Dl650 Op Guide

www.imagistics.
com
DL650
Operating Manual
For use with Imagistics and Pitney Bowes DL650 copier/printers.
Recycled paper is used for the inside pages of this book.
DL650
Operating Manual
ENERGY STAR® Program

The ENERGY STAR Program has been established to encourage the
widespread and voluntary use of energy-efficient technologies that reduce
energy consumption and prevent pollution. As an ENERGY STAR Partner,
Imagistics International Inc. has determined that this product meets the
ENERGY STAR guidelines for energy efficiency, based on the following
features.
Auto Low Power

This function conserves energy by lowering the set temperature of the fixing unit. In the standard setting, Auto
Low Power operates automatically when 15 minutes have elapsed after completion of the last copy, with the
copier remaining in the ready to copy state during that time.
The time period for the Auto Low Power function can be set for 5 minutes, 10 minutes, 15 minutes, 30 minutes, 60
minutes, 90 minutes, 120 minutes, or 240 minutes. See p. 5-2 for details.
Automatic Shut-Off
This function achieves further energy conservation by partially turning the power supply OFF, thereby reducing
energy consumption to 20W or less. In the standard setting, Automatic Shut-Off follows Auto Low Power,
operating automatically when 90 minutes have elapsed after completion of the last copy, with the copier
remaining in the ready to copy state during that time.
The time period for the Automatic Shut-Off function can be set for 30 minutes, 60 minutes, 90 minutes, 120
minutes or 240 minutes. See p. 5-4 for details.
Automatic Duplex Copying

To reduce paper consumption, use this function to make double-sided (duplex) copies, automatically.
We recommend that you utilize the Auto Low Power function, the Automatic Shut-Off function, and the Automatic
Duplex Copying function.
Supplies
The supplies listed below have all been designed especially for Imagistics and Pitney Bowes copiers to ensure maximum
product performance and quality. Substituting other supplies may result in interior copy quality and machine
malfunction. Ordering supplies is quick and easy.
To order Supplies: Call the Imagistics Supply Line at 1-800-462-6797
To speak to a technical support representative: Call the Imagistics National Diagnostic Center
at 1-800-243-5556
Description/Order Name How much to Description

keep on hand
Printpowder® Toner 1 Carton Contains 8 toner cartridges

475-0
Copier Paper (8 1/2” x 11”) 10 Cartons Contains 5,000 sheets

471-1 per carton (10 reams)
Copier Paper (8 1/2” x 14”) 2 Cartons Contains 3,000 sheets

Copier Paper (11” x 17”) 2 Cartons Contains 2,500 sheets

3-Hole Punched 2 Cartons Contains 5,000 sheets

Copy Paper (8 1/2” x 11”) per carton (10 reams)
471-9
Transparencies 1 Box Contains 100 sheets

257-9 per carton
Developer* 1 Carton Contains 1 bag per carton

475-4
Staples for 9922 & 9940 1 Carton Contains (3) 5,000 staple
Finishers: 847-3 cartridges
Staples for 9922 Finisher: 1 Carton Contains (3) 5,000 staple

472-3 cartridges
*Note: This item can only be installed by an Imagistics customer Service

Representative and should be kept on hand for preventative maintenance.
Model: DL650
Serial Number:
Contents
Section 1: Introduction
To the User..................................................................................................................... 1-2
Key Operator Functions .......................................................................................... 1-2
Copier Service, Repairs & Supplies........................................................................ 1-2
Machine Labels....................................................................................................... 1-2
Control Panel with Interactive Touch Screen........................................................... 1-2
Overview of the Operating Manual.......................................................................... 1-3
Help Mode............................................................................................................... 1-3
Product Overview........................................................................................................... 1-4
Features of the DL650 ................................................................................................... 1-5
Copier Features ........................................................................................................... 1-11
Standard Equipment ............................................................................................. 1-11
Optional Equipment .............................................................................................. 1-11
Section 2: Safety Information

User Instructions ............................................................................................................ 2-2
Machine Labels .............................................................................................................. 2-3
Label Locations....................................................................................................... 2-3
Machine Installation and Power Requirements .............................................................. 2-6
Machine Handling and Care........................................................................................... 2-8
Routine Safety................................................................................................................ 2-9
Finisher Capacity Requirements .................................................................................. 2-10
Regulations .................................................................................................................. 2-12
FCC Regulations................................................................................................... 2-12
ICES Regulations.................................................................................................. 2-12
Laser Safety .......................................................................................................... 2-12
Internal Laser Radiation........................................................................................ 2-13
Laser Safety Label ................................................................................................ 2-16
Ozone Release ..................................................................................................... 2-17
Section 3: Machine Information

Machine Configuration ................................................................................................... 3-2
External Machine Call-outs ..................................................................................... 3-3
Internal Machine Call-outs ...................................................................................... 3-4
Optional Equipment ................................................................................................ 3-5
Site Requirements........................................................................................................ 3-10
Control Panel Layout.................................................................................................... 3-12
Touch Screen ............................................................................................................... 3-13
Basic Screen......................................................................................................... 3-13
Initial Settings............................................................................................................... 3-14
Panel Reset Mode........................................................................................................ 3-14
Automatic Paper Selection (APS) ................................................................................ 3-14
Contents
Section 3: Machine Information (continued)

Automatic Magnification Selection (AMS) .................................................................... 3-14
Automatic Exposure Selection (AES)........................................................................... 3-14
Automatic Tray Switching (ATS) ................................................................................... 3-14
Lead Edge Delete ........................................................................................................ 3-15
Service Settings ........................................................................................................... 3-15
Finisher-Paper Capacity........................................................................................ 3-15
Key Operator Password ........................................................................................ 3-15
ECM Master Key Code ......................................................................................... 3-15
Weekly Timer Master Key Code............................................................................ 3-15
HDD Management Password................................................................................ 3-16
Staple Sheet Capacity .......................................................................................... 3-16
Section 4: Paper Information

Positioning Originals on the Platen Glass ...................................................................... 4-2
Positioning an Original for Manual Copying ............................................................ 4-2
Using the Electronic Document Handler (EDH) ............................................................. 4-3
Positioning Originals ............................................................................................... 4-4
Positioning Mixed Originals..................................................................................... 4-5
Paper in Main Body Trays............................................................................................... 4-6
Paper in 9930 Large Capacity Cassette (Option) .......................................................... 4-7
Paper in 9932 Large Capacity Cassette (Option) .......................................................... 4-7
Paper in Automatic Duplex Unit ..................................................................................... 4-8
Paper in Multi-Sheet Bypass Tray .................................................................................. 4-8
Paper in 9940/9922 Finisher (Option) ............................................................................ 4-9
9940/9922 Finisher Primary (Main) Tray ................................................................. 4-9
9940/9922 Finisher Secondary (Sub) Tray............................................................ 4-10
9922 Finisher Booklet Tray.................................................................................... 4-10
Paper in 9924 Cover Inserter (Option) ......................................................................... 4-11
Paper in Punch Kit (Option) ......................................................................................... 4-12
Paper Weight Compatibility Chart ................................................................................ 4-12
Contents
Section 5: Copier Management

Energy Saver Mode ....................................................................................................... 5-2
Auto Low Power ...................................................................................................... 5-2
Manual Low Power.................................................................................................. 5-3
Auto Shut-Off .......................................................................................................... 5-4
Manual Shut-Off...................................................................................................... 5-4
Entering an ECM Password ........................................................................................... 5-5
Weekly Timer Function................................................................................................... 5-6
Timer Interrupt ........................................................................................................ 5-6
Counter List.................................................................................................................... 5-8
To Display the Counter List ..................................................................................... 5-8
To Print the Counter List ......................................................................................... 5-8
Machine Condition Information ...................................................................................... 5-9
Section 6: Basic Operations

How to Make a Basic Copy ............................................................................................ 6-2
The Basic Screen.................................................................................................... 6-2
Setting Job During Warm-up................................................................................... 6-4
To Stop Scanning/Printing....................................................................................... 6-5
Recalling Previous Job Settings.............................................................................. 6-6
Copy Mode..................................................................................................................... 6-7
Copy Mode Using EDH ........................................................................................... 6-8
1s2 Copy Mode Using Platen Glass...................................................................... 6-9
Using the Multi-Sheet Bypass Tray .............................................................................. 6-11
Copy Density................................................................................................................ 6-13
Automatic Exposure Selection (AES).................................................................... 6-13
Manual Mode (Lighter, Normal, Darker)................................................................ 6-13
Density Shift.......................................................................................................... 6-14
Lens Mode ................................................................................................................... 6-16
Automatic Paper Selection (APS) ......................................................................... 6-16
Automatic Magnification Selection (AMS) ............................................................. 6-17
Selecting a Special Ratio for Non-Standard Paper ............................................... 6-18
Special Ratio Table ............................................................................................... 6-19
Preset and Custom Zoom Ratios.......................................................................... 6-20
Zoom Mode........................................................................................................... 6-21
Vertical/Horizontal Zoom....................................................................................... 6-22
Copy Size ..................................................................................................................... 6-23
Selecting Paper Type/Size for Multi-Sheet Bypass Tray ........................................ 6-24
Binding Mode ............................................................................................................... 6-27
Contents
Section 6: Basic Operations (continued)

Reserve........................................................................................................................ 6-28
Set Reserve Job ................................................................................................... 6-28
Job Status Screen................................................................................................. 6-30
Mishandled Paper During the Reserve Setting ..................................................... 6-33
When Paper is Depleted for the Job in Progress .................................................. 6-34
Store Mode................................................................................................................... 6-35
Platen Store Mode ................................................................................................ 6-35
EDH Store Mode................................................................................................... 6-37
Interrupt Mode.............................................................................................................. 6-38
Rotation........................................................................................................................ 6-40
Rotation and APS ................................................................................................. 6-40
Rotation and AMS................................................................................................. 6-41
To Release Automatic Rotation............................................................................. 6-42
Check Mode and Proof Copy ....................................................................................... 6-43
Help Mode.................................................................................................................... 6-46
Section 7: Output Modes

9940/9922 Finisher Specifications ................................................................................. 7-2
Non-Sort Mode Using Primary (Main) Tray .................................................................... 7-5
Sort Mode Using Primary (Main) Tray ............................................................................ 7-6
Staple-Sort Mode Using Primary (Main) Tray................................................................. 7-7
Group Mode Using Primary (Main) Tray....................................................................... 7-10
Output Modes Using Secondary (Sub) Tray................................................................. 7-11
Folding and Stapling & Folding Modes......................................................................... 7-13
Punching Mode ............................................................................................................ 7-16
Three-Folding Mode..................................................................................................... 7-18
9924 Cover Inserter ..................................................................................................... 7-20
Manual Finishing .......................................................................................................... 7-23
Output Mode for Machine without Finisher .................................................................. 7-26
Face Down Exit ..................................................................................................... 7-27
Face Up Exit.......................................................................................................... 7-30
Section 8: Special Original

Special Original Screen ................................................................................................. 8-2
Original Direction ........................................................................................................... 8-3
Text/Photo Enhance ....................................................................................................... 8-4
Special Original .............................................................................................................. 8-6
Mixed Original ......................................................................................................... 8-6
Z-Folded Original .................................................................................................... 8-8
Original Form ................................................................................................................. 8-9
Contents
Section 9: Applications
Application Function Menu............................................................................................. 9-2
Sheet/Cover Insertion .................................................................................................... 9-3
Chapter .......................................................................................................................... 9-8
Combination ................................................................................................................. 9-10
Booklet ......................................................................................................................... 9-12
Transparency Interleave ............................................................................................... 9-15
Image Insert ................................................................................................................. 9-17
Book Copy.................................................................................................................... 9-19
Program Job................................................................................................................. 9-21
Non-Image Area Erase ................................................................................................ 9-23
Reverse Image ............................................................................................................. 9-25
Repeat Image............................................................................................................... 9-26
Frame/Fold Erasure ..................................................................................................... 9-29
AUTO Layout................................................................................................................ 9-31
All-Image Area ............................................................................................................. 9-33
Image Shift ................................................................................................................... 9-34
To Adjust Position of Copy Image ......................................................................... 9-34
To Reduce and Shift Copy Image ......................................................................... 9-37
Stamp........................................................................................................................... 9-39
Overlay ......................................................................................................................... 9-44
Overlay Memory........................................................................................................... 9-46
To Store Overlaying Image Data in HDD .............................................................. 9-46
To Overlay Image Stored in HDD.......................................................................... 9-49
Section 10: Program Memory

Job Store...................................................................................................................... 10-2
Job Recall .................................................................................................................... 10-4
Program Memory Form ................................................................................................ 10-6
Contents
Section 11: Server Function

Server Function............................................................................................................ 11-2
Image Store/Delete Mode ............................................................................................ 11-4
To Store Image Data in HDD ................................................................................ 11-4
To Delete Image Data ........................................................................................... 11-7
Image Store & Output Mode ........................................................................................ 11-8
Image Recall Mode .................................................................................................... 11-10
Section 12: Shortcuts

Set Reserve Job........................................................................................................... 12-2
Store Originals Scanned from Platen........................................................................... 12-2
Store Originals Scanned from EDH ............................................................................. 12-2
Stapling & Folding, and Folding ................................................................................... 12-3
Mixed Original .............................................................................................................. 12-3
Sheet/Cover Insertion .................................................................................................. 12-3
Chapter ........................................................................................................................ 12-4
Combination ................................................................................................................. 12-4
Booklet ......................................................................................................................... 12-4
Transparency Interleave ............................................................................................... 12-5
Image Insert ................................................................................................................. 12-5
Book Copy.................................................................................................................... 12-6
Program Job................................................................................................................. 12-6
Non-Image Area Erase ................................................................................................ 12-6
Reverse Image ............................................................................................................. 12-7
Repeat Image............................................................................................................... 12-7
Frame/Fold Erasure ..................................................................................................... 12-7
AUTO Layout................................................................................................................ 12-8
All-Image Area ............................................................................................................. 12-8
Image Shift/ Reduce & Shift ......................................................................................... 12-8
Stamp/Overlay ............................................................................................................. 12-9
Loading Paper ............................................................................................................ 12-10
Adding Toner .............................................................................................................. 12-10
Contents
Section 13: Key Operator Mode

To the Key Operator ..................................................................................................... 13-2
How to Access the Key Operator Mode ................................................................ 13-3
Function Menu Map ..................................................................................................... 13-4
System Initial Setting [1]............................................................................................... 13-7
Date & Time Setting [1] ......................................................................................... 13-7
Language Select Setting [2].................................................................................. 13-9
IP Address Setting [3] ......................................................................................... 13-10
E-Mail Transmission Setting [4]........................................................................... 13-11
Copier Initial Setting [2] .............................................................................................. 13-13
User Setting Mode [3] ................................................................................................ 13-15
User Density Level 1 Setting [1].......................................................................... 13-15
User Density Level 2 Setting [2].......................................................................... 13-16
User Lens Mode Ratio Setting [3] ....................................................................... 13-17
ECM (Electronic Copy Monitor) Function Setting [4].................................................. 13-18
How to Access the ECM Setting Mode ............................................................... 13-19
E.C.M. Data Edit [1]............................................................................................. 13-20
E.C.M. All Count Reset [2] .................................................................................. 13-24
E.C.M. Function Setting [3] ................................................................................. 13-25
Lock / Delete Program Memory [5] ............................................................................ 13-26
Paper Type / Special Size Set [6] ............................................................................... 13-27
Panel Contrast / Key Sound Adjustment [7] ............................................................... 13-29
Key Operator Data Setting [8] .................................................................................... 13-30
Weekly Timer [9] ........................................................................................................ 13-31
How to Access the Weekly Timer Setting Mode ................................................. 13-32
Weekly Timer On/Off Setting [1] ......................................................................... 13-33
Timer Setting [2].................................................................................................. 13-34
Timer Action On/Off Setting [3] ........................................................................... 13-36
Lunch Hour Off Setting [4] .................................................................................. 13-38
Timer Interrupt Password Setting [5]................................................................... 13-39
Control Panel Adjustment [10] ................................................................................... 13-40
Tray Auto Select Setting [11] ...................................................................................... 13-41
Energy Saver Setting [12] .......................................................................................... 13-42
Memory Switch Setting [13] ....................................................................................... 13-43
Machine Management List Print [14] ......................................................................... 13-50
Call Remote Center [15]............................................................................................. 13-51
Side 2 Lens Adjustment [16] ...................................................................................... 13-52
Finisher Adjustment [17] ............................................................................................ 13-53
HDD Management Setting [18] .................................................................................. 13-55
Non-Image Area Erase Setting [20] ........................................................................... 13-57
Key Operator ECM Form............................................................................................ 13-58
Contents
Section 14: Maintenance & Supplies

Loading Paper .............................................................................................................. 14-2
Paper Indicator...................................................................................................... 14-2
Paper Empty Indicator........................................................................................... 14-2
Using the HELP Key ............................................................................................. 14-2
Loading Paper in Tray 1, 2, and 3 ......................................................................... 14-3
Loading Paper in LCC (9930/9932) ...................................................................... 14-4
Loading Tabbed Sheets in Tray 1, 2, or 3 .............................................................. 14-5
Loading Tabbed Sheets in LCC (9930/9932) ........................................................ 14-6
Adding Toner ................................................................................................................ 14-7
Inserting a New Staple Cartridge into 9940/9922 Finisher .......................................... 14-8
Empty Trash Basket of Punch Kit ................................................................................. 14-9
Preventive Maintenance............................................................................................. 14-10
Reading the PM Counter .................................................................................... 14-10
Printing the PM Counter...................................................................................... 14-10
Cleaning the Left Partition Glass................................................................................ 14-11
Cleaning the Document Glass and Cover .................................................................. 14-11
Section 15: Troubleshooting

Call for Service............................................................................................................. 15-2
Limited Use of the Copier in Trouble ..................................................................... 15-3
Memory Overflow ......................................................................................................... 15-4
Power OFF/ON Screen ................................................................................................ 15-5
Clearing Mishandled Paper.......................................................................................... 15-6
Copying Hints............................................................................................................... 15-8
Section 16: Machine Specifications

Specifications ............................................................................................................... 16-2
DL650us01v1.fm 1 ページ２００１年１１月１４日　水曜日　午後２時５１分
Section 1: Introduction
To the User
Key Operator Functions
Copier Service, Repairs & Supplies
Machine Labels
Control Panel with Interactive Touch Screen
Overview of the Operating Manual
Help Mode
Product Overview
Features of the DL650
Copier Features
Standard Equipment
Optional Equipment
Introduction 1-1
Introduction
To the User
Welcome to the DL650. The following topics relate to general product information and
provide tips on using this manual.
Key Operator Functions

Custom settings can be made by the key operator or anyone who is responsible for the
machine. Access to the Key Operator mode may require a Key Operator password, if
previously set by your service representative. Use the password system to limit use of Key
Operator functions to a person who is authorized to handle the responsibility.
Copier Service, Repairs & Supplies

Copier service and repairs should be performed only by an authorized service
representative. To maintain personal safety and to avoid machine damage, never
disassemble the machine for any reason. To ensure optimal copy quality, use only supplies
that are recommended by us.
Machine Labels
Information labels are affixed to the copier to provide quick and easy instructions on basic
copying, loading paper, adding toner, and clearing mishandled paper. In addition, safety
labels are attached to various internal areas of the copier, to provide cautionary
information that must be heeded to prevent personal injury or damage to the copier.
Sample machine safety labels are shown in Section 2: Safety Information.
Control Panel with Interactive Touch Screen

The DL650 control panel is user friendly and easy to operate. The far right portion of the
panel displays the Copy/Scan/Print indicator and keys to select the mode as well as the
Timer indicator and buttons to select Energy Saver, Interrupt and Panel Reset modes.
Adjacent to this section is the keypad to select Print Quantity, Clear Quantity and Stop. The
next section on the left displays the keys to select Help, Program Memory, Mode Check,
Utility and Proof Copy modes. To the left is the LCD screen.
Copying modes, selections, and setting changes can be made from the touch screen. The
upper portion of the touch panel automatically displays machine status information, as
required. In addition, the [Help] key will display information on each function that is
displayed on the screen and will provide step-by-step instructions.
1-2 Introduction
Introduction
To the User (continued)
Overview of the Operating Manual
For optimal performance, read this manual before using the copier. Be sure to handle the
machine and perform all copying operations only as recommended in the manual. Keep
the manual located with the machine so that all users may refer to it, as needed.
Manual Organization:
This manual includes fifteen topic sections as well as product specifications. Highlights are
as follows:
Section 1: General product information and features.
Section 2: Safety information to be read before operating this equipment.
Section 3: Machine information to be used as a reference when performing all copying
jobs, especially when capacities, sizes and weights are factors.
Section 4: Paper information to be used as a reference when performing all copying jobs.
Section 5: Copier management information to be read before operating this equipment.
Section 6: Information on using the touch screen and selecting basic copying functions.
Section 7: Information on output modes, including sort, staple-sort, group, punching, face
up, folding/stapling & folding, three-folding, cover sheet feed, and manual
finishing functions.
Section 8: Information on special original modes.
Section 9: Information on special applications modes.
Section 10: Information on program memory functions.
Section 11: Information on server functions for storing the image data in HDD during printing.
Section 12: Shortcuts for special application functions and some basic functions.
Section 13: Information on key operator functions for customizing the machine to suit your
working environment. The key operator mode should be used by an
authorized person.
Section 14: Information on maintaining this equipment and replenishing paper and toner.
Section 15: Troubleshooting information and instructions for clearing mishandled paper.
Section 16: Machine specifications for the main body and accessories.
Page Design:
The page layout of this manual is designed to help you perform each operation quickly and
easily. The basic format includes an introductory explanation of each function, step-by-
step procedures, and illustrations to enhance many of the procedures. Caution statements
specific to a topic are located on appropriate pages. Special notes are located at the
bottom of the page.
Help Mode
Help can be obtained for any function or mode that is displayed on the screen.
Introduction 1-3
Introduction
Product Overview
The DL650 is a digital printer/copier that can be used as a stand-alone copier or as a high-
speed network printer when connected to the optional Printer Controller.
The DL650 can also be used as a print server on a network operating system.
Separate operating manuals and installation instructions are included with the optional
Printer Controller.
Digital technology and memory capability of the DL650 provide many advantages over the
conventional photocopying process.
In conventional photocopying, a scanned image virtually remains intact as it is represented
on the drum and then copied onto the output media. While many conventional settings can
be made before outputting the copies to effect image reduction, lens adjustment, image
erasure and job store, etc., the conventional photocopying process cannot transform the
image into bits or store image data into memory.
In the DL650, a scanned image is electronically digitized into data bits that are
represented in code form and stored into memory. Stored data can be retrieved from
memory and output in various ways, as controlled by software. The digitized image is
represented as pixels on a screen or as dots per inch (dpi) on hard copy. The DL650
resolves image in the copier/printer mode at 600 dpi.
DL650 digital technology enables you to:
• feed originals only once to make multiple copies, thereby preserving the condition of
originals
• store images in memory and perform Sheet/Cover insertion, Chapter, Combination,
Booklet, Image insert, Book copy, Program job, Mixed original, Repeat, Image shift,
Stamp/Overlay
• enhance photos, complex text image quality, and enhance lighter images
• reduce toner consumption and produce clean copies with Non-image area erase
• organize images into booklet format
• insert images scanned from the platen into a set scanned from the EDH (document
handler)
• check copying conditions and produce a proof copy before making multiple copied sets
• confirm the current machine status
• select offset-sort, offset-group, staple-sort, folding, or stapling & folding output mode
using optional Finisher (9940/9922)
• set reserve jobs to make copies of different types in succession
• overlay stamp, watermark, or scanned images on the scanned originals
• store image data in HDD (option) for future printing
1-4 Introduction
Introduction
Features of the DL650

• 600dpi Mode
Scans in higher resolution (600dpi).
• All-Image Area
Makes copies printed completely to the edges of the paper to avoid image loss.
• AES - Automatic Exposure Selection

Automatically adjusts exposure to compensate for quality of the original.
• AMS - Automatic Magnification Selection

Automatically selects an appropriate magnification ratio when Copy Size is selected
manually. Automatically selected when [AMS] key is touched.
• APS - Automatic Paper Selection

Automatically selects copy paper size to match the original documents.
• ATS - Automatic Tray Switching

Automatically switches trays to allow copying to continue without interruption if the
selected tray empties while copying is in progress.
• Auto Layout
The original image on the platen glass or in the EDH (document handler) is copied and
centered on a sheet.
• Auto Low Power

Automatically lowers the power after a specified period of copier inactivity.
• Auto Shut-Off
Automatically shuts off the main power after a specified period of copier inactivity.
• Book Copy
Copies both pages of an open book or book-size sheet separately onto two letter sheets in
1-1 mode or separately onto each side of one letter sheet in 1-2 mode. You can use the
Book Copy mode with the Front or Front/Back cover mode. The cover page(s) will be
scanned and copied normally before image division is performed on the other pages.
• Booklet
Creates letter R or ledger size booklets from letter size originals in 1-2 or 2-2 copy mode.
• Chapter
Starts chapter pages on the right side (front pages) of the finished document. Only duplex
mode (1-2 or 2-2) is compatible with this feature.
Introduction 1-5
Introduction
Features of the DL650 (continued)
• Combination
Copies a fixed number (2, 4, or 8) of pages onto one sheet of copy paper.
• Copy Density
Manually selects up to 9 density levels.
• Copy Mode
Selects the desired simplex mode (1-1 or 2-1); or duplex mode (1-2 or 2-2).
• Counter List
Displays on the screen and prints the following data: total counter of the machine, copier
counter, print counter and the date when the counter started.
• Density Shift
Shifts each of nine density levels in four density modes (Auto, Text, Photo, Increase
Contrast) to three levels lighter or three levels darker.
• Energy Saver
Automatically turns off all but nominal power supply after a specified period of copier
inactivity, for optimal efficiency. Power is returned after a brief warm up period by pressing
the [Energy Saver] key on the Control panel.
• Frame/Fold Erasure
Erases border and/or fold image area using Frame (1 - 300mm), Fold (1 - 99mm), or
Frame & Fold.
• HDD Store
While copying, stores image data in HDD (option) for future printing.
• Image Insert
Stores pages in memory from the platen glass, and inserts the pages into a document
copied from the EDH (document handler).
• Image Rotation
Image Rotation rotates the image before copying when the crosswise/lengthwise
orientation of the original is different from the orientation of the copy paper.
In 1-2 copy mode, Rotation arranges the even pages of simplex originals so that the
reverse sides of the duplex copies appear upside down.
In 2-1 copy mode, Rotation rearranges the reverse sides of duplex originals, when the
reverse side is upside down, so that they can be read as normal simplex copies.
1-6 Introduction
Introduction
• Image Shift
Creates or removes a binding margin at the top, bottom, right and left edges (shift amount
from 0 ~ 250mm, in 1mm increments); reduces image to prevent image loss (reduce &
shift amount from 0 ~ 250mm, in 1mm increments).
• Interrupt Copying
Interrupts copying in progress to perform copying from the platen glass.
• Job Status
Displays the Job Status Screen to view the machine status, changes the operation order of
reserve jobs, deletes the unused reserve job, or displays the previous job list.
• Lens Mode (Preset, Zoom)

Selects Preset ratios, three reduction and three enlargement ratios.
Zoom ratios can be selected from 25% ~ 400%, in 0.1% increments.
• Machine Status Confirmation

Displays the current machine status on LCD for confirmation.
• Magnification
Sets user-programmable ratios under Custom zoom 1, Custom zoom 2 and Custom zoom 3.
• Manual Shut-off
Shuts off the main power when pressing [Energy Saver] key.
• Mixed Original
Copies mixed size originals from the EDH (document handler) in APS or AMS mode. APS
automatically selects the copy size of each original. AMS mode allows you to select one
paper size for all originals.
• Non-Image Area Erase

When copying from the platen glass when the EDH (document handler) is open, copies
only the image area and not the exposed area of glass, which would otherwise copy as
black.
• Non STD Size for Multi-Sheet Bypass Tray

Enters the special paper size to be loaded on the Multi-sheet bypass tray using the touch
screen keypad in order to avoid paper misfeed.
• Non STD Size for Original

Identifies the special original size which the DL650 cannot detect, in order to select the
optimal paper size for copying or printing.
Introduction 1-7
Introduction
• Output mode for Machine with 9940/9922 Finisher Installed:

Non-Sort, Sort, Staple-Sort, and Group modes using the primary (main) tray
Non-Sort Face Down exit, Non-Sort Face Up exit, Group Face Down exit, and
Group Face Up exit modes using the secondary (sub) tray
Folding, Stapling & Folding, and 3-Folding modes using the booklet tray (9922
only)
Selects an output tray and output mode on the Finisher Mode Selection Screen and on the
Control panel. For details of each output mode, see Section 7: Output Modes.
• Output for Machine with no Finisher Installed: Sort and Group modes
Use the default condition to output copies in the same order as the originals. Use the Sort
mode to alternately switch the horizontal and vertical orientation of each copied set upon
exit. Use the Group mode to output multiple copies of each original without offsetting them
upon exit.
• Output mode for 9940/9922 Finisher with 9924 Cover Inserter Installed:
Cover Sheet mode
Manual Finishing mode
For details of each output mode, see Section 7: Output Modes.
• Overlay
Imprints a scanned image onto the copy image.
• Overlay Memory
Stores the overlaying image in HDD and prints a stored image onto the copy image.
• Panel Reset
Automatically resets to auto mode defaults after a specified period of copier inactivity.
• Paper Capacity
Total 2,600 sheets, including two 500-sheet trays, a 1,500-sheet tray, and a 100-sheet
Multi Sheet Bypass tray.
Total 6,600 sheets, including 4,000-sheet optional large capacity tray.
• Platen Memory
Scans documents into memory from the platen glass and/or the EDH (document handler)
and inserts the pages into another document copied from the EDH. If an incompatible
function is selected in this mode, the latter function will not be selected, and a Caution
message will be displayed.
1-8 Introduction
Introduction
• Program Job
Scans documents into memory while designating a different copy condition for each
original, then prints all the images collectively.
• Program Memory
Programs up to 30 jobs and recalls each job by job number, as needed. All compatible
platen glass functions can be programmed into Program Memory directly after they are
selected.
• Proof Copy
To ensure correct output before running multiple copies, run a proof copy by touching
PROOF COPY on the Mode Check Screen or pressing [Proof Copy] key on the Control
panel.
• Punching Mode for 9940/9922 Finisher with Punch Kit Installed:

Punches three holes in output copies.
• Repeat Image
Selects the horizontal image area across the page, and repeats it down the page as many
times as the repeat width setting (10 ~ 150mm) permits, in manual or auto.
• Reserve
Scans in subsequent copy jobs while the DL650 is busy printing or copying.
• Reverse Image
Reverses the image from black-on-white to white-on-black or vice versa.
• Rotation Exit (Rotation Sort/ Rotation Group)

When no Finisher is installed, Rotation Exit alternately switches the horizontal and vertical
orientation of each sorted set as it outputs to the exit tray. Be sure to load both 8.5"x11"
and 8.5"x11"R in separate trays (including the Multi-sheet bypass tray) before selecting
this feature.
• Server Function (option)

Stores image data in the HDD for future printing.
• Sheet/Cover Insertion
Inserts up to 30 blank or copied sheets from any tray including the Multi-Sheet Bypass
Tray, or inserts blank or copied front and back covers from any tray including the Multi-
sheet bypass tray.
Introduction 1-9
Introduction
• Stamp
Imprints a stamp, watermark, or scanned image onto the copy image.
• Staple
Selects the stapling position and number of staples (3 positions).
• STD Size (Special)

Detects the standard paper sizes which cannot normally be detected (A4R and A5) when
loaded in a main body tray. A5R and F4 sizes will also be available when loaded in the
Multi-sheet bypass tray.
• Tab Paper
Copies onto tabbed sheets from tabbed originals, allowing the image on the tab part of the
original to be printed on the same part of the tabbed copy paper.
• Text/Photo Enhance
Enhances photo image in Photo mode, regular image in Auto mode, text image in Text
mode, lighter image in Increase Contrast mode.
• Transparency Interleave
Copies onto transparency film and interleave blank or copied paper for each original
copied.
• Userset Density (USERSET 1, USERSET 2)

Outputs up to 16 density samples on a total of 4 pages that display 4 samples per page,
then programs the desired density under USERSET 1 and/or USERSET 2.
• Weekly Timer
Can be set according to the needs of each work environment. Turns main body power Off/
On daily or weekly, during lunch time, on holidays, and also enables the Timer Interrupt
mode, which allows temporary use of the machine even when the machine is in the daily,
weekly, or holiday Off Mode.
• Wide Size Paper

Copies onto paper slightly larger than the specified regular size.
• Z-Folded Original
This feature sets the EDH (document handler) to accept Z-folded originals.
1-10 Introduction
Introduction
Copier Features
Standard Equipment
Main Body with 3 Paper Trays (500/500/1,500 sheets)
Electronic Document Handler (EDH)
Automatic Duplex Unit (ADU)
Configuration Options:
with Multi-Sheet Bypass Tray (100 sheets)
Optional Equipment
Stapler Finisher (9940)
This Finisher is equipped with two exit trays.
Secondary (sub) tray: Four output types can be specified on the Finisher Mode
Selection Screen.
(1) Face-down non-sort exit
(2) Face-up non-sort exit
(3) Face-down group exit
(4) Face-up group exit
Primary (main) tray: Four output types can be specified by STAPLE SORT and SORT
keys on the Basic Screen and by the setting on the Finisher Mode Selection Screen.
Face-up exit is not available.
(1) Sort exit
(2) Staple sort exit
(3) Non-sort exit
(4) Group exit
Stapler Finisher (9922)

This Finisher is equipped with three exit trays and a 9924 Cover Inserter (option).
Secondary (sub) tray: Four output types can be specified on the Finisher Mode
Selection Screen.
(1) Face-down non-sort exit
(2) Face-up non-sort exit
(3) Face-down group exit
(4) Face-up group exit
Primary (main) tray: Four output types can be specified by STAPLE SORT and SORT
keys on the Basic Screen and by the setting on the Finisher Mode Selection Screen.
Face-up exit is not available.
(1) Sort exit
(2) Staple sort exit
(3) Non-sort exit
(4) Group exit
Booklet tray: Stapled and folded, or simply folded booklets are to be delivered onto this
tray. These two finishing modes can be specified on the Finisher Mode Selection
Screen.
Introduction 1-11
Introduction
Copier Features (continued)
Optional Equipment (continued)
Punch Kit
Used when selecting PUNCH on the Finisher Mode Selection Screen.
9924 Cover Inserter

Used when selecting COVER SHEET on the Finisher Mode Selection Screen, or when
stapling copies manually.
Large Capacity Cassette (9930) (4,000 sheets)
Large Capacity Cassette (9932) (4,000 sheets)
64MB Memory (M64-1) / 128MB Memory (M128-1)
Printer Controller
Hard Disk Drive Kit (DL6500020)
1-12 Introduction
DL650us02v1.fm 1 ページ２００１年１１月１４日　水曜日　午後２時５２分
Section 2: Safety Information
User Instructions
Machine Labels
Label Locations
Machine Installation and Power Requirements
Machine Handling and Care
Routine Safety
Finisher Capacity Requirements

Regulations
FCC Regulations
ICES Regulations
Laser Safety
Internal Laser Radiation
Laser Safety Label
Ozone Release
Safety Information 2-1

Safety Information
User Instructions
The following pages include important safety information, which you must read and
understand before you attempt to operate the machine. If you have any concerns about
safety matters, please contact your service representative. Keep this manual permanently
located with the machine, so that this safety information is readily availble.
Machine safety labels are attached to the internal area of the machine. The purpose of
safety labels is to alert you of imminent or potentially hazardous situations or conditions.
Be sure to heed all safety label information. If the safety labels become illegible due to
soilage, etc., please contact your service representative for information about label
replacements. Sample safety labels are shown on the following page.
TO AVOID GETTING BURNED Do not touch any part of the machine that you are advised
not to touch by a warning or caution label.
DO NOT REMOVE WARNING OR CAUTION LABELS

Clean labels as needed to maintain legibility. If any warning or caution label is removed or
becomes illegible from soilage, please contact your service representative for information
about label replacements.
The following standard safety categories are commonly used on product labelling.
DANGER:
Danger indicates an imminent hazardous situation, which, if not avoided, will result
in death or serious injury.
Note:
The DANGER category is not required for this product, and is only included here for general user
information.
WARNING:
Warning indicates a potentially hazardous situation, which, if not avoided, could
result in death or serious injury.
CAUTION:
Caution indicates a potentially hazardous situation, which, if not avoided, may
result in minor or moderate bodily injury.
NOTICE:
Notice provides information on the correct handling or use of the machine to prevent breakage of the
copier or some machine part, etc. It does not indicate concern for personal safety.
2-2 Safety Information

Safety Information
Machine Labels
Label Locations
CAUTION
DO NOT INSERT
your finger into the
two EDH hinge WARNING
portions; This area generates
otherwise you may high voltage. If touched,
be injured. electrical shock may
occur. DO NOT TOUCH.
CAUTION
ATTENTION
CAUTION
High temperature!
PRECAUCION
Do not touch.
Use care when clear- CUIDADO
ing paper.
ATTENTION
CAUTION
CAUTION
Température élevée!
Risque de brûlure.
Soyez prudent en
retirant la feuille
coincée.
PRECAUCION
The fixing unit is
very hot. To avoid The conveyance fixing
CAUTION
¡Temperatura alta!
No tocar.
Tener cuidado al getting burned, DO unit is heavy. Use care DO NOT put your hand between
remover el papel.
CUIDADO NOT TOUCH. and draw it out gently; the main body and developing
Alta temperatura!
Não toque!
Tenha cuidado ao
otherwise you may be fixing unit; otherwise you may
remover o papel.
injured. be injured.

Safety Information
Machine Labels (continued)
Label Locations (continued)

(Finisher with 9924 Cover Inserter only)
CAUTION
DO NOT insert your finger into the bottom of the
upper part of the feeder when returning to its
original position; otherwise you may be injured.
(All trays)
CAUTION
DO NOT put your hand
between the main body
(9940/9922 Finisher) and tray; otherwise you
may be injured.
CAUTION
Use care after opening the
(9922 Finisher only)
paper exit outlet. DO NOT put
your hand into it; otherwise
you may be injured.
CAUTION
Inside the lower paper exit outlet is
the roller drive unit. DO NOT put your
hand into it; otherwise you may be
injured.

Safety Information
Machine Labels (continued)
Label Locations (continued)
• Avoid getting burned.

Do not touch any machine area that you are advised not to touch by a warning/caution
label.
• Do not remove warning/caution labels.

If any warning/caution label is removed or if any warning/caution label or caution
indicator is illegible due to soilage, clean the label. If cleaning does not render the label
legible, please contact your service representative for information about label
replacements.

Safety Information
Machine Installation and Power Requirements

CAUTION:
FAILURE TO HEED THE FOLLOWING CAUTIONS MAY RESULT IN BODILY INJURY AND/OR
MACHINE DAMAGE.
❒ FIRE PREVENTION
Install machine away from flammable or volatile materials. Routinely check for abnormal
heat from power cord and/or plug.
❒ SHORT CIRCUIT FROM WATER DAMAGE

Do not install or operate this equipment outdoors near a lake, pond, or river, etc.; and do
not allow the machine to come in contact with splashes of rain, water, or any liquid.
❒ TEMPERATURE AND HUMIDITY

Install the machine away from direct sunlight, heat sources
(stoves, heaters) and cold temperatures (air conditioners).
Avoid any environment that is outside 50°~86°F (10°~30°C),
with 10~80% humidity.
❒ VENTILATION
Do not allow the machine to come in contact with dust or
ammonia gas, or fumes from printing or cleaning solutions, etc.;
otherwise, image quality will be poor. Install the machine in a Temperature
well-ventilated area, for comfort; otherwise, an ozone odor will
be detected during large copy runs. When in use, the copier
generates ozone in amounts too small to be hazardous to the
human body.
❒ VIBRATIONS
If the machine is constantly vibrated or jolted, trouble may
occur. Install the machine on a level, horizontal floor, free from
vibrations. Vibration
❒ SPACE ALLOTMENT
Install machine in an area with adequate space for performing copier operations, replacing
supply items, and conducting preventive maintenance. See Site Requirements, Section 3.
❒ MACHINE RELOCATION
Before moving the machine to another location, contact your service representative.

Safety Information
Machine Installation and Power Requirements (continued)

CAUTION:
FAILURE TO HEED THE FOLLOWING CAUTIONS MAY RESULT IN MACHINE DAMAGE,
OVERHEATING, RISK OF ELECTRICAL SHOCK, AND/OR PERSONAL INJURY.
❒ PLUG SOCKET
A plug socket is limited in capacity. Use an exclusive power source for this machine;
otherwise, overheating and/or smoking may occur. The total power consumption of the
main body, plus all peripherals, must not exceed the capacity of the main power supply.
Be sure the socket-outlet is near the equipment and is easily accessible.
❒ PLUG AND CORD (LEAD)

Unless the power plug is firmly inserted into the socket, overheating and/or smoking may
occur. Firmly insert the power cord plug into the electrical outlet before turning on the
copier power switch. If the inserted plug is loose in the socket, disconnect it, and consult
an electrician for repair; do not attempt to operate the machine.
Be sure the socket-outlet is near the equipment and is easily accessible.
A damaged power cord may result in overheating, short circuit or fire. Do not bend, crush,
wind, kick, or strike the cord with any item. Do not roll up the cord. If the main body power
cord is bent or damaged, immediately contact your service representative; do not attempt
to repair it yourself; do not continue to operate the machine.
❒ ADAPTERS AND PLURAL LOADS

Never use adapters and never connect plural loads or a branched socket to one socket
outlet; otherwise, overheating or fire may occur.
❒ EXTENSION CORDS (LEADS)

An extension cord or lead is limited in capacity. Unless the cord or lead has adequate
capacity, smoking and overheating may occur. Should smoking and/or overheating occur,
contact an electrician immediately. If you require further information about power
requirements, power consumption, extension cords, adapters and connectors, please
contact your service representative, and consult your electrician.

Safety Information
Machine Handling and Care

WARNING:
FAILURE TO HEED THE FOLLOWING WARNING MAY RESULT IN DEATH OR SERIOUS INJURY AND/
OR MACHINE DAMAGE.
❒ MACHINE CONTACT
Never touch internal high voltage area indicated with a WARNING label.
Never touch the drum surface.
Never put your hand into the developing unit when removing mishandled paper.
CAUTION:
OVERHEATING, AND/OR PERSONAL INJURY.
❒ MACHINE CONTACT
Never touch internal high temperature or magnetism areas indicated with a CAUTION label.
Never insert your hand into the fixing unit when removing mishandled paper.
Never touch the inside of the main body for any purpose except
removing mishandled paper or adding toner.
Use care when pulling out the conveyance fixing unit.
❒ MACHINE CARE
Do not drop paper clips, staples or other small metallic objects
into the copier, or spill water or any other liquid into the
machine.
Do not use the machine surface to support vases, books, etc.
These items will interfere with the work space and may cause
damage to the machine or to original documents.
❒ ABNORMAL CONDITIONS
If any abnormal sound, odor, or smoke generates from the
machine, immediately stop using the copier, turn off the main
power switch, disconnect the plug and contact your service
representative.
If a circuit breaker is tripped, or if a fuse blows, stop using the machine and contact an
electrician. If more detailed information is needed regarding the power source or power
consumption of this machine, contact your service representative.
❒ MACHINE MODIFICATION
Do not modify the machine in any way or remove any part or screw. Never attempt to
perform any maintenance function that is not specifically described in this manual. Do not
connect the machine with any options other than those specified.

Safety Information
Routine Safety
CAUTION:
OVERHEATING, AND/OR PERSONAL INJURY.
❒ PERIODIC CHECK
Check for loose connection or excessive heat on power plug, damage to power cord and/
or plug (creased, frayed, scratched or cut, etc.). Be sure the plug is inserted fully, and
ground wire is connected correctly. If any abnormality occurs, do not continue to operate
the machine.
❒ SERVICE MESSAGES
If a service message displays, turn the machine off, disconnect the power cord from the
outlet, and report the condition to your service representative.
❒ TONER
Check to be sure toner in storage is out of the reach of children, or anyone incapable of
using supplies safely. Although toner is nontoxic, do not inhale toner or allow it to come in
contact with eyes. If inhalation or eye contact occurs, immediately consult a physician.
Please refer to the appropriate material safety data sheet for additional toner safety
information.
❒ PAPER
Check paper to be sure it is according to the specifications outlined in Section 4.
❒ CLEANING MATERIALS
Check the type of cleaning material used on your machine to be sure it is recommended
by us. If necessary, check with your service representative. Never use cleaning materials
for purposes other than cleaning, and be sure to keep all cleaning materials out of the
reach of children or anyone who is incapable of using them safely.
❒ ENERGY SAVER
Use Energy Saver mode for short periods of machine inactivity. When not using the
machine for long periods of time, turn power off, unless the weekly timer function is
operating.
❒ DISPOSAL OF THE COPIER

Dispose of this copier according to your local regulations.

