SCANIA POWER GENERATION ENGINES

DC09 086A. 267 kW (300 kVA)

US Tier 4f

Standard equipment
• Scania Engine Management System, EMS
• Extra high pressure fuel injection system, XPI
• Variable Geometry Turbocharger
• Fuel filter and extra pre-filter with water
separator
• Fuel heater
• Oil filter, full flow
• Centrifugal oil cleaner
• Oil cooler, integrated in cylinder block
• Oil filler in cylinder block
• Deep front oil sump
• Oil dipstick in cylinder block
• Magnetic drain plug for oil draining
• Starter motor, 1-pole 6.0 kW
• Alternator, 1-pole 100 A
• Flywheel, for use with friction clutch
• Silumin flywheel housing, SAE 1 flange
The power generation engines from Scania are based on a robust design with a • Front-mounted engine suspension
strength-optimized cylinder block containing wet cylinder liners, which can easily be • SCR system
• EGR system
exchanged. Individual cylinder heads with 4 valves per cylinder promotes reparability
• Open crankcase ventilation
and fuel economy.
  The engine is equipped with a Scania-developed Engine Management System, EMS, Optional equipment
• Cooling package
to ensure the control of all aspects related to engine performance.
• Puller and pusher fans
The injection system is Scania’s XPI (Extra High Pressure Injection), a common rail • Cast iron flywheel housing
system that in combination with SCR (Selective Catalytic Reduction) and EGR (Exhaust • Side-mounted PTO
Gas Recirculation) gives low exhaust emissions with good fuel economy and a high • Exhaust connections
• Engine heater
torque. The engine can be fitted with many accessories such as air cleaners, PTOs and
• Stiff rubber engine suspension
cooling package, to suit a variety of installations. It is developed for 60 Hz applica- • Air cleaner
tions. • Closed crankcase ventilation
• Studs in flywheel housing
• Coolant level sensor
• Ramp start delay
• Ramp-up rate
Engine speed (rpm)
1800 rpm (60 Hz)
PRP
Gross power (kW) 267
Gross power (kWe) 239
Gross power (kVA) 300
Gross torque (Nm) 1416
Fuel consumption at full load (g/kWh) 205
Fuel consumption at 3/4 load (g/kWh) 208
Fuel consumption at 1/2 load (g/kWh) 219
Reductant consumption at full load (g/kWh) 13
Heat rejection to coolant (kW) 141

PRP – Prime Power: For continuous operation at varying load. Max. mean load factor of 70% of
rated power over 24 h of operation. 1 hour/12 hour period above 100% load. Max. 25 h accumulated This specification may be revised without notice.
service time above 100% load per year.
 SCANIA POWER GENERATION ENGINES

DC09 086A. 267 kW (300 kVA)

US Tier 4f

Engine description

No of cylinders 5 in-line
Working principle 4-stroke
Firing order 1-2-4-5-3
Displacement 9.3 litres
Bore x stroke 130 x 140 mm
Compression ratio 17:1
Weight 975 kg (excl oil and coolant)
Piston speed at 1500 rpm 7.0 m/s
Piston speed at 1800 rpm 8.4 m/s
Camshaft High position alloy steel
Pistons Aluminium pistons
Connection rods I-section press forgings of alloy steel
Crankshaft Alloy steel with hardened
and polished bearing surfaces
Oil capacity 31-36 dm3
Electrical system 1-pole 24 V DC
1:7243

1234
Edition 03 © Scania CV AB, SE-151 87 Södertälje, Sweden

510 472
684
423

1:7244

All dimensions in mm

SE 151 87 Södertälje, Sweden

Telephone +46 8 553 810 00
www.scania.com
[email protected]
 SCANIA POWER GENERATION ENGINES

SCR system
US Tier 4f

Reductant SCR (Selective Catalytic Reduction) technology is used on Scania’s engines for
US Tier 4f to reduce NOX content in the exhaust gases. A chemical process is
started when reductant, a urea and water mixture, is injected into the exhaust
gas stream. During the injection, the water evaporates, and the urea breaks
down to form ammonia. The ammonia then reacts with the nitrogen gases
Exhaust in the SCR catalytic converter and forms harmless products such as nitrogen
Catalytic gas gas and water. Through the use of SCR, the exhaust gases are purged of
converter poisonous levels of NOX in a highly efficient way. Scania makes use of a
Engine system that is carefully developed and tested in our own laboratory.

The reductant tank is available in different sizes. It is heated by the engine

NH3+NOx N2+H2O cooling system to avoid freezing of the urea solution; urea freezes at -11°C.
The reductant tank and a pump are delivered as a unit, which is fitted with
brackets for easy installation. The Scania system contains all necessary
mechanical and electrical parts, except exhaust piping, which should be
Working principle for Scania’s SCR system adapted to the customer´s installation.

Mechanical system Electrical system

5 3
1 2

3
4
6 2 4

12
1

7 6

11 10
9

8 5
7

Standard Optional Standard Optional

1 Evaporator  - 1 Electrical cable between engine and
3m 4.5 m, 6 m
4 m, 5 m, 6.5 m SCR control unit
2 Reductant pressure hose 2.5 m
2 NOx sensor electrical cable 3m 4.5 m, 6 m
Coolant hose for heating of
3 - -
reductant tank and pump 3 Electrical interface to SCR system  -
4 Coolant valve  - 4 Reductant doser electrical cable 3m 4.5 m, 6 m
5 Reductant return hose 2.5 m 4 m, 5 m, 6.5 m 5 Temperature sensor electrical cable 3m 4.5 m, 6 m, 9 m
6 Reductant tank 38 l 45 l, 60 l, 63 l, 70 l 6 Temperature sensor electrical cable 3m 4.5 m, 6 m, 9 m
Coolant hose, return from heating 7 NOx sensor electrical cable 3m 4.5 m, 6 m, 9 m
7 - -
of tank and pump
8 NOx sensor with control unit  -
9 Oxidation catalytic converter* Engine-mounted Separate
10 Exhaust temperature sensor  -
11 SCR catalytic converter  -
12 NOx sensor with control unit  -
*Not DC13 085A or DC16.

This specification may be revised without notice.

 SCANIA POWER GENERATION ENGINES

SCR system
US Tier 4f

Reductant tank 38 litres Evaporator (DC09 and DC13)

Total volume: 50 litres
Filling volume: 38 litres

720 280

671

03:5912

Evaporator (DC16)

Other available sizes: 45 litres (total volume 60 litres)

60 litres (total volume 75 litres
63 litres (total volume 80 litres)
70 litres (total volume 90 litres)

SCR catalytic converter Oxidation catalytic converter (not DC13 085A or DC16)

A
Ø348.5

1:7357

Engine Dimensions A (mm)

Edition 11 © Scania CV AB, SE-151 87 Södertälje, Sweden

DC09 (202 kW-257 kW) 786

DC09 (276 kW-294 kW) 900
DC13 (257 kW-331 kW) 900
DC13 (368 kW-405 kW) 970
DC16 970

SE 151 87 Södertälje, Sweden

Telephone +46 8 553 810 00
This specification may be revised without notice. www.scania.com
[email protected]