4.

Troubleshooting

4. Troubleshooting
4-1. Troubleshooting
1. Check the various cable connections first.
• Check to see if there is a burnt or damaged cable.
• Check to see if there is a disconnected or loose cable connection.
• Check to see if the cables are connected according to the connection diagram.
2. Check the power input to the Main Board.

4-1
4. Troubleshooting

4-1-1. No Power
-- The LEDs on the front panel do not work when connecting the power cord.
Symptom -- The SMPS relay does not work when connecting the power cord.
-- The units appears to be dead.
The IP relay or the LEDs on the front panel does not work when connecting the power cord if the cables are
improperly connected or the Main Board or SMPS is not functioning. In this case, check the following:
Major -- Check the internal cable connection status inside the unit.
checkpoints -- Check the fuses of each part.
-- Check the output voltage of SMPS.
-- Replace the Main Board.

Lamp(Backlight) Off, Change power cable.

No
power indicator LED on ? LC350_26", 32" : BN39-01278A

Yes

Does proper Stand-By DC No

A5V appear at TP - A5V?
Change Main Power Assy.
Yes LC350_26": BN44-00368A
Diagnostics LC350_32" : BN41-00369A
Does proper Main No
DC B12V, B13V, B5V appear at
TP - B12V, B13V, B5V?
Yes

Does proper DC A3.3V No

appear at TP - A3.3V?
Change the Main Assy.
Yes LC350_26",32" : BN94-02649A

Does proper DC B3.3V, B9V, DDR1.9V, No

A1.2V, appear at
TP - B3.3V, B9V, 1.9V, L101?
Yes

Change the LVDS Cable

26" : BN96-12469B No
Check "No video."
32" : BN96-12469C
Lamp(Backlight) on, no video ?

Caution Make sure to disconnect the power before working on the IP board.

4-2
 4. Troubleshooting

Location (Main)

TOP BOTTOM

C
A

D
B

Detail

B5V

A B B13V
A1.26
B3.3V
B9V

A13V A5V A5V

C D

A3.3V

4-3
4. Troubleshooting

4-1-2. No Video (Analog PC signal)

Symptom -- Audio is normal but no picture is displayed on the screen.

-- Check the PC source

Major -- Check the Saturn4(IC201).
checkpoints
-- This may happen when the LVDS cable connecting the Main Board and the Panel is disconnected.

Power indicator LED is off. No Check if the set is in

Lamp(Backlight) on, no video ? ‘Stand-by mode’ or *DPMS mode.’
Yes

Check the PC source and No Insert the analog PC signal properly.

check the connection of D-SUB ?
Yes

Does the signal appear at Check CN804, PC cable.

1 TP - 821, 823, 825, 826, 828 No Change the Main Assy.
(R, G, B, H, V) of IC201? LC350_26": BN44-00368A
Diagnostics LC350_32" : BN41-00369A
Yes

Check IC201 (Saturn4).

Does the digital data appear at
2 No Change the Main Assy.
Pin #16,17 (LVDS Data clk)
LC350_26": BN44-00368A
of LVDS connector?
LC350_32" : BN41-00369A

Yes

Check the LVDS cable? No Please, Contact Tech support.

Replace the LCD panel?

* DPMS Mode : Display Power management Signaling mode.

- If PC is power off in TV's PC mode, TV SET will be DPMS Mode.
- It is similar TV's Stand by mode. (Turn off Backlight, Function LED is blinking)

Caution Make sure to disconnect the power before working on the IP board.

4-4
 4. Troubleshooting

Location (Main)

TOP BOTTOM

Detail

TP821 TP825 TP828

TP823 TP826
A B LVDS CLK-

LVDS CLK+

4-5
4. Troubleshooting

„„ WAVEFORMS

1 PC input (V-sink, H-sink, R/G/B )

2 LVDS output

4-6
 4. Troubleshooting

4-1-3. No video (HDMI - Digital signal)

Symptom -- Audio is normal but no picture is displayed on the screen.

-- Check the HDMI source

Major
-- Check the Saturn4(IC201)
checkpoints
-- This may happen when the LVDS cable connecting the Main Board and the Panel is disconnected.

