April 2004

Page 1
INSTRUCTION MANUAL FOR
CHIRALPAK® IA COLUMNS
Please read this instruction sheet completely before using this column

Column description

Packing composition: Amylose tris (3,5-dimethylphenylcarbamate)

immobilized on 5µm silica-gel.

O CH3
OR R= C
O
N
RO
H
CH3
OR
O n

silica-gel

Shipping solvent: n-Hexane / ethanol solvent mixture (90/10 v/v)

All columns have been pre-tested before packaging. Test parameters and results, as well as the Column
Lot Number, are included on a separate (enclosed) page.

THIS INSTRUCTION SHEET IS NOT APPLICABLE TO ANY OTHER DAICEL COLUMNS

Operating restrictions

150 x 2.0 mm ID 150 x 4.6 mm ID

250 x 10 mm ID 250 x 20 mm ID
250 x 2.0 mm ID 250 x 4.6 mm ID
Semi-prep. columns Semi-prep. columns
Analytical columns Analytical columns

Flow rate direction As indicated on the column label

~ 0.1 - 0.2 ml/min ~ 1 ml/min ~ 5 ml/min ~ 18 ml/min

Typical Flow rate • Do not exceed Do not exceed Do not exceed Do not exceed
0.3 ml/min 1.5 ml/min 7 ml/min 25 ml/min
Should be maintained < 50 Bar (~700 psi)ƒ for maximum column life
Pressure limitation ‚
Adapt flow rates to the size of the column. Do not exceed 100 Bar (~1400 psi)
Temperature 0 to 40°C

• The maximum flow rate depends on the mobile phase viscosity (mobile phase composition), and should be
adjusted in accordance with the pressure upper’s limit (i.e. 100 Bar).

Examples Column 250 x 4.6mm ID Column 250 x 20mm ID

Alkane/organic modifier~ 90:10 0.5 to 1.5 ml/min 18 to 25 ml/min

100% EtOH ~ 0.5 ml/min ~ 5 to 8 ml/min

100% 2-propanol ~ 0.2-0.3 ml/min ~ 3 to 5 ml/min

‚ The back pressure value that should be taken into account is the one generated by the column itself.
This value is measured by calculating the difference between the pressure of [LC system + column] and
the pressure of the LC system free of the column.

ƒ Ideal value for maximum column life, but stable up to 100 Bar.

q The use of a guard cartridge is highly recommended for maximum column life.

q Samples should be filtered through a membrane filter of approximately 0.5µm porosity.

CHIRAL TECHNOLOGIES EUROPE ● Bd Gonthier d’Andernach ● BP 80140 ● 67404 Illkirch – Cedex ● FRANCE
Tel.:+ 33 (0) 3 88 79 52 00 ● Fax: + 33 (0) 3 88 66 71 66 ● email: [email protected] ● web site: http:// www.chiral.fr
April 2004
Page 2

Operating procedure

A - Mobile phases

CHIRALPAK® IA allows free choice of any miscible solvents to compose the mobile phase. The column can be used
with all ranges of organic miscible solvents, progressing from the traditional mobile phases used with other Daicel
columns (mixtures of alkanes/alcohol, pure alcohol or acetonitrile) to mobile phases containing ethyl acetate,
tetrahydrofurane (THF), methyl tert-butyl ether (MtBE), dichloromethane (CH2Cl2) and chloroform(CHCl3), among
others.

Two groups of solvents can be identified with regards to CHIRALPAK® IA:

• Group A: standard solvents commonly used for coated-type polysaccharide-derived columns.
• Group B: extended solvent range.

In the following tables some guidelines will be given in order to assist the user in the method development. In
Table 1 several solvent mixtures of both groups are described, together with the typical starting conditions and
advised optimisation ranges. Solvents are arranged according to their eluting strength. Toluene, MtBE and
chlorinated solvents can be used in their pure form in the mobile phase. For fast eluting solvents, such as THF,
1,4-dioxane or acetone, we recommend to be used in combination with solvents of group A (especially alkanes) in
order to modulate the retention. In Table 2 the solvent mixtures of group A are shown following the same criteria
as in Table 1. Extreme pH ranges must be avoided because they can damage the silica gel used in this column.

