest contrast possible.
If a black and white monitor is used, better contrast images

will normally be produced when the following convention is used,
black is defective concrete and white is sound material. If a colour
monitor or computer enhanced screen is used, three colours are
normally used to designate definite sound areas, definite defective
areas and indeterminate areas. When tests are performed during
day light hours, the defective concrete areas will appear warmer,
whereas during test performed after dark, defective areas will appear
cooler.Once the control are set, the recording of images can be
done and stored.
The main advantage of this method is that it is an area

testing technique, whereas other destructive and non-destructive
methods are points testing or line testing methods. This method
is completely non-destructive, repeatable, accurate, efficient and
economical. The method can cover large areas within short time.
One of the biggest advantage of this method is that this is absolutely
safe and equipment does not emit any radiation.
(58)
The main limitation is that the depth or thickness of a void

cannot be determined using this method. It cannot be determined
whether a subsurface void is near the surface or away from the
surface. When used in combination with ground penetrating radar
method this method gives useful information about the internal
defects.
4.3 Acoustic Emission Technique
Acoustic emission is the sound (both audible and

sub-audible), that are generated when a material undergoes
irreversible changes, such as those due to cracking. In general,
acoustic emissions are defined as the class of phenomena whereby
transient elastic waves are generated by the rapid release of energy
from localized sources within a material. These wave propagate
through the material, and their arrival at the surface can be detected
by the piezoelectric transducers.
The main elements of a modern acoustic emission

detection system are shown in Fig. 4.3.1.
The brief description of the most important parts of this

system is as follows:
a) Transducers – Piezoelectric transducers (generally made

of lead zirconate titanate, PZT) are used to convert the surface
displacements into electric signals. There are mainly two types
of transducers – wide band transducers and narrow band
transducers. The transducers must be properly coupled to the
specimen, often using some form of silicon grease as the coupling
medium.
(b) Preamplifier – Because of the low voltage output, the leads

from the transducer to the preamplifier must be as short as possible.
Sometimes the preamplifier is integrated within the transducer itself.
This amplifies the output signals.
(c) Passband filters – These are used to suppress the acoustic

emission signals that lie outside the frequency range of interest.
oscilloscope
audio amplifier
pulse counter and speaker
threshold
discrimination
event counter
main
amplifier signal duration display
maximum printer
bandpass amplitude
filter
energy Plotter
(59)
preamplifier
frequency cassette computer
analysis recorder
transducers aplitude
distribution
defect
specimen location
signal analysis
Fig. 4.3.1 Elements of Modern Acoustic Emission Detection System

(60)
(d) Main amplifier - This further amplifies the signals, typically

within a gain of 20 to 60 dB.
(e) The discriminator – It is used to set the threshold voltage

above which signals are counted.
4.3.1 Object
This method is used mainly to detect the cracking in

concrete, whether due to externally applied loads, drying shrinkage
or thermal stresses. This method can be helpful in determining
the internal structure of the material and to know the structural
changes during the process of loading.
The method can also be used to establish whether the

material or the structure meet certain design or fabrication criteria.
In this case, the load is increased only to some predetermined
level. The amount and nature of acoustic emissions may be used
to establish the integrity of the specimen or structure and may
also be used to predict the service life.
4.3.2 Principle
When an acoustic emission event occurs at a source with

the material, due to inelastic deformation or cracking, the stress
waves travel directly from the source to the receiver as body waves.
Surface waves may then arise from mode conversion. When the
stress waves arrive at the receiver, the transducer responds to the
surface motion that occurs. A typical acoustic emission signal
from concrete is shown in Fig. 4.3.2.
By using a number of transducers to monitor acoustic

emission events, and determining the time differences between
the detection of each event at different transducer positions, the
location of acoustic emission event may be determined by using
triangulation techniques.
(61)
Fig. 4.3.2 Acoustic Emission Signal from concrete
4.3.3 Methodology
Acoustic emission test may be carried out in the

laboratory or in the field. Basically one or more acoustic emission
transducers are attached to the specimen. The specimen is then
loaded slowly, and the resulting acoustic emissions are recorded.
The test is generally conducted in two ways.
(a) When the specimens are loaded till failure. (to know
about internal structure/to study about structural
changes during loading)
(b) When the specimens are loaded to some
predetermined level (to ascertain whether the material
or structure meet certain design or fabrication criteria).
4.3.4 Limitations
The acoustic emission techniques may be very useful in

the laboratory to supplement other measurement of concrete
properties. However, their use in the field is still very limited. Another
draw back is that acoustic emissions are only generated when
the loads on a structure are increased and this create considerable
practical problems.
(62)
4.4 Short Pulse Radar Method
Short Pulse radar systems are used in applications related

to inspection of concrete. This is the electromagnetic analog of
sonic & ultrasonic pulse echo methods. In this method, the electro
magnetic waves propagates through materials of different dielectric
constants.
A basic radar system consists of a control unit, a

monostatic antenna (i.e. an antenna that is used for both
transmitting & receiving) , an oscillograph recorder, and a power
convertor for DC operation. ( see Fig. 4.4.1)
Fig.4.4.1 Short Pulse Radar System
For inspection of concrete structures, it is desirable to

use a radar antenna with relatively high resolution or short pulse
width.
4.4.1 Object
The method can be effectively used for detection of

delamination in concrete. The method can also be used for
determination of degree of hydration of concrete, water content in
fresh concrete, and for measurement of concrete layer thickness
etc. Method can also be used for locating the position of rebars.
(63)
4.4.2 Principle
When an electromagnetic wave (such as microwave) strike

an interface, or boundary between two materials of different
dielectric constants, a portion of the energy is reflected and the
remaining penetrates through the interface into the second material
( Fig. 4.4.2 )
Fig. 4.4.2 Movment of Electromagnetic Wave
The intensity of reflected energy (AR), is related to the intensity

of the incident energy (AI) by the following relationship -
AR η 2 − η1
ρ 1, 2 = = ........(1)
AI η 2 + η1
Where ρ1, 2 is the reflection coefficient at the interface,