Power indicator LED is off. No Check if the set is in

Lamp(Backlight) on, no video ? 'Stand-by mode.'
Yes

Check the HDMI source and

No
check the connection of HDMI cable ? Insert the HDMI signal properly.
Diagnostics
Yes

Does the signal appear at Check CN803, CN801.

CN803 (Pin#12, #7 )(HDMI1) No Check HDMI cable.
3 Change the Main Assy.
CN801 (Pin#12, #7 )(HDMI2)
(HDMI RX_Clk, RX_Data)? LC350_26": BN44-00368A
LC350_32" : BN41-00369A
Yes

Does the digital data appear at Check IC201 (Saturn4).

Pin #16,17 (LVDS Data clk) No Change the Main Assy.
2
of LVDS connector? LC350_26": BN44-00368A
LC350_32" : BN41-00369A
Yes

Check the LVDS cable? No

Replace the LCD panel? Please, Contact Tech support.

Caution Make sure to disconnect the power before working on the IP board.

4-7
4. Troubleshooting

Location (Main)

TOP BOTTOM

A
B

Detail

Pin#12 Pin#7
A B LVDS CLK-

LVDS CLK+

4-8
 4. Troubleshooting

„„ WAVEFORMS

3 HDMI input (RX_Data, RX_Clk)

2 LVDS output

4-9
4. Troubleshooting

4-1-4. No Video (Tuner_CVBS)

Symptom -- Audio is normal but no picture is displayed on the screen.

-- Check the Tuner CVBS source

Major
-- Check the Tuner (TU601)
checkpoints
-- This may happen when the LVDS cable connecting the Main Board and the Panel is disconnected.

Power indicator LED is off. No Check if the set is in

Lamp(Backlight) on, no video ? 'Stand-by mode.'
Yes

Check the HDMI source and

No
check the connection of HDMI cable ? Insert the RF source properly.
Yes
Diagnostics
No Change the Main Assy.
Does the DC TU5V_PW, TU33V_PW LC350_26": BN44-00368A
appear at #2, #4 Pin of Tuner? LC350_32" : BN41-00369A

Yes
Check Tuner.
Does the CVBS data appear at No Change the Main Assy.
4
#8 pin of Tuner? LC350_26": BN44-00368A
LC350_32" : BN41-00369A
Yes

Does the digital data appear at Check IC201 (Saturn4).

2 Pin #16,17 (LVDS Data clk) No Change the Main Assy.
of LVDS connector? LC350_26": BN44-00368A
LC350_32" : BN41-00369A

Yes

Check the LVDS cable? No

Replace the LCD panel? Please, Contact Tech support.

Caution Make sure to disconnect the power before working on the IP board.

4-10
 4. Troubleshooting

Location (Main)

TOP BOTTOM

Detail

#2 TU5V #8 CVBS
A B LVDS CLK-

#4 TU33V

LVDS CLK+

4-11
4. Troubleshooting

„„ WAVEFORMS

4 CVBS OUT (Grey Bar)

2 LVDS output

4-12
 4. Troubleshooting

4-1-5. No Video (Tuner DTV)

Symptom -- Audio is normal but no picture is displayed on the screen.

-- Check the DTV source

Major
-- Check the Tuner (TU601)
checkpoints
-- This may happen when the LVDS cable connecting the Main Board and the Panel is disconnected.

Power indicator LED is off. No Check if the set is in

Lamp(Backlight) on, no video ? 'Stand-by mode.'
Yes

No
Check the connection of RF cable ? Insert the RF cable properly.

Yes
Diagnostics
Check the ‘signal strength’ No
in Self Diagnosis menu Check the D-TV source.
Strength is enough?

Yes

Does the DC TU5V_PW, TU33V_PW No Change the Main Assy.

appear at #2, #4 Pin of Tuner? LC350_26": BN44-00368A
LC350_32" : BN41-00369A
Yes

Does the digital data appear at Check IC201 (Saturn4).

2 Pin #16,17 (LVDS Data clk) No Change the Main Assy.
of LVDS connector? LC350_26": BN44-00368A
LC350_32" : BN41-00369A
Yes

Check the LVDS cable? No

Replace the LCD panel? Please, Contact Tech support.

