Catalog 2021

CATALOG AND PARTS BOOK
TABLE OF CONTENTS 

Introduction and Mounting Systems B Series Technical Data  
How to Order or Request a Quote 1 53-54 Common Shapes and Angular A Series Lineup 19-21 Heeled Punches 92
How to Use this Catalog 2-3 55 Orientation 91 A Series Units - 1/4” capacity MS 22-29 How to Order 1
Overview of UniPunch Modular Tooling 4-5 Custom Shapes and Applications 92 AD Unit - 3/4” capacity MS 41 HZ Series Lineup and Units 81, 82
Mounting Method Overview 6-7 57 Forming Tools 93 Adjustable Back Gauge 17,69 Indexing (Keying) 91
AH Series - 1/2” capacity MS 36-40 Keyed Mounting Templates 13
Straight Line Punching Method 8 58 Tonnage Information 94
AHD Series - 1/4” Stainless Steel 43-45 Knock Out Tooling (Electrical) 93
Fast Changeover Method 9 59 Drill Sizes and Bend Allowance
Creating Prototypes Method 10 60 Formulas 95
AJ Series 30-34

AJD Unit - 1/4” Stainless Steel 42
Mounting: The Basic Steps 11 61 Decimal Equivalent Chart 96 Locator Pins 17
Angle Cutoff 2 x 2 x 1/4” capacity 52
Bed Rails and Template Mounting Plate 12 62 Die Clearance Guidlines 97 Maintenance 90
Angular Orientation 91
Unispacers, Keyed Mounting 63 Material Specifications 98

Material Specification Chart 98
Templates, and Ram Plates 13 Metal Guage Data 99 Metal Gauge Chart 99
T-Slotted Plates and Universal Base Plates 14 Holder Slot Sizes and Locations 100-101 B Series Lineup 53, 54 Mounting Methods 6-11
Mounting Accessories 15-18 66 B Series Units - 10 Gauge capacity 55-61 Mounting Screws & Bolts 17
67 Replacement Tooling Bed Rails 5000, 5100 & 5110 12 Multycyl- Air Over Oil System 87
A Series Bend Allowance Chart 95

G Series Unittool Replacement Tooling 102-113 Block Die Units 88
A Series Lineup 19-21  Pick-up Gauges 16

Quick Change Template Mounting 9,12
A-1” 22 68 General Information Channel Punching - AE Unit 72 Radius Corners 99
A-1 1/4” 23 69 Corner Notching - A Series 48 Ram Plates 13
A-1 1/2” 24 70 Glossary 114

Corner Notching - B Series 62,63
A-2” 25 Terms and Conditions 115-116 Corner Radius Tooling 69, 93
A-2 1/2” 26 Index Inside Countersinking 93 Shapes - Common & Additional 91, 92
A-3 1/2” 27 AE Series Back Cover Custom Units 88 Sharpening 89, 90
Shims - Punch & Die 84
A-5 1/2” 28 Cutoff Units - A Series 51
Cutoff Units - B Series 66 Slot Locations 100, 101
29 AE Channel Punching 72
30  Stainless Steel Punching - 1/4” thk 42-45
Stock Size Punches - A Series 86
31 TP Series

Decimal Equivalent Chart 96
32 Die Clearance 97
33 TP Series Lineup 73 Die Sets 88 T Slotted Plate 14
34 TP-1 1/4” 74 Disappearing Pin Stops 16 Tandem Units 88
35 TP-2 3/8” 75  Terms and Conditions 115, 116
36 TP–2” 76 Tonnage Information 94
Edge Notching - A Series 49 Tonnage Reduction - 84, 94
37 Mandrel Tube Punching 77
Edge Notching - B Series 64 Compensator Caps
38 78
Extra Feed Clearance - 1 1/4” 35 TP Series Lineup 73
39 79 Extrusion Punching 5, 69, 72 Tube & Pipe Coping Units 80
40
41
 Tube & Pipe Punching Units 74-79
42 HZ Series Feed Rails 17 

43 FTA Series Feed Thru Units 46, 47 Universal Base Plate 14
Fitted Guides and Stripper Plates 83 Unispacers 7, 10, 13
44 HZ Series Lineup and HZ-3/4” 81
Formed Part Punching 5, 19, 72 Unittool Replacement Tooling and 102-113
45 HZ-1 1/4”, HZ-1 1/2” & HZ-2” 82
Forming Tools 92 Components
Additional Products  Upper Arm Kits 85

48
G Series Lineup 68

83 G Series Mounting 69 Vee Notching - A Series 50
84 G Series Units 70, 71 Vee Notching - B Series 65
51
85 Gauges - Work Stops 15-17 & 69 
86 Gauges - Punch & Die 89
Wrenches 18
Glossary 114
UNIPUNCH
88
LOGO
90
HOLES IN PARTS. FAST.
How to Order or Request a Quote
MINIMUM REQUIRED INFORMATION

Contact UniPunch Sales
Phone: 800-828-7061 / 715-263-3900 ■ Part number or model number
Fax: 800-453-3994 / 715-263-3897 ■ Quantity
E-mail: [email protected] ■ Type and thickness of material being punched
■ For round tooling, specify punch size
■ For standard shaped tooling, specify hole shape,
dimensions and orientation
■ For custom applications, send us a drawing or sketch.
For UniPunch Products, Inc. Terms

and Conditions of Sale, see pages
115 & 116
OPTIONAL FEATURES
Angular Orientation of shaped punches
and dies: Page 91
Heeled Punches: Page 92

Typically used for edge notching.
Chisel Shear on Punches: Page 94

To reduce tonnage requirements.
Back Taper on Punches: Page 99

To help reduce stripping problems.
Stub Tip on Punches: Page 99

Designed to reduce punch tip breakage.
Radius Corners: Page 99

Potentially improves tooling life.
Alternative Tool Steels: Contact UniPunch Copyright © 1998, 2000, 2003, 2006, 2014 UniPunch Products, Inc.
For tough materials that are difficult to punch.
WARNING When UniPunch tooling is used in presses or press
Punch Coating, for example TiN Coating brakes, the point of operation (die space) must be guarded.
(Titanium Nitrite): Contact UniPunch O.S.H.A. requires that the employer must provide point-of-
To increase punch life. operation protection for the press operator. The use of loose
blocks, loose shims or other unsecured material on top of punch
heads or striker plates on UniPunch tooling is strictly prohibited.
Negative Die Taper:
This practice is dangerous and serious operator injury can result.
Potentially reduces slug pulling .
Ph: (800) 828-7061 • (715) 263-3900 • Email: [email protected] • Web: www.unipunch.com

UNIPUNCH HOLES IN PARTS. FAST.
1
H o w To U s e T h i s C a t a l o g — A Ty p i c a l P a g e
This catalog is designed for quick reference and easy UniPunch product specialists can help you solve almost any
accessibility to UniPunch product systems. Most pages are application need. For standard and custom tooling application
standardized to follow the general format shown below. assistance, call 1-800-828-7061 (in the US) or 715-263-3900
SPECIFICATIONS & OPERATING INSTRUCTIONS
AJ-1/ 1"
Specifications OPERATING SHUT HEIGHT: 8-3/8" (212.7mm) MIN. DIE CLEARANCE: .006" ( .15mm)
& operating MIN. SHUT HEIGHT: 8-3/16" (208.0mm) MAX. PUNCH DIAMETER: .4375" (11.11mm)
Series & size
instructions
UNIT OPEN HEIGHT:
DIE HEIGHT:
9-1/8" (231.8mm)
3-1/2" (88.9mm)
MATERIAL FEED CLEARANCE: 7/16" (11.1mm)
MIN. PUNCH DIAMETER:
MAX. SQUARE:
MIN. SHAPE DIMENSION:
.0937" (2.38mm)
.309" (7.85mm)
.0937" (2.38mm)
4
MAX. MATERIAL THICKNESS
(MILD STEEL): 1/4" (6.4mm)
(STAINLESS STEEL): 1/8" (3.18mm)
31.8mm width
ROUND UNITS *SHAPED UNITS COMMON DIMS. KITS AND SHIMS
Model Part Model Part Throat Length Shipping Shaped hole

conversion kit: 7122
No. No. No. No. Depth A Weight
Key kit: 9322 Kits, shims
BASE UNITS 4A J-11⁄4P -LPD 14100P-LPD 4SA J-11⁄4P -LPD 14105P-LPD 4" 7" 9 lbs.
LESS PUNCH, DIE
AND DIE ADAPTER
8A J-11⁄4P -LPD 14101P-LPD 8SA J-11⁄4P -LPD 14106P-LPD 8" 11" 10.5 lbs.
Hardware kit:
Punch shim:
9377
N.A.
& notes.
12A J-11⁄4P -LPD 14102P-LPD 12SA J-11⁄4P -LPD 14107P-LPD 12" 15" 15 lbs.
Model/Part BASE UNITS 4A J-11⁄4A -LPD 14100A-LPD 4SA J-11⁄4A -LPD 14105A-LPD 4" 7" 9.5 lbs.
Pedestal/Adapter
Die shim: 1117-12 See detail at right.
LESS PUNCH & DIE 8A J-11⁄4A -LPD 14101A-LPD 8SA J-11⁄4A -LPD 14106A-LPD 8" 11" 11.0 lbs. 1117-48
No. (Includes Die Adapter) 12A J-11⁄4A -LPD 14102A-LPD 12SA J-11⁄4A -LPD 14107A-LPD 12" 15" 16.5 lbs. 1/16" thk./3 max.
4A J-11⁄4 A 14100A 4SAJ-11⁄4 A 14105A 4" 7" 10 lbs. Upper arm kit: 9733 Round
COMPLETE UNITS 9734 Shaped
WITH DIE ADAPTER 8A J-11⁄4 A 14101A 8SAJ-11⁄4 A 14106A 8" 11" 11.5 lbs.
(Includes Punch & Die) 12A J-11⁄4 A 14102A 12SAJ-11⁄4 A 14107A 12" 15" 16 lbs.
COMPLETE UNITS 4A J-11⁄4 P 14100P 4SA J-11⁄4 P 14105P 4" 7" 10 lbs.
WITH PEDESTAL DIE 8A J-11⁄4 P 14101P 8SA J-11⁄4 P 14106P 8" 11" 11.5 lbs. *To order shaped unit w/ round
punch & die, add suffix "-RPD".
(Includes Punch) 12A J-11⁄4 P 14102P 12SA J-11⁄4 P 14107P 12" 15" 16 lbs.
1" DIA.
LENGTH A
2171 1"
PUNCH HEAD
3/4" 1-7/8"
2113
19.0mm
7/16"DIA.
RETAINER RING
1-1/4" 9/16"
2111
ROUND PUNCH
A SERIES
2110
ROUND PUNCH
THROAT DEPTH RANGE NOTE: FOR SLOT SIZE
WITH HEAD 4-7/8" NEW LENGTH SEE ABOVE & LOCATION SEE
4-11/16" THROW TECHNICAL SECTION
2115 AWAY LENGTH
SHAPED PUNCH
WITH HEAD
1/8" 91130 UNITS SHIPPED WITH

DIA. KEY
B.H.S.C.S. GUIDE RETAINER AS
SHOWN. TO INCREASE
1018 FEED CLEARANCE BY
2140 1-1/4" O.D. GUIDE 1/8", FLIP 1018 GUIDE
RETAINER RETAINER 180 DEGREES
Component STRIPPING
SPRING
2-1/2"
x 5/8" I.D.
AND REASSEMBLE.
expanded view Basic unit

8-3/8"
of unit internal 2180
RETAINER PIN
7/16"I.D.
SHUT
HEIGHT
information
parts, and part 2130
ROUND GUIDE
2-1/16"
numbers 2135
SHAPED GUIDE
3/4" O.D.
NOTE: FOR GUIDE OPTIONS,
REFER TO ADDL. PRODUCTS,
2-3/8"
FITTED STRIPPERS PAGE 83
2170
LIFTER SPRING 1"
1-1/8" O.D. 3-1/2"

DIE
1-3/4"
2120
ROUND DIE 3/4" NEW LENGTH HEIGHT
9/16" THROW AWAY LENGTH
2125
SHAPED DIE 3/4" O.D.
15/16" O.D.
2121 1120 14155
PEDESTAL DIE 3/8" DIA. 1101
15/16" O.D. 3/8" DIA. HOLDER 4" THROAT
14172 PILOT PIN
DIE ADAPTER DIAMOND
1-25/32" 2126 2-1/8" NEW LENGTH
14156
1-1/4" O.D. 15/32" 1-1/2" PILOT PIN HOLDER 8" THROAT
SHAPED 1-15/16 THROW
PEDESTAL DIE AWAY LENGTH 11.9mm 38.1mm
14174 14157
DIE ADAPTER
(SHAPED) HOLDER 12" THROAT
1-1/4" O.D.
UNIPUNCH

31
UNIPUNCHHOLES IN PARTS. FAST.

2
H o w To U s e T h i s C a t a l o g — A Ty p i c a l P a g e ( C o n t i n u e d )
UNIT ORDERING OPTIONS
ROUND UNITS *SHAPED UNITS COMMON DIMS.
Model
No.
Part
No.
Model
No.
Part
No.
Throat Length Shipping
Depth A Weight
The type highlighted in this example represents different
BASE UNITS 4A J-11⁄4P -LPD 14100P-LPD 4SA J-11⁄4P -LPD
14105P-LPD 4" 7" 9 lbs.
options for ordering a punching unit, abbreviated as shown
LESS PUNCH, DIE
AND DIE ADAPTER
8A J-11⁄4P -LPD 14101P-LPD 8SA J-11⁄4P -LPD 14106P-LPD 8" 11" 10.5 lbs. below. (Different units offer different ordering options–the
12A J-11⁄4P -LPD 14102P-LPD 12SA J-11⁄4P -LPD 14107P-LPD 12" 15" 15 lbs.
4A J-11⁄4A -LPD 14100A-LPD 4SA J-11⁄4A -LPD 14105A-LPD 4" 7" 9.5 lbs.
example shown here just happens to have five.)
BASE UNITS
LESS PUNCH & DIE 8A J-11⁄4A -LPD 14101A-LPD 8SA J-11⁄4A -LPD 14106A-LPD
(Includes Die Adapter) 12A J-11⁄4A -LPD 14102A-LPD 12SA J-11⁄4A -LPD 14107A-LPD
8"
12"
11"
15"
11.0 lbs.
16.5 lbs.
LPD Base Unit with Die Adapter (Less Punch and Die)
COMPLETE UNITS
WITH DIE ADAPTER
4A J-11⁄4 A
8A J-11⁄4 A
14100A
14101A
4SAJ-11⁄4 A
8SAJ-11⁄4 A
14105A
14106A
4"
8"
7"
11"
10 lbs.
11.5 lbs.
A Complete Unit with Die Adapter
(Includes Punch & Die) 12A J-11⁄4 A 14102A 12SAJ-11⁄4 A 14107A 12" 15" 16 lbs. (Includes Punch and Die)
WITH PEDESTAL DIE 8A J-11⁄4 P 14101P 8SA J-11⁄4 P 14106P 8" 11" 11.5 lbs. P Complete Unit with Pedestal Die (Includes Punch)
RPD Complete Shaped Unit with Round Punch & Die
*To order shaped unit w/ round punch & die, add suffix "-RPD".
Note: Contact UniPunch Sales for other options
SHAPED HOLE CONVERSION KITS Shaped Die Options

For certain AJ units you have the
To convert a round hole unit into a unit for punching shaped holes, you would select option to purchase either a shaped
Shaped Hole Conversion Kit 7122. This consists of: die adapter and shaped die or the
optional pedestal die. For example,
SHAPED
2135 order the 2125 shaped die and
GUIDE
14174 shaped die adapter or the
optional 2126 shaped pedestal die
in the AJ-11/4 Unit.
KIT PARTS
SHAPED DIE
2125
CONFIGURATION
KEY KIT • 1088-3 GUIDE KEY . . . . . . . . . . . . . .
9322
}
+
• 91312 SOCKET SET SCREW . . . . . .
SHAPED DIE
14174
• 1101 DIAMOND PILOT PIN . . . . . . . . ADAPTER
• 1088-8 ADAPTER DIE KEY . . . . . . . .
• 91310 SOCKET SET SCREW.. . . . . .

OR
• 1019 HOLDER TO ADAPTER KEY . .
SHAPED
2126
• 91332 SOCKET SET SCREW . . . . . PEDESTAL
DIE
HARDWARE KITS
Hardware kits consist of fasteners, retainers, etc. for specific units. For example for the
AJ-1¼ you would order:
KIT PARTS
• 91130 B.H.S.C.S. 1/4 - 20 x 3/4 . . . . . CONFIGURATION
HARDWARE
9377
}
KIT
• 1018 GUIDE RETAINER . . . . . . . . . . .
• 91312 SOCKET SET SCREW #10 - x 1/4
• 91601 1/4" LOCKWASHER . . . . . . . .
PHPh:
: (800)828-7061 • (716)825-7960
(800) 828-7061 • (715) • FAX
263-3900 • Email: : (716) 825-0581
[email protected] • www.unipunch.com
• Web: www.unipunch.com
3
Turn your press brake or punch press into a hole punching profit center.
UniPunch Modular Tooling
✓Works with
existing presses
✓Multiple holes and

notches with one
stroke
✓Short lead time

Start with our tooling.
for ordering
✓Fast changeover
at the press
✓Perfect for
recurring jobs
MOUNTING
✓Low investment
✓Precision
tolerances
held Mount it.
✓Reusable for
different parts
Install it in your press or stand alone system.
Punch it. Profit.
UNIPUNCH
4
Use UniPunch Modular Tooling for multiple holes with each stroke of the press.
The UniPunch System PUNCH, DIE AND PILOT PIN

ARE ALIGNED FOR The C-Frame Unit – Heart of the
■ Dependable tooling for ACCURATE HOLE PUNCHING
Modular Tooling System
{
today’s short run, quick
SELF-CONTAINED
STRIPPING ASSEMBLY
changeover environment
PULLS PUNCH C-FRAME IS PRECISION
OUT OF WORKPIECE MACHINED DUCTILE IRON
■ Combinations of tooling
COMPONENTS ARE
and gauging accessories
are easily set up MADE FROM HIGH
QUALITY TOOL STEEL
GUIDE
■ Punch or notch material
up to ¾” thick
PUNCH
DIE
MOUNTING
PILOT PIN
LOCATES
THE HOLE
CENTER
DIAMOND PILOT PIN FOR SHAPED HOLES
UniPunch Modular Tooling: the solution for a variety of applications
Hole Punching & Notching Flat Parts Aluminum Extrusions Brake Formed / Roll Formed Parts
Angles, Channels & Structural Parts Tube Punching – Round or Square Tubing Other Parts

5
Mounting Methods
Match the method
to your press and
shop requirements
UniPunch provides several methods for mounting modular tooling in your press, press brake or single station system.
The method you select will depend on your shop environment.
Using dedicated setups, the UniPunch system is perfectly aligned with lean manufacturing with fast
changeover at the press for producing small (and/or large) lots quickly each time you need that part.
Straight Line Punching Press Brakes

Only
BED RAIL / STRIP TEMPLATE

UNDER UNIT METHOD
MOUNTING
■ For straight line punching

■ For the edge of sheets, angle iron
and extrusions
Page 8
Fast Changeover from part to part

For Presses & Press Brakes
MOUNTING TEMPLATE METHOD
■ Most popular method for all material thicknesses
■ Makes identical parts consistently
■ Allows units to be mounted outside the press for
faster set up and tooling changeover
■ Keyed, non-keyed and dovetail style templates
are available
Page 9
UNIPUNCH
6
Creating Prototypes Press Brakes
Only
BED RAIL /
UNISPACER METHOD
■ For prototypes or short runs
■ Straight line punching applications
■ Unispacers are easily adjusted to
accommodate varying hole
patterns and part lengths
Page 10
All-Purpose For Presses &

Press Brakes
UniPunch can also provide the following equipment to accommodate your press type and mounting method.
MOUNTING
T-SLOTTED PLATES
in standard widths from 12” to 30”
Page 14
UNIVERSAL BASE PLATES with a uniform

pattern of ½”-13 tapped holes
Page14
CUSTOM BED RAILS AND T-SLOTTED PLATES

manufactured to your specifications
Contact the UniPunch Sales Department
Note: For further information on press mounting and gauging methods,

contact the UniPunch Sales Department or visit our website at www.unipunch.com

UNIPUNCH
7
StraightLinePunching
For Press
In Press Brake
Brakes Mounting
The Strip Template in a Bed Rail is a solution for locating units for punching many holes in a row in flat metal, extrusions and
structural shapes. A Strip Template measures ½” x 4 ½” and is long enough for your part. This fits into the recess in the Bed Rail.
Hole-to-hole accuracy is maintained by the precision machined Strip Template. The pilot pin in the base of each unit assures accurate
positioning of the holes in the part to be punched.
Note: To achieve straight line punching and fast changeover at your press brake,
use a dedicated setup on a keyed template. See page 9
To achieve straight line punching and prototyping, consider using Unispacers. See page 10
BED RAIL / STRIP

TEMPLATE UNDER
UNIT METHOD
■ For straight line punching the edge
MOUNTING
of sheets, angle iron and extrusions.

■ Strip Template, 1⁄ 2" (12.7mm) x 41⁄ 2"
(114.3mm) x specific length, fits
into bed rail recess.
■ The pilot pin in the base of each
unit assures accurate positioning of
holes in the part to be punched.
■ Part print tolerance accuracy
expected is .005” (.13mm).
RAM PLATE
See page 13
HOLE PUNCHING UNITS, GAUGES & BOLTS

See pages 15-17
STRIP TEMPLATE
Contact the UniPunch
Sales Department
5000 OR 5100
BED RAIL
SEE PAGE12
UNIPUNCH
8
Faster Changeover from part to part Presses & Press
Brakes
Dedicated setups are ready when you are. A dedicated setup is a combination of UniPunch press tooling assigned to a specific part,
pre-assembled onto a template and ready for quick installation into a press. The UniPunch tooling is assigned to the part for the life
of the part. If the part is no longer required, the tooling can be disassembled and rededicated in a new setup for a different part.
DEDICATED TEMPLATE
METHOD
■ The most popular method for all
material thicknesses.
■ Make identical parts consistently.
■ Allows units to be mounted outside
the press for fast changeover at the
press.
MOUNTING
RAM PLATE
See page 13
HOLE PUNCHING UNITS, GAUGES & BOLTS

See pages 15-17
PILOT PIN & HOLD DOWN HOLES
Keyed Mounting Template Non-Keyed Mounting Template

Mounting template size determined by parts punched
A dedicated setup on a keyed A dedicated setup on a non-keyed mounting template

mounting template is typically used is typically used in a straight sided press or press
in a press brake. brake with angle supports.
See page 13 Contact the UniPunch Sales Department

9
Creating Prototypes In Press
Brakes
Unispacers fit into the recess in the Bed Rail and permit straight line punching of prototypes in flat metal, extrusions and structural
shapes. If the preliminary hole locations change, Unispacers offer a quick and easy method to relocate the holes… simply reposition
the Unispacers on the Bed Rail. For a staggered line of holes, use the slotted side of the Unispacer.
BED RAIL /
UNISPACER METHOD
■ For prototype or short run straight
line punching applications with
varying part lengths.
■ Quick and easy set up and
relocation of holes makes this a
preferred mounting method.
■ Unispacer fits into Bed Rail recess.
■ Unispacer has two .376" diameter
MOUNTING
holes on one side to accept unit

pilot pins and .376" slot on
opposite side for unit front to
back adjustment.
RAM
RAMPLATE
PLATE
See page 13
HOLE PUNCHING UNITS,

GAUGES & BOLTS
HOLE PUNCHING UNITS,
See pages
GAGES 15-17
& BOLTS
SHUT HEIGHT
A = 8-3¼8"
B = 5-1¼2"
UNISPACERS
SEE PAGE 13
5000 OR 5100
BED RAIL
SEE PAGE 12

10
Mounting: The Basic Steps
It’s easy to start using UniPunch tooling. This overview demonstrates using the
UniPunch modular system in a dedicated setup. Here’s how...
1 2
Start by sending us a drawing or sample part. Based on your requirements, UniPunch will recommend
appropriate tooling and gauging.
3 4
MOUNTING
Once an order is placed, UniPunch will provide a layout With your approval, UniPunch will manufacture the mounting
drawing for your approval. template to precisely locate the holes according to your specifications.
5 6
UniPunch will ship the appropriate tooling along with When you receive the tooling you will assemble the
the template. units on the template using the provided layout drawing.
7 8 9
Depending on the application, material can be You can punch and notch multiple holes The tooling in the dedicated setup is
hand fed (as shown) or fed off a coil. with each stroke of the press. assigned to the part for the life of the part.
Here it is shown stored on a shelf, ready for the
next time that part is required.
If the part is no longer required, the modular tooling can be disassembled

and remounted on a new template for a different part.
11
BH eo dw Rt ao i losr daenrd Te m p l a t e M o u n t i n g P l a t e
Bed Rails – Versatile means of mounting UniPunch modular A & B Series tooling and gauges on press brakes
■ Mainly used for straight 5000 5100
9-1/2"
line punching within a
47⁄ 8" (123.8mm) area 9-1/2" 1"
4.878
1⁄ 2"
4.878 1"
front to back.
1⁄ 2" 2-3/16"
1⁄ 2"
■ Two styles available – 2-7/16"
7/8"
1-1/2" 2-1/2"
5000 & 5100 in lengths
up to 12'. 1" 2"
■ A Strip Template or 23/32"

23/32"
Unispacer fits into 1⁄ 2"
1⁄ 2"
recess area to support
tooling. Units are
positioned with pilot pins
located in reamed holes BED RAIL NO. 5000 BED RAIL NO. 5100
and then bolted to T- Part No. Length Weight Part No. Length Weight
slots at rear of Bed Rail.
5000-24 24” 70 lbs. 5100-24 24” 124 lbs.
■ Style 5100 is available
with a 1⁄ 2" (12.7mm) key 5000-48 48” 140 lbs. 5100-48 48" 248 lbs.
slot in template recess 5000-72 72” 210 lbs. 5100-72 72" 372 lbs.
area to accept a press
brake bending die, 5000-96 96” 280 lbs. 5100-96 96" 496 lbs.
allowing parts to be 5000-120 120” 350 lbs. 5100-120 120" 620 lbs.
MOUNTING
punched and brake-

5000-144 144” 420 lbs. 5100-144 144" 744 lbs.
formed in same setup.
Bed Rails, G-Series – for mounting UniPunch modular single & triple spring G-Series tooling and end gauge on press.
The UniPunch 5110 Bed Rail BED RAIL NO. 5110 5110
is designed with one T-slot
Part No. Length Weight
and a top mounted key that
accurately positions the 5110-48 48” 92 lbs.
G-Series fixed base units 5110-72 72” 138 lbs.
for straight line punching or 5110-96 96” 184 lbs.
the G-Series adjustable
5110-120 120” 230 lbs.
base units for staggered
5110-144 144” 276 lbs.
hole patterns.

