Technical Paper

July 2019

Properties of Hard Surfacing Alloy

Ni-15Cr-15W-3B-4Si-3.5Fe-0.6C
(Colmonoy® 88)

Authors:
Michael Weinstein, Technical Services Manager, USA
BS, Metallurgical Engineering

Lydia Lee, Director of Brazing Engineering Center, USA

MBA, BSE, and MS, Engineering

Lawrence Johnson, Technical Services Engineer, USA

BS, Materials Engineering
Abstract Along with abrasion resistance some other physical
Colmonoy 88 is a hard surfacing alloy designed to
® properties of the coatings, cladding and/or weld
extend the life of OEM parts which are subject to various deposits were measured and are reported here.
wear mechanisms in service. It can also be used to
repair/rebuild worn parts subject to wear mechanisms Test procedures used include Abrasion testing by
and significantly extend their service life. ASTM G65, Vickers hardness by ASTM E-92, Rockwell
hardness by ASTM E18 as well as metallographic
This hard surfacing alloy can be applied by various examples of the test specimens. SEM was also used
methods including; Thermal Spray processes, such with EDS to measure iron content in some of the
as Sprayweld™, Laser Cladding, PTA welding, GTAW, coatings/deposits.
GMAW, and HVOF. This paper will compare the
properties of this alloy applied by different methods The Standard Test Method for Measuring Abrasion
using various test procedures and the relative cost to using the Dry Sand/Rubber Wheel Apparatus (ASTM
benefit associated therein. G65-16) was used to measure volume loss of the
surfacing materials. Procedure A of the Method uses a
130 N (13.6 kg (30 lbs) ) force holding the test specimen
Introduction against the rubber wheel for 6000-wheel revolutions.
Thermal spraying dates back to the early 1900’s. During this 30-minute period AFS 50/70 mesh test
Arc welding processes date back to the early 1800’s. sand (150 x 425 µm) test sand feeds between the wheel
Earlier metal joining processes (soldering and welding) and the specimen at ~350 g/min. A schematic of the
are not relevant to this study. Surfacing technologies/ test apparatus is shown in Figure 1.2, 3
processes include: Plating; Dip, Barrier and Chemical
Conversion Coatings; Thermal Spray; Chemical Vapor
Deposition (CVD); Plasma-Enhanced Chemical Vapor
Deposition (PECVD or PVD); and Diffusion Coatings1.
The purpose of hard surfacing, in this context, is
to improve the performance of a part in service
and/or restore dimensions and usability of a part
subject to wear. This study compares the abrasive
wear resistance of Colmonoy® 88 applied by several
processes suitable for the alloy’s available forms.

These processes are:

1. Conventional thermal spraying of powder using

oxygen and acetylene with Spraywelder™ System.

2. Laser cladding with powder.

3. Plasma Transferred Arc (PTA) welding with powder.

Figure 1. ASTM G65 apparatus
4. Weld surfacing using rod by the Gas Tungsten Arc
Welding (GTAW) process.

5. Weld surfacing using cored wire by the

Gas Metal Arc Welding (GMAW) process.

6. Thermal spraying of powder by the High Velocity

Oxygen Fuel (HVOF) process.

WALLCOLMONOY 2
Coatings/Deposits of Colmonoy® 88 were applied
to specimens of approximately 25 x 75mm and were
prepared using each process under evaluation.
Approximate deposition rates are shown in Figure 2.

Approximate
Alloy Deposit
Deposition Comments
Type
Rate (g/min)

Spraywelder™ Spraywelder, Model J-3

System 140 Oxygen-Acetylene
(Thermal Spray) Fused Coating

Weld Tech 3500D

PTA 25 Weld Overlay Figure 4. ASTM G65 wear test results
Two Layers
Laser Clad Overlay The average volume loss excluding the HVOF coating
Laser 25
1.2 kw @ 1000mm/min is 21.7 ± 1.5mm3. The difference between the unfused
GTAW (TIG)
20
Weld Overlay, 1.5 kw HVOF coating and the fused/welded overlays will be
Rod Two Layers addressed in the Discussion section. For reference;
GMAW (MIG)
40
Weld Overlay, 8.5 kw hardened D-2 tool steel is used as a standard for ASTM
Wire Two Layers G65. Interlaboratory test results indicate a procedure
HVOF 80
JP 5000 HVOF Coating A volume loss of 35.6 ± 5.2mm3. The laboratory control
Not Fused test measured D-2 tool steel volume loss of 35.3mm3,
Figure 2. Process summary which is within the expected standard range. Thus,
validating this series of tests. Fused and welded
The compositions of the nickel-based alloy feed stock overlays of Colmonoy® 88 exhibit lower volume loss
are shown in Figure 3. The elemental analyses fall with than the D-2 tool steel standard reference material.
the normal ranges for Colmonoy® 88 alloy.
A summary of hardness testing is shown in Figure 5.
COLMONOY® 88 This includes Rockwell C scale test, Vickers hardness
CR W C Fe B Si with 500g load, and Vickers hardness with 25g load for
Deposit
Lots hard phases large enough to support the test.
Type
Spraywelder™
System 92151-4 14.6 15.1 0.7 3.4 3.2 4.2 Hardness
Hard-
(Thermal Spray) Hard- Nominal Vickers 25g
Alloy ness
PTA 116823-0 14.9 15.4 0.7 3.6 3.0 4.1 ness Size of Nominal
Deposit Rock-
Vickers Hard Hardness
Laser 116823-0 14.9 15.4 0.7 3.6 3.0 4.1 Type well C
500g Phases of Phases
Scale
GTAW (TIG) Present
115787 15.7 16.0 0.6 3.7 2.9 4.3
Rod
Spraywelder™
GMAW (MIG) Wire 115-6 14.4 17.3 0.9 3.6 2.8 3.7 System 63 907 <40 μm 900-1375
HVOF 120135-0 15.1 15.3 0.7 3.4 3.0 4.0 (Thermal Spray)