Caution Make sure to disconnect the power before working on the IP board.

4-13
4. Troubleshooting

Location (Main)

TOP BOTTOM

Detail

#2 TU5V
A B LVDS CLK-

#4 TU33V

LVDS CLK+

4-14
 4. Troubleshooting

„„ WAVEFORMS

2 LVDS output

4-15
4. Troubleshooting

4-1-6. No Video (Video CVBS)

Symptom -- Audio is normal but no picture is displayed on the screen.

-- Check the Video CVBS source

Major
-- Check the Saturn4 (IC201)
checkpoints
-- This may happen when the LVDS cable connecting the Main Board and the Panel is disconnected.

Power indicator LED is off. No Check if the set is in

Lamp(Backlight) on, no video ? 'Stand-by mode.'
Yes

Check the video source and No Insert the video source properly.
Diagnostics
check the connection of video cable ?
Yes
Check CN704.
Does the CVBS data appear at No Change the Main Assy.
4
COMP_YCVBS? LC350_26": BN44-00368A
LC350_32" : BN41-00369A
Yes

Does the digital data appear at Check IC201 (Saturn4).

No Change the Main Assy.
2 Pin #16,17 (LVDS Data clk)
of LVDS connector? LC350_26": BN44-00368A
LC350_32" : BN41-00369A
Yes

Check the LVDS cable? No

Replace the LCD panel? Please, Contact Tech support.

Caution Make sure to disconnect the power before working on the IP board.

4-16
 4. Troubleshooting

Location (Main)

TOP BOTTOM

Detail

A B LVDS CLK-

COMP_YCVBS
LVDS CLK+

4-17
4. Troubleshooting

„„ WAVEFORMS

4 CVBS OUT (Grey Bar)

2 LVDS output

4-18
 4. Troubleshooting

4-1-7. No Video (Component)

Symptom -- Audio is normal but no picture is displayed on the screen.

-- Check the Component source

Major
-- Check the Saturn4(IC201)
checkpoints
-- This may happen when the LVDS cable connecting the Main Board and the Panel is disconnected.

Power indicator LED is off. No Check if the set is in

Lamp(Backlight) on, no video ? 'Stand-by mode.'
Yes

No Insert the component

Check the component source and
source properly.
check the connection of
Diagnostics component cables(Y,Pb,Pr)?

Yes
Check CN705.
Does the component data appear at
No Change the Main Assy.
5 COMP_YCVBS, COMP_PB,
LC350_26": BN44-00368A
COMP_PR ?
LC350_32" : BN41-00369A
Yes

Check IC201 (Saturn4).

Does the digital data appear at
No Change the Main Assy.
2 Pin #16,17 (LVDS Data clk)
LC350_26": BN44-00368A
of LVDS connector?
LC350_32" : BN41-00369A
Yes

Check the LVDS cable? No

Please, Contact Tech support.
Replace the LCD panel?

Caution Make sure to disconnect the power before working on the IP board.

4-19
4. Troubleshooting

Location (Main)

TOP BOTTOM

Detail

A B LVDS CLK-
COMP_YCVBS COMP_PR

LVDS CLK+
COMP_PB

4-20
 4. Troubleshooting

„„ WAVEFORMS

5 Compnent_Y (Gray scale) / Pb / Pr (Color bar)

2 LVDS output

4-21
4. Troubleshooting

4-1-8. No Sound

Symptom -- Video is normal but there is no sound..

-- When the speaker connectors are disconnected or damaged.

Major
-- When the sound processing part of the Main Board is not functioning.
checkpoints
-- Speaker defect..

Check the source and

No Insert the sound source properly.
check the connection of sound cable
(Comp/PC/DVI to HDMI)?
Yes

Check CN706,CN805.
Does the sound data appear at Change the Main Assy.
No
COMP_SR/COMP_SL LC350_26": BN44-00368A
TP830,831(PC,DVI sound R/L)? LC350_32" : BN41-00369A

Diagnostics
Yes

Change the Main Assy.