Safety Information
Finisher Capacity Requirements

CAUTION:
MACHINE DAMAGE.
❒ FINISHER PAPER CAPACITY

To prevent paper misfeed, do not exceed the paper capacity of the Finisher.
9940/9922 Finisher paper weight: 16 lb ~ 24 lb
When the selected print quantity exceeds the maximum paper capacity, remove the copied
sheets from the finisher while the paper is exiting.
Paper capacities below are stated for 20 lb bond or the same size.
This Finisher also accepts wide types of the regular sizes stated below.
Finisher 9940/9922
Primary (Main) tray: Non-sort/Sort/Group mode
500 sheets (5.5"x8.5"R)
3,000 sheets (8.5"x11", 8.5"x11"R)(9940)
2,500 sheets (8.5"x11", 8.5"x11"R)(9922)
1,500 sheets (11"x17", 8.5"x14")
The Secondary (sub) tray can be unloaded while the DL650 is running. Set
production is not limited by the capacity of the Secondary (sub) tray.
Primary (Main) tray: Punching mode (machine with Punch kit only)
3,000 sheets (8.5"x11")
1,500 sheets (11"x17")
The Secondary (sub) tray can be unloaded while the DL650 is running. Set
production is not limited by the capacity of the Secondary (sub) tray.
Primary (Main) tray: Staple-Sort mode

1,000 sheets* (11"x17" ~ 8.5"x11"/R)
* The maximum capacity varies according to the number of copies to be stapled.
See p. 4-9.
Secondary (Sub) tray: Non-sort mode

200 sheets max.

Safety Information
Finisher Capacity Requirements (continued)

CAUTION:
MACHINE DAMAGE.
❒ FINISHER PAPER CAPACITY (continued)

Booklet tray (9922 only)
100 sheets max. (11"x17", 8.5"x14")
75 sheets max. (8.5"x11"R, A4R)
50 sheets max. in Three-Folding mode
(The maximum number of sheets varies, depending on the number of pages in the
booklet and whether Folding or Stapling & Folding is selected. See p. 4-10.)
❒ 9922 FINISHER BOOKLET MODE OUTLET

Inside the Booklet mode outlet is the roller drive unit. DO NOT put your hand into it when
removing the folded or stapled & folded sheet; otherwise you may be injured.
❒ 9940/9922 FINISHER PAPER EXIT OUTLET

To avoid injury when stapling large size copies, DO NOT put your hand into the open
Paper exit outlet.

Safety Information
Regulations
FCC Regulations
WARNING
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate ratio frequency
energy and if not installed and used in accordance with the operating manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be required to
correct the interference at his own expense.
The design and production of this unit conform to FCC Regulations, and any changes or
modifications must be registered with the FCC and are subject to FCC control. Any
changes made by the purchaser or user without first contacting the manufacturer will be
subject to penalty under FCC regulations.
This device must be used with shielded interface cables. The use of non-shielded cable is
likely to result in interference with radio communications and is prohibited under FCC
rules.
FCC-F01
ICES Regulations
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
IC-F03
Laser Safety
This is a digital machine which operates by means of a laser. There is no possibility of
danger from the laser, provided the machine is operated according to the instructions in
this manual.
Since radiation emitted by the laser is completely confined within protective housing, the
laser beam cannot escape from the machine during any phase of user operation.
This machine is certified as a Class 1 laser product. This means the machine does not
produce hazardous laser radiation.

Safety Information
Regulations (continued)
Internal Laser Radiation
Maximum Average Radiant Power: 340 µW at the laser aperture of the print head unit.
Wavelength: 775-800 nm
This product employs a Class IIIb Laser Diode that emits an invisible laser beam.
The Laser Diode and Scanning Polygon Mirror are incorporated in the print head unit.
The print head unit is NOT A FIELD SERVICE ITEM.
Therefore, the print head unit should not be opened under any circumstances.
Printer head unit
DANGER
INVISIBLE LASER RADIATION WHEN OPEN.
AVOID DIRECT EXPOSURE TO BEAM.
VORSICHT
UNSICHTBARE LASERSTRAHLUNG,
WENN ABDECKUNG GEÖFFNET. NICHT DEM
STRAHL AUSSETZEN. 注意
DANGER ここを開くとレーザー光が出ます。
RAYON LASER INVISIBLE LORS DE ビームを直接見たり、触れたり
L’OUVERTURE.
EVITER L’EXPOSITION DIRECTE. しないでください。

Safety Information
For the United States

CDRH regulation
This machine is certified as a Class 1 Laser product under the Radiation Performance
Standard according to the Food, Drug and Cosmetic Act of 1990. Compliance is
mandatory for Laser products marketed in the United States and is reported to the Center
for Devices and Radiological Health (CDRH) of the U.S. Food and Drug Administration of
the U.S. Department of Health and Human Services (DHHS). This means that the device
does not produces hazardous laser radiation.
The label shown on page 2-16 indicates compliance with the CDRH regulations and must
be attached to laser products marketed in the United States.
CAUTION:
Use of controls, adjustments or performance of procedures other than those specified in this
manual may result in hazardous radiation exposure.
This is a semiconductor laser. The maximum power of the laser diode is 15 mW and the
wavelength is 775-800 nm.
For European Users
CAUTION:
Use of controls, adjustments or performance of procedures other than those specified in this
manual may result in hazardous radiation exposure.
This is a semiconductor laser. The maximum power of the laser diode is 15 mW and the
wavelength is 775-800 nm.
For Denmark Users
ADVARSEL
Usynlig laserstråling ved åbning, når sikkerhedsafbrydere er ude af funktion. Undgå udsættelse
for stråling. Klasse 1 laser produkt der opfylder IEC60825 sikkerheds kravene.
Dansk: Dette er en halvlederlaser. Laserdiodens højeste styrke er 15 mW og

bølgelængden er 775-800 nm.

Safety Information
For Finland, Sweden Users
LOUKAN 1 LASERLAITE
KLASS 1 LASER APPARAT
VAROITUS!
Laitteen Käyttäminen muulla kuin tässä käyttöohjeessa mainitulla tavalla saattaa altistaa
käyttäjän turvallisuusluokan 1 ylittävälle näkymättömälle lasersäteilylle.
Tämä on puolijohdelaser. Laserdiodin suurin teho on 15 mW ja aallonpituus on 775-800 nm.
VARNING!
Om apparaten används på annat sätt än i denna bruksanvisning specificerats, kan användaren
utsättas för osynlig laserstrålning, som överskrider gränsen för laserklass 1.
Det här är en halvledarlaser. Den maximala effekten för laserdioden är 15 mW och

våglängden är 775-800 nm.
VARO!
Avattaessa ja suojalukitus ohitettaessa olet alttiina näkymättömälle lasersäteilylle. Älä katso
säteeseen.
VARNING!
Osynlig laserstrålning när denna del är öppnad och spärren är urkopplad. Betrakta ej strålen.
For Norway Users
ADVERSEL
Dersom apparatet brukes på annen måte enn spesifisert i denne bruksanvisning, kan brukeren
utsettes for unsynlig laserstråling som overskrider grensen for laser klass 1.
Dette en halvleder laser. Maksimal effekt till laserdiode er 15 mW og bølgelengde er 775-

800 nm.

Safety Information
Laser Safety Label
A laser safety label is attached to the outside of the machine as shown below.
CLASS 1 LASER PRODUCT

APPAREIL A RAYONNEMENT
LASER DE CLASSE 1
LASER KLASSE 1

Safety Information
Ozone Release
NOTE
= Locate the Machine in a Well Ventilated Room =
A negligible amount of ozone is generated during normal operation of this machine. An
unpleasant odor may, however, be created in poorly ventilated rooms during extensive
machine operations. For a comfortable, healthy, and safe operating environment, it is
recommended that the room well ventilated.
REMARQUE
= Placer l’appareil dans une pièce largement ventilée =
Une quantité d’ozone négligable est dégagée pendant le fonctionnement de l’appareil
quand celui-ci est utilisé normalement. Cependant, une odeur désagréable peut être
ressentie dans les pièces dont l’aération est insuffisante et lorsque une utilisation
prolongée de l’appareil est effectuée. Pour avoir la certitude de travailler dans un
environnement réunissant des conditions de confort, santé et de sécurité, il est préférable
de bien aérer la pièce ou se trouve l’appareil.

DL650us03v1.fm 1 ページ２００１年１１月１４日　水曜日　午後２時５３分
Section 3: Machine Information
Machine Configuration
External Machine Call-Outs
Internal Machine Call-Outs
Optional Equipment
Site Requirements
Control Panel Layout
Touch Screen
Basic Screen
Initial Settings
Auto Reset Mode
Automatic Paper Selection (APS)
Automatic Magnification Selection (AMS)
Automatic Exposure Selection (AES)
Automatic Tray Switching (ATS)
Lead Edge Delete
Service Settings
Finisher-Paper Capacity
Key Operator Password
ECM Master Key Code
Weekly Timer Master Key Code
HDD Management Password
Staple Sheet Capacity
Basic Operations 3-1

Machine Information
Machine Configuration
External Machine
!7 Control panel q EDH

!6 LCD Touch screen w Toner access door
!4 Power switch e Work table
r Key counter
(option)
!2 9940 Finisher t Multi-sheet

(option) bypass tray
!5 Main power switch
!1 Front doors
!0 Tray 1
o Tray 2
(Rear-left side of
main body) i Tray 3 u Right side
door y 9930 Large
!3 9924 Cover capacity cassette
inserter (option) (option)
y 9932 Large
capacity cassette
(option)
!2 9922 Finisher
(option)
3-2 Basic Operations

Machine Information
Machine Configuration (continued)
External Machine Call-outs
1 EDH (Electronic Document Handler) automatically feeds multiple originals one at a

time to the platen glass for copying.
2 Toner access door opens to replenish the toner.
3 Work table provides a convenient workspace for documents both before and after
copying.
4 Key counter (option) manages the number of copies made on the machine.
5 Multi-sheet bypass tray used for small quantity copying onto plain paper or special
paper.
6 LCC: Large capacity cassette 9930/9932 option holds 4,000 sheets.
7 Right side door opens to allow removal of mishandled paper.
8 Tray 3 (universal tray) is user-adjustable and holds 1,500 sheets of either 11"x17"/
8.5"x14"/8.5"x11"R or 5.5"x8.5".
9 Tray 2 (universal tray) is user-adjustable and holds 500 sheets of either 11"x17"/
8.5"x14"/8.5"x11"R or 5.5"x8.5".
10 Tray 1 (universal tray) is user-adjustable and holds 500 sheets of either 11"x17"/
8.5"x14"/8.5"x11"R or 5.5"x8.5".
NOTE: Tray 1, 2, 3, and LCC are available for loading wide types of the regular sizes specified above.
11 Front doors open to the internal copier to allow clearing of mishandled paper.
12 9940/9922 Finisher (option) sorts, staple-sorts, and groups into finished sets.
With Punch kit (option) installed, file holes can be punched in the output copies. 9922
folds or staples & folds copies into booklet-styled sets, and also folds max. 3 copies in
three.
13 9924 Cover Inserter (option) loads cover sheet paper and feeds the sheet as cover.
14 Power switch turns copier power On/Off when pressed.
15 Main power switch turns machine power On/Off to operate it as copier/scan/printer.
16 LCD touch screen displays interactive operation screens.
17 Control panel controls copier operations.

Machine Information
Internal Machine
u Total counter q Toner cartridge
w Toner cartridge
y Fixing unit holder lever
e Conveyance/
Fixing unit
t Drum unit
r Lever A
Internal Machine Call-outs

1 Toner cartridge holds toner and is to be replaced when supplying toner.
2 Toner cartridge holder lever can be pulled forward to withdraw the toner cartridge
holder for replacing the toner cartridge.
3 Conveyance/Fixing unit passes the paper through the drum unit, and fuses the
toner onto the copy paper, and is to be withdrawn for removal of mishandled paper.
4 Lever A can be moved to withdraw the conveyance fixing unit for removal of
mishandled paper.
5 Drum unit forms the copy image.
6 Fixing unit fuses the toner onto the copy paper.
7 Total counter indicates the total number of copies and prints made.

Machine Information
Optional Equipment
Punch kit
Printer Controller
64MB Memory (M64-1) /

9924 Cover inserter 128MB Memory (M128-1)
DL6500020 Hard disk drive kit
Key counter
9940 Finisher
9930 Large capacity

cassette
DL650 main body
9932 Large capacity

9922 Finisher cassette

Machine Information
t Secondary t Secondary
(Sub) tray q Finisher door (Sub) tray q Finisher door
r Primary r Primary
(Main) tray (Main) tray
e Booklet tray w Booklet mode outlet
(9922 Finisher only) (9922 Finisher only)
9940 Finisher 9922 Finisher
1 Finisher door opens to the internal Finisher to allow clearing mishandled paper,
replenishing staples, and emptying trash basket of Punch kit.
2 Booklet mode outlet (9922 Finisher only) ejects finished copied sets when selecting
Folding mode, Stapling & Folding mode, or Three-folding mode.
3 Booklet tray (9922 Finisher only) holds sets ejected in Folding mode, Stapling &
Folding mode, or Three-folding mode.
4 Primary (Main) tray holds sets ejected in Non-sort mode, Sort mode (offset), Staple-
sort mode, or Group mode (offset).
5 Secondary (Sub) tray holds sets ejected in Non-sort mode or Group mode with face
down/up mode.

Machine Information

r Sub tray r Sub tray
conveyance lever conveyance lever
e Cover sheet e Cover sheet
conveyance conveyance
lever lever
t Stacker
conveyance
lever w Punch kit (option)
q Entrance lever
q Entrance lever
o Trash basket
i Stacker unit
u Stacker unit
knob
y Lower lever
9940 Finisher 9922 Finisher with

Punch kit
!0 Cartridge housing
!1 Stacker unit handle
1 Entrance lever opens downward to remove mishandled paper.

2 Punch kit (option) punches file holes in the output copies.
3 Cover sheet conveyance lever opens leftward to remove mishandled paper.
4 Sub tray conveyance lever opens rightward to remove mishandled paper.
5 Stacker conveyance lever opens leftward to remove mishandled paper.
6 Lower lever opens leftward to remove mishandled paper.
7 Stacker unit knob can be turned to ease removal of mishandled paper from the
Stacker unit.
8 Stacker unit folds or staples & folds copies into booklet-styled sets, and also folds
max. 3 copies in three.
9 Trash basket holds waste paper punched out.
10 Cartridge housing holds staple cartridge and is to be replaced when supplying staples.
11 Stacker unit handle withdraws unit to allow removal of mishandled paper and
replacement of staple cartridge.
Machine Information
e Upper tray guide plates

r Upper tray
w Upper unit release lever
t Lower tray
y Lower tray
guide plates
q Cover inserter
control panel
9924 Cover Inserter
1 Cover inserter control panel controls Cover inserter operations.

2 Upper unit release lever can be moved to slide the upper unit of Cover inserter for
removal of mishandled paper.
3 Upper tray guide plates hold cover sheets to fix the position.
4 Upper tray holds cover sheets for use in cover sheet output mode.
5 Lower tray holds cover sheets for use in cover sheet output mode or a copied set in
manual stapling/punching/three-folding mode.
6 Lower tray guide plates hold cover sheets to fix the position.

Machine Information
w LCC left q LCC top door w LCC left q LCC top door
side door side door
e LCC lever e LCC lever
r LCC paper guides
r LCC paper guides

y LCC bottom plate
y LCC bottom plate
u Rear stopper
t Paper loading
button
u Rear stopper
t Paper loading 9930 Large capacity cassette

button 9932 Large capacity cassette
1 LCC top door opens to allow paper loading.

2 LCC left side door opens to allow removal of mishandled paper.
3 LCC lever can be moved downward to ease removal of mishandled paper.
4 LCC paper guides hold copy paper to fix the position.
5 Paper loading button is pressed to lower the bottom plate to allow loading paper.
6 LCC bottom plate goes up automatically when paper supply becomes low, and goes
down when the paper loading button is pressed.
7 Rear stopper fixes the rear end of copy paper.

Machine Information
Site Requirements
Unit: inches (mm)

4.7
(120)
18.7 25.6 15.7 37.4 31.1
(475) (650) (400) (950) (790)
18.9
(480)
63.8
(1620)
44.9
(1140)
60.0 73.2
(1525) (1860)
DL650
Unit: inches (mm)

3.9 3.9 4.7
(100) 29.2 (100) (120)
(741) 25.6 16.9 37.4 31.1
25.8 (650) (430) (950) (790)
(656) 16.1
(410)
63.8 63.8
(1620) (1620)
44.9
(1140) 39.0
(990)
79.5 73.2
(2021) (1860)
DL650 + 9940 Finisher + 9930 Large capacity cassette

Machine Information
Site Requirements (continued)
Unit: inches (mm)

3.9 3.9 4.7
(100) 13.0 16.1 (100) (120)
(331) (410) 25.6 26.4 37.4 31.1
(650) (670) (950) (790)
25.8
29.2 (656)
(741)
63.8
(1620) 63.8
(1620)
44.9
(1140)
39.0
(990)
89.0 73.2
(2261) (1860)
DL650 + 9922 Finisher + 9924 Cover inserter + 9932 Large capacity cassette
NOTES:
1 Dimensions are in inches with millimeters included in parentheses.
2 The Finisher main tray of the 9940/9922 Finisher gradually goes down while printed material is output. DO
NOT allow any object to interfere with the operation of the tray on the left side of the Finisher, as interference
may cause damage to the Finisher.

Machine Information
Control Panel Layout
q w
e r t y u
Help Print Copy Scan
Program Memory
Mode Check Energy Saver

Timer
Utility Interrupt
Start
Stop
Panel Reset
Proof Copy
!6 !5 !4 !3 !2 !1 !0 o i
1 Power switch turns copier power On/Off when pressed.

2 LCD Touch Screen displays machine and copying status, help information, interactive
screens, and touch keys for selecting all functions.
3 Program Memory displays screens for selecting job store/job recall functions.
4 Help displays a screen with help for the currently selected function, or to access the
Key Operator Mode Screen.
5 Mode Check displays a screen showing all settings that are selected for the current
job.
6 Keypad enters numeric values.
7 Timer lights when the timer function is set.
8 Mode switches the machine operation mode to copy, scan, and print in turn.
9 Energy Saver activates energy-saving mode for times when the copier is inactive, or
activates timer interrupt mode when weekly timer function is active.
10 Panel Reset restores copier to automatic mode settings or to Key Operator settings.
11 Interrupt stops copying in progress to allow copying from the platen glass.
12 [C] (Clear) allows resetting of print quantity.
13 Stop stops the copying sequence; deletes the stored memory.
14 Start activates copying or scanning.
15 Utility displays the Counter Screen or accesses programming modes for setting
special functions.
16 Proof Copy outputs a single set of copies to confirm whether the current settings are
selected properly.
Machine Information
Touch Screen
The touch screen is an LCD that displays interactive screens with touch sensitive keys for
making copy job selections. Selections are highlighted at the touch. The screens also work
with the conventional control panel keys.
CAUTION:
The touch screen of the control panel is covered with glass. Do not drop heavy items on the glass, or put
excess weight or pressure on it; otherwise the glass may break or become scratched.
After the power switch is turned on, the Warm-Up Screen displays for approximately 6.0
minutes, until the fixing temperature is reached.
When the Basic Screen is displayed, the touch screen becomes interactive. The interactive
condition enables you to communicate directly with the copier system simply by touching
keys displayed on the screen; or by pressing conventional keys, as required. In addition,
the screens automatically display information regarding machine and copying status.
Additional help is available any time with the [Help] key, which can be pressed from any
screen, except from Program Memory or Key Operator Mode Screens.
Basic Screen
The Basic Screen displays after warm-up. Initial settings are shown on the next page.
Except for Print Quantity, all initial settings can be changed by the Key Operator.
The following modes can be accessed from this screen:

Copy Mode, Copy Density, Lens Mode, Copy Size, Special Original, Application, Output.

Machine Information
Initial Settings
Initial settings represent the initial condition when power is turned on; when ECM
password is set; or when Panel Reset mode is restored, either manually or automatically.
Print Quantity: 1
Magnification Ratio: 1:1 (Key Operator setting)
EDH: ON (Key Operator setting)
Copy mode: 1-1 mode (Key Operator setting)
AES: (Automatic Exposure Selection) : ON (Key Operator setting)
APS: (Automatic Paper Selection): ON (Key Operator setting)
Finisher: Non-sort on Primary (main) exit tray (Key Operator setting)
Panel Reset Mode

The Panel Reset function can be set for OFF/ 30 seconds/ 1 minute/ 1.5 minutes/ 2
minutes/ 2.5 minutes/ 3 minutes/ 3.5 minutes/ 4 minutes/ 4.5 minutes/ 5 minutes by the
Key Operator. Initially, the mode is set to function after 1 minute of copier inactivity. The
Panel Reset key function also re-displays the Basic Screen, unless these settings are
changed by the Key Operator in the Copier Initial Setting Screen. See p. 13-13 to p. 13-14.

When APS is highlighted on the touch screen, the appropriate copy paper size is
automatically selected. When copying from the platen glass or EDH, APS detects the sizes
indicated below. For Key Operator settings of APS, see p. 13-43 to p. 13-49.
PLATEN GLASS: 11"x17", 8.5"x14", 8.5"x11", 8.5"x11"R, 5.5"x8.5"
EDH: 11"x17", 8.5"x14", 8.5"x11", 8.5"x11"R, 5.5"x8.5", 5.5"x8.5"R, A4 (8.27"x11.69", 210mmx297mm)

AMS functions automatically. An appropriate ratio is selected, based on the relationship of
copy size to original size.

When AES is highlighted on the touch screen, the appropriate exposure level is
automatically selected to match the copy density of the original. Manual density
adjustments override AES.
Automatic Tray Switching (ATS)

When the selected paper tray becomes empty while copying is in progress, automatic tray
switching detects the same copy paper size loaded in another tray to allow copying to be
continued without interruption. The Multi-sheet bypass tray is not included in tray
switching.

Machine Information
Lead Edge Delete
When using the EDH, image deletion of a few millimeters will occur on the lead edge for
the purpose of controlling copy quality and copy reliability, unless deactivated by the Key
Operator. See p. 13-43 to p. 13-49.
Service Settings
The following functions can be provided by your service representative, who is authorized
to change DIP switch settings. Contact your service representative if setting change is
required.
Finisher-Paper Capacity
In the default condition, the DL650 will produce unlimited sets. If required, your service
representative can set the copier to stop copying when the number of copies exceeds
specified capacity.
Key Operator Password

Your service representative can set a 4-digit Key Operator password to access the Key
Operator Mode Screen. After this setting, a Password Entry Screen will display and require
entry of the Key Operator password to access the Key Operator Mode Screen.
ECM Master Key Code

Your service representative can set an 8-digit ECM master key code to access the ECM
Setting Menu Screen. After this setting, the ECM Master Key Code Screen will be
displayed and will always require entry of the set ECM master key code to access the ECM
Setting Menu Screen.
Weekly Timer Master Key Code

Your service representative can set a 4-digit Weekly Timer master key code to access the
Weekly Timer Setting Menu Screen. After this setting, the Weekly Timer Master Key Code
Screen will be displayed and will always require entry of the set Weekly Timer master key
code to access the Weekly Timer Setting Menu Screen.

Machine Information
Service Settings (continued)
HDD Management Password
Your service representative can set a 4-digit HDD management password to access the
HDD Management Setting Menu Screen. After this setting, a Password Entry Screen will
display and require entry of the HDD management password to access the HDD
Management Setting Menu Screen.
Staple Sheet Capacity

Staple capacity is changeable, and may be set to 45, 40, or 35 by your service
representative.

DL650us04v1.fm 1 ページ２００１年１１月１４日　水曜日　午後２時５４分
Section 4: Paper Information
Positioning Originals on the Platen Glass

Positioning an Original for Manual Copying
Using the Electronic Document Handler (EDH)

Positioning Originals
Positioning Mixed Originals
Paper in Main Body Trays

Paper in 9930 Large Capacity Cassette (Option)
Paper in Automatic Duplex Unit
Paper in Multi-Sheet Bypass Tray
Paper in 9940/9922 Finisher (Option)
9940/9922 Finisher Primary (Main) Tray
9940/9922 Finisher Secondary (Sub) Tray
9922 Finisher Booklet Tray
Paper in 9924 Cover Inserter (Option)

Paper in Punch Kit (Option)
Paper Weight Compatibility Chart
Paper Information 4-1

Paper Information
Positioning Originals on the Platen Glass
Positioning an Original for Manual Copying
Use the platen glass when originals are not suitable for use with the EDH, e.g., when size
is incompatible, or when originals are folded, stapled, torn, or in generally poor condition.
Specifications
❒ Max. original size: 11"x17" (280mm x 432mm), sheet or book
❒ Max. book weight/thickness: 15 lb [6.8kg]/1.2" [30mm]
❒ Original placement: Face down on right depth side of glass
1 Raise the EDH, as shown in the illustration below.

2 Place original FACE DOWN in the left rear corner, aligning the edge with the left and
rear measuring guides.
3 Gently close the EDH, to prevent the original from shifting on the glass.
CAUTION:
When the selected print quantity exceeds the Finisher’s maximum capacity, remove the printed sheets
while paper is exiting to avoid paper mishandling.
TIP:
To eliminate black copy marks on edges when copying from a book without selecting Book Copy mode, select
Frame/Fold Erasure or Non-Image Area Erase in Application mode.
4-2 Paper Information

Paper Information
Using the Electronic Document Handler (EDH)
Specifications in 1-1, 1-2, 2-2, 2-1 Copying

❒ Original size: 11"x17", 8.5"x14", 8.5"x11", 8.5"x11"R, 5.5"x8.5", 5.5"x8.5"R, A4
(297mm x 432mm~140mm x 216mm)
❒ Original weight: 13 lb~34 lb
❒ Max. feeder capacity: 100 original sheets (20 lb bond paper)
❒ Max. original exit tray capacity: 100 original sheets (20 lb bond paper)
❒ Original placement: Face up; orientation same as copy paper
❒ Curling tolerance: 10mm or less
Using Mixed Original Mode*

❒ Original size: 11"x17", 8.5"x14", 8.5"x11", 8.5"x11"R, 5.5"x8.5"R mixed
(5.5"x8.5" original is available in crosswise type feeding only)
❒ Mixed feeder capacity: 100 original sheets (20 lb bond paper)
*See p. 8-6 to p. 8-7 for details of the Mixed Original mode.
Unsuitable EDH Originals

1 2 3
Curled, creased or Paste-ups

folded originals or cut-outs Books
4 5 6
Glossy or transparent (OHP) Folded, punched

film, art paper, cellophane or stapled originals Thin or thick originals

Paper Information
Using the Electronic Document Handler (EDH) (continued)
Positioning Originals
The EDH automatically feeds up to 100 originals directly to the platen glass, starting with
the top sheet. The EDH should only be used for unstapled, unfolded, smooth, flat originals.
❒ Original size detection requires accurate paper guide adjustment.

❒ APS detects size 11"x17", 8.5"x14", 8.5"x11", 8.5"x11"R, 5.5"x8.5", 5.5"x8.5"R, and A4.
❒ Size, weight, and capacity are specified for all copy modes on p. 4-3.
Before placing originals in the tray, be sure the EDH is closed fully.
1 Position original(s) FACE UP on the EDH tray.
Place two-sided originals with page one FACE UP.
2 Adjust paper guides.

Paper Information
Using the Electronic Document Handler (EDH) (continued)
Positioning Mixed Originals
Mixed size originals can be copied together from the EDH in either APS mode or AMS
mode. In APS mode, copies will be output on mixed paper sizes to match the originals. In
AMS mode, copies will be output on one common paper size that you select in which case
an appropriate AMS magnification ratio will be selected automatically. To use the mixed
original mode, see procedure on p. 8-6 to p. 8-7.
❒ Mixed original size: 11"x17", 8.5"x14", 8.5"x11", 8.5"x11"R, 5.5"x8.5"R, and 5.5"x8.5"* mixed
(13 lb~34 lb)
* 5.5"x8.5" original is available in crosswise type feeding only.
❒ EDH capacity: Max. 100 sheets (20 lb bond paper)
❒ Print quantity: Max. 9,999 sheets
❒ Incompatible Basic Copying Conditions: Rotation Exit, Staple-Sort with APS, Folding/Stapling &
Folding in APS, Punching in APS, Three-Folding
❒ Incompatible Special Originals: Non STD Size, Z-Folded Original, Tab Paper
❒ Incompatible Applications: Sheet/Cover Insertion, Chapter, Combination, Booklet, Transparency
Interleave, Image Insert, Book Copy, Program Job, Non-Image Area Erase, Repeat, AUTO
Layout, Overlay, Storing image in Overlay Memory
Before using the Mixed Original mode, be sure the EDH is closed completely.
1 Arrange originals in order, and place them as described below:
Place 11"x17"/8.5"x14" originals face up or side 1 up in the EDH, in lengthwise
orientation, i.e., with short edge feeding.
Position 8.5"x11" size in either crosswise or lengthwise orientation.
Position 5.5"x8.5" size in crosswise orientation only.
2 Position mixed originals FACE UP, aligned with the left rear side of the EDH tray.
3 Adjust paper guides to originals.

Paper Information
Paper in Main Body Trays
Paper Size: STD size: 11"x17", F4, 8.5"x14", 8.5"x11", 8.5"x11"R, 5.5"x8.5", A3,
B4, A4, A4R, B5, B5R, A5 (user-adjustable)
STD size (spec.): specify A4R instead of 8.5”x11R
specify A5 instead of 5.5”x8.5”
Non STD size: input the measures of paper between max.
314mmx459mm and min. 210mmx140mm.
Wide paper: 11"x17"W, 8.5"x11"W, 8.5"x11"WR, 5.5"x8.5"W, A3W,
B4W, A4W, A4WR, B5W, A5W (user-adjustable)
NOTES: • F4: 8"x13", 203mm x 330mm
A3: 11.69"x16.54", 297mm x 420mm
B4: 10.11"x14.33", 257mm x 364mm
A4: 8.27"x11.69", 210mm x 297mm
B5: 7.17"x10.11", 182mm x 257mm
A5: 5.85"x8.27", 148mm x 210mm
• 5.5"x8.5"/A5 copy paper is available in crosswise orientation loading only.
• 8.5"x14"W copy paper is not available.
• STD size (spec.)/Non STD size/Wide paper setting for each tray can be made in the Key Operator
mode. See p. 13-27 ~ p. 13-28.
Paper Weight: General tray: 16~24 lb

Tray specified in Thick : 25~110 lb (200 g/m2 thick paper)
Tray specified in Thin: 13~15 lb (1-1 or 2-1 copy mode only)
Tray specified in Tab paper: 25~45 lb (1-1 or 2-1 copy mode only)
NOTE: Paper type setting for each tray can be made in the Key Operator mode. See p. 13-27 ~ p. 13-28.
Paper Capacity: Tray 1/2: 500 sheets 20lb/ user-adjustable to any standard/wide size
from 11"x17"/W~5.5"x8.5"/W
Tray 3: 1,500 sheets 20lb/ user-adjustable to any standard/wide size
from 11"x17"/W~5.5"x8.5"/W
2,600 sheets, including 100-sheet Multi-Sheet Bypass Tray
NOTE: Reliability and copy quality are not guaranteed for all special papers. Use only paper that is
recommended by us.

Paper Information
Paper Size: 8.5"x11"

STD size: 8.5"x11", A4 (service-adjustable)
STD size (spec.): cannot be specified
Non STD size: input the measures of paper between max. 314mm x 223mm
and min. 257mm x 182mm
Wide paper: 8.5"x11"W, A4W (service-adjustable)
NOTE: Non STD size setting for LCC can be made in the Key Operator mode. See p. 13-27 ~ p. 13-28
.
Paper Weight: 16~24 lb
LCC specified in Thick : 25~110 lb (200 g/m2 thick paper)
LCC specified in Thin: 13~15 lb (1-1 or 2-1 copying only)
LCC specified in Tab paper: 25~45 lb (1-1 or 2-1 copy mode only)
NOTE: Paper type setting for LCC can be made in the Key Operator mode. See p. 13-27 ~ p. 13-28.
Paper Capacity: 4,000 sheets 20 lb/ fixed to standard/wide size 8.5"x11"/W or A4/W
6,600 sheets, including three Main body trays and 100-sheet Multi-Sheet
Bypass Tray
Paper Size: 11"x17"

STD size: 11”x17”, F4, 8.5”x14”, 8.5"x11", 8.5”x11”R, A3, B4, A4, A4R
(service-adjustable)
STD size (spec.): cannot be specified
Non STD size: input the measures of paper between max. 314mm x 459mm
and min. 257mm x 182mm
Wide paper: 11”x17”W, F4W, 8.5”x14”W, 8.5"x11"W, 8.5”x11”WR, A3W,
B4W, A4W, A4WR (service-adjustable)
Paper Weight: 16~24 lb
LCC specified in Thick: 25~110 lb (200 g/m2 thick paper)
LCC specified in Thin: 13~15 lb (1-1 or 2-1 copy mode only)
LCC specified in Tab paper: 25~45 lb (1-1 or 2-1 copy mode only)
NOTE: Paper type setting for LCC can be made in the Key Operator mode. See p. 13-27 ~ p. 13-28.
Paper Capacity: 4,000 sheets 20 lb/ fixed to standard/wide size 11"x17"/W, F4/W, 8.5"x14"/W,
8.5"x11"/W, 8.5"x11"R/W, A3/W, B4/W, A4/W, or A4R/W
6,600 sheets, including three Main body trays and 100-sheet Multi-Sheet
Bypass Tray
recommended by us.

Paper Information
Paper in Automatic Duplex Unit
Paper Size: STD size: 11"x17"~5.5”x8.5”

STD size (spec.): 11"x17"~A5
Wide paper: 11"x17"W~A5W”
NOTE: 5.5"x8.5"/W and A5/W copy paper is available in crosswise orientation feeding only.
Paper Weight: 16~110 lb (200 g/m2 thick paper)
Paper in Multi-Sheet Bypass Tray
Paper Size: STD size: 11”x17”, 8.5”x14”, 8.5"x11", 8.5”x11”R, 5.5”x8.5”,

5.5”x8.5”R, A3, B4, A4, B5, B5R
STD size (spec.): F4, A4R, A5, A5R, B6R
Non STD size: input the measures of paper between max. 314mm x
459mm and min. 100mm x 148mm
Wide paper: 11”x17”W, 8.5"x11"W, 8.5”x11”WR, 5.5”x8.5”W,
5.5”x8.5”WR, A3W, B4W, A4W, A4WR, B5W, B5WR,
A5W, A5WR
Paper Weight: General mode: 16~24 lb
Thick mode: 25~110 lb (200 g/m2 thick paper)
Thin mode: 13~15 lb
Tab paper mode: 25~45 lb
OHP transparencies, labels, hole punch, rag content can be loaded.
Paper Capacity: 100 sheets 20 lb stacked: single feed special stock
recommended by us.

Paper Information
Paper in 9940/9922 Finisher (Option)
9940/9922 Finisher accepts LEDGER (11"x17"), LEGAL (8.5"x14") and LETTER/R

(8.5"x11"/R) standard/wide paper sizes (5.5"x8.5"R/W in Non-sort, Sort or Group mode).
9940/9922 Finisher Primary (Main) Tray
9940/9922 Finisher (capacities at 20lb, unless otherwise indicated)

Non-sort/Sort/Group mode:
500 sheets 5.5"x8.5"/5.5"x8.5"W, 5.5"x8.5"R/5.5"x8.5"WR (A5/A5W, A5R/A5WR)
3,000 sheets 8.5"x11"/8.5"x11"W, 8.5"x11"R/8.5"x11"WR (A4/A4W, A4R/A4WR,
B5/B5W, B5R/B5WR) (using FS-110 Finisher)
2,500 sheets 8.5"x11"/8.5"x11"W, 8.5"x11"R/8.5"x11"WR (A4/A4W, A4R/A4WR,
B5/B5W, B5R/B5WR) (using FS-210 Finisher)
1,500 sheets 11"x17"/11"x17"W, 8.5"x14" (A3/A3W, B4/B4W)
Staple-sort mode:
1,000 sheets* 11"x17"/11"x17"W, 8.5"x14", 8.5"x11"/8.5"x11"W, 8.5"x11"R/
8.5"x11"WR
*Variable according to the number of pages to be stapled. See the table below.
Paper Capacity for Staple-sort mode of 9940/9922 Finisher
(for the same size only)
8.5”x14”, 8.5”x11”/8.5”x11”W,
11’”x17”/11”x17”W (A3/A3W) 8.5”x11”R/8.5”x11”WR (B4/B4R,
A4/A4W, A4R/A4WR, B5/B5W, A5/A5W)
No. of copies 2 staples 1 staples 2 staples 1 staples
2~9 50 sets 50 sets 100 sets 100 sets
10~20 50 50 50 50
21~30 30 30 30 30
31~40 25 25 25 25
41~50 20 20 20 20
Your service representative can set the copier to stop copying when the number of
copies exceeds above capacity.
Contact your service representative.

Paper Information
Paper in 9940/9922 Finisher (Option) (continued)
9940/9922 Finisher Secondary (Sub) Tray
9940/9922 Finisher (capacities at 20lb, unless otherwise indicated)

200 sheets; max. 12.36"x18.08" (314mmx459mm) ~ min. 3.94"x5.83" (100mmx148mm)
CAUTION:
When the finisher capacity is exceeded due to the print quantity selected, remove the copied sets while
the paper is exiting; otherwise mishandled paper will occur.
9922 Finisher Booklet Tray
Folding mode:
Standard Paper Size : 11"x17", 8.5"x14", 8.5"x11"R, A3, B4, A4R
Wide Paper Size : 11"x17"W, 8.5"x11"WR, A3W, B4W, A4WR
Paper Weight : 16 ~ 110 lb (200 g/m2 thick paper)
Number of Folded Sheets : 3 sheets max.
Booklet Tray Capacity : Approx. 100 sheets max. (11"x17", 8.5"x14", A3, B4)
33 sets max. of 3-sheet-folded booklet
(33 x 3 = 99 sheets)
(50 x 2 = 100 sheets)
Approx. 75 sheets max. (8.5"x11"R, A4R)
(25 x 3 = 75 sheets)
(37 x 2 = 74 sheets)
Stapling & Folding mode:

Standard Paper Size : 11"x17", 8.5"x14", 8.5"x11"R, A3, B4, A4R
Wide Paper Size : 11"x17"W, 8.5"x11"WR, A3W, B4W, A4WR
Paper Weight : 16 ~ 110 lb (200 g/m2 thick paper)
Number of Folded Sheets : 20 sheets max. (using 20lb paper only)
19 sheets max. (a thick cover paper included)

Paper Information
Paper in 9940/9922 Finisher (Option) (continued)
9940 Finisher Booklet Tray (continued)
Booklet Tray Capacity : Approx. 100 sheets max. (11"x17", 8.5"x14", A3, B4)
(20 x 5 = 100 sheets)
(10 x 10 = 100 sheets)
(5 x 20 = 100 sheets)
(15 x 5 = 75 sheets)
(7 x 10 = 70 sheets)
(3 x 20 = 60 sheets)
Three-folding mode:
Paper Size : 8.5"x11", A4
Paper Weight : 20 lb
Number of Folded Sheets : 3 sheets max.
Booklet Tray Capacity Approx. 50 sheets max. (when folding one sheet in three)
CAUTION:
Inside the Booklet mode outlet is the roller drive unit. DO NOT put your hand into the roller drive unit when
removing folded or stapled & folded sheets; otherwise you may be injured.
Paper in 9924 Cover Inserter (Option)

Paper Size: Upper tray: 8.5"x11", 8.5”x11”R, 5.5”x8.5”, A4, A4R, B5, B5R, A5
Lower tray: max. 12.4” x 18.1” (314mm x 459mm)
NOTE: 5.5"x8.5"/W and A5/W copy paper is available in crosswise orientation feeding only.
Paper Weight: 13 ~ 110 lb (200 g/m2 thick paper)

Manual stapling: 13~110 lb (200 g/m2 thick paper)
Manual punching: 13~45 lb
Manual stapling & folding: 16~110 lb (200 g/m2 thick paper)
Manual three-folding: 16~110 lb (200 g/m2 thick paper)
NOTES: • Some 45 lb paper types may not be punched easily
• Punching special paper (self-adhesive sheets etc.) will cause machine trouble.

Paper Information
Paper in Punch Kit (Option)
Paper Size : 11"x17", 8.5"x11"

Paper Weight : 13 ~ 45 lb*
Number of Punch Holes : 3
Hole Diameter : 0.315" ± 0.020" (8.0 mm ± 0.5 mm)
Hole Pitch : 4.253" ± 0.020" (108 mm ± 0.5 mm)
*Some 45 lb paper types may not be punched easily.
NOTE: Special paper (OHP film, labels, tabbed sheets) cannot be punched. Using special paper will cause
machine trouble.
Paper Weight Compatibility Chart

EDH 13 ~ 34 lb
Main Body Trays All Trays: 16 ~ 24 lb
Tray specified in Thick: 25 ~ 110 lb (200g/m2 thick
paper)
Tray specified in Thin: 13 ~ 15 lb
Tray specified in Tab paper: 25 ~ 45 lb (1-1 or 2-1
copy mode only)
Large Capacity Cassette 16 ~ 24 lb
LCC specified in Thick: 25 ~ 110 lb (200g/m2
thick paper)
LCC specified in Thin: 13 ~ 15 lb
LCC specified in Tab paper: 25 ~ 45 lb (1-1 or 2-1
copy mode only)
Automatic Duplex Unit 16 ~ 110 lb (200g/m2 thick paper)
Multi-Sheet Bypass Tray 13 ~ 110 lb (200g/m2 thick paper)
9940/9922 Finisher 13 ~ 110 lb (200g/m2 thick paper)
9924 Cover Inserter 13 ~ 110 lb (200g/m2 thick paper)
Punch Kit 13 ~ 45 lb*
*Some 45 lb paper types may not be punched easily.
recommended by us.

DL650us05v1.fm 1 ページ２００１年１１月１４日　水曜日　午後２時５６分
Section 5: Copier Management
Energy Saver Mode

Auto Low Power
Manual Low Power
Auto Shut-Off
Manual Shut-Off
Entering an ECM Password

Weekly Timer Function
Timer Interrupt
Counter List
To Display Counter List
To Print Counter List
Machine Condition Information
Copier Management 5-1

Copier Management
Energy Saver Mode
There are two modes for the Energy Saver, described below.
Low Power mode enables you to conserve energy by maintaining a lower fixing
temperature during periods of copier inactivity.
Shut-Off mode conserves even more energy by partially turning OFF the power supply.
Auto Low Power
This function automatically lowers the power after a specified period of copier inactivity.
The Auto Low Power function can be set to 5 minutes/ 10 minutes/ 15 minutes/ 30 minutes/
60 minutes/ 90 minutes/ 120 minutes/ 240 minutes. Initially, the mode is set to function
after 15 minutes of copier inactivity. For the Key Operator setting, see p. 13-42.
The [Energy Saver] LED goes on.
Basic Screen
Release Auto Low Power

Press any key on the control panel. The Auto Low Power will be released and the LCD
screen recovers its usual brightness.
5-2 Copier Management

Copier Management
Energy Saver Mode (continued)
Manual Low Power
Press [Energy Saver]. The Low Power Setting Screen will be displayed. Touch YES to
activate the Low Power mode.
NOTE: The Manual Low Power setting can be selected by Key Operator. For the Key Operator setting, see p. 13-
43 to p. 13-49. When selecting the Manual Low Power setting, the Manual Shut-Off setting is released.
When Manual Low Power is on, the following message will be displayed on the dimmed
Basic Screen.
The [Energy Saver] LED goes on.
Low Power Setting Screen Basic Screen
Release Manual Low Power

Press any key on the control panel. The Auto Low Power will be released and the LCD
screen recovers its usual brightness.

Copier Management
Energy Saver Mode (continued)
Auto Shut-Off
This function automatically shuts off the main power after a specified period of copier
inactivity.
The Auto Shut-Off can be set for 30 minutes/ 60 minutes/ 90 minutes/ 120 minutes/ 240
minutes. Initially, Auto Shut-Off is set to function after 90 minutes of copier inactivity. For
the Key Operator setting, see p. 13-42.
Release Auto Shut-Off

Press [Energy Saver]. The copier will become available.
Manual Shut-Off
Press [Energy Saver]. The Shut-Off Setting Screen will be displayed. Touch YES to activate
the Manual Shut-Off mode.
NOTE: The Manual Shut-Off setting can be selected by Key Operator. For the Key Operator setting, see p. 13-43
to p. 13-49. When selecting the Manual Shut-Off setting, the Manual Low Power setting is released.
The [Energy Saver] LED will light and all other LEDs and the LCD screen will be turned off.
Shut-Off Setting Screen
Release Manual Shut-Off

Press [Energy Saver]. The Manual Shut-Off will be released, with the [Energy Saver] LED
turned off and the LCD screen displayed.