12
U n i s p a c e r s , K e y e d M o u n t i n g Te m p l a t e s a n d R a m P l a t e s
Unispacers
■ Unispacers fit into the UNISPACERS
recess in the 5000 &
5100 Bed Rails for Part No. For Use With Units
punching holes in
prototype parts. The 5060 Up to 1” wide
second hole in the 5061 1 ¼” to 2” wide
Unispacer aligns units for
5062 2 ¼” to 3” wide
shaped hole punching.
■ For staggered hole 5067 3 ½” wide
patterns, Unispacers are 5069 4” wide
turned over and unit pilot
pins are inserted in the
slot. 5064 5 x 5 Notching Units
Keyed Mounting Templates – Used to support and position UniPunch modular tooling and gauges within a press brake.
■ Typically made from ¾”
(19mm) HRS. CRS or
Aluminum are made RAM PLATE
Keyed Mounting
upon request. Other Templates are supplied with
MOUNTING
template thicknesses are press brake key in bottom.
available upon request.
■ Drilled and reamed holes
are in precise locations
of the part to be
punched.
■ For pricing of all
templates, contact the
UniPunch Sales KEYED MOUNTING TEMPLATE
Department.
Ram Plates – Provide additional ram area for staggered hole patterns.
5019 SERIES RAM PLATES 5019 SERIES RAM PLATES
Part No. Length Weight
5019-24 24" 33 lbs.

5019-48 48" 66 lbs.
5019-72 72" 96 lbs.
5019-96 96" 128 lbs.
5019-120 120" 160 lbs.
5019-144 144" 192 lbs.
For custom designed Ram Plates, contact the UniPunch Sales Department.

UNIPUNCH
13
T-
H oSwl o t ot e odr dP el ar t e s a n d U n i v e r s a l B a s e P l a t e s
T-Slotted Plates – Used to mount modular tooling and gauges in punch presses or stamping presses.
PP SERIES T-SLOTTED PLATES ■ Can be used in press
brakes with angle
Part No. Weight support brackets.
9/16"
1" 2" 1/2" T-BOLT SLOTS A 1⁄ 2" (12.7mm) mounting
PP-1248 220 key is available upon
PP-1272 330 request.
1-7/8"
PP-12108 495 ■ Standard widths from
WIDTH PP-12120 550
12" (304.8mm) to 30"
(762mm).
PP-12144 660
.
PP-1848 320
First two digits of part number indicate the width PP-1872 480
and the last two (or three) digits indicate the
length. PP-18108 719
T-Slotted Plates, other than sizes shown, are PP-18120 799
available upon request. Contact the UniPunch PP-18144 959
Sales Department.
PP-2436 321
PP-2448 428
PP-2472 642
MOUNTING
PP-24108 962
PP-24120 1069
PP-24144 1284
PP-3036 405
PP-3048 540
PP-3072 810
PP-30108 1215
PP-30120 1350
PP-30144 1620
Universal Base Plates – Made of 3⁄ 4" (19.05mm) thick steel plate and completely covered with uniform pattern of 1⁄ 2"-13 tapped holes
for bolting units in position.
3/4" 1-1/4" 1"

UB SERIES UNIVERSAL BASE PLATES ■ Light weight for easier
handling and storage.
Part No. Part No. ■ Ideal for short runs of
1"
UB-1224 UB-1872 small and medium sized
A
parts.
UB-1236 UB-2424
■ Standard widths from
UB-1248 UB-2436
12" (304.8mm) to 30"
UB-1260 UB-2448 (762mm).
5/8"
B UB-1272 UB-2460
UB-1824 UB-2472
First two digits of part number indicate the width
“A” and the last two or three digits indicate the UB-1836 UB-3036
length “B”. Special sizes made to order. UB-1848 UB-3048
Special order Universal Base Plates can be
UB-1860 UB-3060
made from aluminum tooling plate.
Universal Base Plates, other than sizes shown,
are available upon request. For pricing, contact
the UniPunch Sales Department.

14
MH oowu nttoi nogr dA ec rc e s s o r i e s
UniPunch offers a variety of mounting accessories, gauges (stops), part supports (feed rails), wrenches and
hold down bolts to provide fast and easy assembly of modular tooling. The mounting accessories you will
require depends on the mounting method you select and the type of part being punched.
Typical 3-pin gauging Template Mounting Complete Setup with Accessories
MOUNTING
UNIVERSAL STOPS MAGNETIC STOPS
For template, T-slotted plate and Bed
Description Part No. Rail mounting setups, these
For use with template or T-Slotted Description Part No. Magnetic Stops insure accurate
Universal Stop 5050 Plate mounting setups with either ‘A’ gauging of all work pieces. The part
or ‘B’ Series Units. Magnetic Stop 5088 is magnetically held, eliminating the
(11⁄ 4" Wide) A built in screw adjustment for necessity for the operator to hold
Magnet Only 5083
variations in stock dimensions may the part against the stop.
Universal Stop 5054
be used by removing gauge pin and
(1" Wide) gauging against screw.
1-1/4" 2-1/2"
1/2" DIA.
1-3/4"
1-1/8"
1-3/4"
4"
8"
8-5/8"
CLOSE EDGE STOPS CLOSE EDGE STOPS (DISC)
Part. No. Close Edge Stops allow units to be Description Part. No.
set closer together and still have Disc Gauge allows work piece to be
5084 Complete Ass’y 5099 gauged inside a holder close to die.
room for gauges.
Disc Only 5103 Disc can be adjusted to ‘A’ or ‘B’
Series die heights.

15
Mounting Accessories
This economical stop is designed
DOWEL PIN STOPS 1" for use with ‘A’ or ‘B’ Series
3/8" units on template mounting.
Description Part No. 3/4"
A & B Series 5055 1/2" DIA.
1-3/4"
2"
Adjustable Stop has an

ADJUSTABLE STOPS adjustment screw for quick
compensation of various
Description Part No. work piece sizes.
A Series 5092
B Series 5052
1/2" DIA.
3/4" 3-1/2"
These End Stops are adjustable

ADJUSTABLE END STOPS AND front-to-back in three positions
SPACER ASSEMBLY on Unispacer.
MOUNTING
Description Part No.

A Series 5135
B Series 5125 8-3/8"
1-3/4"
Disappearing Pin Stops are

DISAPPEARING PIN STOPS spring loaded and are used
1/2" DIA. 1-1/4" for edge and end gauging in
Description Part No. progressive operations.
1-3/4"
A Series 5048
B Series 5044
8"
PICKUP GAUGES — Specify hole size

FIXED (11/4" WIDTH ) A SERIES B SERIES when ordering
1-1/4" gauges. UniPunch
Description Part No. Part No. stationary Pickup
1-3/4"
gauges are used to
Gauge for 1⁄ 2" Dia. & Under 5056-1 5058-1 engage previously
Replacement Tip for Above 5057-1 5059-1 punched holes.
8" Designed specially
Gauge for Over 1⁄ 2" Dia. 5056-2 5058-2 for pass-along
1/2" DIA. multiple hit
Replacement Tip for Above 5057-2 5059-2 operations.
PICKUP GAUGES — Specify hole size

SPRG. LD. (11/4" WIDTH ) A SERIES B SERIES when ordering
1-1/4" gauges. This
Description Part No. Part No. UniPunch gauge is
1-3/4"
used in operations
Gauge for 1⁄ 2" Dia. & Under 5046-1 5042-1 requiring retractable
Replacement Tip for Above 5047-1 5043-1 pickup pins, such as
8" multiple hit setups.
Gauge for Over 1⁄ 2" Dia. 5046-2 5042-2
1/2" DIA.
Replacement Tip for Above 5047-2 5043-2

16
Feed Rails are adjustable in
FEED RAILS height for use with both ‘A’ and
15"
‘B’ Series units for unobstructed
Description Part No. sliding of part into position. The
Magnetic Feed Rails are simply
Non-Magnetic 5038 placed on mounting plates
10" eliminating hold down bolts.
Magnetic 5039
For use on 5000 and 5100

* ADJUSTABLE BACK STOPS series bed rails to back gauge
and support part.
Description Part. No. 30"
A Series Adj. 5120

B Series Adj. 5130
* Back Stop & Unispacer Assemblies.
ADJUSTABLE BACK GAUGES The Adjustable Back Gauge is used to

accurately position parts. Most holders
Part No. can be drilled for back gauge by
customer or at factory for an additional
MOUNTING
1220 charge. This 7⁄ 16” hole is located
3 11⁄ 16” from base on ‘A’ Units and
2 9⁄ 16” on ‘B’ Units.
For locating units in

LOCATOR PINS position with actual part
on T-Slotted Plate or
For Use With Units Part No. Bed Rail.
A-1, A-11⁄ 4, AJ-1, AJ-11⁄ 4 1055
A-11⁄ 2, AJ-11⁄ 2 1056
A-2, AJ-2 1057
B-1, B-11⁄ 4 1050
B-13⁄ 4 1051
BX-21⁄ 4 1052
G-3⁄ 4, BX-3⁄ 4 1064
NUT, BOLT AND WASHER SETS

Part No. Dia. Length Used With
5010 1⁄ 2" 31⁄ 4" Quick-Lock B-BX-A-AJ 4"
1⁄ 2" 3-1/4" 3-1/4" 3-1/8"
5035 31⁄ 4" Sq. Head Bolt B-BX-A-AJ 1/2" 1/2" 1/2" 5/16"
1"
5/16"
5010 5035 5113 5151 5143

5113 1⁄ 2" 4" Sq. Head Bolt — AH
FOR A & B UNITS FOR AH UNITS FOR FOR
BX-3/4 UNITS G UNITS
5151 5⁄ 16" 31⁄ 8" BX-3⁄ 4
5143 5⁄ 16" 1" G
TEMPLATE MOUNTING SCREWS AND WASHER

Part No. Dia. Length Used With
5141-12 1⁄ 2" 21⁄ 4" B-BX-A-AJ 2-1/4" 3"
5012-12 — — Washer Only 1/2" 1/2"
5104-12 1⁄ 2" 3" AH
5141 5104
FOR A & B UNITS FOR AH UNITS
5150-12 5⁄ 16" 21⁄ 4" BX-3⁄ 4"
5003-12 — — Washer Only
All bolts are specially designed for mounting UniPunch units and accessories to Templates, T-Slotted Plates and Bed Rails.

17
*1⁄ 2-13 * For 1⁄2-13 S.H.C.S.

Hex T Wrench
Designed for efficiency,
the special loop handle
Part No. on the wrench makes the
1193 hex key easier to use.
MOUNTING
This Hex wrench

UNIKEY WRENCHES includes most of
the standard hex
Part No. sizes required for
UniPunch unit
1070 screws and bolts.
TEMPLATE LAYOUT DESIGN INFORMATION

UniPunch can provide CAD files of units for use in creating templates. The formats that
are available are DXF (2D footprint), DWG (2D footprint) and STEP (3D model).
Contact the UniPunch Sales Department at [email protected]

18
A Series Lineup
A, AJ, AJD, AH, AHD, OA, AD, FCU, A-Notching and A-Shearing
• 8-3/8” shut height & 3-1/2” die height
• Material Thickness: Up to 3/4”
• Part Feed Clearance from 7/16” to 1-1/4”
A Units (Pages 22 - 29)

The “A” punching units are the workhorses of the UniPunch product line. Available “A” holder widths
are: 1”, 1 ¼”, 1 ½”, 2”, 2 ½”, 3”, 3 ½”, 5 ½” and 8”. Holder width is important because it defines the
minimum hole to hole distance. The “A” Series are widely used in industry to punch mild steel up to
1/4" thickness. Depending on your material thickness, punch diameters are available up to 5.000”
(127mm).
AJ Units (Pages 30 - 34)

“AJ” punching units are ideal for punching angles and channels, aluminum extrusions and other formed
parts. Available “AJ” holder widths are: 1”, 1 ¼”, 1 ½”, 2” and 2 ½”. Holder width is important
because it defines the minimum hole to hole distance. The “AJ” units are widely used in industry to
punch mild steel up to 1/4" thickness. Depending on your material thickness, punch diameters are
available up to 1.500” (38.10mm).
The “AJ” Unit assembled with Pedestal Die uses a one piece pedestal die for punching close to a leg
of angles, channels and extrusions. Pedestal dies are routinely modified to accommodate formed parts.
A SERIES
The “AJ” Unit assembled with Die Adapter is a two piece design; the die adapter accepts a button die.
One benefit of using the “AJ” Unit with a die adapter is the ability to change button die sizes for
multiple materials, at a lower cost.
Two common types of altered pedestal dies are shown below; others are available.
Submit a drawing of your part to the UniPunch Sales Department for a tooling
recommendation.
A
1288 Altered Ped Die - Flats
C
E Required parameters
A = Front Flat Location E = Chamfer
B D
B = Front Flat Height
E
Specify Dia. or Shape
C = Rear Flat Location
E°
TDC -Total Die Clearance
D = Rear Flat Height
A 1289 Altered Ped Die - Boss

E Required parameters
Pedestal Dies are an alternative to die adapters. They
B E A = Top Diameter Specify Dia. or Shape
can be modified to allow punching holes in oddly
E° B = Front/Top Height TDC -Total Die Clearance
shaped angles, channels, and extrusions as illustrated E = Chamfer - 45° unless
above. otherwise requested
Feed Clearance Units “FCU” (Page 35)

“FCU” punching units feature extra wide feed openings that allow you to "front feed" parts such as
channels, angles and extrusions. Available holder widths are: 1 ¼”, 1 ½” and 2 ¼”. These units are
used to punch mild steel up to 1/8" thickness. Depending on your material thickness, punch diameters
are available up to .8750” (22.22mm). (For thicker material punching applications, see the “AJ” Series.)

19
A Series Lineup
AH Units (Pages 36 - 39)

“AH” punching units are in the UniPunch product line to offer tooling that can punch 1 ½” round holes
in mild steel up to 1/2" thick. For thinner material, punch diameters are available up to 3.000”
(76.20mm). Available “AH” holder widths are: 2 ½”, 3”, 3 ½” and 6”.
OA Unit (Page 40)

The “OA” unit is an oversized AH-6 unit providing additional hole diameter capacity. It offers the
capability of punching up to a 4.000” diameter hole in 3/16” mild steel.
AD Unit (Page 41)

The “AD” unit is in the UniPunch product line to offer the capability of punching holes in up to 3/4"
thick mild steel. It features two sets of 24 disc springs in order to strip the punch from such thick
material. The “AD” unit is a 4” wide holder. Depending on your material thickness, punch diameters are
A SERIES
available up to 1.125” (28.57mm).
AJD (Formerly part of the D Series) (Page 42)

Standard “AJ” units are limited to punching up to 1/8” thick stainless steel. “AJD” units are UniPunch
standard 2” wide “AJ” units assembled with premium D2 tool steel punches for reduced wear when
punching up to ½” diameter holes in stainless steel up to 1/4" thick.
AHD Units (Formerly part of the D Series) (Pages 43 - 45)

“AH” units are limited to punching up to 5/32” thick stainless steel. “AHD” units are UniPunch
standard “AH” units assembled with premium D2 tool steel punches for reduced wear when punching
up to 1 ½” diameter holes in stainless steel up to 1/4" thick. Available “AHD” holder widths are: 2 ½”,
3” and 3 ½”.
UNIPUNCH
20
A Series Lineup
A Series Notching Units (Pages 48 & 51)

These units are designed to operate as stand-alone tools or can be used in conjunction with the
UniPunch “A” Series Lineup to punch and notch parts up to 1/4” (6.4mm) thick mild steel in the same
press setup.
Corner Notching Units (Page 48)

UniPunch “A” Series Corner Notch Units are self-contained dies available in 90 degree left hand or
right hand units. Two models are offered for corner notch sizes of up to 3” x 3” or 5” x 5”.
Die clearance is pre-set at the factory for notching up to ¼” (6.4mm) mild steel. Replacement punch
and die blades, springs and other components are available from stock. Units for custom corner
configurations are available.
A SERIES
A Series Flat Stock Cutoff Unit (Page 51)
UniPunch “A” Series 6300 Flat Stock Cutoff Units are self-contained two post die shearing units
available in widths up to 8” (203.2mm). These units can be mounted in a press or press brake in
conjunction with other “A” Series tooling, or can be used for stand-alone cut-to-length applications in mild
steel up to 1∕4" (6.4 mm) thickness. Other widths can be manufactured to your requirements.

21
A-1 " OPERATING SHUT HEIGHT: 8-3/8" (212.7mm) MAX. PUNCH DIAMETER:
MIN. SHUT HEIGHT: 8-3/16" (208.0mm) .3125" (7.93mm) in 1/4" (6.4mm) M.S.
.4375" (11.11mm) in 1/8" (3.18mm) M.S.
UNIT OPEN HEIGHT: 9-1/8" (231.8mm)
MIN. PUNCH DIAMETER: .0937" (2.38mm)
DIE HEIGHT: 3-1/2" (88.9mm)
MAX. SQUARE: .309" (7.85mm)
25.4mm width MIN. DIE CLEARANCE:
MAX. MAT. THK. (M.S.):
.006" ( .15mm)
1/4" (6.4mm)
MAX. MAT. THK. (S.S.):
.0937" (2.38mm)
3/32" (2.4mm)
KITS AND SHIMS ROUND UNITS *SHAPED UNITS COMMON DIMS.

Shaped hole Model Part Model Part Throat Length Shipping
conversion kit: 7111 No. No. No. No. Depth A Weight
Key kit: 9300 4A-1-LPD 2003-LPD 4SA-1-LPD 2005-LPD 4" 7" 8 lbs.
Hardware kit: 9393 BASE UNITS 8A-1-LPD 2000-LPD 8SA-1-LPD 2006-LPD
LESS PUNCH & DIE 8" 11" 10 lbs.
Punch shim: N.A. 12A-1-LPD 2001-LPD 12SA-1-LPD 2007-LPD 12" 15" 13.5 lbs.
Die shim: 1091-12 pk. 4A-1 2003 4SA-1 2005 4" 7" 8.5 lbs.
1091-48 pk. COMPLETE UNITS
8A-1 2000 8SA-1 2006 8" 11" 10.5 lbs.
1/16" thk./2 max. (Includes Punch & Die)
12A-1 2001 12SA-1 2007 12" 15" 14 lbs.
Upper arm kit: 9731 Round
9732 Shaped *To order a shaped unit with round punch & die, add the suffix “- RPD”
15/16" DIA.
2075 LENGTH A
PUNCH HEAD 5/16"
5/8" 1-7/8"
7/16"DIA. 15.9mm
2113
RETAINER RING
1" 9/16"
2111
ROUND PUNCH
2011 & LOCATION SEE
ROUND PUNCH SEE ABOVE TECHNICAL SECTION
WITH HEAD
4-7/8" NEW LENGTH
2016 4-11/16" THROW
AWAY LENGTH
A SERIES
SHAPED PUNCH
WITH HEAD 91130 UNITS SHIPPED WITH
1/8" SHOWN. TO INCREASE
DIA. KEY 1018 FEED CLEARANCE, FLIP
GUIDE 1018 GUIDE RETAINER
RETAINER 180 DEGREES AND
REASSEMBLE.
2045 1" O.D.

STRIPPING x 1/2" I.D.
SPRING
8-3/8"
2-1/2" SHUT
HEIGHT
2180
RETAINER PIN
7/16"I.D.
2-3/8"
2030 NOTE: FOR GUIDE OPTIONS,
ROUND GUIDE REFER TO ADDL. PRODUCTS,
2035 2-1/16" FITTED STRIPPERS PAGE 83

SHAPED GUIDE
3 / 4 " O. D . 3-1/2"
DIE
HEIGHT 1-3/4"
2070
LIFTER SPRING 1-1/16"
1001 1101
1" O.D. 3/8" DIA. 3/8" DIA. 2055
PILOT PIN DIAMOND SHAPED HOLDER 4" THROAT
2120
ROUND DIE 3/4" NEW LENGTH PILOT PIN
2056
9/16" THROW AWAY 19/32" 1-1/2" SHAPED HOLDER 8" THROAT
2125 LENGTH 15.1mm 38.1mm
SHAPED DIE
2057
3 / 4 " O. D .
SHAPED HOLDER 12" THROAT

22
OPERATING SHUT HEIGHT: 8-3/8" (212.7mm)

MIN. SHUT HEIGHT:
UNIT OPEN HEIGHT:
DIE HEIGHT:

(MILD STEEL):
8-3/16" (208.0mm)
9-1/8" (231.8mm)
3-1/2" (88.9mm)
1/4" (6.4mm)
MIN. DIE CLEARANCE:
MAX. PUNCH DIAMETER:
MAX. SQUARE:
(STAINLESS STEEL):
.006" ( .15mm)
.4375" (11.11mm)
.0937" (2.38mm)
.309" (7.85mm)
.0937" (2.38mm)
3/32" (2.4mm)
A-1/
31.8mm width
1"
4

No. No. No. No. Depth A Weight conversion kit: 7112
4A-1 ⁄4-LPD
1
2103-LPD 4SA-1 ⁄4-LPD
1
2105-LPD Key kit: 9300
4" 7" 11.5 lbs.
BASE UNITS 8A-11⁄4-LPD 2100-LPD 8SA-11⁄4-LPD 2106-LPD Hardware kit: 9394
LESS PUNCH & DIE 8" 11" 13 lbs.
12A-11⁄4-LPD 2101-LPD 12SA-11⁄4-LPD 2107-LPD 12" 15" 15.5 lbs. Punch shim: N.A.
4A-1 ⁄41
2103 4SA-1 ⁄4
1
2105 4" 7" 12 lbs. Die shim: 1091-12 pk.
COMPLETE UNITS 1091- 48 pk.
8A-11⁄4 2100 8SA-11⁄4 2106 8" 11" 13.5 lbs.
(Includes Punch & Die) 1/16" thk./3 max.
12A-11⁄4 2101 12SA-11⁄4 2107 12" 15" 16 lbs.
*To order a shaped unit with round punch & die, add the suffix “- RPD” 9734 Shaped
1" DIA. LENGTH A
5/8" 1-7/8"
2171 1" 15.9mm
PUNCH HEAD
2113 7/16"DIA. 1-1/4" 9/16"

RETAINER RING
2111 THROAT DEPTH RANGE NOTE: FOR SLOT SIZE

ROUND PUNCH SEE ABOVE & LOCATION SEE
TECHNICAL SECTION
2110
ROUND PUNCH
WITH HEAD
4-7/8" NEW LENGTH
4-11/16" THROW
A SERIES
2115 91130 UNITS SHIPPED WITH
SHAPED PUNCH AWAY LENGTH B.H.S.C.S. GUIDE RETAINER AS
WITH HEAD SHOWN. TO INCREASE
1018 FEED CLEARANCE, FLIP
1/8" GUIDE 1018 GUIDE RETAINER
DIA. KEY RETAINER 180 DEGREES AND
REASSEMBLE.
2140 1-1/4" O.D.

STRIPPING x 5/8" I.D. 8-3/8"
SPRING SHUT
2-1/2" HEIGHT
2180 91010
RETAINER PIN S.H.C.S.
7/16"I.D. 2-3/8"
(2 REQ’D)
2130
ROUND GUIDE
2175
2135 2-1/16" DIE BLOCK
SHAPED GUIDE 3-1/2"
3 / 4 " O. D . DIE
HEIGHT 1-3/4"
2170
LIFTER SPRING 1" 2155
1001 1101
3/8" DIA. 3/8" DIA. SHAPED HOLDER
1-1/8" O.D. PILOT PIN DIAMOND 4" THROAT
1/2" 1-1/2" PILOT PIN
12.7mm 38.1mm 2156
2120
ROUND DIE SHAPED HOLDER
3/4" NEW LENGTH 8" THROAT
2125 2157
SHAPED DIE
3 / 4 " O. D . SHAPED HOLDER
12" THROAT

23
A-1/
38.1mm width
1"
2
MIN. SHUT HEIGHT:
UNIT OPEN HEIGHT:
DIE HEIGHT:

(MILD STEEL):
8-3/16" (208.0mm)
9-1/8" (231.8mm)
3-1/2" (88.9mm)
1/4" (6.4mm)
MIN. DIE CLEARANCE:
MAX. SQUARE:
(STAINLESS STEEL):
.006" ( .15mm)
.6250" (15.87mm)
.1250" (3.18mm)
.441" (11.20mm)
.0937" (2.38mm)
3/32" (2.4mm)

Key kit: 9300 4A-11⁄2-LPD 2203-LPD 4SA-11⁄2-LPD 2205-LPD 4" 7" 13.5 lbs.
Hardware kit: 9394 BASE UNITS 8A-11⁄2-LPD 2200-LPD 8SA-11⁄2-LPD 2206-LPD 8" 11" 16.5 lbs.
LESS PUNCH & DIE 12A-11⁄2-LPD 2201-LPD 12SA-11⁄2-LPD 2207-LPD 12" 15" 19.5 lbs.
Punch shim: N.A. .
Die shim: 1092-12 pk. 4A-11⁄2 2203 4" 7" 14 lbs.
1092-48 pk. 4SA-11⁄2 2205
COMPLETE UNITS 8A-11⁄2 2200 8SA-11⁄2 2206 8" 11" 17 lbs.
1/16" thk./3 max. (Includes Punch & Die) 12A-11⁄2 2201 12" 15" 20 lbs.
12SA-11⁄2 2207
9736 Shaped
*To order a shaped unit with round punch & die, add the suffix “- RPD”
1-1/4" DIA.
LENGTH A
3/4" 1-7/8"
2271
PUNCH HEAD
1" 19.0mm
5/8"DIA. 1-1/2"
2213 9/16"
RETAINER RING
2211
ROUND PUNCH
SEE ABOVE & LOCATION SEE
2210 TECHNICAL SECTION
ROUND PUNCH
WITH HEAD
4-7/8" NEW LENGTH
A SERIES
2215 4-11/16" THROW 91130 UNITS SHIPPED WITH

REASSEMBLE.
2240 1-1/2" O.D.