Does the DC B3.3V, B12V No LC350_26": BN44-00368A
appear at TP - B3.3V, B12V? LC350_32" : BN41-00369A

Yes

Check IC903 (Audio CODEC).

No Change the Main Assy
6 Does the I2C data appear at R1004? LC350_26": BN44-00368A
LC350_32" : BN41-00369A
Yes

Check IC201 (Saturn4).

Does the sound data appear at No Check IC903 (Sound AMP).
7 Change the Main Assy
Speaker - L-, L+, R-, R+?
LC350_26": BN44-00368A
Yes LC350_32" : BN41-00369A

Replace speaker ? No
LC350_26",32" : BN96-13058A Please, Contact Tech support.

Caution Make sure to disconnect the power before working on the IP board.

4-22
 4. Troubleshooting

Location (Main)

TOP BOTTOM

B
A

Detail

R1004 TP830
Speaker R+ (PC,DVI sound R)

A Speaker R- B TP831
(PC,DVI sound R)

Speaker L+
Speaker L-

C
COMP_SR COMP_SL

4-23
4. Troubleshooting

WAVEFORMS

6 I2C Data

7 Speaker out

4-24
 4. Troubleshooting

4-2. Alignments and Adjustments

4-2-1. General Alignment Instructions
1. Usually, a color LCD-TV needs only slight touch-up adjustment upon installation.
Check the basic characteristics such as height, horizontal and vertical sync.
2. Use the specified test equipment or its equivalent.
3. Correct impedance matching is essential.

4. Avoid overload. Excessive signal from a sweep generator might overload the front-end of the TV.
When inserting signal markers, Do not allow the generator to distort the result.

5. Connect the TV only to an AC power source with voltage and frequency as specified on the backcover nameplate.

6. Do not attempt to connect or disconnect any wire while the TV is turned on.
Make sure that the power cord is disconnected before replacing any parts.

7. To protect against shock hazard, use an isolation transformer.

4-25
4. Troubleshooting

4-3. Factory Mode Adjustments

4-3-1 Entering Factory Mode with Factory Remote-control
1. Turn the power on LCD TV SET.
2. To enter `Service Mode' Press the remote -control keys in this sequence
info  factory key
3. If you want exit Factory mode, press 'Factory' key in Remote-cotrol.

4-3-2 Entering Factory Mode with Customer Remote-control

Using the Customer Remote
1. Turn the power off and set to stand-by mode
2. Press the remote buttons in this order; MUTE  1  8  2  POWER ON to turn the set on.

MUTE 1 8 2 Power On

3. The set turns on and enters service mode. This may take approximately 20 seconds.
4. Press the Power button to exit and store data in memory.
- If you fail to enter service mode, repeat steps 1 and 2 above.
5. Initial SERVICE MODE DISPLAY State
6. If you wnat exit Factory mode, Turn the power off LCD TV Set by remote control or Power code.
Option
ADC/WB
Control
Advanced
T-SAT4AUSHC-XXXX
DTP-LP-App-XXXX-XX
ADC : HDMI X COMP X PC X AV X
EDID : SUCCESS
HDCP : SUCCESS
Build Date : XX-XX-XXXX
Date Of Purchase : XX/XX/XX

* How to enter the hidden factory mode.

a. Into the factory mode
b. Highlight Advanced
c. Key input : 0 + 0 + 0 + 0
** hidden menu : Advanced

6. Buttons operations withn Service Mode

Menu Full Menu Display/Move to Parent Menu

Direction Keys / Item Selection by Moving the Cursor

Direction Keys / Data Increase / Decrease for the Selected Item

Source Cycles through the active input source that are connected to the unit

4-26
 4. Troubleshooting

4-3-3 Factory Data

Option Factory Name Data Range
Factory Reset
19O6TH0C, 19A6TH0C, 22P6TH0C, 22D6TH0C, 22I6TH0C,
Type
22A6TH0C, 26P6AH0C, 26I6AH0C, 32P6AH0C, 32O6AH0C
Model LC350
TUNER Xugang
Region US
DDR Etron
Front color S-C-GRAY

