PT.

TPU PPI Curug Task Card Created: 01 March 2012, 10:24

Page 1 of….. ADF Loop Swing.
A/C Type: Boe 737-800.
RT Number: 47-AWL-07 Prepared by: DoelKamdi
Status: ALI ATA: 34 Originating Task :MPD/AMM
Aircraft: Hours Landings/Cycles Date
Accomplished at:
Applicability:
All Airplanes L/N 1820, 1831, 2517, 2620 and On.
All Airplanes that have incorporated Service Bulletin 737-47-1003.
Interval : 6,500 FH.

AUTOMATIC DIRECTION FINDER SYSTEM - ADJUSTMENT/TEST

1.GENERAL

A. The system test is a full functional check of the ADF system and its interfaces.

TASK 34-57-00-730-802
2. Automatic Direction Finder System - System Test

A. General

(1) Some of the tests need radio reception from local AM commercial broadcast stations or ADF beacon transmitting
stations.

NOTE: ADF bearing checks on the ground, in hangars, or near other airplanes, metal buildings and equipment, etc.
may show inaccurate bearings or weak signals.

2. References Reference

23-51-00-710-801 34-21-00-820-801

34-21-00-820-802

3. Location Zones

Zone Area

Title

Flight Interphone System - Operational Test (P/B 501)

Air Data Inertial Reference System - Alignment from the FMC CDU (P/B 201)
Air Data Inertial Reference System - Alignment from the ISDU (P/B 201)
118 Electrical and Electronics Compartment - Right

211. 211  Flight Compartment - Left

212. 212  Flight Compartment - Right

N INSTRUCTION PERFOME INSPECTION MARK

O D BY BY
1 Prepare for the Test

MLI ALL; AIRPLANES WITH DUAL ADF RECEIVERS SUBTASK 34-

57-00-840-005
(1) Do these steps to prepare for the test:

(a) Make sure the Flight Interphone System is on (TASK 23-51-

00-710-801).

(b) Make sure the Air Data Inertial Reference System is on

(TASK 34-21-00-820-802 or TASK 34-21-00-820-801).

(c) Open this circuit breaker and install safety tag:

F/O Electrical System Panel, P6-1 Row : A ; Col: 17 ;

Number:C01383; Name : RADIO NAVIGATION ADF 2

MLI ALL;
(d) Set the left and right VOR/ADF switches on the RMI to the
ADF position.

MLI ALL; AIRPLANES WITH DUAL ADF RECEIVERS

(e)  Set the CDS switch on the P5 panel to the AUTO

position.

(f)  On the captain's and first officer's EFIS control panels,
set the VOR1/OFF/ADF1 switches to the ADF 1 position.

MLI ALL; AIRPLANES WITH DUAL ADF RECEIVERS

(Continued)

(g) On the captain's and first officer's EFIS control panels, set the
VOR2/OFF/ADF2 switches to the ADF 2 position.

MLI ALL
SUBTASK 34-57-00-860-055
(2) For the audio select panels, do these steps:

(a)  Set the ADF 1 audio selector to the ON position.

NOTE: Make sure that the volume for the ADF 1 system is
 set to a comfortable level.

(b)  Set the volume controls for all other audio selects to the
OFF position.

MLI ALL; AIRPLANES WITH THE V/B/R SWITCH

(c) Set the VOICE/RANGE switch to the BOTH position.

MLI ALL
SUBTASK 34-57-00-860-058
(3) On the ADF control panel, set the switches as follows:

(a)  The ADF 1 mode switch to the ADF position.

(b)  The ADF 2 mode switch to the ADF position.

(c)  The TONE switch to the OFF position.

ADF BITE Test SUBTASK 34-57-00-740-017

2
(1) Do these steps to do a test of the ADF BITE:

(a) On the ADF control panel, push and release the TEST switch
on the ADF 1 mode switch.

1) Make sure the narrow pointer on the RMI slews to 135°

relative to the Heading Lubber Line.