Copier Management
Entering an ECM Password
An ECM password is required only when the Electronic Copy Monitor (ECM) feature is
activated, a User Password is assigned, and “Enter E.C.M. password” is displayed on the
touch screen.
1 Enter your 8-digit ECM password, using the keypad.

If the ECM password is invalid, the copier will reset to the Initial mode.
In that case, enter the correct password or contact the Key Operator.
2 Press [Start] once to display your current copy count and copy limit for 3 sec.
Current count / limit

018888/025000
Ready to copy
When your copy count reaches the copy limit, the following message is displayed:
Copy limit reached

025001/025000
In that case, contact the Key Operator to reset your copy limit.
3 Make copying selections, and enter print quantity, as required.
4 When all settings are acceptable, press [Start].
NOTE: To restore the initial state, press [C] while pressing [Utility] when the copy cycle is completed. The
message “Enter E.C.M. password” is displayed on the screen.

Copier Management
Weekly Timer Function
When a copier is using the Weekly Timer function, the Timer indicator on the right side of
the control panel is lit.
Important: When the Timer indicator is lit, the copier will automatically be turned off. Do not
turn it off by pressing power switch.
Timer Interrupt
When the Timer indicator light is on and other indicators are off, the copier is unavailable
due to the Weekly Timer function.
However, the copier will become available if you perform the following procedure.
Print Copy Scan
Energy Saver
Timer
Interrupt
Start
Stop
Panel Reset
1 Press [Energy Saver].

The Basic Screen will be displayed along with the messages shown below.
Please wait
Copier is warming up
Timer interrupt mode

Enter password
NOTE: The Timer Interrupt password is not factory set and must be entered by the Key Operator (see p. 13-39
in “Section 13: Key Operator Mode”). In the event the Timer Interrupt password has not been entered by
the Key Operator, the message shown in Step 3 will display instead.

Copier Management
Weekly Timer Function (continued)
Timer Interrupt (continued)
2 Enter a 4-digit number Timer Interrupt password using the keypad on the control panel.
If an invalid password is entered, enter a valid 4-digit password.
Timer interrupt mode
Enter password ✻✻✻✻
3 Press [Start].
Input copy time
0 hour(s) 05 minute(s)
4 Enter a 1-digit hour (ex. 3 hour is 3) using the keypad on the control panel. (0 ~ 9)
5 Press [Start].
Input copy time is
6 Enter a 2-digit minutes (ex. 7 minutes is 07) using the keypad on the control panel. (05 ~
60)
Input copy time is
7 Press [Start].
Copying is available until the set time is up.
Align original on EDH unit
8 When your copying operation is completed, press [Energy Saver].

The Shut-Off Setting Screen will be displayed.
Shut-Off Setting Screen
9 Touch YES. The copier returns to the OFF state and copying is disabled.

Copier Management
Counter List
This function allows you to view the current indication of the following items as a list on the
touch panel: Total counter, Copier counter, Printer counter, Counter start date. Check the
list, then print it from the Counter List Screen, if desired.
Control Panel Counter List Screen

Help
Program Memory
Mode Check
Utility
Start
Proof Copy
To Display the Counter List
1 Press [Utility] to display the Counter List Screen.

2 Touch EXIT to return to the Basic Screen.
To Print the Counter List

2 Touch Counter list output. The Basic Screen will be displayed.
3 Touch the desired tray key to select the copy size.
4 Press [Start]. The Counter list will be printed out, and the Management list mode will be
released.

Copier Management
Machine Condition Information
When the machine requires troubleshooting or maintenance such as paper/toner supply,

the current machine status can be reported to a network PC by a mail.
Information Items:
• Service call
• JAM
• Paper supply
• Toner supply
• PM call
• Complete job
• Non-complete job
• Staple cartridge supply
• Finisher tray full
• Dispose of trash basket
The “E-Mail Transmission Setting” in the Key Operator mode is required to use this
function. See p. 13-11 to p. 13-12.
The WWW Server Function of the Machine

When the machine is connected to PC over a network, the WWW server of the machine
can be activated to give and display the machine status information using the browser of
the client.
1 URL:
http:// (IP address of the machine)
2 Browser:
Internet Explorer 5.0 / Netscape 4.0 or later
3 Information items:
Paper tray configuration, Engine configuration, Option information, etc.
4 To access the WWW server:
Access the URL from the browser.

DL650us061v1.fm 1 ページ２００１年１１月１４日　水曜日　午後２時５７分
Section 6: Basic Operations
How to Make a Basic Copy

The Basic Screen
Setting Job During Warm-up
To Stop Scanning/Printing
Recalling Previous Job Settings
Copy Mode
Copy Mode Using EDH
1s2 Copy Mode Using Platen Glass
Using the Multi-Sheet Bypass Tray
Copy Density
Manual Mode (Lighter, Normal, Darker)
Density Shift
Lens Mode
Selecting a Special Ratio for Non-Standard Paper
Special Ratio Table
Preset and Custom Zoom Ratios
Zoom Mode
Vertical/Horizontal Zoom
Copy Size
Selecting Paper Type/Size for Multi-sheet Bypass Tray
Binding Mode
Reserve
Set Reserve Job
Job Status Screen
Mishandled Paper During the Reserve Setting
When Paper is Depleted for the Job in Progress
Store Mode
Platen Store Mode
EDH Store Mode
Interrupt Mode
Rotation
Rotation and APS
Rotation and AMS
To Release Automatic Rotation
Check Mode and Proof Copy
Help Mode
Basic Operations
How to Make a Basic Copy
The Basic Screen
When power is turned on, the Basic Screen displays after warm-up, when Energy Saver
mode is activated, when ECM password is set, when Key counter is used, or when Panel
Reset mode is manually or automatically restored. All copying selections can be initiated
from the Basic Screen, whether selected with screen keys or conventional keys, such as
Program Memory.
When the Electronic Copy Monitor (ECM) is activated, a valid 8-digit ECM password,
assigned by the Key Operator, must be entered before copying can be performed. See p.
5-5.
All of the settings in the Basic Screen, except Print Quantity, can be changed by the Key
Operator in the Initial Setting Menu Screen.
Rotation/Original direction/HDD icon Status key

Basic Screen
Messages and
Copier Status Count/Set
indicator
Folder keys
Special Original
Output icon key
Application key
Output Mode
keys Rotation Off key
Store key
Notice message Memory
indicator
Basic Mode keys Original count
NOTE: The original count displayed in the center of the notice message area counts the original pages placed in
the EDH as they are scanned. A duplex original as well as a simplex original count as 1.
When scanning from the platen glass, the counter increases by 1 for every image scanned.
The popup menu appears on the Basic Screen to select the basic copying conditions.
NOTE: During the process of successive copying jobs, the message “Warming up” may be displayed in the
message area of the Basic Screen to maintain the copy image quality.

Basic Operations
How to Make a Basic Copy (continued)
The Basic Screen (continued)
1 Position the original document in the EDH or on the platen glass.

2 Press [Start] to start copying with initial settings or make other selections, then press
[Start].
Basic Copy Settings

Copy mode : see p. 6-7 ~ p. 6-10
Using the Multi-sheet bypass tray : see p. 6-11 ~ p. 6-12
Copy density : see p. 6-13 ~ p. 6-15
Lens mode : see p. 6-16 ~ p. 6-22
Copy size : see p. 6-23 ~ p. 6-26
Binding mode : see p. 6-27
Reserve : see p. 6-28 ~ p. 6-34
Other Basic Copying Operations

Store mode
Platen store mode : see p. 6-35 ~ p. 6-36
EDH store mode : see p. 6-37
Interrupt mode : see p. 6-38 ~ p. 6-39
Rotation : see p. 6-40 ~ p. 6-42
Check mode and Proof copy : see p. 6-43 ~ p. 6-45
Help mode : see p. 6-46 ~ p. 6-47
Output Mode : see Section 7.
Special Original Mode : see Section 8.
Application Selections : see Section 9.
Server Function : see Section 11.
NOTE: If the Basic Screen displays ADJUSTMENT MODE in the message area, this means that the machine
was left in the service adjustment mode by a technician. If this occurs, please contact the technician and
request that the mode be turned off; otherwise copying may be adversely affected.

Basic Operations
Setting Job During Warm-up
While the machine is warming up after power is turned on, select copy conditions and start
scanning so that the machine can start printing as soon as the machine becomes
available.
Warm-up Screen Basic Screen (setting job available)
Basic Screen (next reserve job available) Basic Screen (next reserve setting)
1 Turn on the main power and power switches of the machine.

Seven types of Warm-up Screens display on the LCD touch panel in succession for
approx. 6.0 minutes.
2 Touch the LCD panel to change the Warm-up Screen to the Basic Screen. Check that
the message “Ready to copy reserve” is displayed on the Basic Screen.
3 Set the desired copying conditions, and enter the print quantity.
4 Position original(s) FACE UP in the EDH or FACE DOWN on the platen glass.
5 Press [Start]. The original for the job will be scanned.
When scanning is completed, the highlighted FREE JOB folder key will change to
RESERVE JOB, and the next FREE JOB becomes active.
6 If setting more than one reserve job, touch the next FREE JOB to highlight it.
Repeat step 3 to 5. Up to 5 reserve jobs can be prepared.
Copying on the reserve job will start automatically after completing the warm-up.
NOTE: To stop printing, press [Stop]. See p. 6-5 for details.
NOTE: The Job Status Screen allows you to alter the output order of the reserve jobs or to delete the reserve
job. See p. 6-30 ~ p. 6-32.

Basic Operations
To Stop Scanning/Printing
Follow the procedure below to stop scanning or printing.
Control Panel Basic Screen (to stop scanning)
Time
Start
Stop
Basic Screen (to stop printing)
1 Touch to highlight SCAN JOB or PRINT JOB to be suspended.

2 Press [Stop]. The current machine operation of the selected job will be suspended, and
the popup menu will display on the Basic Screen to ask you to continue or cancel the
job.
3 Touch EXIT to cancel the job and delete the data, or CONTINUE to complete the job.

Basic Operations
Recalling Previous Job Settings
Follow the procedure below to copy with a previous job’s settings.

NOTES:1 Only the last-completed output job settings can be recalled as the previous job settings. Non-complete
job or reserve job settings cannot be recalled, even if the setting operations have been made last.
2 The previous job settings can be recalled, even after the machine power is turned off then on.
Job No. Selection Screen)
1 Press [Program Memory] on the control panel to display the Job No. Selection Screen.
2 Touch PRE-JOB RECALL, then touch OK to return to the Basic Screen.
Change the settings recalled on the screen, if desired.
3 When all settings are acceptable, position original(s) in the EDH or on the platen glass,
then press [Start].

Basic Operations
Copy Mode
Copy Mode Specifications:
Incompatible functions
1-1: Folding or Stapling & Folding with Booklet, Chapter, Booklet
1-2: Transparency interleave
2-1: Folding or Stapling & Folding with Booklet, Chapter, Booklet, Repeat, AUTO
layout, Non-image area erase, Server function
2-2: Chapter, Repeat, Transparency interleave, Non-image area erase, Server
function
EDH capacity
1-1, 1-2, 2-2, 2-1: 100 sheets
(copying can be resumed after removing paper from bins)
EDH original size requirements
1-1, 1-2, 2-2, 2-1: 11"x17", 8.5"x14", 8.5"x11", 8.5"x11"R, 5.5"x8.5", A4R
(8.27"x11.69", 210mm x 297mm)
Copy paper weight requirements
20 lb~24 lb (14 lb~19 lb should be tested before it is used)
Copy paper size requirements
1-1, 1-2, 2-2, 2-1: 11"x17", 8.5"x14", 8.5"x11", 8.5"x11"R, 5.5"x8.5", 5.5"x8.5"R
(5.5"x8.5" paper is available in lengthwise type feeding ( ) only.)
Sort mode paper size (machine with 9940/9922 Finisher)
11"x17", 8.5"x14", 8.5"x11", 8.5"x11"R, 5.5"x8.5", 5.5"x8.5"R, A4R (8.27"x11.69",
210mm x 297mm)
Staple-Sort mode paper size (machine with 9940/9922 Finisher)
11"x17", 8.5"x14", 8.5"x11", 8.5"x11"R, 5.5"x8.5", A4R (8.27"x11.69", 210mm x
297mm)
Folding or Stapling&Folding mode paper size (machine with 9922 Finisher)
11"x17", 8.5"x14", 8.5"x11"R, A4R (8.27"x11.69", 210mm x 297mm)
Cover Inserter paper size (9922 Finisher with 9924 Cover Inserter)
11"x17", 8.5"x14", 8.5"x11", 8.5"x11"R, 5.5"x8.5", A4, A4R (8.27" x 11.69",
210mm x 297mm)
Punching mode paper size (9940/9922 Finisher with Punch Kit)
11"x17", 8.5"x11"

Basic Operations
Copy Mode (continued)
Copy Mode Using EDH
Before selecting the Copy Mode shown on the screen below, read specifications on the
previous page and see Section 4 for information on positioning originals.
Basic Screen (with 1s2 mode selected)
1 Touch the desired mode key on the Basic Screen: 1s1, 1s2, 2s1, or 2s2.
A copy mode key will appear dimmed if it is incompatible with other selections made.
NOTE: When selecting 1s2 or 2s2, specify the original direction and the binding mode on the Special
Original Screen and the Output Mode Screen, respectively. See step 1 to 2 on the next page for
details.
2 Position originals FACE UP in the EDH, as required.
To cancel the mode, touch the desired Copy Mode key on the Basic Screen.
NOTE: When the selected print quantity exceeds the Finisher’s maximum capacity, remove the printed sheets

Basic Operations
1s2 Copy Mode Using Platen Glass
When copying in 1-2 mode from the platen glass, use the Platen store mode. Refer to p. 4-
2 for details on positioning originals.
Special Original Screen Output Mode Screen (with Finisher)
Basic Screen (with platen 1s2 mode selected)
1 Touch SPECIAL ORIGINAL on the Basic Screen to display the Special Original Screen,
then touch the desired original direction key to highlight it.
Touch OK to return to the Basic Screen.
2 Touch OUTPUT APPLI. to display the Output Mode Screen, then touch the desired
binding mode key to highlight it.
Touch OK to return to the Basic Screen.
NOTE: Selecting UP BINDING will make copies upside down on the reverse side, while the RIGHT&LEFT
BINDING copies normally.
3 Open the EDH.
Place original FACE DOWN on the platen glass according to the original direction
specified in step 1, then close the EDH.
IMPORTANT: PLACE AND SCAN ORIGINALS IN REGULAR ORDER OF PAGINATION.
4 Touch 1s2.
The STORE key is automatically highlighted on the screen.

Basic Operations
1s2 Copy Mode Using Platen Glass (continued)
5 Make the desired copying selections.

6 Press [Start] to scan the original.
Repeat steps 3 and 6 until all originals are scanned.
Basic Screen (exit Store mode)
7 Touch STORE to exit the store
mode. The STORE key will return to
the normal display.
8 Enter the print quantity using the
keypad. The quantity entered will be
displayed on the upper right
message area of the Basic Screen.
To change the print quantity, press
[C] (Clear) and re-enter the correct quantity.
To delete the scanned data without printing, press [Stop], then touch EXIT on the popup
menu to be sure the data is deleted.
9 Press [Start] to print.
NOTE: When the selected print quantity exceeds the Finisher’s maximum capacity, remove the printed sheets

Basic Operations
Using the Multi-Sheet Bypass Tray
The Multi-sheet bypass tray can be used to stack regular 13 lb~110 lb Bond paper.
❒ Bypass tray paper size: 11"x17"~5.5"x8.5"

❒ Bypass tray paper weight range: 13~110 lb (200g/m2 thick paper)
❒ Bypass tray paper capacity: up to 100 sheets 20 lb
❒ Bypass tray Transparency film capacity: 1 sheet
1 Open the Multi-sheet bypass tray located on the right side of the copier.
When loading 11"x17" or 8.5"x14" paper, withdraw the right edge of the Multi-sheet
bypass tray.
2 Load copy paper, and align the paper guides to the paper size.
Load Transparency film one sheet at a time or stack paper, up to 100 sheets 20 lb Bond.

Basic Operations
Using the Multi-Sheet Bypass Tray (continued)
Load offset tabbed sheets so that the tab extensions are on the right at the rear (not front)
of the tray. The top sheet is designated face up as the first tab of the finished set.
Subsequent offset tab sheets follow in sequence. The tab extension width should be 0.5"
(12.5 mm) or less.
When loading tabbed sheets in the Multi-sheet bypass tray, be sure to specify the paper
type as Tab paper on the Paper Type/Size Setting Screen; otherwise mishandled paper
may occur. See p. 6-24 to p. 6-26.
Example: 3 Tabbed sheets loaded in position for one finished set.

1st TAB
1st TAB Section 1
Rear Section 1
Introduction 2nd TAB
Printed
side 3rd TAB
3rd TAB
Front
ONE FINISHED SET
Example: 9 Tabbed sheets loaded in position for 3 finished sets.

1st TABS 1st TAB 2nd TAB
Rear Section 1
Section 1
Introduction
Section 1
Introduction
Section 1
Introduction
Section 1
Introduction
Section 1
Introduction 2nd TABS
Introduction
Printed
Front side 3rd TABS
3rd TAB
3 FINISHED SETS

Basic Operations
Copy Density
AES operates with the initial settings. It detects the density of the original image and
automatically selects the appropriate exposure for the copy.
Manual Mode (Lighter, Normal, Darker)

Select manual copy density to adjust exposure (density) when originals are too light or too
dark. Manual adjustments can be made in 9 levels simply by touching the lighter arrow
( ), NORMAL, or darker arrow (▼) key to highlight the desired exposure level indicator.
Basic Screen
Light original Normal Dark original

Basic Operations
Copy Density (continued)
Density Shift
Density shift divides each of nine density levels into three levels of lighter and three levels
of darker.
Density shift can be used in 4 Text/Photo Enhance modes: Auto (Text/photo), Text, Photo,
and Increase contrast.
Density shift 0
Density shift 1
Density shift 2
Density shift 3
Density shift 4
Density shift 5
Special Original Screen
1 Touch SPECIAL ORIGINAL to display the Special Original Screen.

2 Select the desired enhance mode.
To select the Auto (Text/Photo) mode, touch AUTO to highlight it, then press [Utility].
The following message will be displayed:
Density Shift (Text/Photo)

2 (0 ~ 5)

Basic Operations
Copy Density (continued)
Density Shift (continued)
To select the Text mode, touch Text to highlight it, then press [Utility].
Density Shift (Text)

2 (0 ~ 5)
To select the Photo mode, touch Photo to highlight it, then press [Utility].
Density Shift (Photo)

2 (0 ~ 5)
To select the Increase contrast mode, touch Increase Contrast to highlight it, then press
[Utility].
Density Shift (Increase contrast)

3 (0 ~ 5)
3 Press any key (from 0 - 5) using the keypad to determine the Density shift.
4 Press [Stop]. Density shift is determined.

DL650us062v1.fm 16 ページ２００１年１１月１４日　水曜日　午後３時０分
Basic Operations
Lens Mode
APS detects the size of originals placed on the EDH or platen glass and automatically
selects and feeds copy paper of the same size, or selects an appropriate size according to
the magnification ratio selected.
If the appropriate copy paper is not loaded in any tray, no copying will be performed, and a
message will prompt you to load the appropriate paper.
❒ Original sizes detected are: 11"x17", 8.5"x14", 8.5"x11", 8.5"x11"R, 5.5"x8.5", 5.5"x8.5"R
Wide paper sizes cannot be detected.
❒ Incompatible: AMS

Basic Operations
Lens Mode (continued)
AMS is one of the initial settings that functions when the EDH is used and Copy Size is
selected manually.
❒ Incompatible: APS, Change magnification, Book Copy, Overlay, Non-Image Area Erase, Repeat,
AUTO Layout, Storing Image in Overlay Memory
An appropriate reduction or enlargement ratio will be selected automatically and applied to

the image on the copy size. AMS automatically calculates and selects the correct ratio.
Wide paper size can be specified when the AMS is in use. In this case, the same
magnification ratio as that of the standard size will be selected automatically.

Basic Operations
Selecting a Special Ratio for Non-Standard Paper
To determine reduction or enlargement ratios when using non-standard paper sizes, refer
to the Special Ratio Table on the next page and follow the procedure below.
ORIGINAL-COPY WIDTH
FIRST, LOCATE THE ORIGINAL WIDTH ON THE HORIZONTAL AXIS.
THEN, LOCATE THE COPY WIDTH ON THE VERTICAL AXIS.
FIND THE RATIO ON THE TABLE WHERE THESE TWO VALUES MEET.
ORIGINAL-COPY LENGTH
FIRST, LOCATE THE ORIGINAL LENGTH ON THE HORIZONTAL AXIS.
THEN, LOCATE THE COPY LENGTH ON THE VERTICAL AXIS.
FIND THE RATIO ON THE TABLE WHERE THESE TWO VALUES MEET.
The ratio you use must fall within the available magnification range of 0.250~4.000. Use
the smaller ratio for reduction and use the larger ratio for enlargement.
Basic Screen with the popup menu for zoom setting
1 First, determine the correct ratio, as described above.

2 Touch ZOOM on the Basic Screen to display the popup menu for setting the zoom ratio.
3 Use the keypad on the popup menu to enter the desired reduction or enlargement ratio
in 3 digits or use arrows to scroll to the desired ratio.
4 When the desired ratio is specified, touch OK to complete the setting.
To cancel the setting, touch ZOOM again, select the desired ratio, then touch OK.
5 Position original(s) FACE DOWN on the platen glass or FACE UP in the EDH, as
required.
6 When all other settings are acceptable, press [Start].

Basic Operations
Special Ratio Table
5 6 7 8 9 10 11 12 13 14 15 16 17
17 3.40 2.83 2.43 2.12 1.88 1.70 1.54 1.42 1.31 1.21 1.13 1.06 1.00 17
3.00 2.54 2.20 1.94 1.74 1.57 1.43 1.32 1.22 1.14 1.06 1.00
16 3.20 2.67 2.28 2.00 1.77 1.60 1.45 1.33 1.23 1.14 1.06 1.00 0.94 16
2.81 2.38 2.06 1.82 1.63 1.47 1.35 1.24 1.15 1.07 1.00 0.94
15 3.00 2.50 2.14 1.87 1.67 1.50 1.36 1.25 1.15 1.07 1.00 0.94 0.88 15
2.64 2.23 1.93 1.70 1.53 1.38 1.26 1.16 1.07 1.00 0.93 0.88
14 2.80 2.33 2.00 1.75 1.55 1.40 1.30 1.17 1.07 1.00 0.93 0.87 0.82 14
2.45 2.07 1.80 1.59 1.42 1.28 1.17 1.08 1.00 0.93 0.87 0.82
13 2.60 2.17 1.86 1.62 1.44 1.30 1.18 1.08 1.00 0.92 0.87 0.81 0.76 13
2.27 1.92 1.67 1.47 1.31 1.19 1.09 1.00 0.92 0.86 0.81 0.76
12 2.40 2.00 1.71 1.50 1.33 1.20 1.09 1.00 0.92 0.86 0.80 0.75 0.70 12
2.09 1.77 1.53 1.35 1.21 1.09 1.00 0.92 0.85 0.79 0.74 0.70
2.20 1.83 1.57 1.37 1.22 1.11 1.00 0.92 0.85 0.78 0.73 0.69 0.65
COPY SIZE
11 11
1.91 1.61 1.40 1.23 1.10 1.00 0.91 0.84 0.78 0.72 0.68 0.64
10 2.00 1.67 1.43 1.25 1.11 1.00 0.91 0.83 0.77 0.71 0.67 0.62 0.59 10
1.73 1.46 1.27 1.12 1.00 0.90 0.83 0.76 0.70 0.65 0.61 0.57
9 1.80 1.50 1.29 1.12 1.00 0.90 0.82 0.75 0.69 0.64 0.60 0.56 0.53 9
1.54 1.30 1.13 1.00 0.89 0.81 0.74 0.68 0.63 0.59 0.55 0.51
8 1.60 1.33 1.14 1.00 0.89 0.80 0.73 0.67 0.61 0.57 0.53 0.50 0.47 8
1.36 1.15 1.00 0.88 0.79 0.71 0.65 0.60 0.55 0.52 0.48 0.45
7 1.40 1.17 1.00 0.87 0.77 0.70 0.64 0.58 0.54 0.50 0.47 0.44 0.41 7
1.18 1.00 0.86 0.76 0.68 0.62 0.56 0.52 0.48 0.45 0.42 0.39
1.20 1.00 0.85 0.75 0.66 0.60 0.54 0.50 0.46 0.43 0.40 0.37 0.35
6 6
1.00 0.84 0.73 0.65 0.58 0.52 0.48 0.44 0.41 0.38 0.35 0.33
1.00 0.83 0.71 0.62 0.55 0.50 0.45 0.42 0.38 0.36 0.33 0.31 0.29
5 5
5 6 7 8 9 10 11 12 13 14 15 16 17
ORIGINAL SIZE

Basic Operations
Preset and Custom Zoom Ratios
Use the Preset and Custom zoom ratios to increase or decrease magnification in fixed
amounts.
If required, the eight initially set Preset ratios shown below can be adjusted in the Key
Operator mode. In addition, three Custom zoom ratios are adjustable by the Key Operator.
All ratios remain effective until they are replaced.
❒ 8 Preset ratios: 0.500, 0.647, 0.733, 0.785, 1.214, 1.294, 1.545, and 2.000
❒ 3 Custom zoom ratios: Programmable by Key Operator and selected from 0.250~4.000
❒ To copy 5.5"x8.5" originals to 5.5"x8.5" copy paper, select 5.5"x8.5" Copy Size, then select 1.000
magnification.
Basic Screen with the popup menu for preset/custom zoom ratio setting
1 Touch RE to display the popup menu for selecting the desired preset/custom zoom ratio.
2 Select the desired magnification. The selected key is highlighted, and the popup menu
fades automatically, and then the selected ratio will be displayed on the Basic Screen.
To cancel the setting, touch RE again, then select the desired ratio.
required.

Basic Operations
Zoom Mode
Use the Zoom mode to reduce or enlarge the copied original image in 0.1% increments.
❒ Zoom range: 0.250~4.000
2 Use the keypad on the popup menu to enter a 3-digit zoom ratio, or use arrows to scroll
to the desired ratio.
3 Touch OK to complete the setting and return to the Basic Screen.
To cancel the setting, touch ZOOM again, select the desired ratio, then touch OK.
required.

Basic Operations
Vertical/Horizontal Zoom
Use the Vertical/Horizontal zoom mode to reduce or enlarge vertical and horizontal
dimensions, independently.
❒ Vertical/Horizontal zoom range: 0.250~4.000
2 Touch Vert to select a vertical ratio.
3 Use the keypad on the popup menu to enter a 3-digit vertical zoom ratio, or use arrows
to scroll to the desired ratio.
4 Touch Horiz to select a horizontal ratio.
5 Use the keypad to enter a 3-digit horizontal zoom ratio, or use arrows to scroll to the
desired ratio.
6 Touch OK to complete the setting.
To cancel the setting, touch ZOOM again to display the popup menu. Specify the desired
ratios, then touch OK.
7 APS is automatically released on the Basic Screen. Touch to select the desired copy
size key.
required.

Basic Operations
Copy Size
The tray selection keys below COPY SIZE are used to select a specific paper tray. When a
specific tray is selected, the APS key will fade and the AMS key will be highlighted. The
copy size may require a ratio adjustment. When using the EDH with Initial settings, a ratio
will be selected automatically.
Tray locations correspond to main body (tray 1, 2, 3), LCC (tray 4), and Multi-sheet bypass
tray. Paper types, such as Thick, Thin, User, Tab paper, Normal, Recycle, Color, Special,
Fine, Seal may be specified on the trays by the Key Operator for information only, but
paper types cannot be detected by the machine.
NOTE: Do not load paper type other than that specified, otherwise machine trouble may be caused.
❒ When a selected tray is empty, an out-of paper icon will flash on the tray key, along with a
message to load paper in the empty tray.
❒ When the Bypass key is touched and highlighted, the PAPER TYPE/SIZE key appears above the
Bypass key. Touch the key to display the Paper Type/Size Setting Screen, then specify the type
and size of the special paper to be loaded on the Multi-sheet bypass tray. See the next page.
❒ Incompatible Basic Copying Conditions with AMS: APS, Change magnification
❒ Incompatible Special Original with AMS: None
❒ Incompatible Applications with AMS: Book Copy, Non-Image Area Erase, Repeat, AUTO Layout,
Overlay, Overlay Memory
Basic Screen Basic Screen
1 Touch the desired tray key. APS will fade, and AMS will be highlighted.
When selecting the Bypass key, see p. 6-24 ~ p. 6-26.
To restore the APS mode, touch APS. AMS will fade, and APS will be highlighted.
required.
3 When all settings are acceptable, press [Start] from the Basic Screen.

Basic Operations
Copy Size (continued)
Selecting Paper Type/Size for Multi-sheet Bypass Tray
1 Open the Multi-sheet bypass tray, and load the copy paper on the tray. See p. 6-11 ~ p.
6-12 for further details.
Basic Screen
2 Touch the Bypass key, then touch PAPER TYPE/SIZE. The Paper Type/Size Selection
Screen will be displayed.
3 Touch the desired key.
Paper Type/Size Selection Screen
• When Thick, Thin, Tab paper, OHP, Trace, or User is highlighted, a print job will
conform to the selected paper type.
If no paper type indication is needed, touch the highlighted key to clear the selection
in the TYPE area.
The selection will be reflected on the Basic Screen when restored.
NOTE:When selecting Tab paper, AMS is automatically selected.

Basic Operations
Selecting Paper Type/Size for Multi-sheet Bypass Tray (continued)

• When STD size (special) is highlighted, the popup menu will appear.
Use arrows to scroll to the desired size. In this case, both the copy size and type
selected will be indicated on the Basic Screen.
• When Non STD size is highlighted, the popup menu will appear.
To set the vertical size, touch the vertical size key to highlight it, then use the keypad
on the popup menu to enter the vertical size, or use arrows to scroll to that number.
To set the horizontal size, touch the horizontal size key to highlight it, then use the
keypad on the popup menu to enter the horizontal size, or use arrows to scroll to that
number.
In this case, the Special indication and paper type selected will be displayed on the
Basic Screen, but the actual size information cannot be displayed.

Basic Operations
Selecting Paper Type/Size for Multi-sheet Bypass Tray (continued)

• When Wide paper is highlighted, the popup menu will appear.

Use arrows to scroll to the desired wide size, then specify the precise dimensions of
paper to be used, following the procedure below.
(1) Touch Input size. The Size Input popup menu will appear.
(2) Touch the vertical size key to highlight it, then use the keypad on the popup menu
to enter the vertical size, or use arrows to scroll to that number.
The entered number should fall within the range from the vertical size of the
standard size corresponding to the selected wide size, to a maximum of 314mm.
(3) Similarly, touch the horizontal size key to highlight it, then use the keypad on the
popup menu to enter the horizontal size, or use arrows to scroll that number.
The entered number should fall within the range from the horizontal size of the
standard size corresponding to the selected wide size, to a maximum of 459mm.
(4) Touch Select size to return to the Select Size popup menu.
Touch Lead edge or Rear edge to select the image starting position.
4 Touch OK to return to the Basic Screen.

Basic Operations
Binding Mode
When copying in 1-2 or 2-2 mode, specify the binding mode on the Output Mode Screen to
obtain the desired copy result.
Right & Left binding: Normal duplex copies
Up binding: Duplex copies arranged upside down on the reverse side
Binding mode Copies
1 3 1 3
2 2
1 1
2 2
3 3
Output Mode Screen (without Finisher) Output Mode Screen (with Finisher)
1 Touch OUTPUT APPLI. to display the Output Mode Screen, then touch to highlight the
desired binding mode key.

Basic Operations
Reserve
Set Reserve Job
The Reserve function allows you to set up a new job while a current (scan/print) job is in
process. When the current job is finished, the Reserve job starts printing immediately.
The FREE JOB key on the screen is touch sensitive and active only when another job is in
progress; otherwise it appears grayed out.
❒ Job settings: Max. 5 (current job plus 4 reserve jobs)

❒ The reserve job is available to be set after the copier starts to scan the current job. When setting
more than one reserve job, the next reserve job setting will be available after the copier starts to
scan for the previous reserve job.
When the current job is under Store mode, Image insert, or Book copy, the reserve job setting will
be available after the copier starts to print the current job.
❒ If certain conditions occur while a reserve job is being set, such as activation of Interrupt mode,
mishandled paper, or depletion of paper, the current printing job will cease and the FREE JOB
indicator on the screen will be replaced by INTERRUPT, JAM or ADD PAPER, as appropriate.
Perform the required measure for the situation at hand.
❒ The order of the reserve jobs can be altered on the Job Status Screen.
❒ The reserve jobs can be deleted on the Job Status Screen.
❒ Incompatible Basic Copy Conditions: Interrupt copying, Scanning in Store mode, Proof copy
❒ Incompatible Special original: None
❒ Incompatible Applications: Storing image in Overlay Memory
Basic Screen: reserve job available Reserve Job Setting Screen

Basic Operations
Reserve (continued)
Set Reserve Job (continued)
1 Touch FREE JOB to display the Reserve Job Setting Screen.

2 Set the desired copying conditions for the reserve job.
When the Reserve Job Setting Screen is displayed, all keys on the LCD and Control
panel will function for the reserve job.
NOTE: When trouble occurs while setting the reserve job, the PRINT or SCAN JOB key changes to JAM/
ADD PAPER key on the Basic Screen. See p. 6-33 to p. 6-34.
3 Position original(s) FACE UP in the EDH or FACE DOWN on the platen glass after
completing scan for the current job.
4 Press [Start]. The original for the reserve job will be scanned.
NOTE: When the message “Please load size ** paper in any tray except tray #” is displayed, load the specified
paper into the appropriate trays.
5 When the scanning for the reserve job is completed, the Basic Screen for the current
printing job is restored.
6 Repeat step 2 to 4 to reserve more than one job.
7 Copying of the reserve job will start automatically after completing the current job.

Basic Operations
Reserve (continued)
Job Status Screen
Touch the STATUS key on the Basic Screen to display the Job Status Screen (see below).
The Job Status Screen allows you to perform the following functions.
• Confirm machine status
• Change order of reserve job
• Delete reserve job
• View previous job list
• View noncomplete job list
To return to the Basic Screen, touch OK on the Job Status Screen.
Basic Screen Job Status Screen
NO. : Displays the number (01-99) for each job assigned to the machine.
MODE: Displays the machine’s current mode of operation. Three modes are listed
below.
COPIER / PRINTER / SCAN
STATUS: Displays the current status of the machine for each job.
[Indication] [Meaning]
READY : Ready to use in each mode
INTERRUPT : Interrupting the previous job
ERROR : Error in each mode
PRINTING : Printing in each mode
NO PAPER : No paper in copy/print mode
STOP : Stop in each mode
RESERVE : Setting reserve job
JAM : Jam in each mode
TOTAL PAGE(s): Displays the number of scanned pages for each job. (0 to 9999)

Basic Operations
Reserve (continued)
Job Status Screen (continued)
PAGE(s) LEFT: Displays the remaining copy count of the job.

0 to 9999 (The number exceeding 9999 will be displayed as 9999↑.)
Copy count = No. of scanned pages x Print quantity
MINUTE(s) TO GO: Displays the time (in minutes) required for completing the job.
Exceeding 999 minutes: 999↑
Shorter than 1 minute: <1
Other: The following message will be displayed on the second bar when the
reserved job does not exist.
RESERVED JOB DOES NOT EXIST
To change the order of reserve jobs

1 Touch the desired reserve job key to highlight it.
2 Touch JOB PRIORITY. The highlighted reserve job is advanced by one in printing order
unless the job preceding the selected one is already in progress.
3 To return to the Basic Screen, touch OK on the Job Status Screen.
To clear reserve jobs

1 Touch the desired reserve job key to
highlight it.
2 Touch JOB CLEAR.
3 The Job Clear Setting Screen will be
displayed. Touch YES. The highlighted
reserve job is cleared.
4 To return to the Basic Screen, touch OK
on the Job Status Screen.
To check user name (not copier information)

1 Touch USER NAME CHECK to display the
User Name Check Screen.
Check the user name indicated on the
right side of the job No. and operation
mode.
2 To return to the Job Status Screen, touch
OK.

Basic Operations
Reserve (continued)
Job Status Screen (continued)
To display previous job list

1 Touch PREVIOUS JOB LIST to display the Previous Job List Screen
Previous Job List Screen.
2 Touch d to scroll to the next page, if
needed. Up to 16 previous jobs (4 pages)
can be displayed. Touch c to return to the
previous page.
OK.
To display noncomplete job list Noncomplete Job List Screen

1 Touch NONCOMPLETE JOB LIST to
display the Noncomplete Job List Screen.
2 Touch d to scroll to the next page, if
needed. Up to 16 noncomplete jobs (4
pages) can be displayed. Touch c to
return to the previous page.
OK.

Basic Operations
Reserve (continued)
Mishandled Paper During the Reserve Setting
If a misfeed occurs with the print/scan job in progress while you are setting a reserve job,
the PRINT/SCAN JOB key on the screen will change to JAM key.
Basic Screen
If originals of the reserve job are already scanned when the misfeed occurs, the reserve
job printing can be performed after the jam is cleared and the cleared job is completed.
1 Touch JAM to display the Jam Position Screen.

2 To view Help Screen instructions, touch GUIDE and remove paper/original.
3 The JAM will change to PRINT JOB or SCAN JOB.
4 Press [Start]. The print/scan job will be reprocessed.
5 Touch FREE JOB to continue setting the reserve job.
If scanning is not completed when the misfeed occurs, but reserve settings have already
been made, the reserve job can be performed after the cleared job is completed. Simply
insert the original document and press [Start].

Basic Operations
Reserve (continued)
When Paper is Depleted for the Job in Progress
If the paper supply for a print job in progress becomes depleted while you are setting a
Reserve job, the PRINT JOB key on the screen will change to ADD PAPER key (blinking).
Basic Screen
In this case, you can still continue the reserve job setting.
1 Touch ADD PAPER to display the Basic Screen for the print job.
2 Confirm the empty tray and supply the paper.
3 Press [Start]. The print job will be reprocessed.
4 Touch FREE JOB to continue setting the reserve job.

DL650us063v1.fm 35 ページ２００１年１１月１４日　水曜日　午後３時１０分
Basic Operations
Store Mode
Store mode allows you to scan multiple originals by touching the STORE key on the Basic
Screen after setting copying conditions, and then outputting the complete set by pressing
[Start].
Platen store mode: scan originals from the platen glass.
EDH store mode: scan originals from the EDH.
Platen Store Mode

Use Platen store mode for originals that cannot be fed through the EDH due to thickness,
size or condition.
When scanning thick originals that require keeping the EDH open, select Non-image area
erase to prevent exposure of the glass area around the border of the original. This feature
ensures a clean copy result and reduces toner consumption. The Non-image area erase
mode automatically releases after the original for which it is selected is scanned.
Additional images may be scanned.
❒ Incompatible Basic Copying Conditions: None
❒ Incompatible Special Originals: None
Basic Screen
1 Open the EDH.

2 Place original FACE DOWN on the platen glass, then close the EDH.
IMPORTANT: PLACE AND SCAN THE ORIGINALS IN REGULAR ORDER OF
PAGINATION.
3 Make the desired copying selections, and select 1-1 or 1-2 copy mode.
4 Touch STORE on the Basic Screen to highlight it.
5 Press [Start] to scan the original.
6 Repeat steps 1, 2 and 5 until all originals are scanned.
7 Touch STORE to exit the Store mode.
Basic Operations
Store Mode (continued)
Platen Store Mode (continued)
8 Enter the print quantity, using the keypad. The entered quantity will be displayed on the
upper right message area of the Basic Screen.
To change the print quantity, press [C] (Clear) and re-enter the correct quantity.
To delete the scanned data without printing, press [Stop], then touch CANCEL on the
popup menu to ensure that you delete the data.
9 Press [Start]. The copier starts the printing job.

Basic Operations
Store Mode (continued)
EDH Store Mode
Use this feature to scan more than 100 originals into memory from the EDH. Use this
function in conjunction with the Reserve function to increase efficiency of the copying job.

❒ Incompatible Applications: Image insert, Book copy, Storing image in Overlay Memory
Basic Screen
1 Touch STORE on the Basic Screen to highlight it.

2 Make the desired copying selections.
3 Position originals FACE UP on EDH.
If the number of originals exceeds 100, divide them into blocks not exceeding 100
sheets and load them from the block with the first page.
4 Enter the print quantity, using the keypad. The entered quantity will be displayed on the
upper right message area of the Basic Screen.
To change the print quantity, press [C] (Clear) and re-enter the correct quantity.
5 Press [Start] to scan the originals.
6 Repeat steps 3 and 5 until all originals are scanned.

Basic Operations
Interrupt Mode
Use the Interrupt mode to interrupt copying in progress to perform a simple job. When
interrupt copying is completed, the settings for the initial job restore automatically and the
Basic Screen displays. Press the [Interrupt] key when the copier is in the following
conditions:
• Continuously printing data stored using Store mode
• Scanning the originals using Store mode
• Scanning the originals using Store mode while printing in Reserve mode
If desired, Key Operator can change the timing to stop current machine operation for
interrupt copying. Note that the compatible copying conditions vary according to the timing
selected. See p. 13-43 ~ p. 13-49.
❒ Incompatible Basic Copying Conditions: Reserve
Control Panel Basic Screen
Print Copy Scan
Energy Saver
Timer
Interrupt
p
Panel Reset
1 To stop the current copying job, press [Interrupt].

For particular jobs in progress, copying will cease only after certain phases of the
immediate operation are completed, as indicated by LED conditions described below.
• Collectively printing data stored in memory
The [Interrupt] LED blinks until one set of the current job is printed. Then the LED
remains steady for the temporary job performed in Interrupt mode.
• Scanning originals into memory
The [Interrupt] LED blinks until scanning is completed for all originals placed in the
EDH. Then, the LED remains steady for the temporary job performed in Interrupt
mode.
• Scanning originals into memory while printing in Reserve mode (see Note 1)
The [Interrupt] LED blinks until the copier completes the current printing job, and
scans all originals placed on the EDH. The LED remains steady for the temporary job
performed in Interrupt mode.
All JOB indicators on the Basic Screen will change to INTERRUPT.
Basic Operations
Interrupt Mode (continued)
2 Remove any document from the platen glass or from the EDH, if present.
3 Place new original(s) on the platen glass or in the EDH.
4 The copying settings in Interrupt mode are as follows.
Copy Mode : 1s1
EDH : ON
AES : ON
Lens Mode : 1:1 (1.000)
APS : ON
Print Quantity : 1
Finisher : Sort mode using Primary (Main) tray
Select other copying features that are compatible with the Interrupt mode, if desired.
5 Press [Start].
6 When Interrupt copying is completed, press [Interrupt] again to return to the settings of
the initial job.
7 Replace the initial original, then press [Start] to resume copying.
NOTES: 1 In Reserve mode, pressing [Interrupt] before the copier finishes scanning originals of the reserve job
will clear the settings selected for reserve job.
2 When [Mode Check] is pressed during Interrupt Copying, the information displayed reflects the initial
copy job settings. Check mode will not display Interrupt copy job information.

Basic Operations
Rotation
This function allows you to utilize APS or AMS and copy the original size documents
described below onto size 8.5"x11" or 5.5"x8.5", irrespective of the copy paper feeding
direction. By default, Rotation requires APS or AMS to function; however, the Key Operator
may set the function to always function or when APS, AMS or reduce functions. See p. 13-
43 to p. 13-49.
❒ Rotation copying uses memory.
❒ Copy size: 8.5"x11", 8.5"x11"R, 5.5"x8.5"R (lengthwise type feeding ( ) only)
❒ Original size: 11"x17", 8.5"x14", 8.5"x11", 8.5"x11"R, 5.5"x8.5", 5.5"x8.5"R
❒ Incompatible Basic Copying Conditions: V/H zoom, Rotation Sort, Rotation Group
❒ Incompatible Applications: Book Copy, Non-Image Area Erase, Repeat except 2/4/8 Repeat,
AUTO Layout, Storing image in Overlay Memory
Rotation and APS

In APS, the copier automatically copies onto the same paper size as the original(s) in 1:1.
For example, when size 8.5"x11" copy paper is loaded in the tray in lengthwise orientation
and the copier detects that the original is placed in crosswise orientation, Rotation and
APS function together to rotate the original image by 90° and output the 8.5"x11" copy to
match the direction of the copy paper.
Original Copy paper Rotation and APS
APS cannot be
used alone.
Similarly, when size 8.5"x11" copy paper is loaded in the tray in crosswise orientation and
the copier detects that the original is placed in lengthwise orientation, Rotation and APS
function together to rotate the original image by 90° and output the 8.5"x11" copy to match
the direction of the copy paper.
Original Copy paper Rotation and APS
APS cannot be
used alone.

