FILE NO.

050-200501

SERVICE MANUAL

COLOR TELEVISION

20AS25

DOCUMENT CREATED IN JAPAN, Jan., 2005

 SERVICING NOTICES ON CHECKING
1. KEEP THE NOTICES 6. AVOID AN X-RAY
As for the places which need special attentions, Safety is secured against an X-ray by consider-
they are indicated with the labels or seals on the ing about the cathode-ray tube and the high
cabinet, chassis and parts. Make sure to keep the voltage peripheral circuit, etc.
indications and notices in the operation manual. Therefore, when repairing the high voltage pe-
ripheral circuit, use the designated parts and
2. AVOID AN ELECTRIC SHOCK make sure not modify the circuit.
There is a high voltage part inside. Avoid an Repairing except indicates causes rising of high
electric shock while the electric current is voltage, and it emits an X-ray from the cathode-
flowing. ray tube.
3. USE THE DESIGNATED PARTS 7. PERFORM A SAFETY CHECK AFTER
The parts in this equipment have the specific SERVICING
characters of incombustibility and withstand
Confirm that the screws, parts and wiring which
voltage for safety. Therefore, the part which is
were removed in order to service are put in the
replaced should be used the part which has
original positions, or whether there are the
the same character.
portions which are deteriorated around the
Especially as to the important parts for safety
serviced places serviced or not. Check the
which is indicated in the circuit diagram or the
insulation between the antenna terminal or
table of parts as a mark, the designated
external metal and the AC cord plug blades.
parts must be used.
And be sure the safety of that.
4. PUT PARTS AND WIRES IN THE (INSULATION CHECK PROCEDURE)
ORIGINAL POSITION AFTER
1. Unplug the plug from the AC outlet.
ASSEMBLING OR WIRING 2. Remove the antenna terminal on TV and turn
There are parts which use the insulation on the TV.
material such as a tube or tape for safety, or 3. Insulation resistance between the cord plug
which are assembled in the condition that terminals and the eternal exposure metal
these do not contact with the printed board. [Note 2] should be more than 1M ohm by
The inside wiring is designed not to get closer using the 500V insulation resistance meter
to the pyrogenic parts and high voltage parts. [Note 1].
Therefore, put these parts in the original 4. If the insulation resistance is less than 1M
positions. ohm, the inspection repair should be
required.
5. TAKE CARE TO DEAL WITH THE
[Note 1]
CATHODE-RAY TUBE
If you have not the 500V insulation
In the condition that an explosion-proof cathode-
resistance meter, use a Tester.
ray tube is set in this equipment, safety is
secured against implosion. However, when [Note 2]
removing it or serving from backward, it is External exposure metal: Antenna terminal
dangerous to give a shock. Take enough care to Earphone jack
deal with it.

HOW TO ORDER PARTS

Please include the following informations when you order parts. (Particularly the VERSION LETTER.)
1. MODEL NUMBER and VERSION LETTER
The MODEL NUMBER can be found on the back of each product and the VERSION LETTER can be
found at the end of the SERIAL NUMBER.
2. PART NO. and DESCRIPTION
You can find it in your SERVICE MANUAL.

IMPORTANT
Inferior silicon grease can damage IC's and transistors.
When replacing an IC's or transistors, use only specified silicon grease (YG6260M).
Remove all old silicon before applying new silicon.

A1-1
ABOUT LEAD FREE SOLDER (PbF)
Distinction of PbF PCB:
PCBs (manufactured) using lead free solder will have a PbF printing on the PCB.
(Please refer to figures.)

Caution:
• Pb free solder has a higher melting point than standard solder;
Typically the melting point is 50°F~70°F(30°C~40°C) higher.
Please use a soldering iron with temperature control and adjust it to 650°F ± 20°F (350°C ± 10°C).
In case of using high temperature soldering iron, please be carefull not to heat too long.
• Pb free solder will tend to splash when heated too high (about 1100°F/ 600°C).
• All products with the printed circuit board with PbF printing must be serviced with lead free solder.
When soldering or unsoldering, completely remove all of the solder from the pins or solder area,
and be sure to heat the soldering points with the lead free solder until it melts sufficiently.

Recommendations
Recommended lead free solder composition is Sn-3.0Ag-0.5Cu.

A1-2
 CONTENTS

SERVICING NOTICES ON CHECKING ...................................................................................................... A1-1

HOW TO ORDER PARTS ........................................................................................................................... A1-1
IMPORTANT ................................................................................................................................................ A1-1
ABOUT LEAD FREE SOLDER (PbF) ......................................................................................................... A1-2
CONTENTS ................................................................................................................................................. A2-1
GENERAL SPECIFICATIONS .................................................................................................................... A3-1~A3-5
DISASSEMBLY INSTRUCTIONS
1.REMOVAL OF ANODE CAP .............................................................................................................. B1-1
2.REMOVAL AND INSTALLATION OF FLAT PACKAGE IC ............................................................... B2-1, B2-2
SERVICE MODE LIST ................................................................................................................................. C-1
CONFIRMATION OF HOURS USED .......................................................................................................... C-1
WHEN REPLACING EEPROM (MEMORY) IC ........................................................................................... C-1
ELECTRICAL ADJUSTMENTS .................................................................................................................. D-1~D-4
BLOCK DIAGRAM ...................................................................................................................................... E-1, E-2
PRINTED CIRCUIT BOARDS
MAIN/CRT ............................................................................................................................................... F-1~F-4
SCHEMATIC DIAGRAMS
MICON/CHROMA/TUNER ...................................................................................................................... G-1, G-2
TV POWER ............................................................................................................................................. G-3, G-4
DEFLECTION/CRT ................................................................................................................................. G-5, G-6
SOUND/AV ............................................................................................................................................. G-7, G-8
WAVEFORMS ............................................................................................................................................. H-1, H-2
MECHANICAL EXPLODED VIEW .............................................................................................................. I-1, I-2
MECHANICAL REPLACEMENT PARTS LIST .......................................................................................... J1-1
ELECTRICAL REPLACEMENT PARTS LIST ............................................................................................ J2-1~ J2-3

A2-1
 GENERAL SPECIFICATIONS
G-1 TV CRT CRT Size / Visual Size 19 inch / 480.0mmV
System CRT Type Normal
Deflection 90 degree
Magnetic Field BV/BH +0.35G/0.30G
Color System NTSC
Speaker 1Speaker
Position Bottom
Size 3 Inch
Impedance 8 ohm
Sound Output MAX 1.5 W
10%(Typical) 1.0 W
NTSC3.58+4.43 /PAL60Hz No
G-2 Tuning Broadcasting System US System M
System Tuner and System 1Tuner
Receive CH Destination USA(W/ CATV)
Tuning System F-Synth
Input Impedance VHF/UHF 75 ohm
2 - 69, 4A, A-5 - A-1,
CH Coverage A - I, J - W, W+1 - W+84
Intermediate Picture(FP) 45.75MHz
Frequency Sound(FS) 41.25MHz
FP-FS 4.50MHz
Preset CH No
Stereo/Dual TV Sound No
Tuner Sound Muting Yes
G-3 Power Power Source AC 120V AC 60Hz
DC
Power Consumption at AC
73 W at AC 120 V 60 Hz
Stand by (at AC) 5 W at AC 120 V 60 Hz
Per Year -- kWh/Year
Protector Power Fuse Yes
G-4 Regulation Safety UL
Radiation FCC
X-Radiation DHHS
G-5 Temperature Operation +5oC ~ +40oC
Storage -20oC ~ +60oC
G-6 Operating Humidity Less than 80% RH

A3-1
 GENERAL SPECIFICATIONS
G-7 On Screen Menu Yes
Display Menu Type Character
Picture Yes
Contrast Yes
Brightness Yes
Color Yes
Tint Yes
Sharpness Yes
Audio No
Bass No
Treble No
Balance No
BBE On/Off No
Stable Sound On/Off No
CH Set Up Yes
TV/CABLE(CATV) Yes
Auto CH Memory Yes
Add/ Delete Yes
Language Yes
V-chip Yes
Lock Yes
On Timer Yes
CH Label No
Favorite CH No
Color Stream DVD/DTV No
Control Level Yes
Volume Yes
Brightness Yes
Contrast Yes
Color Yes
Tint Yes
Sharpness Yes
Tuning No
Bass No
Treble No
Balance No
Back Light No
Stereo,Audio Output,SAP No
Video Yes
Color Stream No
Channel(TV/Cable) Yes
CH Label No
Game Timer Yes
Sleep Timer Yes
Sound Mute Yes
V-chip Rating Yes
G-8 OSD Language English French Spanish

G-9 Clock and Sleep Timer Max Time 120 Min

Timer Step 10 Min
On Timer Program(On Timer ) Yes
Wake Up Timer No
Timer Back-up (at Power Off Mode) more than -- Min Sec

A3-2
 GENERAL SPECIFICATIONS
G-10 Remote Unit RC-EH
Control Glow in Dark Remocon Yes[From '04 DEC O/R]
Format Toshiba
Custom Code 40-BF h
Power Source Voltage(D.C) 3V
UM size x pcs UM-4 x 2 pcs
Total Keys 27 Keys
Keys Power Yes
1 Yes
2 Yes
3 Yes
4 Yes
5 Yes
6 Yes
7 Yes
8 Yes
9 Yes
0 Yes
100 No
CH Up Yes
CH Down Yes
Volume Up Yes
Volume Down Yes
TV/Caption/Text Yes
CH1/CH2 Yes
TV/Video(TV/AV) Yes
CH RTN/CH ENT(Quick View) Yes
Sleep Yes
RE Call(Call) Yes
Reset Yes
Menu Yes
Enter Yes
Mute Yes
Exit No
MTS(Audio Select) No
Set + Yes
Set - Yes
Multi Brand Keys CH Up(VCR) No
CH Down(VCR) No
Pause/Still No
TV/VCR(VCR) No
Code No
FF No
Rew No
Rec No
Play No
Stop No
TV No
VCR No
Cable No

