LCD Display G51

User Manual V.2017

1. Exterior Parameters
Casing Material: ABS
Display Material: High Hardness Acrylic (the same hardness value as tempered
glass).

Front View Side View

1
www.czfound.com [email protected]
www.foundmotor.com [email protected]
 Controller Connector Panel Outlet Terminal Wire Connector

Standard
Connector Sequence Table
Sequence No. Wire Colour Functions
1 Red（VCC） Display Power Cord
2 Blue（K） Controller Power Switch Cable
3 Black（GND） Display Ground Wire
4 Green（RX） Display Data Receiving Wire
5 Yellow（TX） Display Data Sending Wire

Extended Functions
Light: Brown (DD): The positive electrode of the light
White (GND): The negative electrode of the light.
The wire colours of the PWM Voltage Motor Power Controller and the
independent speed sensor will be defined otherwise.
Note: Some products are equipped with waterproof connectors, whose internal
wire colors cannot be determined from outside.

3. Functions
a. Display
Speed Display, Motor Power Ratio Display, Battery Level Display,
Error Indication, Total Mileage, Single Mileage, Cruise Control, Brake
Indication, Light Signal
， b. Control and Setting
Power Switch, Front Light Control, 6km/h Cruise Control, Real-time Cruise
Control, Wheel Diameter Setting, 5-Gear Motor Power Setting, Top Speed
Setting, Sleep Interval Setting, Backlight Brightness Setting, Voltage Level
Setting
c. Communications Protocol: UART

Display Readings (display at start for 1 second)

2
www.czfound.com [email protected]
www.foundmotor.com [email protected]
Display Details

3.1 Light

3.2 Battery

3.3 Multi-Function Display

3.4 Vehicle Mode

3.. Speed Display

3
www.czfound.com [email protected]
www.foundmotor.com [email protected]
 Maximum Speed: MAX
Average Speed: AVG
Measuring Unit: MPH or KM/H
The display will calculate the actual travelling speed based on the wheel
diameter and signal data (number of magnet steel is needed for Hall motors).

3.6 Vehicle Status

Digital Voltage

Motor Failure

Throttle Failure

Controller Failure

Brake Indication

Wheel Diameter

3.7 Settings
P00: Restore Factory Settings Set this value to 10 and switch to next setting,
the display items will show all contents and restore original factory settings.
P01: Backlight Brightness (1: darkest; 3: brightest)
P02: Mileage Unit (0: KM; 1: MILE)
P03: Voltage Class 24V / 36V / 48V
P04: Sleep Interval
(0: never, other value means display sleep interval) Unit: minute
P05: Power Assist Gear
0/3 Gear Mode: Gear 1: 2V Gear 2: 3V Gear 3: 4V
1/5 Gear Mode: Gear 1: 2V Gear 2: 2.5V Gear 3: 4V Gear 4: 3.5V Gear 5:
4V
P06: Wheel Diameter Unit: inch Precision: 0.1
P07: Magnet Steel Number (for Speed Test) Range: 1-100
P08: Speed Limit
Range: 0-50km/h, parameter 50 indicates no speed limit.
1. Non-communications status (panel-controlled)
When the current speed exceeds the speed limit, the PWM output will be shut
down; when the current speed falls to lower than the speed limit, the PWM
4
www.czfound.com [email protected]
www.foundmotor.com [email protected]
output will be activated and the driving speed will be set as the current speed ±
1km/h (only applies to assist power speed, not applicable to the handlebar
speed).
2. Communications status (controller-controlled)
The driving speed will be kept constant as the limited value.
Error Value: ±1km/h (applicable to both the assist power/handlebar speed)
Note: The above-mentioned values are measured by metric unit (kilometers).
When the measuring unit is switched to imperial unit (mile), the speed value
displayed on the panel will be automatically switched to corresponding imperial
unit, however the speed limit value in the imperial unit interface won’t change
accordingly.
P09: Direct Start / Kick-to-Start Setting
0: Direct Start
1: Kick-to-Start
P10: Drive Mode Setting
0: Power Assist – The specific gear of the assist drive decides the assist
power value. In this status the handlebar does not work.
1: Electric Drive – The vehicle is driven by the handlebar. In this status the
power gear does not work.
2: Power Assist + Electric Drive – Electric drive does not work in zero-start
status.
P12: Power Assist Intensity Range: 0-5
P13: Power Magnet Steel Number 5 / 8 / 12pcs
P14: Current Limit Value: 12A by default; Range: 1-20A
P15: Unspecified
P16: ODO Zero-Out
Long press the up key for 5 seconds and ODO value will be erased.
P17: (Customer Designated) Auto Cruise Option. 0: No Auto-cruise
1: Auto-Cruise On. Trigger time of auto-cruise is decided by the controller.
P18: (K5S, APT Protocol Bound) Forward / Backward PAS Option.
0: Forward. 1: Backward.
P19: (K5S Protocol Bound) Throttle Level Option.
0: No throttle level. 1: Has throttle levels.
P19: (K5S Protocol Bound) 6km/h Cruise Throttle Definition. 0: Throttle
has no 6km/h cruise definition. 1: Throttle has 6km/h cruise definition.

Note: Due to product upgrade, the product you purchased may be

5
www.czfound.com [email protected]
www.foundmotor.com [email protected]