Higher and Higher:

The Evolution of the

Buttressed Core
The development of the buttressed core structural system led to a
paradigm shift in tall building design that brought a dramatic
increase in the height of buildings. In the 32 years between the
completion of 1 World Trade Center (1972) and Taipei 101
(2004), there was only a 22 percent increase in the height of the
world’s tallest building. In 2010, the Burj Khalifa claimed the
title at 828 m, eclipsing Taipei 101 by more than 60 percent.
With its innovative buttressed core, the tower represents a major
leap in structural design, elicited by a change in the approach to
the tall building problem through an examination of scale.

By William F. Baker, P.E., S.E., F.ASCE, and

James J. Pawlikowski, S.E., LEED AP, M.ASCE

F IGURE 5
T
HROUGHOUT THE HISTORY of tall for the residential high-rise, the design of Tower Palace III
buildings, structural engineers have in- revealed a new structural solution for the supertall residen-
vented the means to go higher. In the tial tower.
1970s Fazlur R. Khan’s tube concept Tower Palace III was originally designed at more
was a dramatic shift from the tra- than 90 stories, its height supported by a Y-shaped
ditional portal frame system used floor plan. Because its architectural design called for
on such structures as the Empire elevators within the oval floor plate of each wing,
State Building. Later develop- SOM engineers opted to connect the elevators via
ments, including the core plus outrigger system, a central cluster of cores (parts a and b of figure 3).
also provided architects with the tools to design In doing so, the “hub” became the primary lateral
taller, more efficient buildings. However, the re- system of the building. At the two upper me-
sulting growth was gradual, each innovation chanical floors, the perimeter columns also were
marking a point on the progressive scale of the engaged to assist in resisting lateral loads by
tall building. means of virtual outriggers (floor plates above
The buttressed core is a different species. and below in conjunction with a perimeter belt
Permitting a dramatic increase in height, its wall). While not as effective as direct connec-
design employs conventional materi- tions, these virtual outriggers spared the
als and construction techniques and builders the numerous connection
was not precipitated by a change and construction problems typi-
in materials or construc- cally associated with direct
tion technology. The es- outriggers (see figure 4).
sence of the system Throughout the
is a tripod-shaped design process, the
structure in which building exhibit-
a strong central F IGURE 1 ed very good struc-
core anchors three F IGURE 2 tural behavior and
building wings. It performed well in
is an inherently stable the wind tunnel, and it
system in that each wing is became obvious to the engi-
buttressed by the other two. neering team that the struc-
The central core provides the ture could go much higher.
torsional resistance for the However, because of zoning is-
building, while the wings pro- sues, the design of the tower’s
vide the shear resistance and tallest wing was cut from 93
NICK MERRICK ©HEDRICH BLESSING, OPPOSITE; ©SOM, TOP; SOM| ©H.G. ESCH, BOTTOM

increased moment of inertia to 73 stories (the other wings

(see figure 1, typical floor plan were then elevated to compen-
of the Burj Khalifa). The but- sate for the loss of area). De-
tressed core represents a con- spite the decrease in height,
ceptual change in structural the project provided the SOM
design whose evolutionary de- team with the opportunity to
velopment began with Tower explore a new approach to the
Palace III, designed by Chica- tall building problem. Given
go-based Skidmore, Owings Tower Palace III’s efficiency,
& Merrill LLP (SOM). the structural design team in-
Completed in 2004, Tow- ferred that, if a project had a
er Palace III, located in Seoul, sufficiently large parcel, this
South Korea, promoted a new system could be used in build-
standard in high-rise residen- ing at extreme heights.
tial development (see figure In early 2003, soon af-
2). Its tripartite arrangement ter completing the design of
provides 120 degrees between Tower Palace III, SOM was
wings, affording maximum contacted about a potential
views and privacy. Although supertall building in Dubayy
Chicago’s Lake Point Tower (Dubai), part of the Unit-
| SOM

set the architectural precedent ed Arab Emirates. (See “The

0885-7024/12-0010-0058/$30.00 PER ARTICLE OCTOBER 2012 C i v i l E n g i n e e r i n g [59]