ADC/WB Factory Name

ADC
ADC Tarhet
ADC RESULT
WB

ADC Factory Name Data Range

AV Calibration Success Success / Failure
Comp Calibration Success Success / Failure
PC Calibration Success Success / Failure
HDMI Calibration Success Success / Failure

ADC Target Factory Name Data Range

1st_AV_Low 18 0 ~ 255
1st_AV_High 220 0 ~ 255
1st_AV_Delta 1 0 ~ 255
1st_COMP_Low 16 0 ~ 255
1st_COMP_High 235 0 ~ 255
1st_COMP_Delta 1 0 ~ 255
1st_PC_Low 2 0 ~ 255
1st_PC_High 253 0 ~ 255
1st_PC_Delta 1 0 ~ 255
2nd_Low 1 0 ~ 255
2nd_High 235 0 ~ 255
2nd_Delta 1 0 ~ 255

4-27
4. Troubleshooting

ADC Mode
RESULT Factory Name Range
HDMI COMP PC AV
1st_AV_Gain 127 127 127 127 0 ~ 255
1st_AV_Offset 139 139 139 139 0 ~ 255
1st_Comp_Gain 68 68 68 68 0 ~ 255
1st_Comp_Gain_Cb 68 68 68 68 0 ~ 255
1st_Comp_Gain_Cr 68 68 68 68 0 ~ 255
1st_Comp_Offset 127 127 127 127 0 ~ 255
1st_Comp_Offset_Cb 127 127 127 127 0 ~ 255
1st_Comp_Offset_Cr 127 127 127 127 0 ~ 255
1st_PC_R_Gain 96 96 96 96 0 ~ 255
1st_PC_G_Gain 95 95 95 95 0 ~ 255
1st_PC_B_Gain 94 94 94 94 0 ~ 255
1st_PC_R_Offset 127 127 127 127 0 ~ 255
1st_PC_G_Offset 127 127 127 127 0 ~ 255
1st_PC_B_Offset 127 127 127 127 0 ~ 255
2nd_R_Offset 113 113 113 113 0 ~ 255
2nd_G_Offset 113 113 113 113 0 ~ 255
2nd_B_Offset 113 113 113 113 0 ~ 255
2nd_R_Gain 145 145 145 145 0 ~ 255
2nd_G_Gain 145 145 145 145 0 ~ 255
2nd_B_Gain 144 144 144 144 0 ~ 255

WB Mode
Factory Name
AV COMP HDMI /DTV PC
Sub Brightness 128 128 128 128
R_Offset 124 124 124 124
G_Offset 128 128 128 128
B_Offset 128 128 128 128
Sub Contrast 134 134 134 134
R_Gain 133 133 133 133
G_Gain 128 128 128 128
B_Gain 141 141 141 141
Movie R Offset 123 123 123 123
Movie B Offset 127 127 127 127
Movie R Gain 144 144 144 144
Movie B Gain 67 67 67 67

4-28
 4. Troubleshooting

Control Factory Name

EDID
Sub Option
PDP Option
Hotel Option
Shop Option
Sound
Test Pattern

*EDID Factory Name Data Range

EDID ON/OFF Off On / Off
EDID WRITE ALL Success Success / Failure
EDID WRITE PC Success Success / Failure
EDID WRITE DVI Success Success / Failure
EDID WRITE HDMI1 Success Success / Failure
EDID WRITE HDMI2 Success Success / Failure
EDID WRITE HDMI3 Failure Success / Failure
EDID WRITE HDMI4 Failure Success / Failure
EDID VERSION HDMI 1.3 HDMI 1.2 / HDMI 1.3

* EDID Rewrite method

a. into the factory mode.
b. Enter Factory Menu 'Control \ EDID'.
c. Change 'EDID ON/OFF : OFF ==> ON ' by Direction keys '▶'.
d. Change 'EDID WRITE ALL ==> success' by Direction keys '▶' again.
f. Change 'EDID ON/OFF : ON ==> OFF ' by Direction keys '▶'.