& are the wave impedances of the material 1,2 respectively,
in ohms. For non-metallic material, such as concrete or soil the
wave impedance is given by
……(2)
(64)
where is the magnetic permeability of air, which is 4

x10-7 henry /meter and is the dielectric constant of material in
farad / meter
Since the wave impedance of air, is equal to
where is dielectric constant of air which is

8.85 x 10-12 farad/meter.
If we define the relative dielectric constant of a material as
Then the equation (2) can be written as
and equ. (1) can be written as
………….(3)
where and are the relative dielectric constants of material

1 an 2 respectively.
So depending upon the relative dielectric constants of

material 1 and 2, the amount of reflected energy from interface of
material 1 &2 is determined, and the remaining energy will be
penetrated into material 2. When this remaining microwave en-
ergy reaches another interface after traveling to material 2, a
portion will be reflected back as shown in equation (3).
This reflection of energy from various interfaces is being

(65)
measured in Short Pulse Radar method for determination of vari-

ous defects.
4.4.3 Methodology
For inspection of concrete bridges, an antenna is placed

with its transmitting face parallel to and at a distance from the
surface of the concrete. However, if the concrete member is rela-
tively thick and the expected deterioration is deep or if the an-
tenna does not have sufficient power or penetration, the antenna
may be placed directly over the concrete surface. With the ad-
justments in the control unit the radar signals are recorded with a
properly calibrated oscillograph recorder. This is called the static
mode of measurement, since the antenna is stationary with re-
spect to the concrete being tested.
If relatively large concrete area has to be inspected the

antenna is mounted on the front or rear of an inspection vehicle.
The vehicle will make several passes over the area to be tested to
cover the entire area. During each pass the antenna scans a
different area. The stream of the radar signals are recorded con-
tinuously with an instrumentation tape recorder. With two antenna
or multi antenna system, the requirement of number of passes will
be less. These recordings are later on studied and interpreted for
detection of defects.
This methods is very much effective for inspection of deck

slab of road bridges, provided with asphalt overlays. The distruption
to road traffic is minimal while inspection is done. There are no
restrictions, regarding the timing of inspection or the availability of
certain ambient conditions during inspections and inspection can
be done any time and in any type of ambient conditions.
The major limitation is that the interpretation of signals
received at radar is very cumbersome because of the presence of
interfering signals.
4.5 Stress Wave Propagation Methods
There are several test methods, based on stress wave

(66)
propagation, used for non-destructive testing of concrete. The

echo methods (impact echo and pulse echo) are used for thick-
ness measurements, flaw detection and integrity testing of piles.
The impulse response method is also used to test piles and slab
like structures. The following stress wave propagation method are
generally used for testing of concrete.
(a) Pulse Echo method

(b) Impact Echo method
(c) Impulse response method
All the three methods are discussed in detail in this chapter.
4.5.1 Pulse Echo method
In this method, a transmitter introduces a stress pulse

into an object at an accessible surface. The pulse propagates
into the test object and is reflected by flaws or interfaces. The
surface response caused by the arrival of reflected waves, or ech-
oes, is monitored by either the transmitter acting as a receiver
(true pulse echo) or by a second transducer located near the pulse
source (pitch-catch). (Fig. 4.5.1.)
Fig. 4.5.1 Pulse Echo Methods

(67)
The output is displayed on a display device and the dis-

play is called a time domain waveform. By using the time base of
display, the travel time of the pulse is determined. If the wave
speed in the material is known, this travel time can be used to
determine the depth of the reflecting interface using the
following equation:.
T = ½ ∆t Cp
Where, ∆t = the round trip travel time
T = the depth
Cp = the wave speed
The main components of a pulse echo or pitch catch test

system are the transmitting and receiving transducer and the sys-
tem that is used to record and display wave forms. For testing
concrete, low frequency transducers are required. Because of the
practical problem of manufacturing large size transducers, the pulse
echo technique is not used for testing of concrete in the field.
4.5.2 Impact Echo Method
This method is normally used for testing of piles. The

principle of impact echo technique is illustrated in Fig. 4.5.2.
Fig. 4.5.2 Impact Echo Technique

(68)
A stress pulse is introduced into a test object by me-

chanical impact on the surface. The stress pulse propagates into
the object along spherical wave fronts as P and S waves. In addi-
tion a surface wave (R-Wave) travels along the surface away from
the impact point. P-Wave is a compression wave and S-wave is
a shear wave. In P-wave particle motion is parallel to the
propagation direction while in S-wave particle motion is perpen-
dicular to the propagation direction. R-wave or surface wave,
propagates along the surface of a solid, and particle motion is
retrograde elliptical.
The P and S stress waves are reflected by internal inter-

faces or external boundaries. The arrival of those reflected waves,
or echoes, at the surface where the impact was generated pro-
duce displacements that are measured by a receiving transducer
and recorded by a data acquisition system.
An impact echo test system is composed of three com-

