How to access Diagnostic Mode (pre and post Factory model SR50)

_____________________________________________________________

To access ECU codes on DigiDash model SR50 (2005 to present) go to the Diagnostics
section of the Dash and when prompted, enter the code 45256. From there, you will be
able to read as well as clear out any set code(s).
______________________________________________________________________

To access the ECU codes on the Pre-DigiDash model SR50 (1999 to 2004), turn throttle
to full open while engine is off (“Kill Switch” off). While holding throttle, turn the key
on. Then the CHECK INJECTION light turns on, and after it goes off let go throttle. If
everything was done right you are now in “Diagnostic Mode”

After that, if there are any errors stored in the ECU, the Injection Check Light will start
to blink. Count the number blinks, and then check in the ECU Error Code table (below)
what each set of blinks means (e.g. If it blinks 10 times, then that is ECU Code 10, an
error with the oil pump).

There is approximately a 4 sec delay between each error blink. So you may get 8 flashes,
then a pause, then 3 flashes, then a pause, then 20, etc. After you run the diagnostic error
codes 4 times, it resets or clears the code(s) (it’s taken into consideration that you “fixed”
the error(s)) from the ECU. If there is any other malfunctions after clearing them out, the
injection light will blink again but other error(s) will be reported. Intermittent errors can
appear and re-appear at any time… If there are no blinks, then the ECU has been cleared!

Be warned that it is not uncommon to have a LOT of ECU error(s) if the Diagnostic
Mode hasn’t been access in a long time, especially if the Warning Light has been “on” for
a long time. If that is the case, knowing what “current” error/issue you are dealing with
may be hard to determine.
 ECU Code Action Required
Code Faulty part Possible Cause Action required
ECU 01 Overheated Damaged Thermostat Check Components
engine Damaged Radiator
Damaged Coolant lines

ECU 02 Stator coil Faulty Wiring or connector Check Wiring & Connectors
Pick-up Sensor Check Continuity to ground
Water in/on Pickup Sensor Dry area
Damaged/faulty Stator Check Stator Resistance

ECU 03 TPS TPS pulley screw adjustment Check pulley screw

04 incorrectly
05 Throttle cable incorrectly Check Cable Adjustment
Adjusted
Faulty wiring or connector Check Wiring & Connectors
Damaged TPS Replace TPS in the TBA

ECU 06 TPS Damaged or worn TPS Replace TPS

07

ECU 08 TPS Water in TPS or wiring Dry TPS and/or wiring

ECU 09 ECU Faulty ECU wiring or connector Check Wiring & Connectors
To Terminal pin 15
Inj. Sys relay Faulty wiring to Inj. Sys relay Check Wiring Continuity
Disconnected
Low Bat volts Faulty Rectifier/wiring Check charging sys.
Faulty Stator

ECU 10 Oil Pump Faulty Wiring or connector Check Wiring & Connectors
Faulty connection to ECU pin 2
Damaged Oil Pump Check Resistance in pump
Faulty ECU Check ECU (sect. 11)

ECU11 Air Injector Faulty Wiring or connector Check Wiring & Connectors
Faulty connection to ECU pin 13 and Continuity.
Damaged Air Injector Check Resistance in Air Inj.
Faulty wiring to Inj. Sys relay Check Wiring Continuity
Faulty Fuel Inj. Sys relay Check Relay
Faulty ECU Check ECU (sect. 11)

ECU 12 Fuel Injector Faulty Wiring or connector Check Wiring & Connectors
Faulty connection to ECU pin 3 and Continuity.
Damaged Fuel Injector Check Resistance in Fuel Inj.
Faulty wiring to Inj. Sys relay Check Wiring Continuity
Faulty ECU Check ECU (sect. 11)
ECU 13 Ignition Sys Faulty Wiring or connector Check Wiring & Connectors
Faulty connection to ECU pin 12
Faulty Ignition HT Coil Check HT Coil, lead and cap
Faulty Sparkplug Check & replace if needed
Faulty Fuel Inj. Sys relay Check Relay
Faulty ECU Check ECU (sect. 11)

ECU 14 Fuel Pump Faulty Wiring or connector Check Wiring & Connectors
Faulty connection to ECU pin 14
Faulty Fuel Pump Check Fuel Pump
Faulty ECU Check ECU (sect. 11)

ECU 15 Rev Limiter Max safe engine speed exceeded

ECU 16 ECU Power Faulty Wiring or connector Check Wiring & Connectors
Supply Faulty connection to ECU pin 17
Faulty ECU Check ECU (sect. 11)

ECU 17 High RPM Faulty Throttle Cable Adjustment Check Cable Adjustment
@ Start up Faulty ECU Check ECU (sect. 11)

ECU 18 Temp Sensor Faulty Wiring or connector Check Wiring & Connectors
Faulty connection to ECU pin 9 & 16

ECU 19 Temp Sensor Faulty Temp Sensor Check Temp Resistance (Chap 4)
Faulty ECU Check ECU (sect. 11)

ECU 20 Temp Gauge Faulty Wiring or connector Check Wiring & Connectors
Faulty connection to ECU pin 5
Faulty Sensor/connector See Fault Code 19
Faulty Temp Gauge Check Temp Gauge (chap 4)
Faulty ECU Check ECU (sect. 11)

ECU 21 Inj Sys (Pre-Digi-dash SR50’s)

warning
Light Check Bulb

ECU 22 ECU power Faulty Wiring or connector Check Wiring & Connectors
Supply Faulty connection to ECU pin 17
Faulty ECU Check ECU (sect. 11)

ECU 23 ECU Faulty Atmospheric Sensor Check Wiring & Connectors

Faulty ECU Check ECU (sect. 11)
ECU Codes in Red means that the Engine will not run/start
ECU Coded in Orange means that the Engine may or may not run/start
ECU Code list in file name: ECU Error Code List.xls
ECU Code Action Required file name: ECU Code Action Required.doc
Date last updated: 11-Oct-24
 Error Description Error Code
Engine overheat ECU 01
Pick-up sensor failure ECU 02
Wrong signal from throttle position sensors ECU 03
Wrong signal from throttle position sensor 1 ECU 04
Wrong signal from throttle position sensor 2 ECU 05
Throttle position sensor 1 malfunction ECU 06
Throttle position sensor 2 malfunction ECU 07
Throttle position sensors malfunction ECU 08
Incorrect charging voltage ECU 09
Oil pump malfunction ECU 10
Air injector malfunction ECU 11
Fuel injector malfunction ECU 12
Ignition circuit malfunction ECU 13
Fuel pump malfunction ECU 14
Engine rpm limiter tripped ECU 15
Error in ECU power supply ECU 16
Rpm limiter tripped while starting ECU 17
Engine temperature sensor malfunction ECU 18
Coolant Temperature Sensor ECU 19
Coolant Temperature Gauge ECU 20
Injection System Warning Light (pre Digi-Dash) ECU 21
Error on ECU Throttle sensor connection ECU 22
Atmospheric pressure sensor malfunction ECU 23

Error Codes/Description in red = Engine will NOT

start

Date Last Updated: 11-Oct-24

INSTRUMENT PANEL ERROR DESCRIPTION Error Code

Immobilizer failure: Key code read but not acknowledged DSB 01
Immobilizer failure: Key code not read (key not available or DSB 02
broken transponder)
Immobilizer failure: Broken antenna (open or short-circuited) DSB 03
Immobilizer failure: Inner controller failure DSB 04
Fuel sensor failure DSB 05
Not Specified/used DSB 06
Not Specified/used DSB 07