(b) Open this circuit breaker and install safety tag:

CAPT Electrical System Panel, P18-1 Row: A; Col : 4;

Number: C01382; Name : RADIO NAVIGATION ADF 1

(c) Remove the safety tag and close this circuit breaker:

F/O Electrical System Panel, P6-1 Row: A ; Col: 17;

Number: C01383; Name : RADIO NAVIGATION ADF 2

(d) On the ADF control panel, push and release the TEST switch
on the ADF 2 mode switch

1) ) Make sure the wide pointer on the RMI slews to 135°

relative to the Heading Lubber Line.

(e) Remove the safety tag and close this circuit breaker:

CAPT Electrical System Panel, P18-1 Row:A; Col: 4;

Number : C01382;Name RADIO NAVIGATION ADF 1
(F)Open this circuit breaker and install safety tag:

F/O Electrical System Panel, P6-1 Row: A; Col; 17

Number: C01383; Name: RADIO NAVIGATION ADF 2

MLI 001, 002, 005-099, 101-131, 134-141, 143-180, 301; MLI

181-184, 302-999 POST SB 737-31-1650 F. ADF SYSTEM
SELF -TEST

SUBTASK 34-57-00-740-019

(1) To see the ADF test sequence, select VOR or APP on the
EFIS control panel mode selector.

(a)  To start the test, push one of the front panel switches
below the frequency display window on the ADF control
panel.

(b)  To start the test, push the test switch on the ADF control
panel mode selector knob.

(c)  During the first two seconds of the test, the receiver
output goes to a fail condition. The pointer goes out of view
and the amber ADF flag shows momentarily.

(d)  For the next two seconds, the receiver output goes to an
NCD condition. During this time, the amber ADF flag goes
out of view and the pointer stays out of view.

(e)  Next, the test display shows and the pointer goes to a test
position of 135 degrees from the heading lubber line until the
end of test.

NOTE: For a dual system, the test is the same for each ADF
receiver.

MLI ALL; AIRPLANES WITH DUAL ADF RECEIVERS G. ADF-

1 and ADF-2 System Test

MLI ALL
SUBTASK 34-57-00-860-064
(1) Set the ADF 1 frequency control on the ADF control panel to
a local AM broadcast or NDB

station.

MLI ALL; AIRPLANES WITH DUAL ADF RECEIVERS

SUBTASK 34-57-00-750-033
(2) Do these steps to do a check of the ADF-1 system test:
(a) Make sure you hear a loud and clear ADF audio signal at all
audio select locations.

MLI ALL

(b) Make sure the narrow needle on the RMI points to the
selected bearing.

MLI 001, 002, 005-099, 101-131, 134-141, 143-180, 301; MLI

181-184, 302-999 POST SB 737-31-1650; AIRPLANES WITH
THE PFD/ND DISPLAY FORMAT

(c) Make sure the ADF-1 pointers on the captain's and first
officer's ND's show the same bearing.

MLI ALL; AIRPLANES WITH DUAL ADF RECEIVERS

(d) Make sure the ADF bearing accuracy is as follows:

1) +/- 3 degrees at the quadrantal areas (45 degree, 135 degree,

225 degree and 315 degree)

2) +/- 2 degrees at the areas different than quadrantal areas.

MLI 001, 002, 005-099, 101-131, 134-141, 143-180, 301; MLI

181-184, 302-999 POST SB 737-31-1650; AIRPLANES WITH
THE PFD/ND DISPLAY FORMAT

(e) Make sure the ADF L frequencies which show on the bottom
left corner of the captain's and first officer's ND's are the same as
the frequency from the ADF control panel.

MLI ALL; AIRPLANES WITH DUAL ADF RECEIVERS SUBTASK 34-

57-00-860-066
(3) Open this circuit breaker and install safety tag:

CAPT Electrical System Panel, P18-1 Row A Col 4

Number C01382 Name RADIO NAVIGATION ADF 1

MLI ALL

(a) Make sure the narrow needle flag shows on the RMI.

MLI 001, 002, 005-099, 101-131, 134-141, 143-180, 301; MLI

181-184, 302-999 POST SB 737-31-1650; AIRPLANES WITH
THE PFD/ND DISPLAY FORMAT

(b) Make sure the yellow ADF flags show on the captain's and
first officer's ND's.