 buttressed core is on a 9 m module.
As in Tower Palace III, the walls in
each wing of the Burj Khalifa were
initially spread apart in such
a way as to separate the living
components from the bath and
kitchen components. This provided
four interlocking tubes, but the dimen-
sions were much greater. This plan later
proved problematic because there were nu-
merous doors in the structure and little flexibil-
ity in unit layout. It was thus difficult to comply
with Dubayy code requirements, which dictate accessi-
bility to natural light in the kitchen. As a result, the team
embarked on a series of studies to see if the central core
could resist all of the torsional effects of the building. Follow-
ing a round of parametric studies carried out in the autumn of
2003, it was clear that the central core had enough strength
and stiffness to serve as the building’s torsional hub. Also in
2003, the wing walls were adjusted so that the primary walls
now lined the corridors at the center of each wing, instead of
protruding into the units. Besides improving the efficiency
of the units, this adjustment improved the efficiency of the
entire structure.
F IGURE 3 A
Studies were also carried out to assess the possibility of
eliminating the perimeter columns by using cantilever beams
from the core walls. After SOM was selected to design the Burj
Burj Khalifa Triumphs” by William
F. Baker, P.E., S.E., F.ASCE, Civil
Engineering, March 2010, pages F IGURE 3 B
44–55.) On March 1 of that
year, the team went to New
York to be interviewed for
the project, and it was
agreed there that a brief
idea competition
would be held involv-
ing SOM and various other
invited teams. Given the
success of Tower Palace
III and its potential to be de-
veloped to even greater heights, the
SOM team elected to use this structural
system for what would later become the Burj
Khalifa (see figure 5).
Throughout the design process, SOM engineers
made critical changes to the Tower Palace III design
that were essential to the evolution of the Burj Khalifa’s
buttressed core. The design of the tower’s central core
relied upon close collaboration on the part of SOM ar-
chitects and engineers, and that multidisciplinary ap-
proach successfully fit all of the tower’s elevators and
operating systems within the core while maintaining
good structural behavior. In contrast to the case of Tow-
©SOM, ALL FOUR

er Palace III, Burj Khalifa’s central core houses all ver-

tical transportation with the exception of egress stairs
within each of the wings (see figure 6).
Each of the three wings forming the Burj Khalifa’s

[60] C i v i l E n g i n e e r i n g O C T O B E R 2 0 1 2
F IGURE 4

Khalifa, the engineering team immediately tested the tower’s above sat on the cross-walls of the tier below, yielding great
initial geometry in the wind tunnel, only to discover that it benefits for both tower strength and economy. Engineers also
had large movements and base moments. employed a series of “rules” to simplify load paths and
Upon further analysis, it was discovered that the re- F IGURE 6 construction. These included a rigorous 9 m module
sults were more closely related to the geometry and a philosophy of no transfers (figure 7).
and orientation of the tower than to the struc- Several rounds of high-frequency force bal-
tural system. Therefore, the dynamic proper- ance tests were undertaken in the wind tun-
ties of the structure were manipulated in or- nel as the geometry of the tower evolved
der to minimize the harmonics with the and as the tower was refined architectur-
wind forces. Engineers were able to ac- ally, the setbacks in the three wings fol-
complish this by essentially “tuning” lowing a clockwise pattern (in contrast
the building as if it were a musical to the counterclockwise pattern in
instrument in order to avoid the the original scheme). After each
aerodynamic harmonics that are round of wind tunnel testing,
residual in the wind. the data were analyzed and
A key component of the the building was reshaped
Burj Khalifa’s structural to minimize the wind ef-
design was “managing fects and accommodate
gravity.” This meant unrelated changes in
moving the gravity the client’s program.
loads to where they In general, the num-
would be most use- ber and spacing of the
ful in resisting the lat- setbacks changed, as did
eral loads. Structural en- the shape of the wings.
gineers manipulated the The designers also noticed
tower’s setbacks in such a that the force spectra for cer-
way that the nose of the tier tain wind directions showed

OCTOBER 2012 C i v i l E n g i n e e r i n g [61]

less excitation in the important frequency range
when winds impacted the pointed, or nose, end
of a wing than when they impacted the tails be-
tween the wings.
This was kept in mind when selecting the ori-
entation of the tower relative to the most frequent
directions of strong wind in Dubayy, which are
from the northwest, south, and east. The careful
selection of the tower’s orientation, along with
its variant setbacks, resulted in substantial reduc-
tion of wind forces. By “confusing” the wind, the
design encourages disorganized vortex shedding
over the height of the tower (see figure 8).
In order to have an efficient supertall building,
it is best to use all the vertical elements for both
gravity and wind loads. In order to achieve this
on the Burj Khalifa, it was necessary to engage
all of the perimeter columns of the structure. Be-
cause of the tower’s extreme height, the virtual
outrigger used on Tower Palace III was replaced
by a direct outrigger. In addition to engaging the
perimeter for lateral load resistance, the outrig-
gers allow the columns and walls to redistribute
loads several times throughout the building’s
height. This helps control any differential short-
ening between the columns and the core. By the
time the building meets the ground, the loads in
the walls are somewhat ordinary, and in contrast
to the case of many buildings in which the col- F IGURE 7
umns at the base are massive, most of the Burj
Khalifa’s base columns are relatively thin and
only slightly thicker than those at the top.
The Burj Khalifa’s structural system was cre-
ated with a conscious effort to conform to and
F IGURE 8

The Burj Khalifa’s

structural system was
created with a conscious
effort to conform to and
complement current
construction technology.
©SOM, ALL FOUR