Figure 3. Composition of Colmonoy® 88 lots PTA 64 868 <50 μm 950-1530

Laser 60 925 <20 μm 840-1340
GTAW (TIG) Rod 63 840 <65 μm 810-1360
Results GMAW (MIG)
62 858 <100 μm 1000-1850
The Volume loss for ASTM G65 Procedure A are shown Wire
in Figure 4. The volume loss for the HVOF coating HVOF 58 715 <5 μm n/a
is considerably different from the balance of the
Figure 5. Hardness results
application processes.
The hardness test results shown in Figure 5 are actual
values and not hardness conversions.

WALLCOLMONOY 3
Background Given the differing structures for the fused and welded
Colmonoy 88 powder was developed in the 1980’s
® overlays significant differences in ASTM G65 volume
(Reference US Patent No. 5,141,571). Since its’ losses are not apparent. The expectation is that due to
inception the powder has been made available in the the test conditions and size of the abrasive sand, the
additional particle size distributions suitable for use in test does not reflect results dependent on the size of
the thermal spray and welding processes used for this the hard phases present. The grain size of the sand is
study. Additionally, rod and wire products were also approximately 3 times larger than the size of the hard
developed. Five of the six processes used yielded the phases present. One may expect to see different results
expected results. if the abrasive were smaller than 50 or 25 microns.

It was expected that the microstructure of the The HVOF overlay underwent a significantly different
overlays would correlate to the wear test volume loss. thermal profile during application than did the
Metallographic examination does not lead to a direct others. Much of the microstructural characteristics
correlation. remain similar to those found in the atomized powder
feedstock. Since the degree of melting did not take
Figure 6 shows micrographs of the overlays by process. place in the same time frame as the other processes the
The specimens were etched with Marbles reagent results indicate that the wear resistance of Colmonoy®
to make the various phases/structures more easily 88 relies on precipitation of hard phases formed on
visible. heating near to or above the liquidus temperature of
the alloy.

(a) (b) (c)

(d) (e) (f)

Figure 6. Micrographs of Spraywelder™ System (Thermal Spray) (a), Laser clad (b), PTA Weld (c), GTAW rod weld (d), GMAW wire weld (e),
and HVOF (f)

WALLCOLMONOY 4
Figure 7 shows a typical thermal analysis plot of heat flow versus temperature. This plot indicates phase changes
including solidus/liquidus temperatures as well as phase formation on cooling during solidification.

Figure 7. Thermal analysis trace by Differential Scanning Calorimetry (DSC) for Colmonoy® 88. Heating (bottom) and Cooling (top). Exothermic
reactions peak upward, Endothermic reaction peak downward.

Although the wear test results (excluding HVOF) were not widely divergent we can see that temperature and time
influence microstructure. Thus, it should be noted that sample preparation on small test specimens may not
be representative of the process when the actual parts for service are made (ie. preheat & temperature & time
factors). The specimens prepared for this study were all nominally 25mm wide x 75mm long x 19mm thick.

WALLCOLMONOY 5
Summary
Colmonoy® 88 when fused or welded, exhibits wear properties which are superior to hardened D-2 to steel
under the G65 test conditions. The HVOF coating is nearly equivalent to normalized AISI 1090 steel under these
conditions.

Under the ASTM G65 wear conditions the economics by process can be ranked based on the gas and electric and
feedstock costs. Normalizing to the two-layer PTA weld overlay for a 1m2 surface.

Approximate Cost Normalized to PTA Overlay

Process
to give same wear life (US$/M2)
Spraywelder™ System
620
(Thermal Spray) - Fused

Laser (1 layer) 700

PTA (2 layer) 1170

GTAW (2 layer) 1360

GMAW (2 layer) 1940

HVOF 2690

WALLCOLMONOY 6
References
[1] ASM Metals Handbook Vol. 5, Surface Engineering, published 1994.

[2] American Society of Testing and Materials; Standard Method for Measuring Abrasion Using the Dry Sand/
Rubber Wheel Apparatus; ASTM G65-16.

[3] Evaluation of ASTM G65 Abrasive – Spanning 13 years of Sand; A. Doering, D. Danks, & M. J. Scott; Wear and
Friction Resources, Houston Texas.

WALLCOLMONOY 7
Copyright © 2019 by Wall Colmonoy Corporation. All rights reserved.

No part of this work may be published, translated or reproduced in any form or by

any means, or incorporated into any information retrieval system, without the written
permission of the copyright holder. Permission requests should be addressed to:
Marketing Communications, [email protected]

Disclaimer

Although the information presented in this work is believed to be reliable, this work is
published with the understanding that Wall Colmonoy Corporation and the authors are
supplying general information and are not attempting to render or provide engineering
or professional services. Neither Wall Colmonoy Corporation nor any of its employees
make any warrant, guarantee, or representation, whether expressed or implied, with
respect to the accuracy, completeness or usefulness of any information, product,
process or apparatus discussed in this work; and neither Wall Colmonoy Corporation
nor any of its employees shall be liable for any losses or damages with respect to or
resulting from the user of, or the inability to use, any information, product, process or
apparatus discussed in this work.