Table 1. Typical mobile phases containing solvents of group A and B

MtBEΠCHCl3ΠCH2Cl 2ΠEthyl acetate THF 1,4-Dioxane Acetone

Group B solvents
Group A solvents Ethanol• AlkaneŽ AlkaneŽ AlkaneŽ AlkaneŽ AlkaneŽ AlkaneŽ

Typical starting
conditions 98:2 60:40 50:50 40:60 30:70 25:75 25:75
(solvent B/solvent A)
80:20 25:75 25:75 20:80 10:90 10:90 10:90
Advised optimisation
to to to to to to to
range
100:0 100:0 100:0 70:30 50:50 40:60 40:60
ΠSome solvents such as MtBE, CHCl3 or CH2Cl2 may need the combination with alcohols (usually 1-5%) to modulate retention times and improve
peak shape.
• Organic modifiers in MtBE can also be: 2-propanol, methanol, THF, ethyl acetate, methyl acetate, 1,4-dioxane or acetone.
Ž Alkane: n-hexane, iso-hexane or n-heptane. Some small selectivity differences may sometimes be found.

Table 2. Typical mobile phases containing solvents of group A

Group A solvent AlkaneŽ/ AlkaneŽ/

Ethanol• Methanol• Acetonitrile alkaneŽ/ EtOH•
mixtures 2-PrOH• MeOH•

Typical starting
100 100 100 90:10 90:10 95:5
conditions

99:1 99:1 99:1

100-50% in 100-50% in 100-80% in
Advised
MeOH, 2-PrOH EtOH, 2-PrOH MeOH, EtOH to to to
optimisation range
or ACN or ACN or 2-PrOH
50:50 50:50 50:25:25‘
• Certain alcohol mixtures have a higher viscosity. Pressure should be controlled and flow rate reduced if necessary.
• The retention is generally shorter with a higher alcohol content. The use of other alcohols such as 1-propanol, 1-BuOH, 2-BuOH etc…is possible.
‘ No range limitation, but due to miscibility restrictions, mix methanol with an equal volume of ethanol when using with alkane mixtures,
otherwise, separation of liquid phases might happen. A maximum of 5% methanol in n-hexane may be used without adding ethanol.

Based on our extensive experience the above mentioned solvents and their mixtures can be classified in two
groups in terms of enantioselectivity. However, the separation ability of the chiral support may be different
depending on the sample.

Alcohols, THF, MtBE, CH2Cl2 > Ethyl acetate, acetonitrile, CHCl3, toluene, 1,4-dioxane, acetone

CHIRAL TECHNOLOGIES EUROPE ● Bd Gonthier d’Andernach ● BP 80140 ● 67404 Illkirch – Cedex ● FRANCE
Tel.:+ 33 (0) 3 88 79 52 00 ● Fax: + 33 (0) 3 88 66 71 66 ● email: [email protected] ● web site: http:// www.chiral.fr
April 2004
Page 3

We would recommend THF, MtBE, dichloromethane or alcohols (pure or in alkane mixtures) to begin the
development of an analytical method’. The solvent leading to a higher solubility of your sample will be the first
choice when this is a limiting factor.

’ Detection with a regular UV detector may become difficult depending on a combination of sample and mobile phase (e.g. acetone, ethyl acetate,
toluene, high percentages of chloroform). In those cases an alternative detector, such as RI detector or ELSD (Evaporative Light Scattering
Detector), may be more effective than the UV.

B – Additives Basic Samples Acidic Samples

require require
For basic or acidic samples, it is
Basic additives Acidic additives
necessary to incorporate an additive
DEA TFA
into the mobile phase in order to Butyl amine“ CH3COOH
optimize the chiral separation: Ethanol amine” HCOOH

“ For primary amines mainly < 0.5% < 0.5%

” For primary amino alcohols mainly Typically 0.1% Typically 0.1%

ð STRONGLY BASIC solvent additives or sample solutions MUST BE AVOIDED, because they are likely to damage the silica gel
used in this column.

Column care / Maintenance

F Column cleaning and regeneration procedures

Chiral recognition of polysaccharide type phases also depends on the supramolecular structure of the
polymeric chiral selector. The molecular conformation can change in different solvating environments. In order
to ensure consistent performances after extensive use with different mobile phases, a regeneration method
may be necessary to eliminate any unexpected change of chiral recognition due to the history of the column
(mobile phases, additives,…).

• Flush with ethanol (0.5 ml/min for 30 min) followed by 100% THF at 0.5 ml/min for 2 hours.
• Flush with ethanol (0.5 ml/min for 30 min) and then equilibrate with alkane / ethanol = 80 / 20 (v/v)
prior to retesting the column.

If this is not successful, then try with 100% N,N-dimethylformamide or N,N-dimethylacetamide at 0.3 ml/min
for 3 hours instead of the THF flush.

Column storage
q Ethanol can be used as universal storage solvents. However, if you are working with alkane containing mobile
phases, the column can be kept in n-hexane / ethanol 90/10 when stored for more than one week.

q For columns used with acidic or basic additives, flush the column with the same mobile phase without the
modifier before storage.