Basic Operations
Rotation (continued)
Rotation and AMS
When size 8.5"x11" copy paper is loaded in the tray in lengthwise orientation and the
copier detects that the original is placed in crosswise orientation, Rotation (if required)
rotates the original image by 90° and the copy is made with the appropriate AMS ratio to fit
the crosswise style of the copy paper.
Original Copy paper Rotation and AMS AMS only
Similarly, when size 8.5"x11" copy paper is loaded in the tray in crosswise orientation and
the copier detects that the original is placed in lengthwise orientation, Rotation (if required)
rotates the original image by 90° and the copy is made with the appropriate AMS ratio to fit
the lengthwise style of the copy paper.
Original Copy paper
Rotation and AMS AMS only

Basic Operations
Rotation (continued)
Rotation and AMS (continued)
When the 5.5"x8.5" tray is selected and the copier detects that the original is placed in
crosswise orientation, Rotation rotates the original image by 90° and the copy is made with
the appropriate AMS ratio to fit the crosswise style of the copy paper.
Original Copy paper Rotation and AMS AMS only
To Release Automatic Rotation
The copier is initially set to activate the Rotation function automatically.

To release automatic Rotation:
Basic Screen
Touch ROTATION OFF on the Basic Screen to highlight it. The Rotation icon will go out and
the Rotation function will be canceled.
To resume automatic Rotation:

Touch ROTATION OFF on the Basic Screen to deselect it. The Rotation icon will be
displayed and the Rotation function will be reactivated.

Basic Operations
Check Mode and Proof Copy
Use the Check mode to confirm copying selections before pressing the [Start] key. The
Mode Check Screen allows you not only to view the current settings but to change or
release them directly from the Check mode.
In this mode, use Proof copy to produce a sample of the copied set before copying multiple
copies. This is a convenient and cost effective way of viewing the results of the following
copying selections.
• Copying conditions using Store mode • Booklet
• Sheet/Cover Insertion • Image Insert
• Chapter • Book Copy
• Combination • Program Job
With Proof copy, all originals are scanned into memory, and only one set is output after you
press the [Proof Copy] key on the control panel or touch PROOF COPY key on the Mode
Check Screen. After Proof copy, some copying condition keys may appear dimmed in the
Mode Check Screen. You cannot change or release the copying conditions indicated on
these grayed out lights.
When [Start] key is pressed, the job resumes copying until the job is completed.
❒ All settings made can be viewed in the Mode Check Screen.
❒ Incompatible Copying Conditions with Proof Copy: Group
Control Panel Mode Check Screen
Help
Program Memory
Mode Check
Utility
Proof Copy
1 Press [Mode Check] on the control panel to display the Mode Check Screen.
2 Verify the settings made for the current job.
3 If necessary, press [Proof Copy] on the control panel or touch PROOF COPY on the
Mode Check Screen to output a set of sample copy.
4 Touch EXIT (or press [Mode Check]) to exit from the Mode Check mode and return to the
Basic Screen.
5 Press [Start] when the Basic Screen is displayed.

Basic Operations
Check Mode and Proof Copy (continued)
Change/Release Settings
If you want to change or release any settings, follow the procedure below.
To change the settings:
Mode Check Screen
Basic Screen
1 Touch the desired copying condition key on the Mode Check Screen to highlight it.
NOTES: • Any key that cannot be highlighted indicates that the copying condition cannot be changed from the
Mode Check Screen.
• Although the following application functions can be highlighted, they cannot be changed but only
released by touching RELEASE SETTING: Overlay, Non-image area erase, Reverse image, AUTO
layout, All-Image Area.
2 Touch CHANGE SETTING. The LCD will display the appropriate screen to change the
copying condition selected.
• Selecting a basic copying condition key will display the Basic Screen.
• Selecting Enhance Mode, Special Orig., or Original key will display the Special
Original Screen. (See Section 8.)
• Selecting an application function key will display the Change Application Selection
Screen.
When BOOK MARK has been checked on a subsequent screen, selecting the
application function key will jump to that screen. See p. 9-2 for details.

Basic Operations
Check Mode and Proof Copy (continued)
3 Change the setting as desired, then restore the Check Screen to return to the checking
steps, or to the Basic Screen to start copying.
To release the settings:

Mode Check Screen
1 Touch the desired special original key or application function key on the Mode Check
Screen to highlight it.
2 Touch RELEASE SETTING.
3 Touch YES to cancel the application function, or NO to restore.
When YES is touched, the selected function will be released and the key will disappear
from the Mode Check Screen.

Basic Operations
Help Mode
Use the [Help] key to access information about the current screen mode and to learn about
setting procedures. The [Help] key can be pressed from any screen except Program
Memory and Key Operator Screens.
The Help Screen also includes the Help menu icon in the center. When the HELP MENU
key is touched, the Help Menu Screen displays a list of all of the copier functions. When a
function item is touched, the Help Screen displays information specific to that topic.
The KEY OPERATOR MODE key is also provided in the lower left position of the Help
Screen. When touched, the Key Operator Password Entry Screen will be displayed to
access the Key operator mode. See p. 13-2.
Control panel Weekly timer key

contrast key
Help Screen
Help
Program Memory
Mode Check
Utility
Proof Copy
Help Menu Screen

Basic Operations
Help Mode (continued)
1 While in any screen, press [Help] to display the Help Screen.

2 Touch TONER SUPPLY, PAPER SUPPLY, EDH, STAPLE SUPPLY, PUNCH, FOR
ASSISTANCE, or the Service call telephone number and Fax number to display specific
Help information.
3 For help on operations, touch HELP MENU in the center area of the screen. The Help
Menu Screen will be displayed. Select one of the 7 Help menu items.
4 The Weekly timer key display only when the Weekly timer system is activated. Touch the
key to display the settings of the Weekly timer.
5 Touch EXIT to return to the screen that was displayed before pressing [Help].

DL650us071v1.fm 1 ページ２００１年１１月１４日　水曜日　午後３時１２分
Section 7: Output Modes
9940/9922 Finisher Specifications

Non-Sort Mode Using Primary (Main) Tray
Sort Mode Using Primary (Main) Tray
Staple-Sort Mode Using Primary (Main) Tray
Group Mode Using Primary (Main) Tray
Output Modes Using Secondary (Sub) Tray
Folding and Stapling & Folding Modes
Punching Mode
Three-Folding Mode
9924 Cover Inserter
Manual Finishing
Output Mode for Machine without Finisher
Face Down Exit
Face Up Exit
Output Modes 7-1

Output Modes
9940/9922 Finisher Specifications
Use only paper that is recommended by us and stored under the environmental conditions
stated for copy quality. Special stock is not guaranteed for reliability or copy quality.
This Finisher also accommodates wide paper sizes in addition to the standard sizes
described below. See p. 4-9 ~ p. 4-10.
Finisher Type
❒ Primary (Main) Tray with built-in 2 stapling: moving tray type
Secondary (Sub) Tray
Booklet Tray (9922 Finisher only)
9924 Cover Inserter (option)
Punch Kit (option)
Primary (Main) Tray

• Non-Sort Mode
❒ Paper size: 11"x17"~5.5"x8.5"
❒ Paper weight: 16~24 lb; Special stock (65 lb (176 g/m2 cover paper), transparency film, labels,
hole punch, rag content)
❒ Paper capacity for 20 lb: 500 sheets 5.5"x8.5"
3,000 sheets 8.5"x11", 8.5"x11"R (9940)
2,500 sheets 8.5"x11, 8.5"x11"R (9922)
1,500 sheets 11"x17", 8.5"x14"
• Sort Mode/Group Mode
❒ Paper size: 11"x17"~5.5"x8.5"
❒ Paper weight: 16~24 lb
3,000 sheets 8.5"x11", 8.5"x11"R (9940)
2,500 sheets 8.5"x11, 8.5"x11"R (9922)
1,500 sheets 11"x17", 8.5"x14"
• Staple-Sort Mode
❒ Paper size: 11"x17", 8.5"x14", 8.5"x11"R, 8.5"x11" (5.5"x8.5" is available in crosswise orientation
only.)
❒ Paper capacity for 20 lb: 1,000 sheets*1
❒ Staple capacity: 50 sheets*2 (5.0mm thick or less)
❒ Staple position: See p. 7-8.
NOTES: *1: Variable according to the number of pages to be stapled. See p. 4-9 for details.
*2: Staple sheet capacity is changeable, and may be set to 45, 40 or 35 by your service representative.
7-2 Output Modes

Output Modes
9940/9922 Finisher Specifications (continued)
Secondary (Sub) Tray

• Non-sort and face down exit
• Non-sort and face up exit
• Group and face down exit
• Group and face up exit
❒ Paper size: 11"x17"~5.5"x8.5"
❒ Paper capacity for 20 lb: 200 sheets
Booklet Tray (9922 Finisher only)

• Folding Mode
❒ Paper size: 11"x17", 8.5"x14", 8.5"x11"R, A4R (8.27"x11.69", 210mm x 297mm)
❒ Paper weight: 16~24 lb; Special stock (20 lb paper is recommended)
❒ Number of Folding sheet: 3 sheets max.
❒ Booklet tray capacity: Approx. 100 sheets max.
(33 x 3 = 99 sheets)
(50 x 2 = 100 sheets)
Approx. 75 sheets max. for 8.5"x11"R, A4R
(25 x 3 = 75 sheets)
• Stapling & Folding Mode

❒ Paper size: 11"x17", 8.5"x14", 8.5"x11"R, A4R (8.27"x11.69", 210mm x 297mm)
❒ Number of Folding sheet: 20 sheets max. (using 20 lb paper only)
19 sheets max. (a thick cover paper included)
❒ Booklet tray capacity: Approx. 100 sheets max.
(20 x 5 = 100 sheets)
(10 x 10 = 100 sheets)
(6 x 16 = 96 sheets)
Approx. 75 sheets max.
(15 x 5 = 75 sheets)
Output Modes 7-3

Output Modes
9940/9922 Finisher Specifications (continued)
9924 Cover Inserter

❒ Paper size: Lower tray; 11"x17", 8.5"x14", 8.5"x11", 8.5"x11"R, 5.5"x8.5", A4, A4R (8.27"x11.69",
210mm x 297mm)
Upper tray; 8.5"x11", 8.5"x11"R, 5.5"x8.5
❒ Paper weight in cover sheet mode: 13~110 lb (200g/m2 thick paper)
❒ Paper weight in manual staple: 16~24 lb
Punch Kit
• Punching Mode (available in combination with Primary (Main) Tray output modes)
❒ Paper size: 11"x17", 8.5"x11"
❒ Number of holes: 3 holes
❒ Hole diameter: 0.315" ± 0.020" (8.0 mm ± 0.5 mm)
❒ Hole pitch: 4.252" ± 0.020" (108 mm ± 0.5 mm)
7-4 Output Modes

Output Modes
Non-Sort Mode Using Primary (Main) Tray
The Non-sort mode simply means that the offset-stacker finisher modes are not selected.
Copies will be stacked upon exit without being offset by sorted sets.
With the Primary (main) tray initially selected on the Output Mode Screen, 9940/9922
outputs the printed sheets FACE DOWN in the proper order.
❒ Paper size: 11"x17", 8.5"x14", 8.5"x11"R, 8.5"x11", 5.5"x8.5"

3,000 sheets 8.5"x11", 8.5"x11"R (9940)
2,500 sheets 8.5"x11", 8.5"x11"R (9922)
1,500 sheets 11"x17", 8.5"x14"
Basic Screen
3
2
1
3
2
1
1 Touch SORT on the Basic Screen to deselect it, if highlighted.

2 Enter the desired print quantity.
3 Position original(s) in the EDH or on the platen glass, and make copying selections, as
required.
4 Press [Start] to begin copying in Non-sort mode.
Copies will exit face down, with the page heading toward the front of the copier.
CAUTION:
Output Modes 7-5

Output Modes
Sort Mode Using Primary (Main) Tray
Use this mode when you want to output multiple copies of the original set, and have each
sorted set offset upon exit. The staple mode can be selected with the sort mode.
❒ Paper size: 11"x17", 8.5"x14", 8.5"x11", 8.5"x11"R, 5.5"x8.5", 5.5"x8.5"R

3,000 sheets 8.5"x11", 8.5"x11"R (9940)
2,500 sheets 8.5"x11", 8.5"x11"R (9922)
1,500 sheets 11"x17", 8.5"x14"
Basic Screen
3
2
1
3
2
1
30mm
1 Touch SORT on the Basic Screen to highlight it.

3 Position originals in the EDH, and make copying selections as required.
When using Store mode, see p. 6-35 to p. 6-37.
4 Press [Start].
CAUTION:
7-6 Output Modes

Output Modes
Staple-Sort Mode Using Primary (Main) Tray
Use this mode when you want to offset and staple each copied set. Stapling position and
number of staples (1 or 2) can be designated on the Output Mode Screen.
Each finished set will be offset from the next copied set.
❒ Stapled paper at 1 position: 11"x17", 8.5"x14", 8.5"x11"R, 8.5"x11" (5.5"x8.5" is available in

crosswise orientation only.)
❒ Stapled paper at 2 positions: only 8.5"x11" paper loaded with larger vertical dimension
11"x17", 8.5"x14", 8.5"x11"R, 8.5"x11" paper loaded with larger
horizontal dimension
❒ Paper capacity for 20 lb: 1,000 sheets (Variable according to the number of pages to be stapled.
See p. 4-9 for details.)
❒ Staple capacity: 50 sheets 20 lb (5.0mm thick or less)
(Staple capacity is changeable, and may be set to 45, 40, or 35 by service.)
❒ Staple position: 1 oblique staple*; 2 parallel staples
*: Oblique staple may change to parallel staple when using some copy sizes.
❒ Incompatible Copy Conditions: Using platen glass (available when using Image Insert, Book
Copy, Platen Store Mode), Folding / Stapling & Folding / Three-Folding, Transparency Interleaving
Basic Screen 3 3
2 2
3 3
2
1 1
3 3
2 2
1 1
1 oblique staple 2 parallel staples
Output Modes 7-7

Output Modes
Staple-Sort Mode Using Primary (Main) Tray (continued)
1 Touch STAPLE SORT on the Basic Screen to highlight it. The Staple Position icon will be
displayed in the OUTPUT icon area. When not changing the staple position, proceed to
step 7.
Basic Screen Output Mode Screen
Staple position Binding mode
1 3 3 1 1 3
2 2 2
1 1 1
2 2 2
3 3 3
2 Touch OUTPUT APPLI. on the Basic Screen to display the Output Mode Screen.
3 Touch the desired key among the four keys on the screen to select the staple position.
When making double-sided copies, also touch to highlight the desired binding mode key,
referring to the above illustration.
4 Touch OK on the Output Mode Screen to complete the setting and return to the Basic
Screen.
The selection made in stapling position will be displayed in the OUTPUT icon area.
5 Touch SPECIAL ORIGINAL on the Basic Screen to display the Special Original Screen.
6 Touch to select the desired original set direction, then touch OK to return to the Basic
Screen.
7-8 Output Modes

Output Modes
Staple-Sort Mode Using Primary (Main) Tray (continued)
7 Select additional copying features, as required.

9 Position originals in the EDH. When using Store mode, see p. 6-35 to p. 6-37.
10 Press [Start].
CAUTION:
Output Modes 7-9

Output Modes
Group Mode Using Primary (Main) Tray
Use this mode when you want to group together multiple copies of each original, and offset
the sets upon exit. Grouped sets cannot be stapled.
❒ Paper size:11"x17", 8.5"x14", 8.5"x11", 8.5"x11"R, 5.5"x8.5", 5.5"x8.5"R
3,000 sheets 8.5"x11"R, 8.5"x11" (9940)
2,500 sheets 8.5"x11"R, 8.5"x11" (9922)
1,500 sheets 11"x17", 8.5"x14"
Basic Screen 3
3
2
2
1
1
30mm
2 Touch GROUP, then OK to complete the setting and return to the Basic Screen.
The GROUP icon will be displayed in the OUTPUT icon area.
5 Press [Start].
CAUTION:
7-10 Output Modes

Output Modes
Output Modes Using Secondary (Sub) Tray

In addition to the Primary (main) tray, 9940/9922 Finisher is equipped with a Secondary
(sub) tray that can be selected on the Output Mode Screen.
The Secondary (sub) tray provides 4 types of output mode as specified below, also to be
specified on the Output Mode Screen.
(1) Face down non-sort exit (3) Face down group exit
(2) Face up non-sort exit (4) Face up group exit
❒ Paper size: 11"x17"~5.5"x8.5"
❒ Paper capacity for 20 lb: 200 sheets
Non sort + Face down Output Mode Screen
Non sort + Face up Output Mode Screen
Group + Face down Output Mode Screen
Output Modes 7-11

Output Modes
Output Modes Using Secondary (Sub) Tray (continued)

Group + Face up Output Mode Screen
2 Touch SUB TRAY to display the popup menu OUTPUT<SUB TRAY>.
3 Touch the desired key(s) on the popup menu to specify one of the four output modes. To
select Non-sort and face down exit, touch FACE DOWN.
To select Non-sort and face up exit, touch FACE UP.
To select Group and face down exit, touch GROUP and FACE DOWN.
To select Group and face up exit, touch GROUP and FACE UP.
Screen.
The selection made in output mode using secondary (sub) tray will be reflected in the
OUTPUT icon area of the Basic Screen.
7 Press [Start].
CAUTION:
7-12 Output Modes

Output Modes
Folding and Stapling & Folding Modes
The Folding and Stapling & Folding modes are available only when the 9922 Finisher
option is installed. When any mode is selected, the Booklet feature is automatically
selected and indicated on the Application Selection Screen.
NOTES: 1. When copying two-sided signature originals using the Folding or Stapling & Folding mode, release
the automatically selected Booklet mode on the Application Selection Screen.
2. When copying dark originals or using Reverse Image mode together with Folding or Stapling & Fold-
ing mode, the folded line of the output copies may be slightly shifted.
The following copy results may be expected when using Folding or Stapling & Folding
mode:
In the Folding mode, each copied set is folded and output to the Booklet tray of the
Finisher.
In the Stapling & Folding mode, each copied set is stapled at two positions (saddle
stitched), then folded and output to the Booklet tray of the Finisher.
❒ Use EDH.
❒ Max. number of folded sheets (20 lb Bond) in both modes:
Folding: 3 sheets (less than in Staple & Folding mode because they are not cinched first)
Stapling & Folding: 20 sheets
19 sheets when using thick cover paper
❒ Paper size: 11"x17", 8.5"x14", 8.5"x11"R, A4R
❒ Booklet tray capacity:
When the Booklet tray capacity is exceeded, the finisher will stop operating. Select the
appropriate print quantity by referring to the following capacities.
Approx. 100 sheets max.
Folding: 33 sets max. of 3-sheet-folded booklet (33 x 3 = 99 sheets)
Stapling & Folding: 20 sets max. of 5-sheet-folded booklet (20 x 5 = 100 sheets)
6 sets max. of 15-sheet-folded booklet (6 x 15 = 90 sheets)
Folding: 25 sets max. of 3-sheet-folded booklet (25 x 3 = 75 sheets)
Stapling & Folding: 15 sets max. of 5-sheet-folded booklet (15 x 5 = 75 sheets)
❒ Incompatible Basic Copying Conditions with Booklet selected: APS, 1-1, 2-1, Rotation, Sort,
Staple-sort, Group, Cover sheet feeding, Three-Folding, Rotation Sort, Rotation Group, Punching
❒ Incompatible Special Originals with Booklet selected: Mixed Original, Whole Area in Non STD
size, Tab Paper
❒ Incompatible Applications with Booklet selected: Sheet/Cover Insertion, Combination,
Transparency Interleave, Program Job, Non-Image Area Erase, Reverse Image, Repeat
❒ Incompatible conditions without Booklet: Sort, Staple-sort, Group, Rotation Sort, Rotation Group,
Three-Folding, Punching, Transparency Interleave, Reverse Image
Output Modes 7-13

Output Modes
Folding and Stapling & Folding Modes (continued)
Folding Stapling & Folding
3 sheets max. 20 sheets max.

19 sheets max. when using thick cover paper
Folding Output Mode Screen
Stapling & Folding Output Mode Screen
7-14 Output Modes

Output Modes
Folding and Stapling & Folding Modes (continued)
1 Close the EDH securely, then press [Panel Reset].

3 Touch STAPLING & FOLDING or FOLDING, as desired.
NOTE: Selecting FOLDING or STAPLING & FOLDING will automatically switch the output tray to Booklet
tray. Notice that the arrow pointing to the MAIN TRAY shifts to the Booklet tray.
4 Touch OK on the Output Mode Screen. The Basic Screen will be restored and the
selection made in the output mode will be reflected in the OUTPUT icon area.
NO COVER SHEET of Booklet is automatically selected. To change this selection, touch
APPLI. on the Basic Screen to display the Application Selection Screen, then touch
Booklet twice to display the Booklet Mode Selection Screen to make another selection
or to release the setting.
NOTE: When loading originals, heed the following limits on capacity:
Folding mode:
12 pages or less for simplex copying
6 pages or less for duplex copying
Stapling & Folding mode:
80 pages or less for simplex copying
40 pages or less for duplex copying
Exceeding the above capacity limits may cause trouble in the finisher.
8 Press [Start].
CAUTION
When the Booklet tray capacity is exceeded, the finisher will cease operating. To avoid this, select the
appropriate print quantity from the specifications shown on p. 7-13.
Output Modes 7-15

Output Modes
Punching Mode
The Punching mode is available only when the Punch Kit option is installed on the 9940/
9922 Finisher.
When the Punching mode is selected in combination with any of the Primary (Main) tray
output modes, each copied sheet is punched and output to the Primary tray according to
the selected output mode.
NOTE: Some staple positions previously selected may conflict with this function.
❒ Copy paper size: 11"x17", 8.5"x11" (20 lb paper recommended)

❒ Paper weight: 20 lb ~ 24 lb bond recommended
Thin paper: 16 lb ~ 19 lb
Thick paper: 25 lb ~ 45 lb
❒ Number of holes: 3 holes
❒ Hole diameter: 0.315" ± 0.020" (8 mm ± 0.5 mm)
❒ Hole pitch: 4.252" ± 0.020" (108 mm ± 0.5 mm)
❒ Incompatible Basic Copying Conditions: Using platen glass (available when using Platen store
mode), Folding, Stapling & Folding, Three-Folding, Output modes using secondary tray, Cover
Sheet mode
❒ Incompatible Special Originals: Mixed Original with APS mode and/or 8.5"x11"R, 5.5"x8.5"
mixed, Non STD Size
❒ Incompatible Applications: Sheet/Cover Insertion, Copy insertion mode in Chapter, Cover sheet
mode in Booklet, Transparency Interleave, Program Job
Basic Screen
4.252"
(108mm)
Output Mode Screen
7-16 Output Modes

Output Modes
Punching Mode (continued)

Punch Position Selection Screen
2 Touch PUNCH to display the Punch Position Selection Screen.
3 Touch the desired punch position key on the screen to highlight it.
4 Touch OK on the Punch Position Selection Screen to restore the Output Mode Screen.
Screen.
The selection made in punching position will be displayed in the OUTPUT icon area.
7 Touch to select the desired original set direction, then touch OK to return to the Basic
Screen.
11 Press [Start].
CAUTION:
Output Modes 7-17

Output Modes
Three-Folding Mode
The Three-Folding mode is available only when the 9922 Finisher option is installed.
In this mode, the original image is copied on 8.5"x11"R copy paper and output to the
Booklet tray of the Finisher.
❒ Copy paper size: 8.5"x11"R, A4R (20 lb paper recommended)
❒ Max. number of folded sheets (20 lb Bond): 3 sheets
❒ Booklet tray capacity: 50 sets max. of 1-sheet-folded set (50 sheets)
❒ Incompatible Basic Copying Conditions: Sort, Staple-sort, Group, Output modes using secondary
tray, Folding, Stapling & Folding, Punching
❒ Incompatible Applications: Transparency Interleave, Book Copy, Program Job, Reverse Image
Z
A
Three-Folding copy
7-18 Output Modes

Output Modes
Three-Folding Mode (continued)
1 Load 8.5"x11"R or A4R copy paper in a tray.

3 Touch THREE-FOLDING to highlight it.
Screen.
The THREE-FOLDING icon will be displayed in the OUTPUT icon area.
5 Select additional copying features, as required. Touch to highlight the 8.5"x11"R or A4R
tray key, if not already highlighted.
NOTE: Up to 3 originals can be three-folded.
8 Press [Start].
CAUTION:
appropriate print quantity from the specifications shown on p. 7-18.
Output Modes 7-19

Output Modes
9924 Cover Inserter
The 9924 Cover Inserter is available as an option on the 9940/9922 Finisher.

Load cover sheet paper into this device and use the sheets as front covers for copied sets
output to the Main tray or use the sheets as booklet-type covers for copied sets output to
the Booklet tray in the Folding or Stapling & Folding mode.
NOTES:
• Paper loaded into the cover inserter cannot be copied.
• This function is incompatible with cover sheet mode (COVER WITH COPY SHEET and COVER WITH BLANK
SHEET) in Booklet and cover mode in Sheet/Cover Insertion.
❒ Cover paper size:

Upper tray; 8.5"x11", 8.5"x11"R, 5.5"x8.5"*
Lower tray; 11"x17", 8.5"x14", 8.5"x11", 8.5"x11"R, 5.5"x8.5" *
*5.5"x8.5" paper is available in crosswise type feeding only.
❒ Cover paper weight: 13~110 lb (200g/m2 cover paper)
❒ Tray capacity: 200 sheets (110 lb (200g/m2 cover paper) or 30mm thick for both trays
❒ Incompatible Basic Copying Conditions: Output to Secondary (sub) tray, Punching
❒ Incompatible Applications: Cover mode in Sheet/Cover Insertion, Cover sheet mode in Booklet,
Transparency Interleave
Cover sheet
Copied set with

cover attached
Copied sets with cover

attached in Folding or
Stapling & Folding mode
7-20 Output Modes

Output Modes
9924 Cover Inserter (continued)

Cover Sheet Insert Selection Screen
1 Close the EDH securely, then press [Panel Reset].

3 Touch COVER SHEET to display the Cover Sheet Insert Selection Screen.
4 Touch FRONT, FRONT+BACK, or BACK to highlight it, then select the covers tray.
When selecting FRONT+BACK mode, different tray source can be specified for each.
NOTE: Copy paper sizes available to be loaded are different in each tray. See the specification on p. 7-20.
Touch OK to restore the Output Mode Screen.
5 Touch OK on the Output Mode Screen. The Basic Screen will be restored.
7 Load the cover sheet paper into the optional 9924
Cover Inserter of the 9940/9922 Finisher. Upper tray
If the paper size loaded in the 9924 Cover Inserter Lower
is not suitable, the following messages will be tray
displayed and copying will be unavailable.
Please load cover sheet in
cover inserter
Adapt paper size between
cover sheet and selected paper
Output Modes 7-21
Output Modes
9924 Cover Inserter (continued)

9 Position originals in the EDH or on the platen glass.
10 Press [Start].
CAUTION:
7-22 Output Modes

Output Modes
Manual Finishing
The Manual Finishing function is available only with the 9924 Cover Inserter option
installed on the 9940/9922 Finisher. To use this convenient function, simply place a set of
paper into the lower tray of the 9924 Cover Inserter, select the desired mode from the
Manual Finishing operation panel located on the top of the Finisher, then press the Start/
Stop button.
Available finishing modes according to the optional configuration are described below.
9940 Finisher + 9924 Cover Inserter
• 1 oblique staple: Primary (main) tray
• 2 parallel staples: Primary (main) tray
9940 Finisher + 9924 Cover Inserter + Punch Kit
• 1 oblique staple
• 2 parallel staples
• Punching
9922 Finisher + 9924 Cover Inserter
• Stapling & Folding (2 staples in the center + Folding)
• Three-Folding
9922 Finisher + 9924 Cover Inserter + Punch Kit
• Stapling & Folding (2 staples in the center + Folding)
• Three-Folding
• Punching
Specifications for Manual Stapling 1 oblique staple and 2 parallel staples
❒ Paper size: 11"x17", 8.5"x14", 8.5"x11", 8.5"x11"R, 5.5"x8.5", A4, A4R (8.27"x11.69", 210mm x
297mm)
❒ Paper weight: 16~24 lb (20 lb paper is recommended)
❒ Staple capacity: 50 sheets max. (20 lb paper)
❒ Output tray: Primary (main) tray
Specifications for Manual Punching

❒ Paper size: 11"x17", 8.5"x11", A4 (8.27"x11.69", 210mm x 297mm)
❒ Punch capacity: 200 sheets max. (24 lb paper) or within 30mm thick
❒ Output tray: Primary (main) tray
Output Modes 7-23

Output Modes
Manual Finishing (continued)
Specifications for Manual Stapling & Folding mode

❒ Paper size: 11"x17", 8.5"x14", 8.5"x11"R, A4, A4R (8.27"x11.69", 210mm x 297mm)
❒ Staple capacity: 20 sheets max. (20 lb paper)
19 sheets max. (20 lb paper with a thick paper cover)
❒ Output tray: Booklet tray
Specifications for Three-Folding mode

❒ Paper size: 8.5"x11"R, A4R (8.27"x11.69", 210mm x 297mm)
❒ Folding capacity: 3 sheets max. (20 lb paper)
❒ Output tray: Booklet tray
Start/Stop button
Stapling &
Folding
1 oblique staple
2 parallel staples
Three-Folding Punching
1 Place a set of paper to be finished into the lower

tray of the 9924 Cover Inserter, as described below
Guide plate
for each mode, then align the guide plate. The Lower
indicator light of Start/Stop button will turn green. tray
• 1 oblique staple / 2 parallel staples: FACE UP
• Punching: FACE UP
• Stapling & Folding: FACE UP for the outside of
the finished set
• Three-Folding: FACE UP for the outside of the
folded set
7-24 Output Modes

Output Modes
Manual Finishing (continued)

NOTE: Refer to the specifications on previous page for available paper size and capacity in each mode.
2 Press Staple Mode Selection button and/or Punch button to select the desired mode.
NOTE: Punching mode is compatible with 1 oblique staple, 2 parallel staples, or Stapling & Folding mode.
3 Press Start/Stop button.
Finished sheets will be delivered to the appropriate tray according to the selected mode.
NOTE: If you want to stop the Manual Finishing operation, press the Start/Stop button again. The Finisher will
cease operating. When using Stapling & Folding mode, the unfinished set will be left in the stacker unit
inside the Finisher.
CAUTION
appropriate print quantity from the specifications on p. 7-13.
CAUTION:
Output Modes 7-25

DL650us072v1.fm 26 ページ２００１年１１月１４日　水曜日　午後３時１５分
Output Modes
Output Mode for Machine without Finisher
This section describes eight output modes for a copier without the Finisher.
❒ Face down non-sort exit (default) ❒ Face up non-sort exit
❒ Face down rotation sort exit ❒ Face up rotation sort exit
❒ Face down group exit ❒ Face up group exit
❒ Face down rotation group exit ❒ Face up rotation group exit
Originals
2 3
1 Example:
3-set copies
Face down Face down Face down Face down

non-sort (default) rotation sort group rotation group
Face up Face up Face up Face up

non-sort rotation sort group rotation group
7-26 Output Modes

Output Modes
Output Mode for Machine without Finisher (continued)
Face Down Exit
• Non-sort mode copies the original set in amounts determined by the print quantity
setting, then outputs sorted sets normally.
• Rotation sort mode rotates every other sorted set by 90° upon exit, provided the same
paper size is loaded in two trays, one tray with paper loaded in crosswise orientation and
the other tray with paper loaded in lengthwise orientation.
• Group mode copies each original page in amounts determined by the print quantity
setting, then outputs grouped sets normally.
• Rotation group mode rotates every other grouped set by 90° upon exit, provided the
same paper size is loaded in two trays, one tray with paper loaded in crosswise
orientation and the other tray with paper loaded in lengthwise orientation, e.g., 8.5"x11"
and 8.5"x11"R.
Basic Screen
To Set Face Down Non-Sort Exit

1 Confirm that the OUTPUT APPLI. key is not highlighted.
If OUTPUT APPLI. is highlighted, touch OUTPUT APPLI. to display the Output Mode
Screen. Select to highlight FACE DOWN and deselect all the other keys, then touch OK.
2 Confirm that the SORT key is not highlighted.
If SORT is highlighted, touch SORT to deselect it.
Output Modes 7-27

Output Modes
Face Down Exit (continued)

Basic Screen
To Set Face Down Rotation Sort Exit

1 Confirm that the OUTPUT APPLI. key is not highlighted.
If OUTPUT APPLI. is highlighted, touch OUTPUT APPLI. to display the Output Mode
Screen. Select to highlight FACE DOWN and deselect all the other keys, then touch OK.
2 Touch SORT to highlight it.
To Set Face Down Group Exit

2 Touch GROUP and FACE DOWN to highlight them.
7-28 Output Modes

Output Modes
Face Down Exit (continued)

To Set Face Down Rotation Group Exit

2 Touch ROTATION GROUP and FACE DOWN to highlight them.
Output Modes 7-29

Output Modes
Face Up Exit
Unless Face Up Exit is selected, all simplex copies and odd numbered duplex copies exit
to the tray face down. When Face Up Exit is selected, all simplex copies and odd
numbered duplex copies exit face up. While the Face Up Exit mode reduces the amount of
paper movement, you will be required to arrange pages in the correct order manually.
❒ Face up exit can be selected together with Non-sort, Rotation sort, Group, or Rotation group.
❒ When using the platen glass with simplex (1-1) copying, start copying from the last page first and
continue in that reverse order to output the set in correct order.
❒ Incompatible: None
To Set Face Up Non-Sort Exit

1 Confirm that the SORT key is not highlighted.
If SORT is highlighted, touch SORT to deselect it.
2 Touch OUTPUT APPLI. to display the Output Mode Screen.
3 Touch FACE UP to highlight it.
7-30 Output Modes

Output Modes
Face Up Exit (continued)

To Set Face Up Rotation Sort Exit

2 Touch FACE UP to highlight it.
4 Touch SORT to highlight it.
To Set Face Up Group Exit

2 Touch GROUP and FACE UP to highlight them.
Output Modes 7-31

Output Modes
Face Up Exit (continued)

To Set Face Up Rotation Group Exit

2 Touch ROTATION GROUP and FACE UP to highlight it.
7-32 Output Modes

DL650us08v1.fm 1 ページ２００１年１１月１４日　水曜日　午後３時１７分
Section 8: Special Original

Original Direction
Text/Photo Enhance
Special Original
Mixed Original
Z-Folded Original
Original Form
Special Original 8-1

Special Original
When SPECIAL ORIGINAL on the Basic Screen is touched, the Special Original Screen
will be displayed. If one function on the menu is incompatible with another, it will appear
grayed out.
The function keys initially selected for each of four sections are highlighted. Touch and
highlight the desired key to change the standard setting. Some function keys display
subsequent screen when touched.
When all settings are made for each function, the OK key can be touched to complete the
settings, and return you to the Basic Screen. With the Basic Screen displayed, you can
press [Start] key to perform the operation.
To cancel the change before returning to the Basic Screen, touch CANCEL.
To recall the standard setting of the Special Originals, touch RECALL STANDARD.
Basic Screen Spefcial Original Screen
8-2 Special Original

Special Original
Original Direction
Specify the direction of the originals placed on EDH or platen glass.
This setting is required to obtain copy results as expected when making double-sided
copies with binding position specified or when staple position is specified.
Originals on EDH: Originals on platen glass:

A A
Z
Z
Z
Z
A
A
Z
Z
A A
A
A
Z
Z
2 Touch to highlight the desired original direction key.
4 Make other compatible selections.
5 Position original(s) in the EDH or on the platen glass.
When using Platen store mode, see p. 6-35 to p. 6-36.
When using EDH store mode, see p. 6-37.
6 Press [Start].
After copying is completed, press [Panel Reset] to release the mode and reset the
machine.
Special Original
Text/Photo Enhance
Use this function to enhance the reproducibility of half tone and produce an image closer
to that of the original.
Text Mode
Use the Text mode when copying a text original. In this mode, text is improved in
comparison to using the general mode.
Photo Mode
Use the Photo mode to reproduce a half-tone photo image. The copy will closely represent
the half-tones of the original image.
Increase Contrast Mode

Select Increase Contrast to darken lightly printed images (e.g., pencil) without changing
background exposure. In cases where the image is light and background is dark, the
background will not be changed.
❒ Original/Copy paper: 11"x17", 8.5"x14", 8.5"x11", 8.5"x11"R, 5.5"x8.5"

❒ Incompatible Copying Conditions: None
Option: In each enhance mode, the copy density level can be shifted three levels darker or three levels lighter
(Density Shift). See p. 6-14 to p. 6-15, if this setting is desired.

Special Original
Text/Photo Enhance (continued)
Original Auto mode Photo mode
Original Auto mode

Increase contrast
mode
Original Auto mode Text mode
2 Touch Text, Photo, or Increase Contrast, as required.
4 Select additional copying features, as desired.
5 Enter print quantity.
Option: Press [Mode Check] to view the selection, and make the Proof copy, if desired; then touch EXIT to
return to the Basic Screen. See p. 6-43 to p. 6-45.
7 Press [Start].
machine.

Special Original
Special Original
Mixed Original
Use the Mixed original mode with the EDH or with Store mode to copy ledger (11"x17"),
legal (8.5"x14"), letter (8.5"x11") and 5.5"x8.5"*, or legal (8.5"x14"),
letter R (8.5"x11"R and 8.5"x11") and 5.5"x8.5"* originals. Each original in the mixed set
will be copied to paper of the same size (APS mode) or to paper of desired size with
appropriate ratio automatically selected (AMS mode).
❒ Use EDH.
❒ Platen store mode is available.
❒ Original paper: 11"x17", 8.5"x14", 8.5"x11" and 5.5"x8.5"* mixed (16 lb ~ 32 lb)
8.5"x14", 8.5"x11"R, 8.5"x11" and 5.5"x8.5"* mixed (16 lb ~ 32 lb)
* 5.5"x8.5" original is available in crosswise type feeding only.
❒ EDH capacity: Max. 100 sheets
❒ APS is automatically selected (can be switched to AMS when copy size is selected).
❒ Rotation can be used with AMS.
❒ Incompatible Basic Copying Conditions: Staple-Sort with APS, Rotation Sort, Folding, Stapling &
Folding, Three-Folding, Punching (APS mode and/or 8.5"x11", 5.5"x8.5" mixed)
❒ Incompatible Special Original: Z-Folded Original, Non STD Size, Tab Paper
Interleave, Image Insert, Book Copy, Program Job, Non-Image Area Erase, Repeat, AUTO
Layout, Overlay, Storing image in Overlay Memory

Special Original
Special Original (continued)
Mixed Original (continued)
Mixed size originals APS mode
Mixed size originals AMS mode
2 Touch Mixed Original.
4 Touch OK to complete the setting and to return to the Basic Screen.
5 Select APS mode to copy each original size to a matching copy size in 1:1 mode or
select AMS mode to copy all originals to the same paper size, with a ratio selected
automatically.
APS is automatically selected.
To select AMS, touch the tray key on the Basic Screen to select the desired copy size.
7 Position mixed originals FACE UP in the EDH; 11"x17", 8.5"x14", 8.5"x11" and 5.5"x8.5"
mixed, or 8.5"x14", 8.5"x11"R, 8.5"x11" and 5.5"x8.5" mixed.
Option: Press [Panel Check] to view the selection, and make the Proof copy, if desired; then touch EXIT to
return to the Basic Screen. See p. 6-43 to p. 6-45.
8 Press [Start].
machine.

Special Original
Special Original (continued)
Z-Folded Original
Use the Z-folded original mode with the EDH to copy Z-folded originals so as not to cause
paper misfeed.
❒ Use EDH.
❒ EDH capacity: Max. 100 sheets
❒ Incompatible Basic Copying Conditions: Using platen glass
❒ Incompatible Special Original: Mixed Original, Non STD Size, Tab Paper
❒ Incompatible Applications: Non-image area erase, Repeat, AUTO layout, Storing image
in Overlay Memory
2 Touch Z-Folded original.
6 Position Z-folded original(s) in the EDH.
NOTE: Normal originals can also be loaded at the same time.
7 Press [Start].
machine.

Special Original
Original Form
The copier usually detects the standard size of originals fed through EDH or positioned on
the platen glass (STD size mode).
Use Non STD size mode to specify the scanning area manually for copying or printing
special size originals. Use the Tab paper mode to copy a tabbed original, including the
image of the tab part, onto tabbed copy paper.
❒ Scanning sizes in Non STD size mode: 11"x17", 8.5"x14", 8.5"x11"R, 8.5"x11", 5.5"x8.5"R, A3,
B4, A4R, B5R, A4, B5, WHOLE AREA
❒ Original sizes in Tab paper mode: 8.5"x14", 8.5"x11"R, 8.5"x11", A3, B4, A4R, A4, B5
❒ Tab extension width: 0.5" (12.5 mm) or less
❒ Incompatible Special Original: Mixed Original, Z-Folded Original (Non STD Size and Tab Paper
cannot be selected at the same time.)
Interleave, Image Insert, Book Copy, Storing image in Overlay Memory (Non STD size and Tab
paper)
❒ Incompatible WHOLE AREA of Non STD size: Combination, Booklet, Book Copy, Non-Image
Area Erase, Image Shift
Special Original Screen Popup menu for Non STD size mode
Popup menu for Tab paper mode
2 Touch Non STD Size or Tab paper.
3 Touch the desired size key. When selecting WHOLE AREA on the Non STD size mode
menu, the copier scans the whole area of the platen glass and copies with the paper
size or magnification ratio currently selected.
Special Original
Original Form (continued)
4 Touch OK on the popup menu of the size keys.

7 Position original(s) FACE UP in the EDH, or FACE DOWN on the platen glass.
8 Press [Start]. After copying is completed, press [Panel Reset] to release the mode and
reset the machine.