A3-3
 GENERAL SPECIFICATIONS
G-11 Features Auto Degauss Yes
Auto Shut Off Yes
Canal+ No
CATV Yes
Anti-theft No
Rental No
Memory(Last CH) Yes
Memory(Last Volume) Yes
V-Chip Yes
Type USA,ORION Type
BBE No
Auto Search No
CH Allocation No
SAP No
Just Clock Function No
CH Label No
VM Circuit No
Full OSD No
Premiere No
Comb Filter No
Lines
Auto CH Memory Yes
Hotel Lock No
Closed Caption Yes
Stable Sound No
FBT Leak Test Protect Yes
CH Lock Yes
Video Lock Yes
Game Timer (Max Time:120 Min) Yes
Stable Sound No
Energy Star No
Power On Memory Yes
Favorite CH No
G-12 Accessories Owner's Manual Language English / Spanish
W/ Warranty No
Remote Control Unit Yes
Rod Antenna No
Poles
Terminal
Loop Antenna No
Terminal
U/V Mixer No
DC Car Cord (Center+) No
Guarantee Card Yes
Warning Sheet No
Circuit Diagram No
Antenna Change Plug No
Service Facility List No
Important Safety Instruction No
Dew/AHC Caution Sheet No
AC Plug Adapter No
Quick Set-up Sheet No
Battery Yes
UM size x pcs UM4 x 2
OEM Brand No
AC Cord No
AV Cord (2Pin-1Pin) No
Registration Card (NDL Card) No
ESP Card No
PTB Sheet No
300 ohm to 75 ohm Antenna Adapter No

A3-4
 GENERAL SPECIFICATIONS
G-13 Interface Switch Front Power Yes
System Select No
Main Power SW No
Sub Power No
Channel Up/Reset Yes
Channel Down/Enter Yes
Volume Up/Set Up Yes
Volume Down/Set Down Yes
MENU=Volume Up+Volume Down Yes
Rear AC/DC No
TV/CATV Selector No
Degauss No
Main Power SW No
Indicator Power Yes
Stand-by No
On Timer No
Terminals Front Video Input RCA
Audio Input RCA x 1
Other Terminal No
Rear Video Input(Rear1) No
Video Input(Rear2) No
Audio Input(Rear1) No
Audio Input(Rear2) No
Video Output No
Audio Output No
Euro Scart No
Color Stream No
Diversity No
Ext Speaker No
DC Jack 12V(Center +) No
VHF/UHF Antenna Input F Type
AC Outlet No
G-14 Set Size Approx. W x D x H (mm) 488 x 465 x 416
G-15 Weight Net (Approx.) 17.5kg ( 38.6 lbs)
Gross (Approx.) 20.0kg ( 44.1lbs)
G-16 Carton Master Carton No
Content ---- Sets
Material -- /--
Dimensions W x D x H(mm) -- x -- x --
Description of Origin No
Gift Box Yes
Material Double/Brown
Dimensions W x D x H(mm) 546 x 526 x 472
Design As per Buyer's
Description of Origin Yes
Natural Dropping At 1 Corner / 2 Edges / 4
Drop Test
Surfaces
Height (cm) 60 (ORION SPEC:46)
Container Stuffing 436 Sets/40' container
G-17 Cabinet Material Cabinet Cabinet Front PS 94V0 DECABROM
Cabinet Rear PS 94V0 DECABROM
PCB Non-Halogen Demand No
Eyelet Demand Yes
G-18 Environment Pb Free Phase3

A3-5
 DISASSEMBLY INSTRUCTIONS
1. REMOVAL OF ANODE CAP 3. After one side is removed, pull in the opposite direction to
remove the other.
Read the following NOTED items before starting work.
NOTE
* After turning the power off there might still be a potential
voltage that is very dangerous. When removing the Take care not to damage the Rubber Cap.
Anode Cap, make sure to discharge the Anode Cap's INSTALLATION
potential voltage.
1. Clean the spot where the cap was located with a small
* Do not use pliers to loosen or tighten the Anode Cap
amount of alcohol. (Refer to Fig. 1-3.)
terminal, this may cause the spring to be damaged.
REMOVAL
1. Follow the steps as follows to discharge the Anode Cap. Location of Anode Cap
(Refer to Fig. 1-1.)
Connect one end of an Alligator Clip to the metal part of a
flat-blade screwdriver and the other end to ground.
While holding the plastic part of the insulated Screwdriver,
touch the support of the Anode with the tip of the
Screwdriver.
A cracking noise will be heard as the voltage is discharged.

Fig. 1-3

GND on the CRT NOTE

Confirm that there is no dirt, dust, etc. at the spot where
the cap was located.
2. Arrange the wire of the Anode Cap and make sure the
wire is not twisted.
3. Turn over the Rubber Cap. (Refer to Fig. 1-4.)

Screwdriver CRT
Support
Alligator Clip
Fig. 1-4
GND on the CRT Fig. 1-1
4. Insert one end of the Anode Support into the anode button,
2. Flip up the sides of the Rubber Cap in the direction of the then the other as shown in Fig. 1-5.
arrow and remove one side of the support.
(Refer to Fig. 1-2.)

Rubber Cap

Support
CRT
Fig. 1-5
CRT
Support 5. Confirm that the Support is securely connected.
Fig. 1-2
6. Put on the Rubber Cap without moving any parts.

B1-1
 DISASSEMBLY INSTRUCTIONS
2. REMOVAL AND INSTALLATION OF 3. When IC starts moving back and forth easily after
desoldering completely, pickup the corner of the IC using a
FLAT PACKAGE IC tweezers and remove the IC by moving with the IC
desoldering machine. (Refer to Fig. 2-3.)
REMOVAL
NOTE
1. Put the Masking Tape (cotton tape) around the Flat
Some ICs on the PCB are affixed with glue, so be
Package IC to protect other parts from any damage. careful not to break or damage the foil of each IC leads
(Refer to Fig. 2-1.) or solder lands under the IC when removing it.
NOTE
Masking is carried out on all the parts located within 10 Blower type IC
mm distance from IC leads. desoldering
machine

Masking Tape IC
(Cotton Tape)

Tweezers

Fig. 2-1
IC
Fig. 2-3
2. Heat the IC leads using a blower type IC desoldering
machine. (Refer to Fig. 2-2.)
4. Peel off the Masking Tape.
NOTE
Do not add the rotating and the back and forth 5. Absorb the solder left on the pattern using the Braided
directions force on the IC, until IC can move back and Shield Wire. (Refer to Fig. 2-4.)
forth easily after desoldering the IC leads completely. NOTE
Do not move the Braided Shield Wire in the vertical
direction towards the IC pattern.
Blower type IC
desoldering machine

Braided Shield Wire

Soldering Iron

IC
IC pattern
Fig. 2-2 Fig. 2-4

B2-1
 DISASSEMBLY INSTRUCTIONS
INSTALLATION 4. When bridge-soldering between terminals and/or the
soldering amount are not enough, resolder using a Thin-tip
1. Take care of the polarity of new IC and then install the new Soldering Iron. (Refer to Fig. 2-8.)
IC fitting on the printed circuit pattern. Then solder each
lead on the diagonal positions of IC temporarily.
(Refer to Fig. 2-5.)
Thin-tip Soldering Iron IC

Soldering Iron

Fig. 2-8

5. Finally, confirm the soldering status on four sides of the IC

Solder temporarily Solder temporarily
using a magnifying glass.
Confirm that no abnormality is found on the soldering
Fig. 2-5 position and installation position of the parts around the IC.
If some abnormality is found, correct by resoldering.
2. Supply the solder from the upper position of IC leads NOTE
sliding to the lower position of the IC leads.
When the IC leads are bent during soldering and/or
(Refer to Fig. 2-6.)
repairing, do not repair the bending of leads. If the
bending of leads are repaired, the pattern may be
damaged. So, always be sure to replace the IC in this
case.

Solder Soldering Iron

IC Supply soldering
from upper position
to lower position

Fig. 2-6

3. Absorb the solder left on the lead using the Braided Shield
Wire. (Refer to Fig. 2-7.)
NOTE
Do not absorb the solder to excess.

Soldering Iron
IC

Braided Shield Wire

Fig. 2-7

B2-2
 SERVICE MODE LIST
This unit provided with the following SERVICE MODES so you can repair, examine and adjust easily.
To enter the Service Mode, press both set key and remote control key for more than 2 seconds.

Set Key Remocon Key Operations

VOL. (-) MIN 0 Releasing of V-CHIP PASSWORD.
Initialization of the factory.
NOTE: Do not use this for the normal servicing.
VOL. (-) MIN 1
If you set a factory initialization, the memories are reset such as the channel setting,
and the POWER ON total hours.
POWER ON total hours is displayed on the screen.
Refer to the "CONFIRMATION OF HOURS USED".
VOL. (-) MIN 6
Can be checked of the INITIAL DATA of MEMORY IC.
Refer to the "WHEN REPLACING EEPROM (MEMORY) IC".
Display of the Adjustment MENU on the screen.
VOL. (-) MIN 9
Refer to the "ELECTRICAL ADJUSTMENT" (On-Screen Display Adjustment).

