Scribd Logo
Upload

Welcome to Scribd!

  • 56 views

    19-DT-4 Carbon Steel Dove Tail Bar Gratings

    Uploaded by

    Mohamed Elfawal
    The document specifies requirements for 19-DT-4 carbon steel dove tail bar gratings, including descriptions of bearing bars, cross bars, fabrication, design criteria, materials, and accessories. It provides information on references, action submittals, quality assurance, manufacturers, manufactured units, and execution including field verification and installation.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    19-DT-4 Carbon Steel Dove Tail Bar Gratings

    Uploaded by

    Mohamed Elfawal
    56 views3 pages
    The document specifies requirements for 19-DT-4 carbon steel dove tail bar gratings, including descriptions of bearing bars, cross bars, fabrication, design criteria, materials, and accessories. It provides information on references, action submittals, quality assurance, manufacturers, manufactured units, and execution including field verification and installation.

    Original Description:

    Carbon Steel

    Original Title

    19DT4Steel

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document specifies requirements for 19-DT-4 carbon steel dove tail bar gratings, including descriptions of bearing bars, cross bars, fabrication, design criteria, materials, and accessories. It provides information on references, action submittals, quality assurance, manufacturers, manufactured units, and execution including field verification and installation.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    56 views3 pages

    19-DT-4 Carbon Steel Dove Tail Bar Gratings

    Uploaded by

    Mohamed Elfawal
    The document specifies requirements for 19-DT-4 carbon steel dove tail bar gratings, including descriptions of bearing bars, cross bars, fabrication, design criteria, materials, and accessories. It provides information on references, action submittals, quality assurance, manufacturers, manufactured units, and execution including field verification and installation.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 3

    19-DT-4 Carbon Steel Dove Tail Bar Gratings

    Model Specification for type 19-DT-4 Carbon Steel Dove Tail Pressure Lock Gratings as
    Manufactured by Ohio Gratings, Inc.™ 5299 Southway St. SW, Canton, Ohio 44706 or
    approved equal.

    NOTE: The specifier will need to edit this specification to reflect the options in this
    document shown in Red. Some editing can be accomplished by deleting unnecessary
    requirements.
    SECTION 05 53 00
    Metal Fabrications – Metal Gratings

    Part 1: General
    1.1 Section Includes
    A. Prefabricated custom-designed light duty steel bar gratings.

    B. Miscellaneous installation hardware and accessories.

    1.2 References
    A. ASTM A-1011 CS Type B Steel Strip Hot-Rolled Carbon

    B. ANSI/NAAMM- MBG-531-09 Metal Bar Grating Manual.

    C. ANSI-NFSI B101.3-2012 Test Method for Measuring Wet Dynamic Coefficient


    of Friction (Wet DCOF) of Common Hard-Surface Floor Materials

    1.3 Action Submittals


    A. Product Data: The contractor shall submit the manufacturer’s catalog pages
    including load tables, anchor details and standard installation details.

    B. Shop drawings: The contractor shall submit for approval shop drawings for the
    fabrication and erection of all gratings, based on construction drawings of current
    issue. Include plans, elevations, and details of sections and connections as
    required. Show type and location of all fasteners.

    C. Samples of Grating and Anchorage system shall be submitted for approval.

    1.4 Quality Assurance


    A. Manufacturer Qualification: A company specializing in the manufacture of
    metal bar gratings with not less than 10 years of documented experience.

    B. Fabrication tolerances shall be in accordance with applicable provisions and


    recommendations of ANSI/NAAMM 531-09 Metal Bar Grating Manual.

    Part 2: Products
    2.1 Source Requirements:
    Design is based upon use of gratings as manufactured by Ohio Gratings and
    terminology used herein may include reference to the specific performance or
    product of this manufacturer. Such reference shall be construed only as
    establishing the quality of materials, operational features and workmanship to be
    used under this Section and shall not, in any way, be construed as limiting
    competition.

    2.2 Manufacturers:
    Acceptable Manufacturers include Ohio Gratings, 5299 Southway St. SW,
    Canton, Ohio 44706, 800-321-9800 www.ohiogratings.com , or approved equal.

    2.3 Manufactured Units:


    A. Description: Carbon Steel Dove Tail Pressure Lock Grating type 19-DT-4:
    with rectangular bearing bars slotted to receive slotted rectangular crossbars
    assembled in egg-crate fashion and hydraulically pressed to permanently
    lock the bars in place.
    1. Bearing Bar Spacing: 19/16” on center.
    2. Bearing Bar Depth: based on loading requirements and clear
    span.
    3. Bearing Bar Thickness: 3/16” to provide 1” space between bars
    4. Top Surface of Bearing Bars: Plain or serrated or with OnGrip™
    Spray Traction Surface.
    5. Cross Bar Spacing: 4” on center.

    B. Fabrication: Fabricate cutouts in grating sections for penetrations indicated.


    Arrange cutouts to permit grating removal without disturbing items
    penetrating gratings. Band ends and cuts in grating with bars of same size
    and material as bearing bars.

    C. Design Criteria:
    1. Loading: Grating Products shall be designed and manufactured to
    meet the live load conditions of 100 lbs/ Sq Ft with maximum
    deflection of 1/4” for the clear spans shown on the drawings.
    Bearing bar depth shall be as shown on the contract drawings or as
    recommended by the manufacturer to meet the loading
    requirements, clear span conditions and maximum deflections
    specified.

    D. Materials: Bearing bars, cross bars and banding are Carbon Steel Type
    ASTM A-1011 CS Type B.

    E. Fabrication Tolerances shall be in accordance with ANSI/NAAMM MBG


    531-09 Metal Bar Grating Manual.

    F. Finish: Gratings shall be Mill finish or Hot-Dip Galvanized per ASTM


    A123 or Powder Coat Painted (choose color)

    2.4 Accessories:
    Provide appropriate fasteners for type, grade, and class required for the
    approved anchorage system.

    Part 3: Execution
    3.1 Field Verification: Take field measurements prior to preparation of final shop
    drawings and fabrication where required to ensure proper fitting of the work.

    3.2 Installation
    A. Prior to grating installation, contractor shall inspect supports for correct
    alignment and conditions for proper attachment and support of the gratings. Any
    inconsistencies between contract drawings and supporting structure deemed
    detrimental to grating placement shall be reported in writing to the architect or
    owner’s agent prior to placement.

    B. Install grating in accordance with shop drawings and standard installation


    clearances as recommended by ANSI/NAAMM MBG-531-09 Metal Bar Grating
    Manual.

    3.3 Grating Attachment: Use approved attachment system and fasteners to secure
    grating to supporting members as shown on plans.

    You might also like