STRIPPING x 3/4" I.D. 8-3/8"
SPRING SHUT
HEIGHT
2-1/2"
91010
2180
RETAINER
S.H.C.S.
5/8"I.D. (2 REQ’D) 2-3/8"
PIN
2230
ROUND GUIDE
2-1/16" 2275
2235
DIE BLOCK 3-1/2"
SHAPED DIE
GUIDE HEIGHT 1-3/4"
1" O.D.
2270
LIFTER 1" 1001 1101 2255
SPRING 3/8" DIA. 3/8" DIA. SHAPED HOLDER 4" THROAT
PILOT PIN DIAMOND
1-7/16" O.D. PILOT PIN 2256
2220 9/16" 1-1/2"
ROUND DIE 3/4" NEW LENGTH 14.3mm 38.1mm 2257
9/16" THROW AWAY LENGTH SHAPED HOLDER 12" THROAT
2225
SHAPED DIE 1" O.D. 2258

24

MIN. SHUT HEIGHT:
UNIT OPEN HEIGHT:
DIE HEIGHT:

(MILD STEEL):
8-3/16" (208.0mm)
9-1/8" (231.8mm)
3-1/2" (88.9mm)
1/4" (6.4mm)
MIN. DIE CLEARANCE:
MAX. SQUARE:
(STAINLESS STEEL):
.006" ( .15mm)
.8750" (22.22mm)
.1875" (4.76mm)
.618" (15.69mm)
.1250" (3.18mm)
3/32" (2.4mm)
A-2
50.8mm width
"

4A-2-LPD 2303-LPD 4SA-2-LPD 2305-LPD 4" 7" 18.5 lbs. Key kit: 9300
BASE UNITS 8A-2-LPD 2300-LPD 8SA-2-LPD 2306-LPD 8" 11" 22.5 lbs. Hardware kit: 9395
LESS PUNCH & DIE 12A-2-LPD 2301-LPD 12SA-2-LPD 2307-LPD 12" 15" 27.5 lbs.
Punch shim: N.A.
4A-2 2303 4" 7" 19 lbs. Die shim: 1093-12 pk.
4SA-2 2305 1093-48 pk.
COMPLETE UNITS 8A-2 2300 8SA-2 2306 8" 11" 23 lbs.
(Includes Punch & Die) 12A-2 2301 12" 15" 28 lbs. 1/16" thk./3 max.
12SA-2 2307
. Upper arm kit: 9737 Round
9738 Shaped
1-1/2" DIA. LENGTH A
1" 1-7/8"
25.4mm
2371 1"
PUNCH HEAD
2313 7/8"DIA.
RETAINER RING 2" 9/16"
2311
ROUND PUNCH THROAT DEPTH RANGE NOTE: FOR SLOT SIZE
ROUND PUNCH
WITH HEAD
4-7/8" NEW LENGTH
A SERIES
2315 4-11/16" THROW 91130 UNITS SHIPPED WITH
REASSEMBLE.
2340 2" O.D.

STRIPPING x 1" I.D. 8-3/8"
SPRING SHUT
HEIGHT
2-1/2"
91011
2180 S.H.C.S.
RETAINER (2 REQ’D) 2-3/8"
7/8"I.D.
PIN
2330
ROUND GUIDE
2-1/16" 2375 3-1/2"
2335 DIE BLOCK DIE
SHAPED HEIGHT
GUIDE 1-1/4" O.D. 1-3/4"

REFER TO ADDL. PRODUCTS, 2355
1001
2370 FITTED STRIPPERS PAGE 83
3/8" DIA.
1101/ SHAPED HOLDER 4" THROAT
LIFTER 1" 3/8" DIA.
PILOT PIN 3/4" 1-1/2" DIAMOND
SPRING 38.1mm
2356
19.0mm PILOT PIN SHAPED HOLDER 8" THROAT
1-11/16" O.D.
2320-1 2357
2320-2 1-1/2" DIA. DIE SIZES OVER .749" SHAPED HOLDER 12" THROAT
ROUND DIE 3/4" NEW LENGTH 2358
9/16" THROW AWAY 2325-1
SHAPED DIE SHAPED HOLDER 18" THROAT
2325-2 LENGTH
SHAPED DIE SIZES OVER .749"
1 - 1/4" O.D. 1 - 1/4" O.D.

25
A-2 /
63.5mm width
1"
2
MIN. SHUT HEIGHT:
UNIT OPEN HEIGHT:
DIE HEIGHT:

(MILD STEEL):
8-3/16" (208.0mm)
9-1/8" (231.8mm)
3-1/2" (88.9mm)
1/4" (6.4mm)
MIN. DIE CLEARANCE:
MAX. SQUARE:
(STAINLESS STEEL):
.006" ( .15mm)
1.5000" (38.10mm)
.2812" (7.15mm)
1.060" (26.92mm)
.1250" (3.18mm)
3/32" (2.4mm)

Key kit: 9300 4A-21⁄2-LPD 2400-LPD 4SA-21⁄2-LPD 2405-LPD 4" 7" 27.5 lbs.
Hardware kit: 9396 BASE UNITS 8A-21⁄2-LPD 2401-LPD 8SA-21⁄2-LPD 2406-LPD 8" 11" 33.5 lbs.
LESS PUNCH & DIE
Punch shim: 1109-12 pk. 12A-21⁄2-LPD 2402-LPD 12SA-21⁄2-LPD 2407-LPD 12" 15" 43.5 lbs.
1109-48 pk.
1/16" thk./3 max 4A-21⁄2 2400 4SA-21⁄2 2405 4" 7" 28 lbs.
COMPLETE UNITS 8A-21⁄2 2401 8SA-21⁄2 2406 8" 11" 34.5 lbs.
Upper arm kit: 9739 Round (Includes Punch & Die)
12A-21⁄2 2402 12SA-21⁄2 2407 12" 15" 44.5 lbs.
9740 Shaped
LENGTH A
1-3/8" 1-7/8"
2485
PUNCH
34.9mm
SCREW 3-1/4"
F.H.S.C.S.
1-1/2" DIA.
2-1/2" 9/16"
2484
PUNCH
DRIVER 2-15/32"
A SERIES

2440-10 TECHNICAL SECTION
STRIPPING
SPRING
SET OF 10
STACK AS 91130 UNITS SHIPPED WITH
SHOWN B.H.S.C.S. GUIDE RETAINER AS
SHOWN. TO INCREASE
2-1/2" DIA. 1018 FEED CLEARANCE, FLIP
2442 GUIDE 1018 GUIDE RETAINER
SPRING RETAINER 180 DEGREES AND
GUARD 1-3/4" REASSEMBLE.
2433
RETAINER
RING
2-11/16" 8-3/8"
SHUT
HEIGHT
2435 2-1/8" O.D.
GUIDE x 1-1/ 2" I.D.
2470 91013
LIFTER 2"
SPRING S.H.C.S.
(2 REQ’D) 2-3/8"
2-7/16" DIA.
1/4"
DIA. KEY 2475 3-1/2"
2-13/32" NEW LENGTH DIE BLOCK
2-7/32" THROW AWAY LENGTH DIE
2411
HEIGHT 1-3/4"
ROUND PUNCH
1-1/2" DIA.
2416
SHAPED PUNCH
2420
ROUND DIE 1001 1101 2455
3/4" NEW LENGTH 3/8" DIA. 3/8" DIA. SHAPED HOLDER 4" THROAT
9/16" THROW AWAY LENGTH PILOT PIN DIAMOND
2425
SHAPED DIE 2-1/8" DIA. 1-3/8" 1-1/2" PILOT PIN 2456
34.9mm 38.1mm SHAPED HOLDER 8" THROAT
2457

26

MIN. SHUT HEIGHT:
UNIT OPEN HEIGHT:
DIE HEIGHT:

(MILD STEEL):
8-3/16" (208.0mm)
9-1/4" (235mm)
3-1/2" (88.9mm)
1/4" (6.4mm)
MIN. DIE CLEARANCE:
MAX. SQUARE:
(STAINLESS STEEL):
.012" ( .30mm)
2.0000" (50.80mm)
.5000" (12.70mm)
1.414" (35.92mm)
.1250" (3.18mm)
3/32" (2.4mm)
A-3 /
88.9mm width
1"
2
Model Part Model Part Throat Length Shipping All A-31⁄ 2 units furnished
No. No. No. No. Depth A Weight with Shaped Driver and Guide
8A -31⁄ 2-LPD Key kit: 9301

2900-LPD 8SA -31⁄ 2-LPD 2905-LPD 8" 113⁄ 4" 44 lbs.
BASE UNITS 12A -31⁄ 2-LPD Hardware kit: 9354
LESS PUNCH & DIE
2901-LPD 12SA -31⁄ 2-LPD 2906-LPD 12" 153⁄ 4" 54 lbs.
Punch shim: 1109-12 pk.
1109-48 pk.
8A -31⁄ 2 2900 8SA -31⁄ 2 2905 8" 113⁄ 4" 45.5 lbs. 1/16" thk./3 max.
COMPLETE UNITS
(Includes Punch & Die) 12A -31⁄ 2 2901 12SA -31⁄ 2 2906 12" 153⁄ 4" 55.5 lbs.
.
LENGTH A
91072
S.H.C.S. 2-3/8"
NYLOK 60.3mm 2-7/8"
2-1/2"
TOP HEAD
SOLD IN
2984 DRIVER
ASS’Y ONLY
3-1/2" 9/16"
2940-7
STRIPPING
A SERIES
SPRING
SET OF 7
STACK AS
SHOWN THROAT DEPTH RANGE NOTE: FOR SLOT SIZE
TECHNICAL SECTION
2942
SPRING 1-19/32"
GUARD 91420
STRIPPER BOLT
3-7/8" DIA.
2935
SHAPED
GUIDE
2-1/2" 2-11/16"
2846
LIFTER
SPRING 8-3/8"
(2 REQ’D) 1/ 2" O.D. SHUT
2-3/4" O.D.
HEIGHT
BOTTOM NOTE: FOR GUIDE OPTIONS,

DRIVER REFER TO ADDL. PRODUCTS,
SOLD IN 2984
ASS’Y ONLY 2-1/2"
2511 1-1/2" DIA. 3-1/2"

ROUND PUNCH
DIE
2515 2-13/32" NEW HEIGHT 1-3/4"
SHAPED LENGTH
PUNCH 2-7/32" THROW
AWAY LENGTH
1/4" DIA. KEY 1001 1101 2955
3/8" DIA. 3/8" DIA. SHAPED HOLDER 8" THROAT
PILOT PIN DIAMOND 2956
2520 3/4" NEW LENGTH PILOT PIN SHAPED HOLDER 12" THROAT
ROUND DIE 5/8" THROW AWAY LENGTH 2-3/8" 1-1/2"
60.3mm 38.1mm 2957
2525 3-1/2" DIA. SHAPED HOLDER 18" THROAT
SHAPED DIE

27
A-5 /
139.7mm width
1"
2
MIN. SHUT HEIGHT:
UNIT OPEN HEIGHT:
DIE HEIGHT:

(MILD STEEL):
8-3/16" (208.0mm)
9-1/4" (235 mm)
3-1/2" (88.9mm)
1/4" (6.4mm)
MIN. DIE CLEARANCE:
MAX. SQUARE:
(STAINLESS STEEL):
.012" ( .30 mm)
3.0000" (76.20mm)
1.0000" (25.40mm)
2.121" (53.87mm)
.1875" (4.76mm)
3/32" (2.4mm)

AllA-51⁄ 2
units furnished Model Part Model Part Throat Length Shipping
with Shaped Driver and Guide No. No. No. No. Depth A Weight
Key kit: 9302 8A -51⁄ 2-LPD 2830-LPD 8SA -51⁄ 2-LPD 2835-LPD
BASE UNITS 81⁄ 4" 121⁄ 4" 82 lbs.
Hardware kit: 9354 LESS PUNCH & DIE 12A -51⁄ 2-LPD 2831-LPD 12SA -51⁄ 2-LPD 2836-LPD 121⁄ 4" 161⁄ 4" 94 lbs.
1109-48 pk. COMPLETE UNITS 8A -51⁄ 2 2830 8SA -51⁄ 2 2835 81⁄ 4" 121⁄ 4" 84 lbs.
1/16" thk./3 max. (Includes Punch & Die) 12A -51⁄ 2 2831 12SA -51⁄ 2 2836 121⁄ 4" 161⁄ 4" 96 lbs.
LENGTH A
91072
S.H.C.S. 3" 3-1/2"
NYLOK 76.2mm
2-1/2"
91012
S.H.C.S.
(3 REQ’D)
TOP DRIVER
HEAD SOLD IN
2844 ASS’Y ONLY
5-1/2" 9/16"
2843-4
STRIPPING
SPRING
SET OF 4
A SERIES
STACK AS
SHOWN
2849 1-3/8"
SPRING THROAT DEPTH RANGE NOTE: FOR SLOT SIZE
GUARD SEE ABOVE & LOCATION SEE
5-3/8" DIA. TECHNICAL SECTION
2845
SHAPED 91420
GUIDE 3-1/8" STRIPPER BOLT
2-1/2"
2846
LIFTER
SPRING
(4 REQ’D)
1/ 2" O.D. 4" O.D.
8-3/8"
SHUT
HEIGHT
BOTTOM PUNCH FITTED STRIPPERS PAGE 83
DRIVER SOLD IN
2844 ASS’Y ONLY
2-1/2"
1/4" DIA. KEY 1-1/2" DIA. 3-1/2"

DIE
2512
2-13/32" NEW LENGTH HEIGHT 1-3/4"
ROUND PUNCH
2-7/32" THROW AWAY
2516 LENGTH
SHAPED 1101
1001
PUNCH 3/8" DIA. 3/8" DIA.
PILOT PIN DIAMOND 2865
PILOT PIN SHAPED HOLDER 8" THROAT
3820 27/32" NEW LENGTH 3" 1-1/2"
ROUND DIE 21/32" THROW AWAY 76.2mm 38.1mm 2866
LENGTH SHAPED HOLDER 12" THROAT
3825 4-15/16" DIA.
SHAPED DIE

28

MIN. SHUT HEIGHT:
UNIT OPEN HEIGHT:
DIE HEIGHT:
8-3/16" (208.0mm)
9" (228.6mm)
3-1/2" ( 88.9mm)
MIN. DIE CLEARANCE:
.012" ( 50.8mm)
1/4" (6.4mm)
5.000" (127.00mm) in 10 GA./.134" (3.40mm) M.S.
4.500" (114.30mm) in 3/16" (4.76mm) M.S.
3.500" (88.90mm) in 1/4" (6.4mm) M.S.
MAX. SQUARE:
2.000" (50.80mm)
3.535" (89.79mm)
.250" (6.35mm)
3/32" (2.4mm)
A-8
203.2mm width
"
KITS AND SHIMS

Model Part Model Part Throat Length Shipping All A-8 units furnished
No. No. No. No. Depth A Weight with Shaped Driver and Guide
Key kit: 9338
BASE UNITS 12A-8-LPD 1401-LPD 12SA-8-LPD 1406-LPD 121⁄ 2" 171⁄ 2" 212 lbs.
LESS PUNCH & DIE
Hardware kit: 9399
Punch shim: N.A.
COMPLETE UNITS Die shim: N.A.
(Includes Punch & Die)
12A-8 1401 12SA-8 1406 121⁄ 2" 171⁄ 2" 216 lbs.
91130
B.H.S.C.S. 91130
(2 REQ’D) B.H.S.C.S.
2878 1018
HOLDER & GUIDE KEY GUIDE RETAINER
(2 REQ’D) (2 REQ’D)
4-3/8" LENGTH A
111.1mm 4-1/2"
91072
S.H.C.S.
(NYLOK) 91047
S.H.C.S.
(4 REQ’D)
1473
A SERIES
PUNCH PLATE
8" 9/16"
2240 6043
STRIPPING SPRING CAGE
SPRING (4 REQ’D)
(9 REQ’D)
1470
LIFTER SPRING
(4 REQ’D)

SHAPED
STRIPPING GUIDE

8-3/8"
SHUT
HEIGHT
1474 2"
PUNCH DRIVER
3-1/2"
DIE 2-1/2"
1-1/2" DIA. HEIGHT
2-7/16" NEW LENGTH 1001 1101

1410 3/8" DIA. PILOT PIN 3/8" DIA. DIAMOND
ROUND PUNCH PILOT PIN
4" 1-1/2"
1415 101.6mm 38.1mm
SHAPED PUNCH 1456
SHAPED HOLDER 12-1/2" THROAT
1420
ROUND DIE 3/16" NEW LENGTH
1425 6-1/2" DIA.

SHAPED DIE

29
AJ-1 " OPERATING SHUT HEIGHT: 8-3/8" (212.7mm) MAX. PUNCH DIAMETER:
MIN. SHUT HEIGHT: 8-3/16" (208.0mm) .3125" (7.94mm) in 1/4" (6.4mm) M.S.
.4375" (11.11mm) in 1/8" (3.18mm) S.S.
MAX. SQUARE: .309" (7.85mm)

.006" ( .15mm)
1/4" (6.4mm)
.0937" (2.38mm)
1/8" (3.18mm)

Key kit: 9322
BASE UNITS 4A J-1P-LPD 14000P-LPD 4SA J-1P-LPD 14005P-LPD 4" 7" 7.5 lbs.
Hardware kit: 9377 LESS PUNCH, DIE 8A J-1P-LPD 14001P-LPD 8SA J-1P -LPD 14006P-LPD 8" 11" 9.5 lbs.
Punch shim: N.A. AND DIE ADAPTER
12A J-1P-LPD 14002P-LPD 12SA J-1P -LPD 14007P-LPD 12" 15" 13 lbs.
Upper arm kit: 9731 Round BASE UNITS 4A J-1A-LPD 14000A-LPD 4SA J-1A-LPD 14005A-LPD 4" 7" 8.0 lbs.
LESS PUNCH & DIE 8A J-1A-LPD 14001A-LPD 8SA J-1A-LPD 14006A-LPD 8" 11" 10.0 lbs.
9732 Shaped (Includes Die Adapter) 12A J-1A-LPD 14002A-LPD 12SA J-1A-LPD 14007A-LPD 12" 15" 13.5 lbs.
COMPLETE UNITS 4A J-1 A 14000A 4SAJ-1 A 14005A 4" 7" 8.5 lbs.
WITH DIE ADAPTER 8A J-1 A 14001A 8SAJ-1 A 14006A 8" 11" 10.5 lbs.
(Includes Punch & Die) 12A J-1 A 14002A 12SAJ-1 A 14007A 12" 15" 14 lbs.
COMPLETE UNITS 4A J-1 P 14000P 4SA J-1 P 14005P 4" 7" 8.5 lbs.
*To order shaped unit w/ round WITH PEDESTAL DIE 8A J-1 P 14001P 8SA J-1 P 14006P 8" 11" 10.5 lbs.
(Includes Punch) 12A J-1 P 14002P 12SA J-1 P 14007P 12" 15" 14 lbs.
15/16" DIA. LENGTH A

2075
PUNCH HEAD 5/16" 3/4" 1-7/8"
19.0mm
2113
RETAINER RING 7/16"DIA.
1" 9/16"
2111
ROUND PUNCH
2011 THROAT DEPTH RANGE NOTE: FOR SLOT SIZE
ROUND PUNCH & LOCATION SEE
A SERIES
WITH HEAD 4-7/8" NEW LENGTH SEE ABOVE TECHNICAL SECTION

4-11/16" THROW
2016 AWAY LENGTH
SHAPED PUNCH
WITH HEAD
1/8"
91130 UNITS SHIPPED WITH
DIA. KEY B.H.S.C.S. GUIDE RETAINER AS
SHOWN. TO INCREASE
GUIDE 1/8", FLIP 1018 GUIDE
2045 1" O.D.
STRIPPING x 1/2" I.D. AND REASSEMBLE.
SPRING
2-1/2"
8-3/8"
SHUT
2180 HEIGHT
RETAINER PIN
7/16"I.D.
2030
ROUND GUIDE
2-1/16"
2035
SHAPED GUIDE NOTE: FOR GUIDE OPTIONS,
3/4" O.D. REFER TO ADDL. PRODUCTS, 2-3/8"
2070
1" O.D. 3-1/2"

DIE
HEIGHT 1-3/4"
2120
9/16" THROW AWAY
2125 LENGTH
SHAPED DIE
3/4" O.D. 15/16" O.D. 1120 14055
1101
2121 3/8" DIA. SHAPED HOLDER 4" THROAT
PEDESTAL DIE 3/8" DIA.
PILOT PIN
14072 DIAMOND 14056
DIE ADAPTER 1-25/32" 2126 2-1/8" NEW LENGTH 15/32" 1-1/2" PILOT PIN SHAPED HOLDER 8" THROAT
1-1/4" O.D.
SHAPED 1-15/16 THROW 11.9mm 38.1mm
14074 PEDESTAL DIE AWAY LENGTH 14057
DIE ADAPTER SHAPED HOLDER 12" THROAT
(SHAPED)
1-1/4" O.D. Note: Pedestal dies can be altered to punch formed parts. Contact the UniPunch Sales Department.

30
AJ-1/ 1"
OPERATING SHUT HEIGHT: 8-3/8" (212.7mm) MIN. DIE CLEARANCE: .006" ( .15mm)
MIN. SHUT HEIGHT: 8-3/16" (208.0mm) MAX. PUNCH DIAMETER: .4375" (11.11mm)
UNIT OPEN HEIGHT:
DIE HEIGHT:
9-1/8" (231.8mm)
3-1/2" (88.9mm)
MAX. SQUARE:
.0937" (2.38mm)
.309" (7.85mm)
.0937" (2.38mm)
4
31.8mm width

Key kit: 9322
BASE UNITS 4A J-11⁄4P -LPD 14100P-LPD 4SA J-11⁄4P -LPD
14105P-LPD 4" 7" 9 lbs.
LESS PUNCH, DIE
Hardware kit: 9377
8A J-11⁄4P -LPD 14101P-LPD 8SA J-11⁄4P -LPD 14106P-LPD 8" 11" 10.5 lbs.
AND DIE ADAPTER
12A J-11⁄4P -LPD 14102P-LPD 12SA J-11⁄4P -LPD 14107P-LPD 12" 15" 15 lbs. Punch shim: N.A.
BASE UNITS 4A J-11⁄4A -LPD 14100A-LPD 4SA J-11⁄4A -LPD 14105A-LPD 4" 7" 9.5 lbs. Upper arm kit: 9733 Round
LESS PUNCH & DIE 8A J-11⁄4A -LPD 14101A-LPD 8SA J-11⁄4A -LPD 14106A-LPD 8" 11" 11.0 lbs. 9734 Shaped
(Includes Die Adapter) 12A J-11⁄4A -LPD 14102A-LPD 12SA J-11⁄4A -LPD 14107A-LPD 12" 15" 16.5 lbs.
COMPLETE UNITS 4A J-11⁄4 A 14100A 4SAJ-11⁄4 A 14105A 4" 7" 10 lbs.
WITH DIE ADAPTER 8A J-11⁄4 A 14101A 8SAJ-11⁄4 A 14106A 8" 11" 11.5 lbs.
(Includes Punch & Die) 12A J-11⁄4 A 14102A 12SAJ-11⁄4 A 14107A 12" 15" 16 lbs.
WITH PEDESTAL DIE 8A J-11⁄4 P 14101P 8SA J-11⁄4 P 14106P 8" 11" 11.5 lbs. *To order shaped unit w/ round
1" DIA.
LENGTH A
2171
PUNCH HEAD
1" 3/4" 1-7/8"
19.0mm
2113 7/16"DIA.
RETAINER RING
1-1/4" 9/16"
2111
ROUND PUNCH
A SERIES
2110
ROUND PUNCH SEE ABOVE & LOCATION SEE
WITH HEAD 4-7/8" NEW LENGTH
TECHNICAL SECTION
4-11/16" THROW
2115 AWAY LENGTH
SHAPED PUNCH
WITH HEAD
91130 UNITS SHIPPED WITH
1/8"
DIA. KEY B.H.S.C.S. GUIDE RETAINER AS
SHOWN. TO INCREASE
2140 1-1/4" O.D. RETAINER RETAINER 180 DEGREES
STRIPPING x 5/8" I.D. AND REASSEMBLE.
SPRING
2-1/2"
8-3/8"
SHUT
2180 HEIGHT
RETAINER PIN
7/16"I.D.
2130
ROUND GUIDE
2-1/16"
2135
SHAPED GUIDE NOTE: FOR GUIDE OPTIONS,
3/4" O.D. REFER TO ADDL. PRODUCTS,
2-3/8"
2170
LIFTER SPRING 1"
3-1/2"
1-1/8" O.D. DIE
HEIGHT 1-3/4"
2120
2125
SHAPED DIE 3/4" O.D.
15/16" O.D. 1120 14155
3/8" DIA. 1101
2121
3/8" DIA. HOLDER 4" THROAT
PEDESTAL DIE PILOT PIN
14172 15/16" O.D. DIAMOND 14156
DIE ADAPTER 1-25/32" 2126 15/32" 1-1/2" PILOT PIN HOLDER 8" THROAT
2-1/8" NEW LENGTH 38.1mm
1-1/4" O.D.
SHAPED 1-15/16 THROW 11.9mm
PEDESTAL DIE AWAY LENGTH
14157
14174 HOLDER 12" THROAT
DIE ADAPTER
(SHAPED)
1-1/4" O.D. Note: Pedestal dies can be altered to punch formed parts. Contact the UniPunch Sales Department.

UNIPUNCH
31
AJ-1/ 1" OPERATING SHUT HEIGHT: 8-3/8" (212.7mm) MIN. DIE CLEARANCE: .006" ( .15 mm)
2 UNIT OPEN HEIGHT:

DIE HEIGHT:
9-1/8" (231.8mm)
3-1/2" (88.9mm)
MAX. SQUARE:
.1250" (3.18mm)
.441" (11.20mm)
.0937" (2.38mm)
38.1mm width MAX. MATERIAL THICKNESS

Key kit: 9322
BASE UNITS 4AJ-11⁄2P-LPD 14200P-LPD 4SAJ-11⁄2P-LPD 14205P-LPD 4" 7" 13 lbs.
Hardware kit: 9377 LESS PUNCH, DIE 8AJ-11⁄2P-LPD 14201P-LPD 8SAJ-11⁄2P-LPD 14206P-LPD 8" 11" 16 lbs.
Punch shim: N.A. AND DIE ADAPTER 12AJ-11⁄2P-LPD 14202P-LPD 12SAJ-11⁄2P-LPD 14207P-LPD 12" 15" 19 lbs.
Upper arm kit: 9735 Round BASE UNITS 4AJ-11⁄2A-LPD 14200A-LPD 4SAJ-11⁄2A-LPD 14205A-LPD 4" 7" 13.5 lbs.
9736 Shaped LESS PUNCH & DIE 8AJ-11⁄2A-LPD 14201A-LPD 8SAJ-11⁄2A-LPD 14206A-LPD 8" 11" 16.5 lbs.
(Includes Die Adapter) 12AJ-11⁄2A-LPD 14202A-LPD 12SAJ-11⁄2A-LPD 14207A-LPD 12" 15" 19.5 lbs.
COMPLETE UNITS 4AJ-11⁄2 A 14200A 4SAJ-11⁄2 A 14205A 4" 7" 14 lbs.

WITH DIE ADAPTER 8AJ-11⁄2 A 14201A 8SAJ-11⁄2 A 14206A 8" 11" 17 lbs.
(Includes Punch & Die) 12AJ-11⁄2 A 14202A 12SAJ-11⁄2 A 14207A 12" 15" 20 lbs.
COMPLETE UNITS 4AJ-11⁄2 P 14200P 4SAJ-11⁄2 P 14205P 4" 7" 14 lbs.