DL650us091v1.fm 1 ページ２００１年１１月１４日　水曜日　午後３時１９分
Section 9 : Applications
Application Function Menu

Sheet/Cover Insertion
Chapter
Combination
Booklet
Image Insert
Book Copy
Program Job
Non-Image Area Erase
Reverse Image
Repeat Image
Frame/Fold Erasure
AUTO Layout
All-Image Area
Image Shift
To Adjust Position of Copy Image
To Reduce and Shift Copy Image
Stamp
Overlay
Overlay Memory
To Store Overlaying Image Data in HDD
To Overlay Image Stored in HDD
Applications 9-1
Applications
Application Function Menu
When APPLI. key on the Basic Screen is touched, the Application Selection Screen
displays on the touch panel. If one function on the menu is incompatible with another, it will
appear grayed out.
When a function key is touched, it becomes highlighted. If you touch a function key,
another screen or two will display to enable you to enter the appropriate settings. For
example, you may select Repeat from the Application Selection Screen and then choose a
desired repeat image mode, another screen will display when you touch ENTER REPEAT
WIDTH BY KEYPAD, which allows you to specify the repeat width using the touch screen
keypad. Check BOOK MARK in the message area of the subsequent screen, if desired, so
that the screen may be directly accessed from the Mode Check Screen to change the
setting you made.
When all settings are made for each function, the OK key can be touched to complete the
settings, and return you to the Application Selection Screen. If no other Applications are
desired, the OK key can be touched again to complete your selections, and bring you back
to the Basic Screen. With the Basic Screen displayed, you can press the [Start] key to
perform the operation.
To restore the original copying conditions, touch CANCEL.
To clear all Application settings, touch ALL CLEAR.
Basic Screen Application Selection Screen
NOTES: 1 The APPLI. key on the Basic Screen will be highlighted when application selections have been made.
2 When incompatible selections are made, the last key touched will be selected.
3 To cancel individual functions in application mode, touch the highlighted key.
To cancel all application selections, touch ALL CLEAR key on the Application Selection Screen.
9-2 Applications
Applications
Use Sheet/Cover Insertion in copy mode or blank mode to insert chapter sheets or
separator sheets into the finished set, as well as front and back covers.
Specifications for Sheet/Cover Insertion

❒ Scan and store originals into memory, then print all the pages collectively.
❒ Max. insert sheets: 30 locations, from 1~999, including front and back covers
❒ Original paper: 11"x17", 8.5"x14", 8.5"x11", 13 lb ~ 34 lb
❒ AMS Automatic Magnification Selection: Functions when a different copy size is selected.
❒ Incompatible Basic Copying Conditions: APS, Group, Cover Sheet mode, Rotation Sort, Rotation
Group, Punching
❒ Incompatible Special Originals: Mixed Original, Tab Paper
❒ Incompatible Applications: Combination, Booklet, Transparency Interleave, Image Insert, Book
Copy, Program Job, Non-Image Area Erase, Repeat, AUTO Layout, Overlay, Storing image in
Overlay Memory
Sheet/Cover Insertion Screen
Applications 9-3
Applications
Sheet/Cover Insertion (continued)
Insertion Mode
This mode is classified as Copy insertion and Blank insertion. The Copy insertion mode
copies and inserts plain or colored sheets at locations designated in the page setting area
of the Sheet/Cover Insertion Screen. The Blank insertion mode inserts non-copied (plain
or colored) sheets.
The tray source for insertions can be selected and displayed on the Sheet/Cover Insertion
Screen.
Front Cover Mode

This mode is classified as Front copy and Front blank. The Front copy mode copies and
inserts a plain or colored sheet into the finished set, as a Front cover. The Front blank
mode inserts a non-copied plain or colored sheet into the finished set, as a Front cover.
When either Front copy or Front blank is selected, the corresponding icon will appear on
the upper-left corner key in the page setting area of the Sheet/Cover Insertion Screen.
The tray source will be the same as that for back cover, and can be selected and displayed
on the Sheet/Cover Insertion Screen.
Back Cover Mode

This mode is classified as Back copy and Back blank. The Back copy mode copies and
inserts a plain or colored sheet into the finished set, as a Back cover. The Back blank
mode inserts a non-copied plain or colored sheet into the finished set, as a Back cover.
When either Back copy or Back blank is selected, its icon will appear as the last (fixed) key,
with one active blank key preceding it in the page setting area of the Sheet/Cover Insertion
Screen.
The tray source will be the same as that for front cover, and can be selected and displayed
on the Sheet/Cover Insertion Screen.
The insertion type can be selected separately for front cover, back cover, and insertion
sheets. This allows multiple combinations, such as blank front cover and copied insertions.
See the following illustration for details.
9-4 Applications
Applications
Basic Functions Combination samples

9 10 9 10
78 9 10 78 9
56 78 56 7 8 10
34 4 56 34 4 56
12 23 12 23
SURVEYOR’S SURVEYOR’S
REPORT REPORT
SURVEYOR’S 1 SURVEYOR’S 1
REPORT REPORT
Originals Copies Originals Copies

FRONT COVER COPIED FRONT & BACK COVERS COPIED
10 10
89 9 10 89 9 10
67 78 67 78
45 56 45 56
23 34 23 34
SURVEYOR’S 1 SURVEYOR’S 12 SURVEYOR’S 1 SURVEYOR’S 12
REPORT REPORT REPORT REPORT
Originals Copies Originals Copies

FRONT COVER BLANK FRONT & BACK COVERS BLANK
10
89 9
67 7 8 10
45 56
23 4
SURVEYOR’S 1 23
SURVEYOR’S 1
REPORT REPORT
10
89
67 89
45 56 10
23
SURVEYOR’S 1 23 7
4
REPORT
SURVEYOR’S 1
REPORT
Originals Copies
BACK COVER COPIED
9 10
78 9 10
34
56
56
78 Originals Copies
12 4
SURVEYOR’S 23
SURVEYOR’S 1
REPORT REPORT FRONT & BACK COVERS COPIED,
AND COPY SHEET INSERTION
9 10 9 10
Originals Copies 78 78
56 6
34 45
BACK COVER BLANK SURVEYOR’S 12
12
3
SURVEYOR’S
REPORT REPORT
9 10 10
78 89
56
34 56
12 23 7
SURVEYOR’S SURVEYOR’S 1 4
REPORT REPORT
Originals Copies
FRONT & BACK COVERS BLANK,
Originals Copies AND BLANK SHEET INSERTION
COPY SHEET INSERTION
9 10 9 10
78 78
56 6
34 45
12 3
SURVEYOR’S 12
SURVEYOR’S
REPORT REPORT
Originals Copies
BLANK SHEET INSERTION
Applications 9-5
Applications

Application Selecftion Screen Sheet/Cover Insertion Screen
Sheet/Cover Insertion Screen

(with FRONT COPY, BACK COPY and COPY INSERT selected)
Max. insertion locations: 30

1 Touch APPLI. on the Basic Screen to display the Application Selection Screen.
2 Touch Sheet/Cover Insertion to display the Sheet/Cover Insertion Screen.
3 Select Front Cover Insertion, if desired.
Touch FRONT COPY to insert a copied front cover, or FRONT BLANK to insert a blank
front cover.
Proceed to step 4 to select Back Cover Insertion, if desired.
Proceed to step 5 to select Sheet Insertion, if desired.
4 Select Back Cover Insertion.
Touch BACK COPY to insert a copied back cover, or BACK BLANK to insert a blank
back cover.
Return to step 3 to select Front Cover Insertion, if desired.
Proceed to step 5 to select Sheet Insertion, if desired.
5 Select Sheet Insertion.
Touch COPY INSERTION to insert copied sheets, or BLANK INSERTION to insert blank
sheets.
Return to step 3 to select Front Cover Insertion, if desired.
Return to step 4 to select Back Cover Insertion, if desired.
9-6 Applications
Applications
6 The page setting area of the Sheet/Cover Insertion Screen displays 15 keys to
designate each insertion location.
The first (upper left) key displays the Front Cover icon if selected. The Back Cover icon
appears, if selected, as the last (fixed) key, with one active blank key preceding it. (See
the previous page.)
Use the control panel keypad to enter the page number of each insertion location.
Touch SET after each entry to move to the next key.
Example: If p. 4 is entered in blank mode, a blank sheet will be inserted between p. 4
and p. 5; in copy mode, a copied sheet is inserted at p. 4.
To clear an incorrect entry, touch DELETE or press [C] (Clear). The insertion location will
be deleted.
When setting more than 15 locations, touch the arrow key to move to the next page.
NOTES:
1 The page numbers entered at random will be sorted automatically.
2 Entering “0” or the same page number twice will be ignored on the screen.
3 When a page number entered is larger than the total original page count, it will be ignored.
7 The tray sources for covers and insertions currently selected are displayed on the Sheet/
Cover Insertion Screen.
Touch CHANGE OF THE COVERS TRAY or CHANGE OF THE INSERTION TRAY to select
another tray, if desired. At every touch the key shifts the selection in the display that
includes paper type, if specified in Key Operator mode.
When all settings are completed, touch OK to return to the Application Selection Screen.
11 Position originals FACE UP in the EDH.
Option: Press [Panel Check] to view the selection, and make a Proof copy, if desired. Touch EXIT to return to
the Basic Screen. See p. 6-43 to p. 6-45.
12 Press [Start].
After copying is completed, touch Sheet/Cover Insertion on the Application Selection
Screen or press [Panel Reset] to release the mode and reset the machine.
Applications 9-7
Applications
Chapter
Chapter is used with the EDH in 1-2 mode for the purpose of locating title pages on the
right side, rather than reverse side, of a duplex copy.
To effectively locate the title page on the right, a blank sheet will be automatically created
on the reverse side of a sheet, if required.
❒ Title pages: Max. 30 from 1 ~ 999

❒ Copy mode: 1-2 mode is automatically selected. (2-2 mode can be selected.)
❒ Use EDH.
Store mode is also available; in this case use platen glass or EDH.
❒ Use STAMP together with this function to print chapter number onto chapter page in addition to
page number, numbering, or watermark numbering. See p. 9-39 to p. 9-43.
❒ Incompatible Basic Copying Conditions: 1-1, 2-2, 2-1, Group, Punching (when selecting Copy
insertion mode), Rotation Sort, Rotation Group, Face Up
❒ Incompatible Applications: Combination, Transparency Interleave, Image Insert, Program Job,
Non-Image Area Erase, Repeat, Storing image in Overlay Memory
1-sided originals Copies in Chapter mode

Tilte page
7
5
3
8
7 8 6
5
34 4
1 2 6 2
1
Title pages
Title page
Application Selection Screen Chapter Insertion Setting No. Screen
9-8 Applications
Applications
Chapter (continued)
2 Touch Chapter. The Chapter Insertion Setting No. Screen will be displayed. The 1-2
copy mode is automatically selected.
3 Use the keypad on the control panel to enter the page number of each title page.
4 Touch SET.
To clear an incorrect entry, touch DELETE or press [C] (Clear). The insertion location will
be deleted.
To enter the correct page number, touch SET and use the keypad.
5 Repeat this for each title page number you want to appear on the right hand side.
When setting more than 15 locations, touch the arrow key to move to the next page.
Be sure to touch SET after each page number entry, up to a total of 30 entries.
Option: Touch Booklet on the Chapter Insertion Setting No. Screen to use this function. To change the
selection of paper tray for copying title pages, touch Copy Insertion on the screen. In this case, you
can touch CHANGE OF THE INSERTION TRAY to change the currently selected paper tray displayed
on the screen.
6 When all entries are made, touch OK to return to the Application Selection Screen.
10 Position originals FACE UP on the EDH. 100 originals can be set.
11 Press [Start].
After copying is completed, touch Chapter on the Application Selection Screen or press
[Panel Reset] to release the mode and reset the machine.
NOTES:
1 Entering “0” or the same page number twice will be ignored on the screen.
2 Chapter insertions occur in sequence even if original page numbers are entered out of sequence.
3 When a page number entered is larger than the total original page count, it will be ignored.
Applications 9-9
Applications
Combination
Use this function to lay out and copy a fixed number (2, 4, or 8) of pages onto one sheet of
copy paper (2 in 1, 4 in 1, or 8 in 1).
Combination Specifications
❒ Scan and store originals into memory.
❒ Use EDH.
Store mode is also available; in this case, use platen glass or EDH.
❒ AMS is automatically selected.
❒ Original/Copy size: 11"x17", 8.5"x14", 8.5"x11"R, 8.5"x11", 5.5"x8.5"
❒ Incompatible Basic Copying Conditions: APS, Group, Rotation Sort, Rotation Group
❒ Incompatible Special Originals: Mixed Original
❒ Incompatible Applications: Sheet/Cover Insertion, Chapter, Booklet, Transparency Interleave,
Image Insert, Book Copy, Program Job, Non-Image Area Erase, Repeat, Storing image in
Overlay Memory
Layout Horizontal order Vertical order

Original 2 in 1 4 in 1 8 in 1 4 in 1 8 in 1
Portrait type
1 2 1 3
1 2 3 4 1 3 5 7
1 2
5 6 7 8 2 4 6 8
3 4 2 4
Landscape type 1 2 1 5
1 2 3 4 1 3 2 6
3 4 5 6 2 4 3 7
7 8 4 8
Application Selection Screen Combination Mode Selection Screen
9-10 Applications
Applications
Combination (continued)
2 Touch Combination to display the Combination Mode Selection Screen.
3 Touch 2 in 1, 4 in 1, or 8 in 1 in the desired order area, referring to the illustration on the
previous page.
4 Touch OK to return to the Application Selection Screen.
7 AMS is automatically selected. When selecting any tray other than the one that is set
and displayed on the Basic Screen, touch the desired tray key.
9 Place original(s) FACE UP in the EDH.
10 Press [Start].
After copying is completed, touch Combination on the Application Selection Screen or
press [Panel Reset] to release the mode and reset the machine.
Applications 9-11
Applications
Booklet
Use the Booklet mode to make a multiple page signature booklet on both sides of paper
from any tray unless it is specified as Thick or Tab Paper paper type in the Key Operator
mode. Original images are scanned into memory and automatically arranged in booklet
format in correct order.
❒ Scan and store original into memory, then print all the pages collectively.
❒ Original pages should be a multiple of 4 in 1-1 mode or a multiple of 2 in 2-2 mode; otherwise,
blank pages will be automatically inserted to compensate.
❒ Copy mode: 1-2 or 2-2 mode only.
❒ Folding or Stapling & Folding output mode is available when copier is equipped with 9922
Finisher.
❒ Incompatible Basic Copying Conditions: 1-1, 2-1, APS, Group, Punching (when selecting Cover
sheet mode), Rotation Sort, Rotation Group, Face Up, 9924 Cover Inserter with Cover mode in
Booklet
❒ Incompatible Applications: Sheet/Cover Insertion, Combination, Transparency Interleave,
Program Job, Non-Image Area Erase, Repeat, Storing image in Overlay Memory
1-sided originals ..............
1 2 3 4 47 48
Booklet copying ..............

24
47
45
25
2
48 1 46 3 26 23
1 3 5 7 45 47
2-sided originals ..............

46
48
2
Application Selection Screen Booklet Mode Selection Screen
9-12 Applications
Applications
Booklet (continued)
1 Load the desired copy paper size in a tray. When selecting cover sheet mode (COVER
WITH COPY SHEET or COVER WITH BLANK SHEET), load the same size paper in any
tray unless it is specified as Thick or Tab Paper paper type in the Key Operator mode.
3 Touch Booklet to enter the Booklet Mode Selection Screen.
4 Touch NO COVER SHEET, COVER WITH COPY SHEET, or COVER WITH BLANK SHEET,
as required. When a cover sheet is required, touch CHANGE OF THE COVERS TRAY to
select the cover sheet tray source.
Touch CHANGE OF THE OUTPUT MODE if you want to change the binding mode.
5 Touch OK.
NOTE: Key Operator can set the machine to position the page numbers automatically on the outside edges of
the copy when using Booklet with Page Numbering in Stamp. See p. 14-40 to p. 14-45.
7 Touch OK on the Application Selection Screen to complete the selections and return to
the Basic Screen.
8 Select the 1-2 or 2-2 copy mode.
9 AMS is selected automatically. When selecting any tray other than the tray that is set
and displayed on the Basic Screen, touch the desired tray key. To release AMS, select
the desired magnification, then select copy size.
10 If the copier is equipped with 9922 Finisher, Folding/Stapling & Folding output mode is
available. Follow the procedure below.
(1) Touch OUTPUT APPLI. on the Basic Screen to display the Output Menu Screen,
then touch MAIN TRAY to highlight it.
(2) Touch STAPLING & FOLDING or FOLDING, as desired.
NOTE: Selecting FOLDING or STAPLING & FOLDING will automatically switch the output tray to Booklet
tray. Notice that the arrow pointing to the MAIN TRAY shifts to the Booklet tray.
Output Menu Screen
(2) Touch OK on the Output Menu Screen. The Basic Screen will be restored with the
OUTPUT APPLI. highlighted.
Applications 9-13
Applications
Booklet (continued)
12 Position originals FACE UP onto the EDH.

NOTE: When loading originals, heed the following limits on capacity:
Folding mode: 12 pages or less for simplex originals
6 pages or less for duplex originals
Stapling & Folding mode: 80 pages or less for simplex originals
40 pages or less for duplex originals
Exceeding the above limits on capacity may cause misfeeds in the finisher.
13 Press [Start].
After copying is completed, touch Booklet on the Application Selection Screen or press
CAUTION
The roller drive unit is located inside the Booklet tray of the finisher. DO NOT put your hand into the roller
drive unit when removing folded or stapled & folded sheets; otherwise, you may be injured.
9-14 Applications
Applications
Use the Transparency interleave function in 1-1 or 2-1 mode to copy onto overhead
projection transparencies and output a blank or copied interleaf sheet with each copied
transparency.
In the blank mode, a blank interleaf sheet is output with each transparency to keep the film
material from sticking together.
In the copy mode, a copied interleaf sheet is output with each transparency to provide
reference during a presentation, a medium for photocopying, and a set for filing or
inserting into a binder.

❒ Transparency source: Multi-sheet bypass tray
❒ Multi-sheet bypass tray capacity: 1 transparency sheet
❒ Transparency size: 11"x17", 8.5"x14", 8.5"x11"R, 8.5"x11"
❒ Interleaving paper source: Tray 1, 2, 3, or LCC
❒ Interleaving paper size: 11"x17", 8.5"x14", 8.5"x11"R, 8.5"x11"
❒ Number of originals/number of copies: 1
❒ Incompatible Basic Copying Conditions: APS, 1-2, 2-2, Staple-Sort, Sort, Group, Rotation Sort,
Rotation Group, Folding, Stapling & Folding, Three-Folding, Punching, Using 9924 Cover Inserter
❒ Incompatible Applications: Sheet/Cover Insertion, Chapter, Combination, Booklet, Image Insert,
Program Job, Repeat, Overlay, Storing image in Overlay Memory
Original Blank sheet Interleaving Copy sheet Interleaving
Applications 9-15
Applications
Transparency Interleave (continued)

Application Selection Screen Transparency Interleave Screen
1 Load copy paper in tray 1, 2, 3, or 4 to match the size of transparencies.

2 Open the Multi-sheet bypass tray. Insert one transparency at a time into the Multi-sheet
bypass tray, and adjust the paper guides.
IMPORTANT: do not load transparencies into any other tray.
4 Touch Transparency Interleave to display the Transparency Interleave Screen.
5 Touch Blank sheet Interleaving or Copy sheet Interleaving, unless it is already
highlighted.
6 Touch OK.
7 Make additional Application selections, or touch OK to return to the Basic Screen.
8 Print quantity is already set to 1. Not available to enter any other number.
9 Place original FACE UP in the EDH or FACE DOWN on the platen glass.
10 Press [Start].
After copying is completed, touch Transparency Interleave on the Application Selection
9-16 Applications
Applications
Image Insert
Use the Image insert mode to combine images scanned from the platen glass, such as
photos, paste-ups, newspaper articles, graphs, etc., with images scanned from the EDH.
Then, output the combined images as a finished set.
The selected copy paper size is determined by the size of originals loaded in the EDH.
❒ All images are stored in memory.

❒ Max. image insert: 30 locations
❒ Incompatible Basic Copying Conditions: Group, Rotation Sort, Rotation Group
❒ Incompatible Applications: Sheet/Cover Insertion, Chapter, Combination, Transparency
Interleave, Book Copy, Program Job, Non-Image Area Erase, Repeat, AUTO Layout, Overlay,
Storing image in Overlay Memory
Place originals
onto EDH
7 8
6
7 8 5
6
45 34
23 2
1 1
Insertion originals
Place originals
8
onto EDH
6
8
6
4
7
2
7 5
5 4
3
1 1
Application Selection Screen Image Insertion No. Setting Screen
Applications 9-17
Applications
Image Insert (continued)
1 Review pages to be scanned from the EDH, and note the page number locations for
inserting images scanned from the platen glass.
To insert more than one sheet at the same location, enter the page number repeatedly.
For example, if insertion locations are [2/2/6], scanned platen images will be inserted as
follows:
• The first scanned platen image will be inserted after page 2.
• The second scanned platen image will be inserted directly after the first scanned
Image insertion.
• The third scanned platen image will be inserted after page 6.
3 Touch Image Insert to display the Image Insertion No. Setting Screen.
4 Use the keypad to enter the page numbers for up to 30 insertion locations, touching SET
after each entry.
• When a page number is larger than the total original count, a sheet is inserted as the
last page.
• Insertions occur in sequence, even if page numbers are entered out of sequence.
• To clear an incorrect entry, touch DELETE or [C](Clear), then enter the correct page
number.
• When setting more than 15 locations, touch the arrow key to move to the next page.
Option: Touch Booklet on the Image Insertion No. Setting Screen to use this function.
5 When all page number entries are made, touch OK. The Application Selection Screen
will be restored. Select additional copying features, as desired.
6 Touch OK to complete the setting and return to the Basic Screen. The Store mode is
automatically selected.
8 Scan the EDH images.
(1) Position originals FACE UP in the EDH.
(2) Press [Start] to scan originals.
9 Scan the platen glass images.
(1) Open the EDH.
(2) Position an original FACE DOWN on the platen glass, then close the EDH.
IMPORTANT: PLACE AND SCAN THE ORIGINALS ACCORDING TO PAGINATION.
(3) Press [Start] to scan the original.
(4) Remove the original, and repeat for each original.
Be sure to press [Start] for each original.
Option: Press [Panel Check] to view the selection, and make a Proof copy if desired; then EXIT to return to
10 Start printing.
(1) Touch STORE to deselect it.
(2) Press [Start].
After copying is completed, touch Image Insert on the Application Selection Screen or
9-18 Applications
Applications
Book Copy
Use this function to copy an open book or a ledger sheet onto two 8.5"x11" sheets in 1-1
mode, or onto the front and back sides of one 8.5"x11" sheet in 1-2 mode. If you select
another paper size, image division will perform incorrectly.
The following three modes can be selected from the Book Copy Screen.
1 Full Scan mode: Image division starts from the first scan.
2 Front Cover + Full Scan mode: Image division starts from the second scan, after the
first scan copies normally.
3 Front/Back Cover + Full Scan mode: Image division starts from the third scan, after
the first and second scan copy normally.
❒ Scan and store originals into memory, then print all pages collectively.
❒ Original size: Max. 11"x17" (ledger) sheet or open book
❒ Copy paper size: 8.5"x11" (letter)
❒ Incompatible Basic Copying Conditions: APS, AMS, Rotation Sort, Rotation Group, Folding /
Stapling & Folding / Three-Folding
❒ Incompatible Applications: Sheet/Cover Insertion, Combination, Image Insert, Program Job,
Repeat, Reduce & Shift in Image Shift, Overlay, Storing image in Overlay Memory
1-1 mode 1-2 mode
Application Selection Screen Book Copy Screen
Applications 9-19
Applications
Book Copy (continued)
1 Load 8.5"x11" sheets in a tray or in the Multi-sheet bypass tray.

3 Touch Book Copy to enter the Book Copy Screen.
4 Touch Full scan, Front cover + Full scan, or Front/Back cover + Full scan, as required.
Touch REVERSE THE SIDE OF OPEN PAGE to change the binding mode according to
the original.
Option: Touch Booklet on the Book Copy Screen to use this function.
6 Make additional application selections, or touch OK to return to the Basic Screen. The
Store mode is automatically selected.
7 Select the copy mode (1-1 or 1-2).
9 Position the open book or sheet on the platen glass in the left rear corner, aligning the
edge with the left measuring guide. When opening the EDH, Non-Image Area Erase and
AUTO Layout are automatically selected.
IMPORTANT: KEEP THE EDH OPEN THROUGHOUT THE SCANNING PROCEDURE OF
THE PLATEN STORE MODE.
If Full scan is selected and the originals can be loaded in the EDH, EDH store mode is
also available. If desired, position originals into the EDH.
Option: Press [Panel Check] to view the selection and make a Proof copy. Touch EXIT to return to the Basic
Screen. See p. 6-43 to p. 6-45.
10 Press [Start] to start scanning.
11 Remove the first original(s). Repeat the procedure for subsequent originals, pressing
[Start] for each original.
When Front cover + Full scan or Front/Back cover + Full scan is selected, only the
front and back covers are required to be scanned from the platen glass. If you want to
use EDH store mode for scanning the rest of the originals, close the EDH and position
originals, then press [Start].
12 Touch STORE to deselect the store mode, then press [Start] to print.
After copying is completed, touch Book copy on the Application Selection Screen or
9-20 Applications
Applications
Program Job
In the ordinary Store mode, the combined features selected for the job are applied to all
originals to be scanned. In the Program Job mode, you may scan multiple sets of originals
and apply different settings on each set (referred to as JOB), then output them all as a
complete set.
❒ Scan and store originals into memory, then print all the pages collectively.
❒ Max. 100 JOBs can be programmed for an output job.
❒ Available original sizes vary conforming to copy conditions selected for each JOB.
❒ Copy size specified for the first JOB cannot be changed. Only the trays containing the same
paper size can be designated for subsequent JOBs.
Once specified, paper type/size setting for Multi-sheet bypass tray cannot be changed for another
JOB.
❒ Output mode settings cannot be specified for each JOB. The last settings made will be applied to
all JOBs.
❒ Print quantity cannot be specified for each JOB. Entered quantity will be the number of complete
copied sets and can be changed anytime before printing.
❒ Program Job settings cannot be stored in Job Memory.
❒ Incompatible Basic Copying Conditions: APS, Change copy size, Rotation, Group, Rotation Sort,
Rotation Group, Folding, Stapling & Folding, Three-Folding, Punching, Server function
Interleave, Image Insert, Book Copy, 2/4/8 Repeat in Repeat, Overlay, Storing image in Overlay
Memory
9 10
78
56 56
34 34
12 12 12
Original A Original B Original C

9 10
78
56
34
12
56
34
12
12
Copied set
Applications 9-21
Applications
Program Job (continued)

Application Selection Screen Basic Screen with popup menu displayed
2 Touch Program Job. The incompatible function keys will be dimmed to show inactivity.
5 Store mode is selected automatically. Select basic copying and special original features
on the Basic Screen and Special Original Screen, as desired.
6 Position original(s) FACE UP in the EDH or FACE DOWN on the platen glass, select the
tray you want to use, then press [Start] to scan.
7 When scanning for the current JOB is completed, the popup menu will be displayed in
the Basic Screen.
To store the current JOB images, touch DECISION.
To delete the images, touch CANCEL.
8 Repeat steps 3 to 7 until all JOB originals are scanned.
IMPORTANT: PLACE AND SCAN EACH ORIGINAL SET IN THE CORRECT ORDER OF
PAGINATION.
9 Select the desired output mode.
11 Touch STORE on the Basic Screen to exit the Store mode.
machine.
9-22 Applications
DL650us092v1.fm 23 ページ２００１年１１月１４日　水曜日　午後３時２１分
Applications
The Non-image area erase mode is used to copy non-standard or special originals, such
as books, magazines, paste-ups, graphs, thin or thick materials, etc. from the platen glass.
The exposed glass area outside the borders of the original will not be copied.
This mode helps to preserve the condition of originals, improves copy quality, and
eliminates unnecessary toner consumption. Keep the EDH open throughout the
procedure.
Non-image area erase has two modes; Rectangular erase mode and Oblique erase mode.
The copier is initially set to select either mode appropriate for the original placed on the
platen glass (AUTO mode). Key Operator can specify either mode and the original density
level manually so that the Non-Image Area Erase functions without fail.
Oblique erase mode Rectangular erase mode
❒ Copy mode: 1-1 mode only (when using Store mode, 1-2 mode can be selected.)
❒ Use the platen glass only. Keep the EDH open throughout the scanning procedure.
❒ Original size: 11"x17" ~ 10mm x 10mm
❒ Image cutoff width: leading end 5mm, trailing end 4mm, top and bottom 2mm.
❒ Incompatible Basic Copying Conditions: Using EDH, APS, AMS, Rotation, 2-2, 2-1, Rotation
Sort, Rotation Group
❒ Incompatible Special Originals: Mixed Original, Z-Folded Original
Book Copy in EDH Store mode, Reverse Image, All-Image Area, Reduce & Shift in Image Shift,
Storing image in Overlay Memory
NOTE: The Non-image area erase function may not operate properly if the lighting in the work place is directly
over the platen glass. In this case, consult your service representative about an appropriate place for
installation.
Applications 9-23
Applications
Non-Image Area Erase (continued)
General copying
Set original
Application Selection Screen
2 Touch Non-image Area Erase.
6 Position original(s) FACE DOWN on the platen glass.
IMPORTANT: KEEP THE EDH OPEN THROUGHOUT THE PROCEDURE.
Option: Press [Mode Check] to view the selection, and make a Proof copy, if desired. Touch EXIT to return to
7 Press [Start].
After copying is completed, touch Non-image Area Erase on the Application Selection
9-24 Applications
Applications
Reverse Image
Use Reverse image to reverse the image from black-on-white to white-on-black, and vice
versa.
❒ Original/Copy paper: 11"x17", 8.5"x14", 8.5"x11", 8.5"x11"R, 5.5"x8.5"

❒ Incompatible Basic Copying Conditions: Folding, Stapling & Folding, Three-Folding
❒ Incompatible Applications: Non-Image Area Erase, Repeat, All-Image Area, Stamp, Overlay
Memory
Original Reverse Image copying
2 Touch Reverse Image.
Option: Press [Mode Check] to view the selection, and make a Proof copy, if desired. Touch EXIT to return to
7 Press [Start].
After copying is completed, touch Reverse Image on the Application Selection Screen or
Applications 9-25
Applications
Repeat Image
Use Repeat image to create labels, business cards, tickets, etc., by repeating the selected
image down the page.
Vertical/Horizontal Width Setting mode
Repeat the selected image area of 10mm ~ 150mm in both vertical and horizontal widths
measured from the rear left corner of the original area indicated on the left edge of the
platen glass.
Auto Detection mode
Selecting this mode will automatically set the equal repeat area to the size of the original
placed onto the platen glass by activating Non-image area erase.
Repeat mode
Select the repeating times of the original to be arranged in one copy sheet.
❒ Vertical/Horizontal Width Setting Mode Specifications
Use the platen glass. (The EDH cannot be used.)
Repeat width: 10~150mm (in 1mm increments)
Copy mode: 1-1 mode only (When selecting 1-2 mode, Platen store mode will function automatically.)
❒ Auto Detection Mode Specifications
Use the platen glass. Non-Image Area Erase will function automatically.
Scanning area: 11"x17" ~ 10mm x 10mm
Repeat image area: Original image area detected by Non-Image Area Erase
Copy mode: 1-1 mode only (When selecting 1-2 mode, Platen store mode will function automatically.)
❒ Repeat Mode Specifications
Magnification ratio: Set to 1.00 (100 %) automatically. Magnification can be changed, but
Rotation will not function when magnification is changed.
Scanning area: 11"x17" ~ 10mm x 10mm
Repeat image area: A portion of the selected copy size equally divided according to the mode (2,
4, or 8 Repeat) designated on the screen. If detected image size is larger than the size figured
out as above, the copy result may not be satisfactory.
❒ Incompatible Conditions with Vertical/Horizontal Width Setting Mode
Basic copying conditions: Using EDH, Rotation, 2-2, 2-1, APS, AMS, Group, Rotation Sort,
Rotation Group
Special Originals: Mixed Original, Z-Folded Original
Applications: Sheet/Cover Insertion, Chapter, Combination, Booklet, Transparency Interleave,
Image Insert, Book Copy, Non-Image Area Erase, Reverse Image, Frame/Fold Erasure, AUTO
Layout, Reduce & Shift in Image Shift, Stamp/Overlay
❒ Incompatible Conditions with Auto Detection Mode
Basic copying conditions: Using EDH, Rotation, 2-2, 2-1, APS, AMS, Group, Rotation Sort,
Rotation Group
Special Originals: Mixed Original, Z-folded Original
Image Insert, Book Copy, Reverse Image, Frame/Fold Erasure, AUTO Layout, All-Image Area,
Reduce & Shift in Image Shift, Stamp/Overlay
9-26 Applications
Applications
Repeat Image (continued)

❒ Incompatible Conditions with Repeat Mode
Basic copying conditions: Rotation (when magnification is changed from 1.00), APS, AMS,
Group, Rotation Sort, Rotation Group
Special Originals: Mixed Original, Z-folded Original
Image Insert, Book Copy, Non-image Area Erase, Reverse Image, Frame/Fold Erasure, AUTO
Layout, Reduce & Shift in Image Shift, Overlay, Overlay Memory
NOTE: The Auto Detection and Repeat mode of the Repeat image function may not operate properly if the
lighting in the work place is directly over the platen glass. In this case, consult your service representative
about an appropriate place for installation.
Vertical/Horizontal Width Auto Detection mode 2/4/8 Repeat mode

Setting mode
Horiz. width
Verti. Copy (2 Repeat)
width
Copy (4 Repeat)
Copy Copy (AUTO)

Copy (8 Repeat)
Application Selection Screen Repeat Mode Selection Screen
2 Touch Repeat to display the Repeat Mode Selection Screen.
Applications 9-27
Applications
Repeat Image (continued)
3 To select the Vertical/Horizontal width setting mode:

(1) Touch Vertical/Horizontal.
(2) Specify the vertical and horizontal widths of the scanning area using up/down arrow
key, from 10~150 mm in 1 mm increments. Keep touching the key to increase/
decrease the value continuously.
Or, touch ENTER REPEAT WIDTH BY KEYPAD to display the popup screen to enter
the value from the touch screen keypad. Touch Verti./Horiz key on the popup screen
each time to shift it from one to another. Touch OK to restore the Repeat Mode
Selection Screen
Repeat Mode Selection Screen (with popup screen displayed)
To select the Auto detection mode, touch AUTO. Non-image area erase will function
automatically.
To select the Repeat mode, touch 2 Repeat, 4 Repeat, or 8 Repeat, as desired.
When 2 Repeat mode is selected, Page space function of Image shift can be used to
make the desired amount of blank space between the two images on a page. See p. 9-
34 to p. 9-37.
8 Position original(s) FACE DOWN on the platen glass.
IMPORTANT: DO NOT CLOSE THE EDH WHEN AUTO, 2 REPEAT, 4 REPEAT, OR 8
REPEAT IS SELECTED IN STEP 3.
When using Platen store mode, 1-2 mode can be selected. See p. 6-35 to p. 6-36.
Option: Press [Mode Check] to view the selection, and make a Proof copy if desired. Touch EXIT to return to
9 Press [Start].
After copying is completed, touch Repeat on the Application Selection Screen or press
9-28 Applications
Applications
Frame/Fold Erasure
Use Frame/Fold Erasure to eliminate black copy marks along borders.
❒ Frame erasure amount: 1~300 mm in 1 mm increments

❒ Initial frame erasure value: 10 mm
❒ Fold erasure amount: 1~99 mm in 1 mm increments
❒ Initial fold erasure value: 10 mm
❒ Original/copy paper size: 11"x17", 8.5"x14", 8.5"x11"
❒ Incompatible Applications: Repeat, All-Image Area
Application Selection Screen Frame/Fold Erasure Selection Screen
Frame Frame
erasure erasure
Set original Frame Fold Frame
erasure erasure erasure
General copying Frame Erasure Fold Erasure Frame/Fold Erasure

copying copying copying
Applications 9-29
Applications
Frame/Fold Erasure (continued)
2 Touch Frame/Fold Erasure to display the Frame/Fold Erasure Selection Screen.
3 Touch Frame Erasure (All sides) or Frame Erasure (Each side). Touch Fold Erasure to
use the Fold erasure mode.
• Touch Frame Erasure (All sides) to enter the frame erasure amount of the up, down,
right and left sides collectively using the touch screen keypad or up/down arrow key,
from 1~300mm.
• Touch Frame Erasure (Each side) to enter the frame erasure amount of the up,
down, right or left side individually. Touch UP SIDE, RIGHT SIDE, DOWN SIDE, or
LEFT SIDE, then use the touch screen keypad or up/down arrow key to enter the
desired amount, from 1~300mm.
• To enter the fold erasure amount, touch Fold Erasure, then touch FOLD. Use the
touch screen keypad or up/down arrow key to enter the desired amount, from
1~99mm.
Frame/Fold Erasure Selection Screen Frame/Fold Erasure Selection Screen
(with Each side selected) (with FOLD selected)
4 Touch OK to complete the setting. The Application Selection Screen will be displayed.
5 Touch OK to return to the Basic Screen or make additional application selections.
6 Select desired Copy Size.
7 Enter desired print quantity.
9 Press [Start].
After copying is completed, touch Frame/Fold Erasure on the Application Selection
NOTE: While copy size and original size generally should be the same, it is possible to use Frame/Fold Erasure
to copy an 11"x17" original to 8.5"x11"R by selecting 0.65 reduction after selecting Copy Size.
9-30 Applications
Applications
AUTO Layout
Use this function to detect the image area of the original and center the whole image on
the copy paper.
❒ Copy mode is automatically set to 1-1; 1-2 mode is also available only when using Store mode.
❒ APS and AMS are automatically released. Changing Magnification is available.
❒ Non-image area erase is automatically selected. (Release it manually when using EDH to scan
originals.)
❒ Incompatible Basic Copying Conditions: APS, AMS, Rotaion, 2-2, 2-1, Rotation Sort, Rotation
Group
❒ Incompatible Special Originals: Mixed Original, Z-folded Original
Reverse Image, Repeat, All-Image Area, Image Shift, Overlay, Storing image in Overlay Memory
NOTE: The AUTO layout function may not operate properly if the lighting in the work place is directly over the
platen glass. In this case, consult your service representative about an appropriate place for installation.
AUTO layout copying

Set original
Applications 9-31
Applications
AUTO Layout (continued)
2 Touch AUTO Layout. The incompatible function keys will be dimmed to show inactivity.
3 Select additional copying features, as desired. When using EDH to scan originals, touch
Non-image Area Erase to deselect it.
5 Select the desired copy size.
IMPORTANT: DO NOT CLOSE THE EDH WHEN USING PLATEN GLASS. PLACING
ORIGINAL OBLIQUELY ON THE PLATEN GLASS MAY CAUSE BLACK COPY MARKS.
8 Press [Start].
After copying is completed, touch AUTO Layout on the Application Selection Screen or
9-32 Applications
Applications
All-Image Area
Use this function to make copies printed completely to the edges.
❒ Copies will be made without image cutoff on the edges.

❒ Incompatible Basic Copying Conditions: Rotation Sort, Rotation Group
❒ Incompatible Applications: Non-Image Area Erase, Reverse Image, Frame/Fold Erasure
Original Normal Copy All-Image

Area Copy
2 Touch All-image Area.
5 Select the desired copy size.
7 Position original(s) FACE UP in EDH or FACE DOWN on platen glass.
8 Press [Start].
After copying is completed, touch All-image Area on the Application Selection Screen or
Applications 9-33
Applications
Image Shift
To Adjust Position of Copy Image
Use Image Shift to create a new binding margin on originals copied in the 1-1 or 2-2 mode,
or adjust existing margins on originals copied in the 1-2 or 2-1 mode.
Page space function is available only when Booklet or 2 Repeat mode of Repeat has been
already selected. Use this function to create the desired amount of blank space between
the two images on a page.
If image loss seems likely, select the Reduce & Shift mode. See p. 9-37.
❒ Shift amount in Image Shift mode: 0 ~ 250 mm in 1 mm increments (setting in 0.1 mm increments
using up/down arrow key is also available by Key Operator setting.), to be set collectively or
individually for the front and back pages.
❒ Page Space functions only when Booklet or 2 Repeat mode of Repeat is previously selected.
❒ Original/copy size: 11"x17", 8.5"x14", 8.5"x11", 8.5"x11"R
❒ Incompatible conditions
Basic copying conditions: None
Special Originals: None
Applications: AUTO Layout, Storing image in Overlay Memory
Application Selection Screen Image Shift Selection Screen (Image Shift mode)
Image Shift Selection Screen (PAGE SPACE selected)
9-34 Applications
Applications
Image Shift (continued)
To Adjust Position of Copy Image (continued)
Right
Up
Down
Right
Left
Up
Original
Down
Left
Copies
1 Select the copy mode and copy size from the Basic Screen, as required.
2 Touch APPLI. on the Basic Screen to enter the Application Selection Screen.
3 Touch Image Shift to display the Image Shift Selection Screen.
4 Touch Image Shift.
To set shift amount in Image Shift:
(1) Touch FRONT, BACK, or BOTH SIDES. When BOTH SIDES is selected, the entered
shift direction and amount will be reflected immediately in the FRONT and BACK
Images on the screen. Touch FRONT or BACK to specify the shift direction and
amount individually.
(2) Touch UP SHIFT, DOWN SHIFT, RIGHT SHIFT, or LEFT SHIFT to specify the shift
direction, then use the touch screen keypad or up/down arrow key to select the
desired shift amount (available range: 0~250mm). Keep touching the arrow key to
increase or decrease the value continuously.
The image display on the screen allows you to view the binding margin to be created
on the printed sheets. The following icons will appear to show the currently selected
conditions.
UP DOWN RIGHT LEFT UP&RIGHT UP&LEFT DOWN&RIGHT DOWN&LEFT
Applications 9-35
Applications
To Adjust Position of Copy Image (continued)
5 When Booklet or 2 Repeat mode of Repeat has been already selected, the PAGE
SPACE key appears clear on the screen to show its availability, with PAGE SPACE
indication displayed in the image area.
If desired, touch PAGE SPACE to highlight it, then enter the desired amount using the
touch screen keypad or up/down arrow key.
6 Touch OK to complete the setting and return to the Application Selection Screen.
7 Select additional Application functions, or touch OK to return to the Basic Screen.
10 Press [Start].
After copying is completed, touch Image Shift on the Application Selection Screen or
9-36 Applications
Applications
To Reduce and Shift Copy Image
Use Reduce & Shift mode instead of regular Image shift to prevent image loss when
creating a binding margin.
❒ Shift amount in Reduce & Shift mode: 0 ~ 250 mm in 1 mm increments (setting in 0.1 mm
increments using up/down arrow key is also available by Key Operator setting.), to be set
collectively for the front and back pages, however, the shift amount for the back page can be
altered in order to position the image exactly the same as on the front page.
❒ In Reduce & Shift mode, AMS is automatically selected and cannot be released.
❒ Original/copy size: 11"x17", 8.5"x14", 8.5"x11", 8.5"x11"R
❒ Incompatible conditions with Reduce & Shift mode
Basic copying conditions: Change magnification, V/H zoom, APS
Special Originals: Mixed Original
Applications: Book Copy, Non-Image Area Erase, Repeat, AUTO Layout, Overlay, Storing
image in Overlay Memory
Front
Left binding margin

Right Left
Up
Originals
Down
Back
Front Back
Top binding margin Right binding margin
Left Right Left Right Left Right
Up
Down
Front Down Back Up Front Back
Applications 9-37
Applications
To Reduce and Shift Copy Image (continued)

Application Selection Screen Image Shift Selection Screen (Reduece & Shift mode)
1 Select the copy mode and copy size from the Basic Screen, as required.
2 Touch APPLI. on the Basic Screen to enter the Application Selection Screen.
3 Touch Image Shift to display the Image Shift Selection Screen.
4 Touch Reduce & Shift.
To set shift amount in Reduce & Shift:
(1) Touch FRONT. In Reduce & Shift mode, the BOTH SIDES key appears grayed to
show inactivity. The message “Select magnification ratio on FRONT side” will be
displayed when BACK is selected first.
(2) Touch UP SHIFT, DOWN SHIFT, or RIGHT SHIFT to specify the shift direction. In
Reduce & Shift mode, the LEFT SHIFT key with FRONT selected appears dimmed to
show inactivity. Use the touch screen keypad or up/down arrow key to select the
desired shift amount (available range: 0~250mm). Keep touching the arrow key to
increase or decrease the value continuously.
The AMS will automatically determine the magnification ratio according to the shift
amount specified for the front page. The shift amount and magnification ratio
determined for the front page will be automatically applied to the back page.
(3) Touch BACK and make direction and amount change, if any positioning adjustment
is required. With BACK selected, the magnification ratio will not be changed, while
the direction and amount can be altered.
5 Touch OK to complete the setting and return to the Application Selection Screen.
6 Select additional Application functions, or touch OK to return to the Basic Screen.
9 Press [Start].
After copying is completed, touch Image Shift on the Application Selection Screen or
9-38 Applications
Applications
Stamp
Stamp allows you to print regular stamp, numbering, page numbering, date and time,
watermark, and watermark numbering onto the output copies. These 6 types of stamps
can be used individually or in multiple combinations.
• STAMP prints the letters selected from 8 options onto the scanned image at the location
designated on the screen.
• SET NUMBERING prints the numbers in the specified form over the scanned image at
the location designated on the screen.
• PAGE NUMBERING prints the page numbers in the specified form over the scanned
image at the location designated on the screen.
• DATE/TIME prints the date and time in the specified form over the scanned image at the
location designated on the screen.
• WATERMARK prints the letters selected from 8 options over the scanned image,
positioning it in the center of the page.
• WATERMARK NUMBERING repeatedly prints the numbers in the specified form over
the scanned image.
❒ All 6 types of stamps can be used in combination.
❒ A watermark is printed obliquely in the center of the page. Watermark numbering prints a number
repeatedly over the scanned image.
❒ Stamp, Set numbering, Page numbering, and Date/Time settings each allow you to select a
printing position from 9 locations.
❒ Stamp, Set numbering, and Date/Time settings each allow you to choose whether to print the
stamp on all pages or on the cover only.
❒ Page numbering allows you to choose whether to print on all pages, on all pages except the front
cover, or on all pages except the front and back covers.
Furthermore, with Sheet/Cover Insertion or Chapter selected, Page numbering allows you to
specify the following option.
COPIED INSERT Print ON : Page number will be printed.
Print OFF : Page number will not be printed but will be counted.
Skip page : Page number will not be printed or counted.
BLANK INSERT Print OFF : Page number will not be printed but will be counted.
Skip page : Page number will not be printed or counted.
❒ When Chapter is already selected, Set numbering, Page numbering, and Watermark numbering
each allow you to print chapter number on each chapter page, in addition to each numbering
function. When used in duplex copying, specified right/left printing position will be automatically
reversed on back pages. When used in duplex copying and top/bottom staple position is selected,
specified top/bottom printing position will be automatically reversed on back pages.
❒ Image cutoff width: leading end 5mm, trailing end 4mm, top and bottom 2mm.
Applications 9-39
Applications
Stamp (continued)
❒ Incompatible Applications: Reverse image, Repeat except 2/4/8 Repeat, Overlay (with STAMP,
SET NUMBERING, WATERMARK, and WATERMARK NUMBERING), Overlay Memory
NOTE: STAMP and WATERMARK are available only with Hard Disk Drive Kit (DL6500020) installed in the
machine. Without HDD, these function keys will be grayed out to show inactivity.
Top-Left T-Middle T-Right TOP SECRET

l
tia
den STAMP
nf i
Co
’00/10/10 10:30AM
Middle-Left Middle M-Right
WATERMARK DATE/TIME
0001/1000
2/5
0001/1000 0001/1000
PAGE NUMBERING
0001/1000
0001/1000 0001/1000 Lower-Left L-Middle L-Right [0002 / 0005]