Sub Option Factory Name Data Range

Panel Display Time XHr
Dimm Type EXT INT / EXT / INT_NEG / INT_POS / EXT_NEG
Watchdog On On / Off
LVDS Format JEIDA JEDIA / VESA

4-29
4. Troubleshooting

Hotel Factory Name Data Range

Option
Hotel Mode Off On / Off
Power On Channel 3
Power On Band Air Air / STD / HRC / IRC
Power On Source ATV ATV/DTV / Comp1 / PC / HDMI1 / HDMI2
Power On Volume 10
Min Volume 0
Max Volume 100
Panel Button Lock Off On / Off
Pic Menu Lock Off On / Off
Music Mode (AV) Off On / Off
Music Mode (PC) Off On / Off
Music Mode (Comp) Off On / Off
Music Mode Backlight Off On / Off
Menu Display On On / Off
Power On Option Last Option Standby / Power On / Last Option
Ch Remap On/Off
Program Ch
Original Ch/Src
Auto PC Off On / Off
Energy Saving Off Off / Low / Mid / High / Auto
Cloning : TV to USB
Cloning : USB to TV
Welcome Message

Shop Factory Name Data Range

Option
Shop Mode Off On / Off
USB DEMO ON (SEC)
USB DEMO OFF (SEC)

TEST Factory Name Data Range

Pattern
Mstar Test Pattern Off Off
FBE Test Pattern Off Off
LOGIC Test Pattern Off Off

Sound Factory Name Data Range

Carrier Mute Thr High [H-dev] 0x39 0x39
Carrier Mute Thr Low [H-dev] 0x26 0x26
SPEAKER EQ On On
Audio Delay 20mS 20mS

4-30
 4. Troubleshooting

Advanced Factory Name

ADJUST

ADJUST Factory Name Data Range

Uart Select Auto Wall Auto Wall / Debug / MDC / On1 / On2

4-31
4. Troubleshooting

4-4. White Balance - Calibration

4-4-1 White Balance -Calibration

1. Calibration AV Calibration
Comp Calibration
PC Calibration
HDMI Calibration

4-4-2 Service Adjustment

You must perform Calibration in the Lattice Pattern before adjusting the White Balance.

„„ Color Calibration
Adjust spec.
1. Source : HDMI
2. Setting Mode : 1280*720@60Hz
3. Pattern : Pattern #24 (Chess Pattern)

( Chess Pattern )

4. Use Equipment : CA210 & Master MSPG925 Generator

- Use other equipment only after comparing the result with that of the Master equipment.

Input mode Calibration Pattern

CVBS IN (Model_#1) Perform in NTSC B&W Pattern #24 Lattice
Component IN (Model_#6) Perform in 720p B&W Pattern #24 Lattice
Perform in VESA XGA (1024x768)
PC Analog IN (Model_#21) Lattice
B&W Pattern #24
HDMI IN Perform in 720p B&W Pattern #24 Lattice

<Table 1>

4-32
 4. Troubleshooting

„„ Method of Color Calibration (AV)

1) Apply the NTSC Lattice (N0. 3) pattern signal to the AV IN 1 port
2) Press the Source key to switch to “AV1" mode
3) Enter Service mode
4) Select the “Calibration" menu
5) Select the “AV Calibration" menu.
6) In “AV Calibration Off" status, press the “ " key to perform Calibration.
7) When Calibration is complete, it returns to the high-level menu.
8) You can see the change of the “AV Calibration" status from Failure to Success.

„„ Method of Color Calibration (Component)

1) Apply the 720p Lattice (N0. 6) pattern signal to the Component IN 1 port
2) Press the Source key to switch to “Component1" mode
3) Enter Service mode
4) Select the “Calibration" menu
5) Select the “Comp Calibration" menu.
6) In “Comp Calibration Off" status, press the “ " key to perform Calibration.
7) When Calibration is complete, it returns to the high-level menu.
8) You can see the change of the “Comp Calibration" status from Failure to Success.

„„ Method of Color Calibration (PC)

1) Apply the VESA XGA Lattice (N0. 21) pattern signal to the PC IN port
2) Press the Source key to switch to “PC" mode
3) Enter Service mode
4) Select the “Calibration" menu
5) Select the “PC Calibration" menu.
6) In “PC Calibration Off" status, press the “ " key to perform Calibration.
7) When Calibration is complete, it returns to the high-level menu.
8) You can see the change of the “PC Calibration" status from Failure to Success.