WITH PEDESTAL DIE 8AJ-11⁄2 P 14201P 8SAJ-11⁄2 P 14206P 8" 11" 17 lbs.
*To order shaped unit w/ round (Includes Punch) 12AJ-11⁄2 P 14202P 12SAJ-11⁄2 P 14207P 12" 15" 20 lbs.
7/8" 1-7/8"
2271 1" 22.2mm
PUNCH HEAD
2213 5/8"DIA.
RETAINER RING 1-1/2" 9/16"
A SERIES
2211
ROUND PUNCH
2210 SEE ABOVE & LOCATION SEE
ROUND PUNCH TECHNICAL SECTION
4-11/16" THROW
2215 AWAY LENGTH
SHAPED PUNCH
WITH HEAD 91130 UNITS SHIPPED WITH
3/16" SHOWN. TO INCREASE
DIA. KEY FEED CLEARANCE BY
1018
AND REASSEMBLE.
2240 1-1/2" O.D.
STRIPPING x 3/4" I.D.
SPRING
2-1/2"
8-3/8"
SHUT
HEIGHT
2180
RETAINER
PIN 5/8"I.D.
2230
ROUND GUIDE NOTE: FOR GUIDE OPTIONS,
2-1/16"
2-3/8"
2235
SHAPED FITTED STRIPPERS PAGE 83
GUIDE
1" O.D.
2270
LIFTER 1" 3-1/2"
SPRING DIE
1-7/16"O.D. HEIGHT 1-3/4"
2220
2225
SHAPED DIE 1-1/8" O.D.
1" O.D. 1120 1101 14255
2221 3/8" DIA. 3/8" DIA. HOLDER 4" THROAT
PEDESTAL DIE DIAMOND
PILOT PIN
14272 PILOT PIN 14256
DIE ADAPTER 1-25/32"
1-1/2" O.D. 2226 2-1/8" NEW LENGTH 9/16" 1-1/2" HOLDER 8" THROAT
SHAPED 1-15/16 THROW 14.3mm 38.1mm
14274 PEDESTAL DIE AWAY LENGTH 14257
DIE ADAPTER HOLDER 12" THROAT
(SHAPED)
1-1/2" O.D.
Note: Pedestal dies can be altered to punch formed parts. Contact the UniPunch Sales Department.

32
AJ-2 "
UNIT OPEN HEIGHT: 9-1/8" (231.8mm) MIN. PUNCH DIAMETER: .1875" (4.76mm)
DIE HEIGHT: 3-1/2" (88.9mm) MAX. SQUARE: .618" (15.69mm)
MATERIAL FEED CLEARANCE: 7/16" (11.1mm) MIN. SHAPE DIMENSION: .1250" (3.18mm)
50.8mm width

Key kit: 9322
BASE UNITS 4AJ-2P-LPD 14300P-LPD 4SAJ-2P-LPD 14305P-LPD 4" 7" 18 lbs.
LESS PUNCH, DIE 8AJ-2P-LPD 14301P-LPD 8SAJ-2P-LPD 14306P-LPD 8" 11" 22 lbs. Hardware kit: 9377
AND DIE ADAPTER 12AJ-2P-LPD 14302P-LPD 12SAJ-2P-LPD 14307P-LPD 12" 15" 27 lbs. Punch shim: N.A.
BASE UNITS 4AJ-2A-LPD 14300A-LPD 4SAJ-2A-LPD 14305A-LPD 4" 7" 18.5 lbs. Upper arm kit: 9737 Round
LESS PUNCH & DIE 8AJ-2A-LPD 14301A-LPD 8SAJ-2A-LPD 14306A-LPD 8" 11" 22.5 lbs. 9738 Shaped
(Includes Die Adapter) 12AJ-2A-LPD 14302A-LPD 12SAJ-2A-LPD 14307A-LPD 12" 15" 27.5 lbs.
COMPLETE UNITS 4AJ-2 A 14300A 4SAJ-2 A 14305A 4" 7" 19 lbs.

WITH DIE ADAPTER 8AJ-2 A 14301A 8SAJ-2 A 14306A 8" 11" 23 lbs.
(Includes Punch & Die) 12AJ-2 A 14302A 12SAJ-2 A 14307A 12" 15" 28 lbs.
COMPLETE UNITS 4AJ-2 P 14300P 4SAJ-2 P 14305P 4" 7" 19 lbs.

WITH PEDESTAL DIE 8AJ-2 P 14301P 8SAJ-2 P 14306P 8" 11" 23 lbs.
(Includes Punch) 12AJ-2 P 14302P 12SAJ-2 P 14307P 12" 15" 28 lbs. *To order shaped unit w/ round
LENGTH A
1" 1" 1-7/8" 1-7/8"

2371 1" 25.4mm25.4mm
PUNCH HEAD
2313 7/8"DIA.
RETAINER RING
2" 2" 9/16" 9/16"
A SERIES
2311
ROUND PUNCH
2310
ROUND PUNCH THROAT
THROAT DEPTHDEPTH
RANGERANGENOTE: NOTE: FORSIZE
FOR SLOT SLOT SIZE
WITH HEAD 4-7/8" NEW LENGTH SEE ABOVE & LOCATION
& LOCATION SEE SEE
4-11/16" THROW SEE ABOVE TECHNICAL SECTION
TECHNICAL SECTION
2315 AWAY LENGTH
SHAPED PUNCH
WITH HEAD
9113091130 UNITS SHIPPED
/ $.50 UNITS SHIPPED WITH WITH
3/16" B.H.S.C.S.GUIDE RETAINER
B.H.S.C.S. GUIDE RETAINER
AS AS
DIA. KEY SHOWN. TO INCREASE
SHOWN. TO INCREASE
FEED CLEARANCE,
FLIP FLIP
1018 /1018
$3.00 FEED CLEARANCE,
1018 RETAINER
GUIDE RETAINER
GUIDE GUIDE 1018 GUIDE
2" O.D.
RETAINER
RETAINER 180 DEGREES AND AND
180 DEGREES
2340
x 1" I.D. REASSEMBLE.
STRIPPING REASSEMBLE.
SPRING
2-1/2"
8-3/8" 8-3/8"
SHUT SHUT
2180
RETAINER HEIGHTHEIGHT
PIN 7/8"I.D.
2330
ROUND GUIDE
2-1/16"
2335
SHAPED
1-1/4" O.D. 2-3/8" 2-3/8"
GUIDE REFER TO ADDL. PRODUCTS,
2370
LIFTER 1"
SPRING
3-1/2" 3-1/2"
DIE
2320-1
1-11/16"O.D. DIE SIZES DIE
1-1/2" DIA. OVER .749" HEIGHTHEIGHT 1-3/4" 1-3/4"
2320-2
ROUND DIE 3/4" NEW LENGTH 2325-1
9/16" THROW AWAY SHAPED DIE
2325-2 LENGTH SIZES OVER .749"
SHAPED DIE
1120 /1120
$5.50 1101 /1101
1 - 1/4" O.D. 1-1/2" O.D. 3/8" DIA.
3/8" DIA.
$5.00
3/8" DIA. 1435514355
/ $159.00
2321 PILOT PIN
PILOT PIN
3/8" DIA.
DIAMOND HOLDER HOLDER 4" THROAT
4" THROAT
3/4" DIAMOND
1 1/2" 1 1/2"
PEDESTAL DIE PILOT PIN1435614356
3/4" PILOT PIN
19.0mm19.0mm
/ $176.00
14372
DIE ADAPTER 38.1mm38.1mm HOLDERHOLDER 8" THROAT
8" THROAT
1-25/32" 2326 2-1/8" NEW LENGTH
1-7/8" O.D. SHAPED
PEDESTAL DIE 1-15/16 THROW 1435714357
/ $218.00
AWAY LENGTH HOLDERHOLDER 12" THROAT
12" THROAT
14374
DIE ADAPTER
(SHAPED) Note: Pedestal dies can be altered to punch formed parts. Contact14358 / $291.00
the UniPunch Sales Department.
1-7/8" O.D. HOLDER 18" THROAT

33
AJ-2 / 1" OPERATING SHUT HEIGHT: 8-3/8" (212.7mm) MIN. DIE CLEARANCE: .006" ( .15mm)
MIN. SHUT HEIGHT: 8-3/16" (208.0mm) MAX. PUNCH DIAMETER: 1.250" (31.75mm)
2 UNIT OPEN HEIGHT:

DIE HEIGHT:
9-1/8" (231.8mm)
3-1/2" (88.9mm)
MAX. SQUARE:
.2812" (7.14mm)
.883" (22.43mm)
.1250" (3.18mm)

Key kit: 9323
BASE UNITS 8AJ-21/2P-LPD 14401P-LPD 8SAJ-21/2P-LPD 14406P-LPD 8" 11" 31.5 lbs.
Hardware kit: 9357
LESS PUNCH & DIE 12AJ-21/2P-LPD 14402P-LPD 12SAJ-21/2P-LPD 14407P-LPD 12" 15" 41.5 lbs.
1109-48 pk.
1/16" thk./3 max. COMPLETE UNITS 8AJ-21/2 P 14401P 8SAJ-21/2 P 14406P 8" 11" 34.5 lbs.
WITH PEDESTAL DIE 12AJ-21/2 P 14402P 12SAJ-21/2 P 14407P 12" 15" 44.5 lbs.
Upper arm kit: 9739 Round (Includes Punch)
9740 Shaped
*To order shaped unit w/ round punch & die, add suffix "-RPD".
NOTE: FOR PUNCH SIZES ABOVE 1.250” DIAMETER

(31.75MM), PLEASE CONTACT UNIPUNCH TECHNICAL SALES
2485
PUNCH 3-1/4"
SCREW
F.H.S.C.S.
LENGTH A
1-3/8" 2-1/8"
1-1/2" DIA. 34.9mm
2484
PUNCH
DRIVER 2-15/32"
2-1/2" 9/16"
2440-10
A SERIES
STRIPPING
SPRING
SET OF 10
STACK AS THROAT DEPTH RANGE NOTE: FOR SLOT SIZE
SHOWN & LOCATION SEE
SEE ABOVE
TECHNICAL SECTION
2-1/2" DIA.
2442
SPRING 1-3/4"
GUARD 91130 UNITS SHIPPED WITH
2433 SHOWN. TO INCREASE
RETAINER 1018 FEED CLEARANCE BY
RING GUIDE 1/8", FLIP 1018 GUIDE
NOTE: FOR GUIDE OPTIONS, RETAINER RETAINER 180 DEGREES
2-11/16" REFER TO ADDL. PRODUCTS, AND REASSEMBLE.
2435 2-1/8" O.D.

GUIDE x 1-1/ 2" I.D.
8-3/8"
SHUT
HEIGHT
2470
LIFTER 2"
SPRING
2-7/16" DIA. 2-3/8"

1/4" DIA. KEY
2-13/32" NEW LENGTH
14411 2-7/32" THROW AWAY LENGTH
ROUND PUNCH
1-1/2" DIA.
3-1/2"
14416 DIE
SHAPED PUNCH HEIGHT 1-3/4"
2422 2-1/2"
PEDESTAL DIE
2428 1120
SHAPED 2-1/8" NEW LENGTH 3/8" DIA. 1101 14456
2-1/16" THROW AWAY LENGTH PILOT PIN 3/8" DIA. HOLDER 8" THROAT
PEDESTAL DIE DIAMOND
1-1/8" 1-1/2" PILOT PIN
14457
2459 28.6mm 38.1mm HOLDER 12" THROAT
ROUND DIE OVER 1.293"
Note: Pedestal dies can be altered to punch formed parts. Contact the UniPunch Sales Department.
2461
SHAPED DIE OVER 1.293"

34
OPERATING SHUT HEIGHT:

MIN. SHUT HEIGHT:
UNIT OPEN HEIGHT:
(MILD STEEL):
8-3/8" (212.7mm)
8-1/4" (209.5mm)
9-15/16" (252.4mm)
1/8" (3.18mm)
Available for both round and shaped holes, these
units feature extra wide feed openings to allow
DIE HEIGHT:

(STAINLESS STEEL):
3-1/2" (88.9mm)
MATERIAL FEED CLEARANCE: 1-1/4" (31.8mm)
MIN. DIE CLEARANCE: .012" (.30mm)
1/16" (1.6mm)
other formed parts. If your particular application
calls for sizes other than those shown, send your
FCU
Feed Clearance Units
“front feed” of channels, angles, extrusions and specifications for a price quotation.
1 C 11" COMPLETE ROUND UNITS

STANDARD UNITS
A (Complete with Round Punch, Die & Adapter)
2
3-3/8" Holder Part Max. Min.
2A 4-7/8" Width No. Punch Punch
8" Dia. Dia.
2B .4375 .0937
11⁄ 4" 22101A 11.1mm 2.38mm
8-3/8" 1
1 ⁄ 2" 22201A .6250
15.86mm
.1250
3.18mm
SHUT .8750 .1875
HEIGHT
1
2 ⁄ 4" 22301A
3 22.22mm 4.76mm
OPTIONAL UNITS
(Complete with Round Punch & Pedestal Die)
Max. Min.
1-1/4" Holder Part Punch Punch
FEED Width No. Dia. Dia.
4 CLEARANCE
11⁄ 4" .4375 .0937
4A 22101P 11.1mm 2.38mm
11⁄ 2" 22201P .6250 .1250
15.86 mm 3.18mm
5 1 .8750 .1875
2 ⁄ 4" 22301P
3-1/2" 22.22mm 4.76mm
6 6A DIE
HEIGHT
To order a unit less punch and die,
7 7A add the suffix “- LPD.”
8 9 10 11
8A B 9/16" DIA. COMPLETE SHAPED UNITS
1-1/2" 38.1mm HOLD DOWN HOLES
STANDARD UNITS
(Complete with Shaped Punch, Die & Adapter)
11/4" WIDE 11/2" WIDE 21/4" WIDE Model Part Max. Min.
No. No. Square Shaped
Dim.
A SERIES
Item Part Part Part
No. Description No. No. No. 11⁄ 4" 22106A .309 .0937
7.85mm 2.38 mm
11⁄ 2" 22206A .441 .0937
1 Punch Head 2075 22271 22371 11.2mm 2.38mm
1
2 ⁄ 4" 22306A .618 .1250
2 Round Punch 21111 22211 22311 15.69 mm 3.18mm
2A Round Punch with Head 21110 22210 22310 OPTIONAL UNITS

(Complete with Shaped Punch & Pedestal Die)
2B Shaped Punch with Head 21115 22215 22315 Holder Part Max. Min.
Width No. Square Punch
3 Stripping Spring 22140 22240 22340 Dia.
11⁄ 4" 22106P .309 .0937
4 Round Guide 22130 22230 22330 7.85mm 2.38mm
1
1 ⁄ 2" 22206P .441 .0937
11.2mm 2.38mm
4A Shaped Guide 22135 22235 22335
21⁄ 4" 22306P .618 .1250
15.69mm 3.18mm
5 Lifter Spring 22170 22270 22370
To order a shaped unit with round
Round Die 2120 2220 2320-2 punch & die, add the suffix “- RPD.”
6 Round Die w/ Collar (over .749") — — 2320-1
Shaped Die 2125 2225 2325-2
6A Shaped Die w/ Collar (over .749") — — 2325-1
COMMON DIMENSIONS
7 Round Pedestal Die 2121 2221 2321 Holder Throat Shipping

Width Depth A B C Weight
7A Shaped Pedestal Die 2126 2226 2326
11⁄ 4" 8" 11⁄ 4" 15⁄ 32" 1" 22 lbs.
8 Die Adapter (Round) 14172 14272 14372
11⁄ 2" 8" 11⁄ 2" 9⁄ 16" 1" 26 lbs.
8A Die Adapter (Shaped) 14174 14274 14374
21⁄ 4" 8" 21⁄ 4" 3⁄ 4" 13⁄ 8" 40 lbs.
9 Pilot Pin (Round) 1120 1120 1120
10 Pilot Pin (Diamond) 1101 1101 1101
11 Shaped Holder 22156 22256 22356 PH: (800) 828-7061
OR (715) 263-3900
Shaped Hole Conversion Kit 7140 7141 7142 [email protected]
WEB: www.unipunch.com
KITS Key Kit: 9411 9411 9413
& Hardware Kit: 9366 9366 9355
SHIMS Punch Shim: N.A. N.A. N.A.
Die Shim: 1018

35
AH-2 / 1" OPERATING SHUT HEIGHT: 8-3/8" (212.7mm) MIN. DIE CLEARANCE: .018" (.46mm)
2 UNIT OPEN HEIGHT:

DIE HEIGHT:
9-3/8" (238.1mm)
3-1/2" (88.9mm)
MAX. SQUARE:
.2500" (6.35mm)
.707" (17.96mm)
.1250" (3.18mm)


Model Part Model Part Throat Length Shipping
Shaped hole No. No. No. No. Depth A Weight
Key kit : 9306 BASE ASSEMBLIES 8AH-21⁄2 H-LPDH 2600-LPDH 8SAH-21⁄2 LPDH 2605H-LPDH 8" 12" 40 lbs.
LESS PUNCH, DIE
Hardware kit: 9358
AND DIE HOLDER
12AH-21⁄2 H-LPDH 2601-LPDH 12SAH-21⁄2 LPDH 2606H-LPDH 12" 16" 47 lbs.
Guide bushing 2065
BASE ASSEMBLIES 8AH-21⁄2 H-LPD 2600-LPD 8SAH-21⁄2 H-LPD 2605H-LPD 8" 12" 42 lbs.
installation kit: LESS PUNCH & DIE
12AH-21⁄2 H-LPD 2601-LPD 12SAH-21⁄2 H-LPD 2606H-LPD 12" 16" 49 lbs.
(Includes Die Holder)
COMPLETE UNITS 8 A H-21⁄2 H 2600H 8 SA H-21⁄2 H 2605H 8" 12" 46 lbs.

WITH DIE HOLDERS 12A H-21⁄2 H 2601H 12SA H-21⁄2 H 2606H 12" 16" 55 lbs.
COMPLETE UNITS 8 A H-21⁄2 BD 2600BD 8 SA H-21⁄2 BD 2605BD 8" 12" 46 lbs.

WITH BLOCK DIES 12A H-21⁄2 BD 2601BD 12SA H-21⁄2 BD 2606BD 12" 16" 56 lbs.
(Includes Punch)
THROAT DEPTH RANGE
2671 3-3/8" SEE ABOVE
PUNCH HEAD 84.1mm
91025
S.H.C.S.
2682 2611
STRIPPER ROUND PUNCH 2-1/2" 9/16"
BOLT 1-1/2" 2610
(2 REQ’D) ROUND PUNCH
2-1/4" 9/16" WITH HEAD
1" DIA. 2616 LENGTH A
1/2" DIA. SHAPED PUNCH 2778
2615 KEY NOTE: FOR
A SERIES
SHAPED PUNCH 1¼ "

2 SLOT SIZE &
WITH HEAD 91130
13/16" B.H.S.C.S. LOCATION SEE
1-1/2" 4-5/16" NEW LENGTH TECHNICAL
4-1/8" THROW 1¼ " SECTION
2681-2 4
SPRING AWAY LENGTH
RETAINER
(SET OF 2)
3" 91201
F.H.S.C.S. 2654 / $56.00
8-3/8" GUIDE BUSHING
91604
SHUT (CUTAWAY VIEW )
LOCKWASHER
HEIGHT
2677 2680 2-3/8"

PUNCH PLATE PUNCH RETAINER
2540-2
STRIPPING
SPRING
(SET OF 2) 2683 3-1/2"
STRIPPER BOLT DIE 2-1/2"
2-3/4" HEIGHT
3/8" (2 REQ'D)
2" O.D. x 1" I.D. DIA.
1001 1101
3/8" DIA. 3/8" DIA.
2655
PILOT PIN SHAPED HOLDER
1-1/4" 1-1/2" DIAMOND 8" THROAT
2673-2 PILOT PIN
4" LIFTER SPRING 41.3mm 38.1mm 2656
(SET OF 2) SHAPED HOLDER
12" THROAT
2-1/2" 0 DEGREE
9/16" O.D.
* NOTE:
WHEN
POSITION
x 3/8" I.D. ORDERING 2-7/16"
COMPLETE FRONT 90 DEGREE
UNITS OF UNIT POSITION
WITH BLOCK Shapes will be supplied as shown
2676 TYPE DIE A unless otherwise specified by customer.
STRIPPER PLATE SPECIFY 3-1/4"
2620 A&C 1-5/8
ROUND DIE 3/4" NEW LENGTH DIMENSIONS NEW LENGTH
9/16" THROW AWAY LENGTH 1-9/16" THROW
2625 2-1/8" DIA. AWAY LENGTH OPTIONAL
2621
SHAPED DIE BLOCK DIE BLOCK DIE
FOR PUNCHING
2674 91029 HOLES
ROUND DIE 1-7/16" 2626 S.H.C.S. CLOSE TO
HOLDER SHAPED (2 REQ’D)
BLOCK DIE ANGLE LEGS
CUTAWAY VIEW
2675
SHAPED DIE 3-1/4" C .750"
HOLDER MIN. DIM.

36
AH-3 "
OPERATING SHUT HEIGHT: 8-3/8" (212.7mm) MAX. PUNCH DIAMETER:
MIN. SHUT HEIGHT: 8-3/16" (208.0mm) 1.1250" (28.57mm) in 1/2" (12.7mm) M.S.
1.3750" (34.92mm) in 1/4" (6.4mm) M.S.
MAX. SQUARE: .972" (24.68mm)
MIN. DIE CLEARANCE:
.018" (.46mm)
1/2" (12.7mm)
.1250" (3.18mm)
5/32" (4.00mm)
76.2mm width
Model Part Model Part Throat Length Shipping All AH-3 units furnished
No. No. No. No. Depth A Weight with Shaped Driver
Key kit: 9307
BASE ASSEMBLIES 8AH-3-LPD 3700-LPD 8SAH-3-LPD 3705-LPD 8" 11 5/8" 73 lbs.
LESS PUNCH & DIE 12AH-3-LPD 3701-LPD 12SAH-3-LPD 3706-LPD 12" 15 5/8" 83 lbs. Hardware kit: 9359
Guide bushing 2065
COMPLETE UNITS 8AH-3 3700 8SAH-3 3705 8" 11 5/8" 75 lbs. installation kit:
(Includes Punch & Die) 12AH-3 3701 12SAH-3 3706 12" 15 5/8" 85 lbs.
91260
F.H.S.C.S. (NYLOK) THROAT DEPTH RANGE
3-5/16" SEE ABOVE
91120 3" 84.1mm
B.H.S.C.S.
3778
KEY 11/16"
3772 3/8" 3" 9/16"

PUNCH PLATE
3741-2 3779
1-5/8" PUNCH DRIVER LENGTH A
STRIPPING SPRING
(SET OF 2) 3784
A SERIES
STRIPPER BOLT
(4 REQ’D) NOTE: FOR
SLOT SIZE &
3-5/32" LOCATION SEE
TECHNICAL
3" 2" 91360 SECTION
S.S.S.
HALF
3/8" DIA. DOG
POINT 3754
GUIDE BUSHING
1" O.D. x 1/2" I.D. (CUTAWAY VIEW )
3740-2 8-3/8"
STRIPPING SPRING SHUT
(SET OF 2) HEIGHT
2513
ROUND PUNCH
1-1/8" 2519 2-7/8"
SHAPED PUNCH
3" 1/4"KEY
2-1/4" NEW LENGTH 3777

2-1/8" THROW DIE KEY
AWAY LENGTH
2" O.D. x 1" I.D. 2-1/2"
3742 3-1/2"
SPRING SPACER 3774-4 DIE
(2 REQ'D) LIFTER SPRING HEIGHT
1-7/8 (SET OF 4)
27/32" 19/32" O.D. 1001 1101
x 3/8" I.D. 3/8" DIA. 3/8" DIA. DIAMOND
1-3/4" PILOT PIN PILOT PIN
1-5/8" 1-1/2"
3773 41.3mm 38.1mm
STRIPPER PLATE 3755
3756
2524
23/32" THROW
2529 AWAY LENGTH
SHAPED DIE 2-15/16" SQ.