CONFIRMATION OF HOURS USED

POWER ON total hours can be checked on the screen. Total hours are displayed in 16 system of notation.
NOTE: If you set a factory initialization, the total hours is reset to "0".
ADDRESS DATA
1. Set the VOLUME to minimum.
2. Press both VOL. DOWN button on the set and Channel
button (6) on the remote control for more than 2 seconds.
3. After the confirmation of using hours, turn off the power. INIT 00 50 Initial setting content of MEMORY IC.
CRT ON 0010 POWER ON total hours.
= (16 x 16 x 16 x thousands digit value)
+ (16 x 16 x hundreds digit value)
+ (16 x tens digit value)
FIG. 1 + (ones digit value)

WHEN REPLACING EEPROM (MEMORY) IC

If a service repair is undertaken where it has been required to change the MEMORY IC, the following steps should be taken to
ensure correct data settings while making reference to TABLE 1.
NOTE: No need setting for after INI 0F due to the adjustment value.

INI +0 +1 +2 +3 +4 +5 +6 +7 +8 +9 +A +B +C +D +E +F
00 50 04 EB 4E 57 B3 24 69 39 00 0C 05 90 AE 00 07

Table 1
1. Enter DATA SET mode by setting VOLUME to minimum.
2. Press both VOL. DOWN button on the set and Channel button (6) on the remote control for more than 2 seconds.
ADDRESS and DATA should appear as FIG 1.
3. ADDRESS is now selected and should "blink". Using the VOL. +/- button on the remote, step through the ADDRESS until
required ADDRESS to be changed is reached.
4. Press ENTER to select DATA. When DATA is selected, it will "blink".
5. Again, step through the DATA using VOL. +/- button until required DATA value has been selected.
6. Pressing ENTER will take you back to ADDRESS for further selection if necessary.
7. Repeat steps 3 to 6 until all data has been checked.
8. When satisfied correct DATA has been entered, turn POWER off (return to STANDBY MODE) to finish DATA input.
After the data input, set to the initializing of shipping.
9. Turn POWER on.
10. Press both VOL. DOWN button on the set and Channel button (1) on the remote control for more than 2 seconds.
11. After the finishing of the initializing of shipping, the unit will turn off automatically.
The unit will now have the correct DATA for the new MEMORY IC.

C-1
 ELECTRICAL ADJUSTMENTS
1. ADJUSTMENT PROCEDURE 2. BASIC ADJUSTMENTS
Read and perform these adjustments when repairing the
circuits or replacing electrical parts or PCB assemblies. 2-1: CUT OFF

CAUTION 1. Adjust the unit to the following settings.

• Use an isolation transformer when performing any service R.DRIVE=10, B.DRIVE=10, R.BIAS=64, G.BIAS=64,
on this chassis. B.BIAS=64, BRI.CENT=100, CONT.MAX=60.
• Before removing the anode cap, discharge electricity 2. Place the set with Aging Test for more than 15 minutes.
because it contains high voltage. 3. Activate the adjustment mode display of Fig. 1-1 and
• When removing a PCB or related component, after press the channel button (01) on the remote control to
unfastening or changing a wire, be sure to put the wire select "CUT OFF".
back in its original position. 4. Adjust the Screen Volume until a dim raster is obtained.
• When you exchange IC and Transistor for a heat sink,
2-2: WHITE BALANCE
apply the silicon grease on the contact section of the heat
sink. Before applying new silicon grease, remove all the NOTE: Adjust after performing CUT OFF adjustment.
old silicon grease. (Old grease may cause damages to the 1. Place the set with Aging Test for more than 10 minutes.
IC and Transistor.) 2. Receive the gray scale pattern from the Pattern Generator.
Prepare the following measurement tools for electrical 3. Using the remote control, set the brightness and contrast
adjustments. to normal position.
1. Oscilloscope 4. Activate the adjustment mode display of Fig. 1-1 and
2. Digital Voltmeter press the channel button (10) on the remote control to
3. Pattern Generator select “R. BIAS”.
5. Press the CH. UP/DOWN button on the remote control to
On-Screen Display Adjustment select the “R. BIAS”, “G. BIAS”, “B. BIAS”, “R. DRIVE” or
1. In the condition of NO indication on the screen. “B. DRIVE”.
Press the VOL. DOWN button on the set and the Channel 6. Adjust the VOL. UP/DOWN button on the remote control
button (9) on the remote control for more than 2 seconds to whiten the R. BIAS, G. BIAS, B. BIAS, R. DRIVE, and
to appear the adjustment mode on the screen as shown in B. DRIVE at each step tone sections equally.
Fig. 1-1. 7. Perform the above adjustments 5 and 6 until the white
color is looked like a white.

TV 2-3: FOCUS
1. Receive the monoscope pattern.
2. Turn the Focus Volume fully counterclockwise once.
3. Adjust the Focus Volume until picture is distinct.

00 OSD 28 2-4: HORIZONTAL PHASE

Fig. 1-1 1. Receive the monoscope pattern.
2. Using the remote control, set the brightness and contrast
3. Use the Channel UP/DOWN button or Channel button to normal position.
(0-9) on the remote control to select the options shown 3. Activate the adjustment mode display of Fig. 1-1 and
in Fig. 1-2. press the channel button (05) on the remote control to
4. Press the MENU button on the remote control to end the select “H. PHAS”.
adjustments. 4. Press the VOL. UP/DOWN button on the remote control
until the SHIFT quantity of the OVER SCAN on right and
NO. FUNCTION NO. FUNCTION left becomes minimum.
00 OSD H 16 CONTRAST CENT
01 CUT OFF 17 CONTRAST MAX 2-5: VERTICAL SHIFT
04 H. VCO 18 CONTRAST MIN
1. Receive the monoscope pattern.
05 H. PHASE 19 COLOR CENTER
06 V. SIZE 20 COLOR MAX
2. Using the remote control, set the brightness and contrast
07 V. SHIFT 21 COLOR MIN to normal position.
08 R DRIVE 22 TINT 3. Activate the adjustment mode display of Fig. 1-1 and
09 B DRIVE 23 SHARPNESS press the channel button (07) on the remote control to
10 R BIAS 24 FM LEVEL select “V. SFT”.
11 G BIAS 25 LEVEL 4. Press the VOL. UP/DOWN button on the remote control
12 B BIAS 26 SEPARATION1 until the horizontal line becomes fit to the notch of the
13 BRIGHT CENT 27 SEPARATION2
shadow mask.
14 BRIGHT MAX 28 TEST MONO
15 BRIGHT MIN 29 TEST STEREO
Fig. 1-2

D-1
 ELECTRICAL ADJUSTMENTS
2-6: VERTICAL SIZE
1. Receive the monoscope pattern.
2. Using the remote control, set the brightness and contrast
to normal position.
3. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (06) on the remote control to
select “V. SIZE”.
4. Press the VOL. UP/DOWN button on the remote control
until the SHIFT quantity of the OVER SCAN on upside and
downside becomes 10 ± 2%.

2-7: SUB BRIGHTNESS white 100% red 120% Fig. 2-2

1. Receive the monoscope pattern. (RF Input)
2. Using the remote control, set the brightness and contrast 2-9: SUB CONTRAST
to normal position.
3. Activate the adjustment mode display of Fig. 1-1 and 1. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (13) on the remote control to press the channel button (17) on the remote control to
select "BRI.CENT". select “CONT. MAX”.
4. Press the VOL. UP/DOWN button on the remote control 2. Press the VOL. UP/DOWN button on the remote control
until the white 10% is starting to be visible until the contrast step No. becomes “60”.
5. Receive the monoscope pattern. (Audio Video Input) 3. Receive a broadcast and check if the picture is normal.
6. Press the TV/VIDEO button on the remote control to set 4. Press the TV/VIDEO button on the remote control to set to
to the AV mode. Then perform the above adjustments the AV mode. Then perform the above adjustments 1~3.
2~4.
2-10: OSD HORIZONTAL
2-8: SUB TINT/SUB COLOR 1. Activate the adjustment mode display of Fig. 1-1.
1. Receive the color bar pattern. 2. Press the VOL. UP/DOWN button on the remote control
2. Connect the oscilloscope to TP023. until the difference of A and B becomes minimum.
3. Activate the adjustment mode display of Fig. 1-1 and (Refer to Fig. 2-3)
press the channel button (22) on the remote control to
select "TINT".
4. Press the VOL. UP/DOWN button on the remote control TV
until the section "A" becomes as straight line
(Refer to Fig. 2-1)
5. Connect the oscilloscope to TP022.
6. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (19) on the remote control to
select "COL.CENT". 00 OSD 28
7. Press the VOL. UP/DOWN button on the remote control
until the red color level is adjusted to 120 ± 5% of the
A B Fig. 2-3
white level. (Refer to Fig. 2-2)
8. Receive the color bar pattern. (Audio Video Input)
9. Press the TV/VIDEO button on the remote control to set 2-11: Confirmation of Fixed Value (Step No.)
to the AV mode. Then perform the above adjustments
2~7 Please check if the fixed values of the each adjustment
items are set correctly referring below. (RF/AV)
NO. FUNCTION STEP NO.
04 H. VCO 04
14 BRIGHT MAX 183
15 BRIGHT MIN 60
16 CONTRAST CENT 30
18 CONTRAST MIN 17
20 COLOR MAX 74
"A" 21 COLOR MIN 00
23 SHARPNESS 45
24 FM LEVEL 00
25 LEVEL 00
Fig. 2-1 26 SEPARATION1 00
27 SEPARATION2 00