Positions of other stamps
WATERMARK NUMBERING SET NUMBERING
Application Selection Screen Stamp/Overlay Selection Screen
2 Touch Stamp/Overlay. The Stamp/Overlay Selection Screen will be displayed.
3 Touch to select the desired stamp to display the subsequent screen.
On each screen, you can specify the desired type of the selected stamp.
9-40 Applications
Applications
Stamp (continued)
Stamp Selection Screen Set Numbering Type Selection Screen
Page Numbering Type Selection Screen Date/Time Type Selection Screen
Watermark Selection Screen Watermark Numbering Type Selection Screen
4 When selecting STAMP, SET NUMBERING, PAGE NUMBERING, or DATE/TIME,

select the desired position from 9 location keys on each screen.
If fine adjustment is required, touch FINE ADJ. OF POSITION to display the Fine
Adjustment Setting Screen.
Touch UP SIDE, DOWN SIDE, RIGHT SIDE, or LEFT SIDE to specify the direction, then
use the touch screen keypad or up/down arrow key to enter the desired amount.
Fine Adjustment Setting Screen
Applications 9-41
Applications
Stamp (continued)
5 Touch CHARACTER SIZE, if desired, to change the character size. The following options
are provided:
STAMP : LARGER/ SMALLER
SET NUMBERING : 20pt/ 36pt
PAGE NUMBERING : 8pt/ 10pt/ 12pt/ 14pt
DATE/TIME : 8pt/ 10pt/ 12pt/ 14pt
6 Touch PRINTED PAGE on the Stamp Selection, Set Numbering Type Selection, or Date/
Time Type Selection Screen to designate whether to print the selected stamp on the
cover only or on all pages.
Touch PRINTED PAGE on the Page Numbering Type Selection Screen to display the
Cover/Insert Print Setting Selection Screen.
• When selecting the COVER PRINT SETTING, touch Front & Back: Print ON, Front:
Print OFF and Back: Print ON, or Front & Back: Print OFF.
• When selecting the INSERT PRINT SETTING, touch Print ON, Print OFF, or Skip
page, as provided for each of copied insert and blank insert.
Touch OK to return to the Page Numbering Type Selection Screen. You will find that
the screen reflects the selection you made.
Page Numbering Type Selection Screen
Cover/Insert Print Setting Selection Screeh (with INSERT PRINT SETTING selected)
7 Touch STARTING No. on the Set Numbering, Page Numbering, or Watermark

Numbering Type Selection Screen to display the Starting No. Setting Screen. Use the
touch screen keypad or up/down arrow key to enter the desired starting number, then
touch OK to return to the previous screen.
Use +/– to enter a minus number to print from halfway through, e.g. –2 to print “1” from
page 4.
Original
Starting No. Setting Screen
Copy
1 2
–2 –1 0
9-42 Applications
Applications
Stamp (continued)
When Chapter is already selected, touching STARTING No. on the Set Numbering, Page
Numbering, or Watermark Numbering Type Selection Screen will display the Starting
No. Setting Screen with Chapter starting number setting (see below). Touch CHAPTER
NUMBER or PAGE NUMBER to highlight it, then use the touch screen keypad or up/
down arrow key to enter the desired starting number for each.
Touch OK to return to the previous screen.
Starting No. Setting Screen (with Chapter selected)
8 When selecting WATERMARK or WATERMARK NUMBERING, touch LIGHT, NORMAL,

DARK, or DARK+ to select the desired density level on each screen.
9 When all the desired selections are made, touch OK to return to the Application
Selection Screen.
10 Make additional application selections, or touch OK to return to the Basic Screen.
PAGINATION.
Option: Press [Mode Check] to view selection, and make a Proof copy, if desired. Touch EXIT to return to the
Basic Screen. See p. 6-43 to p. 6-45.
13 Press [Start].
After copying is completed, touch Stamp/Overlay on the Application Selection Screen
or press [Panel Reset] to release the mode and reset the machine.
Applications 9-43
Applications
Overlay
Use Overlay to scan an image and overlay the image onto each page copied in the job.
❒ Scan and store originals into memory.
❒ APS and AMS are automatically released.
❒ Magnification is initially set to 1:1. This setting is changeable.
❒ Incompatible Basic Copying Conditions: Rotation, Rotation Sort, Rotation Group
❒ Incompatible Applications: Sheet/Cover Insertion, Combination, Transparency Interleave, Image
Insert, Book Copy, Program Job, Repeat, AUTO Layout, Reduce & Shift in Image Shift, STAMP,
SET NUMBERING, WATERMARK, WATERMARK NUMBERING
Originals scanned Copies in OVERLAY mode

1st scanned original 2nd and later
ABCD ABCD
ABCD
ABCD
3 Touch OVERLAY to highlight it.
6 The Store mode is automatically selected, and APS and AMS are released.
Set the desired Copy mode, Copy density, Lens mode, and Copy size on the Basic
Screen.
9-44 Applications
Applications
Overlay (continued)

8 Position the overlaying original in the EDH or on the platen glass, then press [Start] to
scan.
9 The second and subsequent pages are to be overlaid in printing.
Place them in the EDH or on the platen glass, then press [Start].
IMPORTANT: PLACE AND SCAN THE ORIGINALS IN REGULAR ORDER OF PAGINATION.
Applications 9-45
Applications
Overlay Memory
Use Overlay Memory to scan and store several images in HDD*, then recall the desired
image from the HDD to overlay onto each page copied in the job.
* Installation of the optional Hard Disk Drive Kit (DL6500020) is required.
Image Store
ABCD
HDD
Store in HDD
Overlaying image
Recall overlaying image
Output
ABCD
ABCD ABCD
ABCD
Output
Recalled image
Overlay originals Copies in Overlay Memory mode
To Store Overlaying Image Data in HDD

The following procedure describes how to store overlaying image data in HDD.
❒ Use the platen glass only.
❒ Copy mode: 1-1 mode only
❒ Incompatible Basic Copying Conditions: Using EDH, 1-2, 2-2, 2-1, AMS, Rotaion, Reserve Mode,
Interrupt Mode, Selecting Output Mode
❒ Incompatible Special Originals: Mixed Original, Z-Folded Original, Tab Paper
Interleave, Image Insert, Book Copy, Program Job, Non-Image Area Erase, Reverse Image,
Repeat, AUTO Layout, Image Shift, Stamp, Overlay
9-46 Applications
Applications
Overlay Memory (continued)
To Store Overlaying Image Data in HDD (continued)

3 Touch OVERLAY MEMORY to display the Overlaying Image Selection Screen.
NOTE: Without HDD, the OVERLAY MEMORY key will be dimmed on the Stamp/Overlay Selection Screen to
show inactivity.
4 Touch IMAGE STORE to display the Image Name Entry Screen.
Overlaying Image Selection Screen Image Name Entry Screen
5 Enter the desired image name in up to 8 characters from the touch screen keypad. The
date when you made this entry will be stored automatically.
To correct an entry, touch 1-CHARACTER DELETE repeatedly to delete each character,
then enter the correct image name.
6 If the image name is correct, touch OK. The Basic Screen to store the overlaying image
will be displayed.
If the popup menu with YES and NO keys is displayed instead of the Basic Screen, the
entered name is duplicated. Touch YES to enter a new name, or NO to create a duplicate
name.
If the popup menu with OK key is displayed, the entered name is duplicated. Touch OK,
then enter a new name.
If the IMAGE DELETE key is displayed on the Overlay Image Selection Screen, you can
delete the stored image and name. Select the image name using up/down arrow key to
scroll, then touch IMAGE DELETE.
NOTE: Changing the popup menu for duplicate name and displaying the IMAGE DELETE key is available in
the Memory switch No. 45 of the Key Operator setting. See p. 13-43 ~ p. 13-49.
Applications 9-47
Applications
To Store Overlaying Image Data in HDD (continued)

Image Name Entry Screen Image Name Entry Screen
Basic Screen to store overlaying image Overlaying Image Data Storing Screen
7 Position the overlaying original on the platen glass, then press [Start] to scan.
NOTES: • The EDH cannot be used for storing the overlaying image.
• To stop scanning, press [Stop].
8 After scanning the overlaying original, the Overlaying Image Data Storing Screen will be
displayed. The machine automatically starts to store the overlaying image data in the
HDD. The Overlaying Image Selection Screen will resume when the storing function is
completed.
To continue to store the overlaying image data, return to step 4.
9 Touch OK to return to the Stamp/Overlay Selection Screen.
9-48 Applications
Applications
To Overlay Image Stored in HDD
The following procedure describes how to overlay the image stored in HDD onto each
page copied in the job.
❒ APS and AMS are automatically released.
❒ Magnification is initially set to 1:1. This setting is changeable.
❒ Incompatible Applications: Reverse Image, STAMP, SET NUMBERING, WATERMARK,
WATERMARK NUMBERING in Stamp
3 Touch OVERLAY MEMORY to display the Overlaying Image Selection Screen.
NOTE: Without HDD, the OVERLAY MEMORY key will be dimmed on the Stamp/Overlay Selection Screen to
show inactivity.
Overlaying Image Selection Screen
4 Select the desired overlaying image data to highlight it. Use up/down arrow key to scroll,
if needed.
5 Touch OK to return to the Stamp/Overlay Selection Screen.
Applications 9-49
Applications
To Overlay Image Stored in HDD (continued)

8 The Store mode is automatically selected, and APS and AMS are released.
Set the desired Copy mode, Copy density, Lens mode, and Copy size on the Basic
Screen.
10 Place originals in the EDH or on the platen glass, then press [Start] to scan.
PAGINATION.
9-50 Applications
DL650us10v1.fm 1 ページ２００１年１１月１４日　水曜日　午後３時２５分
Section 10: Program Memory
Job Store
Job Recall
Program Memory Form
Program Memory 10-1

Program Memory
Job Store
Use Job Store to store up to 30 frequently-used copying jobs, which can be recalled at any
time. The stored jobs can be given alphabetical names.
❒ All copying functions can be selected
Control panel Job No. Selection Screen

Help
Program Memory
Mode Check
Utility
Proof Copy
Job Store Check Screen
Job Name Registration Screen
10-2 Program Memory

Program Memory
Job Store (continued)
1 Make job selections from the Basic Screen, Application Selection Screen, Special
Original Screen and/or Output Selection Screen.
2 When all selections are made, press [Program Memory] on the Control panel to display
the Job No. Selection Screen.
3 Touch STORE. The Job Store Check Screen displays to enable you to review the
settings. (See sample Job Store Check Screen, previous page.)
4 If settings are correct, touch OK to restore the Job No. Selection Screen.
Otherwise, touch CANCEL to return to the Basic Screen, and make new selections.
5 When the Job No. Selection Screen is restored, touch one of the keys numbered from
1~30 to store the job under that number. The key with a lock icon ( ) displayed is locked
and cannot be selected. Arrow keys can be used to scroll to the next/previous page. The
selected number key will be highlighted.
6 Touch OK on the Job No. Selection Screen to display the Job Name Registration
Screen.
If you do not wish to enter a name, touch OK.
7 Enter a job name in up to 16 characters, using the touch screen alphabet keypad.
To correct an entry, touch DELETE repeatedly to delete each character entered, then
enter the correct job name.
8 If the Job name is correct, touch OK to resume the Job No. Selection Screen.
To re-enter the Job name, touch CANCEL to return to the Job No. Selection Screen.
9 When the Job No. Selection Screen is displayed, touch OK to complete the setting and
return to the Basic Screen.
To re-enter the Job name when the Job No. Selection Screen is displayed, touch
CANCEL to display the Job Name Registration Screen.
To exit from the Program Memory setting anytime, press [Panel Reset].
NOTES:
1 A locked job is indicated by a lock icon on the Job key number.
2 Only the Key Operator can lock a job.
3 A locked job cannot be overwritten unless it is unlocked by the Key Operator.
4 A blank key indicates that no job is stored under that key.
5 Program Memory entries can be recorded on the Program Memory Form included at the end of this section.
Program Memory 10-3

Program Memory
Job Recall
Use Job Recall to recall jobs that are already stored in Program Memory.
Job No. Selection Screen
Job No. Selection Screen (Job Recall)
Job Recall Check Screen
10-4 Program Memory

Program Memory
Job Recall (continued)
1 Place original(s) as required for the job you are about to recall.
2 Press [Program Memory] to display the Job No. Selection Screen.
(See sample screen, previous page.)
3 Touch a Job No. key to select a job you want to recall, and to highlight the key.
If required, scroll with the arrow keys to reach the desired Job No. key (1~30).
To cancel the recall mode, touch CANCEL to return to the Basic Screen.
4 Touch JOB CHECK. The Job Recall Check Screen displays to enable you to review the
settings. Touching CANCEL on the Job Recall Check Screen returns to the Job No.
Selection Screen.
(See sample Job Recall Check Screen, previous page.)
5 When the desired Job No. key is highlighted, touch OK to read the settings of the
selected job, and to return to the Basic Screen.
To cancel the job, press [Panel Reset].
6 Press [Start].
NOTES:
1 A locked job is indicated by a lock icon on the Job key number.
2 Only the Key Operator can lock a job.
3 A locked job cannot be overwritten unless it is unlocked by the Key Operator.
4 A blank key indicates that no job is stored under that key.
5 Program Memory entries can be recorded on the Program Memory Form included at the end of this section.
Program Memory 10-5

Program Memory
Program Memory Form
Make a copy of this form to record frequently-used copy jobs stored in Program Memory.
Update the information when changes are made. Make additional copies, as needed.
JOB NUMBER/NAME JOB DESCRIPTION
10
11
12
13
14
15
10-6 Program Memory

Program Memory
Program Memory Form (continued)
JOB NUMBER/NAME JOB DESCRIPTION
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
Program Memory 10-7

DL650us11v1.fm 1 ページ２００１年１１月１４日　水曜日　午後３時２８分
Section 11: Server Function
Server Function
Image Store/Delete Mode
To Store Image Data in HDD
To Delete Image Data
Image Store & Output Mode

Image Recall Mode
Server Function 11-1

Server Function
Server Function
Use Server function to accumulate scanned images into built-in DIMM (memory), then
store the image data in HDD (option) so that the data can be recalled to DIMM and output
as needed. This function also allows you to store the image data for normal copying
procedures.
NOTE: Installation of the optional Hard Disk Drive Kit (DL6500020) is required for the Server function.
Scan
Output
DIMM
Store Recall
HDD
Server Function
The Server function provides the following three modes:

q Image Store/Delete mode
Store the image data scanned from originals in HDD, or delete the data stored in HDD.
.
11-2 Server Function

Server Function
Server Function (continued)
w Image Store & Output mode

Store the scanned image data in HDD after copying is completed.
e Image Recall mode

Recall the image data stored in HDD to built-in DIMM for printing.

Server Function
Image Store/Delete Mode
When the original image is stored into DIMM, use this function to store the image data into
HDD. In the event data is already stored in HDD, use this function to delete it from HDD.
NOTE: Installation of the optional Hard Disk Drive Kit (DL6500020) is required for storing data in the HDD.
To Store Image Data in HDD

Specify your password when storing the data in HDD for protection. Image data can be
given an alphabetical job name.
❒ Incompatible Basic Copying Conditions: 1-2, 2-2, AMS, Selecting output mode, Selecting copy
size (APS is automatically selected), Setting print quantity, Rotation
❒ Incompatible Special Originals: WHOLE AREA in Non STD Size
Interleave, Image Insert, Book Copy, Program Job (available in Image Store & Output Mode only),
Non-Image Area Erase, Reverse Image, Repeat, AUTO Layout, Image Shift, Stamp/Overlay
Control Panel Scan/Server Setting Menu Screen

Print Copy Scan
Energy Saver
Timer
Interrupt
Panel Reset

Server Function
Image Store/Delete Mode (continued)
To Store Image Data in HDD (continued)

Scan/Server Setting Menu Screen Image Data Password Entry Screen
Job Name Entry Screen Scanner Setting Screen
1 Press [Mode] to light up the [Scan] LED. The Scan/Server Setting Menu Screen will
display.
2 Touch IMAGE STORE/DELETE. The Image Data Password Entry Screen will be
displayed.
3 Enter the desired image data password in up to 8 characters from the touch screen
keypad.
then enter the correct password.
4 If the password is correct, touch OK to display the Job Name Entry Screen.
Enter the desired job name in up to 8 characters from the touch screen keypad.
then enter the correct job name.
5 If the job name is correct, touch OK to display the Scanner Setting Screen.
6 Select the desired scanning conditions. Print quantity cannot be entered.
8 Press [Start] to scan original(s).
When scanning is completed, the Image Data Storing Screen will be displayed.

Server Function
To Store Image Data in HDD (continued)
When store mode is used, touch to deselect STORE on the Scanner Setting Screen
after all originals are scanned. The Image Data Storing Screen will be displayed.
9 The machine automatically begins storing data in the HDD. The Basic Screen displayed
“SCANNER ➔ HDD” icon resumes when the storing function is completed.
Image Data Storing Screen (popup menu displayed
NOTE: To suspend the storing job, touch CANCEL on

the Image Data Storing Screen. If the popup
menu shown below is displayed, touch YES to
delete the data, or touch NO to continue. The
popup menu displays when the Memory Switch
No. 43 is turned on in the Key Operator Mode.
See p. 13-43 to p. 13-49.

Server Function
To Delete Image Data
Job Name Entry Screen Job Name Entry Screen (popup menu displayed)
1 Press [Mode] to light up the [Scan] LED. The Scan/Server Setting Menu Screen will be
displayed.
2 Touch IMAGE STORE/DELETE. The Image Data Password Entry Screen will be
displayed.
3 Enter your Image data password from the touch screen keypad.
5 Touch the ▲ or ▼ key on the right side of the job name list to highlight the name of the
data to be deleted, then touch JOB DELETE. The popup menu will appear to confirm
that you delete the selected data.
6 Touch YES to delete it, or touch NO to cancel. The popup menu will disappear.
7 Touch OK to restore the Scan/Server Setting Menu Screen.
8 Press [Mode] to light up the [Copy] LED. The Basic Screen will be displayed.

Server Function
Image Store & Output Mode
Use this function to store the scanned image data in HDD after copying is completed.
This storing function does not conflict with any other copying conditions.
NOTE: Installation of the optional Hard Disk Drive Kit (DL6500020) is required for this function. With the HDD
installed, the HDD STORE key will be displayed on the Output Mode Screen.
Output Mode Screen (with Finisher) Output Mode Screen (without Finisher)
Image Data Password Entry Screen Job Name Entry Screen
2 Touch HDD STORE. The Image Data Password Entry Screen will be displayed.
3 Enter the desired Image data password in up to 8 characters from the touch screen
keypad.
Enter the desired job name in up to 8 characters from the touch screen keypad.
then enter the correct job name.
5 If the job name is correct, touch OK twice to return to the Basic Screen.
6 Select the desired copying conditions, then enter the desired print quantity.
While using Program job, the scanned and output data can be stored in HDD. See p. 9-
22.

Server Function
Image Store & Output Mode (continued)
8 Press [Start] to scan and then print.

When the Store mode is used, touch STORE on the Basic Screen to deselect the Store
mode when the store function is completed, i.e., after all originals are scanned, then
press [Start] to print.
NOTE: To suspend the scanning or printing job, press [Stop] on the control panel. The popup menu will be
displayed to ask you how to complete the current job. Touch CONTINUE to continue the job, EXIT to
cancel the job and delete the data, or EXIT after storing data to HDD to store the data in HDD
without printing.
Basic Screen
9 After scanning all the originals, the machine automatically starts to output and store the
data in HDD. The Basic Screen displayed “SCANNER ➔ HDD” icon will resume when
completed.

Server Function
Image Recall Mode
Use this function to recall the image data from the HDD to the built-in DIMM for printing.
NOTE: Installation of the optional Hard Disk Drive Kit (DL6500020) is required to recall data from HDD.
To recall data stored in the HDD, enter the password specified at the time data was stored,
then designate it by the job name.
Recall Job Selection Screen
1 Press [Mode] to light up the [Scan] LED.

The Scan/Server Setting Menu Screen
will be displayed.
2 Touch IMAGE RECALL to display the
Image Data Password Entry Screen.
3 Enter your Image data password from the
touch screen keypad.
4 If the password is correct, touch OK to display the Recall Job Selection Screen.
5 Touch the desired job name key to highlight it, then touch a to move it to the recall list
on the right side. Touching JOB CHECK displays the Check Screen to allow you to view
all the feature selections made for that job.
NOTE: More than one job at a time can be moved to the recall list to be output in succession, provided that
those jobs have been stored with the same copying conditions.
To cancel the job moved to the recall list, touch the job name in the list to highlight it, then touch b to
return it to the left side key.
6 If the desired job name is displayed in the recall list, touch WAIT OUTPUT, PROOF
OUTPUT, or AUTO OUTPUT, as desired. Follow the procedure below according to the
selected output mode key to complete the image recall and output operation.

Server Function
Image Recall Mode (continued)
Selecting WAIT OUTPUT:

(1) Touch OK. The Image Data Recalling Screen will be displayed to show the current
status of transmission.
When the data transmission is completed, the Basic Screen will be displayed
reflecting the settings made for that job.
(2) Enter the desired print quantity, then press [Start] to print.
Mode Check Screen
Selecting PROOF OUTPUT:
(1) Touch OK. The Basic Screen is
restored, and the data is transmitted.
When the data transmission is
completed, the Mode Check Screen
will be displayed after a set of sample
copy is output.
(2) Check the sample copy, then change the copy conditions if required.
Enter the desired print quantity, then press [Start] to print.
Recall Job Selection Screen (popup menu displayed)
Selecting AUTO OUTPUT:
(1) Touch OK. The popup menu to enter
the print quantity will be displayed.
(2) Enter the desired print quantity, then
touch OK.
The Image Data Recalling Screen will
be displayed to show the current
status of transmission.
When the data transmission is completed, the machine automatically starts to print.
NOTE: To suspend recall while the Image Data Recalling Screen is displayed, touch CANCEL. If the popup
menu shown below is displayed, touch YES to delete the data recalled to DIMM, or touch NO to continue.
The data stored in HDD will not be erased by this operation.
The popup menu displays when the Memory Switch No. 43 is turned on in the Key Operator Mode. See
p. 13-43 to p. 13-49.
Image Data Recalling Screen (popup menu displayed) Image Data Recalling Screen (popup menu displayed)

DL650us12v1.fm 1 ページ２００１年１１月１４日　水曜日　午後３時３２分
Section 12: Shortcuts
Set Reserve Job

Store Originals Scanned from Platen
Store Originals Scanned from EDH
Stapling & Folding, and Folding
Mixed Original
Chapter
Combination
Booklet
Image Insert
Book Copy
Program Job
Reverse Image
Repeat Image
Frame/Fold Erasure
AUTO Layout
All-Image Area
Image Shift/ Reduce & Shift
Stamp/Overlay
Loading Paper
Adding Toner
Shortcuts 12-1
Shortcuts
Set Reserve Job (p. 6-28)

1 Touch FREE JOB to display the Reserve job setting screen while a current job is in
progress.
2 Select copying conditions for the reserve job. Wait for the current job to complete its
scanning operation, if necessary.
3 Position the Reserve job original(s) face up on the EDH (Electronic Document
Handler) tray or face down on the platen glass.
4 Press [Start] to scan the Reserve job original(s).
When scanning for the Reserve job is completed, the Basic screen for the current
printing job will be restored.
Copying for the reserve job will start when the current job is completed.
Store Originals Scanned from Platen (p. 6-35)

1 Position the original on the platen glass.
2 Make desired copying selections, and select the 1-1 or 1-2 copy mode.
3 Touch STORE on the Basic screen to highlight the Store mode.
4 Press [Start] to scan and store the original image into memory.
Repeat Steps 1 and 4 until all originals are scanned.
6 Enter the print quantity amount.
7 Press [Start] to begin copying.
Store Originals Scanned from EDH (P. 6-37)

1 Touch STORE on the Basic screen to highlight the Store mode.
2 Make desired copying selections.
3 Position no more than 100 originals at a time on the EDH (Electronic Document
Handler) tray.
5 Press [Start] to scan the originals.
Repeat Steps 3 and 5 until all originals are scanned.
7 Press [Start] to begin copying.
NOTES:
1. Page numbers indicated next to each Shortcut refer to the pages of the Operating Manual where more detailed
information can be found.
2. When using Platen Store mode or EDH Store mode in conjunction with other functions, check details on p. 6-
35 and p. 6-37, respectively.
12-2 Shortcuts
Shortcuts
Stapling & Folding, and Folding (p. 7-13)

1 Close the EDH (Electronic Document Handler cover), then press [Panel Reset] to
reset the machine.
2 Touch OUTPUT APPLI. to display the Finisher mode selection screen.
3 Touch STAPLING & FOLDING to select the Stapling & Folding mode, or touch
FOLDING to select the Folding mode.
4 Touch OK to display the Basic screen.
5 Make additional copying selections.
7 Position originals on the EDH tray.
8 Press [Start]. When copying is completed, press [Panel Reset] to reset the machine.
Mixed Original (p. 8-6)
1 Touch SPECIAL ORIGINAL to display the Special original screen.
2 Touch Mixed Original.
4 Touch OK to return to the Basic screen.
5 Select APS to copy on various sizes to match the originals, or select AMS mode to
copy on one size.
7 Position mixed originals face up on the EDH (Electronic Document Handler) tray.
Combine ledger, legal, letter, 5.5"x8.5"/or legal, letter R, letter.
Sheet/Cover Insertion (p. 9-3)
1 Touch APPLI. to display the Application selection screen.
2 Touch Sheet/Cover Insertion to display the Sheet/Cover insertion screen.
3 If desired, touch FRONT COPY or FRONT BLANK.
If desired, touch BACK COPY or BACK BLANK.
4 If desired, touch COPY INSERTION or BLANK INSERTION.
Enter the page number for the first insertion location, then touch SET.
5 Repeat Step 4 for each insertion location, touching SET after each entry.
6 Select the desired tray source for the cover and/or insertion sheets.
7 Touch OK to return to the Application selection screen.
11 Position originals face up on the EDH (Electronic Document Handler) tray.
Shortcuts 12-3
Shortcuts
Chapter (p. 9-8)

2 Touch Chapter to display the Chapter page setting screen with 1-2 mode automatically
selected.
3 Use the keypad to enter the page number of the first title page, then touch SET.
4 Repeat Step 3 for each additional title page, touching SET after each entry.
9 Position (up to 100) originals face up on the EDH (Electronic Document Handler) tray.
Combination: Copy 2, 4 or 8 originals on 1 sheet (p. 9-10)
2 Touch Combination to display the Combination mode selection screen.
3 Touch 2 in 1, 4 in 1, or 8 in 1.
6 Touch OK to return to the Basic screen with AMS automatically selected. You may
change this setting.
7 When all settings are correct, enter the print quantity amount.
8 Place original(s) face up on the EDH (Electronic Document Handler) tray.
Booklet (p. 9-12)
2 Touch Booklet to display the Booklet mode selection screen.
3 Touch NO COVER SHEET, COVER WITH COPY SHEET, or COVER WITH BLANK SHEET.
4 Select the cover sheet tray source and the binding mode, if required.
6 Make additional copying selections, or touch OK to return to the Basic screen.
7 Select 1-2 or 2-2 copy mode. To release AMS default, select magnification and copy
size.
8 Touch OUTPUT APPLI. to select folding or stapling & folding if the 9922 Finisher is
installed.
9 Touch OK to restore the Basic screen, then enter the print quantity amount.
10 Position letter-size originals face up on the EDH (Electronic Document Handler) tray, in
crosswise orientation.
12-4 Shortcuts
Shortcuts
Transparency Interleave (p. 9-15)

1 First, load the same size copy paper as the transparencies in any regular tray.
2 Insert one transparency sheet at a time into the Multi-sheet bypass tray.
4 Touch Transparency Interleave to display the Transparency interleave screen.
5 Touch Blank Sheet Interleaving or Copy Sheet Interleaving, unless your choice is
already highlighted.
7 Make additional selections.
8 Touch OK to return to the Basic screen with the required print quantity of [1]
automatically selected.
9 Position the original face up on the EDH (Electronic Document Handler) tray or face
down on the platen glass.
Image Insert (p. 9-17)
1 In preparation, note the page number locations of the images you will be scanning
from the platen glass.
3 Touch Image Insert to display the Image insertion number setting screen.
4 Enter up to 30 page number locations, touching SET after each entry.
5 When all page number locations are entered, touch OK to restore the Application
selection screen.
6 Make additional copying selections, or touch OK to return to the Basic screen. The
Store mode is automatically selected.
7 To start scanning, position the regular originals face up on the EDH tray, then press
[Start].
8 After the originals on the EDH (Electronic Document Handler) tray are scanned, enter
the print quantity amount for the job.
9 Position one original at a time on the platen glass in ascending order of pagination,
i.e., 1~n.
The platen glass originals can be paste-ups, graphs, photos, newspaper articles, or
any non-standard document.
10 In turn, press [Start] to scan each original from the platen glass.
12 Press [Start] to combine the non-standard images scanned from the platen glass with
the regular images scanned from the EDH (Electronic Document Handler). When
copying is completed, press [Panel Reset] to reset machine.
Shortcuts 12-5
Shortcuts
Book Copy (p. 9-19)

1 First, load letter sheets in a regular tray or in the Multi-sheet bypass tray.
3 Touch Book Copy to display the Book copy screen with AUTO layout and Non-image
area erase selected.
4 Touch Full scan, Front cover + Full scan, or Front/Back cover + Full scan, as required.
To change the binding mode, touch REVERSE THE SIDE OF OPEN PAGE.
7 Touch OK to return to the Basic screen with the Store mode automatically selected.
8 Select 1-1 or 1-2 copy mode and enter the print quantity amount.
9 Position the open book in the right rear corner on the platen glass.
10 Align the edges of the book with the left measuring guide plate, then press [Start] to
begin scanning.
11 Repeat Steps 9 to 10 to copy subsequent pages from the book, pressing [Start] to
scan each page.
Program Job (p. 9-21)
2 Touch Program Job to scan multiple sets of originals in different settings (called JOBs)
and then to output them all as a complete set.
3 Make additional copying selections for the first JOB.
4 Touch OK to return to the Basic screen. Store mode is automatically selected.
5 Position original(s) face up in the EDH (Electronic Document Handler) or face down on
the platen glass, select the tray you want to use, then press [Start] to scan.
6 When scanning for the current JOB is completed, the popup menu will be displayed.
To store the current JOB images, touch DECISION.
To delete the images, touch CANCEL.
7 Repeat steps 3 to 6 until all JOB originals are scanned.
8 Select the desired output mode and enter the print quantity amount.
Non-Image Area Erase (p. 9-23)
2 Touch Non-Image Area Erase.
6 Position original face down on the platen glass, keeping the EDH (Electronic
Document Handler cover) open.
12-6 Shortcuts
Shortcuts
Reverse Image (p. 9-25)

2 Touch Reverse Image to switch from the black-on-white copying mode to white-on-
black copying.
6 Position original(s) face up on the EDH (Electronic Document Handler) tray or face
Repeat Image (p. 9-26)
2 Touch Repeat to display the Repeat mode selection screen.
3 Touch Vertical/Horizontal to select the mode, then specify the vertical and horizontal
widths of the scanning area using up/down arrow key, or touch ENTER REPEAT WIDTH
BY KEYPAD to display a popup screen to enter a value from the touch screen keypad.
Touch AUTO to allow the machine to set the equal repeat area according to the size of
the original placed onto the platen glass with non-image area erase functioning.
Touch 2 Repeat, 4 Repeat, or 8 Repeat to allow the max. repeats according to the size
of the original.
8 Position original(s) face down on the platen glass.
If you selected the AUTO or 2/4/8 Repeat, keep the EDH (Electronic Document Handler
cover) open during copying.
Frame/Fold Erasure (p. 9-29)
2 Touch Frame/Fold Erasure to display the Frame/Fold erasure selection screen.
3 Touch Frame Erasure (All sides) or Frame Erasure (Each side), then enter a value or
use the default setting.
4 Touch Fold Erasure, then enter a value or use the default setting.
5 Touch OK to complete the setting and return to the Application selection screen.
7 Select copy size and enter the print quantity amount.
Shortcuts 12-7
Shortcuts
AUTO Layout (p. 9-31)

2 Touch AUTO Layout to center the original image on the copy paper.
5 Position original face up in the EDH (Electronic Document Handler) or face down on
the platen glass without skewing it. When using platen glass, DO NOT CLOSE the
EDH (Electronic Document Handler cover).
All-Image Area (p. 9-33)

2 Touch All-image Area if you wish to copy the image completely to the edges of the
paper.
Image Shift/ Reduce & Shift (p. 9-34)

1 First, select a copy mode (1-1, 1-2, 2-1, 2-2) and a copy size from the Basic screen.
3 Touch Image Shift to display the Image shift selection screen.
4 Touch Image Shift (or Reduce & Shift, if image loss is likely).
5 Touch FRONT, BACK, or BOTH SIDES to indicate the side(s) on which you want the
shift to occur.
When Booklet or 2 Repeat mode of Repeat has been selected, the PAGE SPACE
setting is available.
6 Touch UP SHIFT, DOWN SHIFT, RIGHT SHIFT, or LEFT SHIFT to specify the shift
direction.
7 Use the touch screen keypad to enter the shift amount , from 0 ~ 250 mm.
12-8 Shortcuts
Shortcuts
Stamp/ Overlay (p. 9-39/ p. 9-44)

2 Touch Stamp/Overlay to display the Stamp/Overlay selection screen.
3 Touch the desired stamp (STAMP, SET NUMBERING, PAGE NUMBERING, DATE/
TIME, WATERMARK, and WATERMARK NUMBERING) to display the subsequent
screen.
On each screen, you can specify the desired stamp type of the selected stamp.
4 Specify the desired position, size, etc., according to the options provided on each
screen, then touch OK to return to the Stamp/Overlay selection screen.
5 The Overlay function will be selected simply by touching OVERLAY to highlight it.
8 When Overlay is selected, the Store mode is automatically selected, and APS and
AMS are released. Set the desired Copy mode, Copy density, Lens mode, and Copy
size, then enter the print quantity amount.
9 Position original(s) FACE UP in EDH (Electronic Document Handler) or FACE DOWN
on platen glass.
When Overlay is selected, follow the scanning procedure below.
(1) Position the overlaying original in the EDH (Electronic Document Handler) or on
the platen glass, then press [Start] to scan.
(2) The second and subsequent pages are to be overlaid in printing. Place them in the
EDH (Electronic Document Handler) or on the platen glass, then press [Start].
PAGINATION.
(3) When scanning job is completed, touch STORE to remove its highlight and thus
turn off the Store mode.
Shortcuts 12-9
Shortcuts
Loading Paper (p. 14-2)

Main Body User-Adjustable Trays: Tray 1 (500), Tray 2 (500), and Tray 3 (1,500)
1 Withdraw the main body tray, then place paper into the tray with the curl turning up.
Load size 11"x17", 8.5"x14", 8.5"x11", 8.5"x11"R or 5.5"x8.5" (crosswise).
Do not stack paper above the level of the red line.
2 Move the green levers located at the front and left side until they meet the edge of the
stack of paper.
3 When paper is seated properly, push the tray back fully into the copier.
LCC (Large Capacity Cassette: 9930/9932) Service-Adjustable Tray 4 (4,000)

1 Open the LCC top door (lift lid).
2 Press the Paper loading button located at the front of the LCC to lower the bottom
plate of the LCC.
3 Load the fixed size paper into the LCC with the paper curl turning down (see note).
4 Repeat Steps 2 and 3 until the bottom plate cannot go down any more.
Do not stack paper above the paper hook level.
5 When the stack of paper is seated properly in the tray, close the LCC top door (lid).
NOTE: When loading tabbed sheets, be sure the tab extensions are positioned at the rear side of the tray (not at
the front where the Paper load button is located), and jutting to the right, away from the hinged side of the
LCC cover.
Adding Toner (p. 14-7)
CAUTION
Keep toner cartridge away from children. Although the toner is non-toxic, do not inhale it or allow it to
enter your eyes. In case the toner comes in contact with eyes, please consult your physician.
1 Open the toner access door and pull the toner cartridge holder lever forward.
2 Withdraw the toner cartridge holder, then remove the empty toner cartridge.
3 Shake the new toner cartridge several times to loosen toner, then remove the
cartridge cap.
4 Set the new toner cartridge into the toner cartridge holder, aligning the rear part of the
cartridge with the toner cartridge holder.
5 Push the toner cartridge holder lever backward, then return the toner cartridge holder
to its original position.
6 Close the toner access door.
NOTE: Use the toner cartridge of the same number as the number described on the label of a toner access door
inner side, otherwise the machine trouble may occur.
12-10 Shortcuts
DL650us131v1.fm 1 ページ２００１年１１月１４日　水曜日　午後３時３４分
Section 13 : Key Operator Mode

To the Key Operator
How to Access the Key Operator Mode
Function Menu Map
System Initial Setting [1]
Date & Time Setting [1]
Language Select Setting [2]
IP Address Setting [3]
E-Mail Transmission Setting [4]
Copier Initial Setting [2]
User Setting Mode [3]
User Density Level 1 Setting [1]
User Lens Mode Ratio Setting [3]
ECM (Electronic Copy Monitor) Function Setting [4]
How to Access the ECM Setting Mode
E.C.M. Data Edit [1]
E.C.M. All Count Reset [2]
E.C.M. Function Setting [3]
Lock / Delete Program Memory [5]
Paper Type / Special Size Set [6]
Panel Contrast / Key Sound Adjustment [7]
Key Operator Data Setting [8]
Weekly Timer [9]
How to Access the Weekly Timer Setting Mode
Weekly Timer On/Off Setting [1]
Timer Setting [2]
Timer Action On/Off Setting [3]
Lunch Hour Off Setting [4]
Timer Interrupt Password Setting [5]
Control Panel Adjustment [10]
Tray Auto Select Setting [11]
Energy Saver Setting [12]
Memory Switch Setting [13]
Machine Management List Print [14]
Call Remote Center [15]
Side 2 Lens Adjustment [16]
Finisher Adjustment [17]
HDD Management Setting [18]
Non-Image Area Erase Setting [20]
Key Operator ECM Form
Key Operator Mode 13-1

Key Operator Mode
To the Key Operator
The Key Operator is trained to handle all special Key Operator functions that are not
accessible to the general user, such as monitoring overall copier activity, machine
performance, and service information, modifying machine settings as well as controlling
user activity for billing purposes.
A unique 4-digit Key Operator password is normally set by your service representative at
installation. If the unique code is not set by your service representative, the copier will not
display Key Operator Password Entry Screen when the Key Operator mode is being
accessed; a Key Operator password will not be required. A service-set 8-digit ECM master
key code must be entered by the Key Operator to access the Electronic Copy Monitor
functions, and a service-set 4-digit Weekly Timer master key code must be entered by the
Key Operator to access the Weekly Timer functions.
To ensure the security of Key Operator mode, it is recommended that you establish a
unique Key Operator password, along with the Key Operator ECM master key code
and Weekly Timer master key code, and keep them in a confidential file.
❒ Help mode is unavailable in the Key Operator mode
Help Screen Key Operator Password Entry Screen
Key Operator Mode Screen 1 Key Operator Mode Screen 2
13-2 Key Operator Mode

Key Operator Mode
To the Key Operator (continued)
How to Access the Key Operator Mode
1 Press the [Help] button on the Control panel to display the Help Screen.
2 Touch the Key Operator Mode on the Help Screen.
The Key Operator Password Entry Screen displays when the 4-digit Key Operator
password is set by your service representative.
Otherwise, the Key Operator Mode Screen displays without the password requirement.
3 If the Key Operator Password Entry Screen is displayed, use the keypad on the touch
screen to enter your 4-digit Key Operator password. Touch OK to display the Key
Operator Mode Screen. (See note.)
If the Key Operator password is not valid, check with your service representative.
4 To display menus [11] to [20] of the Key Operator Mode Screen, touch the lower arrow
key.
To return the menu [1] to [10] of the Key Operator Mode Screen, touch the upper arrow
key.
5 Make setting changes from the Key Operator Mode Screen, as described on the
following pages.
NOTE: If an invalid password is entered, enter the valid 4-digit password.

Key Operator Mode
Function Menu Map
FUNCTION MENU SUB FUNCTION MENU AND SETTING OPTIONS

[1] System initial setting [1] Date&Time setting: [Present time; Setting time; Summer
time ON/OFF; Difference in time]
[2] Language select setting: [American English]
[3] IP address setting: [IP address; Subnetmask; Gateway
address; Line speed]
[4] E-Mail Transmission Setting: [IP address; E-mail (machine
manager); E-mail (condition inform); E-mail transmission item]
[2] Copier initial setting Copy mode: [EDH; 1-1; 1-2; 2-1; 2-2]
Copy density: [AES; manual]
Lens mode: [AMS; ratio 0.250~4.000]
Copy size: [APS; trays 1, 2, 3, LCC, or Multi-sheet bypass
tray]
Output: [Output appli.; Staple-sort; Sort]
Function: [Special original; Rotation off]
[3] User setting mode [1] User density level 1 setting: [darker / lighter 16 levels]
[2] User density level 2 setting: [darker / lighter 16 levels]
[3] User lens mode ratio setting: [Custom 1; Custom 2;
Custom 3 (ratio 0.250 ~ 4.000)]
[4] E.C.M. Function [1] E.C.M. data edit: [Change; Add; Delete; Count reset]
setting [2] E.C.M. all count reset: [YES; NO]
[3] E.C.M. function setting: [ECM On; ECM Off; Immediately;
After job; Warning]
[5] Lock/delete program
memory
[6] Paper type / Special Size Paper type: [Blank; Normal; Thick; Recycle; Thin; Color;
Set User; Special; Tab paper; Fine; Seal]
Special size: [STD size; STD size (special); Non STD size;
Wide paper]
[7] Panel contrast / [Panel contrast; Backlight contrast; Buzzer volume
Key Sound Adj. regulation]
[8] Key operator data [Name; Key Operator Tel. No.]
setting
[9] Weekly timer [1] Weekly timer ON/OFF setting: [On; Off]
[2] Timer setting: [ON time; OFF time]
[3] Timer action ON/OFF setting: [ON; OFF]
[4] Lunch hour off setting: [Valid; Invalid]
[5] Timer interrupt password set: [4-digit password]
[10] Control paneladjustment
[11] Tray Auto Select Setting ATS/APS switch: [ON; OFF]
Tray priority: [Tray 1, Tray 2, Tray 3, LCC, Bypass]
Key Operator Mode
Function Menu Map (continued)

[12] Energy saver setting Auto low power: [5, 10, 15, 30, 60, 90, 120, 240]
Auto shut off: [---, 30, 60, 90, 120, 240]
[13] Memory switch [1] Panel reset timer
[2] Panel Reset key function
[3] EDH-Original effect
[4] Job memory auto recall (30)
[5] Finisher mode by Full-auto
[6] Initial by Key counter insert
[7] Erasure outside area of original
[8] EDH frame erasure selection
[9] Automatic tray switching
[10] Platen APS
[11] EDH APS
[12] Platen AMS
[13] EDH AMS
[14] Select tray when APS cancel
[15] Platen original size detect
[16] EDH original size detect
[17] Platen orig. size detect (SMALL)
[18] Rotation
[19] Staple mode reset-function
[20] Job offset operating
[21] Continuation print
[22] Key click sound
[23] 1 SHOT indication time
[24] Energy saver screen
[25] Start key latch function
[26] Stop key function
[27] Auto select of Booklet copy
[28] E.C.M. password
[29] Arrow key change (Image Shift)
[30] Exit direction of 1 sheet
[31] An interruption suspended way
[32] E.C.M. password input timing
[33] Key click sound (No paper/JAM)
[34] Reserve copy function
[35] Scan stop by a pull out tray
[36] Change page no. pos. (booklet)
[37] Trimmer (STD/Non STD size) (Function invalid)
[38] Timer which prohibits Print
[39] Bookmark function
[40] Side 2 print (STD repeat + zoom)
[41] Delete of overlay image
[42] Orig. direction/binding mode
[43] Image stored cont. (SRV)
[44] Image recalled cont. (SRV)
[45] Exit direction

Key Operator Mode
Function Menu Map (continued)

[14] Machine management [1] Job memory list
list print [2] User management list
[3] E.C.M. management list
[4] Font pattern list
[15] Call remote center [1] Call for service center
[16] Side 2 lens adjustment [---, -0.1 %, -0.2 %, -0.3 %]
[17] Finisher adjustment [1] Stapling & Folding stopper adj.
[2] Folding stopper adjustment
[4] Punch adjustment
[5] Three-Folding position adj.
[6] 2 positions staple pitch adj.
[18] HDD management [1] Password list/delete
setting [2] JOB auto delete period setting
[3] State of HDD capacity
[20] Non-image area erase [AUTO; Oblique erase; Rectangle erase]
setting ORIGINAL DENS.[Dark+; Dark; Normal; Light; Light+]

Key Operator Mode
System Initial Setting [1]
Set the following initial conditions of the copier.