37
AH-3 / 1" OPERATING SHUT HEIGHT: 8-3/8" (212.7mm) MAX. PUNCH DIAMETER:
2.000" (50.8mm) in 1/4" (6.4mm) M.S.
2 UNIT OPEN HEIGHT:

DIE HEIGHT:
9-3/8" (238.1mm)
3-1/2" (88.9mm)
MAX. SQUARE:
.5000" (12.7mm)
1.414" (35.9mm)

.018" (.46mm)
1/2" (12.7mm)
.1250" (3.18mm)
5/32" (4.0mm)

Key kit: 9308
Hardware kit: 9360 BASE ASSEMBLIES 8AH-31⁄ 2-LPD 2500-LPD 8SAH-31⁄ 2-LPD 2505-LPD 8" 12" 40 lbs.
LESS PUNCH & DIE 12AH-31⁄ 2-LPD 2501-LPD 12SAH-31⁄ 2-LPD 2506-LPD 12" 16" 47 lbs.
1109- 48 pk.
1/16" thk./3 max. COMPLETE UNITS 8AH-31⁄ 2 2500 8SAH-31⁄ 2 2505 8" 12" 43 lbs.
Guide bushing (Includes Punch & Die) 12AH-31⁄ 2 2501 12SAH-31⁄ 2 2506 12" 16" 50 lbs.
2065
installation kit:
91072
S.H.C.S.
NYLOK 2-1/2"
THROAT DEPTH RANGE

2583 3-3/4" SEE ABOVE
SHAPED PUNCH 95.2mm
DRIVER
2682
STRIPPER 2" DIA.
BOLT 3-13/16"
(2 REQ’D) 2-1/4"
A SERIES
2511 3-1/2" 9/16"

1/2" DIA. ROUND PUNCH
2515
1-1/2" SHAPED
1-1/2" PUNCH
2681-2 LENGTH A
SPRING 2-13/32" NEW LENGTH
RETAINER 2-7/32" THROW AWAY 1¼ " 2778
(SET OF 2) 3" LENGTH 2 KEY NOTE: FOR SLOT
13/16" 91130 SIZE & LOCATION
1/4" 91201
SEE TECHNICAL
DIA. KEY F.H.S.C.S. B.H.S.C.S.
1¼ " SECTION
91604 4
LOCKWASHER
2572
PUNCH PLATE 2680 2585
PUNCH RETAINER GUIDE BUSHING
8-3/8" (CUTAWAY VIEW )
SHUT
2683 HEIGHT
2540-2
2-3/4" STRIPPER BOLT
STRIPPING SPRING 3/8" (2 REQ’D)
(SET OF 2) 2-3/8"
DIA.
2" O.D.
x 1" I.D. 2580
DIE
4" 2673-2 BLOCK
LIFTER SPRING
(SET OF 2)
2-1/2" 9/16" O.D. 3-1/2"
x 3/8" I.D. DIE 2-1/2"
HEIGHT
1001 1101
3/8" DIA. 3/8" DIA.
2573
PILOT PIN 2-5/16" 1-1/2" DIAMOND
STRIPPER 58.7mm 38.1mm
PLATE PILOT PIN 2555
2520 2556
ROUND DIE 3/4" NEW LENGTH 91030 SHAPED HOLDER 12" THROAT
9/16" THROW AWAY S.H.C.S.
2525 3-1/2" DIA. LENGTH (2 REQ’D)
SHAPED DIE DIE BLOCK SCREWS

38
AH-6 "
OPERATING SHUT HEIGHT: 8-3/8" (212.7mm) MAX. PUNCH DIAMETER:
1.500" (38.10mm) in 1/2" (12.7mm) M.S.
UNIT OPEN HEIGHT: 9-5/8" (244.5mm) 3.000" (76.20mm) in 1/4" (6.4mm) M.S.
DIE HEIGHT: 3-1/2" (88.9mm) MIN. PUNCH DIAMETER: 1.000" (25.40mm)
MATERIAL FEED CLEARANCE: 5/8" (15.9mm) MAX. SQUARE: 2.121" (53.87mm)
MIN. DIE CLEARANCE:
.018" ( .46mm)
1/2" (12.7mm)
.1875" (4.76mm)
5/32" (4.0mm)
139.7mm width
Model Part Model Part Throat Length Shipping All AH-6 units furnished
No. No. No. No. Depth A Weight with Shaped Driver
Key kit: 9309
BASE ASSEMBLIES 8AH-6 -LPD 2700-LPD 8SAH-6-LPD 2706-LPD 8" 121⁄ 2" 119 lbs. Hardware kit: 9361
LESS PUNCH & DIE 12AH-6 -LPD 2701-LPD 12SAH-6-LPD 2707-LPD 12" 161⁄ 2" 139 lbs. Punch shim:
For rounds 1109-12 pk.
2-1/4" dia. 1109-48 pk.
COMPLETE UNITS 8AH - 6 2700 8SAH-6 2706 8" 121⁄ 2" 124 lbs. & less: 1/16" thk./3 max.
(Includes Punch & Die) 12AH - 6 2701 12SAH-6 2707 12" 161⁄ 2" 144 lbs. For rounds
> 2-1/4" dia. N/A
*To order a shaped unit with round punch & die, add the suffix “- RPD” & all shapes:
Guide bushing 2065
installation kit:
91072
S.H.C.S.
NYLOK 2-1/2" 4-3/4" THROAT DEPTH RANGE
120.6mm SEE ABOVE
2779
2684 PUNCH DRIVER
STRIPPER 3" DIA.
BOLT 3-7/8"
(4 REQ’D) 2" 2512 5-1/2" 9/16"
ROUND PUNCH
A SERIES
1/2" DIA. 2516
SHAPED
1-1/2" PUNCH
1-1/2"
2681-4
SPRING 2-13/32" NEW LENGTH LENGTH A
RETAINER 2-7/32" THROW AWAY
(SET OF 4) 3" LENGTH NOTE: FOR
2778 SLOT SIZE
91202 1¼2" & LOCATION
1/4" KEY
F.H.S.C.S. (2 REQ’D) SEE TECHNICAL
DIA. KEY 91604 SECTION
13/16"
LOCKWASHER 91130
(2 REQ’D) 1¼4" B.H.S.C.S.
2772
PUNCH PLATE 2680
PUNCH RETAINER 2780
(2 REQ’D) GUIDE BUSHING
(CUTAWAY VIEW )
8-3/8"
SHUT
HEIGHT
2-11/16"
2685
2540-4 3/8" (2 REQ’D)
STRIPPING DIA. 3-1/2"
DIE
SPRING HEIGHT 2-1/2"
(SET OF 4)
2" O.D. 2673-2
x 1" I.D. 4" LIFTER SPRING 1001 1101
(SET OF 2) 3/8" DIA. 3" 3/8" DIA.
2-1/2" 9/16" O.D. PILOT PIN 1-1/2"
DIAMOND
76.2mm 38.1mm
x 3/8" I.D. PILOT PIN
2773 2756
STRIPPER SHAPED HOLDER 8" THROAT
PLATE
2757
27/32" NEW LENGTH
3820 23/32" THROW AWAY LENGTH
ROUND DIE 4-15/16" DIA.
3825
SHAPED DIE

39
OA-6 " OPERATING SHUT HEIGHT: 8-3/8" (212.7mm) MAX. PUNCH DIAMETER:
2.000" (50.80mm) in 3/8" (9.5mm) M.S.
UNIT OPEN HEIGHT: 9-5/8" (244.5mm) 4.000" (101.60mm) in 3/16" (4.8mm) M.S.
DIE HEIGHT: 3-1/2" (88.9mm) MIN. PUNCH DIAMETER: 1.500" (38.1mm)
MATERIAL FEED CLEARANCE: 5/8" (15.9mm) MAX. SQUARE: 2.828" (71.83mm)
139.7mm width MAX. MAT. THK. (M.S.):
MIN. DIE CLEARANCE:
3/8" (9.5mm)
.018" (.46mm)
.250" (6.35mm)
5/32" (4.0mm)

All OA-6 units furnished Model Part Model Part Throat Length Shipping
with Shaped Driver No. No. No. No. Depth A Weight
Key kit: 9314
Hardware kit: 9361 BASE ASSEMBLIES 8OA-6 -LPD 2800-LPD 8SOA-6-LPD 2805-LPD 8" 121⁄ 2" 119 lbs.
LESS PUNCH & DIE 12OA-6 -LPD 2801-LPD 12SOA-6-LPD 2806-LPD 12" 161⁄ 2" 139 lbs.
Punch shim:
For rounds 1109-12 pk.
2-1/4" dia. 1109-48 pk. COMPLETE UNITS 8OA- 6 2800 8SOA-6 2805 8" 121⁄ 2" 124 lbs.
& less: 1/16" thk./3 max. (Includes Punch & Die) 12OA- 6 2801 12SOA-6 2806 12" 161⁄ 2" 144 lbs.
For rounds
> 2-1/4" dia. N/A *To order a shaped unit with round punch & die, add the suffix “- RPD”
& all shapes:
Die shim: N.A.
91072
S.H.C.S. THROAT DEPTH RANGE
NYLOK 2-1/2" 4-3/4" SEE ABOVE
120.6mm
4-1/2" 2879
2684 PUNCH DRIVER
STRIPPER
BOLT 4-1/8" DIA.
(4 REQ’D) 9/16"
3-7/8" 5-1/2"
2" 2818
A SERIES
2815
1-1/2" SHAPED PUNCH
1-1/2"
2681-4
SPRING 1/4" 2-17/32" NEW LENGTH
RETAINER DIA. KEY 2-11/32" THROW AWAY LENGTH A
(SET OF 4) 3" LENGTH NOTE: FOR SLOT SIZE
91202 & LOCATION SEE
F.H.S.C.S.(2 REQ’D) TECHNICAL SECTION
2871 91604
PUNCH PLATE LOCKWASHER 2778
(2 REQ’D) KEY 1¼2"
2680
PUNCH RETAINER 13/16"
(2 REQ’D) 91130
1¼4" B.H.S.C.S.
2685
2540-4 STRIPPER BOLT
STRIPPING 2-1/2" 3/8" (2 REQ’D)
SPRING DIA. 8-3/8"
(SET OF 4) SHUT
2" O.D. HEIGHT
x 1" I.D. 4" 2673-2
2-1/2" (SET OF 2)
9/16" O.D.
2870 x 3/8" I.D.
STRIPPER 3-1/2"
PLATE DIE 2-1/2"
HEIGHT
2820 1-3/16" NEW LENGTH
ROUND DIE 1-1/16" THROW AWAY 1101
LENGTH 3/8" DIA.
5-1/2" DIA. 3-1/2" 1-1/2"
2825
SHAPED DIE 88.9mm 38.1mm DIAMOND
1001 PILOT PIN
4-15/16" I.D. 3/8" DIA.
13/16"
2850
2829 PILOT PIN SHAPED HOLDER 8" THROAT
ADAPTER
5-1/2" O.D.
2851
OPTION FOR DIAS. UNDER 3.000" SHAPED HOLDER 12" THROAT
2829 DIE ADAPTER
2512 ROUND PUNCH
3820 ROUND DIE
2516 SHAPED PUNCH
3825 SHAPED DIE

40
AD-4 "
OPERATING SHUT HEIGHT: 8-3/8" (212.7mm) MIN. DIE CLEARANCE: .018" (.46mm)
DIE HEIGHT: 3-1/2" (88.9mm) MAX. SQUARE: .795" (20.19mm)
101.6mm width

No. No. No. No. Depth A Weight conversion kit: N.A.
Key kit: 9310
BASE ASSEMBLIES 8AD-4-LPD 2630-LPD 8SAD-4-LPD 2635-LPD 8" 11 3⁄ 4" 72 lbs. Hardware kit: 9362
LESS PUNCH & DIE 12AD-4-LPD 2631-LPD 12SAD-4-LPD 2636-LPD 12" 15 3⁄ 4" 82 lbs.
Punch shim: N.A.
Die shim: N.A.
COMPLETE UNITS 8AD- 4 2630 8SAD-4 2635 8" 113⁄ 4" 75 lbs.
(Includes Punch & Die) Guide bushing
12AD- 4 2631 12SAD-4 2636 12" 15 3⁄ 4" 85 lbs. installation kit: 2065
THROAT DEPTH RANGE

3-3/4" SEE ABOVE
95.2mm
2668
PUNCH RETAINER SCREW 4"
91140
B.H.S.C.S. 1-1/4"
(4 REQ’D)
2638
PUNCH PLATE
LENGTH A
2778
4-1/8" NEW LENGTH NOTE: FOR
1¼ " KEY
A SERIES
4" THROW AWAY LENGTH 2 SLOT SIZE &
91130
1-3/8" DIA.
91312 TECHNICAL
STRIPPER S.S.S. 1¼ " SECTION
BOLT
2640
ROUND PUNCH
4
(2 REQ’D)
SOLD IN 2643 2646
SHAPED PUNCH 2642
ASS’Y ONLY BUSHING
8-3/8" (CUT AWAY VIEW)
UPPER SPRING SHUT
GUIDE 1" TOTAL HEIGHT
(2 REQ’D) TRAVEL 2645-4
SOLD IN 2643 LIFTER SPRING
ASS’Y ONLY (SET OF 4) 3"
4.218" 4" 1/2" O.D.
2643 X 9/32 I.D. 91029
STRIPPING
SPRING ASS’Y S.H.C.S.
(2 REQ’D)
STRIPPING CUTAWAY VIEW
SPRING 3-1/2"
SET OF 24 LOWER SPRING DIE
(2 SETS REQ’D) GUIDE (2 REQ’D) HEIGHT 1-3/4"
SOLD IN 2643 SOLD IN 2643
ASS’Y ONLY ASS’Y ONLY
1001 1101
2639 3/8" DIA. 2665
STRIPPER 1-1/4" 1-1/2" 3/8" DIA. SHAPED HOLDER
PILOT PIN DIAMOND
PLATE 31.7mm 38.1mm 8" THROAT
PILOT PIN 2666
91141 SHAPED HOLDER
B.H.S.C.S. 12" THROAT
(2 REQ’D)
1-5/8" NEW LENGTH
2641 1-9/16" THROW
ROUND BLOCK DIE AWAY LENGTH
FRONT 0 DEGREE POSITION
2647 3-1/4"
SHAPED BLOCK DIE OF UNIT
3-15/16" 90 DEGREE POSITION
Shapes will be supplied
as shown unless
otherwise specified
1-1/4" by customer
3-1/4"

41
ADJ-2" (50.8mm width)
AJD-2”
OPERATING SHUT HEIGHT: 8-3/8" (212.7mm) MAX. PUNCH DIAMETER: .5000" (12.70mm)
MIN. SHUT HEIGHT: 8-3/16" (208.0mm) MIN. PUNCH DIAMETER: .2812" (7.14mm)
UNIT OPEN HEIGHT: 9-1/8" (231.8mm) MAX. SQUARE: .353" (8.96mm)
DIE HEIGHT: 3-1/2" (88.9mm) MIN. SHAPE DIMENSION: .1250" (3.18mm)
For Stainless Steel Punching MATERIAL FEED CLEARANCE: 7/16" (11.1mm) MAX. MAT. THK. (S.S.): 1/4" (6.4mm)
MIN. DIE CLEARANCE: .006" (.1 mm) 14 TONS MAX.
KITS AND SHIMS Note: 25% of material thickness is suggested die clearance
Shaped hole COMPLETE ROUND UNITS COMPLETE SHAPED UNITS COMMON DIMENSIONS
Key kit: 9322 Model Part Model Part Throat Length Shipping
Hardware kit: 9377
Punch shim: N.A. 4AJD-2 17051 4SAJD-2 17056 4" 7" 19 lbs.
8AJD-2 17052 8SAJD-2 17057 8" 11" 23 lbs.

Upper Arm Kits: 9737 Round
12AJD-2 17053 12SAJD-2 17058 12" 15" 28 lbs.
9738 Shaped
To order a unit less punch and die, To order a shaped unit with round
add the suffix “- LPD”. punch & die, add the suffix “- RPD”.
LENGTH A
1" 1-7/8"
25.4mm
2371
PUNCH HEAD
2313 2313
RETAINER
RETAINER RING RING 2" 9/16"
17008
ROUND PUNCH ONLY
A SERIES
17007 LENGTH
ROUND PUNCH w/HEAD THROAT DEPTH RANGE NOTE: FOR SLOT SIZE
SHAPED PUNCH w/HEAD
91130 / $.50 UNITS SHIPPED WITH

SHOWN. TO INCREASE
1018 / $3.00 FEED CLEARANCE, FLIP
GUIDE 1018 GUIDE RETAINER
2340 2" O.D. RETAINER 180 DEGREES AND
STRIPPING x 1" I.D. REASSEMBLE.
SPRING
2-1/2"
8-3/8"
SHUT
2180 HEIGHT
RETAINER
PIN 7/8"I.D.
2330
ROUND GUIDE
2-1/16"
2335 2-3/8"
SHAPED
1-1/4" O.D.
GUIDE REFER TO ADDL. PRODUCTS,
2370
LIFTER 1" 3-1/2"
SPRING DIE
HEIGHT 1-3/4"
1-11/16"O.D.
1-1/2" O.D.
2321 1120 / $5.50
PEDESTAL DIE 1120
3/8" DIA.
1101 / $5.00
14355 / $159.00
3/8" DIA.PIN
PILOT 1101
3/8" DIA.
HOLDER 4" THROAT
2326
PILOT PIN 3/4" 3/8" DIA.
DIAMOND
SHAPED 2-1/8" NEW LENGTH
PEDESTAL DIE 1-15/16 THROW
1 1/2" DIAMOND
PILOT PIN 14356 / $176.00
AWAY LENGTH
19.0mm 38.1mm PILOT PIN HOLDER 8" THROAT
14357 / $218.00
HOLDER 12" THROAT
14358 / $291.00
HOLDER 18" THROAT

42
AHD-2½" (50.8mm width)
AHD-2 / 1"
OPERATING SHUT HEIGHT: 8-3/8" (212.7mm) MIN. DIE CLEARANCE: .018" (.46mm)
MIN. SHUT HEIGHT:
UNIT OPEN HEIGHT:
DIE HEIGHT:
8-3/16" (208.0mm)
9-3/8" (238.1mm)
3-1/2" (88.9mm)
MAX. SQUARE:
.8750" (22.22mm)
.2812" (7.14mm)
.618" (15.70mm)
2
MATERIAL FEED CLEARANCE: 5/8" (15.9mm) MIN. SHAPE DIMENSION: .1250" (3.18mm) For Stainless Steel Punching
MAX. MATERIAL THICKNESS 1/4" (6.4mm)
(STAINLESS STEEL): 24 TONS MAX.
Note: 25% of material thickness is suggested die clearance KITS AND SHIMS
COMPLETE ROUND UNITS COMPLETE SHAPED UNITS COMMON DIMENSIONS Shaped hole
Model Part Model Part Throat Length Shipping Key kit : 9306
Hardware kit: 9358
8AHD-2 1/2 17151 8SAHD-2 1/2 17155 8" 11 5/8" 43 lbs.
installation kit: 2065
12AHD-2 1/2 17152 12SAHD-2 1/2 17156 12" 15 5/8" 50 lbs. Guide bushing
THROAT DEPTH RANGE

2671 3-3/8" SEE ABOVE
PUNCH HEAD 84.1mm
91025
S.H.C.S.
2682 17108
STRIPPER ROUND PUNCH 2-1/2" 9/16"
BOLT 1-1/2" 17107
(2 REQ’D) ROUND PUNCH
2-1/4" 9/16" WITH HEAD
1" DIA. 17116 LENGTH A
1/2" DIA. SHAPED PUNCH 2778
17115 KEY NOTE: FOR
A SERIES
SHAPED PUNCH 1¼ "
2 SLOT SIZE &
WITH HEAD 91130
1-1/2" 4-7/16" NEW LENGTH TECHNICAL
1¼ " SECTION
2681-2 4
SPRING
RETAINER
(SET OF 2)
3" 91201
F.H.S.C.S. 2654 / $56.00
8-3/8" GUIDE BUSHING
91604
SHUT (CUTAWAY VIEW )
LOCKWASHER
HEIGHT
2677 2680 2-3/8"

PUNCH PLATE PUNCH RETAINER
2540-2
STRIPPING
SPRING
(SET OF 2) 2683 3-1/2"
STRIPPER BOLT DIE 2-1/2"
2-3/4" HEIGHT
3/8" (2 REQ'D)
2" O.D. x 1" I.D. DIA.
1001 1101
3/8" DIA. 3/8" DIA.
2655
PILOT PIN SHAPED HOLDER
1-1/4" 1-1/2" DIAMOND 8" THROAT
2673-2 PILOT PIN
4" LIFTER SPRING 41.3mm 38.1mm 2656
(SET OF 2) SHAPED HOLDER
12" THROAT
2-1/2"
9/16" O.D.
* NOTE:
WHEN
0 DEGREE
POSITION
x 3/8" I.D. ORDERING 2-7/16"
COMPLETE FRONT
OF UNIT 90 DEGREE POSITION
UNITS Shapes will be supplied as shown
WITH BLOCK unless otherwise specified by customer.
2676 TYPE DIE A
STRIPPER PLATE SPECIFY 3-1/4"
2620 A&C 1-5/8
ROUND DIE 3/4" NEW LENGTH DIMENSIONS NEW LENGTH
9/16" THROW AWAY LENGTH 1-9/16" THROW
2625 2-1/8" DIA. AWAY LENGTH OPTIONAL
2621
SHAPED DIE ROUND BLOCK DIE BLOCK DIE
FOR PUNCHING
2674 91029 HOLES
ROUND DIE 1-7/16" 2626 S.H.C.S. CLOSE TO
HOLDER SHAPED (2 REQ’D)
BLOCK DIE ANGLE LEGS
CUTAWAY VIEW
2675
SHAPED DIE 3-1/4" C .750"
HOLDER MIN. DIM.

43
AHD-3" (76.2mm width)
AHD-3”
OPERATING SHUT HEIGHT: 8-3/8" (212.7mm) MAX. PUNCH DIAMETER: 1.1250" (28.57mm)
MIN. SHUT HEIGHT: 8-3/16" (208.0mm) MIN. PUNCH DIAMETER: .3750" (9.53mm)
UNIT OPEN HEIGHT: 9-5/8" (244.5mm) MAX. SQUARE: .795" (20.19mm)
DIE HEIGHT: 3-1/2" (88.9mm) MIN. SHAPE DIMENSION: .1250" (3.18mm)
For Stainless Steel Punching MATERIAL FEED CLEARANCE: 5/8" (15.9mm) MAX. MAT. THK. (S.S.): 1/4" (6.4mm)
MIN. DIE CLEARANCE: .018" ( .46mm) 31 TONS MAX.
KITS AND SHIMS Note: 25% of material thickness is suggested die clearance
All AH-3 units furnished COMPLETE ROUND UNITS COMPLETE SHAPED UNITS COMMON DIMENSIONS
with Shaped Driver
Key kit: 9307 Model Part Model Part Throat Length Shipping
Hardware kit: 9359
8AHD-3 17251 8SAHD-3 17255 8" 11-5/8" 43 lbs.
Guide bushing 2065
installation kit: 12AHD-3 17252 12SAHD-3 17256 12" 15-5/8" 50 lbs.
91260
F.H.S.C.S. (NYLOK) THROAT DEPTH RANGE
3-5/16" SEE ABOVE
91120 3" 84.1mm
B.H.S.C.S.
3778
KEY 11/16"
3772 3/8" 3" 9/16"

PUNCH PLATE
3741-2 3779
1-5/8" PUNCH DRIVER LENGTH A
STRIPPING SPRING
(SET OF 2) 3784
A SERIES
STRIPPER BOLT
(4 REQ’D) NOTE: FOR
SLOT SIZE &
3-5/32" LOCATION SEE
TECHNICAL
3" 2" 91360 SECTION
S.S.S.
HALF
3/8" DIA. DOG
POINT 3754
GUIDE BUSHING
1" O.D. x 1/2" I.D. (CUTAWAY VIEW )
3740-2 8-3/8"
STRIPPING SPRING SHUT
(SET OF 2) HEIGHT
17207
ROUND PUNCH
1-1/8" 17215 2-7/8"
SHAPED PUNCH
3"
1/4"KEY
2-3/8" LENGTH 3777
DIE KEY
2" O.D. x 1" I.D. 2-1/2"

3742 3-1/2"
SPRING SPACER 3774-4 DIE
(2 REQ'D) LIFTER SPRING HEIGHT
1-7/8 (SET OF 4)
27/32" 19/32" O.D. 1001 1101
x 3/8" I.D. 3/8" DIA. 3/8" DIA. DIAMOND
1-3/4" PILOT PIN PILOT PIN
1-5/8" 1-1/2"
3773 41.3mm 38.1mm
STRIPPER PLATE 3755
3756
2524
23/32" THROW
2529 AWAY LENGTH
SHAPED DIE 2-15/16" SQ.

44
AHD-3½" (88.9mm width)
AHD-3 / 1"
OPERATING SHUT HEIGHT: 8-3/8" (212.7mm) MAX. PUNCH DIAMETER: 1.5000" (38.10mm)
MIN. SHUT HEIGHT:
UNIT OPEN HEIGHT:
DIE HEIGHT:
8-3/16" (208.0mm)
9-3/8" (238.1mm)
3-1/2" (88.9mm)
MAX. SQUARE:
.5000" (12.70mm)
1.060" (26.92mm)
.1250" (3.18mm)
2
MATERIAL FEED CLEARANCE: 5/8" (15.9mm) MAX. MAT. THK. (S.S.): 1/4" (6.4mm) For Stainless Steel Punching
MIN. DIE CLEARANCE: .018" ( .46mm) 42 TONS MAX.
Note: 25% of material thickness is suggested die clearance KITS AND SHIMS
COMPLETE ROUND UNITS COMPLETE SHAPED UNITS COMMON DIMENSIONS Shaped hole
Model Part Model Part Throat Length Shipping Key kit: 9308
Hardware kit: 9360
8AHD-3 1/2 17354 8SAHD-3 1/2 17358 8" 12" 75 lbs. Punch shim: 1109-12 pk.
12AHD-3 1/2 17355 12SAHD-3 1/2 17359 12" 16" 85 lbs. 1109- 48 pk.
1/16" thk./3 max.
To order a unit less punch and die, To order a shaped unit with round Guide bushing 2065
installation kit:
91072
S.H.C.S.
NYLOK 2-1/2"
THROAT DEPTH RANGE

2583 3-3/4" SEE ABOVE
SHAPED PUNCH 95.2mm
DRIVER
2682
STRIPPER 2" DIA.
BOLT 3-13/16"
(2 REQ’D) 2-1/4"
A SERIES
17307 3-1/2" 9/16"
17314
1-1/2" SHAPED
1-1/2" PUNCH
2681-2 LENGTH A
SPRING 2-1/2" NEW LENGTH
RETAINER 1¼ " 2778
(SET OF 2) 3" 2 KEY NOTE: FOR SLOT
91201 13/16" 91130 SIZE & LOCATION
1/4" F.H.S.C.S. B.H.S.C.S. SEE TECHNICAL
DIA. KEY 1¼ " SECTION
91604 4
LOCKWASHER
2572
PUNCH PLATE 2680 2585
PUNCH RETAINER GUIDE BUSHING
8-3/8" (CUTAWAY VIEW )
SHUT
2683 HEIGHT
2540-2
STRIPPING SPRING 3/8" (2 REQ’D)
(SET OF 2) 2-3/8"
DIA.
2" O.D.
x 1" I.D. 2580
DIE
4" 2673-2 BLOCK
LIFTER SPRING
(SET OF 2)
2-1/2" 9/16" O.D. 3-1/2"
x 3/8" I.D. DIE 2-1/2"
HEIGHT
1001 1101
3/8" DIA. 3/8" DIA.
2573
PILOT PIN 2-5/16" 1-1/2" DIAMOND
STRIPPER 58.7mm 38.1mm
PLATE PILOT PIN 2555
2520 2556
9/16" THROW AWAY S.H.C.S.
2525 3-1/2" DIA. LENGTH (2 REQ’D)

45
A SERIES
Corner
OPERATING SHUT HEIGHT: 8-3/8" (212.7mm) MATERIAL FEED CLEARANCE: 11/32" (8.7mm)
MIN. SHUT HEIGHT: 8-3/16" (208.0mm) MIN. DIE CLEARANCE: Die Clearance is
UNIT OPEN HEIGHT: 9" (228.6mm) preset at factory for notching
up to 1/4” (6.4mm) mild steel.
MAX. MATERIAL THICKNESS (STAINLESS STEEL): 3/32" (2.4mm)
N O T C H
Note: All Corner Notching Units have

A Series – Corner Notch Units: 5" x 5" and 3" x 3"
replaceable punch and die steels. HOLD DOWN SLOT FOR
T-SLOT MTG.
6010 5X5 LEFT HAND STRIPPING SCRAP DROPS OUT REAR OF UNIT
CORNER NOTCH SPRING L. H. R. H.
UNIT SHOWN UNIT UNIT
(6020 REPLACEABLE
6-7/8" RIGHT HAND PUNCH/
OPPOSITE) DIE STEELS
CUTTING EDGES
TANGENT .500 DIA.
TO .500 DIA. PILOT PINS
PILOT PINS TANGENT TO
1/2" CUTTING EDGE
1/4" 2-1/2"
PILOTS
3/4"
1/4" R. H. FEED L. H.
UNIT UNIT
4-1/2" 2-1/2" DETAIL CORNER
NOTCH
3/4"
11"
HOLD DOWN HOLE 5/8" DIA. FOR HOLD DOWN SLOT
TEMPLATE MTG. FOR T-SLOT MTG.
GREASE FITTING GROOVES 6440 LEFT HAND UNIT
NOTCHING UNITS FOR COMPLETE SHOWN REPLACEABLE
LUBRICATION 5-1/2" (6540 RIGHT HAND PUNCH/
OF PUNCH BLADES 8-3/8" DIE STEELS
SHUT OPPOSITE)
Part Max. Ship. HEIGHT STRIPPING
Type Notch SPRING
No. Wt. CUTTING EDGES
Dia. 1/2" TANGENT
11/32"
FEED PILOTS 1/4" TO .500 DIA.
CLEAR. PILOT PINS
6010 5"x 5" 102 lbs.
L.H. 3/4"
6440 3"x 3" 58 lbs. 3-1/2" 1/4" 3/4"
DIE 2-1/2" 2-1/2"
HEIGHT
6020 5"x 5" 102 lbs.
R.H. 8-1/8"
A SERIES
6450 3"x 3" 58 lbs. HOLD DOWN HOLE