[62] C i v i l E n g i n e e r i n g O C T O B E R 2 0 1 2
 F IGURE 9

However, rather than stepped

setbacks, Las Vegas Tower
has a shape that changes in
elevation, causing the tower’s
width to continually vary.
complement current construction technology. The goal was
to use a highly organized system with conventional elements
that would provide a high repetition of formwork. Initially
the team contemplated a composite floor framing system, as
well as an all-concrete floor framing scheme. It was later de-
cided that the all-concrete scheme was more appropriate and
economical. Although the tower’s floor plate changes as the
structure ascends, the segments near the core repeat them-
selves for as much as 160 levels. As the loads accumulate from
the top down, the sizes of the structural elements are relative-
ly constant since walls were added as the loads accumulated
The design of Las Vegas Tower (Crown Las Vegas) marked
the next step in the evolution of the buttressed core. In early
2006, SOM began working on the design of a 575 m hotel

tower located on the Las Vegas Strip

F IGURE 10 (see figure 9). As in its predecessors,
each of the tower’s three wings but-
tresses the other via a central core.
However, rather than stepped set-
backs, Las Vegas Tower has a shape that
changes in elevation, causing the tow-
er’s width to continually vary. In this
way, wind vortices never get organized.
Furthermore, continual changes in the
tower’s footprint required the loads to
be moved to other elements besides the
wing walls. This was accomplished by
locating the stair at the end of the corri-
dor (see figure 10). The concrete around
the stair, somewhat like the chord of
a truss, acts as a major structural ele-
ment but moves toward the center of
the building as it tapers at the top. In
this way it does not require the stair
transfers that were necessary in the Burj
Khalifa and permits a much smoother
load transfer than a solution that relies

OCTOBER 2012 C i v i l E n g i n e e r i n g [63]

 F IGURE 11

on setbacks. The stair core also provides for a large amount of of the Tower Palace III, Burj Khalifa, and Las Vegas Tower
structure placed near the end of each wing, thereby signifi- paradigm and is derived from an optimized structural form
cantly increasing the tower’s moment of inertia. However, for strength and wind performance (see figure 11). Referred
the system is similar to the Burj Khalifa in that it employs to as the stayed buttressed core, this structural system was de-
direct outriggers connecting the perimeter columns to the veloped from an extensive analysis of the construction history
interior core walls at each mechanical floor. (The project was of its predecessors and of the methods that were employed.
ultimately never built.) SOM proposed two schemes for this tower, one with col-
In 2009 SOM embarked on a design competition for what umns and one without. The scheme with columns is similar
is set to be the next world’s tallest building, Kingdom Tower, to that used for the Burj Khalifa: columns of the perimeter
in Jeddah, Saudi Arabia. At more than 1,000 m, the mixed- blade type located in line with interior transverse core wall
use tower’s elongated, triangular shape is a direct descendant elements. Like their predecessors, these columns required

[64] C i v i l E n g i n e e r i n g O C T O B E R 2 0 1 2
 F IGURE 12

A rigorous study was conducted to determine the optimum wall geometry with
respect to system efficiency and stiffness. Thus, the column-free scheme was born.
linkage to the core via direct outriggers, although distributed ties per square meter as in the Burj Khalifa, which is already
link beams also were considered. Early in the design process, very efficient. This new structural system also eliminates the
it was realized that there was an opportunity to create the need for outriggers and perimeter columns and is easily
next generation of the buttressed core and to elimi- constructed within a standardized formwork system,
nate these columns and, with them, the outriggers, thus greatly simplifying and accelerating construc-
thereby facilitating construction and increasing ef- tion. Tapering as they rise, the symmetrical internal
ficiency. A rigorous study was conducted to deter- core elements are sized to maximize their footprint
mine the optimum wall geometry with respect to and allow the building to move loads efficiently
system efficiency and stiffness (see figure 12). Thus, to the ground while shortening the construction
the column-free scheme was born. Like the system schedule through the elimination of perimeter col-
considered in 2003 for the Burj Khalifa, this system umns, complex outrigger trusses, and similar trans-
used a central structural core with short transverse fer elements.
walls that continue into each of the three wings, The evolution of the buttressed core traces the
supporting cantilevered floors and a column-free development of a simple yet powerful structur-
perimeter (figure 13). Stairs with surrounding al idea. This idea was developed into an appro-
walls are located at the end of each wing and priate and successful system for each of the
scale back a nominal amount at each level buildings described here. With each build-
to establish the building’s taper, there- ing, this system was further refined, re-
by eliminating any setbacks. The flecting both its flexibility and its
tripartite floor geometry, in potential. The buttressed core
combination with a shal- has evolved into a system
© J I L L PA I D E R , B A K E R ’ S P H O T O ; © S O M , A L L R E M A I N I N G

low lease span, pro- that truly incorpo-

duces a breath- rates the ideals of
taking structure structural efficien-
of unencumbered F IGURE 13 cy, constructabil-
space that in its ity, and architec-
height and pan- tural function and
oramic views realizes makes it possible to
the full potential of the buttressed core produce buildings of great height. CE
concept.
Because of the amazing stiffness of William F. Baker, P.E., S.E., F.,ASCE, is
this refined structural system, SOM en- a partner of Skidmore, Owings & Merrill
gineers were able to scale the system LLP in Chicago, and James J. Pawlikow-
to achieve a much taller building us- ski, S.E., LEED AP, M.ASCE, is an associ-
|
SOM

ing virtually the same concrete quanti- Baker Pawlikowski ate director of the firm.

OCTOBER 2012 C i v i l E n g i n e e r i n g [65]