Scribd Logo
Upload

Welcome to Scribd!

  • 62 views

    Manual-balanceo-De-carga PCC Router Neutro 3 ADSL

    Uploaded by

    Diego Pirela
    This document provides 8 steps to configure load balancing across 3 internet connections of equal speed. It involves naming interfaces, assigning IP addresses, enabling NAT, creating routes, using mangle rules to mark and classify connections, and load balancing new connections across the 3 interfaces using per-connection classification. DNS servers are also configured to resolve public addresses.

    Copyright:

    © All Rights Reserved
    Download as TXT, PDF, TXT or read online from Scribd

    Manual-balanceo-De-carga PCC Router Neutro 3 ADSL

    Uploaded by

    Diego Pirela
    62 views3 pages
    This document provides 8 steps to configure load balancing across 3 internet connections of equal speed. It involves naming interfaces, assigning IP addresses, enabling NAT, creating routes, using mangle rules to mark and classify connections, and load balancing new connections across the 3 interfaces using per-connection classification. DNS servers are also configured to resolve public addresses.

    Copyright

    © © All Rights Reserved

    Available Formats

    TXT, PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document provides 8 steps to configure load balancing across 3 internet connections of equal speed. It involves naming interfaces, assigning IP addresses, enabling NAT, creating routes, using mangle rules to mark and classify connections, and load balancing new connections across the 3 interfaces using per-connection classification. DNS servers are also configured to resolve public addresses.

    Copyright:

    © All Rights Reserved
    Download as TXT, PDF, TXT or read online from Scribd
    Download as txt, pdf, or txt
    62 views3 pages

    Manual-balanceo-De-carga PCC Router Neutro 3 ADSL

    Uploaded by

    Diego Pirela
    This document provides 8 steps to configure load balancing across 3 internet connections of equal speed. It involves naming interfaces, assigning IP addresses, enabling NAT, creating routes, using mangle rules to mark and classify connections, and load balancing new connections across the 3 interfaces using per-connection classification. DNS servers are also configured to resolve public addresses.

    Copyright:

    © All Rights Reserved
    Download as TXT, PDF, TXT or read online from Scribd
    Download as txt, pdf, or txt
    of 3

    Manual de balanceo de carga PCC para 3 Lineas de Internet de la misma Velocidad

    si sigues estos 8 pasos basicos tendra tu balaneco Operando de manera correcta

    PASO 1

    Nombrando las interfaces

    aqui se deben identificar las interfaces que van a usar

    /interface ethernet
    set [ find default-name=ether1 ] comment=Ether1 name=WAN1
    set [ find default-name=ether2 ] comment=Ether2 name=WAN2
    set [ find default-name=ether3 ] comment=Ether3 name=WAN3
    set [ find default-name=ether5 ] comment=Ether5 name=LAN

    Configurando las direeciones IP en cada Interfaz

    PASO 2

    /ip address
    add address=192.168.1.1/24 interface=LAN network=192.168.1.0
    add address=192.168.100.2/24 interface=WAN1 network=192.168.100.0
    add address=192.168.200.2/24 interface=WAN2 network=192.168.200.0
    add address=192.168.250.2/24 interface=WAN3 network=192.168.250.0

    PASO 3

    Enmascarando las interfaces WAN

    /ip firewall nat


    add action=masquerade chain=srcnat out-interface=WAN1
    add action=masquerade chain=srcnat out-interface=WAN2
    add action=masquerade chain=srcnat out-interface=WAN3

    PASO 4

    creando las rutas

    /ip route
    add gateway=192.168.100.1 check-gateway=ping distance=1
    add gateway=192.168.200.1 check-gateway=ping distance=2
    add gateway=192.168.250.1 check-gateway=ping distance=3

    Paso 5

    Vamos a configurar en el mangle las siguientes lineas sirven para marcar las
    conexiones nuevas
    y que lo que entre por una conexion WAN Salga por la misma.
    /ip firewall mangle
    add chain=prerouting in-interface=WAN1 connection-state=new new-connection-
    mark=WAN1_conn action=mark-connection passthrough=yes
    add chain=prerouting in-interface=WAN2 connection-state=new new-connection-
    mark=WAN2_conn action=mark-connection passthrough=yes
    add chain=prerouting in-interface=WAN3 connection-state=new new-connection-
    mark=WAN3_conn action=mark-connection passthrough=yes

    add chain=output connection-mark=WAN1_conn new-routing-mark=to_WAN1 action=mark-


    routing passthrough=yes
    add chain=output connection-mark=WAN2_conn new-routing-mark=to_WAN2 action=mark-
    routing passthrough=yes
    add chain=output connection-mark=WAN3_conn new-routing-mark=to_WAN3 action=mark-
    routing passthrough=yes

    Paso 6

    Ahora dividiremos las conexiones que ingresan por la interfaz nombrada "LAN"
    utilizando el clasificador per-connection-classifier

    /ip firewall mangle


    add chain=prerouting in-interface=LAN connection-state=new dst-address-type=!local
    per-connection-classifier=both-addresses:3/0 action=mark-connection new-connection-
    mark=WAN1_conn passthrough=yes
    add chain=prerouting in-interface=LAN connection-state=new dst-address-type=!local
    per-connection-classifier=both-addresses:3/1 action=mark-connection new-connection-
    mark=WAN2_conn passthrough=yes
    add chain=prerouting in-interface=LAN connection-state=new dst-address-type=!local
    per-connection-classifier=both-addresses:3/2 action=mark-connection new-connection-
    mark=WAN3_conn passthrough=yes

    y tambien marcamos las rutas de las conexiones

    /ip firewall mangle


    add chain=prerouting in-interface=LAN connection-mark=WAN1_conn action=mark-routing
    new-routing-mark=to_WAN1 passthrough=yes
    add chain=prerouting in-interface=LAN connection-mark=WAN2_conn action=mark-routing
    new-routing-mark=to_WAN2 passthrough=yes
    add chain=prerouting in-interface=LAN connection-mark=WAN3_conn action=mark-routing
    new-routing-mark=to_WAN3 passthrough=yes

    Paso 7

    Configurando las rutas, recuerdan las marcas de ruta que hicimos en el paso 5,
    to_WAN1, to_WAN2 y to_WAN3 vamos a usarlas ahora

    /ip route
    add gateway=192.168.100.1 routing-mark=to_WAN1 check-gateway=ping
    add gateway=192.168.200.1 routing-mark=to_WAN2 check-gateway=ping
    add gateway=192.168.250.1 routing-mark=to_WAN3 check-gateway=ping

    Paso 8

    Configurando los DNS Publicos


    /ip dns
    set allow-remote-requests=yes servers=8.8.8.8,8.8.4.4

    You might also like