• Date & Time setting: Current date and time, Summer time, Time difference
• Language select setting: Language used in LCD (English)
• IP address setting: IP address to be accessed from PC
• E-mail transmission setting: E-mail address to be informed of machine trouble or
request for supplies.
Date & Time Setting [1]
Set the current date and time, the summer time, and also the time difference.
❒ Default setting: Summer time off
System Initial Setting Menu Screen Date & Time Setting Screen
Difference in Time Setting Screen
1 Press [Help] to display the Help Screen, then touch Key Operator Mode.
Enter the 4-digit Key Operator password, then touch OK to display the Key Operator
Mode Screen.
2 Touch [1] System initial setting to display the System Initial Setting Menu Screen, then
touch [1] Date & Time setting to display the Date & Time Setting Screen.
3 Adjust the time.
The time indicated by the copier is displayed in the upper line and ordered by date,
month, year, and time (in 24-hour expression). In the lower line, the highlighted section
can be changed by using the keypad on the screen.
Touch SET to move the highlighted section to the number to be changed.

Key Operator Mode
System Initial Setting [1] (continued)
Date & Time Setting [1] (continued)
4 To activate the summer time function, touch Summer time to highlight it. The Present
time will gain an hour.
5 The Difference in time setting is provided in order to give the time difference information
at the same time when E-mail is received.
To set this function, follow the procedure below.
(1)Touch Diff. time setting to display the Difference in Time Setting Screen.
(2)Touch +↔– to display “+” when the local time is earlier than the Universal time, or “–”
when the local time is later.
(3)Use the keypad on the screen to enter the time difference between the Universal time
and the local time in the machine setting area. (e.g. Enter “–0600” for 6 hours later
than the Universal time.)
6 Touch OK to update the Present time by the Setting time and return to the System Initial
Setting Menu Screen.
7 Touch RETURN to restore the Key Operator Mode Screen.
8 Touch RETURN to return to the Basic Screen and perform copying operations.

Key Operator Mode
Language Select Setting [2]
Select the language used in the LCD (English).

❒ Default setting: American English
System Initial Setting Menu Screen Language Selection Screen
Mode Screen.
touch [2] Language select setting to display the Language Selection Screen.
3 Select the desired English mode.
4 Touch OK to complete the setting and return to the System Initial Setting Menu Screen.

Key Operator Mode
IP Address Setting [3]
When using the server function, this setting is required to enable a PC to gain access to
this machine.
NOTE: Ask your network manager to perform this setting. Incorrect setting may cause a trouble with other
network systems.
❒ Setting options: IP address; Subnetmask; Gateway addess, Line speed setting

System Initial Setting Menu Screen IP Address Setting Screen
Mode Screen.
touch [3] IP address setting to display the IP Address Setting Screen.
3 Make the required setting.
Touch to highlight the address key on the left, then enter the address numbers using the
screen keypad. Touch SET to fix the numbers, or touch RESET to clear.
Line Speed Setting Screen
4 When customizing the line speed, touch
Line speed setting to display the Line
Speed Setting Screen. Touch the desired
key, then touch OK to restore the IP
Address Setting Screen.
5 Touch OK to complete the setting and

return to the System Initial Setting Menu Screen.

Key Operator Mode
E-Mail Transmission Setting [4]
When the machine requires troubleshooting or maintenance such as paper or toner

supply, this setting allows several network PCs to be informed of the current machine
status by E-mail.
The following information items are provided.
• Service call • PM call • Finisher tray full
• JAM • Complete job • Dispose of trash basket
• Paper supply • Non complete job
• Toner supply • Staple cartridge supply
NOTE: Ask your network manager to perform this setting. Incorrect setting may cause a trouble with other
network systems.
❒ Setting options: IP address; E-Mail (machine manager); E-Mail (condition inform), E-Mail
transmission item
System Initial Setting Menu Screen E-Mail Transmission Setting Screen
Mode Screen.
touch [4] E-Mail Transmission Setting to display the E-Mail Transmission Setting
Screen.
IP Address Setting Screen
3 Touch [1] IP address setting to display the
IP Address Setting Screen. Enter the IP
address of the mail address in your
network using screen keypad, then touch
OK to restore the E-Mail Transmission
Setting Screen.

Key Operator Mode
E-Mail Transmission Setting [4] (continued)

E-Mail Set (Machine Manager) Screen
4 Touch [2] E-Mail set (machine manager)
to display the E-Mail Set (Machine
Manager) Screen. Enter the E-mail
address of the network manager using
screen keypad, then touch OK to restore
the E-Mail Transmission Setting Screen.
E-Mail Set (Condition Inform) Screen

5 Touch [3] E-Mail set (condition inform) to
display the E-Mail Set (Condition Inform)
Screen. Enter the E-mail address of the
network PC using screen keypad, then
touch OK to restore the E-Mail
Transmission Setting Screen.
Network PC E-mail Address Setting Screen

6 Touch [4] E-Mail transmission item set to
display the Information Setting Screen.
Touch to highlight the desired item key,
then touch OK to restore the E-Mail
Transmission Setting Screen.
7 Touch RETURN to complete the setting and return to the System Initial Setting Menu
Screen.

Key Operator Mode
Copier Initial Setting [2]
Initial settings are the settings that display automatically when the copier is powered on,
when Panel Reset timer is operated, or when [Panel Reset] key is pressed. These settings
can be changed by the Key Operator, as shown in this section.
Initially, i.e., at installation, the Basic Screen displays the following condition to meet
Energy Star requirements:
Initial Setting
Copy Mode: 1-1
Copy Density: AES
Lens Mode: 1:1
Copy Size: APS
Output Mode: offset sort
When Initial settings are changed by the Key Operator, the new initial settings display
when the copier is powered on, when Panel Reset timer is reached, or when [Panel Reset]
key is pressed.
The following initial settings can be changed by the Key Operator:

Copy Mode: [EDH; 1-1; 1-2; 2-2; 2-1]
Copy Density: [AES; manual]
Lens Mode: [AMS; ratio 0.250~4.000]
Copy Size: [APS; trays 1, 2, 3, or LCC]
Output Mode: [Non-sort; Sort; Group; Staple-sort; Stapling & Folding; Folding;
Punch; Three-folding; cover sheet]
Special Original: [Original Direction; Text/Photo Enhance; Special Original; Original
Form]
Rotation: OFF
Setting procedures are described on the following pages.

NOTE: The most commonly-used settings are established at installation. Before changing any of the copier
settings, be sure that you understand the overall and long-range effect of the change.

Key Operator Mode
Copier Initial Setting [2] (continued)

Key Operator Mode Screen Copier Initial Setting Screen
Mode Screen.
2 Touch [2] Copier initial setting to display the Copier Initial Setting Screen.
3 Make a selection for each mode as initial settings.
Touch EDH to select or deselect it.
NOTE: The machine will restore the initial settings specified as above unless the Memory switch No. 4 “ Program
memory (30) auto recall” is turned ON with the Job memory No. 30 registered.
4 Touch OK to complete the setting and return to the Key Operator Mode Screen.

Key Operator Mode
User Setting Mode [3]
Set two user-set density levels and three USERSETs of magnification.
Output copying samples from 16 density levels from Lighter to Normal or Normal to
Darker, then select the desired exposure and program it as USER 1.
The programmed copy density can be recalled by selecting USER 1 on the Basic Screen.
User Setting Mode Menu Screen User Density Level 1 Setting Screen
Mode Screen.
2 Touch [3] User setting mode to display the User Setting Mode Menu Screen, then touch
[1] User density level 1 setting to display the User Density Level 1 Setting Screen.
3 Place the original on the platen glass or in the EDH.
4 Touch Darker or Lighter to select the density level to be programmed.
5 Touch No.1 1~4, No.2 5~8, No.3 9~12, No.4 13~16, or Set density ##, then press [Start].
A density level sample sheet will be output.
6 Select the desired exposure from the sample sheet(s), then enter the density level
number by using the touch screen keypad.
7 Touch OK to complete the setting and return to the User Setting Mode Menu Screen.

Key Operator Mode
User Setting Mode [3] (continued)
Output copying samples from 16 density levels from Lighter to Normal or Normal to
Darker, then select the desired exposure and program it as USER 2.
The programmed copy density can be recalled by selecting USER 2 on the Basic Screen.
User Setting Mode Menu Screen User Density Level 2 Setting Screen
Mode Screen.
[2] User density level 2 setting to display the User Density Level 2 Setting Screen.
3 Place the original on the platen glass or in the EDH.
4 Touch Darker or Lighter to select the density level to be programmed.
5 Touch No.1 1~4, No.2 5~8, No.3 9~12, No.4 13~16, or Set density ##, then press [Start].
A density level sample sheet will be output.
6 Select the desired exposure from the sample sheet(s), then enter the density level
number by using the touch screen keypad.

Key Operator Mode
User Setting Mode [3] (continued)
User Lens Mode Ratio Setting [3]
The preset and userset ratios available on the Basic Screen are used to reduce and
enlarge the original image to accommodate copy paper size.
Normally, users are allowed to change the three Customs in the bottom line on the User
Lens Mode Ratio Setting Screen. The preset keys in the top and middle lines can be
programmed in 2-5 DIP SW mode for special purposes, but ordinarily, it is recommended
that they remain unchanged.
❒ Setting options: Preset ratio or Custom zoom
❒ Default setting: Custom 1: 4.000
Custom 2: 2.000
Custom 3: 0.500
User Setting Mode Menu Screen User Lens Mode Ratio Setting Screen
Mode Screen.
[3] User lens mode ratio setting to display the User Lens Mode Ratio Setting Screen.
3 Touch the Custom you want to change, then enter a ratio from 0.250~4.000, using the
keypad.
If a ratio under 0.250 is entered, 0.250 will be displayed.
If a ratio over 4.000 is entered, 4.000 will be displayed.

DL650us132v1.fm 18 ページ２００１年１１月１４日　水曜日　午後３時３６分
Key Operator Mode
ECM (Electronic Copy Monitor) Function Setting [4]
This function can only be accessed by the Key Operator after an 8-digit ECM master key
code is entered. The Electronic Copy Monitor allows you to monitor all copying activity by
controlling ECM password accounts.
This feature can track copier usage for individual users and/or accounts as well as limit
copier access to only authorized users. Copy quantity limits for specific accounts can also
be set. Use the ECM Key Operator Form provided at the end of this section to record ECM
password information.
The ECM stores up to 1,000 ECM passwords, each of which represents a separate
account that can be used for billing and record keeping. The number of users assigned to
each account may depend upon the billing system in operation and the number of
individuals and departments using the copier. When the ECM is activated, copying can be
performed only after a valid ECM password is entered.
Copy quantity and copy limits for each account can be visually confirmed on the screen.
If ECM needs to be activated on your machine, contact your service representative.
The following ECM settings can be made:
[1] E.C.M. data edit:

Change, add, or delete ECM data, and reset the copy count of the individual account.
[2] E.C.M. all count reset:

Clear the copy count for all accounts.
[3] E.C.M. function setting:

Turn the ECM function on or off, and set conditions to stop immediately, stop after job is
completed or display a warning message when copy limit is reached.

Key Operator Mode
ECM (Electronic Copy Monitor) Function Setting [4] (continued)
How to Access the ECM Setting Mode

Key Operator Mode Screen ECM Master Key Code Screen
ECM Setting Menu Screen
Mode Screen. (See note 1.)
If the Key Operator password is not valid, check with your service representative.
2 Touch [4] E.C.M. function setting. The ECM Master Key Code Screen displays if a code
is required.
3 Use the keypad on the touch screen to enter your 8-digit ECM master key code, then
touch OK to display the ECM Setting Menu Screen. (See note 2.)
4 Select the desired ECM function, and make settings as required.
To exit the ECM mode, touch RETURN on ECM Setting Menu Screen.
5 Touch RETURN on the Key Operator Mode Screen to return to the Basic Screen.
NOTES: 1 If an invalid password is entered, enter the valid 4-digit password.

2 If an invalid ECM master key code is entered, continue by entering the valid 8-digit code. The ECM
master key code can be set to less than 8 digits by the Memory switch setting of the Key Operator
function.

Key Operator Mode
E.C.M. Data Edit [1]
Use this setting to display the list of copy count and copy limit for each account, to change,
add, or delete the ECM data, and to reset the copy count of the individual account.
❒ ECM No.: Designated by Key Operator

❒ ECM Password: Unique 8-digit numeric code programmed by Key Operator for user
❒ User Name: Max. 8 characters
❒ Copy Limit: 0 to 999,999 copies
ECM Setting Menu Screen ECM Data Edit Screen
ECM Data Change Screen ECM Data Add Screen
Password Duplication Screen Name Duplication Screen

Key Operator Mode
E.C.M. Data Edit [1] (continued)
2 Touch [4] E.C.M. function setting. The ECM Master Key Code Screen displays, if a code
is required.
3 Enter your 8-digit ECM master key code, then touch OK to display the ECM Setting
Menu Screen. (See note 2.)
2 If an invalid ECM master key code is entered, continue by entering the valid 8-digit code.
4 Touch [1] E.C.M. data edit. The ECM Data Edit Screen will be displayed.
To change, add, or delete the ECM data, and to reset the copy count of an individual
account, follow the procedure for each as described below.
To Change ECM Data:

(1) Touch ▲ or ▼ key on the right side of the list to highlight the ECM data to be changed,
then touch Change. The ECM Data Change Screen will be displayed.
(2) Touch the desired item key to highlight it, then enter new data by using the touch
screen keypad.
Password: 8 digits max. (See note 1.)
Name: 8 characters max. (See note 2.)
Limit: 999,999 copies max.
NOTES: 1 We recommend that you make a list of all ECM passwords and account numbers.
2 If an invalid user name is entered, continue by entering the valid name.
(3) Touch OK to complete the setting and to verify whether the same password or name
has been already used for another account number.
When a password is duplicated:
The Password Duplication Screen will be displayed. Touch YES to re-enter new
password, or NO to create duplicate password.
NOTE: If duplicate password is created, the number of copies will be counted only for the ECM password with
the smallest number. We recommend you do not use duplicate ECM passwords.
When a name is duplicated:

The Name Duplication Screen will be displayed. Touch OK to re-enter new name.

Key Operator Mode
To Add ECM Data:

(1) Touch Add on the ECM Data Edit Screen. The ECM Data Add Screen will be
displayed.
(2) Touch the desired item key to highlight it, then enter the data by using the touch screen
keypad.
Password: 8 digits max. (See note 1.)
Name: 8 characters max. (See note 2.)
Limit: 999,999 copies max.
NOTES: 1 We recommend that you make a list of all ECM passwords and account numbers.
2 If an invalid user name is entered, continue by entering the valid name.
(3) Touch OK to complete the setting and to verify whether the same password or name
has been already used for another account number.
When a password is duplicated:
The Password Duplication Screen will be displayed. Touch YES to re-enter new
password, or NO to create duplicate password.
NOTE: If duplicate password is created, the number of copies will be counted only for the ECM password with
the smallest number. We recommend you do not use duplicate ECM passwords.
When a name is duplicated:

The Name Duplication Screen will be displayed. Touch OK to re-enter new name.
To Delete ECM Data:

(1) Touch ▲ or ▼ key on the right side of the list to highlight the ECM data to be deleted,
then touch Delete. The Delete Confirmation Screen will be displayed.
(2) Touch YES to delete, or NO to cancel.
To Clear ECM Count:

(1) Touch ▲ or ▼ key on the right side of the list to highlight the desired ECM data, then
touch COUNT RESET. The Reset Confirmation Screen will be displayed.
(2) Touch YES to clear the copy count of the selected ECM data, or NO to cancel.
Delete Confirmation Screen Reset Confirmation Screen

Key Operator Mode
5 Touch RETURN on the ECM Data Edit Screen to return to the ECM Setting Menu
Screen. If other ECM setting changes are required, touch the desired key, from [1]~[3].

Key Operator Mode
E.C.M. All Count Reset [2]
Reset the count for all ECM accounts.
ECM Setting Menu Screen ECM All Count Reset Screen
is required.
4 Touch [2] E.C.M. all count reset. The ECM All Count Reset Screen will be displayed.
5 Touch YES to reset all counters to zero and to return to the ECM Setting Menu Screen or
touch NO to cancel.
Touching RETURN will also cancel this function and return to the ECM Setting Menu
Screen.
6 If other ECM setting changes are required, touch the desired key, from [1]~[3].


Key Operator Mode
E.C.M. Function Setting [3]
Use this function to turn ECM On or Off and to select whether the copier will stop at the
time the count limit is reached, or after the current copy job is completed.
ECM Setting Menu Screen ECM Function Setting Screen
is required.
4 Touch [3] E.C.M. function setting. The ECM Function Setting Screen will be displayed.
5 Touch ECM On to activate ECM or touch ECM Off to de-activate ECM.
The selected key will be highlighted.
6 Touch Immediately to stop the machine at once when the copy limit is reached.
In this case, copy conditions selected for the current job will be cleared. To continue the
job using the same user password, change the copy limit of the password or clear the
copy count.
Touch After job to stop the machine after the current job is completed, when copy limit is
reached.
Touch Warning only to display a warning message when copy limit is reached.
7 Touch OK to complete the setting and return to the ECM Setting Menu Screen. If other
ECM setting changes are required, touch the desired key, from [1]~[3].


Key Operator Mode
Lock/Delete Program Memory [5]
Use this function to lock/unlock or delete a Job that has been programmed.
A locked Job is indicated by a lock icon ( ) on the Lock/Delete Program Memory Screen.
The settings of a locked Job cannot be changed.
❒ Setting options: Lock Program memory; Unlock Program memory; Delete Program memory
❒ Lock/delete is available for all 30 stored jobs
❒ A blank key indicates that no Job is programmed
❒ ✽✽✽✽✽✽✽✽✽✽✽✽✽✽✽✽ indicates that a Job is programmed but unnamed
Key Operator Mode Screen Lock/Delete Program Memory Screen
Mode Screen. (See note.)
2 Touch [5] Lock/delete program memory to display the Lock/Delete Program Memory
Screen.
To lock/unlock a Program memory:
(1) Touch the key on the left side of the desired Job number. Use arrow keys to scroll to
the desired Job number, if required.
(2) The lock icon will appear on the touched key to show that the selected job is locked.
The previously locked Job will be unlocked when selected, and the lock icon on the
touched key will disappear.
To delete a Program memory:
(1) Touch the Job number you want to delete. Use arrow keys to scroll to the desired Job
number, if required.
(2) Touch DELETE. Selected programs and the name will be deleted from the Program
memory.

Key Operator Mode
Paper Type / Special Size Set [6]
Use this function to indicate a specific paper type or to specify a special paper size for
each tray key on the Basic Screen. This is especially useful when special paper is used on
a regular basis and is always placed in a specific paper tray.
Key Operator Mode Screen Paper Type Setting Screen
Special Size Setting Screen (STD size) Special Size Setting Screen (STD size (special))
Special Size Setting Screen (Non STD size) Special Size Setting Screen (Wide size paper)
Special Size Setting Screen (Input size))

Key Operator Mode
Paper Type / Special Size Set [6] (continued)
2 Touch [6] Paper type / Special size set to display the Paper Type Setting Screen.
To specify paper type:
(1) Touch the desired paper tray key to highlight it.
(2) Touch the arrow keys to select paper type.
To specify special size:

(1) Touch Special size setting on the Paper Type Setting Screen to display the Special
Size Setting Screen.
(2) Touch the desired paper tray to highlight it.
(3) Touch a paper size key to specify a paper size for the selected tray.
• Select STD size to allow the machine to automatically detect the size of paper
loaded in the tray and indicate it on the tray key.
• Select STD size (special) to display the popup menu to show available paper sizes
to be specified. Use arrow keys on the popup menu to select the desired size.
• Select Non STD size to display the popup menu to enter the paper size by using
arrow keys or touch screen keypad.
• Select Wide paper to display the popup menu to show available wide paper sizes to
be specified. Use arrow keys on the popup menu to select the desired wide size.
Touch Lead edge or Rear edge to select the image starting position.
Then, touch Input size to display the popup menu to enter the paper size by using
arrow keys or touch screen keypad.
3 Touch OK on the Paper Type Setting Screen or on the Special Size Setting Screen to
complete the setting and return to the Key Operator Mode Screen.

Key Operator Mode
Panel Contrast / Key Sound Adjustment [7]
Use this feature to adjust the level of brightness of the touch screen portion of the control
panel, and also the volume of the touch key.
Key Operator Mode Screen Panel Contrast/Key Sound Adjustment Screen
2 Touch [7] Panel contrast/Key sound adj. to display the Panel Contrast/Key Sound
Adjustment Screen.
3 Adjust the Panel contrast, Backlight contrast, or Buzzer volume, as desired.
Touch Dimmer to make the panel or backlight contrast dimmer than currently displayed,
or touch Brighter to make the panel or backlight contrast brighter than currently
displayed.
Touch Small or Big to regulate the buzzer volume of the touch keys.

2 The control panel contrast feature can be adjusted from the Help screen, provided the feature setting
is activated by your service representative. When the Control panel contrast key is pressed, the Con-
trast Adjustment Screen will be displayed. Contact your service representative if the feature is
required.

Key Operator Mode
Key Operator Data Setting [8]
Use this screen to enter the name and extension number of the Key Operator indicated on
the Help Screen that develops from the Basic Screen.
❒ Setting options: 5-digit Key Operator telephone extension; Max. 8-character Key Operator name
Key Operator Mode Screen Key Operator Data Setting Screen
2 Touch [8] Key operator data setting to display the Key Operator Data Setting Screen.
3 Touch Name to highlight it, then enter the key operator name up to 8 characters from the
touch screen keypad.
4 Touch Key Operator Tel. No. to highlight it, then enter a 5-digit extension number from
the touch screen keypad. If the extension number is less than 5 digits, use a hyphen [-]
to make it five. The hyphen added in the beginning will be indicated as a space on the
Help Screen.

DL650us133v1.fm 31 ページ２００１年１１月１４日　水曜日　午後３時４５分
Key Operator Mode
Weekly Timer [9]
This function can be accessed only by the Key Operator after a unique 4-digit Weekly
Timer master key code is entered.
The Weekly Timer is a copier management function that shuts down power to the machine
on a daily or hourly basis, and can be programmed specifically for lunch breaks, weekends
and holidays, or any time the copier is not required.
In addition, Timer Interrupt can be enabled (with or without a password requirement) to
allow temporary use of the machine during periods when power is shut down by the Timer
function.
Conditions required to use the Weekly Timer

• The power plug is inserted into the socket.
• The power switch is turned on.
• The current date and time are correctly set.
If the Weekly Timer needs to be activated on your machine, contact your service
representative.
The following Weekly Timer settings can be made.
[1] Weekly timer ON/OFF setting

Enable and disable the Timer function.
[2] Timer Setting
Specify the times that the copier will turn ON and OFF for each day of the week or the
entire week.
[3] Timer action ON/OFF Setting
Specify the working days of the machine by the Timer, for all Mondays through Sundays,
and/or individually for each day of the specified month.
[4] Lunch hour off setting
Specify the lunch time interval during which the copier will turn off and on.
[5] Timer interrupt password set
Require Password entry for the Timer off function and establish the amount of usage time.
NOTES: 1 The time is set in terms of the 24 hour clock, where hour [1] is the first hour after midnight; and hour
[24] is midnight. For example, 6 a.m. is 06:00 hours; 6 p.m. is 18:00 hours.
2 The [Panel Reset] key is used to change numbers determined by the SET touch key.

Key Operator Mode
Weekly Timer [9] (continued)
How to Access the Weekly Timer Setting Mode

Key Operator Mode Screen Weekly Timer Master Key Code Screen
Weekly Timer Setting Menu Screen
2 Touch [9] Weekly timer.
The Weekly Timer Master Key Code Screen displays, if a code is required.
3 Use the keypad on the touch screen to enter your 4-digit Weekly Timer master key code,
then touch OK to display the Weekly Timer Setting Menu Screen. (See note 2.)
4 Select the desired Weekly Timer function, and make settings, as required.
5 To exit the Weekly timer mode, touch RETURN on the Weekly Timer Setting Menu
Screen.
6 To exit the Key Operator mode, touch RETURN on the Key Operator Mode Screen. The
Basic Screen will be displayed.

2 If an invalid Weekly Timer master key code is entered, continue by entering the valid 4-digit code.

Key Operator Mode
Weekly Timer On/Off Setting [1]

Weekly Timer Setting Menu Screen Weekly Timer On/Off Setting Screen
2 Touch [9] Weekly timer. Enter your 4-digit Weekly Timer master key code, then touch OK
to display the Weekly Timer Setting Menu Screen. (See note 2.)
3 Touch [1] Weekly timer ON/OFF setting to display the Weekly Timer On/Off Setting
Screen.
4 Touch Weekly timer On to activate Weekly Timer, or touch Weekly timer Off to de-
activate Weekly Timer. The default setting is Weekly Timer Off.
5 Touch OK to complete the setting and return to the Weekly Timer Setting Menu Screen.
If other Weekly Timer setting changes are required, select the desired menu item, from
[1]~[5].


Key Operator Mode
Timer Setting [2]
Use this function to set the On/Off times in hours and minutes for each day of the week or
set the collective time for the entire week, i.e., the same On/Off time for each day.
Weekly Timer Setting Menu Screen Weekly Timer On/Off Time Setting Screen
Weekly Timer On/Off Time Collective Setting Screen
3 Touch [2] Timer setting to display the Weekly Timer On/Off Time Setting Screen.
4 When the screen is displayed, the ON-time of Monday is always highlighted.
Enter a 2-digit ON-hour (ex. 8 a.m. is 08) and a 2-digit ON-minute (ex. 7 min. is 07)
using the touch screen keypad, and then touch SET.
Touching SET repeatedly will shift the input section from Monday ON, Monday OFF,
Tuesday ON, Tuesday OFF.
NOTES: • If ON-time and OFF-time are the same, power will not go on.
• If the setting is 00:00~00:00, you will not be able to set the copiers off/on condition for specific days.
When setting Sunday OFF-time, Monday ON-time is highlighted again. Proceed to step
7.
5 To set the ON/OFF time collectively for more than one day of the week, touch Block set
to display the Weekly Timer On/Off Time Collective Setting Screen.
Key Operator Mode
Timer Setting [2] (continued)
6 When you open this screen, the ON and OFF times are always set at 00:00~00:00.
Touch to highlight the day(s) of the week to be set. More than one can be selected at a
time.
Enter the ON-time and OFF-time using the touch screen keypad, and then touch SET
after each entry.
7 Touch OK on the Weekly Timer On/Off Time Setting Screen or on the Weekly Timer On/
Off Time Collective Setting Screen to complete the setting, and return to the Weekly
Timer Setting Menu Screen. If other Weekly Timer setting changes are required, select
the desired menu item, from [1]~[5].

Key Operator Mode
Timer Action On/Off Setting [3]
Use this function to set the On/Off condition of the copier for a given month. Set the On-Off
condition for specific days or collectively, for all Mondays through Sundays of the given
month. The default setting is collective: On for Mondays through Saturdays, and Off for
Sundays.
Weekly Timer Setting Menu Screen Timer Action On/Off Setting Screen
Timer Action Change Confirmation Screen
3 Touch [3] Timer action ON/OFF setting to display the Timer Action On/Off Setting
Screen.
The days of the current month are displayed on the left half of the screen, with timer-
active days highlighted.
4 To activate or deactivate the Timer for any individual day, touch the key for that day to
change its indication.
To change the month, use arrows to scroll to the desired month.
5 To collectively set the on/off data for the entire month by the day of the week, touch the
ON or OFF key for the desired day on the right half of the screen. If you touch an
already-highlighted key, no change will occur.
Key Operator Mode
Timer Action On/Off Setting [3] (continued)
6 If any change is made in the collective setting area, the Timer Action Change
Confirmation Screen will be displayed.
Touch YES to change the timer action, or touch NO to cancel.
The Timer Action On/Off Setting Screen will be restored.
7 Touch OK on the Timer Action On/Off Setting Screen to complete the setting and return
to the Weekly Timer Setting Menu Screen. If other Weekly timer setting changes are
required, select the desired menu item, from [1]~[5].

Key Operator Mode
Lunch Hour Off Setting [4]
The Weekly Timer function turns the copier ON and OFF once a day. Use the Lunch hour
off function to shut down power during the lunch break and then turn it on again according
to the Weekly Timer function setting. Only one off-time interval can be programmed.
Weekly Timer Setting Menu Screen Lunch Hour Off Setting Screen
3 Touch [4] Lunch hour off setting to display the Lunch Hour Off Setting Screen.
4 Touch Function Valid to activate the Lunch hour off function. Set OFF-time and Restart-
time using the touch screen keypad, and then touch SET after each entry.
Touch Function Invalid to de-activate the Lunch hour off function. The time setting area
will appear grayed out and cannot be selected.
The Function Invalid setting is the factory default setting.
5 Touch OK to complete the setting and return to the Weekly Timer Setting Menu Screen.
[1]~[5].


Key Operator Mode
Timer Interrupt Password Setting [5]
Use this password setting mode to establish a 4-digit password requirement for using
Timer Interrupt function. The default password of 0000 allows the timer function to be
interrupted without the requirement for password entry.
Weekly Timer Setting Menu Screen Timer Interrupt Password Setting Screen
3 Touch [5] Timer interrupt password set to display the Timer Interrupt Password Setting
Screen.
4 Use the touch screen keypad to enter a 4-digit password, and then touch OK to
complete the setting and return to the Weekly Timer Setting Menu Screen.
NOTE: When the password setting is 0000, Timer Interrupt can be used simply by turning the copier OFF, then
ON. In this case, you will be asked to enter the duration of use (a period of time to turn the copier power
on).
[1]~[5].

Key Operator Mode
Control Panel Adjustment [10]
Use this feature to check the LCD touch screen and realign the position of the touch
sensor that may have shifted.
Key Operator Mode Screen Control Panel Adjustment Screen
2 Touch [10] Control panel adjustment to display the Control Panel Adjustment Screen.
3 Touch the “+” symbol at the upper right corner, then lower left corner on the screen. The
present coordinates will be displayed in the message area of the screen.
4 Check that the X coordinate and Y coordinate displayed in the first line of the message
area fall within the standard value displayed in the second line.
5 Touch the CHECK BUTTONs at the upper left and lower right corners on the screen to
check if the buzzer tone functions normally.
6 If the coordinates fall out of the range of the standard value in step 4, or the buzzer tone
does not sound in step 5, repeat the adjustment procedure from 3 to 5 or contact your
service representative.
7 Press [1] of the control panel keypad to restore the Key Operator Mode Screen.

Key Operator Mode
Tray Auto Select Setting [11]
Select whether the tray size setting will be detected or not detected when ATS/APS
functions. If you select it to be detected, you may also select the priority of the detection for
each tray.
Tray Auto Select Setting Screen
To display menus [11] to [20] of the Key Operator Mode Screen, touch the Lower
arrow key.
2 Touch [11] Tray auto select setting to display the Tray Auto Select Setting Screen.
3 On the left half of the screen, touch to highlight each tray key, then select OFF or ON to
specify whether the selected tray is to be automatically detected or not when ATS/APS
functions.
4 Tray keys specified as ATS/APS ON will appear on the right half of the screen.
Touch to highlight the desired tray key, then change its priority by using Up ▲ and Down
▼ arrow keys.
5 Touch OK to complete the setting and restore the Key Operator Mode Screen.

Key Operator Mode
Energy Saver Setting [12]
Select the interval of time that must elapse before Auto Low Power and Auto Shut Off
become activated. Auto Shut Off conserves more energy than Auto Low Power. The period
of time selected for Auto Low Power cannot exceed the Auto Shut Off setting.
Energy Saver Setting Screen
Mode Screen.
arrow key.
2 Touch [12] Energy saver setting to display the Energy Saver Setting Screen.
3 The periods of time currently selected for each energy saver function are located on the
Timer Setting Screen below the Auto Low Power and Auto Shut Off indicators.
Touch the arrow keys (▲) and (▼) in each area to select a specific waiting period before
activating the Auto Low Power or Auto Shut Off.
NOTES: 1 The period of time selected for Auto Low Power cannot exceed the Auto Shut Off setting.
2 If the same period of time as Auto Shut Off is selected for Auto Low Power, the Auto Shut Off will func-
tion instead of Auto Low Power.
4 Touch OK to complete the setting and restore the Key Operator Mode screen.

Key Operator Mode
Memory Switch Setting [13]
This function allows you to change the Memory Settings listed below. See pp. 13-45~13-
49 for details on Memory Settings.
SW No. Item Setting (default is underlined)

No. 01: Panel reset timer OFF/ 30 sec./ 60 sec./ 90 sec./ 120 sec./150 sec./
180 sec./ 210 sec./ 240 sec./ 270 sec./ 300 sec.
No. 02: Panel Reset key function Full-Auto/ Initial Setting
No. 03: EDH-Original effect EDH+Panel Reset key selected/ EDH selected
No. 04: Program memory auto recall (30) OFF/ ON
No. 05: Finisher mode by Full-auto Face down (Sub tray)/ Non-sort/ Sort/ Staple sort/
Stapling & Folding/ Folding/ Face up (Sub tray)
No. 06: Initial by Key counter insert OFF/ ON
No. 07: Erasure outside area of orig. Erased for except Platen (1:1)/ Area outside of
orig. erased/ Erased for APS/AMS only
No. 08: EDH frame erasure selection None/ 1mm frame/ 2mm frame/ 3mm frame/ 4mm
frame/ 5mm frame
No. 09: Automatic tray switching OFF/ ON
No. 10: Platen APS OFF/ ON
No. 11: EDH APS OFF/ ON
No. 12: Platen AMS OFF/ ON
No. 13: EDH AMS OFF/ ON
No. 14: Select tray when APS cancel APS preferential tray/ Tray 1/ Tray 2/ Tray 3/ LCC/
Bypass tray
No. 15: Platen original size detect Only A series/ Full size/ AB series/ Inch series
No. 16: EDH original size detect Only A series/ Full size/ AB series/ Inch series
No. 17: Platen orig. size detect (SMALL) A5R/ B6R/ 5.5"x8.5"R/ B5/ A4/ 8.5x11
No. 18: Rotation ON-APS/AMS only/ ON-APS/AMS/Reduce only/
ON-Always
No. 19: Staple mode reset-function OFF/ ON
No. 20: Job offset operating OFF/ ON
No. 21: Continuation print OFF/ ON
No. 22: Key click sound OFF/ ON
No. 23: 1 SHOT indication time 3 seconds/ 5 seconds
No. 24: Energy saver screen Shut off mode/ Low power mode
No. 25: Start key latch function OFF/ ON
No. 26: Stop key function JOB momentary stop/ JOB cancel
No. 27: Auto select of Booklet copy Automatic selection/ Non Automatic selection
No. 28: E.C.M. password Under 8 digits/ 8 digits

Key Operator Mode
Memory Switch Setting [13] (continued)
No. 29: Arrow key change (Image Shift) Decimal point off (1 STEP 1mm)/ Decimal point
on (1 STEP 0.1mm)
No. 30: Exit direction of 1 sheet Face up/ Face down
No. 31: An interruption suspended way Division of a number of copies/ During of a
number of copies
No. 32: E.C.M. password input timing Panel reset timer/ Complete job
No. 33: Key click sound (No paper/JAM) OFF/ 3 seconds/ 5 seconds/ 10 seconds
No. 34: Reserve copy function Reserve copy by folder select/ Reserve copy by
original set
No. 35: Scan stop by a pull out tray ON/ OFF
No. 36: Change page no. pos. (booklet) OFF/ ON (Outside page numbering)
No. 37: Trimmer (STD/Non STD size) STD size/ Non STD size
(Function invalid)
No. 38: Timer which prohibits Print OFF/ 15 seconds/ 30 seconds/ 60 seconds/ 90
seconds
No. 39: Bookmark function ON (It is cancel every JOB)/ ON (It is not cancel
every JOB)/ OFF
No. 40: Side 2 print (STD repeat + zoom) Rotation (180 angle) by force/ Normal
No. 41: Delete of overlay image Permission (Delete/Overwrite)/ Prohibition
(Delete/Overwrite)
No. 42: Orig. direction/binding mode It is cancel every JOB/ It is not cancel every JOB
No. 43: Image stored cont. (SRV) OFF/ ON
No. 44: Image recalled cont. (SRV) OFF/ ON
No. 45: Exit direction Face down/ Face up
Memory Switch Setting Screen

Key Operator Mode
arrow key.
2 Touch [13] Memory switch setting to display the Memory Switch Setting Screen.
3 Use the procedure below to select the desired item and change the setting.
(1) To select the desired item, touch the arrow keys (▲) and (▼) at the right of the
Memory Switch Setting Screen.
(2) To scroll, touch the arrow keys at the lower left of the screen.
(3) Touch Change Setting Contents to change the setting of the highlighted item.
(4) Repeat above steps (1) to (3) to make several changes in succession.
The following functions can be provided by the Memory Switch settings.
[1] Panel reset timer

Set the reset interval starting from the completion of a copying job until the machine
returns to the initial condition.
[2] Panel Reset key function

Set the condition of the following modes when [Panel Reset] is pressed: Copy mode, Copy
density, Magnification, Tray selection.
[3] EDH-Original effect

Set the machine condition when original is set on EDH in non-EDH mode with EDH unit
closed.
[4] Program memory auto recall (30)

Program memory number 30 is automatically recalled when power is turned on or when
Panel Reset is restored.
This job recall function works only when Job number 30 is registered.
[5] Finisher mode by Full-auto

Set the Finisher mode to be recalled when [Panel Reset] is pressed.

Key Operator Mode
[6] Initial by Key counter insert

Set the machine to return to the initial state when Key counter is inserted.
[7] Erasure outside area of original

Set the machine to delete the outside area of originals.
[8] EDH frame erasure selection

Set Frame erasure to function anytime in EDH mode.
[9] Automatic tray switching

When paper is depleted during a copying job, the copier continues copying by switching to
another tray that contains the same size paper.
[10] Platen APS

The copier automatically selects the same size copy paper as the original placed on the
platen glass. (In reduction or enlargement mode, an appropriate paper size is selected
according to the ratio selected.)
[11] EDH APS

The copier automatically selects the same size copy paper as the original placed on the
EDH. (In reduction/enlargement mode, an appropriate paper size is selected according to
the ratio.)
[12] Platen AMS

The copier detects the size of the platen original and selects the appropriate magnification
ratio to correspond to the selected paper size.
[13] EDH AMS

After detecting the original size placed on the EDH the copier automatically selects an
appropriate ratio for the copy when copy size is selected manually.
[14] Select tray when APS cancel

Select the tray to be automatically selected when APS is released.
[15] Platen original size detect

Select the series of the original paper size detected from the platen glass.
[16] EDH original size detect

Select the series of the original paper size detected from the EDH.

Key Operator Mode
[17] Platen orig. size detect (SMALL)

Select the minimum original size detected from the platen glass.
[18] Rotation
Select to activate the Rotation function, activate Rotation only when APS/AMS functions,
or activate Rotation only when APS/AMS/Reduce functions.
[19] Staple mode reset-function

Staple mode is automatically canceled after a job is completed with Staple sort mode ON.
(Sort mode is selected.)
[20] Job offset operating

Set the copier to offset the copies of different jobs when outputting multiple reserve jobs in
succession.
[21] Continuation print

Set the copier to output multiple reserve jobs in succession.
[22] Key click sound

Activate or deactivate the sound each time a key is pressed on the touch panel .
[23] 1 SHOT indication time

Select the SHOT indication time function.
[24] Energy saver screen

Select the screen to display when pressing the [Energy Saver] key .
[25] Start key latch function

Activate or deactivate the latch function.
[26] Stop key function

Select to display or not to display the confirmation message when [Stop] key is pressed.
[27] Auto select of Booklet copy

Set the copier with 9922 Finisher mounted to automatically select the Booklet mode when
Stapling & Folding or Folding output mode is selected.
[28] E.C.M. password

Select the acceptable number of digits for the ECM master key code.

Key Operator Mode
[29] Arrow key change (Image Shift)

Select the 1 step unit of the touch key to specify the shift amount in Image shift.
[30] Exit direction of 1 sheet

Select to exit face up or face down when making only 1 sheet of copy.
[31] An interruption suspend way

Select the timing to stop the job in progress when [Interrupt] key is pressed.
[32] E.C.M. password input timing

Set the input timing for the ECM password.
[33] Key click sound (No paper/JAM)

Select the duration of the buzzer that alerts when the machine is out of paper or when
paper has misfed.
[34] Reserve copy function

Set the timing for the reserve job setting.
[35] Scan stop by a pull out tray

Select to stop or continue the scanning job when a tray is pulled out.
[36] Change page no. pos. (booklet)

Set the machine to position the page numbers automatically on the outside edges of the
copy when using Booklet with Page Numbering in Stamp.
[37] Trimmer (STD/ Non STD size) (Function invalid)

Set the machine to allow trimming the folded or stapled & folded sheets in non-standard
size (or wide size).
[38] Timer which prohibits Print

Set the timer to allow the printing job after operating the copying job.
[39] Bookmark function

Select to set the Bookmark function only for the current job, set for all the following jobs, or
deactivate the function.
[40] Side 2 print (STD repeat + zoom)

Select to activate or deactivate the function to rotate the back pages by 180° automatically
in duplex copying with magnification changed and the STD repeat selected.
Key Operator Mode
[41] Delete of overlay image

When selecting (or storing) overlaying image data in HDD using Overlay Memory, select to
permit or prohibit deleting the selected data (or overwriting the data of the same name
previously stored in HDD).
[42] Orig. direction/binding mode

Select to reset or save the original direction and bind position settings made on the Special
Original Screen and Output Mode Screen after completion of each copying job.
[43] Image stored cont. (SRV)

When storing the image data in HDD in server mode, select to release or continue the
server mode after completion of each image data storing job.
[44] Image recalled cont. (SRV)

When recalling the image data stored in HDD in server mode, select to recall only one job
or to recall multiple jobs.
[45] Exit direction

Select to exit face up or face down when making single-sided copies in non-sort or sort
mode using finisher primary (main) tray.

Key Operator Mode
Machine Management List Print [14]
Use this function to print out the list selected from the following items.
• Program memory list: Programmed contents of Program memory
• User management list: Home position settings selected by user
• E.C.M. management list: Machine information managed by ECM
• Font pattern list: Font patterns used in the machine
Key Operator Mode Screen 2 Management List Print Menu Screen
arrow key.
2 Touch [14] Machine management list print to display the Management List Print Menu
Screen.
3 Touch the desired item on the screen. The Basic Screen will resume automatically.
4 Press [Start] to start printing the selected list.
To suspend printing, press [Stop]. Press [Utility] and [C] in order to return to the
Management List Print Menu Screen.

Key Operator Mode
Call Remote Center [15]
When activated, the Remote Diagnostics option is automatically monitored by your service
representative. Your service representative will contact you to determine the appropriate
means for resolving the problem.
❒ Setting options: Call for service center
Key Operator Mode Screen 2 Call Remote Service Center Screen
Start Call Screen
arrow key.
2 Touch [15] Call remote center to display the Call Remote Service Center Screen.
3 Touch [1] Call for service center.
The Start Call Screen will be displayed.
4 Touch Start to call.

Key Operator Mode
Side 2 Lens Adjustment [16]
Use this function to set the adjustment data of the magnification ratio for each tray as Side
2.
Key Operator Mode Screen 2 Side 2 Lens Adjustment Screen
arrow key.
2 Touch [16] Side 2 lens adjustment to display the Side 2 Lens Adjustment Screen.
3 Touch to highlight the desired tray key, then touch arrow keys to select an adjustment
data.
The selected data will be displayed on the highlighted tray key.

Key Operator Mode
Finisher Adjustment [17]
Use this mode to make fine adjustments to each function of the finisher.
Key Operator Mode Screen 2 Finisher Adjustment Menu Screen
Stapling&Folding Stopper Position Adjustment Screen Folding Stopper Position Adjustment Screen
Punch Adjustment Mode Screen Punch Horizontal Position Adjustment Screen
Three-Folding Position Adjustment Screen 2 Positions Staple Pitch Adjustment Screen
arrow key.

Key Operator Mode
Finisher Adjustment [17] (continued)
2 Touch [17] Finisher adjustment to display the Finisher Adjustment Menu Screen.
3 Touch the desired menu key to display the adjustment screen for each function.
4 Make fine adjustment on the screen, then touch RETURN to restore the Finisher
Adjustment Menu Screen.