D-2
 ELECTRICAL ADJUSTMENTS
3. PURITY AND CONVERGENCE 3-3: STATIC CONVERGENCE
ADJUSTMENTS NOTE
NOTE Adjust after performing adjustments in section 3-2.
1. Turn the unit on and let it warm up for at least 30 1. Receive the crosshatch pattern from the color bar
minutes before performing the following adjustments. generator.
2. Place the CRT surface facing east or west to reduce the 2. Combine red and blue of the 3 color crosshatch
terrestrial magnetism. pattern on the center of the screen by adjusting the pair
3. Turn ON the unit and demagnetize with a Degauss Coil. of 4 pole magnets.
3. Combine red/blue (magenta) and green by adjusting the
3-1: STATIC CONVERGENCE (ROUGH ADJUSTMENT) pair of 6 pole magnets.
1. Tighten the screw for the magnet. Refer to the adjusted
3-4: DYNAMIC CONVERGENCE
CRT for the position. (Refer to Fig. 3-1)
If the deflection yoke and magnet are in one body, NOTE
untighten the screw for the body. Adjust after performing adjustments in section 3-3.
2. Receive the green raster pattern from the color bar
generator. 1. Adjust the differences around the screen by moving the
3. Slide the deflection yoke until it touches the funnel side deflection yoke upward/downward and right/left.
of the CRT. (Refer to Fig. 3-2-a)
4. Adjust center of screen to green, with red and blue on 2. Insert three wedges between the deflection yoke and
the sides, using the pair of purity magnets. CRT funnel to fix the deflection yoke.
5. Switch the color bar generator from the green raster (Refer to Fig. 3-2-b)
pattern to the crosshatch pattern. RGB RGB
6. Combine red and blue of the 3 color crosshatch
pattern on the center of the screen by adjusting the pair
of 4 pole magnets. R
7. Combine red/blue (magenta) and green by adjusting the G
pair of 6 pole magnets. B R
8. Adjust the crosshatch pattern to change to white by
G
repeating steps 6 and 7.
B
UPWARD/DOWNWARD SLANT RIGHT/LEFT SLANT
3-2: PURITY
NOTE Fig. 3-2-a

Adjust after performing adjustments in section 3-1.

1. Receive the green raster pattern from color bar generator.
2. Adjust the pair of purity magnets to center the color on
the screen.
Adjust the pair of purity magnets so the color at the ends WEDGE WEDGE
are equally wide.
3. Move the deflection yoke backward (to neck side)
slowly, and stop it at the position when the whole screen
is green.
4. Confirm red and blue color.
5. Adjust the slant of the deflection yoke while watching the WEDGE
screen, then tighten the fixing screw.
DEFLECTION YOKE WEDGE POSITION
DEFLECTION YOKE SCREW Fig. 3-2-b
MAGNET SCREW

PURITY MAGNETS
6 POLE MAGNETS
4 POLE MAGNETS
Fig. 3-1

D-3
 ELECTRICAL ADJUSTMENTS
4. ELECTRICAL ADJUSTMENT PARTS LOCATION GUIDE (WIRING CONNECTION)

CRT PCB

CP806

R8
B
03

0 3
P8

R8
TP022

0 7
CP803A TU001
FB401 TP023

01

01
4
CP

J8
CP802B
CP801

CD801
CR
T
DY

GND CRT
DEGAUSS COIL
L503

CP502

S501B
CD501
CP802A

AC IN
S501A

CD101B

CD101A SPEAKER

MAIN PCB

D-4
 BLOCK DIAGRAM

TU001

10 11 12 13 17
CH. DOWN
IC1001 AN7511
VOL. DOWN
2 6
21 20 34 SPEAKER
SOUND AMP
CH. UP SP1001
4 IC 8
66 ATT
VOL. UP RGB Proc.2
73 OSD SW Q801
67 CONTRAST BRIGHTNESS 50 RED OUT
POWER Chroma RGB OUTPUT Stage
68 Proc. DRIVE 51
Q802
I/O ACC/C-BPF CUT OFF
69 52
OS101 IIC APC/KILLER HV BLK GREEN OUT
70 RGB Proc.1 MCU
TIM TINT/DEMO
1 RGB MATRIX CLK Q607
74 INT
COLOR CONT Q803
PWM H-CTL
78 BLUE OUT
AD
76 Ver.Proc. Hor.Proc.
OSD
Ver SYNC SEP 46
D106 Q105 SYNC SEPA/Hor. VCO
Ver.COUNT DOWN 45
SW ROM Hor.COUNT DOWN
V RAMP
RAM AFC-1/H COINCIDENT Q402
J703 AFC-2 H PHASE H. DRIVE

2 Q401
VCXO H. OUTPUT
J702

2
56 58 57 27 26 37 38 16 3 9 7
MICON/CHROM IC
IC101 OEC7091C X601 B G R
Q505 3.579545MHz V801
Heater
P. FAIL
V-OUT IC 4 F 8
IC501 IC401 LA78040N-E
T502 LTV-817M-VB Q507 5 6
FEED BACK MEMORY IC PUMP UP
16 4 FEED BACK SW SDA SCL IC199
BR24L02F-WE2 -
AMP
8 Q502 +
DEGAUSS COIL
BUFFER L503 VCC
13
7 1 3 6 5 DY
6
Q501 D501~D504
POWER AMP RECTIFIER FB401

9
Q503 1 F
PROTECT DRV. 2 S
L501 10 HV
2 4
3
1 3

F501

AC IN
E-1 E-2
 PRINTED CIRCUIT BOARDS
MAIN/CRT (INSERTED PARTS)
SOLDER SIDE

D408

D404
C406
CP601
R403

R429
C435

HEATER
W003 D410

CD803A

GND

AFC
ABL
CP803A

D411

180V
W002 D405

W008 R410
W007
C403

8V
TU001
C448_1

12V
CP4
01

T401

25V

COL
C434

+B
C007
D001
D412
C43
7 C401 FB401 R421

R404
C440_1
R408

C004
C44 W001
W062 Q402 3 L401 R503 D506
W011 R542
HS402

D512
D409
HS501 B503

D509
1

R409
R446 40
S
H

Q401
R448 C511

R427
D406
1 Q502
40 R506 C527
IC

R401
C446

W827

Q501
R449 R520

W004
W010

R508
C516 C510
R417
W072 R504

C51
B502
W009 D516 R510_1
C002

4
R418
R424 47 C509
R4

D508 T502
W804

R413

C414
D513

R501
C417_1

R405

C526
R509
W039
W038
R514
C422

IC501
C427 C418

D502
C521

W037
R415

R416
W015

C506
D503

W829
C517_1

D501
R422
W036

L001_1
R002

D403
R001 W834
W050

D504
W006
D505
R527_1
C508 C503
W049 C515 CP502
Q503 D510

CMD009A
C502
Q602 R445 C507
W048 Q601 D528
C518

W802
Q603 W005
C617 R523_1 W014 R518
W831 R516 R6
29

TH501_1
TP401 R507 D511_1
R528

W019
W046 W067 W817 CP503
R513

1
C606

R515
W012

17_

D515
R537_1
R602 R505 R52
W035

W070

R608

R5
W034
Q505 5
R603 R512
W809

D507

L501
C601 D521 R502

C513
C106 C519
W832

C447_1 W025

D514
W833
R423
D606

05

RISK
Q606

R8
W843
W040
W073

C103 R519
R604

W024 Q507

C
X601 C602 C623

P8
R119
R130

03

03
W065 D522
W023

R8

OF FIRE - REPLACE AS MARKED.

C605
W059

4
02

F501 FH502
D602 W069 R804 CP806 R538

C
TP
W058

D
80
W064 W020
C615_1

3B
W057 R605 TP022 C8
19
R601

W816 Q802_1 W071 _1 C505

W056

07
W054 IC1001
C621

Q801_1 R802

R8
C634_1
W055 W018 S501B

J8
C616
C620_1

TP023

01
W803
W017

C622 C809
W053 C610 C628 W823 R815
C1005

R816 Q803_1
R606 W828 C1003 R811

FH501

R5
C630
W052
W051

D604
C624_1

C808 C810

00
R621 W033
W068 R813
CD802A

W061 R607

S501A
R809 R814
CP802A

R1001

CD501
W032
R611

C1001 R806
R620

R614
W045
W044
W043

W031
D603 W066

R613 CP802B
Q105
R615 W030
R617

CD802B
W028

Q607 C633 W812

R616

W029

CCD004A
R112
R113

CP801_1

W807
W027

R121
C123 W026
CD101B

W808
R110
R109

OS101
W042

C118
W041

C614

D106_1
CD101A
J703 J702
C612 SW101 SW102 SW103 SW104 SW105
R704_2

W060
W811

R701

F-1 F-2
F-3
C501
CCD004A
R101

R1005
SOLDER SIDE

C1004
R419 R1008
R1004
R420

C001 R1003 R126

R116 R143
R115
PRINTED CIRCUIT BOARDS
MAIN (CHIP MOUNTED PARTS)

R004 R003

R107
R128

R106
R125 R618
R124
R127
C629
R105

R129
64
R108

1
R627
R609

IC
10
1 C627
41

C626
C102 C112
R610

R103
25

C105 C104
R102
IC199_1

C107
C108_1
C101 R703
C603
R702

R104 C604

C609

CMD009A
F-4
 A B C D E F G H

MICON/CHROMA/TUNER SCHEMATIC DIAGRAM

IC199_1 BR24L02F-WE2
0 0 0 0
1 2 3 4
(MAIN PCB)