ponents i.e. an impact source, a receiving transducer and a data
acquisition system with appropriate software for signal analysis
and data management. The selection of the impact source is a
important aspect of a successful impact echo test system. The
lesser the contact time, the higher the range of frequencies. As
the contact time decreases, smaller size defects can be detected.
For testing of slabs etc. shorter contact time is preferable. How-
ever, for piles and other slender members, longer contact time is
preferable.
The test method is covered under ASTM C 1383.
4.5.3 Impulse Response method
This is another variant of impact method. This method is

also known as transient dynamic response or impedance testing.
This works on the same principle as impact echo method. A stress
pulse is generated by mechanical impact on the surface of the
object. The force time function of the impact is monitored by
using an instrumented hammer or by using a hammer to strike a
load cell. A transducer located near the impact location monitors
(69)
the movement of the surface as it vibrates in response to the im-

pact. The waveforms of the force and motion transducers are
recorded and processed on a dynamic signal analyzer or com-
puter with appropriate software. The result of the analysis indi-
cates the condition of the structure.
The impulse response function is a characteristic of a

structure, and it changes depending on material properties, ge-
ometry, support conditions and the existence of flaws or cracks.
The main components of impulse response test system are the
impact source that can be an instrumented hammer or a hammer
striking a load cell that is located on the surface of the test object,
a geophone (low frequency velocity transducer) and a two channel
dynamic signal analyzer or portable computer with data acquisi-
tion and signal analyzing capabilities.
The method is used mainly for testing of piles. Testing of

piles by this method is covered in ASTM test method D 5882 and
is known as transient response method.
CHAPTER-5
NON-DESTRUCTIVE TESTING OF STEEL BRIDGES
5.1 Introduction
Flaws and cracks can play havoc with the performance of

structures and for improving the performance, the timely detection
of these defects is very much necessary. Our present system of
inspection of bridges mainly emphasize on the visual inspection
which does not give correct picture of internal structural defects.
By using non-destructive testing methods, the structures can be
evaluated to a greater degree of accuracy, without damaging them.
These methods can be used as quality control measures at the
time of construction of structures as well as tool for detection of
defect during the service. The biggest advantage of NDT methods
is that these are quick and large no. of structure can be covered to
evaluate their in service performance without causing any damage
to the structure. In this chapter, only the following methods which
are commonly used for evaluating the steel structures, are
discussed –
(a) Liquid Penetrant Inspection

(b) Magnetic Particle Inspection
(c) Eddy current testing
(d) Radiography testing
(e) Ultrasonic testing
5.2 Liquid Penetrant Inspection (LPI)
This method is used to detect surface flaws by bleed out

of a coloured or fluorescent dye from the flaw. The technique is
based on the ability of a liquid to be drawn into a clean surface
breaking flaw by capillary action. After a period of time called the
“dwell”, excess surface penentrant is removed and a developer
applied. This acts as a blotter and draws the penetrant from the
flaw, which indicates the presence and location of the flaw.
(71)
The method can detect the cracks/flaws which are open

to the surface but internal cracks/blow holes etc. cannot be
detected using this method. Sometimes the very narrow flaws/
cracks cannot be detected by visual inspection because of the
less size. But using liquid penetrant inspection, even these narrow
cracks can be detected. LPI produces a flaw indication that is
much larger and easier for the eye to detect. Secondly, the LPI
produces a flaw indication with a high level of contrast between
the indication and background which makes the detection easier.
5.2.1 Methodology
Following methodology is adopted for carrying out this test.
(a) Surface preparation – This is one of the most important

and critical steps of a liquid penetrant inspection. The
surface must be free of oil, grease, water or other
contaminants that may prevent penetrant from entering
the flaw.
(b) Penetrant application: Once the surface has been

thoroughly cleaned and dried ,the penetrant material is
applied by spraying, brushing, or immersing the parts in a
penetrant bath.
(c) Penetrant dwell – The penetrant is left on the surface for a

sufficient time to allow as much penetrant as possible to
be drawn from or to seep into a crack/flaw. Pentetrant
dwell time is the total time that the penetrant is in contact
with the surface. The dwell time is normally recommended
by the manufacturer of the dye and is the part of material
specifications.
(d) Excess penetrant removal – The excess penetrant must

be removed from the surface of the sample, while remove
as little penetrant as possible from the crack flaw.
Depending upon the penetrant system used, this may
involve cleaning with a solvent, direct rinsing with water,
or first treated with an emulsifier and then rinsing with
(72)
water.
(e) Developer Application: A thin layer of developer is sprayed
to draw penetrant trapped in flaws back to the surface,
where it is visible. Developers normally comes in powder
or liquid (Spray) form. The developer is allowed to stand
on part surface for a period of time sufficient to permit the
extraction of the trapped penetrant out of any surface flaws.
5.2.2 Material Properties
The penetrant must have following properties:
(a) Spread easily over the surface of the material being

inspected to provide complete coverage.
(b) Be drawn into surface defects by capillary action
(c) Remain in the defect but remove easily from the surface
(d) Remain fluid so that it can be drawn back to the surface

through the developer application
(e) Should not be harmful to the material/personnel carrying

out the tests.
Penetrant materials are of two basic types. These types are

indicated below –
(a) Type-1 – Fluorescent penetrants
(b) Type-2 – Visible penetrants
Depending upon the application the penetrant type to be

used will vary in the field. For bridge inspection/testing normally
type 2 penetrant is used, because these can be used easily in the
field and does not require any darkened area.
The role of the developer is to pull the trapped penetrant