„„ Method of Color Calibration (HDMI)

1) Apply the 720p Lattice (N0. 6) pattern signal to the HDMI1/DVI IN port
2) Press the Source key to switch to “HDMI1" mode
3) Enter Service mode
4) Select the “Calibration" menu
5) Select the “HDMI Calibration" menu.
6) In “HDMI Calibration Off" status, press the “ " key to perform Calibration.
7) When Calibration is complete, it returns to the high-level menu.
8) You can see the change of the “HDMI Calibration" status from Failure to Success.

4-4-3 White Balance - Adjustment

(low light) (hight light)

Sub Bright Sub Contrast

3. W/B
R offset R gain
G offset G gain
B offset B gain

(W/B adjustment Condition refer next page)

4-33
4. Troubleshooting

4-5. White Ratio (Balance) Adjustment

1. You can adjust the white ratio in factory mode (1:Calibration, 3:White-Balance).
2. Since the adjustment value and the data value vary depending on the input source, you have to
adjust these in CVBS, Component 1 and HDMI 1 modes.
3. The optimal values for each mode are configured by default. (Refer to Table 1, 2)
It varies with Panel’s size and Specification.

- Equipment : CS-210
- Pattern: MIK K-7256 #92 “Flat W/B Pattern" as standard
- Use other equipment only after comparing the result with
that of the Master equipment.
- Set Aging time : 60min

- Calibration and Manual setting for WB adjustment.

HDMI : Calibration at #24 Chessboard Pattern Manual adjustment #92 pattern (720p)
COMP: Calibration at #24 Chessboard Pattern Manual adjustment at #92 pattern (720p)
CVBS: Calibration at #24 Chessboard Pattern Manual adjustment at #92 pattern (NTSC)
- If finishing in HDMI mode, adjustment coordinate is almost same in AV/COMP mode.
- White Balance Manual Adjustment

4-34
 4. Troubleshooting

Adjustment Coordinate
P-Mode
x y Y(Luminance) T(K) + MPCD
26" - Sub_CT:135 Fix
CVBS H/L 272 278 12,000 (+10)
32" - Sub_CT:135 Fix
(NTSC)
L/L 272 278 Sub_Br:128 Fix 12,000 (+10)
26" - Sub_CT:135 Fix
COMP H/L 272 278 12,000 (+10)
32" - Sub_CT:135 Fix
(720P)
L/L 272 278 Sub_Br:128 Fix 12,000 (+10)
26" - Sub_CT:135 Fix
HDMI H/L 272 278 12,000 (+10)
32" - Sub_CT:135 Fix
(720P)
L/L 272 278 Sub_Br:128 Fix 12,000 (+10)

- Adjustment Specification
White Balance : High light (±2), Low light (±3)
Luminance : High light (Don’t care), Low light (±0.2 Ft/L)

4-6. Servicing Information

4-6-1 USB Download Method
Samsung may offer upgrades for TV’s firmware in the future. Please contact the Samsung call center at 1-800-
SAMSUNG (726-7864) to receive information about downloading upgrades and using a USB drive. Upgrades will be
possible by connecting a USB drive to the USB port located on your TV.

1. Insert a USB drive containing the firmware upgrade into the

USB port on the rear of the TV.
2. Press the MENU button to display the menu.
Press the or button to select “Support", then press the
ENTER button.
3. Press the or button to select “SW Upgrade", then press
the ENTER button.
The message “Scanning for USB. It may take up to 30
seconds." is displayed.
4. The message “Upgrade version XXXX to version XXXX?
The system will be reset after upgrade." is displayed.
Press the or to select the “OK", then press the ENTER
button.
Please be careful to not disconnect the power or remove the
USB drive while upgrades are being applied. The TV will turn off
and turn on automatically after completing the firmware upgrade.
Please check the firmware version after the upgrades are
complete. When software is upgraded, video and audio settings
you have made will return to their default (factory) settings.
We recommend you write down your settings so that you can
easily reset them after the upgrade.

4-35