Key Operator Mode
HDD Management Setting [18]
Use this function to manage the image data stored in the optional Hard Disk Kit
(DL6500020) and to check the space available for new data.
• Password list/delete: Display the password list on the screen, or delete the image data
(JOB) by deleting the corresponding password from the list.
• JOB auto delete period setting: Specify the period of time (1 to 52 weeks) to keep the
data. It will be deleted automatically when specified period has passed.
• State of HDD capacity: Check the space in percentage.
Key Operator Mode Screen 2 HDD Management Password Entry Screen
HDD Management Setting Menu Screen Password List/Delete Screen
Password List/Delete Screen JOB Auto Delete Period Setting Screen
State of HDD Capacity Screen

Key Operator Mode
HDD Management Setting [18] (continued)
Mode Screen.
arrow key.
2 Touch [18] HDD management setting. The HDD Management Password Entry Screen
will be displayed when the 4-digit HDD management password is set by service.
Otherwise, the HDD Management Setting Menu Screen displays without the password
requirement.
If the HDD Management Password Entry Screen is displayed, use the keypad on the
touch screen to enter your 4-digit HDD management password; then touch OK, to
display the HDD Management Setting Menu Screen.
NOTE: The HDD management password is not initially set. Contact your service representative, if desired.
3 Touch the desired menu key to display the subsequent screen for each function.
To view the password list or delete the password and the corresponding image data:
(1) Touch [1] Password list/delete to display the Password List/Delete Screen.
(2) Touch to highlight the password key to be deleted, then touch DELETE. The popup
menu will appear for confirmation.
(3) Touch YES to delete the selected password and all the corresponding data or touch
NO to cancel.
(4) Touch RETURN to return to the HDD Management Setting Menu Screen.
To delete the password and data automatically:

(1) Touch [2] JOB auto delete period setting to display the Job Auto Delete Period
Setting Screen.
(2) Touch Auto delete ON to highlight it, then enter the number of weeks to keep each
data, using the touch screen keypad. The maximum period of time is 52 weeks.
(3) Touch OK to complete the setting.
To check the current state of HDD capacity:

(1) Touch [3] State of HDD capacity to display the State of HDD Capacity Screen. The
bar chart on the screen shows the current state of HDD capacity.
(2) Touch RETURN to return to the HDD Management Setting Menu Screen.


Key Operator Mode
Non-Image Area Erase Setting [20]
Select the mode of Non-Image Area Erase function to be in effect when this feature is
selected on the Application Selection Screen after power is turned on or after Auto/Reset
occurs.
Key Operator Mode Screen 2 Non-Image Area Erase Setting Screen
arrow key.
2 Touch [20] Non-image area erase setting to display the Non-Image Area Erase Setting
Screen.
3 Select the desired erase mode and original density level.
Touch AUTO to let the machine select the erase mode and density level automatically.
To specify the erase mode manually, touch Oblique erase or Rectangle erase, as
desired, then select the density level required. Five exposure levels are provided.
4 Touch OK to complete the setting and restore the Key Operator Mode Screen.
NOTE: 1. If an invalid password is entered, enter the valid 4-digit password.

2. Select AUTO mode if the specified Oblique or Rectangle Erase mode does not function properly due
to the type of set original.

Key Operator Mode
Key Operator ECM Form
No. Password Count/Limit No. Password Count/Limit

DL650us14v1.fm 1 ページ２００１年１１月１４日　水曜日　午後４時３分
Section 14: Maintenance & Supplies
Loading Paper
Paper Indicator
Paper Empty Indicator
Using the Help Key
Loading Paper in Tray 1, 2, and 3
Loading Paper in LCC (9930/9932)
Loading Tabbed Sheets in Tray 1, 2, or 3
Loading Tabbed Sheets in LCC (9930/9932)
Adding Toner
Inserting a New Staple Cartridge into 9940/9922 Finisher
Empty Trash Basket of Punch Kit
Preventive Maintenance
Reading the PM Counter
Printing the PM Counter
Cleaning the Left Partition Glass
Cleaning the Document Glass and Cover
Maintenance & Supplies 14-1

Maintenance & Supplies
Loading Paper
Paper Indicator ( )
A paper indicator always appears on the tray key of the Basic Screen to indicate the paper
level.
Paper Empty Indicator ( or )
The Paper empty indicator flashes on the tray key of the Basic Screen when a tray is
empty. Add paper to the tray when the Paper empty indicator is flashing.
Do not exceed the following tray limits:

Tray 1: 500 sheets 20lb (430 sheets 24lb)
Tray 2: 500 sheets 20lb (430 sheets 24lb)
Tray 3: 1,500 sheets 20lb (860 sheets 24lb)
LCC: 4,000 sheets 20lb
Multi-sheet bypass tray: 100 sheets 20lb
(Do not load above the thick red line on rear guide.)
Using the Help Key
To learn how to load paper at any time, press [Help], then touch any tray to display
instructions on the touch screen. For details on tray position size vs. paper size, see
Section 4: Paper Information.
Before loading When placing a stack

paper, fan the of paper into the tray,
stack to prevent be sure to load it with
sheets from the curl turning up, i.e.,
sticking together. with concave side up.
See the following pages for instructions on loading paper in trays 1~3 and LCC.
14-2 Maintenance & Supplies

Loading Paper (continued)
Loading Paper in Tray 1, 2, and 3
When displaying Thick or Thin on the tray key of the Basic Screen, be sure to load the
specified paper; otherwise mishandled paper may occur.
When displaying TAB on the tray key of the Basic Screen, see p. 14-5.
1 Withdraw tray 1, 2, or 3, and open the paper feed roller.

2 Place paper on the tray with the curl side turning up.
Load size 11"x17", 8.5"x14", 8.5"x11", 8.5"x11"R or 5.5"x8.5" (user-adjustable)
Do not stack paper above the thick red line level.
2 Move the green lever (located at the left side) of the rear paper guide to the edge of the
paper.
3 When paper is seated properly, close the paper feed roller.
4 Push the tray back fully into the copier.
NOTE: Do not bump the tray into the main body; otherwise machine trouble may be caused.

Loading Paper in LCC (9930/9932)
When displaying Thick or Thin on the tray key of the Basic Screen, be sure to load the
specified paper; otherwise mishandled paper may occur.
When displaying TAB on the tray key of the Basic Screen, see p. 14-6.
1 Open the LCC top door.

2 Press the paper loading button to lower the LCC bottom plate.
3 Load the fixed size paper into the LCC with the paper curl turning downward.
4 Repeat the steps 2 and 3 until the bottom plate cannot go down any more.
Load size 8.5"x11" or A4 (service-adjustable) for 9930; or load size 11"x17", 8.5"x14",
8.5"x11", 8.5"x11"R, A3, B4, A4, A4R, or F4 for 9932.
Do not stack paper above the paper hook level.
5 Close the LCC top door.

Loading Tabbed Sheets in Tray 1, 2, or 3
Load offset tabbed sheets so that the tab extensions are on the left at the rear (not front) of
the tray. The tab extension width should be 0.5" (12.5 mm) or less.
When loading tabbed sheets in the tray, be sure to specify the paper type as TAB in the
Key operator mode; otherwise mishandled paper may occur. See p. 13-27 to p. 13-28.
The top sheet is designated face down as the first tab of the finished set. Subsequent
offset tab sheets follow in sequence.
Rear Example: 3 Tabbed sheets loaded in position for one finished set.
Front Section 3
1st TAB
Management
Printed Section 1
side Introduction 2nd TAB
3rd TAB
1st TAB
ONE FINISHED SET
2nd TAB 3rd TAB

Rear
Section 3
1st TAB
Front Section
Section 3
Management
3
Management
Section 1
Section 1 Section 1
Management
Introduction Introduction Introduction
3rd TAB
1st TAB 2nd TAB
2nd TAB 3rd TAB THREE FINISHED SETS

Loading Tabbed Sheets in LCC (9930/9932)
Load offset tabbed sheets so that the tab extensions are on the right at the rear (not front)
of the tray. The tab extension width should be 0.5" (12.5 mm) or less.
When loading tabbed sheets in the tray, be sure to specify the paper type as TAB in the
Key Operator mode; otherwise mishandled paper may occur. See p. 13-27 to p. 13-28.
The top sheet is designated face up as the first tab of the finished set. Subsequent offset
tab sheets follow in sequence.
Example: 3 Tabbed sheets loaded in position for one finished set.

Rear
1st TAB
1st TAB Section 1
Section 1
Introduction
Printed 2nd TAB
set 3rd TAB
Front
3rd TAB
ONE FINISHED SET

Rear
1st TAB 2nd TAB
1st TAB
2nd TAB Section 1 Section 1 Section 1
Introduction Introduction Introduction
Section 1
Section 1
Introduction
Printed Section 1
Introduction
Introduction
set
Front
3rd TAB 3rd TAB

THREE FINISHED SETS

Adding Toner
CAUTION
Keep toner cartridge away from children. Although the toner is non-toxic, do not inhale it or allow it to enter
your eyes. In case the toner comes in contact with eyes, please consult your physician.
When toner supply is low, the message “Please add toner” displays on the touch screen.
1 Open the Toner access door.

2 Pull the Toner cartridge holder lever forward and withdraw the Toner cartridge holder.
3 Remove the empty toner cartridge.
4 Shake the new Toner cartridge several times to loosen toner.
5 Remove the Toner cartridge cap.
6 Set the new Toner cartridge into the Toner cartridge holder.
NOTE: Align the rear part of the Toner cartridge with the Toner cartridge holder.
7 Push the Toner cartridge holder lever backward and return the toner cartridge holder to
its original position.
8 Close the Toner access door securely.

Inserting a New Staple Cartridge into 9940/9922 Finisher
Use only the staples supplied by us. Contact your service representative to reorder.
1 Open the Finisher door.

2 Pull out the stacker unit by holding the stacker unit handle.
3 Pull up the cartridge housing, then remove it while sliding it along the stapler rail.
4 Remove the empty cartridge from the cartridge housing.
5 Insert the new cartridge into the housing.
NOTE: Do not remove the staples remaining inside the housing; otherwise, the first sheet output after the
replenishment will not be stapled.
6 Insert the cartridge housing while sliding it along the stapler rail, then push down in to
secure it in place.
7 Return the stacker unit to its original position.
8 Close the Finisher door.

Empty Trash Basket of Punch Kit
When the trash basket becomes full, “Trash basket of Punch kit is full / Please empty trash
basket” message displays on the touch screen.
1 Open the Finisher door and withdraw the trash basket.

2 Empty the trash basket.
3 Return the trash basket to its original position, then close the Finisher door securely.

Preventive Maintenance
After a set number of copies have been made on your copier, Preventive Maintenance
(PM) will be required for maintaining optimal performance.
When preventive maintenance is due, a message will prompt you to contact your service
representative for maintenance.
Reading the PM Counter
Control Panel Counter List Screen

Help
Program Memory
Mode Check
Utility
Start
Proof Copy

2 Press [Mode Check] to display the PM count on the Counter List Screen.
3 Touch EXIT to return to the Basic Screen.
Printing the PM Counter

2 Press [Mode Check] to display the PM counter on the Counter List Screen.
3 Touch Counter list output. The Basic Screen will be displayed.
4 Touch the desired tray key to select the copy size.
5 Press [Start]. The counter list will be printed out, and the list print mode will be released.

Cleaning the Left Partition Glass
The glass partition at the far left of the platen glass is designed for real-time scanning from
the EDH. Keep this glass clean; otherwise soil marks may be copied, resulting in dark lines
on the copies.
Raise the EDH, and clean the left partition glass

with a clean soft cloth.
Cleaning the Document Glass and Cover

The platen glass and the inner surface of the EDH should be kept clean. Otherwise, soil
marks may be copied.
Raise the EDH, and clean the glass and inner

surface of the EDH with a clean soft cloth.
NOTES:
1. The glass may also be cleaned with a soft cloth
dampened slightly with water; or with an antistatic
cleaner recommended by your service representative.
2. Never use paint solvents, such as benzene or thinners,
to clean any portion of the copier.

DL650us15v1.fm 1 ページ２００１年１１月１４日　水曜日　午後４時５分
Section 15: Troubleshooting
Call for Service

Limited Use of the Copier in Trouble
Memory Overflow
Power OFF/ON Screen
Clearing Mishandled Paper
Copying Hints
Troubleshooting 15-1
Troubleshooting
Call for Service
CAUTION
A Call for Service message indicates a machine condition that requires the attention of
your service representative.
Call for Service Screen
1 Immediately make note of the Report code number indicated in the upper portion of the
screen.
2 Turn OFF the main switch and main power switch.
3 Unplug the machine.
4 Contact your service representative and report the condition and code number.
15-2 Troubleshooting
Troubleshooting
Call for Service (continued)
Limited Use of the Copier in Trouble
If the message shown below is displayed on the Call for Service Screen, you may continue
operating the copier on a limited function basis and utilize the trays and ADU that are not
affected by the trouble. To obtain this limited functionality of the copier, consult your service
representative. Be sure to utilize the limited function only temporarily, and arrange for
machine repair immediately.
1 If limited use of the copier is available, the following message is displayed in the
message area instead of the Report code.
Tray 1 failure
Press AUTO to select except this tray
2 Press [Panel Reset].
Please switch ON/OFF

E 18-2
3 Turn the power switch OFF, then ON.

A copying job can be continued without using the troubled portion of the machine (ex.
Tray 1).
CAUTION
EVEN IF THE COPYING JOB CAN BE CONTINUED WITH THE ABOVE OPERATION, IMMEDIATELY
CONTACT YOUR SERVICE REPRESENTATIVE WHEN THE CALL FOR SERVICE SCREEN IS
DISPLAYED.
Troubleshooting
Memory Overflow
In certain modes, the DL650 uses memory for convenience and to make operations flow
smoothly. Occasional memory overflow may occur if the installed memory is inadequate
for the copy conditions selected. Should memory overflow occur frequently, it is
recommended that you contact your service representative to extend the memory capacity
in your machine.
When memory overflow occurs, the following screen will be displayed to enable you to take
an appropriate measure for the current job situation.
Memory Overflow Management Screen
When memory overflow occurs while scanning the first job, the machine stops
immediately, and the screen provides JOB STOP and SCAN STOP as the only two
available options.
NOTE: If the job settings include Booklet mode, SCAN STOP will disappear.
• To delete all the scanned data and discontinue the job, touch JOB STOP.
• To give up further scanning but print out all the data already scanned into memory, touch
SCAN STOP.
When memory overflow occurs during the reserve operation, CONTINUE also appears on
the active screen. In this case, the machine will not stop until all the jobs on standby for
printing are completed.
• To delete the scanned data and discontinue the last reserve job, touch JOB STOP.
• To give up further scanning but print out the data already scanned for the last reserve
job, touch SCAN STOP.
NOTE: If the job settings include Booklet mode, SCAN STOP will disappear.
• To continue scanning the last reserve job, touch CONTINUE as the current printing job
gradually enables memory for new data.
Troubleshooting
Power OFF/ON Screen
When any trouble affects the electric signal of the copier, the Power OFF/ON Screen will
be displayed.
Power OFF/ON Screen
Troubleshooting
Clearing Mishandled Paper
CAUTION
When removing mishandled paper, be sure to leave no torn paper inside the machine,
avoid touching the drum or scratching it in any way, and keep all metal and magnetic
objects, e.g., watches, jewelry, etc. away from the drum area.
When a paper misfeed occurs, the copier stops making copies and mishandled paper
codes display on the screen to indicate misfeed area(s). A flashing code indicates the area
that should be cleared first. To view Help screen instructions, touch illustration explanation
when the flashing mishandled paper code displays. Be sure to remove paper from each
flashing location until all locations are cleared.
The following 18 mishandled paper codes display for specific areas of the machine.
Code Location Code Location

[1] : Tray 1 [10] : Main body
[2] : Tray 2 [11] : Main body
[3] : Tray 3 [12] : ADU or Main body
[5] : Tray 4 (LCC) [13] : Main body
[6] : Multi-sheet bypass tray [14] : EDH
[7] : Right side cover of Main [15] : EDH
body [16] : Finisher or Punch kit
[8] : Tray 4 (LCC) [17] : Finisher (Cover inserter)
[9] : Multi-sheet bypass tray and [18] : Finisher (Book making
Main body unit)
Troubleshooting
Clearing Mishandled Paper (continued)
WARNING:
The right rear area of the conveyance fixing unit generates high voltage. If touched,
electrical shock may occur. DO NOT TOUCH!
CAUTION:
The fixing unit is internally very hot. To avoid getting burned DO NOT TOUCH the area.
Use care when withdrawing the convayance fixing unit, and remove the mishandled paper
in the fixing unit.
CAUTION:
The conveyance fixing unit is heavy. Use care and draw it out gently; otherwise you may be
injured.
CAUTION:
DO NOT put your hand between the main body and developing fixing unit; otherwise you
may be injured.
CAUTION:
Inside the Booklet mode outlet is the roller drive unit. DO NOT put your hand into it when
removing the folded or stapled & folded sheet; otherwise you may be injured.
Troubleshooting
Copying Hints
COPIER DOES NOT OPERATE WHEN POWER SWITCH IS ON

Fully insert paper trays.
Close EDH.
Close Front doors and Toner access door of main body.
Close Finisher door.
Check to be sure main power switch is ON.
Check to be sure power plug is firmly inserted in electrical socket.
COPY IMAGE IS TOO LIGHT

Manually adjust copy density to darker density.
Check toner indicator and add toner, if required.
Check paper for dampness. Do not leave paper in copier when humidity is high.
Check to see if Photo, Text, or Increase Contrast mode is required.
Check the Density shift.
COPY IMAGE IS TOO DARK

Manually adjust copy density to lighter density.
Check to see if Photo, Text, or Increase Contrast mode is required.
Check the Density shift.
COPY IMAGE IS NOT CLEAN OR SHOWS SPOTS

Use clean originals since dirt marks may be copied.
Keep platen glass and inner surface of document cover clean.
Call for service if “Call for service” is displayed in the message area.
Check density indicator and lighten if required.
COPY PAPER MISHANDLES DURING COPYING

Fan copy paper and load it with curl side in proper location. Do not exceed the tray
capacity.
COPY IMAGE CAN BE RUBBED OFF

Check copy paper thickness. Use Thick paper mode, if paper weight requires it.
MAGNIFICATION CANNOT BE CHANGED

Reduce & Shift are incompatible with magnification.
Press [Panel Reset] and set desired copying conditions without using Reduce & Shift.
DUPLEX MODES CANNOT BE SELECTED

Fully close EDH, then select Duplex mode again.
Troubleshooting
Copying Hints (continued)

COPYING DOES NOT BEGIN AFTER PRESSING START
Insert or adjust the appropriate paper tray for copy size selected.
Close EDH firmly.
Close Front doors and Toner access door of main body completely.
Close Finisher door completely.
COPYING DOES NOT RESUME AFTER MISHANDLED PAPER IS REMOVED

Check copier diagram on touch screen for additional indications of mishandled paper.
COPY QUALITY IS POOR

Check paper for dampness, and replace it if necessary.
THE ORIGINAL PAPER IS MISHANDLED OR SKEWED IN THE EDH

Originals should conform to the recommended size and weight.
Be sure originals are not stapled.
Align originals evenly in the EDH.
Check to make sure paper guides meet the width of mixed size originals.
COPY IMAGE IS SKEWED WHEN BYPASS IS USED

Be sure copy paper is inserted straight.
USING ECM, COPIES CANNOT BE MADE AFTER PASSWORD IS ENTERED

Check to see if the message EXCEEDS LIMIT is displayed.
Contact Key Operator to reset limit.
FINISHER DOES NOT OPERATE

Press OUTPUT APPLI. key.
Check for a paper misfeed and remove it, as required. Properly close finisher door.
EDH INDICATOR WILL NOT LIGHT AFTER AUTO/RESET IS PRESSED

Fully close EDH.
EDH LIGHT IS FLASHING

The EDH is ready to accept originals.
Insert originals on EDH tray, press [Panel Reset], then [Start].
ADD TONER MESSAGE IS DISPLAYED

New toner supply is needed. Follow instructions for adding toner.
Troubleshooting
Copying Hints (continued)

CALL FOR PM IS DISPLAYED IN MESSAGE AREA
Contact your service representative for Preventive Maintenance.
APS SELECTS THE WRONG PAPER SIZE

Paper guides must be adjusted exactly to the size of originals.
IN MIXED ORIGINAL MODE, A MESSAGE TO LOAD A REQUIRED PAPER SIZE DISPLAYS,

EVEN THOUGH THAT SIZE IS LOADED IN ONE OF THE TRAYS
Paper sizes loaded in the trays must be consistent with the tray position size; otherwise,
the tray key on the Basic Screen will blink.
THE BASIC SCREEN DOES NOT DISPLAY SETTINGS AS DESCRIBED IN OPERATING

MANUAL
Check with the Key Operator, as Initial Settings may have been changed.
“PLEASE CHECK ORIGINAL”

This message displays when the copier detects a non-standard paper size on the platen
glass.
Select copy size and press [Start]. 1.000 magnification will be selected automatically.
If this message continues to display after selecting copy size, select 1.000 magnification,
even if it is already indicated, then press [Start]. If desired, ask your service representative
to enable the machine to default to 1.000 magnification in this situation.
SHEET INSERTION RESULT IS NOT AS EXPECTED

Blank insertion: Be sure manuscript originals do not already include blank sheets in the
locations designated for sheet insertion.
Copy insertion: To ensure that chapter sheets in 1-2 mode always appear on the right hand
side in the finished set, insertion sheets must be designated on the page setting screen
with odd numbers, not even. If required, make an even numbered original page odd by
inserting a blank sheet in front of that page, so that the blank sheet is even and the
insertion sheet is odd.
FINISHER STAPLE RESULT IS NOT AS EXPECTED

The 2 staple position functions only on copy paper that is loaded vertically (crosswise
style).
DL650us16v1.fm 1 ページ２００１年１１月１４日　水曜日　午後４時７分
Section 16: Machine Specifications
Specifications
Machine Specifications 16-1

Specifications
Product Name DL650
Configuration Console with stationary platen
Photoreceptor OPC drum
Method Laser Electrostatic
Toner Black, cartridge type
Recommended Operating Environment 50°~86°F (10°~30°C); 10~80% RH
Warm Up Approx. 6.0 min. @68°(20°C); 50% RH
Panel Reset Off/30 sec./1 min./1.5 min./2 min./2.5 min./3

min./3.5 min./4 min./4.5 min./5 min.
First Copy Out Time From Platen Glass:

3.1 sec. for 8.5"x11"
Copy Rate 65 cpm: 8.5"x11", 5.5"x8.5"

53 cpm: 8.5"x11"R
44 cpm: 8.5"x14"
37 cpm: 11"x17"
Continuous Copy 1~9,999 copies
Voltage 120V±10% 16A 60Hz±2.5Hz
Grounding Isolation recommended
Power Consumption Max. 1,920 VA (full option)
Noise Level (full system) Approx. 78 dB (A) or less, during copying
Automatic Modes AMS; AES (plus 9-level manual density);

APS detects 11"x17", 8.5"x14", 8.5"x11"R,
8.5"x11", 5.5"x8.5"
Magnification Presets; 0.500, 0.647, 0.733, 0.785, 1.214,
1.294, 1.545, 2.000
3 User Sets - 0.250~4.000, set by Key
Operator
Zoom range - 0.250~4.000 in 0.1% steps
Originals on Platen Max. size: 11"x17" (280mm x 432mm)
Specifications Subject To Change Without Notice

16-2 Machine Specifications
Specifications
Originals in Document Handler Simplex originai mode: 1>1; 1>2
11"x17"; 8.5"x14"; 8.5"x11"R; 8.5"x11";
5.5"x8.5"
Max. 100 sheets (20 lb) feed/exit capacity
Duplex original mode: 2>2; 2>1
11"x17"; 8.5"x14"; 8.5"x11"R; 8.5"x11";
5.5"x8.5"
Mixed mode:
11"x17"+8.5"x14"+8.5"x11"+5.5"x8.5"
or 8.5"x14"+8.5"x11"R, 8.5"x11", 5.5"x8.5"
Original weight:
13~34 lb bond; curl max. 10 mm or less
(Transparency, Paste-up, Offset master, Labels,
& Intermediate papers unavailable)
Paper Source Main body trays 1/2/3; 500/500/1,500 sheets
LCC tray 4; 4,000 sheets
Multi-sheet bypass tray; 100 sheets
Tray 1/2/3 user adjustable
LCC adjusted by your service representative
Paper Exit Tray 100 sheets (20 lb)
Paper Weight 16 lb~24 lb bond recommended
(Max. range: 16 lb~110 lb (200g/m2 thick paper)
in 1-2 or 2-2 copying, 13 lb~15 lb in 1-1 or 2-1
copying)
OHP sheet, Transparency, Labels, Tab, 3-hole
Main Body Safety Standard UL 1950; CSA 22.2 No. 950 -93
Radio Interference FCC Rules part 15, sub-part B Class A

Specifications
Options Finisher (9940/9922)
9924 Cover Inserter
Punch Kit
Large Capacity Cassette (LCC) (9930/9932)
64MB Memory (M64-1) / 128MB Memory
(M128-1)
Printer Controller
Hard Disk Drive Kit (DL6500020)
Machine Weight 444 lb (201.5 kg)
+25 lb (11.5 kg) w/EDH
+121 lb (55 kg) w/9940 Finisher
+143 lb (65 kg) w/9922 Finisher
+23 lb (10.5 kg) w/9924 Cover Inserter
+4.4 lb (2 kg) w/Punch Kit
+66 lb (30 kg) w/LCC (9930)
+93 lb (42 kg) w/LCC (9932)
Machine Dimensions Main Body (with EDH)

Width: 25.6 in. (650mm)
Depth: 31.1 in. (790mm)
Height: 44.9 in. (1140mm)
Document Handler (EDH)
Width: 23.6 in. (600mm)
Depth: 22.4 in. (570mm)
Max. open angle: 70±5°
Finisher (9940/9922)
Width: 25.8 in. (656mm)
Depth: 25.8 in. (656mm)
9924 Cover Inserter
Width: 20.1 in. (511mm)
Depth: 24.4 in. (620mm)
Punch Kit
Width: 2.7 in. (68mm)
Depth: 17.4 in. (442mm)

Specifications
Automatic Duplex Unit (ADU) Paper size: 11"x17", 8.5"x14", 8.5"x11",
5.5"x8.5"
Paper weight: 16~110 lb (200g/m2 thick paper)
Non-stack type
Finisher (9940/9922) Power source: Main body
Non-sort/Sort/Group mode:
500 sheets 5.5"x8.5"R
3000 sheets 8.5"x11"/R (9940 Finisher)
2500 sheets 8.5"x11"/R (9922 Finisher)
1500 sheets 11"x17", 8.5"x14"
Size 11"x17" ~ 5.5"x8.5"R
Staple-sort mode:
1000 sheets*
Size 11"x17" ~ 8.5"x11"/R, 5.5"x8.5"
* Variable according to the number of pages to
be stapled. See p. 4-7 or p. 4-8 for detail.
Folding/Stapling & Folding mode (9922 only):
100 sheets (11"x17", 8.5"x14")
75 sheets (8.5"x11"R, A4R)
Size 11"x17", 8.5"x14", 8.5"x11"R, A4R
(8.27"x11.69", 210mm x 297mm)
* The maximum number of sheets varies,
depending on the number of pages in the
booklet and whether Folding or Stapling &
Folding is selected. See p. 4-10.
Three-Folding mode (9922 only):
50 sheets (folding one sheet in three)
Size 8.5"x11"R, A4R (8.27"x11.69", 210mm x
297mm)
Staple Cartridge 5000 staples/cartridge

Specifications
9924 Cover Inserter Power source: Finisher
Paper size:
Upper tray 8.5"x11", 8.5"x11"R, 5.5"x8.5", A4,
A4R (8.27"x11.69", 210mm x 297mm)
Lower tray 11"x17", 8.5"x14", 8.5"x11",
8.5"x11"R, 5.5"x8.5", A4, A4R (8.27"x11.69",
210mm x 297mm)
Paper weight in cover sheet mode: 13 ~ 110 lb
(200g/m2 thick paper)
Paper weight:
Manual stapling: 13 ~ 110 lb (200g/m2 thick
paper)
Manual punching: 13 ~ 45 lb
Manual stapling & folding: 16 ~ 110 lb (200g/m2
thick paper)
Manual three-folding: 20 lb
Punch Kit Paper size: 11"x17", 8.5"x11"
Paper weight: 16~45 lb
Number of holes: 3 holes
Hole diameter: 0.315" ± 0.020" (8mm ± 0.5mm)
Hole pitch: 4.252" ± 0.020" (108mm ± 0.5mm)
Weight: 4.4 lb (2 kg)
Power source: Finisher
Large Capacity Cassette (9930) Paper type: Plain paper (13~110 lb (200g/m2
thick paper))
Paper size: 8.5"x11", A4
Dimensions: Width 16.9 in (430 mm)
Depth 25.2 in (639 mm)
Height 27.2 in (690 mm)
Weight: 66 lb (30 kg)
Power source: supply from main body
Large Capacity Cassette (9932) Paper type: Plain paper (13~110 lb (200g/m2
thick paper))
Paper size: 11"x17", 8.5"x14", 8.5"x11",
8.5"x11"R, A3, B4, A4, A4R
Dimensions: Width 26.4 in (670 mm)
Depth 25.2 in (639 mm)
Height 27.4 in (695 mm)
Weight: 92.4 lb (42 kg)
Power source: supply from main body

DL650usindexv1.fm 1 ページ２００１年１１月１４日　水曜日　午後６時４９分
Index
Index 1
Index
Number Combination 9-10
1 SHOT indication time 13-47 Continuation print 13-47
1s1, 1s2, 2s1, 2s2 6-8 Control panel 3-3
1s2 Copy Mode Using Platen Glass 6-9 Control Panel Adjustment 13-40
2 in 1, 4 in 1, 8 in 1 9-10 Control Panel Layout 3-12
2 Repeat, 4 Repeat, 8 Repeat 9-27 Conveyance/Fixing unit 3-4
9924 Cover Inserter 3-3, 7-20 Copier counter 5-8
9930/9932 Large Capacity Cassette 3-3, 3-9 Copier Initial Setting 13-13
9940/9922 Finisher 3-3, 3-6 Copy Density 6-13
9940/9922 Finisher Specifications 7-2 Copy Limit 13-20
Copy Mode 6-7
A Copy Mode Using EDH 6-8
ADD PAPER key 6-34 Copy Size 6-23
Adding Toner 14-7 Copying Hints 15-8
AES key 6-13 Counter List 5-8
All-Image Area 9-33 Counter start date 5-8
AMS key 6-23 Cover inserter control panel 3-8
An interruption suspend way 13-48 Custom key (Lens Mode) 13-17
APPLI. key 9-2
Application Function Menu 9-2
D
Application Selection Screen 9-2 DANGER 2-2
APS key 6-23 Darker (Copy Density) 6-13
Arrow key change (Image Shift) (Memory Switch) 13-48 Date & Time Setting 13-7
AUTO Layout 9-31 DATE/TIME (Stamp) 9-39
Auto Low Power 5-2 Delete of overlay image 13-49
Auto select of Booklet copy 13-47 Density Shift 6-14
Auto Shut-Off 5-4 DIMM (memory) 11-2
Automatic Exposure Selection (AES) 3-14, 6-13 Drum unit 3-4
Automatic Magnification Selection (AMS) 3-14, 6-17
Automatic Paper Selection (APS) 3-14, 6-16
E
Automatic Tray Switching (ATS) 3-14 E.C.M. All Count Reset 13-24
Automatic tray switching (Memory Switch) 13-46 E.C.M. Data Edit 13-20
E.C.M. Function Setting 13-25
B E.C.M. management list 13-50
Back Cover Mode 9-4 E.C.M. password (Memory Switch) 13-47
Basic Screen 3-13, 6-2 E.C.M. password input timing 13-48
Binding Mode 6-27 ECM (Electronic Copy Monitor) 13-18
Book copy 9-19 ECM Master Key Code 3-15, 13-19
BOOK MARK key 6-44, 9-2 ECM password 5-5, 13-20
Booklet 9-12 ECM Setting Menu Screen 13-19
Booklet mode outlet 3-6 EDH (Electronic Document Handler) 3-3
Booklet tray 3-6 EDH AMS 13-46
Bookmark function 13-48 EDH APS 13-46
EDH frame erasure selection 13-46
C EDH original size detect 13-46
[C] (Clear) key 3-12 EDH Store Mode 6-37
Call for Service 15-2 EDH-Original effect 13-45
Call Remote Center 13-51 E-Mail Transmission Setting 13-11
Cartridge housing 3-7 Empty Trash Basket of Punch Kit 14-9
CAUTION 2-2 Energy Saver key 3-12, 5-6
Change page no. pos. (booklet) (Memory Switch) 13-48 Energy Saver Mode 5-2
Chapter 9-8 Energy saver screen 13-47
Check Mode and Proof Copy 6-43 Energy Saver Setting 13-42
Cleaning the Document Glass and Cover 14-11 Entering an ECM Password 5-5
Cleaning the Left Partition Glass 14-11 Erasure outside area of original 13-46
Clearing Mishandled Paper 15-6 Exit direction 13-49
2 Index
Index
Exit direction of 1 sheet 13-48 J
External Machine 3-2 JAM key 6-33
Job offset operating 13-47
F Job Recall 10-4
Face Down Exit 7-27 Job Status Screen 6-30
Face Up Exit 7-30 Job Store 10-2
FCC Regulations 2-12
Finisher Adjustment 13-53 K
Finisher Capacity Requirements 2-10 Key click sound 13-47
Finisher door 3-6 Key click sound (No paper/JAM) 13-48
Finisher mode by Full-auto 13-45 Key counter 3-3
Finisher Paper Capacity 3-15 Key Operator Data Setting 13-30
Fixing unit 3-4 Key Operator Mode 13-2
Folder keys 6-2 KEY OPERATOR MODE key 6-46
Folding mode 7-13 Key Operator Password 3-15, 13-2
Font pattern list 13-50 Keypad 3-12
Frame/Fold Erasure 9-29
FREE JOB key 6-28 L
Front Cover Mode 9-4 Label Locations 2-3
Language Select Setting 13-9
G Laser Safety 2-12
Gateway address 13-10 Laser safety label 2-16
Group Mode Using Primary (Main) Tray 7-10 LCC (Large Capacity Cassette) 3-3
LCC bottom plate 3-9
H LCC top door 3-9
HDD 9-46, 11-2 LCD touch screen 3-3, 3-12
HDD Management Password 3-16 Lead Edge Delete 3-15
HDD Management Setting 13-55 Lens Mode 6-16
HDD STORE key 11-8 Ligher (Copy Density) 6-13
Help key 3-12, 6-46 Limited Use of the Copier in Trouble 15-3
Help Menu Screen 6-46 Line speed setting 13-10
Help Mode 6-46 Loading Paper 14-2
Help Screen 6-46 Loading Paper in LCC 14-4
How to Make a Basic Copy 6-2 Loading Paper in Tray 1, 2, and 3 14-3
Loading Tabbed Sheets in LCC 14-6
I Loading Tabbed Sheets in Tray 1, 2, or 3 14-5
ICES Regulations 2-12 lock icon 10-3, 13-26
Image Insert 9-17 Lock/Delete Program Memory 13-26
Image Recall Mode 11-10 Lunch Hour Off Setting 13-38
Image recalled cont. (SRV) 13-49
Image Shift 9-34 M
Image Store&Output Mode 11-8 Machine Condition Information 5-9
Image Store/Delete mode 11-4 Machine Configuration 3-2
Image stored cont. (SRV) 13-49 Machine Handling and Care 2-8
Increase Contrast Mode 8-4 Machine Installation and Power Requirements 2-6
Initial by Key counter insert 13-46 Machine Management List Print 13-50
Initial Settings 3-14 Main power switch 3-3
Inserting a New Staple Cartridge into 9940/9922 Finisher 14-8 Manual Finishing 7-23
Insertion Mode 9-4 Manual Low Power 5-3
Internal Laser Radiation 2-13 Manual Organization 1-3
Internal Machine 3-4 Manual Shut-Off 5-4
INTERRUPT indicator 6-38 Memory indicator 6-2
INTERRUPT key 3-12, 6-38 Memory Overflow 15-4
Interrupt Mode 6-38 Memory Switch Setting 13-43
IP Address Setting 13-10 Mishandled Paper During the Reserve Setting 6-33
Mixed Original 8-6
Index 3
Index
Mode Check key 3-12, 6-43 Platen APS 13-46
Mode Check Screen 6-43 Platen orig. size detect (SMALL) 13-47
Mode key 3-12, 11-5 Platen original size detect 13-46
Multi-sheet bypass tray 3-3 Platen Store Mode 6-35
PM Counter 14-10
N Positioning Mixed Originals 4-5
Non STD size (Key Operator mode) 13-28 Positioning Originals on the Platen Glass 4-2
Non STD size (Multi-sheet bypass tray) 6-25 Power OFF/ON Screen 15-5
Non STD Size (Special Original) 8-9 Power switch 3-3, 3-12
Non-Image Area Erase 9-23 Preset and Custom Zoom Ratios 6-20
Non-Image Area Erase Setting 13-57 Preventive Maintenance 14-10
Non-Sort Mode Using Primary (Main) Tray 7-5 Primary (Main) tray 3-6
Normal (Copy Density) 6-13 Printer counter 5-8
NORMAL key 6-13 Product Overview 1-4
Program Job 9-21
O Program Memory 10-2~10-7
Optional Equipment 1-11, 3-5 Program memory auto recall (30) 13-45
Orig. direction/binding mode 13-49 Program Memory key 3-12, 10-3
Original count 6-2 Proof Copy key 3-12, 6-43
Original Direction 8-3 Punch Kit 3-7
Original Form 8-9 Punching Mode 7-16
OUTPUT APPLI. key 7-8
Output Mode for Machine without Finisher 7-26 R
Output Mode Screen 7-8 RE key 6-20
Output Modes Using Secondary (Sub) Tray 7-11 Recalling Previous Job Settings 6-6
Overlay 9-44 Reduce & Shift 9-37
Overlay Memory 9-46 Remote Diagnostics 13-51
Ozon Release 2-17 Repeat Image 9-26
Report code 15-2
P Reserve 6-28
Page Design 1-3 Reserve copy function 13-48
PAGE NUMBERING 9-39 Reverse Image 9-25
Page space 9-34 RIGHT&LEFT BINDING key 6-27
PAGE SPACE key 9-36 Rotation 6-40
Panel Contrast / Key Sound Adjustment 13-29 Rotation (Memory Switch) 13-47
Panel Reset key 3-12 Rotation and AMS 6-41
Panel Reset key function 13-45 Rotation and APS 6-40
Panel Reset Mode 3-14 ROTATION OFF key 6-42
Panel reset timer 13-45 Routine Safety 2-9
Paper Capacity for Staple-Sort Mode 4-9
Paper empty indicator 14-2 S
Paper in 9930 4-7 Scan stop by a pull out tray 13-48
Paper in 9932 4-7 SCAN/SERVER LED 11-5
Paper in 9924 Cover Inserter 4-11 Secondary (Sub) tray 3-6
Paper in 9940/9922 Finisher 4-9 Select tray when APS cancel 13-46
Paper in Automatic Duplex Unit 4-8 Selecting a Special Ratio for Non-Standard Paper 6-18
Paper in Main Body Trays 4-6 Selecting Paper Type/Size for Multi-Sheet Bypass Tray 6-24
Paper in Multi-Sheet Bypass Tray 4-8 Server Function 11-2
Paper in Punch Kit 4-12 Service Settings 3-15
Paper indicator 14-2 SET NUMBERING 9-39
Paper loading button 3-9 Set Reserve Job 6-28
Paper Type / Special Size Set 13-27 Setting Job During Warm-up 6-4
PAPER TYPE/SIZE key 6-23, 6-24 Sheet/Cover Insertion 9-3
Paper Weight Compatibility Chart 4-12 Shortcuts 12-2~12-10
Photo Mode (Enhance) 8-4 Side 2 Lens Adjustment 13-52
Platen AMS 13-46 Side 2 print (STD repeat + zoom) 13-48
4 Index
Index
Site Requirements 3-10 U
SORT key 7-6 Unsuitable EDH Originals 4-3
Sort Mode Using Primary (Main) Tray 7-6 UP BINDING key 6-27
SPECIAL ORIGINAL key 8-2 User Density Level 1 Setting 13-15
Special Original Screen 8-2 User Density Level 2 Setting 13-16
Special Ratio Table 6-19 User Instructions 2-2
Stacker unit 3-7 User Lens Mode Ratio Setting 13-17
Stamp 9-39 User management list 13-50
Standard Equipment 1-11 User Setting Mode 13-15
Staple mode reset-function 13-47 Using the Multi-Sheet Bypass Tray 6-11
Staple Sheet Capacity 3-16 Using the Electronic Document Handler (EDH) 4-3
STAPLE SORT key 7-8 Utility key 3-12, 5-8
Staple-Sort Mode Using Primary (Main) Tray 7-7
Stapling & Folding mode 7-13 V
Start key 3-12 Vertical/Horizontal Zoom 6-22
Start key latch function 13-47
STATUS key 6-30 W
STD size (special) (Key Operator mode) 13-28 Warm-up Screen 6-4
STD size (special) (Multi-sheet bypass tray) 6-25 WARNING 2-2
Stop key 3-12 WATERMARK 9-39
Stop key function 13-47 WATERMARK NUMBERING 9-39
STORE key 6-35, 6-37 Weedly Timer Function 5-6
Store Mode 6-35 Weekly Timer 13-31
Subnetmask 13-10 Weekly Timer Master Key Code 3-15
System Initial Setting 13-7 Weekly Timer master key code 13-32
Weekly Timer On/Off Setting 13-33
T Wide paper (Key Operator mode) 13-28
Tab paper (Special Original) 8-9 Wide paper (Multi-sheet bypass tray) 6-26
Tabbed sheets 6-12 Work table 3-3
Text Mode (Enhance) 8-4 WWW Server Function 5-9
Text/Photo Enhance 8-4
Three-Folding Mode 7-18 Z
Timer Action On/Off Setting 13-36 Z-Folded Original 8-8
Timer indicator 3-12, 5-6 ZOOM key 6-18, 6-21
Timer Interrupt 5-6 Zoom Mode 6-21
Timer Interrupt Password Setting 13-39
Timer Setting (Weekly Timer) 13-34
Timer which prohibits Print 13-48
To Release Automatic Rotation 6-42
To Stop Scanning/Printing 6-5
To the User 1-2
Toner access door 3-3
Toner cartridge 3-4
Toner cartridge holder lever 3-4
Total counter 3-4, 5-8
Touch Screen 3-13
Transparency Interleave 9-15
Trash basket 3-7
Tray 1, 2, 3 3-3
Tray Auto Select Setting 13-41
Index 5
TM
www.imagistics.com
Imagistics International Inc.
100 Oakview Drive
Trumbull, CT 06611
©Imagistics International Inc. 2002

Printed in USA
Part Number DL65000030
The information contained in this

manual is subject to change without
notice to incorporate improvements
made to the products listed in this
manual.

Dl650 Op Guide

Uploaded by

Copyright:

Available Formats

Dl650 Op Guide

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Dl650 Op Guide

Uploaded by

Copyright:

Available Formats

www.imagistics.

ENERGY STAR® Program

Auto Low Power

Automatic Duplex Copying

Description/Order Name How much to Description

Printpowder® Toner 1 Carton Contains 8 toner cartridges

Copier Paper (8 1/2” x 11”) 10 Cartons Contains 5,000 sheets

Copier Paper (8 1/2” x 14”) 2 Cartons Contains 3,000 sheets

Copier Paper (11” x 17”) 2 Cartons Contains 2,500 sheets

3-Hole Punched 2 Cartons Contains 5,000 sheets

Transparencies 1 Box Contains 100 sheets

Developer* 1 Carton Contains 1 bag per carton

Staples for 9922 Finisher: 1 Carton Contains (3) 5,000 staple

*Note: This item can only be installed by an Imagistics customer Service

Section 2: Safety Information

Section 3: Machine Information

Section 3: Machine Information (continued)

Section 4: Paper Information

Section 5: Copier Management

Section 6: Basic Operations

Section 6: Basic Operations (continued)

Section 7: Output Modes

Section 8: Special Original

Section 10: Program Memory

Section 11: Server Function

Section 12: Shortcuts

Section 13: Key Operator Mode

Section 14: Maintenance & Supplies

Section 15: Troubleshooting

Section 16: Machine Specifications

Key Operator Functions

Copier Service, Repairs & Supplies

Control Panel with Interactive Touch Screen

To the User (continued)

Overview of the Operating Manual

Features of the DL650

• AES - Automatic Exposure Selection

• AMS - Automatic Magnification Selection

• APS - Automatic Paper Selection

• ATS - Automatic Tray Switching

• Auto Low Power

Features of the DL650 (continued)

Features of the DL650 (continued)

• Lens Mode (Preset, Zoom)

• Machine Status Confirmation

• Non-Image Area Erase

• Non STD Size for Multi-Sheet Bypass Tray

• Non STD Size for Original

Features of the DL650 (continued)

• Output mode for Machine with 9940/9922 Finisher Installed:

Features of the DL650 (continued)

• Punching Mode for 9940/9922 Finisher with Punch Kit Installed:

• Rotation Exit (Rotation Sort/ Rotation Group)

• Server Function (option)

Features of the DL650 (continued)

• STD Size (Special)

• Userset Density (USERSET 1, USERSET 2)

• Wide Size Paper

Stapler Finisher (9922)

Copier Features (continued)