5/8" DIA. TEMPLATE MTG.
10
13
9
6010 6020 6440 6450 3
14
Item No. Parts Description Part No. Part No. Part No. Part No.
1 Punch Blade (long) 6091 6091 6404 6404
2
2 Punch Blade (short) 6090 6090 6403 6403 1
3 Punch Plate 6074 6074 6439 6439 7 8
4 Die Steel (long) 6080 6081 7046 7047
5 Die Steel (short) 6082 6083 7044 7045
6 Set of Die Screws 6002 6002 7052 7052
(set of 8) (set of 8) (set of 6) (set of 6) 5
7 Spring (2 or 3 req’d) 6040 6040 6040 6040 4
8 Spring Cage 6043 6043 6043 6043
9 Retainer 2476 2476 2476 2476
10 Stripper Bolt 91401 91401 91401 91401
11 Round Pilot Pin 1006 1006 1006 1006
12 11
12 Diamond Pilot Pin 1116 1116 1116 1116
13 Punch Plate Screw 91080 91080 91080 91080
6
6060 and 6050 Gauging Methods

PH: (800) 828-7061
OR (715) 263-3900
[email protected]
WEB: www.unipunch.com Gauging plate Adjustable side
with built-in gauges for each
scales and cutting side
adjustable stops
UNIPUNCH
Set of 2
PH: 800.828.7061 • 716.825.7960 • FAX: 716.825.0581 • www.unipunch.com
Part No. 6060 Part No. 6050
HOLES IN PARTS. FAST. 48

MIN. SHUT HEIGHT:
UNIT OPEN HEIGHT:
DIE HEIGHT:
8-3/16" (208.0mm)
9" (228mm)
3-1/2" (88.9mm)
MIN. DIE CLEARANCE:

(MILD STEEL):
(STAINLESS STEEL):
Die Clearance is
preset at factory
1/4" (6.4mm)
3/32" (2.4mm)
6300
Flat Stock Cutoff Units
UniPunch “A” Series 6300
6300 - FLAT STOCK CUTOFF UNITS Flat Stock Cutoff Units are a
Max. Cutoff Max. Shipping self-contained two post die
Part No. B C
Width A Tonnage Weight shearing unit available in
6300-200 2" 101⁄ 2 91⁄ 4 14 85 lbs. widths up to 8” (203.2mm).
These units can be mounted
6300-400 4" 121⁄ 2 111⁄ 4 28 101 lbs. in a press or press brake in
6300-600 6" 141⁄ 2 131⁄ 4 42 116 lbs. conjunction with other “A”
6300-800 8" 161⁄ 2 151⁄ 4 56 133.5 lbs.
Series tooling or can be
used for stand-alone cut to
Note: For sizes not shown, contact UniPunch Sales length applications in mild
Department for application information and pricing.
steel up to 1/4” (6.4mm)
Note: Punch & die steels in Flat thickness. Other widths can
Stock Cutoff Units are not be manufactured to your
interchangeable. Units must be requirements.
returned to factory for replacement.
Spare punch & die steels can be
supplied with new units.
3/8” DIA. PILOT PIN
A SERIES
6"
1-3/4"
3"
“A” MAX. STOCK 3-5/8" 5/8"

WIDTH & PILOT LOCATION
9/16" WIDE HOLD DOWN SLOTS
“C”
“B”
8-3/8"
SHUT
HEIGHT
3-1/2"
DIE
HEIGHT
Ph:P(800)
H: (800) 828-7061 (US) 263-3900
OR (716) 825-7960
UNIPUNCH
828-7061 • (715) • FAX: (716) 825-0581
• Email: [email protected] • www.unipunch.com

51
B Series Lineup
B, BX, B-Notching, B-Shearing and B-Corner Radius
• 5-1/2” shut height & 2-19/32" die height
• Material Thickness: Up to 10 gauge (.1345”)
• Designed for press equipment with limited die space
B Units (Pages 55 - 61)

“B” and “BX” units are ideal for lighter duty punching applications and for press environments with
limited opening. Available “B” units holder widths are: 3/4”, 1-1/4”, 1-3/4”, 2-1/4”, 3” and 5”.
Holder width is important because it defines the minimum hole to hole distance. The “B” units are
widely used in industry to punch mild steel in thickness up to 10 gauge. Depending on your material
thickness, punch diameters are available up to 3.500” (88.90mm). (For thicker punching
applications, see the UniPunch “A” Series.)
B SERIES
Shown above are UniPunch “B” units mounted in a press brake with a limited opening between the press
ram and bed. Keyed mounting templates are available for positioning “B” units and gauges to produce
accurate parts with each stroke of the press.

53
B Series Lineup
B, BX, B-Notching, B-Shearing and B-Corner Radius
• 5-1/2” shut height & 2-19/32" die height
• Material Thickness: Up to 10 gauge (.1345”)
• Designed for press equipment with limited die space
B Series Notching Units (Pages 62 - 65)

These units are designed to operate as stand-alone tools or can be used in conjunction with the
UniPunch“B” Series Lineup of hole punching units to punch and notch parts within the same press setup.
Corner Notching Units (Pages 62 - 63)

UniPunch "B" Series Corner Notch Units are self-contained dies available in 90 degree left hand and
right hand units. Three models are offered for corner notch sizes of up to 3" x 3", 5" x 5" or 8" x 8".
Die clearance is pre-set at the factory for notching up to 10 gauge mild steel.
B-Series Flat Stock Cutoff Unit (Page 66)

UniPunch “B” Series 5300 Flat Stock Cutoff Units are self-contained two post die shearing units available
in widths up to 8”. These units can be mounted in a press or press brake adjacent to existing C-frame
tooling or stand-alone cut-to-length applications in up to 10 gauge mild steel. Other widths can be
manufactured to your requirements.
B Series Corner Radius Unit (Page 67)

The UniPunch “B” Series 4000 Radius Unit uses a modified B-3 holder. The unit is delivered complete
with holder, built-in squaring guides and a punch and die pair that permits four radii options. Typically this
unit is used as a stand-alone unit for putting corner radii on flat material up to 10 gauge mild steel.
UNIPUNCH
54
3"
BX- /
UNIT OPEN HEIGHT:
DIE HEIGHT:
5-7/8" (149.2mm)
2-19/32" (65.9mm)
MAX. SQUARE:
.0937" (2.38mm)
N.A.
N.A.
4
(MILD STEEL): 10 GA./.134" (3.4mm)
19mm width
ROUND UNITS COMMON DIMENSIONS BX KITS AND SHIMS
Model Part Throat Length Shipping Key kit: N.A.

No. No. Depth A Weight Hardware kit: 9370
BASE UNITS 4BX-3/4-LPD 3000-LPD 4" 7" 5.75 lbs. 1089-48 pk.
LESS PUNCH & DIE 8BX-3/4-LPD 3001-LPD 1/16" thk./3 max.
8" 11" 7.75 lbs.
Die shim: N.A.
COMPLETE UNITS 4BX-3/4 3000 4" 7" 6 lbs. Upper arm kit: 9761
(Includes Punch & Die) 8BX-3/4 3001 8" 11" 8 lbs.
BX-3/4 Unit for Round Holes Only
3033
STRIPPER LENGTH A
BOLT 1"
(2 REQ’D) 5/16"
1-1/8" 1-3/4"
28.6mm
3032
RETAINER PLATE
3/4" 3/8"
91203
F.H.S.C.S.
7/32"
PUNCH HEAD TECHNICAL SECTION
11/16" DIA.
5/16"DIA.
3111
ROUND PUNCH
3110
ROUND PUNCH 2-11/16" NEW LENGTH
B SERIES
WITH HEAD 2-1/2" THROW
AWAY LENGTH
5-1/2"
SHUT
HEIGHT
3/4" O.D.
3040 x 3/8" I.D.
STRIPPING 1-1/4"
SPRING
1-1/4"
5/16" I.D.
3030
GUIDE
1-17/32" REFER TO ADDL. PRODUCTS, 2-19/32"
FITTED STRIPPERS PAGE 83 DIE
HEIGHT 1-3/4"
1/2"DIA.
4273
1001
3/8" DIA.
3/4" O.D. PILOT PIN
3121 7/16"
ROUND 1/2" NEW LENGTH 1.11mm
DIE 7/16" THROW AWAY 3050 HOLDER 4" THROAT
LENGTH
1 / 2 " O.D. 3051 HOLDER 8" THROAT

55
B-1/ 1"
OPERATING SHUT HEIGHT: 5- 1/2" (139.7mm) MIN. DIE CLEARANCE: .006" ( .15mm)
UNIT OPEN HEIGHT:
DIE HEIGHT:
5-7/8" (149.2mm)
2-19/32" ( 65.9mm)
MAX. SQUARE:
.0937" (2.38mm)
.265" (6.73mm)
.0937" (2.38mm)
4
(MILD STEEL): 10 GA. /.134" (3.4mm)
31.8mm width

4B -11⁄4-LPD 3303-LPD 4SB -11⁄4-LPD 3305-LPD Key kit: 9317
BASE UNITS 4" 7" 8 lbs.
LESS PUNCH & DIE
8B -11⁄4-LPD 3300-LPD 8SB -11⁄4-LPD 3306-LPD 8" 11" 11 lbs. Hardware kit: 9372
12B -11⁄4-LPD 3301-LPD 12SB -11⁄4-LPD 3307-LPD 12" 15" 15 lbs. Upper arm kit: 9763 Round
4B -11⁄4 3303 4SB -11⁄4 3305 4" 7" 8.5 lbs. 9764 Shaped
COMPLETE UNITS
8B -11⁄4 3300 8SB -11⁄4 3306 8" 11" 11.5 lbs.
Die shim: 1091-12 pk.
12B -11⁄4 3301 12SB -11⁄4 3307 12" 15" 15.5 lbs. 1091-48 pk.
*To order a shaped unit with round punch & die, add the suffix “- RPD” 1/16" thk./3 max.
3372
PUNCH
RETAINER
LENGTH A
3/4" 1-7/8"
91203 19.0mm
F.H.S.C.S.
3371
9/32" 1-1/4" 9/16"
PUNCH HEAD
25/32" DIA.
ROUND PUNCH 3/8"DIA. TECHNICAL SECTION
3310 91220
ROUND PUNCH 1/8" DIA. KEY F.H.S.C.S.
WITH HEAD
1030
3315 2-5/8" NEW LENGTH GUIDE RETAINER
SHAPED PUNCH 2-7/16" THROW
WITH HEAD AWAY LENGTH
B SERIES
3316
SHAPED PUNCH 5-1/2"
SHUT
HEIGHT
3370 1"
LIFTER
SPRING
1-7/32" O.D.
1-1/8"
91010
3/8"I.D. S.H.C.S.
(2 REQ’D)
2-19/32"
3330 DIE
ROUND GUIDE HEIGHT
91601
ASS’Y 2-7/8" 1/4" LOCK
WASHER 2-3/8" 1-3/4"
(2 REQ’D)
3335
SHAPED GUIDE 3380
ASS'Y DIE BLOCK 1101 3/8" DIA. DIAMOND PILOT PIN
1" O.D. 1001
NOTE: FOR GUIDE OPTIONS, 3/8" DIA. 1/2" 1-1/2"
REFER TO ADDL. PRODUCTS, PILOT PIN 12.7mm 38.1mm
FITTED STRIPPERS PAGE 83 3358 SHAPED HOLDER 4" THROAT
2120 3355 SHAPED HOLDER 8" THROAT

9/16" THROW AWAY 3356 SHAPED HOLDER 12" THROAT
2125 LENGTH
SHAPED DIE
3/4" O.D.

57
B-1/ 3" OPERATING SHUT HEIGHT: 5-1/2" (139.7mm) MIN. DIE CLEARANCE: .006" ( .15mm)
4 UNIT OPEN HEIGHT:

DIE HEIGHT:
5-7/8" (149.2mm)
2-19/32" ( 65.9mm)
MAX. SQUARE:
.1250" (3.18mm)
.353" (8.96mm)
.0937" (2.38mm)
(MILD STEEL): 10 GA. /.134" (3.4mm)

Key kit: 9317 4B -13⁄4-LPD 3403-LPD 4SB -13⁄4-LPD 3405-LPD 4" 7" 13.5 lbs.
Hardware kit: 9372 BASE UNITS 8B -13⁄4-LPD 3400-LPD 8SB -13⁄4-LPD 3406-LPD 8" 11" 17.5 lbs.
LESS PUNCH & DIE 12B -13⁄4-LPD 3401-LPD 12SB -13⁄4-LPD 3407-LPD 12" 15" 20 lbs.
1081-48 pk.
1/16" thk./3 max. 4B -13⁄4 3403 4SB -13⁄4 3405 4" 7" 14 lbs.
COMPLETE UNITS 8B -13⁄4 3400 8SB -13⁄4 3406 8" 11" 18 lbs.
Die shim: 1091-12 pk. (Includes Punch & Die) 12B -13⁄4 3401 12SB -13⁄4 3407 12" 15" 21.5 lbs.
1091-48 pk.
1/16" thk./3 max.
Upper arm kit: 9765 Round *To order a shaped unit with round punch & die, add the suffix “- RPD”
9766 Shaped
LENGTH A
3472
PUNCH 1" 1-7/8"
RETAINER 25.4mm
91230
F.H.S.C.S.
1-3/4" 9/16"
3471 9/32"
PUNCH HEAD
1-1/8" DIA.
3411
ROUND PUNCH 1/2"DIA. TECHNICAL SECTION
3410 91220
ROUND PUNCH 1/8" DIA. KEY F.H.S.C.S.
WITH HEAD
1030
2-5/8" NEW LENGTH GUIDE RETAINER
3416
2-7/16" THROW
SHAPED PUNCH
AWAY LENGTH
3415
B SERIES
SHAPED PUNCH
WITH HEAD 5-1/2"
SHUT
HEIGHT
3470
LIFTER 31/32"
SPRING
1-11/16" O.D.
1-1/8"
91010
1/2"I.D. S.H.C.S.
(2 REQ’D)
3430 2-19/32"
ROUND DIE
GUIDE ASS’Y HEIGHT
2-7/8" 91601
1/4" LOCK
3435 WASHER 2-3/8" 1-3/4"
SHAPED (2 REQ’D)
GUIDE ASS’Y
3480
DIE BLOCK 1101 3/8" DIA. DIAMOND PILOT PIN
1001
3/8" DIA. 5/8" 1-1/2"
REFER TO ADDL. PRODUCTS, 1-3/8" O.D. PILOT PIN 15.9mm 38.1mm
FITTED STRIPPERS PAGE 83 3455 SHAPED HOLDER 4" THROAT
3456 SHAPED HOLDER 8" THROAT
2120
9/16" THROW AWAY
2125 LENGTH 3458 SHAPED HOLDER 18" THROAT
SHAPED DIE
3/4" O.D.

58
BX-2 / 1"
UNIT OPEN HEIGHT:
DIE HEIGHT:
5-7/8" (149.2mm)
2-19/32" (65.9mm)
MAX. SQUARE:
.250" (6.35mm)
.707" (17.96mm)
.0937" (2.38mm)
4
(MILD STEEL): 10 GA. /.134" (3.4mm)
57mm width

4BX -21⁄4-LPD 3542-LPD 4SBX -21⁄4-LPD 3546-LPD 4" 7" 17 lbs. Key kit: 9317
BASE UNITS 8BX -21⁄4-LPD 3543-LPD 8SBX -21⁄4-LPD 3547-LPD 8" 11" 24 lbs. Hardware kit: 9374
LESS PUNCH & DIE 12BX -21⁄4-LPD 3544-LPD 12SBX -21⁄4-LPD 3548-LPD 12" 15" 29.5 lbs.
4BX -21⁄4 3542 4SBX -21⁄4 3546 4" 7" 18 lbs. 9768 Shaped
COMPLETE UNITS 8BX -21⁄4 3543 8SBX -21⁄4 3547 8" 11" 24.5 lbs.
(Includes Punch & Die) 12BX -21⁄4 3544 12SBX -21⁄4 3548 12" 15" 30 lbs.
LENGTH A
1-1/4" 1-7/8"
31.7mm
3572
PUNCH
RETAINER
2-1/4"
9/16"
91250
F.H.S.C.S.
3571 9/32"
PUNCH HEAD THROAT DEPTH RANGE NOTE: FOR SLOT SIZE
1-5/8" DIA. & LOCATION SEE
SEE ABOVE
TECHNICAL SECTION
3511 1"DIA. 91220
ROUND PUNCH F.H.S.C.S.
3510 1030
ROUND PUNCH 1/8" DIA. KEY GUIDE RETAINER
WITH HEAD
B SERIES
3517 2-5/8" NEW LENGTH
SHAPED PUNCH 2-7/16" THROW
WITH HEAD AWAY LENGTH 5-1/2"
SHUT
3518 HEIGHT
SHAPED PUNCH
3570
LIFTER 1-1/4"
SPRING
1-1/8"
2-3/16" O.D.
91011
S.H.C.S.
1" I.D. (2 REQ’D)
2-19/32"
DIE
HEIGHT
91601
1/4" LOCK
2-7/8" WASHER 2-3/8" 1-3/4"
(2 REQ’D)
3581
DIE BLOCK 1101 3/8" DIA. DIAMOND PILOT PIN
NOTE: FOR GUIDE OPTIONS, 1001
REFER TO ADDL. PRODUCTS, 3/8" DIA. 1" 1-1/2" 3558 SHAPED HOLDER 4" THROAT
FITTED STRIPPERS PAGE 83 1-7/8" O.D. PILOT PIN 25.4mm 38.1mm
3521 3556 SHAPED HOLDER 12" THROAT
19/32" NEW LENGTH
ROUND DIE 17/32" THROW AWAY 3557 SHAPED HOLDER 18" THROAT
LENGTH
3526
SHAPED DIE 1 - 5 / 8 " O.D.

59
B-3 " OPERATING SHUT HEIGHT: 5-1/2" (139.7mm) MIN. DIE CLEARANCE: .006" ( .15mm)
DIE HEIGHT: 2-19/32" (65.9mm) MAX. SQUARE: 1.414" (35.9mm)
76.2mm width MAX. MAT. THK. (M.S.): 10GA. /.134" (3.4mm) MAX. MAT. THK. (S.S.): 1/16" (1.6mm)

Key kit: 9300 8B -3-LPD 3600-LPD 8SB -3-LPD 3606-LPD 8" 11" 27 lbs.
Hardware kit: 9375 BASE UNITS
LESS PUNCH & DIE
12B -3-LPD 3601-LPD 12SB -3-LPD 3607-LPD 12" 15" 34 lbs.
.
8B -3 3600 8SB -3 3606 8" 11" 28.5 lbs.

COMPLETE UNITS
12B -3 3601 12SB -3 3607 12" 15" 35.5 lbs.
91240
F.H.S.C.S.
LENGTH A
3671 1/4"
PUNCH HEAD 2-3/4" 1-5/8" 1-7/8"
41.3mm
3670 1-7/8"
LIFTER
SPRING
3" 9/16"
2-15/16" O.D.
3640 3/4" O.D.

STRIPPER x 13/32" I.D.
SPRING 1-1/2"
(6 REQ’D)
TECHNICAL SECTION
2-1/4"
91220
3675 NOTE: FOR GUIDE OPTIONS, F.H.S.C.S.
SHAPED
B SERIES

GUIDE FITTED STRIPPERS PAGE 83 1030
GUIDE RETAINER
2-9/16" O.D.
7/8
5-1/2"
3611 SHUT
PUNCH DRIVER HEIGHT
1-29/32"
2-21/32" NEW LENGTH
2-17/32" THROW
AWAY LENGTH
1/4"
3610-1 1-1/8"
ROUND PUNCH 1" 91014
TIP (OVER 1.124") S.H.C.S.
(2 REQ’D) 2-19/32"
DIE
91026 HEIGHT
S.H.C.S.
91601 1-3/4"
1/4" LOCK
WASHER 2-3/8"
7/8
(2 REQ’D)
3615
SHAPED PUNCH 2-21/32" NEW LENGTH 3680
2-17/32" THROW DIE BLOCK 1101
AWAY LENGTH 1001 3/8" DIA. DIAMOND PILOT PIN
3/8" DIA. 1-1/2" 1-1/2"
PILOT PIN 38.1mm 38.1mm
3610-2 1/4" DIA. KEY 3656
ROUND PUNCH SHAPED HOLDER 8" THROAT
(UNDER 1.125")
3657
9/16" THROW AWAY 3658
3625 LENGTH SHAPED HOLDER 18" THROAT
SHAPED DIE 2 - 9 / 1 6 " O.D.

60
OPERATING SHUT HEIGHT: 5- 1/2" (139.7mm)

MIN. SHUT HEIGHT:
UNIT OPEN HEIGHT:
DIE HEIGHT:

5-5/16" (134.9mm)
5-7/8" (149.2mm)
2-19/32" ( 65.9mm)
10GA. /.134" (3.4mm)
MIN. DIE CLEARANCE:
MAX. SQUARE:
.008" ( .2mm)
3.500" (88.90mm)
1.000" (25.40mm)
2.474" (62.84mm)
.1250" (3.18mm)
1/16" (1.6mm)
B-5
127mm width
"
KITS AND SHIMS

No. No. No. No. Depth A Weight conversion kit: N.A.
Key kit: 9318
BASE UNITS 8B-5-LPD 3800-LPD 8SB-5 3805-LPD 81⁄4" 113⁄4" 50 lbs. Hardware kit: 9376
LESS PUNCH & DIE 12B-5-LPD 3801-LPD 12SB-5 3806-LPD 121⁄4" 153⁄4" 65 lbs.
COMPLETE UNITS 8B-5 3800 8SB-5 3805 81⁄4" 113⁄4" 55 lbs.

(Includes Punch & Die) 12B-5 3801 12SB-5 3806 121⁄4" 153⁄4" 70 lbs.
To order a shaped unit with round punch & die, add the suffix “- RPD”
91152
B.H.S.C.S.
LENGTH A
3" 4-3/8"
3873 9/16" 76.2mm
PUNCH HEAD
6" DIA.
3870 1/2" O.D.
LIFTER SPRING x 13/32" I.D.
(4 REQ’D)
3/4" O.D. 2"
x 13/32" I.D.
3840 1-1/2"
STRIPPER
SPRING
(12 REQ’D) 5" 9/16"
4" O.D.
3881 2-5/16"
GUIDE
91104
B.H.S.C.S.
(3 REQ’D)
1471 3-9/16" I.D.
SPRING CLIP
(3 REQ’D) 1-7/8" REFER TO ADDL. PRODUCTS,
NOTE: FOR SLOT SIZE
THROAT DEPTH RANGE
& LOCATION SEE
SEE ABOVE
TECHNICAL SECTION
B SERIES
3871 1-11/32"
PUNCH
SLEEVE 91130
B.H.S.C.S.
3880
PUNCH
LOCATOR 1-5/8" 1002
GUIDE RETAINER
3833
RETAINER RING
1" 5-1/2"
3810 SHUT
ROUND PUNCH 1" HEIGHT
1-7/8"
1-1/4"
2-19/32"
2-11/32" DIE
3815 NEW LENGTH
SHAPED PUNCH 2-7/32" THROW HEIGHT
AWAY LENGTH 1-3/4"
2-3/8"
3-1/2"
3874 1101 3/8" DIA. DIAMOND PILOT PIN
3883 DIE BLOCK
ROUND
STRIPPER PLATE 9/32" 1001 3855
3/8" DIA. 2-7/8" 1-1/2 SHAPED HOLDER 8" THROAT
3882 3-23/32" PILOT PIN 73.0mm 38.1mm
SHAPED 3856
STRIPPER PLATE SHAPED HOLDER 12" THROAT
3820
ROUND DIE 27/32" 91030
NEW LENGTH S.H.C.S.
21/32" THROW (2 REQ’D)
3825 4 - 1 5 / 1 6 " O.D. AWAY LENGTH

61
B SERIES
Corner
OPERATING SHUT HEIGHT: 5-1/2" (139.7mm) MATERIAL FEED CLEARANCE: 3/16" (4.8mm)
MIN. SHUT HEIGHT: 5-5/16" (134.9mm) MIN. DIE CLEARANCE: Die Clearance is
UNIT OPEN HEIGHT: 5-7/8" (149.2mm) preset at factory
for notching from
DIE HEIGHT: 2-19/32" (65.9mm) 22 GA./.030" (.76mm )
MAX. MATERIAL THICKNESS MAX. MATERIAL THICKNESS
(MILD STEEL): 10 GA./.134" (3.4mm) (STAINLESS STEEL): 1/16" (1.6mm)
N O T C H
Note: All Corner Notching Units have B Series – Corner Notch Units: 5" x 5" and 3" x 3"
replaceable punch and die steels.
HOLD DOWN SLOT FOR
T-SLOT MTG.
SCRAP DROPS OUT REAR OF UNIT
7010 5X5 LEFT HAND STRIPPING L. H. R. H.
CORNER NOTCH UNIT SHOWN UNIT UNIT
SPRING
7020 (RIGHT HAND OPPOSITE)
REPLACEABLE
7-3/4" PUNCH/
DIE STEELS
CUTTING EDGES .500 DIA.
PILOT PINS
TANGENT TANGENT TO
TO .500 DIA. CUTTING EDGE
PILOT PINS 2-1/2"
1/4"
1/2"
3/4" R. H. FEED L. H.
UNIT DETAIL CORNER UNIT
1/4" 3/4" NOTCH
2-1/2"
7-1/2"
NOTCHING UNITS 10-1/8"
HOLD DOWN HOLE 5/8" DIA.
TEMPLATE MTG. 7040 3"x 3" LEFT HAND
Part Max. Ship. 5-1/2" CORNER NOTCH UNIT
Type Notch SHUT 7050 (RIGHT HAND
No. Wt. HEIGHT OPPOSITE)
Dia. 3/16" CUTTING EDGES
FEED TANGENT
CLEAR. 5-25/32" TO .500 DIA.
7010 5"x 5" 60 lbs. PILOT PINS
2-19/32" 1/4"
L.H. DIE
7040 3"x 3" 35 lbs. HEIGHT
3/4"
1/4" 3/4"
7020 5"x 5" 60 lbs. 2-1/2"
R.H. GREASE FITTING GROOVES FOR COMPLETE 5-7/16"
7050 3"x 3" 35 lbs. LUBRICATION OF PUNCH BLADES 7-5/32"
7010 7020 7040 7050

10
Item No. Parts Description Part No. Part No. Part No. Part No. 13
9
1 Punch Blade (long) 7091 7091 7004 7004 3
14
2 Punch Blade (short) 7090 7090 7003 7003
3 Punch Plate 6074 6074 7039 7039
B SERIES
4 Die Steel (side) — — 7044 7045 2

1
4A Die Steel (long) 6080 6081 –– ––
7 8
5 Die Steel (front) –– –– 7046 7047
5A Die Steel (short) 6082 6083 — —
6 Set of Die Screws 6002 6002 7052 7052
(set of 8) (set of 8) (set of 6) (set of 6) 5
5A
7 Spring (3 req’d) 7540 7540 7540 7540 4
8 Spring Cage 7043 7043 7043 7043 4A
9 Retainer 2476 2476 2476 2476
10 Stripper Bolt 91400 91400 91400 91400
11 Round Pilot Pin 1006 1006 1006 1006
12 11
12 Diamond Pilot Pin 1116 1116 1116 1116
13 Punch Plate Screw 91080 91080 91077 91077
6
6060 and 6050 Gauging Methods