VSS
E1

E2
E0
MEMORY IC
8 8

50V 10 KA
C633
MODE
VCC

SDA
SCL
R621 4.9 5

47K 1/4W
8 7 6 5
4.9 0 4.8 4.8

R617
220 1/4W H.CTL

2.2K 1/2W
5.6 Q607

R620
KTC3198

W808
R618

P.CON+5V
P.CON+5V

W823
22K

W828

H_OUT
3

H_CTL
FROM/TO DEFLECTION/CRT
C118

H_SYNC
R608

11E1-EIC ABCL
H_CTL

G.OUT

R.OUT
B.OUT
7 6.3V 100 KA 2 CLAMP 7
R110 1K 1/4W
P.CON+B
C101
R109 10K 1/4W V_OUT

100 1/4W
0.01 F

100 1/4W

100 1/4W
10K 1/4W GND
C630

10K
R610
V_FEEDBACK
AT+5V

D606

F
10V 470 YK

10K 1/4W

63V 1 MKT
F
ABCL

C112
R124

100P CH

C626
R105

C627
4.7K

R611

C624_1
H_OUT

0.01
0.01
50V 1 KA
R609

120K
10K C629

R615

C628
R614

R613
SDA X-RAY
1 CNVSS 41 NC 0.01 F

1K 1/4W
R616
R130 R.OUT

R108
R106

R107
4.7K

100
100
2 XIN 42 HVCO F/B

R627
SCL G.OUT

10K
10K 1/4W 5 6 7
3 XOUT 43 AFC FILTER C623
B.OUT
NC
4 TEST1 44 DEF GND 0 0 0 0 0 4.9 0.3 4.9 0 4.6 NC 2.3 3.2 3.2 3.5 8.0 0 8.0 4.6 4.9 0 3.4 3.7 0 NC
H_SYNC
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 50V 2.2 KA 7.9
5 VSS 45 FBP IN
6 R119 4.9 8.8 R607
8V REG 6
6 MCU VCC 46 H OUT 8.5 Q606

65

40
KTC3203_Y
7 TEST0 47 DEF VCC 22K 1/4W 4.6 100 1/4W
2.4 11.3
AFT MCU GND FROM/TO TV POWER

66

39
8 FILT 48 NC R112 4
2.2K 1/4W Ver.Proc. UNREG+12V
9 HLT 49 HI VCC 4.9 IIC BUS Hor.Proc. 4.5
KEY1 PGB OUTPUT Stage Ver SYNC SEP V_OUT

67

38
10 VHOLD 50 R OUT R113 2.2K 1/4W DECODER DRIVE SYNC SEPA/Hor.VCO POWER_FAIL
Ver.COUNT DOWN 2.6
4.9 CUT-OFF Hor.COUNT DOWN R606
11 CVIN 51 G OUT KEY2 SDA/SCL AFC-1/H COINCIDENT V RAMP V_FEEDBACK UNREG+12V

68

37
R116 2.2K ROM HV BLK
AFC-2 H PHASE
12 RESET IN 52 B OUT
4.9 RAM OSD 0 22K 1/4W X-RAY
POWER_ON GND

69

36
13 MCU RESET OUT 53 ACL R115 22K
3.3 C622 C621 AT+5V
14 Y SW OUT 54 NC 4.9
REMOCON

70

35
15 V/C GND 55 PROTECT 0 I/O 4.0 50V 1 KA 16V 47 YK
16 3.58 XTAL 56 SDA AUDIO_OUT C620_1

71

34
NC RGB Proc.2
17 C-APC 57 H_CTL 4.9 OSD SW RGB Proc.1 4.6
5 1 0.01 B 5
72 RGB MATRIX

33
18 MCU5.7V REG OUT 58 SCL NC CONTRAST NC
P-ON CONT Power Manage. BRIGHTNESS COLOR CONT 3.1 D604
19 NC 59 NC 4.9 IIC D603
AUDIO_MUTE
73

32
MCU RESET NC FROM/TO SOUND/AV
20 CVBS IN3 60 NC
TIM 8.8 1SS133 MTZJ8.2B
2.9 R605
21 AUDIO IN3 61 NC X-RAY CCD
74

31
R125 INT Chroma Proc.
22 V/C VCC 62 DEGAUSS_H Vldeo Proc. P.CON+5V 220 1/2W AUDIO_MUTE
R127 4.9 ACC/C-BPF 2.0
47K IIC_OFF C-TRAP/YDELAY
75

30
23 MCU TEST 63 STANDBY_H PWM APC/KILLER NC TUNER+5V VIDEO_IN
SHARPNESS
1K 0 CLK CONT TINT/DEMO 2.3
24 CVBS IN2 64 VOLUME AD MCU BLACK STRETCH AUDIO_IN
ON_TIMER CPU core 5V REG
76

29
CLK Y MUTE NC
25 AUDIO IN2 65 NC Q602 4.9 AUDIO_OUT
0 5.7 R604 KTC3203_Y
26 CVBS IN1 66 AFT P.CON+5V
77

28
NC LPF
27 AUDIO IN1 67 KEY1 6bB AMP ATT C614 100 1/4W 5.5
4.9 2.3 7.2 R629 GND
POWER_FAIL AUDIO_IN
78

27
28 5.7V REG OUT 68 KEY2 C617
VCO 2.0 50V 1 KA
29 C(Y/C) IN 69 POWER_ON R129 0 XO 22 3W
C612 10V 100 YK 7.2
79

26
4 30 Y(Y/C) IN 70 REMOCON
47K 4.9 VIDEO_IN 5.5 4
VCXO 2.2 C001
31 VREG VCC 71 AV2
80

25

19

18
NC NC 50V 1 KA 5V REG 4.9
32 FSC OUT 72 AV1 Q603 NC 1 NC 0.01 F
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 KTC3203_Y C002
33 MONITOR OUT 73 AUDIO_MUTE
0 0 5.0 5.0 0 4.9 0 1.2 2.0 0.8 3.4 4.9 5.0 3.4 0 3.4 2.9 5.6 NC 0 2.9 2.8 5.0 0 NC 2.0 NC 2 NC
34 AUDIO ATT OUT 74 X-RAY MICON/CHROMA IC
L001_1

3.579545MHz
C108_1

C605 0.022 F 22P CH 100CT3R505

100 1/4W
F
6.3V 1000 YK
0.001 B

R602
IC101 TUNER+5V

C602
35 AUDIO ATT FILTER 75 IIC_OFF C615_1
C107 50V 1 KA
0.01 F

OEC7091C TUNER+5V 3
C106
C104

X601
0.1
C102 TU_VIDEO 3.3uH
36 TEST 3 76 ON_TIMER AT+5V
50V 1 Serr NC 4 NC

10V 100 YK
37 V RAMP F/B 77 SYNC 0.01 F

50V 1 KA
W833
R102

C105 1K

C601
D602
B

38 V RAMP OUT 78 POWER FAIL

C603
NC 5 NC
R103 470P B

C606
220P

39 V RAMP CAP 79 NC
W809

C609 MTZJ9.1B
16V 47 YK
C103

40 8.7V REG OUT 80 EXT_MUTE NC 6 NC

0.01 F
R104

C616
1M

C604
1K

TU_AUDIO
C610

8.2K 50V 1 KA
3 50V 1 KA 3
6.3V 47 KA NC 7 NC
W816

C634_1 NC 8 NC
5.1

1/4W
0 R601
ON_TIMER
0.027 B
NC 9 NC
SWITCHING
4.8 R004 TEST POINT
Q105 SCL 10 SCL
REMOCON

POWER_ON
KEY1

KRA102MAT
KEY2

AT+5V

R003 100 CP601 A2001WR2-6P

SDA 11 SDA
100 NC 6
12 AFT NC 5
AFT
25V 10 KA

IIC_OFF
R143 IIC_OFF 4
1/4W

TU_AUDIO SDA
TU_AUDIO 13 SDA 3
R121

47

0.022 B
SCL

C007
2 R128 SCL 2 2
270

5V REG NC 14 NC
GND 1
560 5.5 Q601 R002 R001
P.CON+B
C123

4.9 KTC3203_Y R603 P.CON+B 15

POWER ON/ON TIMER

R126 R101 15K 1/2W 15K 1/2W

8.8

F
SLR-342VCT32

120 1/2W

C004
2.7K 560 NC 16 NC

0.022
D106_1

4.9

4.8

VOL DOWN

TU001
EVQ21505R

EVQ21505R

EVQ21505R
0

EVQ21505R

EVQ21505R
CH DOWN

TU_VIDEO
SW101

SW103

SW104

POWER
VOL UP

115-V-KA35ARB TU_VIDEO 17
SW102

SW105
CH UP

MTZJ33B
B+ 3
GND 2
1

D001
Vout

20

21
PCB010
CMD009

OS101
RPM7138-WH5 CAUTION: DIGITAL TRANSISTOR R.SIGNAL
1 NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED CAUTION:SINCE THESE PARTS MARKED BY ARE
ATTENTION:LES PIECES REPAREES PAR UN ETANT G.SIGNAL 1
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST CRITICAL FOR SAFETY,USE ONES DANGEREUSES AN POINT DE VUE SECURITE B.SIGNAL
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. DESCRIBED IN PARTS LIST ONLY N’UTILISER QUE CELLS DECRITES
DANS LA NOMENCLATURE DES PIECES DEFLECTION SIGNAL
TUNER VIDEO SIGNAL
A B C D E F G H
G-1 G-2
 A B C D E F G H

TV POWER SCHEMATIC DIAGRAM

(MAIN PCB)
8 8

CAUTION :FOR CONTINUED PROTECTION AGAINST FIRE HAZARD,

REPLACE ONLY WITH THE SAME TYPE 4A 125V (F501)
FUSE.