MLI ALL; AIRPLANES WITH DUAL ADF RECEIVERS SUBTASK 34-

57-00-860-069
(4) Remove the safety tag and close this circuit breaker:

F/O Electrical System Panel, P6-1 Row A Col 17

Number C01383 Name RADIO NAVIGATION ADF 2

SUBTASK 34-57-00-860-070

MLI ALL

(5) For the audio select panels, do these steps:

1. (a)  Set the ADF 2 audio selector to the ON position.

NOTE: Make sure that the volume for the ADF 2 system
is set to a comfortable level.

2. (b)  Set the volume controls for all other audio selects to
the OFF position.

3. (c)  Set the VOICE/RANGE switch to the BOTH

position.

SUBTASK 34-57-00-860-071

(6) Set the ADF 2 frequency control on the ADF control panel to
a local AM broadcast or NDB station.

MLI ALL; AIRPLANES WITH DUAL ADF RECEIVERS SUBTASK 34-

57-00-750-034
(7) Do these steps to do a check of the ADF-2 system:

(a) Make sure you hear a loud and clear ADF audio signal at all
audio select locations.

MLI ALL

(b) Make sure the wide needle on the RMI points to the selected
bearing.

MLI 001, 002, 005-099, 101-131, 134-141, 143-180, 301; MLI

181-184, 302-999 POST SB 737-31-1650; AIRPLANES WITH
THE PFD/ND DISPLAY FORMAT

(c) Make sure the ADF-2 pointers on the captain's and first
officer's ND's show the same bearing.

MLI ALL; AIRPLANES WITH DUAL ADF RECEIVERS

(d) Make sure the ADF bearing accuracy is as follows:

1. 1)  +/- 3 degrees at the quadrantal areas (45 degree, 135

degree, 225 degree and 315 degree)

2. 2)  +/- 2 degrees at the areas different than quadrantal

areas.

MLI 001, 002, 005-099, 101-131, 134-141, 143-180, 301; MLI

181-184, 302-999 POST SB 737-31-1650; AIRPLANES WITH
THE PFD/ND DISPLAY FORMAT

(e) Make sure the ADF R frequencies which show on the bottom
right corner of the captain's and first officer's ND's are the same
as the frequency from the ADF control panel.

MLI ALL; AIRPLANES WITH DUAL ADF RECEIVERS SUBTASK 34-

57-00-860-073
(8) Open this circuit breaker and install safety tag:

F/O Electrical System Panel, P6-1 Row A Col 17

Number C01383 Name RADIO NAVIGATION ADF 2

MLI ALL

(a) Make sure the wide needle flag shows on the RMI.

MLI 001, 002, 005-099, 101-131, 134-141, 143-180, 301; MLI

181-184, 302-999 POST SB 737-31-1650; AIRPLANES WITH
THE PFD/ND DISPLAY FORMAT

(b) Make sure the yellow ADF flags show on the captain's and
first officer's ND's.

MLI ALL; AIRPLANES WITH DUAL ADF RECEIVERS SUBTASK 34-

57-00-860-074
(9) Remove the safety tag and close this circuit breaker:

F/O Electrical System Panel, P6-1 Row A Col 17

Number C01383 Name RADIO NAVIGATION ADF 2

SUBTASK 34-57-00-860-075

(10) Remove the safety tag and close this circuit breaker:

CAPT Electrical System Panel, P18-1 Row A Col 4

Number C01382 Name RADIO NAVIGATION ADF 1
 END OF TASK

Part Installation Details Part Removal Details

Part Number Part
Number
Serial Number Serial
Number
LOG BOOK ENTRY – NGS

AGAR DIBUAT TASK CARD ADF LOOP SWING DENGAN MENGACU KEPADA BAHAN ATAU
MATERI YANG ADA, JUGA DENGAN DOWNLOAD DARI GOOGLE ATAU SUMBER LAIN.

FORMAT TASK CARD BOLEH DIRUBAH UNTUK DISESUAIKAN DENGAN TASK DARI ADF LOOP
SWING.