1.

Function Descriptions
Race Panel Manual Gear Indicator
RPM Indicator Engine Temp.

RPM Up

OLED
Display Exit(>2s) / Enter

Down

MAP Select Pit Lane

Malfunction Light Launch Control
Traction Control
2. System Diagram

Race Panel

Lap Receiver(option) aRacer ECU

GPS Module(option)
aRacer Race Switch
aRacer Function Box(option)
 3. Monitor 4. Settings

Press or
Line 1 can select the variables Line 1 Press into setting
as listed below. page. Press and hold
for 2 second can go
Line 2 Line 2 back to the monitor.

Line1 display RPM, gear number, engine temp. only.

Line2 display the selectable variables as listed below.

Attention： Lap Time function only work with aRacer GPS

Module in GPS mode or Lap Receiver in IR mode Lap Time： Sequence Display
Settings Compare Best Lap
Display Description Receive Lag Time
Display Lag Time
299kmh 1 1:45.20 Speed, Lap Number, Lap Time Display Dif Time
Clear Record
299kmh WAF 12.8 Speed, WAF：Wide band O2 A/F

INJ：Fuel Injector usage rate, Shift Indicator： Shift RPM: Set shift RPM
INJ 85% Bat 13.3 Bat：Battery Volt. Indicator Step: Set LED Step
TPS：Throttle%,
TPS100% SA 30 SA：Spark angle Gear Indicator：ON/OFF Gear Indicator
TAir：Air Temp., Map Select：Select Map M1~M3
TAir 25c At 100 At：Atmospheric Pressure TCS Level：Select TCS 0~7
O2AD：Quick Shift AD, Launch Control：Set Launch Control RPM
O2AD 525 QS OFF Speed Source：Select ECU or GPS
QS：Quick Shift Detect(ON= Cut)
Malf Code：Malfunction Code Read
CL -12% WAF 12.8 CL：Close loop fuel correction%,
WAF：Wide band O2 A/F
WBO2：Wideband AFR Close Loop correction,
WBCL=0 WBAT=0 WBAT：Wideband AFR AutoTune (1:ON, 0:OFF)

Misc：Crank error count

MisC 0 ISC 30% ISC：Idle Speed Control%
4.1 Lap Time 4.2 RPM Indicator
Attention： Lap Time function only work with
aRacer Function Box in GPS mode or Lap
Receiver in IR mode.

Attention： GPS Lap Time function only

work with aRacer Function Box without Lap
Receiver.

4.1.1 Sequence Display 4.2.1 First LED ON RPM

Show the time, maximum engine temperature, maximum RPM, Set the first LED turn on RPM.
minimum RPM, maximum speed by lap sequence.

4.1.2 Compare Best Lap

Show the time difference vs. best lap. 4.2.2 Last LED ON RPM
Set the last LED turn on RPM, and when rpm is more than
4.1.3 Receive Lag Time this value, all LEDs will flash.
The delay seconds to stop receiver after passing check point, to
prevent double received. The default value is 10 seconds, 1 to 20
seconds is adjustable.

4.1.4 Display Lag Time For Example：

The delay seconds to display the lap time after passing the check First LED ON RPM = 7300 10000
point. The default value is 10 seconds, 1 to 20 seconds is adjustable. Last LED ON RPM =10000 9700
9400
9100
4.1.5 Display Dif Time 8500
8800
8200
Select the time difference vs. last lap or best lap while passing the 7900
7600
check point. 7300

4.1.6 Clear Record

Clear all records.
4.3 Gear Indicator 4.3 Map Select
This item can set line1 screen of gear indicator. If ON will This item can set the Map number of ecu, and the LED
show the gear number. If OFF will hide the gear number. will turn on.
This gear number is form aRacer ECU. If the ecu do not
have correct setting, gear number will be incorrect.

Line 1

Line 2
The calibration parameters in the table below can be set
separately at each Map.

Map Select Calibration Parameters Description

D3Race_AFR Race Mode target AFR
Attention： If the engine is stall, Gear number
is ”-”. Please check gearbox is in neutral position Race Mode D2Race_AFR_Power Race Mode target AFR at WOT
before start the engine. (M1) D3SA_TPS_Offset_Race Race Mode SA comp.
D3Eng_Brake_Race Race Mode engine brake level
D3Sport_AFR Sport Mode target AFR

Sport Mode D2Sport_AFR_Power Sport Mode target AFR at WOT

(M2) D3SA_TPS_Offset_Sport Sport Mode SA comp.
D3Eng_Brake_Sport Sport Mode engine brake
D3ECO_AFR ECO Mode target AFR

ECO Mode D2ECO_AFR_Power ECO Mode target AFR at WOT

(M3) D3SA_TPS_Offset_Eco ECO Mode SA comp.
D3Eng_Brake_Eco ECO Mode engine brake
4.4 TCS Level 4.6 Speed Source
This item can set the TCS Level of ecu. If turn off the TCS, This item can set speed source of Race Panel.
TCS LED will turn on.
Attention： GPS Speed only work with aRacer
Attention： TCS function only work with aRacer Race Module & Function Box
Race Module & aRacer Function Box

4.5 Launch Control 4.7 Malf Code

This item can set the Launch control RPM of ecu. Race Panel can show the malf code if EFI malfunctions
happen.
Attention： Launch Control only work with Attention： Some malfunction code is just
aRacer Function Box and Race Switch or Race detected in engine run.
Module
Attention：Malfunction Indicate Light (MIL)
•How to enter the MIL mode: In key on status, key off /on 3 times within 5. Note
3 sec and key switch is on at last time. The MIL will flash 2 times to
indicate it is in MIL flash mode.
•The all malfunction flash code combine two numbers. The flash code
example is as following: if flash code is “35”, after MIL flash indicate the
starting “02” and then the MIL will flash number “3” code first (the
interval time is 1.5sec) and delay 1.5sec to flash number “5” code (the
interval time is 0.5sec). After 4sec, MIL will start to flash next
malfunction code or repeat the only one malfunction code.
Attention：Clear Malf Code & Learning Value (Reset ECU)
In key on status, key off / on 10 times within 15 sec and then MIL will
flash “20” to indicate it is clear mode. Turn off key again, the learning
value and malf code will be cleared.
Malf Code Description Malf Light
Map sensor(Manifold Air Pressure) value is
P0106 AP Ration 14
incorrect
P0107 AP Open Map sensor broken wire 13
P0108 AP V Map sensor short to battery 13
P0112 T-A GND Intake air temperature sensor short to ground 22
P0113 T-A Open Intake air temperature sensor broken wire 22
P0117 T-Eng GND Engine temperature sensor short to ground 28
P0118 T-Eng Open Engine temperature sensor broken wire 28
P0122 TPS Open TPS broken wire 15
P0123 TPS V TPS short to battery 15
P0231 Pump Open Fuel pump broken wire 11
P0232 Pump V Fuel pump short to battery 17
P0261 INJ Open Injector broken wire 39
P0262 INJ V Injector short to battery 39
P0263 INJ Over Injector usage rate is too high (>90%) 53
P0298 Eng Over T Engine temperature over heat 35
P0335 CRK Err Crank sensor error 34
P1335 CRK Open Crank sensor broken wire 12
P0351 IGN V Ignition coil short to battery 33
P1351 IGN GND Ignition coil short to ground 33
P0563 Batt Vhigh Battery voltage is too high 46
P1500 Roll Act Rollover switch is triggered 49