4A 125V ATTENTION :POUR UNE PROTECTION CONTINUE LES RISQUES

D’INCEIE N’UTILISER QUE DES FUSIBLE DE MEME
TYPE 4A 125V (F501).

TO SOUND/AV

GND
R517_1
D505
SOUND+B
7 21DQ09N 3.3 1W 7

16V 1000 YK
C518

C519
500V 470P B

SOUND_GND

FROM/TO DEFLECTION/CRT
D510
+B

2.7M 1/2W
DEGAUSS COIL

+-10%
RU2AM-EIC

R500
L503 PROTECT DRIVE
8R200030 CP502 Q503 UNREG+12V
A1561WV2-2P 2SA1624
C517_1 W834

160V 100 MHE

1 135.0 0 P.CON+B
1

2KV 820P RR

100V 10 MHE
6 2
2

C521
W802 135.0

C507
R501 R514
R527_1
TH501_1
1 3.3 5W C 0.22 1W 5.6K
R523_1
B59203-S1060-B14 CP503

1N4005-EIC
003P-2100 47K

1N4005-EIC

D502
R525

200V 330 UP
D501

2.2M 1/2W
C526

R510_1
1.2 2W
GND
275V 0.22 ECQUL

B
1N4005-EIC
1.5M 1/2W

1/4W
B

500V 0.001
1N4005-EIC

C503
D503
4A 125V

R528
MTZJ18B
500V 0.001
C505

C502
R538

D504
3 4 T502 FROM/TO MICON/CHROMA/TUNER

0.0056 B

D509
5 5

C527
8129109S

6.8K
W832
F501 51MS040L 1 2 POWER_FAIL
4A125V
R537_1
D516 R504 D521 R505 0
COIL,LINE FILTER 1.7 10.0 4.9 X-RAY
4A125V L501 8 11 P.FAIL 10K 1/4W
FH501 FH502 1N4937 100 1/4W 1K 1/4W
MTZJ6.8B Q505

50V 10 YK
EYF-52BCY EYF-52BCY 1R0A562F20

1/4W
0 4.8 KTA1266

C516
NC
7 12

R516

10K
144.0 132.3 W829 D513
6 13 UNREG+12V

16V 2200 YK
21DQ09N
0

C515
W804

NC 5 14 AT+5V
AC120V_60Hz
CD501
09414909 S501A 10.3 0
4
W5RH3.5X5X1.0

15 GND
4 BLACK 4
6.6 11.3
B502
R

C506 3 16
BLADE
WIDE

WHITE S501B
C514

2KV 680P

250V 0.001 KX 10.3

144.0
2 17 NC
D R508
C509
G

1SS133
D512
4.8 220 1W 0.047 M 18 NC
W827

S
0.1

1SS133
POWER AMP

D515
100 1/4W
56K 1/4W

Q501
R503
R520

2SK3563(ORION_Q)
1SS133
D508
W5RH3.5X5X1.0

MTZJ2.2B
C511

D507
B503

100 1/4W
1/4W

3 BUFFER 50V 1 KA 3
R509
R506

Q502
MTZJ18B

KTC3198
1K

D506

1/2W
100 1/4W
4.8 0.1

R515
R502

F
C513
0.47 1W

0.0082 B
R542

120K
0.1
HS501
C501

0
763WSAA021
C508
9.5
6.0
250V 0.0047 KX
C510

1SS133

1SS133
FEED BACK

D514

D522
MTZJ3.9B
5.5 SWITCHING
0.033 B

D511_1

1/4W
Q507
KTC3198

R513
FEED BACK
IC501

2.2K
2 LTV-817M-VB 2
11.5 10.5 R512 R519
4

680 1/4W 1.2K 1/4W

100 1/4W
3

R507
0.1 9.5

MTZJ5.6B
D528

5.6K +-1%
R518
PCB010
CMD009

NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED
1 OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST CAUTION:SINCE THESE PARTS MARKED BY ARE ATTENTION:LES PIECES REPAREES PAR UN ETANT
DANGEREUSES AN POINT DE VUE SECURITE
1
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. CRITICAL FOR SAFETY,USE ONES
DESCRIBED IN PARTS LIST ONLY N’UTILISER QUE CELLS DECRITES
NOTE: THE RESISTOR MARKED F IS FUSE RESISTOR. DANS LA NOMENCLATURE DES PIECES
THE ALUMI ELECTROLYTIC CAPACITOR MARKED NP
IS NON POLAR ONE.
A B C D E F G H
G-3 G-4
 A B C D E F G H

FROM MICON/CHROMA/TUNER DEFLECTION/CRT SCHEMATIC DIAGRAM (MAIN PCB) GND

GND
CP802A
B2013H02-5P
1 1
CP802B
B2013H02-5P
GND
GND
CLAMP CLAMP
CLAMP CLAMP 2 2 CLAMP
G.OUT G.OUT
8 G.OUT G.OUT 3 3 G.OUT 8
R.OUT R.OUT
R.OUT R.OUT 4 4 R.OUT
B.OUT B.OUT
B.OUT B.OUT 5 5 B.OUT
V-OUT IC IC401 LA78040N-E
CP803A B2013H02-4P CP803B B2013H02-4P
HEATER HEATER
THERMAL HEATER 1 1 HEATER
PROTECTION GND GND
GND 2 2 GND
PUMP
UP AMP NC NC 3 3 NC NC
180V 180V
180V 4 4 180V

4.7K 1/4W
4.7K 1/4W

4.7K 1/4W
R811
R809

R814
1 2 3 4 5 6 7
3.5 25.0 2.0 0 12.0 25.0 3.5

35V 100
C414

YK
CP801_1

W843
7 CD801 A2361WV2-2P 7
8 RED OUT GREEN OUT BLUE OUT
R423 CH823004 Q801_1
1 1 Q802_1 Q803_1
12
D403 KTC4217
100 1/4W 2 2 KTC4217 KTC4217
13
R424 V801 3.2 3.2 3.2
11E1-EIC
A48LGS30X14AN35
100.6 98.4

330 1/2W
6.8K 1/4W 95.4

100V 0.15
C422

R410
MKT
9 2.7
2.7 2.7
10
R418 R420 R

330 1/4W
8

330 1/4W

390P B

330 1/4W
390P B

390P B
G

R813
25V 470 YK

R815

R816
6

680
R419

C809

C810
33K 1/4W 4.7K R415

C808
15K 1/4W
B

50V 10 YK

C418
11

R417

1 1/2W
1.8K 1/2W 5 7 1

C417_1

R416

50V 10 YK
2.2K 1/2W
R413
1.8 1/2W

C427
HS401 TO DY

R422
6 763WSAA021 6
5 14 15 16
CP401
4
A1561WV2-A5P
3 TP022 TP024 TP023

100V 22 YK
C434
R429 NC 2
1
3.9 1W
470 YK

12K 2W

1/4W

2.7K 1/4W
+-1%

2.7K 1/4W

12K 2W
MTZJ5.1B
C447_1

12K 2W
D411
D412

R408

2.7K
AU02A-EIC
16V

4.7K

R805

R807
R802

R804

R806
R803
FROM/TO MICON//CHROMA/TUNER
R401 R409
W831
5 X-RAY 5
27K +-1% 27K +-1%
P.CON+B

MHE
C401

250V 2.2
T401
9 ETH09K14BZ
3 4

4.7mH
250V 0.33 PMS

L401
NC 2
470 1/2W
R446

1 6
C437

GND
H.DRIVE
68 1/2W

V_FEEDBACK
Q402 10
R404

4 V_OUT 2SC1627_Y 4
27.0 FB401 FQI20B103_M
50V 22 YK

ABCL
11
H_OUT 130.0 COL
C446

0.3 1 HV
1.25KV 0.0066 MPP

H_SYNC 0 FOCUS
B
1/4W

130.0
C440_1

500V 0.0012

CP806
R405

H.OUTPUT
C443

FOCUS
100 1/4W

0 Q401 132.5 VIDEO F SCREEN

1K

0 6
R427

2SC5885

2KV 0.001 B
FROM/TO TV POWER
SCREEN

C819_1
132.5 B+ S
GND 2
HS402 GND 0
48.0 11
TP401 763WSAA028 AFC
9
HEA ABL 4.3 96.4
7.0 7
W817 10 TER
+B

9
0

8
3 GND 3
R403 8

7
NC 4 E12 101.6
22K 1/4W GND 0

F
6
8
P.CON+B 25.0 E25 0
3

1
C406

5
E8
5 NC 0 0

4
3
500V 100P B
6.4 99.6 J801
ISMS01S
MTZJ6.2B
D404

R447
D406 PCB110
UNREG+12V
CCD004
150 2W 11E1-EIC
AU02A-EIC
AU02A-EIC

2 2
D405

D410
11E1-EIC
D409

NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME NOTE: THE RESISTOR MARKED F IS FUSE RESISTOR.
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
THE ALUMI ELECTROLYTIC CAPACITOR MARKED NP
R449
NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED IS NON POLAR ONE.
680 1/2W WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST
R448 WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
680 1/2W R445
ATTENTION:LES PIECES REPAREES PAR UN ETANT
DANGEREUSES AN POINT DE VUE SECURITE
R.SIGNAL
35V 470 YK

250V 22 YK

150K 1/4W
100V 0.1

G.SIGNAL
220K 1/4W
C448_1

N’UTILISER QUE CELLS DECRITES

MHE

11E1-EIC
C403

C435

D408

1 DANS LA NOMENCLATURE DES PIECES 1

R421

PCB010
CMD009
B.SIGNAL
CAUTION:SINCE THESE PARTS MARKED BY
CRITICAL FOR SAFETY,USE ONES
ARE DEFLECTION SIGNAL
DESCRIBED IN PARTS LIST ONLY