material out of defects and to spread the developer out on the
surface of the part, so that it can be seen by an inspecting official.
(73)
Normally water-soluble or water suspendible developers are used

for testing purpose. These developers are applied over the surface
by spraying.
5.2.3 Advantages and Disadvantages
Like any other NDT method, LPI also has its own
advantages and disadvantages. Some of the advantages of LPI
method are listed below:
(a) The method has the high sensitivity to small surface

discontinuities.
(b) Large areas and large volumes can be inspected rapidly and
at low cost.
(c) Parts with complex geometric shapes are routinely inspected.
(a) Indications are produced directly on the surface of the part.
(e) Relatively inexpensive and easy to perform.
Some of the disadvantages of this method are listed below:
(a) Only surface breaking defects can be detected.
(b) Only materials with a relative non-porous surface can be

inspected.
(c) Proper cleaning is a prerequisite as contaminants can mask

defects.
(d) The surface finish and roughness can affect inspection

sensitivity.
5.3 Magnetic Particle Inspection (MPI)
Magnetic particle inspection is a NDT method used for

defect detection in steel structures. This is a fast and relatively
easy method to apply in field. MPI uses magnetic fields and small
(74)
magnetic particles, such as iron fillings to detect flaws in

components. The component being inspected must be made of a
ferromagnetic particle such as iron, nickle, cobalt or some of their
alloys. Ferromagnetic materials are materials that can be magnetic
to a level that will allow the inspection to be effective.
The method may be used effectively for inspection of steel

girders and other bridge parts made of steel.
5.3.1 Principle
When ferromagnetic material or component (weld) is

magnetized, magnetic discontinuities that lie in direction approx.
perpendicular to the field direction, will result in formation of a
strong leakage field. This leakage field is present at and above
the surface of magnetized component and its presence can be
visibly detected by the cluster of finely divided magnetic particle
i.e. when crack is met to magnetic field direction it will form local
magnet and will attract fine particles along the crack when sprayed.
Magnetization may be induced in the component by using
permanent magnet or electromagnet. For simple illustration,
consider a bar magnet. It has a magnetic field in and around the
magnet. Any place, that a magnetic line of force exits or enters
the magnet, it called a pole. A pole where magnetic line of force
exits is called a north pole and where a line of force enters the
magnet is called a south pole (Fig 5.3.1)
Fig 5.3.1 Magnetic Line of Force

(75)
When a bar magnet is broken in the center of its length,

two complete bar magnets with magnetic poles at each end of
each piece will form. If the magnet is just cracked but not broken
completely in two, a north and south pole will form at each edge of
the crack. The magnetic field exits the north pole and reenters at
the south pole. The magnetic field spreads out when it encounters
the small air gap created by the crack, because the air cannot
support as much magnetic field per unit volume as a magnet can.
When the field spreads out, it appears to leak out of the material
and, thus it is called a flux leakage field (Fig 5.3.2.)
Fig. 5.3.2 Magnetic flux leakage field
If iron particles are sprinkled on a cracked magnet, the

particles will be attracted to and cluster will be formed not only at
the ends of the magnet (poles) but also at poles formed at the
edges of the cracks. This formation cluster of particles along the
edges of the cracks can be easily detected.
The direction of magnetic field in an electro magnetic circuit

is controlled by the direction of current flow. The effectiveness of
the defect indication will depend on the orientation of the flaw to
the induced magnetic field and greatest when defect is
perpendicular. Hence to detect a defect in a member/weld, it has
to be tested in both axis i.e. xx-axis as well as yy-axis.
(76)
5.3.2 Equipments and Methodology
For proper inspection of a component, it is important to

establish a magnetic field in at least two directions, so that defects
lies in the different directions can be detected. For establishing
magnetic field in component various types of equipments are
available which are discussed below –
(a) Permanent magnets – The primary types of permanent

magnets are bar magnets and horseshoes (yoke)
magnets. These are very strong magnets and difficult to
handle in the field because large force is required to remove
them from the component being inspected. Normally these
are used for underwater inspection and for the explosive
environment, where electromagnets cannot be used.
(b) Electromagnets – These type of magnets are most widely

used in the MPI equipments. In this equipment, electrical
current is used to produce the magnetic field. An
electromagnetic yoke is a very common piece of equipment
which is made by wrapping an electrical coil around a
piece of soft ferromagnetic steel. A switch is included in
the electrical circuit so that current as well as magnetic
field can be turn on and off. This type of magnet generates
a very strong magnetic field in a local area where the poles
of magnet touch the part to be inspected.
(c) Prods – These are hand held electrodes that are pressed
against the surface of the component being inspected to
make contact for passing electrical current through steel.
The current passing between the prods creates a circular
magnetic field around the prods that can be used for
magnetic particle inspection. Prods are made from copper
and have an insulated handle. One of the prods have a
trigger switch so that the current can be quickly and easily
turned on and off. Sometimes the two prods are connected
by any insulator to facilitate one hand operation. This is
known as dual prod also and generally used for weld
inspection.
(77)
(d) Portable coils and conductive cables – These are used to

establish a longitudinal magnetic field within a component,
when a preformed coil is used, the component is placed
against the inside surface on the coil.
All the above said equipments are portable

equipments and can be used in the field without any
handling problems.
Following methodology to be followed while

performing the test in the field –
(1) The surface should be cleaned before inspection.