PH: (800) 828-7061
OR (715) 263-3900
[email protected] Gauging plate
WEB: www.unipunch.com
with built-in Adjustable side
scales and gauges for each
adjustable stops. cutting side.
UNIPUNCH PH: 800.828.7061 • 716.825.7960 Set of 2

Part No. 6060• FAX: 716.825.0581 • www.unipunch.com
Part No. 6050
62/ 1998-1999 Catalog

MIN. SHUT HEIGHT:
UNIT OPEN HEIGHT:
DIE HEIGHT:
5-5/16" (134.9mm)
5-7/8" (149.2mm)
2-19/32" (65.9mm)
MIN. MATERIAL THICKNESS: 22 GA. (.76mm)
MIN. DIE CLEARANCE:

(MILD STEEL): 10 GA. /.134" (3.4mm)
Die Clearance is
preset at factory
7180
Corner Notch Unit
7180 “B” Series 8" x 8" / 90° Corner Notch Unit Note: Punch & die steels in 7180
Corner Notch Units are not
COMPLETE UNIT COMMON DIMENSIONS interchangeable. Unit must be
Part No.
Max. Notch (Corner) Max. ‘V’ Notch Shipping Weight
7180 8" x 8" / 90° 51⁄ 2" Deep / 90° 168 lbs. supplied with new units.
1-1/8" TYP.
13-1/2" 10-3/8" TYP.
The “B” series 8" x 8" Notch

Unit has been designed to
90d produce notch sizes greater
1.414" TYP. than our standard 5" x 5"
Corner Notch Units. The unit
is completely compatible
with all of the products in our
2-1/4" TYP.
“B” Series. Gauges sold
separately. See below.
B SERIES
1-1/2" TYP. 3/8" DIA. PiLOTS
13-1/2"
5-1/2"
SHUT
HEIGHT
2-19/32"
DIE
HEIGHT
Gauges for 7180 Notching Unit GAUGE ASSEMBLY

WITH BUILT IN SCALES AND
ADJUSTABLE STOPS
Part No.
7160*
*Includes mounting screws for
attachment to holder and gauge
plates.
Ph:P(800)
H: (800) 828-7061 (US) 263-3900
OR (716) 825-7960
UNIPUNCH
828-7061 • (715) • FAX: (716) 825-0581
• Email: [email protected] • www.unipunch.com
1998-1999 Catalog / 63
63 HOLES IN PARTS. FAST.
5300
Flat Stock Cutoff Units
MIN. SHUT HEIGHT:
UNIT OPEN HEIGHT:
DIE HEIGHT:
5-5/16" (134.9mm)
5-7/8" (149.2mm)
2-19/32" (65.9mm)
MIN. MATERIAL THICKNESS: 22 GA. (.76mm)
MIN. DIE CLEARANCE:

(MILD STEEL):
Die Clearance is
preset at factory
10 GA./.134" (3.4mm)
UniPunch “B” Series 5300 COMPLETE UNITS COMMON DIMENSIONS

Flat Stock Cutoff Units are
self-contained two post die Part No. Max. Cutoff B C Max. Shipping
Width A Tonnage Weight
shearing units available in
widths up to 8” (203.2mm). 5300-200 2" 101⁄ 2 91⁄ 4 8 55.5 lbs.
These units can be mounted 5300-400 4" 121⁄ 2 111⁄ 4 15 66 lbs.
in a press or press brake
adjacent to existing C-frame 5300-600 6" 141⁄ 2 131⁄ 4 23 77 lbs.
tooling or used in stand- 5300-800 8" 161⁄ 2 151⁄ 4 30 87.25 lbs.
alone cut-to-length
Note: For sizes not shown, contact UniPunch Sales
applications in mild steel up Department for application information and pricing.
to 10 gauge / .134”
(3.4mm) mild steel. Other
widths can be manufactured Note: Punch & die steels in Flat
to your requirements. Stock Cutoff Units are not
interchangeable. Units must be
supplied with new units.
3/8” DIA. PILOT PINS
6"
1-3/4"
B SERIES
3"
9/16" WIDE HOLD DOWN SLOTS

“A” MAX. STOCK 3-5/8" 5/8"
WIDTH & PILOT LOCATION
“C”
“B”
5-1/2"
SHUT
HEIGHT
2-19/32"
DIE
HEIGHT
UNIPUNCH
66 / 1998-1999 Catalog
4000
OPERATING SHUT HEIGHT: 5-1/2" (139.7mm) UNIT CAP.: 1/16"(1.6mm) to 1/4"(6.4mm)radius

14 GA. mild steel (1.9mm)
MIN. SHUT HEIGHT: 5-5/16" (134.9mm) .032 stainless steel (.81mm)
UNIT CAP.: 5/16"(7.9mm) to 1/2" (12.7mm) radius
UNIT OPEN HEIGHT: 5-7/8" (149.2mm) 10 GA. mild steel (3.4mm)
DIE HEIGHT: 2-19/32" (65.9mm) RADIUS SIZES:
16 GA. stainless steel (1.6mm)
SET#1–1/16,1/8,3/16&1/4" rad. (1.6,3.1,4.8,6.4mm)

Radius Unit
For Radii from 1/16" (1.6mm)
MATERIAL FEED CLEARANCE: 7/32" (5.5mm) SET#2–5/16,3/8,7/16&1/2" rad. (7.9,9.5,11.1,12.7mm) to 1/2"(12.7mm)
1/2-13 TAP
13
12
6
3" RECOMMENDED 5
LOCATION OF
HOLD DOWN HOLE 7
9
8
10
2 The UniPunch 4000 Unit is

designed to radius trim the
corners of parts (e.g. in
11 manufacturing signs, road
markers or cover plates).
3 4
14
This stand-alone radius
HOLDER SHOWN
unit is furnished complete
15 LESS GAGES with built-in squaring
guides for gauging 90
degree part blanks. Two
punch and die sets are
ITEM DESCRIPTION PART NO. available to produce eight
common radii. See
A Unit Complete with Punch & Die Sets for four standard radii 4000-1 specifications for Set #1
with Set #1 – 1⁄ 16", 1⁄ 8", 3⁄ 16" and 1⁄ 4" Radius or Set #2.
B Unit Complete with Punch & Die Sets for four standard radii 4000-2
with Set #2 – 5⁄ 16", 3⁄ 8", 7⁄ 16" and 1⁄ 2" Radius
B SERIES
Radius sizes can be
C Unit Complete with Punch & Die Sets for eight standard radii 4000 selected simply by rotating
with Sets #1& 2
the punch and die
1 Punch for radii from 1⁄ 16" thru 1⁄ 4" 4025-100 assembly. The die
2 Punch for radii from 5⁄ 16" thru 1⁄ 2" 4050-100 clearance is preset for
trimming mild steel up to
3 Die for radii from 1⁄ 16" thru 1⁄ 4" 4025-200 10 gauge thick.
4 Die for radii from 5⁄ 16" thru 1⁄ 2" 4050-200
Note: Custom and metric
5 Punch Head 3671 radii sizes are available
6 Punch Screw 91240 upon request. Contact the
UniPunch Sales
7 Lifter Spring 3670
Department for a quote.
8 Stripping Spring (set of 3) 3642
9 Punch Adapter 4015
10 Guide 4035
11 Screw (Punch Tip) 91010
12 Guide Retainer 1030
13 Screw (Guide Retainer) 91220
14 Screw (Die Block) (2 Req’d) 91014
15 Special Holder Only (Including Gauging Plates) 4056
4000 Radius Tool
Punch and Die
67
G Series
G - Triple Spring Unit
• 7-1/2” shut height
• Material Thickness up to 3/16”
• Adjustable punch head extends tool life
G Units (Page 70)
The UniPunch ‘G’ Series Triple Spring Unit has a 7½” shut height. They are designed for round hole punching. The advantage of the
Triple Spring Unit comes from the additional stripping spring force that allows the unit to be used to punch .3125” round holes in
3/16” material. (For thicker punching applications, see the “A” or “B” series.)
G - Triple Spring
Fixed Base Adjustable Base
The G series units are mounted to the UniPunch 5110 bed rail with either the fixed base or the adjustable base.
The fixed base is designed for straight line punching. The adjustable base allows 3/4” adjustment front to back (a total of 1 ½”).
G SERIES
G Series Usage
‘G’ Series units are designed for punching holes as close as ¾” center-to-center. These units feature a pedestal
die which is an advantage for punching formed parts such as aluminum extrusions, roll formed parts and small
channels and angles because the pedestal die can be modified to accommodate the profile of the part.
(For flat parts with close hole centers, UniPunch recommends the BX-3/4 because it can be used alongside other
B series units. (See page 55). The G-3/4 units are commonly used by storm door and window manufacturers and
in the recreational vehicle industry and by fabricators of other aluminum extrusions.
UNIPUNCH
68
G
S
E
R
I
E
S
Mounting Methods
and Accessories
PRESS BRAKE MOUNTING ACCESSORIES FOR ALL G SERIES UNITS

RAM PLATE (6" WIDE X 3/4" THICK) BED RAIL G SERIES
Shipping Shipping
Part No. Length Weight Part No. Length Weight
5019-24 24” 33 lbs. 5110-48 48" 92 lbs.
5019-48 48" 56 lbs. 5110-72 72" 138 lbs.
5019-72 72" 84 lbs. 5110-96 96" 184 lbs.
5019-96 96" 112 lbs. 5110-120 120" 230 lbs.
5019-120 120" 140 lbs. 5110-144 144" 276 lbs.
5019-144 144" 168 lbs.
Triple Spring Unit Press Brake mounting method shown

Single spring unit mounted in the same method and
operates at 6 ¼” shut height.
PRESS RAM
NUT, BOLT AND WASHER SET
5019 Part No.
RAM PLATE
3/4" 3/4" 3/4" 5143
FRONT TO BACK
ADJUSTMENT END GAUGE ASSEMBLY
Part No.
5085
Adjustable End Stop

has an adjustment
screw for quick
7-1/2" compensation for
SHUT
HEIGHT various work piece
4479
sizes.
GAGE ROD
(OPTIONAL)
4"
3-1/8"
DIE
HEIGHT
G SERIES
3.75
5143 5110
NUT, BOLT BED RAIL
& WASHER
3
1
PRESS BED
The G series units are mounted to the UniPunch

5110 bed rail with either the fixed base or the TYPICAL
adjustable base. The fixed base is designed for SPECIAL DIE
straight line punching. The adjustable base allows Made to
3/4” adjustment front to back (a total of 1 ½”). suit customer requirements

UNIPUNCH
69
Triple Spring Unit SPECIFICATIONS & OPERATING INSTRUCTIONS
G- / 3" OPERATING SHUT HEIGHT: 7-1/2" (190.50mm) MATERIAL FEED CLEARANCE: 3/16" (4.8mm)
MIN. SHUT HEIGHT: 7-5/16" (185.72mm) MIN. DIE CLEARANCE: .006" ( .15mm)
UNIT OPEN HEIGHT: 8" (203.2mm) MAX. PUNCH DIAMETER: .3125" (7.94mm)
4 DIE HEIGHT:
(MILD STEEL):
3-1/8" (79.4mm)
3/16" (4.8mm)
(STAINLESS STEEL):
.0937" (2.38mm)
.062" (1.57mm)
19.0 mm width
KITS AND SHIMS COMPLETE ROUND UNITS COMMON DIMENSIONS
Hardware kit: 9385 Model Max. Punch Throat Shipping
Punch shim: N.A. No. Diameter Depth Weight
Die shim: N.A. G-4221 .156 4" 7 lbs.
UNITS WITH
FIXED BASE G-4222 .250 4" 7 lbs.
G-4226 .3125 4" 7 lbs.
GA-4221 .156 4" 7 lbs.
UNITS WITH GA-4222 .250 4" 7 lbs.
ADJUSTABLE BASE
GA-4226 .3125 4" 7 lbs.
To order a unit less punch and die, add the suffix “- LPD”.
4219 9/16"
HEAD NUT
4239
LOCK NUT
3/4"
4217
PUNCH 4-5/16" NEW LENGTH 4"
4-1/16" THROW
4218 AWAY LENGTH
PUNCH COMPLETE
2"
4413
TRIPLE SPRING
STRIPPING
GUIDE ASS’Y 7-1/2"
(SPECIFY SHUT
PUNCH SIZE HEIGHT
WHEN ORDERING)
4479
GAGE ROD
(OPTIONAL)
3-1/8"
G SERIES
DIE
HEIGHT
4243
RETAINER RING
4273
3/4" O.D.
2-5/8"
NEW 1.781"
LENGTH NEW LENGTH
1/2" DIA. 3/4" DIA.
3/8" DIA. 3/8" DIA. 3/8" DIA.
4221 4222 4226

PEDESTAL DIE PEDESTAL DIE PEDESTAL DIE
.174" MAX DIA. .268" MAX DIA. .330" MAX DIA.

70
AE
S SPECIFICATIONS & OPERATING INSTRUCTIONS
E
R OPERATING SHUT HEIGHT: 10-3/8" (263.5mm) MAX. PUNCH DIAMETER: .625" (15.87mm)
I MIN. SHUT HEIGHT: 10-1/4" (260.3mm) MIN. PUNCH DIAMETER: .1875" (4.76mm)
E MAX. SQUARE: .441" (11.2mm)
S UNIT OPEN HEIGHT: 11" (279.4mm)
MIN. SHAPE DIMENSION: .0937" (2.38mm)
For Channels DIE HEIGHT: 5-1/2" (139.7mm) MAX. MAT. THK.: 4" (5.4#) CHANNEL
(Based on 50,000 P.S.I.
and Extrusions MIN. DIE CLEARANCE: .006" ( .15mm) shear strength)
KITS AND SHIMS

COMPLETE ROUND UNITS COMPLETE SHAPED UNITS COMMON DIMENSIONS
Shaped hole
conversion kit: 7134 Part Part Throat Shipping
Key kit: 9300 No. No. Depth Weight
Hardware kit: 9343 TAPERED DIE 2090 2095 1" 16 lbs.
Punch shim: N.A. FLAT DIE 2090F 2095F 1" 16 lbs.
Die shim: 1092- 12 pk. To order a unit less punch and die, add the suffix “- LPD”.
1092- 48 pk.
1/16" thk./2 max. To order a shaped unit with round punch & die, add the suffix “- RPD”.

9738 Shaped
1"
1-1/2" DIA. 25.4mm
2371 1"
This standard unit is
PUNCH HEAD 2" 9/16" specifically designed
7/8"DIA. for 3" (4.1#) and
4" (5.4#) structural
channels; however, the
2311 large cutaway section
ROUND PUNCH
2310 91130
permits the punching
ROUND PUNCH B.H.S.C.S. of a large variety of
4-3/4" THROW 1018 I-beams, angles,
2315
AWAY LENGTH GUIDE RETAINER
SHAPED PUNCH special shapes, and
WITH HEAD
extrusions. The
3/16" tapered dies, Part
DIA. KEY 10-3/8"
SHUT Nos. 2092 and 2097,
HEIGHT have a die face angled
2340 2" O.D. 1" 1" to accommodate the
STRIPPING x 1" I.D.
SPRING flange of the channel,
2-1/2" as shown in the
drawing. Standard
dies are required for
2-1/4"
5-1/2"
punching flat stock.
2180
RETAINER 7/8"I.D. DIE
PIN HEIGHT
2330 9/16"
ROUND GUIDE 2"
2-1/16"
2335 1-9/16"
SHAPED
GUIDE 1-1/4" O.D.
2096
SHAPED HOLDER
AE SERIES
2370 1001 1101

LIFTER 1" 1-1/2"
3/8" DIA. 3/8" DIA.
SPRING PILOT PIN 38.1mm DIAMOND PILOT PIN
4-1/8" MIN.
1-11/16"O.D.
2220
ROUND DIE
0 DEGREE POSITION Note: 2097 Tapered
2225 3/4" NEW LENGTH (OPTIONAL)
SHAPED DIE 5/8" THROW AWAY LENGTH Faced Dies are keyed for
2092
1" O.D. one position only. They will
TAPERED ROUND DIE be furnished in the 90
90 DEGREE POSITION
2097 (PROVIDED STANDARD degree position shown left
TAPERED SHAPED DIE UNLESS OTHERWISE
SPECIFIED) unless otherwise specified.
TAPERED DIES ARE NOT INDEXABLE
An infinite number of variations of holder shapes can be designed SEND

to accommodate irregular shapes and extrusions using standard DRAWINGS
“A” or “B” Series components in the special holders. Shown are FOR PRICE
examples of custom units. QUOTATION

72
TP (Tube & Pipe) Series Lineup
TP-1 ¼, TP-2-3/8 , TP-2, TP-2M and TP-AE
• Punch round and shaped tubing
• Punch both sides of tube, or just one side
• Punch “dimpled” holes or deformation-free holes
TP-1 ¼ Tube & Pipe Punching Unit (Page 74)

The TP-1 1/4 unit provides two sided punching in round or shaped tubes. The unit is designed for
punching tube diameters from 9/16” O.D. to 1 ¼” O.D. Each assembly top and bottom contains a
punch to pierce one hole in-line on each side of the tube. The tubing is supported on all sides during
punching. If only one hole is desired, simply remove one of the punches. Depending on your material
thickness, standard punch diameters are available from .0937” to .500”. Non-standard tooling for larger
hole sizes and/or shaped hole punching is also available.
TP-2 3/8 Tube & Pipe Punching Unit (Page 75)

The TP-2 3/8 unit provides two sided punching in round or shaped tubes. The unit is designed for
punching tube diameters from 1 5/16” O.D. to 2 3/8” O.D. Each assembly top and bottom contains a
punch to pierce one hole in-line on each side of the tube. The tubing is supported on all sides during
punching. If only one hole is desired, simply remove one of the punches. Depending on your material
thickness, standard punch diameters are available from .0937” to .500” (12.7mm). Non-standard
tooling for larger hole sizes and/or shaped hole punching is also available.
TP-2 Tube & Pipe Punching Unit (Page 76)

The TP-2 unit provides straight through holes with one punch in round or shaped tubing. The unit is
designed for punching tube diameters from 9/16” O.D. to 1” O.D. The tubing is supported on all sides
during punching. The top hole is dimpled; the bottom hole is punched into a die, providing a dimple free
hole. (UniPunch offers custom mandrel style punching units for dimple free holes. See TP-2M.)
Depending on your material thickness, punch diameters are available from .0937” to .4375”. Non-
standard tooling for shaped hole punching is also available.
TP-2M Unit Mandrel Tube Punching (Page 77 & 78)

The TP-2M mandrel style unit provides dimple-free holes in round, square or rectangular tube or pipe.
The unit is designed for punching tube sizes up to 1”, and each unit is designed for the particular hole
TP SERIES
size and tubing application. Depending on your material thickness, standard punch diameters are
available up to .4375”. Non-standard tooling for shaped hole punching is also available.
TP-AE Unit Mandrel Tube Punching (Page 77 & 79)

The TP-AE mandrel unit provides dimple-free holes near the end of round or shaped tube or pipe.
Maximum hole size or shape depends on tube size and material wall thickness. The unit can also be
used for notching or slitting the end of the tube.
Note: For custom tube & pipe fabricating applications, contact the UniPunch Sales Department.

73
TP-1/ 1" MAX. SHUT HEIGHT: 6-1/4" (158.7mm) MAX. WALL THICKNESS
MIN. SHUT HEIGHT: 6-1/8" (155.6mm) (MILD STEEL): .125" (3.18mm)
4
MAX. TUBE SIZE: 1-1/4" O.D. (31.7mm) MIN. WALL THICKNESS: .031" (.79mm)
round or square Note: For stainless steel tube punching applica-
tions contact UniPunch Sales Department
MIN. TUBE SIZE: 9/16" O.D. (14.3mm)
round or square MAX. HOLE DIAMETER: .500" (12.7mm)
Dia./Square Max. Note: For shaped holes,
contact UniPunch Sales Department
TO ORDER, SPECIFY:
PUNCH SELECTION CHART
• Size of Tube
Punch Part
• Hole Diameter Tube O.D. Length No.
• Wall Thickness 9⁄ 16" to 11⁄ 16" 31⁄ 32" 17210
• Type of Material 4-1/4"
3⁄ 4" to 7⁄ 8" 229⁄ 32" 17211 2-1/8"
15⁄ 16" 11⁄ 16" 213⁄ 16"
Note: Because there is no to 17212
die to support the tube at 11⁄ 8" to 11⁄ 4" 223⁄ 32" 17213 1-1/2"
38.1mm
the site of the hole, tubes
distort when punching. 3/4"
Distortion varies depending
on punch size, tube O.D., 2-1/2"
5"
wall thickness, and material 127.0mm
type.
MOUNTING SCREWS
6
NOT INCLUDED IN 7
ASSEMBLY
1 3 6-1/4" MAX.
SHUT HEIGHT
TOP ASS’Y 6-1/8" MIN.
8
9
1A 3-1/16"
BOTTOM 4
ASS’Y
TP SERIES
FOR ROUND TUBES FOR SQUARE TUBES

UP TO 1.250" O. D. UP TO 1.250" SQ.
Item Description Part No. Part No.
Complete Unit (Includes Top & Bottom Punches) 17200 17300
1 Top Ass’y (Includes Punch) 17205 17305
1A Bottom Ass’y (Includes Punch) 17206 17306
2 Punch Plate 17271 17271
3 Top Stripping Spring (Red) (2 Req'd) 17140 17140
4 Bottom Stripping Spring (Blue) (2 Req'd) 17160 17160
5 Stripper Bolt (2 Per Ass'y) 17138 17138
6 Roll Pin (1⁄ 8" Dia. x 3⁄ 16") 91679 91679
7 Mounting Screw (3⁄ 8"-16 x 1" S.H.C.S.) 91027 91027
8 Top Stripping Guide Only (Specify Tube O.D.) 17250 17350
9 Bottom Stripping Guide Only (Specify Tube O. D.) 17253 17353
UNIPUNCH PPh:
H: (800)
800.828.7061 • 716.825.7960
828-7061 • (715) • FAX
263-3900 • Email: : 716.825.0581• •Web:
[email protected] www.unipunch.com
www.unipunch.com

TP-2 / 3"
MAX. SHUT HEIGHT: 6-3/4" (171.4mm) MAX. WALL THICKNESS
8
MAX. TUBE SIZE: 2-3/8" O.D. (60.3mm) MIN. WALL THICKNESS: .031" (.79mm)
round or square Note: For stainless steel tube punching applica-
tions contact UniPunch Quotations Department
MIN. TUBE SIZE: 1-5/16" O.D. (33.3mm)
round or square MAX. HOLE DIAMETER: .500" (12.7mm)
Note: For shaped holes,
contact UniPunch Sales Department
Dia./Square Max.
TO ORDER, SPECIFY:
PUNCH SELECTION CHART
Punch Part
• Size of Tube
Tube O.D. Length No. • Hole Diameter
15⁄ 16" to 17⁄ 16" 31⁄ 32" 17210 5-3/4" • Wall Thickness
2-7/8"
• Type of Material
11⁄ 2" to 15⁄ 8" 229⁄ 32" 17211
111⁄ 16" to 2" 213⁄ 16" 17212 Note: Because there is no
21⁄ 16" to 23⁄ 16" 223⁄ 32" 17213 1-1/2" die to support the tube at
38.1mm the site of the hole, tubes
21⁄ 4" to 23⁄ 8" 25⁄ 8" 17214
3/4" distort when punching.
on punch size, tube O.D.,
3-1/4"
wall thickness, and material
6-1/2" type.
165.1mm
MOUNTING SCREWS
NOT INCLUDED IN 7 6
ASSEMBLY
1 3
6-3/4" MAX.
TOP ASS’Y SHUT HEIGHT
5 6-5/8" MIN.
9
3-5/16"
1A
BOTTOM
4
ASS’Y
TP SERIES
UP TO 2.375" O. D. UP TO 2.375" SQ.
Complete Unit (Includes Top & Bottom Punches) 17202 17302
1 Top Ass’y (Includes Punch) 17223 17323
1A Bottom Ass’y (Includes Punch) 17224 17324
2 Punch Plate 17272 17272
3 Top Stripping Spring (Red) (2 Req'd) 17140 17140
4 Bottom Stripping Spring (Blue) (2 Req'd) 17160 17160
5 Stripper Bolt (2 Per Ass'y) 17139 17139
6 Roll Pin (1⁄ 8" Dia. x 3⁄ 16") 91679 91679
7 Mounting Screw (3⁄ 8"-16 x 1" S.H.C.S.) 91027 91027
8 Top Stripping Guide Only (Specify Tube O.D.) 17262 17362
9 Bottom Stripping Guide Only (Specify Tube O. D.) 17263 17363

UNIPUNCH
75
TP-2
1" (25.4mm) round max.
7/8 " (22.2mm) square max.
" OPERATING SHUT HEIGHT: 9-3/8" (238.1mm)
MIN. SHUT HEIGHT:
UNIT OPEN HEIGHT:
MAX. TUBE SIZE:
MIN. TUBE SIZE:

9-1/4" (235.0mm)
11-13/16" (300.0mm)
1.000" round (25.40mm)
7/8" square (22.2mm)
9/16" (14.3mm)
round or square
MAX. WALL THICKNESS
(MILD STEEL):
MIN. WALL THICKNESS:
.125" (3.18mm)
.031" (.79mm)
Note: For stainless steel tube punching applica-
tions contact UniPunch Quotations Department
MIN. DIE CLEARANCE:
.012" (.30mm)
.4375" (11.1mm)
TO ORDER, SPECIFY:
1" 7"
1-7/8"
• Size of Tube 1
• Hole Diameter
2"
• Wall Thickness 2A 50.8mm 9/16"
• Type of Material
2
3"
Note: Because there is no 17611
ROUND PUNCH
die to support the tube at OF HOLD DOWN BOLT
17116
the site of the hole, tubes SHAPED PUNCH
distort when punching.

on punch size, tube O.D.,
wall thickness, and material 8
type. 3
9 12
KITS AND SHIMS 9-3/8"

4 SHUT
HEIGHT
Key kit: 9414
To produce shaped holes in

the model TP-2 unit (eg.
obround, square) contact the 17630
ROUND GUIDE
6
UniPunch Sales Department. 17635 3"
SHAPED GUIDE
DIE
HEIGHT
Note: Bottom hole in tube 17621

will not be distorted due to 7 ROUND DIE
die support. 17226

SHAPED DIE 10 11
1-1/2"
38.1mm

UP TO 1.000" O. D. UP TO .875" SQ.

