How to configure Routing Information Protocol (RIP),

Routing Information Protocol Version 2 (RIPv2) Lab

Practice
omnisecu.com/cisco-certified-network-associate-ccna/how-to-configure-routing-information-protocol-rip.php

If you are not familiar with Routing Information Protocol (RIP), click the following link to
view an introduction to Routing Information Protocol (RIP).

Routing Information Protocol (RIP) Configuration

Routing Information Protocol (RIP) can be configured in a router using the following IOS
commands. The "version 2" IOS command specifies that we are using RIPv2.

Router>enable
Router#configure terminal
Router(config)# router rip
Router(config-router)# version 2
Router(config-router)# network network_id

Routing Information Protocol (RIP) - Lab Practice

The following diagram shows our lab setup. We have three routers, three switches and
three hosts connected as below. The host names, IP addresses and the interfaces of the
routers are shown in diagram. The IP addresses of the hosts are also shown in the
diagram.

1/7
If you are not familiar with a router console connection, click the following link to learn
how to connect the serial port of your computer to router console port.

Click the following link to learn how to connect to the console port of the router if there is
no serial port in your computer.

Click the following links to learn how to use HyperTerminal terminal emulator and
PuTTY terminal emulator to configure router.

Hostname and IP address configuration in Router01

Connect to Router01 console and use the following IOS commands to configure host
name as Router01.

Router>enable
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#hostname Router01
Router01(config)#

Use the following IOS commands to open the fast ethernet interface Fa0/0 configuration
mode on Router01 and configure IP address as 172.16.0.1/16.

Router01>enable
Router01#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router01(config)#interface fa0/0
Router01(config-if)#ip address 172.16.0.1 255.255.0.0
Router01(config-if)#no shutdown

Use the following IOS commands to open the serial interface S0/0 configuration mode on
Router01 and configure IP address as 172.17.0.1/16. You have to set a clock rate also using
the "clock rate" command on S0/0 interface, since this is the DCE side.

Router01>enable
Router01#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router01(config)#interface s0/0
Router01(config-if)#clock rate 64000
Router01(config-if)#ip address 172.17.0.1 255.255.0.0
Router01(config-if)#no shutdown

Do remember to run the "copy running-config startup-config" command from enable

mode, if you want to save the changes you have made in the router.

Hostname and IP address configuration in Router02

Connect to Router02 console and use the following IOS commands to configure host
name as Router02.

2/7
Router>enable
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#hostname Router02
Router02(config)#

Use the following IOS commands to open the fast ethernet interface Fa0/0 configuration
mode on Router02 and configure IP address as 172.18.0.1/16.

Router02>enable
Router02#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router02(config)#interface fa0/0
Router02(config-if)#ip address 172.18.0.1 255.255.0.0
Router02(config-if)#no shutdown

Use the following IOS commands to open the serial interface S0/0 configuration mode on
Router02 and configure IP address as 172.17.0.2/16.

Router02>enable
Router02#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router02(config)#interface s0/0
Router02(config-if)#ip address 172.17.0.2 255.255.0.0
Router02(config-if)#no shutdown

Use the following IOS commands to open the serial interface S0/1 configuration mode on
Router02 and configure IP address as 172.19.0.1/16. You have to set a clock rate also using
the "clock rate" command on S0/1 interface, since this is the DCE side.

Router02>enable
Router02#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router02(config)#interface s0/1
Router02(config-if)#clock rate 64000
Router02(config-if)#ip address 172.19.0.1 255.255.0.0
Router02(config-if)#no shutdown

Do remember to run the "copy running-config startup-config" command from enable

mode, if you want to save the changes you have made in the router.

Hostname and IP address configuration in Router03

Connect to Router03 console and use the following IOS commands to configure host
name as Router03.

Router>enable
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#hostname Router03
Router03(config)#

3/7
Use the following IOS commands to open the fast ethernet interface Fa0/0 configuration
mode on Router03 and configure IP address as 172.20.0.1/16.

Router03>enable
Router03#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router03(config)#interface fa0/0
Router03(config-if)#ip address 172.20.0.1 255.255.0.0
Router03(config-if)#no shutdown

Use the following IOS commands to open the serial interface S0/1 configuration mode on
Router03 and configure IP address as 172.19.0.2/16.

Router03>enable
Router03#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router03(config)#interface s0/1
Router03(config-if)#ip address 172.19.0.2 255.255.0.0
Router03(config-if)#no shutdown

Do remember to run the "copy running-config startup-config" command from enable

mode, if you want to save the changes you have made in the router.

Routing Information Protocol Version 2 (RIPv2) configuration in Router01

Connect to Router01 console and use the following IOS commands to configure Routing
Information Protocol Version 2 (RIPv2) in Router01. Please refer the beginning of this
lesson to view the Routing Information Protocol Version 2 (RIPv2) configuration IOS
commands.

Using the IOS "network" command, as shown below, we specify only the directly
connected networks of this router.

Router01>enable
Router01#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router01(config)#router rip
Router01(config-router)#version 2
Router01(config-router)#network 172.16.0.0
Router01(config-router)#network 172.17.0.0
Router01(config-router)#exit
Router01(config)#exit
Router01#

Do remember to run the "copy running-config startup-config" command from enable

mode, if you want to save the changes you have made in the router.