The surface must be free of grease, oil or other
moisture.
(2) Apply the magnetizing force using permanent

magnets, a electromagnetic yoke, prods, a coil
or other means to establish the necessary
magnetic flux.
(3) Dust on the light layer of magnetic particles with

the magnetizing force still applied, remove the
excess powder from the surface with few gentle
puf of dry air.
If wet suspension is used, then the

suspension is gently sprayed or flowed over the
surface to be tested. Immediately after the
application of wet suspension the magnetizing
force should be applied.
(4) After this the area should be inspected carefully

for finding out the cluster of particles. Surface
discontinuities will produce a sharp indication.
(78)
5.4 Eddy Current Testing
This is one of the several NDT methods that use the

principal of electromagnetism as the basis for conducting the test.
Eddy currents are created through a process called electromagnetic
induction. When alternating current is applied to the conductor,
such as copper wire, a magnetic field develops in and around the
conductor. This magnetic field expands as the alternating current
rises to maximum and collapses as the current is reduced to zero.
If another electrical conductor is brought into the close proximity
to this changing magnetic field, current will be induced in this
second conductor. Eddy current are induced electrical currents
that flow in a circular path. They get their names from “eddies”
that are formed when a liquid or gas flows in a circular path around
obstacles.
The most basic eddy current testing instrument consists

of an alternating current source, a coil of wire connected to this
source, and a voltmoter to measure the voltage change across the
coil. An ammeter could also be used to measure the current
change in the circuit instead of using the voltmeter.
For generating eddy current, a “probe” is used which

consists of electrical conductor formed into a coil and housed
inside the probe. These probes are available in a large variety
shapes and sizes. In fact, one of the major advantages of eddy
current inspection is that probes can be custom designed for a
wide variety of applications. Eddy current probes are classified by
the configurations and mode of operation of the test coils. The
configuration of probes generally refers to the way the coil or coils
are placed with reference to test area. An example of different
configuration of probes would be bobbin probes, which are inserted
into a piece of pipe to inspect from inside out. While in encircling
probes, the coil or coils encircle the pipe to inspect from outside
in. The mode of operation refers to the way the coil or coils are
wired and interface with the test equipment. The mode of operation
of a probe generally falls into one of four categories, absolute,
differential, reflection and hybrid. Normally differential probes are
used for flaw detection in steel members.
(79)
5.4.1 Methodology
Eddy current equipment can be used for a variety of

applications such as detection of cracks (discontinuity),
measurement of metal thickness, detection of metal thining due
to corrosion and erosion, determination of coating thickness and
the measurement of electrical conductivity and magnetic
permeability.
For inspection of bridge girder, this technique can be used

for detection of surface breaking cracks. This is an excellent method
for detecting surface and near surface defects when the probable
defect location and orientation is well known. Defects such as
cracks are detected when they disrupt the path of eddy current
and weaken their strength. The Fig. 5.4.1 shows an eddy current
surface probe on the surface of a conductive component.
Fig. 5.4.1 Eddy current surface probe indicating no defect
The strength of the eddy current under the coil of the probe
is indicated by colour. In Fig .5.4.2, there is a flaw under the right
side of the coil and it can be seen that the eddy current are weaker
in that area.
(80)
Fig. 5.4.2 Eddy current surface probe indicating

defect on right hand side
While performing the inspection with surface probe, fol-

lowing methodology should be adopted,
(a) Select and setup the instrument and probe.
(b) Select a frequency to produce the desired depth of

penetration.
(c) Adjust the instrument to obtain an easily recognizable

defect response using a calibration standard or set up
specimen.
(d) Place the inspection probe (coil) on the component sur-

face.
(e) Scan the probe over part of the surface in a pattern that
will provide complete coverage of the area being inspected.
Care must be taken to maintain the same probe to sur-
face orientation as probe wobble can affect interpretation
of the signal.
(f) Monitor the signal for a local change in impedance that

will occur as the probe moves over a discontinuity.
(81)
This method is very sensitive to small cracks and other

defects. This method detects surface and near surface defects
very efficiently. The results can be obtained immediately after
inspection. The equipment required for test is very small and por-
table and minimum part preparation is required for carrying out
this test. During the test, the test probe does not need to contact
the part.
One of the major limitation is that the depth for penetra-

tion is limited so it cannot detect the internal defects which are
located away from the surface. The surface to be tested must be
accessible to the probe. Flaws such as delamination that lie par-
allel to the probe coil winding and probe scan direction cannot be
detected easily.
5.5 Radiographic Testing
This is the technique of obtaining a shadow image of a

solid using penetrating radiation such as X-rays or gamma rays.
These rays are used to produce a shadow image of an object on
film. Thus if X-ray or gamma ray source is placed on one side of a
specimen and a photographic film on the other side, an image is
obtained on the film which is in projection, with no details of depth
within the solid. Images recorded on the films are also known as
radiographs.
The contrast in a radiograph is due to different degrees of

absorption of X-rays in the specimen and depends on variations in
specimen thickness, different chemical constituents, non-uniform
densities, flaws, discontinuities, or to scattering processes within
the specimen.
Some of the other closely related methods are Tomogra-

phy, Radioscopy, Xerography etc.
5.5.1 Methodology
First step of the method is to examine carefully the