A B C D E F G H
G-5 G-6
 A B C D E F G H

SOUND/AV SCHEMATIC DIAGRAM

8
(MAIN PCB) 8

ACCESSORY

RCA JACK WHITE

TO MICON/CHROMA/TUNER
J703
AV1-09AD-4 (FRONT) UM-4
19 R703 BT001

E
AUDIO 2 W811
7 AUDIO_IN A_IN GR03X-SP2 7

1
820
20 R704_2 UM-4

E
VIDEO 2 V_IN TM101 BT002
VIDEO_IN

1
10 1/4W RC-EH050(CT-859) GR03X-SP2

68 1/4W

R702

47K
R701
RCA JACK YELLOW
J702
AV1-09AD-3
GND

6 6

5 5

W807

W812
4 4
18
FROM TV POWER

SOUND_GND CD101A SPEAKER

C3013207
1 1
SOUND+B 2 2
CD101B
C3013206 SP1001
GND S08F21A
8.2 3.5 0 3.4
8 OHM

AN7511
5 6 7 8

SOUND AMP IC
+ -
3 3

IC1001
FROM MICON/CHROMA/TUNER
4 3 2 1
R1001 5.1 0 0.3 3.9
AUDIO_MUTE
47K 1/4W

R1003
P.CON+5V
68K

25V 10 KA
KA
C1003
R1004

C1005
R1005
100K

270K
W803

B
2 2

C1004
50V

0.0015
GND

R1008

39K
C1001 17
AUDIO_OUT
50V 0.1 KA PCB010
CMD009

1
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED
WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST
ATTENTION:LES PIECES REPAREES PAR UN ETANT CAUTION:SINCE THESE PARTS MARKED BY
CRITICAL FOR SAFETY,USE ONES
ARE TUNER VIDEO SIGNAL
1
DANGEREUSES AN POINT DE VUE SECURITE
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. N’UTILISER QUE CELLS DECRITES DESCRIBED IN PARTS LIST ONLY AUDIO SIGNAL
DANS LA NOMENCLATURE DES PIECES

A B C D E F G H
G-7 G-8
 WAVEFORMS
MICON/CHROMA/TUNER

1 0.5V 2ms/div 6 1V 20µs/div 11 200V 20µs/div

2 20V 20µs/div 7 1V 20µs/div 12 10V 5ms/div

DEFLECTION/CRT

3 200mV 20µs/div 8 0.5V 5ms/div 13 10V 5ms/div

4 0.5V 5ms/div 9 20V 20µs/div 14 50V 20µs/div

5 1V 20µs/div 10 2V 20µs/div 15 50V 20µs/div

NOTE: The following waveforms were measured at the point of the corresponding
balloon number in the schematic diagram.
H-1
 WAVEFORMS

16 50V 20µs/div

SOUND/AV

17 0.5V 1ms/div

18 1V 1ms/div

19 200mV 500µs/div

20 500mV 20µs/div
NOTE: The following waveforms were measured at the point of the corresponding
balloon number in the schematic diagram.
H-2
 MECHANICAL EXPLODED VIEW
202
103

202
102B

202
117

102B
201 102A

119
102

202
119 201
PCB110
201 (CRT PCB ASS'Y)
106 107
105

119

205

201
119
205

203

PCB010
(MAIN PCB ASS'Y)
204

101D 118
101B

104

101C

101
101A

I-1
 MECHANICAL EXPLODED VIEW
(PACKING DIAGRAM)

109 113, 114, 115,

TM101

109 109

109

108

111

116

110

110

I-2
 MECHANICAL REPLACEMENT PARTS LIST
Location No. TSB P/N Reference No. Description

101 AE006004 7A701A356A FRONT CABI ASS'Y

101A AE006173 701WPJC966 CABINET,FRONT
101B AE001500 713WPAA046 GLASS,LED
101C AD300694 713WPAA050 GUIDE,REMOCON
101D AE006174 735WPBB357 BUTTON,FRAME

102 AE005646 7A702A088A BACK CABI ASS'Y

102A AE006175 702WPAA844 CABINET,BACK
102B AE005648 800WQ0A091 FELT SHEET

103 AE005649 722549A413 SHEET,RATING

104 AE005650 723000C727 SHEET,CAUTION
105 AE005651 723000C778 FILM,DECORATION
106 BZ710660 741WUA0021 SPRING,EARTH
107 BZ710260 899HV3T000 HOLDER,ANODE WIRE
108 AE005652 791WHAA126 FILM BAG
109 AD300700 792WHAA054 PACKAGE,TOP

110 AD300701 792WHAA055 PACKAGE,BOTTOM

111 AE005653 793WCDC582 GIFT BOX
112 AE005654 A3M218S975 INSTRUCTION BOOK KIT
113 AE005715 JB5KD200 POLYBAG,INSTRUCTION(RED CAUTION)
114 AE006176 J3M21802A GUARANTEE CARD
115 AE006177 J3M21821B INSTRUCTION BOOK(E/S)
116 AE005656 723000C776 SHEET,BAR CODE
117 AE005657 726000A085 SHEET,CRT SERVICEMAN
118 AE006178 735WPAA938 HOLDER,SPEAKER
119 AD302158 800WR0A002 SHEET,CRT SUPPORT

201 AE005928 8160H50B8U SCREW,TAP TITE(P) W5x28

202 AE004847 8117540A6U SCREW,TAP TITE(B0) TRUSS 4x16
203 AE003531 810763080U SCREW,TAP TITE(S) BRAZIER 3x8
204 AE003528 8110630A0U SCREW,TAP TITE(P) BRAZIER 3x10
205 AE005659 8109I3080U SCREW,TAP TITE(B) WH7 3x8

J1-1
 ELECTRICAL REPLACEMENT PARTS LIST
Location No. TSB P/N Reference No. Description
RESISTORS
! R401 BZ210089 R4X5T6273F R,METAL 27K OHM 1/6W
! R404 AE001556 R615U2680J R,FUSE 68 OHM 1/2W
! R408 BZ210258 R4X5T6472F R,METAL 4.7K OHM 1/6W
! R409 BZ210089 R4X5T6273F R,METAL 27K OHM 1/6W
! R429 AE005886 R638813R9J R,FUSE 3.9 OHM 1W
! R447 BZ210229 R3X28A151J R,METAL OXIDE 150 OHM 2W
! R500 BZ210080 R0G3K2275K RC 2.7M OHM 1/2W
! R501 AD300652 R5X2CD3R3J R,CEMENT 3.3 OHM 5W
! R508 BZ210240 R3X181221J R,METAL OXIDE 220 OHM 1W
R509 AD301203 R002T4101J RC 100 OHM 1/4W
R510 AE003279 R00202225J RC 2.2M OHM 1/2W
! R514 AE005735 R63881R22J R,FUSE 0.22 OHM 1W
R515 BZ210081 R002T2124J RC 120K OHM 1/2W
! R517 AE001696 R3X1813R3J R,METAL OXIDE 3.3 OHM 1W
! R518 BZ210244 R4X5T6562F R,METAL 5.6K OHM 1/6W
! R519 BZ210124 R002T4122J RC 1.2K OHM 1/4W
! R525 AD301315 R3X18A1R2J R,METAL OXIDE 1.2 OHM 2W
! R538 BZ210206 R002T2155J RC 1.5M OHM 1/2W
! R542 BZ210251 R3X181R47J R,METAL OXIDE 0.47 OHM 1W
! R629 AE000081 R3X28B220J R,METAL OXIDE 22 OHM 3W
! R803 BZ210050 R3X18A123J R,METAL OXIDE 12K OHM 2W
! R805 BZ210050 R3X18A123J R,METAL OXIDE 12K OHM 2W
! R807 BZ210050 R3X18A123J R,METAL OXIDE 12K OHM 2W
CAPACITORS
! C403 BZ110149 E02LT4471M CE 470 UF 35V
C414 AD301434 E02LU4101M CE 100 UF 35V
! C418 BZ110041 E02LT3471M CE 470 UF 25V
! C434 BZ110195 E02LU8220M CE 22 UF 100V
C437 BZ110174 P4J7F3334J CMPP 0.33 UF 250V PMS
! C443 AE001548 P4N8FJ662H CMPP 0.0066UF 1.25KV
C446 BZ110205 E02LU5220M CE 22 UF 50V
! C448 BZ110204 E0ELFD220M CE 22 UF 250V
C503 BZ110061 C0JTB0513K CC 0.001 UF 500V B
! C505 BZ110025 P2122B224M CMP 0.22 UF 275V ECQUL
! C506 AD301026 CD39E0M13M CC 0.001 UF 250V
! C508 AE002878 CD39E0MQ3M CC 0.0047UF 250V
C514 BZ110172 C03L0R7U2K CC 680 PF 2KV R
! C515 BZ110135 E02L02222M CE 2200 UF 16V
! C517 BZ110203 C0PLRR7W2K CC 820 PF 2KV RR
! C519 BZ110207 E02LT2102M CE 1000 UF 16V
! C521 BZ110092 E5EZFB101M CE 100 UF 160V
! C526 AD301635 E51CGC331M CE 330 UF 200V
C527 79091377 CQGTB04S3K CC 0.0056UF 50V B
C615 AE003280 E52H05010M CE 1 UF 50V
C819 BZ110247 C0JBB0713K CC 0.001 UF 2KV B
DIODES
D001 BZ410037 D97U03301B DIODE,ZENER MTZJ33B T-77
D106 BZ410054 0021721150 LED SLR-342VCT32
D403 BZ410043 D2WT011E10 DIODE,SILICON 11E1-EIC
D404 BZ410066 D97U06R21B DIODE,ZENER MTZJ6.2B T-77
! D405 BZ410063 D2WTAU02A0 DIODE,SILICON AU02A-EIC
! D406 BZ410043 D2WT011E10 DIODE,SILICON 11E1-EIC
D408 BZ410043 D2WT011E10 DIODE,SILICON 11E1-EIC
D409 BZ410043 D2WT011E10 DIODE,SILICON 11E1-EIC
! D410 BZ410063 D2WTAU02A0 DIODE,SILICON AU02A-EIC
! D411 BZ410063 D2WTAU02A0 DIODE,SILICON AU02A-EIC
! D412 BZ410020 D97U05R11B DIODE,ZENER MTZJ5.1B T-77
! D501 BZ410085 D2WXN40050 DIODE,SILICON 1N4005-EIC
! D502 BZ410085 D2WXN40050 DIODE,SILICON 1N4005-EIC
! D503 BZ410085 D2WXN40050 DIODE,SILICON 1N4005-EIC
! D504 BZ410085 D2WXN40050 DIODE,SILICON 1N4005-EIC
! D505 BZ410010 D28T21DQN9 DIODE,SCHOTTKY 21DQ09N-TA2B1
D506 AD300671 D97U01801B DIODE,ZENER MTZJ18B T-77
D507 BZ410067 D97U02R21B DIODE,ZENER MTZJ2.2B T-77
D508 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77
! D509 AD300671 D97U01801B DIODE,ZENER MTZJ18B T-77
! D510 BZ410080 D2WXRU2AM0 DIODE,SILICON RU2AM-EIC
D511 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77
! D512 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77
! D513 BZ410010 D28T21DQN9 DIODE,SCHOTTKY 21DQ09N-TA2B1
D514 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77

