Salahaddin University — Erbil 284 Semester Final Exam Date: Sunday, June 03, 2018 College of Engineering Time: 3 hours Petroleum and Chemical Eng. Fins Apenge Subject: Eng, Drawing & Descriptive Deparment Baan Geometry I Class: First Year Lecturer: Hardi A. Sivaily Q1/ The following figure shows the isometric view of a machine block, Draw: (30 Marks) i Full sectional view from front & ii / Full sectional side view. 2 A (Note: All dimensions are in millimeter) i) 4: Zs Q2/ A: A top view of a 75 mm long line AB measures 65 mm, while the length of its front view is 50 mm. Its end A is in the H.P. and 12 mm in front of the V.P. Draw the projections of AB and determine its inclination with HP. and the VP. (15 Marks) B/T.V. of 275 mm long Line CD, measures 50 mm. End C is in Hp and 50 mm in front of V.P. End D is 15 mm in front of V.P and it is above H.P. Draw projections of CD and find angles with H.P and V-P. (15 Marke) Page 1 of 2Q3/ Draw the Front, Side and to, view of the following figure. (40 Marks) ! (Note: All dimensions are in millimeter) Page 2 of 2ee Salahaddin University - Erbil Second Attempt Date: September 09, 2018 College of Engineering 2017-2018 ‘Time: 3 hours Petroleum and Chemical Eng. Department Subject: Eng. Drawing & Descriptive Geometry I Class: First Year Lecturer: Hardi A. Siwaily Qh (G0 Marks- Equally divided) Draw the orthographic projections of the following points: Point A, 25 mm above HP, 20 mm behind VP. Point B, 15 mm below HP, 25 mm behind VP. Point C, 30 mm below HP, 40 mm in front of VP. Point E, on HP, 35 mm behind VP. Point F, on VP, SO mm below HP. yaene Q2: (@0 Marks- equally divided) A/ Draw a regular Pentagon having a side length of 50 mm. B/ Use four-centerd method to construct an Ellipse having major and minor axises AB= 140, CD=80 mm, respectively. Q3: (30 Marks) Draw the following view of the Trip-Lever with original domensions. (Note: Alll dimensions are in millimeters) Page 1 of 2Q3: (20 Marks) Draw the following view of the C-Wrench with original domensions. (Note: All dimensions are in millimeters) Page2 of 2Salahaddin University - Erbil 2% Semester Midterm Examination Date: April 29, 2018 College of Engineering 2017-2018, Petroleum and Chemical Eng. Dept. (Class: First Year Time: 3 hours ‘Subject: Eng. Drawing & Descriptive Geometry Il Lecturer: Hardi A. Siwaily Q1: 0%) (Equally divided) Line H-E is 80 mm long, Its end H 10 mm below H.P and 15 mm behind V.P. The length of its top view (LTV) is 50 mm and its 40° inclined with x-y, while the P.V is inclined 55°. Draw the projections of the line and find the length of fron view (L.F.V) and inclinations of True Length with both H.P and V.P. Bz Line AB 100 mm long is inclined to HP at 45 deg. and inclined to VP at 30 deg. If the end A is on both HP and F-P. Draw front and top views of line and determine their lengths and inclinations (a & B). Q2: (20 % Draw the sectional front view of the following figure. (Note: All dimensions are in millimeter). a5 a 20, se 1 of | geQ3: (50%) (Note: All dimensions are in millimeter). Draw the front, top and side view of the following MS- Clamp figure. Page 2 of 2Sst 22 Salahaddin University - Erbil 1" Semester Final Exam Date: 31/1 /2018 Collegeof Engineering 2017-2018, Time 3 hows Petroleum and Chemical Eng. Department Subject Eng. Drawing & Deseripive Geometry Cass: First Year Lecturer Hari A. Sivaily ai-aur ee Fill in the blank with the best answer. prt Kabir prepumepel, 1, The Desspecfis Grojection method does not provide exact size and shape of object 2 Tavaye 0 Mite planes which they are perpendicular to the sight lines. 3.The tus length of otal ns are apes only on _{Z p 4. In cldi'ugine Fthe'tays are parallel to each other, but they are not perpendicular to the plane of projection 5. The intersection of two principal projection planes is called C4 «L- > Q2: (20%) Draw the orthographic projections of the following points: Point A, 20 mm above HP, 25 mm behind VP. Point B, 25 mm below HP, 20 mm behind VP. ie \ Point C, 20 mm below HP, 30 mm in front of VP. An f Point E, on HP, 25 mm behind VP. Point F, on VP, 30 mm below HP. yee 23: 20%) ol , we a i gh £ The foci of an ellipse are 90 mm apart and the major axis is 120 mm long, ‘Draw the ellipse by using four centre method. Q4: (50%) Draw the following view of the stamping tool with original domensions. (Note: All dimensions are in millimeters)Petroleum & Chemical Engineering Dept. Eng. Drawing & Descriptive Geo. Salahaddin University- Erbil | Lecturer: Hardi Siwaily Lecture No.: Fourteen, Sunday, April 8, 2018