(82)
specimen and to decide on the direction to examine the object

considering the probable orientation of defects and the thickness
of the specimen in relation to the diverging beam of X-rays.
Considering the thickness of object, density of the material

etc., the wavelength of X-ray to be used should be decided.
The images can be observed on an image intensifying

tube with remote viewing or recorded on film with or without
intensifying screens. Grid or blocking materials should be used
to reduce scattering effects. The optimum time of exposure need
to be determined by experimental trials.
The last but the most important step is the interpretation

of radiograph. Radiographs are projections, providing no information
about depth within the specimen. While interpreting following factors
normally should be considered –
(a) Orientation of the object to permit any discontinuity or

defect to show maximum contrast.
(b) Use of radiation so that to have largest possible differ-
ences in the relative absorption coefficients of the differ-
ent compositions present.
(c) The selection of wavelength of X-ray to control sharpness
and contrast of the image.
(d) Use of well illuminated viewing screen under optimum light-
ing conditions.
(e) Probable defects in the specimen.
(f) The X-ray target to film distance should not be less than
10 x the thickness of specimen.
(g) The greatest dimension of the suspected flaw should be
parallel to X-ray beam.
For conducting this test access to opposite side of the

object is required. X-rays and gamma-rays are dangerous and lot
of safety precautions to be taken while conducting the test. A
discontinuity of thickness less than 2% of the overall thickness of
the specimen is difficult to observe. This method is relatively
(83)
expansive method. Normally this method is used for detecting

internal flaws in the welds especially butt welds.
5.6 Ultrasonic Inspection
In this method ultrasonic waves of high frequency above

the audible range, that is, above 20 KHz are used for detection of
flaws in the test object. The following are normally required to
carry out this test –
(a) Transducers
(b) Pulse echo display systems
(c) Amplifier
(d) Electrical pulse generator
The wavelengths, frequencies and wave velocities used in

non-destructive testing are generally –
(a) Wavelength: 1 to 10mm

(b) Frequencies: 0.1 to over 15 MHz
(c) Sound velocities: 1 to 10 Km/s
5.6.1 Principle
Ultrasonic waves are transmitted through solids over dis-

tance of several meters in fine-grain steels, but only about 10cm
in some cast irons. Discontinuities or defects cause scattering
and reflection of the waves, and the detection of reflected or trans-
mitted waves permits the defect to be located. Various method
used for defect detection are described in Fig. 5.6.1
The most popular method for flaw/defect detection is pulse

echo method (Fig 5.6.1.(a)) in which the same transducer trans-
mits and receives the ultrasonic pulse. (only one transducer is
required). In other methods two transducers are required out of
which one act as transmitter and other as receiver transducer.
(84)
Fig. 5.6.1 Various Ultrasonic Inspection Methods
In transmission method, access to both sides of the specimen

is required (Fig 5.6.1(b)) while in back reflection method, the
detection of flaws can be done even when the access is restricted
to only one side of specimen (Fig. 5.6.1(c) & (d)). The transmission
method is used for detection of small size defects because small
size defects cannot be detected by pulse echo method. For thin
objects also, the pulse echo method cannot be used effectively
because of the dead zone effect.
For pulse echo method, an oscilloscope is required to

detect the time as well as well as amplitude of reflected pulse.
The schematic diagram describing the pulse echo method is shown
in Fig. 5.6.2.
(85)
Fig 5.6.2. Pulse Echo Method
The transducer touches the surface of specimen through

a couplant, sending a pulse of ultrasonic waves traveling through
the medium. The ultrasonic pulse is reflected from the rear sur-
face, if no flaw is present, and detected by the same transducer if
normal 0° probes are used. This pulse reflected from the rear
surface will be displayed on oscilloscope as back echo. If a flaw is
present inside the test object, a flaw signal will be produced (be-
cause of reflection of waves from flaw) earlier than that from the
rear surface. This flaw signal will be displayed on the oscillo-
scope as flaw echo between surface echo and back echo. The
distance of flaw echo on x-axis of oscilloscope will indicate the
location of the flaw inside the test object. While the amplitude of
flaw echo on y-axis of oscilloscope will indicate the magnitude or
size of the flaw. Depending upon the inclination of flaw inside the
test object different types of probes are used for detection of flaws.
(86)
The probe can be 0° normal probe or angle probe. In normal probes

the detection of flaw is done using longitudinal waves. While in
angles probes, the transverse or shear waves are used for detec-
tion of flaws. In case of angle probes, no surface or back echo will
appear on the screen. However flaw echo will appear on the screen
if the orientation of the flaw is perpendicular to direction of travel of
ultrasonic waves inside the test object. As the angle probe will
move towards the flaw, the flaw echo appearing on the oscillo-
scope will more from right to left. Similarly, when the probe will
move away from the flaw, the flaw echo will move from left to right
on the oscilloscope.
5.6.2 Calibration and reference standards
The reflection from a flaw is displayed on the oscilloscope

in the form of flaw echo cannot be interpreted directly in terms of
size or amplitude of flaw. The normal practise is to compare the
signal position and amplitude with the signals from a calibrated
reference test pieces. Some of the reference test pieces / refer-
ence blocks are
(i) Test block IIW-A2 (International Institute of Weld-
ing (Fig. 5.6.3)
Fig 5.6.3 IIW-A2 Block
(ii) American Welding Society (AWS) blocks