J2-1
 ELECTRICAL REPLACEMENT PARTS LIST
Location No. TSB P/N Reference No. Description
DIODES
D515 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77
D516 AD300731 D2WXN49370 DIODE,SILICON 1N4937
D521 BZ410022 D97U06R81B DIODE,ZENER MTZJ6.8B T-77
D522 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77
D528 BZ410021 D97U05R61B DIODE,ZENER MTZJ5.6B T-77
D602 BZ410023 D97U09R11B DIODE,ZENER MTZJ9.1B T-77
D603 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77
D604 BZ410058 D97U08R21B DIODE,ZENER MTZJ8.2B T-77
D606 BZ410043 D2WT011E10 DIODE,SILICON 11E1-EIC
ICS
IC101 AE005644 I56F07091C IC OEC7091C
IC199 AE005642 A3M218S015 INIT DATA BR24L02F-WE2
! IC401 AE002783 I03TD804N0 IC LA78040N-E
! IC501 BZ410088 0002E00610 PHOTO COUPLER LTV-817M-VB
! IC1001 BZ611001 I01DP75110 IC
TRANSISTORS
Q105 BZ510086 TPATB03003 COMPOUND TRANSISTOR KRA102MAT
! Q401 AE000656 TC1G058850 TRANSISTOR,SILICON 2SC5885
! Q402 BZ510089 TC5T01627Y TRANSISTOR,SILICON 2SC1627_Y(TPE2)
! Q501 AE002251 T25F035630 FET 2SK3563(ORION_Q)
! Q502 BZ510069 TCATC31980 TRANSISTOR,SILICON KTC3198-AT(Y,GR)
! Q503 BZ510004 TA3T016240 TRANSISTOR,SILICON 2SA1624-AA
Q505 BZ510073 TAATA12660 TRANSISTOR,SILICON KTA1266-AT(Y,GR)
Q507 BZ510069 TCATC31980 TRANSISTOR,SILICON KTC3198-AT(Y,GR)
Q601 BZ510070 TCAT032034 TRANSISTOR,SILICON KTC3203_Y-AT
Q602 BZ510070 TCAT032034 TRANSISTOR,SILICON KTC3203_Y-AT
Q603 BZ510070 TCAT032034 TRANSISTOR,SILICON KTC3203_Y-AT
Q606 BZ510070 TCAT032034 TRANSISTOR,SILICON KTC3203_Y-AT
Q607 BZ510069 TCATC31980 TRANSISTOR,SILICON KTC3198-AT(Y,GR)
! Q801 BZ510091 TCA0042170 TRANSISTOR,SILICON KTC4217(O,Y)
! Q802 BZ510091 TCA0042170 TRANSISTOR,SILICON KTC4217(O,Y)
! Q803 BZ510091 TCA0042170 TRANSISTOR,SILICON KTC4217(O,Y)
COILS &TRANSFORMERS
L001 BZ310136 021LA63R3K COIL 3.3 UH
L401 AD301644 021L75472J COIL 4.7 MH
! L501 AD301395 029T000104 COIL,LINE FILTER 1R0A562F20
! L503 AE001529 028R200030 COIL,DEGAUSS 8R200030
T401 BZ310157 045009003J TRANS,HORIZONTAL DRIVE ETH09K14BZ
! T502 AE001531 048129109S TRANSFORMER,SWITCHING 8129109S
JACKS
J702 AE005633 060Q401112 RCA JACK AV1-09AD-3
J703 AE005632 060Q401111 RCA JACK AV1-09AD-4
! J801 BZ614434 066F120018 SOCKET,CATHODE RAY TUBE ISMS01S
SWITCHES
SW101 BZ612010 0504101T34 SWITCH,TACT EVQ21505R
SW102 BZ612010 0504101T34 SWITCH,TACT EVQ21505R
SW103 BZ612010 0504101T34 SWITCH,TACT EVQ21505R
SW104 BZ612010 0504101T34 SWITCH,TACT EVQ21505R
SW105 BZ612010 0504101T34 SWITCH,TACT EVQ21505R
P.C.BOARD ASSEMBLIES
PCB010 AE005641 A3M218S010 PCB ASS'Y CMD009A
PCB110 AE005643 A3M218S110 PCB ASS'Y CCD004A
MISCELLANEOUS
B502 BZ310121 024HT03553 CORE,BEADS W5RH3.5X5X1.0
B503 BZ310121 024HT03553 CORE,BEADS W5RH3.5X5X1.0
BT001 AE005640 141R004016 BATTERY,MANGAN GR03X-SP2
BT002 AE005640 141R004016 BATTERY,MANGAN GR03X-SP2
! CD501 AE005639 1209414909 CORD,AC BUSH 9414909
CD801 AE005637 06CH823004 CORD,CONNECTOR CH823004
CD802 BZ614310 WCL6844038 FLAT CABLE AWM2468 A WG26 5C GRAY 440MM
CD803 BZ614493 WBL6032038 FLAT CABLE AWM2468 A WG26 4C BLACK 320MM
! CP401 BZ614303 069S450089 CONNECTOR PCB SIDE A1561WV2-A5P
! CP502 BZ614283 069S420110 CONNECTOR PCB SIDE A1561WV2-2P
CP503 BZ614016 069W01001A CONNECTOR PCB SIDE 003P-2100
CP601 AE005634 069S260639 CONNECTOR PCB SIDE A2001WR2-6P
CP801 BZ614269 069S320010 CONNECTOR PCB SIDE A2361WV2-2P
CD101A AE005636 06C3013207 CORD,CONNECTOR C3013207
CD101B AE005635 06C3013206 CORD,CONNECTOR C3013206
CP802A BZ614276 067U005049 WIRE HOLDER B2013H02-5P
CP802B BZ614276 067U005049 WIRE HOLDER B2013H02-5P
CP803A BZ614334 067U004029 WIRE HOLDER B2013H02-4P

J2-2
 ELECTRICAL REPLACEMENT PARTS LIST
Location No. TSB P/N Reference No. Description
MISCELLANEOUS
CP803B BZ614334 067U004029 WIRE HOLDER B2013H02-4P
EL001 BZ614043 124116281A EYE LET XRY16X28BD
EL002 BZ614044 124120301A EYE LET XRY20X30BD
! F501 AD302166 081PC04005 FUSE 51MS040L
! FB401 AE003283 043220061F TRANSFORMER,FLYBACK FQI20B103_M
FH501 AE002634 06710T0009 HOLDER,FUSE EYF-52BCY
FH502 AE002634 06710T0009 HOLDER,FUSE EYF-52BCY
OS101 AD301048 0773071001 REMOTE RECEIVER RPM7138-WH5
! SP1001 AE005722 070Y132027 SPEAKER S08F21A
! TH501 AD302000 D8EE0B1400 DEGAUSS ELEMENT B59203-S1060-B14
TM101 AD301335 076N0EH020 TRANSMITTER RC-EH020
! TU001 AE006069 0163300018 RF UNIT 115-V-KA35ARB
! V801 AE005638 098Y200495 CRT W/DY A48LGS30X14AN35
X601 BZ613004 100CT3R505 CRYSTAL HC-49/U

RESISTOR
RC................... CARBON RESISTOR

CAPACITORS
CC................... CERAMIC CAPACITOR
CE................... ALUMI ELECTROLYTIC CAPACITOR
CP................... POLYESTER CAPACITOR
CPP.................. POLYPROPYLENE CAPACITOR
CPL.................. PLASTIC CAPACITOR
CMP...................... METAL POLYESTER CAPACITOR
CMPL................ METAL PLASTIC CAPACITOR
CMPP................ METAL POLYPROPYLENE CAPACITOR

J2-3
 TOSHIBA CORPORATION
1-1, SHIBAURA 1-CHOME, MINATO-KU, TOKYO 105-8001, JAPAN