Operating this column in accordance with the guidelines outlined here will result in a long column life.

Solvent effects on CHIRALPAK®IA separations

methaqualone ð Separation examples for racemic methaqualone on CHIRALPAK® IA

O (25 x 0.46 cm, 25°C)
CHIRALPAK® IA
N
n-hexane/CH2Cl2 75:25 Mobile phase k’1 α Rs
CH α= 2.36
N CH3 3 n-hexane/2-propanol 80:20 1.45 1.65 7.08
Rs = 25.1
n-hexane/methyl acetate 80:20 1.87 1.70 9.45
n-hexane/chloroform 50:50 0.64 1.79 7.84
n-hexane/dichloromethane 75:25 2.90 2.36 25.1
n-hexane/acetone 85:15 1.42 1.33 5.82
n-hexane/tetrahydrofuran 85:15 3.14 1.63 11.3
methyl tert-butyl ether/ethanol 95:5 0.73 2.81 13.1
0 10 20 min
toluene/n-hexane/ethanol 70:25:5 0.54 1.96 9.28

CHIRAL TECHNOLOGIES EUROPE ● Bd Gonthier d’Andernach ● BP 80140 ● 67404 Illkirch – Cedex ● FRANCE
Tel.:+ 33 (0) 3 88 79 52 00 ● Fax: + 33 (0) 3 88 66 71 66 ● email: [email protected] ● web site: http:// www.chiral.fr
April 2004
Page 4

H O
Hexobarbital N

O N OH OH
N
Cl
N 0.8 Cl

O Lorazepam
40

0.6

30

0.4
100% methyl tert-
tert-butyl ether n-hexane/acetone
hexane/acetone
20 60:40
k1’ = 0.31
k1’ = 1.75
α= 2.94
0.2 α= 1.47
Rs = 7.46
a

10
Rs = 7.97
Detection:: UV 230 nm
Detection
Detection:: ELSD
Detection
0.0
0
0 1 2 3 4 5 6 7 8 9 0 2 4 6 8 10 12 14 16 18
Minutes Minutes

Bupivacaine O

0.8 0.20
O Cl
N HO
N N
0.7 N
H

0.15
0.6 Hydroxyzine

0.5
n-hexane/THF/DEA n-hexane/
hexane/ethyl
ethyl acetate
acetate/DEA
/DEA
0.4 0.10
90:10:0.1 40:60:0.1
0.3 k1’ = 3.94 k1’ = 2.90
α= 1.55 α= 2.22
0.2 0.05
Rs = 8.20 Rs = 19.64
0.1 Detection:: ELSD
Detection Detection:
Detection: ELSD

0.0 0.00

0 5 10 15 20 25 30 35 0 4 8 12 16 20 24 28
Minutes Minutes

1.0 O

300 Naproxen O
S
OH
HO
O 0.8
250 O
Suprofen

200 0.6

150 n-hexane/ethyl
hexane/ethyl acetate/TFA
acetate/TFA
n-hexane/CH2Cl2 /2
/2-
-PrOH
PrOH/TFA
/TFA
0.4 70:30:0.1
35:65:1:0.1
100 k 1’ = 2.83
k1’ = 2.89
α= 1.18
α= 1.18 0.2
50 Rs = 3.65
Rs = 2.59
Detection:
Detection: UV 254 nm
Detection:: UV 254 nm
Detection
0 0.0

0 2 4 6 8 10 12 14 16 18 20 0 2 4 6 8 10 12 14 16 18 20
Minutes Minutes

General conditions: CHIRALPAK® IA 25 x 0.46 cm, Flow rate: 1 ml/min, 25°C

ð If you have any questions about the use of this column, or encounter a problem, please contact
CHIRAL TECHNOLOGIES EUROPE for assistance ([email protected]).

For more detailed information about this column and other Daicel supports, refer to our catalogue also available on
our website: http://www.chiral.fr or contact CHIRAL TECHNOLOGIES EUROPE.

CHIRALCEL®, CHIRALPAK® and CROWNPAK® are registered trademarks of

DAICEL CHEMICAL INDUSTRIES LTD

CHIRAL TECHNOLOGIES EUROPE ● Bd Gonthier d’Andernach ● BP 80140 ● 67404 Illkirch – Cedex ● FRANCE
Tel.:+ 33 (0) 3 88 79 52 00 ● Fax: + 33 (0) 3 88 66 71 66 ● email: [email protected] ● web site: http:// www.chiral.fr