(Fig. 5.6.4).
(87)
Fig. 5.6.4 AWS Block
For thickness calibration, using normal probes, six steps steel

calibration block is used (Fig. 5.6.5).
Fig 5.6.5 Six steps steel calibration block
5.6.3. Application of Ultrasonic Testing Method
This method is not suitable for testing of coarse grained

structures. Most of the castings cannot be scanned using this
method because of the coarse grained structure which leads to
(88)
scattering and attenuation of waves. This method is suitable for

scanning of fine grained structure. Rolled sheets and plates are
suitable for ultrasonic testing. Normal probes are used for detect-
ing laminations and angle probes for fast inspection of plates for
most of the discontinuities except smooth laminations parallel to
the surface.
Before starting the test, the equipment should be tested

with a calibration block. The surface to be tested should be smooth
and plain. The couplant must be used for testing purpose. The
thickness of couplant layer must be as less as possible. A thick
layer will affect the direction of the ultrasonic beam in the test
piece. For detection of smaller flaws, small diameter high fre-
quency transducers are used.
CHAPTER-6
NON-DESTRUCTIVE TESTING OF MASONRY BRIDGES
6.1 Introduction
As already explained in chapter 1, the use of NDT methods

for testing of masonry structures is not very common in India.
However there is a necessity of adopting suitable NDT methods
for evaluation of masonry structures as existing system of
inspection is not sufficient to cover all the aspects of inspection.
Sometimes very critical defects like, deterioration of masonry
materials, internal cavities formed due to rat holes etc and cracking
of structures due to overstressing go unnoticed which may proved
to be very fatal for the safety of structure. The NDT methods have
a large potential to be part of system for inspection and monitoring
of structures. This includes quality assurance during and after
construction, identification of damages in an early stage and to
decide the repair strategy for rehabilitation of the structures. Some
of the NDT methods which are used for evaluation and inspection
of masonry structures are listed below –
(a) Flat Jack Testing

(b) Impact Echo Testing
(c) Impulse radar testing
(d) Infrared thermography
6.2 Flat Jack Testing
This test can determine the engineering properties of older

structures for structural evaluation. This method is used to
determine the in situ stress and compressive strength of masonry
structures.
A flat jack is a flexible steel envelope, thin enough to fit

within a masonry mortar joint. During testing, the flat jack is
hydraulically pressurized and applies stress to the surrounding
(90)
masonry.
This method directly measures the actual state of

compressive stress present within the masonry and is useful for
determining stress gradients present within a masonry wall or
column. The in situ stress test works on basic principle of stress
relief, when mortar is removed from a joint, compressive stress
within the masonry forces the slot thus formed to close by a small
amount. A flat jack is inserted into the slot and pressurized to
restore the slot to its original opening dimension. The pressure at
which the original opening is restored is adjusted by the flat jack
calibration constant, providing a measure of the in situ masonry
compressive stress.
The other test is, in situ deformability test which is used

for direct measurement of masonry deformability properties and to
estimate the masonry compressive strength. For conducting this
test, two parallel flat jacks are used which subject the masonry
between them to compressive stress. The stress strain curve
which is obtained during the test, is used for obtaining both
compressive modulus and an estimate of compressive strength.
6.3 Impact Echo Testing
This is a sophisticated version of “sounding” a material

which enables the user to make judgment about internal conditions.
The technique involves a hammer or steel balls striking a

masonry surface, with a receiving transducer located near the
impact point. The hammer and receiver are connected to a
computer that records the input energy from the hammer and the
reflected compression wave energy from the receiver. The out put
is processed by computer using software to produce a frequency
domain display where reflections (or echoes) are seen as peaks
in the wave signals. In particular, thickness made of vibrations are
primarily used to identify the back wall or planar flaws. For that,
the time domain signal of displacement or velocity is usually
detected a few centimeters beside the impact point. Performing
an Fast Fourier Transform (FFT) operations then leads to significant
peaks in the amplitude spectrum which can be associated with
(91)
the depth of back wall or flaws if the effective velocity of propagation

of longitudinal waves in the structure is known.
With regard to overall soundness of the masonry, generally

speaking, the denser the material, the higher the wave velocity
response. This is a qualitative measurement that is useful in
surveys for comparative purposes. The thickness of a material
can be determined if the characteristic wave velocity is known.
An important limitation of the interpretation of Impact Echo

data is concerned with the effect of lateral boundaries of the
structure under investigation. These geometrical effects caused
by reflections of wave fronts at the outer boundaries of the specimen
produce systematic error in thickness and flaw depth
determination. These uncertainities must be taken into account if
the measurements are performed at specimens with lateral
boundaries lying in the vicinity of the measuring point.
6.4 Impulse Radar Testing
For the radar investigations, the electromagnetic waves

between 500 MHz and 1.5 GHz are pulsed into a material by
means of a transducer and read by an antenna receiver. The short
electromagnetic waves are transmitted into the material using a
dipole antenna and the impulses are reflected at the interface
between materials with different dielectric properties, i.e. at the
surface and backside of walls, at detachments, voids, metallic
inclusions etc. When the transmitting and receiving antennas,
which are normally contained in the same housing are moved
laterally over the surface of the object under investigation,
radargrams (colour or gray scale intensity charts over the position
of the antenna and impulse travel time) are generated. Using these
radargrams, the change in materials, voids or buried objects can
be detected.
The method is a very useful tool to get information about

the internal section of a masonry structure. The location of the
metallic inclusion can be detected with great accuracy. The inner
structure of masonry walls can be investigated with adequate
(92)
resolution related to the thickness and the presence of voids etc.

