Scribd Logo
Upload

Welcome to Scribd!

  • 221 views

    Siemens 7SJ86 V7.00 Feeder PTT User Manual ENU

    Uploaded by

    RaúlEmirGutiérrezLópez

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Siemens 7SJ86 V7.00 Feeder PTT User Manual ENU

    Uploaded by

    RaúlEmirGutiérrezLópez
    221 views5 pages

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    221 views5 pages

    Siemens 7SJ86 V7.00 Feeder PTT User Manual ENU

    Uploaded by

    RaúlEmirGutiérrezLópez

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 5

    OMICRON PTL Siemens 7SJ86 V7.

    00 Feeder User Manual ENU

    OMICRON PTL

    Siemens 7SJ86 V7.00 Feeder PTT

    User Manual

    V1.000

    © OMICRON electronics GmbH 1/5


    OMICRON PTL Siemens 7SJ86 V7.00 Feeder User Manual ENU

    Content
    1. General ............................................................................................................................................ 3
    2. Software and Hardware Requirements........................................................................................... 3
    3. Hardware ......................................................................................................................................... 4
    4. Functional Range ............................................................................................................................ 4
    5. XRIO Converter ............................................................................................................................... 5

    © OMICRON electronics GmbH 2/5


    OMICRON PTL Siemens 7SJ86 V7.00 Feeder User Manual ENU

    1. General
    This user manual describes details of testing Siemens 7SJ86 relay with the OMICRON
    Protection Test Template. General information on the usage of OMICRON Protection Testing Library
    items can be found in the OMICRON PTL user manual.

    The template has been tested with the following relay:


    Manufacturer: Siemens
    Model: 7SJ86
    Firmware Version: 7.00

    2. Software and Hardware Requirements


    To use this template, you must have a valid test license for the OMICRON Test Universe 3.00 software or
    higher versions and the following test modules:
     Control Center
     Quick CMC
     Overcurrent
     State Sequencer

    Any CMC test set can be used with this Protection Test Template.

    © OMICRON electronics GmbH 3/5


    OMICRON PTL Siemens 7SJ86 V7.00 Feeder User Manual ENU

    3. Hardware
    There are multiple possibilities of wiring Siemens 7SJ86 relay to a CMC test set. The advised
    connections are shown in Figure 1. These connections are the default settings in the
    Hardware Configuration of the PTT.

    VC
    VN
    VA
    VB
    IN
    IC
    IA
    IB

    Manual Close
    CB aux (52a)
    Start
    Trip
    I0_N*

    I0*

    * is for measured
    current inputs

    Figure 1: Connection for 7SJ86

    4. Functional Range
    Supported functions:
     Overcurrent protection, phases
     Overcurrent protection, ground
     Directional time-overcurrent protection, phases
     Ground-Fault Protection for High-Resistance Ground Faults in Grounded Systems
     Switch On To Fault SOTF protection (with Overcurrent protection)

    Not supported settings or functionalities of the supported functions above:


     Only one inverse time stage is supported for each overcurrent function and at least two definite
    time stages with it.
     Dynamic settings for any overcurrent stage are not supported.
     Directional behavior for 67N is not supported in case the polarization parameter polarization with
    is set to one of the following values:
    o IY (neutral pt.) only
    o zero-sequence Power
     If a residual current transformer is connected to the relay, the setting 3I0 calculated for the
    parameter Measured value of the ground overcurrent function (50N/51N) is not supported.
     Inverse time stages are not supported for the SOTF function.

    Not supported functions:


     Synchrocheck, synchronizing function (25)
     Voltage protection (27), (59)

    © OMICRON electronics GmbH 4/5


    OMICRON PTL Siemens 7SJ86 V7.00 Feeder User Manual ENU

     Power protection active/reactive power


     Thermal overload (49)
     Circuit breaker failure protection (50BF)
     Automatic reclosing (79)
     Frequency protection (81 O/U)
     Fault locator

    Although the functions listed above are not supported by the Protection Test Template, the
    Relay Parameter Section of the XRIO Converter includes all protection parameters of the relay.

    5. XRIO Converter
    The Test Object contains 7SJ86 XRIO Converter, which includes setting parameters of the modeled
    protection relay. The setting parameters are built as an image of the Digsi5 V7.00 software.

    © OMICRON electronics GmbH 5/5

    You might also like