Routing Information Protocol Version 2 (RIPv2) configuration in Router02

Connect to Router02 console and use the following IOS commands to configure Routing
Information Protocol Version 2 (RIPv2) in Router02. Please refer the beginning of this
lesson to view the Routing Information Protocol Version 2 (RIPv2) configuration IOS
commands.

4/7
Using the IOS "network" command, as shown below, we specify only the directly
connected networks of this router.

Router02>enable
Router02#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router02(config)#router rip
Router02(config-router)#version 2
Router02(config-router)#network 172.17.0.0
Router02(config-router)#network 172.18.0.0
Router02(config-router)#network 172.19.0.0
Router02(config-router)#exit
Router02(config)#exit
Router02#

Do remember to run the "copy running-config startup-config" command from enable

mode, if you want to save the changes you have made in the router.

Routing Information Protocol Version 2 (RIPv2) configuration in Router03

Connect to Router03 console and use the following IOS commands to configure Routing
Information Protocol Version 2 (RIPv2) in Router03. Please refer the beginning of this
lesson to view the Routing Information Protocol Version 2 (RIPv2) configuration IOS
commands.

Using the IOS "network" command, as shown below, we specify only the directly
connected networks of this router, which you want to advertise in your RIP network..

Router03>enable
Router03#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router03(config)#router rip
Router03(config-router)#version 2
Router03(config-router)#network 172.19.0.0
Router03(config-router)#network 172.20.0.0
Router03(config-router)#exit
Router03(config)#exit
Router03#

Do remember to run the "copy running-config startup-config" command from enable

mode, if you want to save the changes you have made in the router.

How to view the routing table in Router01

After the network is converged after the initial configuration and Routing Information
Protocol Version 2 (RIPv2) configuration, we can use the "show ip route" to view the
routing table in Router01, as shown below.

5/7
Router01>enable
Router01#show ip route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
* - candidate default, U - per-user static route, o - ODR
P - periodic downloaded static route
Gateway of last resort is not set
C 172.16.0.0/16 is directly connected, FastEthernet0/0
C 172.17.0.0/16 is directly connected, Serial0/0
R 172.18.0.0/16 [120/1] via 172.17.0.2, 00:00:22, Serial0/0
R 172.19.0.0/16 [120/1] via 172.17.0.2, 00:00:22, Serial0/0
R 172.20.0.0/16 [120/2] via 172.17.0.2, 00:00:22, Serial0/0

The "R" character at the beginning of a line in routing table shows that it is a route
discovered by Routing Information Protocol Version 2 (RIPv2) and "C" character shows
that it is a directly connected network.

How to view the routing table in Router02

When the network is converged after the initial configuration and Routing Information
Protocol Version 2 (RIPv2) configuration, we can use the "show ip route" to view the
routing table in Router02, as shown below.

Router02>enable
Router02#show ip route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
* - candidate default, U - per-user static route, o - ODR
P - periodic downloaded static route
Gateway of last resort is not set
R 172.16.0.0/16 [120/1] via 172.17.0.1, 00:00:07, Serial0/0
C 172.17.0.0/16 is directly connected, Serial0/0
C 172.18.0.0/16 is directly connected, FastEthernet0/0
C 172.19.0.0/16 is directly connected, Serial0/1
R 172.20.0.0/16 [120/1] via 172.19.0.2, 00:00:20, Serial0/1

The "R" character at the beginning of a line in routing table shows that it is a route
discovered by Routing Information Protocol Version 2 (RIPv2) and "C" character shows
that it is a directly connected network.

How to view the routing table in Router03

When the network is converged after the initial configuration and Routing Information
Protocol Version 2 (RIPv2) configuration, we can use the "show ip route" to view the
routing table in Router03, as shown below.

6/7
Router03>enable
Router03#show ip route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
* - candidate default, U - per-user static route, o - ODR
P - periodic downloaded static route
Gateway of last resort is not set
R 172.16.0.0/16 [120/2] via 172.19.0.1, 00:00:02, Serial0/1
R 172.17.0.0/16 [120/1] via 172.19.0.1, 00:00:02, Serial0/1
R 172.18.0.0/16 [120/1] via 172.19.0.1, 00:00:02, Serial0/1
C 172.19.0.0/16 is directly connected, Serial0/1
C 172.20.0.0/16 is directly connected, FastEthernet0/0

The "R" character at the beginning of a line in routing table shows that it is a route
discovered by Routing Information Protocol Version 2 (RIPv2) and "C" character shows
that it is a directly connected network.

Verify the connectivity between networks using the ping command

To verify the Routing Information Protocol Version 2 (RIPv2) routes and the connectivity
between networks, run the ping command from Host01 (IP address: 172.16.0.10/16) to
Host03 (IP address: 172.20.0.10/16).

C:\>ping 172.20.0.10

Pinging 172.20.0.10 with 32 bytes of data:

Reply from 172.20.0.10: bytes=32 time=172ms TTL=125

Reply from 172.20.0.10: bytes=32 time=188ms TTL=125
Reply from 172.20.0.10: bytes=32 time=157ms TTL=125
Reply from 172.20.0.10: bytes=32 time=188ms TTL=125

Ping statistics for 172.20.0.10:

Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
Minimum = 157ms, Maximum = 188ms, Average = 176ms

The ping reply from Host03 (IP address: 172.20.0.10/16) shows that the Routing
Information Protocol Version 2 (RIPv2) is configured well in three routers and there is
network connectivity between different networks.

7/7