This method gives better results if the masonry structure is in dry
condition. The higher moisture content in the structure, results
into high absorption of electromagnetic waves due to which the
information content of the reflected waves reduces drastically.
6.5 Infrared Thermography
This method is also known as heat imagery. The technique

involved is that an object having a temperature above absolute
zero will radiate electromagnetic waves. Wavelength fall within
certain bands, depending on temperature. Wavelengths at room
temperature are outside the visible spectrum, while those at very
high temperature are shorter and fall within the visible spectrum.
Cameras or video equipments are used to photograph the surface
temperature of the object. The resulting video image indicate
surface temperature variations. In masonry construction, different
wavelengths often indicate the presence of moisture. The results
indicate whether the masonry is dense/sound or porous/
deteriorated.
(93)
LIST OF FIRMS DEALING WITH NDT EQUIPMENTS :
1. M/s AIMIL LTD., A-8, MOHAN COOPERATIVIE INDUSTRIAL

ESTATE, MATHURA ROAD, NEW DELHI.
2. M/s HILTI INDIA PVT. LTD.,8 LSC PUSHPA VIHAR COMMUNITY

CENTRE, NEW DELHI
3. M/s ULTRA TECHNOLOGIES PVT. LTD, B-85, KALKAJI,

NEW DELHI.
4. M/s. ENCARDIO RITES, LUCKNOW
5. M/s. JAMES INSTRUMENTS LUC. 3727, NORTH AEDZIE AVENUE,

CHICAGO ILLINOIS 60618, U.S.A.
6. PROSEQ U.S.A., RIESHASH STRASSE 57 CH - 8034 ZURICH,

SWITZERLAND.
7. ELE INTERNATIONAL LTD., EAST MAN WAY, HEMEL

HAMPSTEAD HERTFORDSHIRE, HP2 7HB, ENGLAND.
(94)
REFERENCES:
1. IS-1311 (Part-1) : 1992 Non-Destructive Testing of Concrete -

methods of test, Part-I, Ultrasonic Pulse Velocity.
2. IS 13322 (Part-2) : 1992, Non-Destructive Testing of Concrete –

methods of test, Part 2, Rebound hammer.
3. RDSO Report No.BS-51 : Guidelines on use of Acoustic emission

technique
4. RDSO Report No.BS-52: Guidelines on use of corrosion monitoring

equipments
5. RDSO Report No.BS-53: Guidelines on use of ultrasonic

instruments for monitoring of concrete structures.
6. RDSO Report No.BS-50: Guidelines on use of Profometer.
7. RDSO Report No.BS-42: Guidelines on use of Microcovermeter
8. “Handbook on Non Destructive Testing of Concrete” (second edition)

by V.M. Malhotra and N.J. Carino
9. “Non destructive testing” by Louis Cartz.
10. RDSO Guidelines for inspection, maintenance and rehabilitation

of concrete bridges.

NDT Bridges

Uploaded by

Copyright:

Available Formats

NDT Bridges

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

NDT Bridges

Uploaded by

Copyright:

Available Formats

NON DESTRUCTIVE TESTING

INDIAN RAILWAY INSTITUTE OF CIVIL ENGINEERING

Non-destructive testing of bridges has assumed a

Indian Railway Bridge Manual (IRBM) prescribes

I hope this book will be found very much useful by

The subject “non-destructive testing of bridges” is

The IRICEN publication is an attempt to compile all

It would not be out of place to acknowledge the

Above all, the author is grateful to Sri Shiv Kumar,

CHAPTER-1 NON - DESTRUCTIVE TESTING OF BRIDGES -

1.2 Concrete Bridges 1

1.3 Steel Bridges 4

1.4 Masonry Bridges 5

CHAPTER-2 NON – DESTRUCTIVE TESTS FOR STRENGTH

2.1 Rebound hammer test (Schmidt Hammer) 6

2.2 Ultrasonic Pulse Velocity Tester 11

2.3 Combined use of Rebound hammer and Ultrasonic 23

2.5 Pull out Test 27

2.6 The Break-off Test 30

2.7 Penetration Resistance Methods 36

CHAPTER-3 NON – DESTRUCTIVE TESTS FOR CORROSION

3.2 Half-cell Potential Measurement Method 39

3.3 Resistivity Test 44

3.4 Tests for carbonation of Concrete 47

3.5 Test for chloride content of concrete 48

3.7 Micro Covermeter 51

CHAPTER-4 NON – DESTRUCTIVE TESTS FOR DETECTION

4.2 Infrared thermographic techniques 54

4.3 Acoustic Emission Technique 58

4.4 Short Pulse Radar Method 62

4.5 Stress Wave Propagation Methods 65

4.5.1 Pulse Echo method 66

CHAPTER-5 NON – DESTRUCTIVE TESTING OF STEEL

5.2 Liquid Penetrant Inspection 70

5.3 Magnetic Particle Inspection 73

5.5 Radiographic Testing 81

5.6 Ultrasonic Inspection 83

CHAPTER-6 NON – DESTRUCTIVE TESTING OF MASONRY

6.2 Flat Jack Testing 89

6.3 Impact Echo Testing 90

6.4 Impulse Radar Testing 91

6.5 Infrared Thermography 92

LIST OF FIRMS DEALING WITH NDT EQUIPMENTS 93

NON-DESTRUCTIVE TESTING OF BRIDGES - GENERAL

We may group the various bridges mainly in three types,

(i) Concrete bridges

Various types of bridges are having their own strengths,

1.2 Concrete Bridges

the control exercised during construction also contributes a lot to

Considering the above requirements, need of testing of

The NDT being fast, easy to use at site and relatively

(i) Testing any number of points and locations

Many of NDT methods used for concrete testing have their

Moreover the test measure some other property of concrete (e.g.

Variety of NDT methods have been developed and are

A. For strength estimation of concrete

(i) Rebound hammer test

B. For assessment of corrosion condition of

(i) Half cell potentiometer

C. For detection of cracks/voids/ delamination etc.