Complete Unit 17600 17700
TP SERIES

1 Punch Head 17671 17671
2 Round Punch 17611 17611
2A Round Punch with Head 17610 17610
3 Stripping Spring 17640 17640
4 Punch Retainer Pin 2180L 2180
5 Lifter Spring 17670 17670
6 Guide (Specify Tube O.D.) 17630 17730
7 Die (Specify Tube O.D.) 17621 17721
8 B.H.S.C.S. 91130 91130
9 Guide Retainer 1018 1018
10 Pilot Pin (Round) 1120 1120
11 Pilot Pin (Diamond) 1101 1101
12 Holder 17650 17650
UNIPUNCH PPh:
H: (800)
800.828.7061 • 716.825.7960
828-7061 • (715) • FAX
263-3900 • Email: : 716.825.0581• •Web:
www.unipunch.com

Mandrel
Dimple-free Holes
Aluminum - Steel - Copper or Brass
Tube
Punching
UniPunch provides custom mandrel style hole punching units for dimple-free
holes in tube or pipe. Mandrel punching units are offered for producing round
or shaped holes in single or multiple hole configurations in round, square or
rectangle tubing or pipe. Due to the style variations, shut heights and die
heights are determined by individual mandrel unit designs.
TP-2M The photos below are examples of additional UniPunch designs that use
This mandrel tube punching unit mandrels in the tube for dimple free hole. For a prompt quotation, please send
will pierce holes 180º apart with us a detailed drawing or sketch including tube or pipe size, hole size and hole
each press stroke. location.
C-Frame Design AE Design

The tube mandrel is mounted into a steel block for single or These mandrel units are designed for producing holes near
TP SERIES
multiple hole patterns. Standard UniPunch C-Frame units are the ends of tube or pipe. Interchangeable mandrels are
used for producing round or shaped holes. available for different tube or hole sizes.
TP-2 Long Mandrel HZ Design

The 8” throat unit allows holes This mandrel system will produce
to be pierced at a greater dimple-free holes 180º apart with
distance from the tube end. each press stroke. UniPunch
horizontal units are used for
producing round or shaped holes.

77
TP-2M
OPERATING SHUT HEIGHT: 9-3/8" (238.1mm) MAX. WALL THICKNESS
UNIT OPEN HEIGHT: 11-13/16" (300.0mm) MIN. DIE CLEARANCE: .012" (.30mm)
MAX. TUBE SIZE: 1.000" round (25.40mm)
7/8" square (22.2mm)
TO ORDER, SPECIFY:
• Size of Tube COMPLETE UNIT COMMON DIMENSIONS

• Hole Diameter Part Throat Shipping
• Wall Thickness No. Depth Weight
• Type of Material 17600M 8" 20 lbs.
• Hole Location
17671
PUNCH HEAD
17611
ROUND PUNCH
17610
ROUND PUNCH
WITH HEAD
17640
STRIPPING SPRING
91130 B.H.S.C.S.
1018 GUIDE RETAINER
2180L
RETAINER CLIP
17632
GUIDE
17670
LIFTER SPRING
17625
MANDREL
ASSEMBLY
17627
PEDESTAL DIE
1120 3/8” DIA. 1101 3/8” DIA.

PILOT PIN DIAMOND PILOT PIN
Note: Various throat depths are available. Contact the UniPunch Sales Department with
tube specifications and hole location.
TP SERIES

78
TP-AE
MIN. SHUT HEIGHT: 10-1/4" 260.3mm)
UNIT OPEN HEIGHT: 11" (279.4mm)
DIE HEIGHT: 5-1/2" (139.7mm)
MIN. DIE CLEARANCE: .006" ( .15mm)
COMPLETE ROUND UNITS COMPLETE SHAPED UNITS COMMON DIMENSIONS

Part Part Throat Shipping
No. No. Depth Weight
2090M 2095M 1" 14 lbs.
2371
PUNCH HEAD
2311
ROUND PUNCH
2310
ROUND PUNCH
WITH HEAD
2315
SHAPED PUNCH
WITH HEAD
91130
B.H.S.C.S.
2340 1018
STRIPPING GUIDE RETAINER
SPRING
This semi-standard unit is

2180
RETAINER CLIP designed to punch a
single hole located up to
1” from the end of a tube.
2330
ROUND GUIDE
2335
SHAPED GUIDE
2370
LIFTER SPRING
TP SERIES
2090M-2
ROUND MANDREL DIE
2095M-2
SHAPED MANDREL DIE
1001 1101
3/8” DIA. 3/8” DIA.
PILOT PIN DIAMOND PILOT PIN
Note: Mandrel dies are custom made to your tube specifications.

Please provide drawing showing the hole size and location on the tube.

79
HZ Series Lineup
The “HZ” units are designed for horizontal punching of holes in
the vertical sides of flanges, rims and formed parts. In operation,
the press ram depresses the vertical plunger forcing the punch
horizontally through the material. On the upstroke of the ram, the
stripping spring removes the punch from the work piece.
• Four available models: 3/4”, 1 1/4”, 1 1/2” and 2”

• HZ-3/4 holder provides closest center-to-center holes
• Material Thickness: Up to 1/4” mild steel
(HZ-3/4 maximum material capacity is 3/32” mild steel)
HZ- / 3 "
OPERATING SHUT HT.: 4-3/8" (111.1mm) MIN. DIE CLEARANCE: .006" ( .15mm)
MIN. SHUT HEIGHT: 4-1/4" (107.9mm) MAX. PUNCH DIAMETER:* .2500" (6.35mm)
UNIT OPEN HEIGHT:
MATERIAL FEED CLEARANCE:
4-7/8" (123.8mm)
1/8" (3.2mm)
.0937" (2.38mm)
4
(MILD STEEL): 3/32" (2.4mm) (STAINLESS STEEL):
*For punch sizes greater than .2500” contact the
1/16" (1.6mm)
19mm width
UniPunch sales department.
COMPLETE ROUND UNITS Series HZ - Horizontal

Model No. Part No. Shipping Weight Hole Punching Units
HZ- 3⁄4 10500 3.5 lbs.
To order a unit less punch and die, add the suffix “- LPD”.
HZ-3/4 Unit for Round Holes Only 3
10
6A
1 2 3 4 5 6 7 8 9
4-3/8"
91501
11 HEX NUT
15/16"
1/8"
91341
HALF DOG
SCREW
5/16"
4-3/8"
13/16" SHUT HEIGHT
1-11/16" 3/8" HOLD
DIE HEIGHT DOWN HOLES
HZ SERIES
1100 91343
5/16" PILOT PIN HALF DOG SCREW
9/16" 91330
1" 6-1/8" SET SCREW
Item Part Item Part

No. Description No. Description
No. No.
1 Adjustment Screw 10522 8 Punch Screw FHSCS 91205

2 Round Die 10520 9 Wedge 10573
3 Lifter Spring 4273 10 Plunger 10572
4 Guide (Round) 10530 11 Holder 10550
5 Stripping Spring 3640 Hardware Kit: 9380
KITS
6 Punch Only 3211 & Punch Shim: N.A.
6A Punch w/ Head 10510 SHIMS See next page for additional
Die Shim: N.A.
horizontal hole punching units
7 Punch Head 10571 and specifications.
UNIPUNCH
PPh:
H: (800)
800.828.7061 • 716.825.7960
828-7061 • (715) • FAX
263-3900 • Email: : 716.825.0581• •Web:
www.unipunch.com

HZ
MIN. SHUT HEIGHT: 7-1/16" (179.4mm) MAX. MATERIAL THICKNESS
1-1/4" (31.8mm) MATERIAL FEED CLEARANCE: 3/8" (9.5mm) (STAINLESS STEEL): 3/32" (2.4mm)
1-1/2" (38mm)
2" (50.8mm)
COMPLETE ROUND UNITS 10
Model Part Max. Min.

No. No. Punch Punch 9
Dia. Dia.
1 .4375 .0937 2A
HZ-1 ⁄ 4 10000 11.11 mm 2.38 mm
1 2 3 4 4A 5 6 6A 6B 7 8 16
1
HZ-1 ⁄ 2 10100 .6250 .1250
15.87 mm 3.18 mm
HZ-2 10200 .8750 .1875
22.22 mm 4.76 mm
To order a unit less punch and die,

add the suffix “- LPD”.
11
7" 12
15
COMPLETE SHAPED UNITS 3/8"
14
Model Part Max. Min.

Shaped
No. No. Square Dim. A 13
7-1/2"
1 .309 .0937 SHUT
SHZ-1 ⁄4 10005 7.85 mm 2.38 mm 1-9/16" HEIGHT
4"
SHZ-11⁄ 2 10105 .441 .0937 DIE
11.20 mm 2.38 mm HEIGHT
SHZ-2 10205 .618 .1250
15.69 mm 3.17 mm
2-5/8" 6" 5/8"
11-3/8" HOLD
To order a shaped unit with round DOWN
1001 / $3.50 1101 / $5.00
punch & die, add the suffix “- RPD”. 3/8" ROUND PILOT PIN 3/8" DIAMOND PILOT PIN HOLES
COMMON DIMENSIONS HZ-11/4" HZ-11/2" HZ-2"
Holder Shipping Item Part Part Part

A Description
Width Weight No. No. No. No.
11⁄4" 9⁄16" 22.5 lbs. 1 Adjustment Screw 10022 10122 10222
11⁄ 2" 11⁄16" 28 lbs. 2 Round Die 2120 2220 2320-2

7⁄ 8" 2A Shaped Die 2125 2225 2325-2
2" 40 lbs.
3 Lifter Spring 2170 2270 2370
4 Round Guide 2130 2230 2330
4A Shaped Guide 2135 2235 2335
5 Stripping Spring 2140 2240 2340
6 Round Punch 2111 2211 2311
PRODUCT
6A Round Punch with Head 2110 2210 2310

HZ. SERIES
6B Shaped Punch with Head 2115 2215 2315

7 Punch Head 2171 2271 2371
ADDL
8 Wedge 10073 10173 10273

9 Plunger 10072 10172 10172
10 Adapter (to adjust height to 8-3/8") 10074 10074 10074
11 Holder 10055 10155 10255
12 Guide Pin 10041 10041 10041
13 Plunger Spring 10070 10070 10070
14 S.H.C.S. 91057 91057 91059
PH: (800) 828-7061 15 B.H.S.C.S. 91153 91153 91153

(715) 263-3900 16 Roll Pin 91676 91677 91677
EMAIL: [email protected]
WEB: www.unipunch.com Shaped Hole Conversion Kit 7145 7146 7147
KITS Key Kit: 9320 9320 9321
& Hardware Kit: 9381 9382 9383
SHIMS Punch Shim: N.A. N.A. N.A.
UNIPUNCH PH: 800.828.7061 • • FAX: 716.825.0581

Die Shim: 716.825.7960 N.A.
•
N.A. www.unipunch.com
N.A.

82 / The Hole Thing
Fitted
Strippers
Fitted End Stripping Guide Options Use fitted strippers for
applications requiring
minimum sheet distortion in
light gauge material and/or
applications with multiple
A SERIES FITTED END STRIPPING GUIDES holes or irregular shapes.
90 DEGREE
POSITION
REWORKED
GUIDE
REWORKED
GUIDE
B.H.C.S.
REF. BRAZED 0 DEGREE #6-32
IN TIP. FRONT OF UNIT
PUNCH SHAPE CLIP # 1471
CANNOT BE
ROTATED.
SNAP ON STRIPPER PLATE
Unit Guide Part No. Unit Guide Part No. Stripper Plate Part No.
A-1, A-1¼ Round 2131 A-2½ Round 2487
2465
AJ-1, AJ-1¼ Shaped 2138 AJ-2½ Shaped 2488
A-1½ Round 2231 Round 9548
A-3½ 2975
AJ-1½ Shaped 2238 Shaped 9558
A-2 Round 2331 Round 2882
A-5½ 2885
AJ-2 Shaped 2338 Shaped 2883
Note: Shapes will be supplied as shown Round 1482

A-8 1485
in 90 degree position unless ordered Shaped 1483
otherwise.
B SERIES FITTED END STRIPPING GUIDES
Guide Stripper Guide Stripper
REWORKED
Unit Part No. Button Unit
GUIDE
Part No. Plate
BX-¾ Round only 3035 N/A Round 3683
B3 3665
B.H.C.S.
B-1 Round only 3234 N/A Shaped 3682
#6-32 Round 3323 3332 Round Use 3883
B-1¼ B-5 standard
3881
Shaped 3324 3339F Shaped 3882
ADDL. PRODUCT
guide
CLIP #1471
Round 3423 3432
B-1¾
SNAP ON STRIPPER PLATE

Shaped 3427 3439F
Round 3523 3532
BX-2¼
Shaped 3524 3539F
Optional Inexpensive Nylon Strippers For B Series Units

These low-cost nylon strippers are furnished blank and press fit into
bottom of stripping guide as shown. At first hit of the press, the punch
pierces the blank stripper exactly to size. They are great for
punching prepainted material without marking. Punch tips
must be at least 1⁄ 16" (1.6mm) under the punch body size to use strippers.
For Unit Part No.
B-11⁄ 4 3377
B-13⁄ 4 3477
BX-21⁄ 4 3577 NYLON STRIPPER

83
Shims
& Tonnage
Reduction
Shims Extend Life of Punches and Dies Up To 4 Times
Why throw away your
punches and dies after
a few sharpenings? 1⁄ 16"
(1.6mm) thick shims are
available to restore them
to original length. “B”
Series punches and dies
are shimmed as shown
in drawings.
PUNCH SHIMS DIE SHIMS

Part Part
Unit No. Unit
No.
1081 TP-1 1/4, TP-2 3/8, B-1¾ 1091 A-1, A-1¼, B-1¼, B-1¾
1089 BX ¾ 1092 A-1½
1109 A-2½, A-3½, A-5½, AH 3½, AHD-3½ 1093 A2

AH-6, OA-6 (2¼"dia.& under)
3709 AH-3, AHD-3
Compensator Caps for “A” and “AJ” Units (1, 11⁄ 4, 11⁄ 2, 2)
For gang punching with A and AJ Part
ADDL. PRODUCT
Unit Widths A B Number

“A” or “AJ” Series Units,
Compensator Caps are 1 and-11⁄ 4 11⁄ 2 11⁄ 32 1040
fastened to the punch 11⁄ 2 13⁄ 4 19⁄ 32 1041
heads to reduce the total 2 2 117⁄ 32 1042
punching force. These
caps stagger the punch
PRESS RAM
length so the punches
contact the work piece at
different intervals, thus 1/8
reducing the total tonnage
required.
B
A
1/8
1/8
UNIPUNCH
84
Upper
UniPunch now offers upper arm components as single kits for the many
“A”, “AJ” and “B” Series holders. You can avoid costly down time by
having these kits readily available for immediate installation when required.
Arm Kits
Upper Arm Kits - “A”, “AJ” Series Upper Arm Kits - “B” Series
A-1 / AJ-1 ROUND A-1 / AJ-1 SHAPED BX-3/4 ROUND
KIT NO. 9731 KIT NO. 9732 KIT NO. 9761
2045 Stripper Spring 2045 Stripper Spring 3033 Stripper Bolt (2)
2180 Retainer Clip 2180 Retainer Clip 3032 Retainer Plate
2030 Round Guide 2035 Shaped Guide 3040 Stripper Spring
2070 Lifter Spring 2070 Lifter Spring 3030 Round Guide
4273 Lifter Spring
A-1 1/4 / AJ-1 1/4 ROUND A-1 1/4 / AJ-1 1/4 SHAPED
B-1 1/4 ROUND B-1 1/4 SHAPED
KIT NO. 9733 KIT NO. 9734
2140 Stripper Spring 2140 Stripper Spring KIT NO. 9763 KIT NO. 9764
2180 Retainer Clip 2180 Retainer Clip 3372 Punch Retainer 3372 Punch Retainer
2130 Round Guide 2135 Shaped Guide 3370 Lifter Spring 3370 Lifter Spring
2170 Lifter Spring 2170 Lifter Spring 3330 Round Guide 3335 Round Guide
A-1 1/2 / AJ-1 1/2 ROUND A-1 1/2 / AJ-1 1/2 SHAPED B-1 3/4 ROUND B-1 3/4 SHAPED
KIT NO. 9735 KIT NO. 9736 KIT NO. 9765 KIT NO. 9766
2240 Stripper Spring 2240 Stripper Spring 3472 Punch Retainer 3472 Punch Retainer
2180 Retainer Clip 2180 Retainer Clip 2370 Lifter Spring 2370 Lifter Spring
2230 Round Guide 2235 Shaped Guide 3430 Round Guide 3435 Shaped Guide
2270 Lifter Spring 2270 Lifter Spring
BX-2 1/4 ROUND BX-2 1/4 SHAPED
ADDL. PRODUCT
A-2 / AJ-2 ROUND A-2 / AJ-2 SHAPED
3572 Punch Retainer 3572 Punch Retainer
2340 Stripper Spring 2340 Stripper Spring
2180 Retainer Clip 2180 Retainer Clip
3530 Round Guide 3536 Shaped Guide
“A” & “AJ” SERIES “B” SERIES
A-2 1/2 / AJ-2 1/2 ROUND A-2 1/2 / AJ-2 1/2 SHAPED
2485 Punch Screw 2485 Punch Screw

2440-10 Stripper Spring 2440-10 Stripper Spring
2433 Retainer Ring 2433 Retainer Ring
Kit No. 9736 shown Kit No. 9768 shown
85
For “A”, “AJ”, “FTA”, “HZ”, and “AE” Units
Stock Punch • Available for immediate shipment
Sizes • Round punch sizes from 3/32” to 7/8”
2111 Round Punch 2211 Punch

2010 Round Punch w/head 2210 Punch w/head
2011 Round Punch w/head Fractional Inch Decimal Inch Metric (mm)
Fractional Inch Decimal Inch Metric (mm) 11/64 .1718 4.366
1/8 .1250 3.175 3/16 .1875 4.762
5/32 .1562 3.969 13/64 .2031 5.159
3/16 .1875 4.762 7/32 .2187 5.556
- .1960 4.978 1/4 .2500 6.350
13/64 .2031 5.159 - .2570 6.527
7/32 .2187 5.556 17/64 .2656 6.747
1/4 .2500 6.350 - .2700 6.858
- .2570 6.527 9/32 .2812 7.144
- .2600 6.604 5/16 .3125 7.938
17/64 .2656 6.747 11/32 .3437 8.731
9/32 .2812 7.144 3/8 .3750 9.525
5/16 .3125 7.938 25/64 .3906 9.525
11/32 .3437 8.731 13/32 .4062 10.319
3/8 .3750 9.525 7/16 .4375 11.112
25/64 .3906 9.525 1/2 .5000 12.700
13/32 .4062 10.319 17/32 .5312 13.494
7/16 .4375 11.112 9/16 .5625 14.288
5/8 .6250 15.875
2311 Punch
UniPunch provides immediate shipment
ADDL. PRODUCT
2310 Punch w/head

on common punch diameters.
Fractional Inch Decimal Inch Metric (mm)
5/16 .3125 7.938
3/8 .3750 9.525
13/32 .4062 10.319
7/16 .4375 11.112
1/2 .5000 12.700
17/32 .5312 13.494
9/16 .5625 14.288
5/8 .6250 15.875
11/16 .6875 14.462
3/4 .7500 19.050
13/16 .8125 20.638
UNIPUNCH
86
Custom Designed and manufactured for applications in…
• Angles - Channels - Aluminum Extrusion
Units • Roll Formed or Brake Formed Parts
• Irregular Shaped or Molded Parts
In cases where standard UniPunch modular units cannot produce the necessary results for your specific application, our experience
in die design and the manufacture of custom units can provide successful solutions for your punching or notching requirements.
Examples would be holes close to the leg of an angle, channel or an aluminum extrusion or irregular notching and punching
configurations.
Begin by sending us your detailed part drawing or sample part. For holes in specific locations in aluminum extrusions, a profile
drawing is required. Our engineering team will review your part application and promptly quote tooling to meet your needs.
The photos below are examples showing custom units that UniPunch can provide.
Tandem Units
Ordinarily the holder width defines the minimum hole centers.
Shown here are custom tandem units designed for specific
applications that use standard upper arm components to punch
multiple rows of holes in a single stroke.
Block Die Units

For applications where holes are required near
the legs of angles or extrusions, UniPunch can
provide block style dies in “A” or “AH”- Series
units. Upon request, the block die can also
provide the required front to back part gauging. Standard “A”- Series UniPunch unit modified to
accept block die for punching aluminum extrusions.
Custom Notching Units Custom Die Sets

For part notching applications in unique custom For applications that include holes, notches or other
extrusions, UniPunch can design and build tooling features outside the capabilities of standard UniPunch
for your application. Custom corner notch, edge units, UniPunch will build compatible custom die sets
notch or combination notch and punch units are with the shut height and die height to work alongside the
available. standard “A” or “B” Series units used in the application.
Custom corner notching
UniPunch Gib Style notching units

88
Tool
Maintenance
PROPER SET UP PRACTICE (MOUNTING INFORMATION)
• Remove all dirt from unit bottoms and mounting surfaces to insure that units are flat on the
mounting templates.
• Use proper length bolts and washers when securing units to mounting templates.
• Check unit die heights. All holders must have uniform die heights to prevent sheet distortion and
unit misalignment.
• Before starting press, be sure set-up is guarded in compliance with regulations.
• After positioning the setup in the press, adjust shut height by gradually lowering the press ram until
all punches enter their respective dies. Punches should only enter dies enough to push out slugs,
usually no more than 1/32".
• Clear slugs regularly.
OILING INFORMATION
• Apply light machine oil (SAE 10 or equivalent) to punch and guide area.
• Moly Kote® type ‘GN’ paste lubricant is applied to units shipped from factory.
• Lubricate unit components as necessary to ensure proper functioning.
REPLACE FATIGUED SPRINGS

• Check spring length. Fatigued springs usually take a ‘set’ and are visibly shorter than new springs.
• After normal use, fatigued springs may not have sufficient power to strip punches from work
piece. If punches and dies are sharp and the unit is not stripping properly, it is most likely a worn
stripping spring.
PUNCH SHARPENING
Punch and die life can be extended considerably by sharpening tools when an approximately .010”
radius is on cutting edge. The number of holes produced between sharpenings will vary according to
the material thickness and type being punched. As an example, from perhaps 500 to 1,000 holes in
heavy material to 10,000 to 15,000 holes in 16 gauge (.0598)(1.6mm) 50,000-PSI mild steel. Using
16 gauge as an example, refer to the diagram below for proper sharpening to increase punch life.
Improper sharpening Proper sharpening
.040 R. 4 SHARPENINGS
ONE SHARPENING
.010
FIRST GRIND
.010 R.
.010 R.
MAINTENANCE
.040" (1.01MM) REQUIRED TO BE WITH .010"(.040") REMOVED

REMOVED IF SHARPENING IS NEGLECTED. IN 4 SHARPENINGS.
Note: Quantity of holes will vary considerably due to material hardness, proper die clearance or
unit alignment.
GENERAL SHARPENING NOTES:

• Take light cuts when sharpening.
• Use soft coarse grinding wheel.
• Coolant should be used when sharpening cutting surfaces.
UNIPUNCH
90
Technical
Data
Required Dimensioning Specifications for common shapes
The shapes below are available for most hole punching units. When ordering, specify dimensions as shown. Refer to individual holder
specifications for size limitations. Decimal and metric sizes are available at no additional cost.
B B A B
ROUND OBROUND RECTANGLE SINGLE “D” DOUBLE “D” SQUARE
A A B B
A A
S S S
S S S
X X
S=A S=A X S = √A2 + B2 S=A X S=A X S = 1.414B
P = 3.14A P = 2A + 1.14B P = 2A + 2B P(est) = 1.57A + 2B P(est) = 2A + 2B P = 4B
A B
LONG “D” HEXAGON OCTAGON
S=Diameter, P=Perimeter
A
B A As these shapes are illustrated, point ‘X’ is at
S S S 0 degrees of angular orientation.
X X X
S = [A2/(4B)] + B S = 1.155A S = 1.082A
P = 2B + 1.57A P = 3.46A P = 8B + 3.313A
How to Specify Angular Orientation for punches and dies

Most shaped punches and dies can be used in two positions at 90 degrees to each other. Angularity is measured from 0 to 360 degrees
clockwise when viewed from the top. Zero degrees is at the front of the unit. See diagrams below.
180° X
X
90° 270°
0°
FRONT OF UNIT (TOP VIEW) FRONT OF UNIT (TOP VIEW)
On the obround shape shown in the drawing, point ‘X’ On the keyhole shape shown in this drawing, point ‘X’ is
is at 0 and 90 degrees. illustrated at 180 and 270 degrees.
Additional Examples of Orientation

When ordering any shape, specify at what angle you want point ‘X’. On most holders standard keying is at 0 and 90 degrees; other angular
settings are available upon request. Contact the UniPunch Sales Department for assistance.
A A
KEYHOLE 1200 BUTTERFLY 1201 1204 LONG “D” 1205 KEYHOLE 1206 SQUARE 45° 1209
A A
RADIUS C RADIUS
A
D B D
C C
B C C
RADIUS A DIA.
B
B B
RADIUS POINT X POINT X POINT X POINT X POINT X POINT X
A B B
EQUIL. TRIANGLE DIAMOND SQ. / DIA. CORNERS
Point ‘X’ refers to 0 degree position as operator faces front of holder.
B 60° A
A
TECH. DATA
S
X
X X

UNIPUNCH
91
Technical Data UNIPUNCH HOLES IN PARTS. FAST.
Custom Applications
Additional Shapes
Some of the special shapes we manufacture are shown below. A code number is provided for easy referencing when
ordering. A fully dimensioned sketch should accompany all orders or inquiries. For shapes not shown below, contact the
UniPunch Sales Department.
099 101 102 103 104 105 106 107 108 109
110 111 112 113 114 115 116 117 118 119
120 121 122 123 124 125 126 127 128 129
130 131 132 133 134 135 136 137 138 139
140 141 142 143 144 145 146 147 148 149
150 151 152 153 154 155 156 157 158 159
Other System Capabilities

In addition to hole punching, your product may require supplementary fabricating operations. Here are a few examples that
can be accomplished with the UniPunch System. Contact the UniPunch Sales Department with your specific requirements.
1251 Trim & Part (2 radii total) 1255 Corner Radius
Specify part C Specify radius HEEL LENGTH
width and HEEL LENGTH required. ʻAʼ SERIES = .38
radius required. ʻAʼ SERIES = .38 (shown without ʻBʼ SERIES = .25
ʻBʼ SERIES = .25 heel gauging) 45˚
5˚
A 100˚
HE
HEEL
EL
MATERIAL Required Parameters Required Parameters

A = Trim Radius A = Radius
C = Run Out Angle (5° to 10° Default) RADIUS MATERIAL Material Type & Thickness (10 Ga. Max.)
Material Type & Thickness (10 Ga. Max.)
Cluster Required Parameters Vee Notch Required Parameters

Allows multiple Hole sizes Depth of Notch
hole patterns Hole centers Angle of Notch
in one hit Shaped Holes - Specify type of shape Material Thickness
Material Thickness
Lance and Form Required Parameters Emboss Required Parameters
Form down Length Form down A Diameter
Width A = Angle
Depth Overall Height
Material Thickness Material Thickness
Heeled Punches
Recommended for notching the edge of the sheet metal. The heel of the punch engages into the die to stabilize the punch. When
ordering, specify either obround or rectangle shape. Two variations of each are available as shown below.
1/4" MIN.
HEELED OBR. 1230 OBR. END & HEEL 1231 HEELED RECT. 1235 RECT. END & HEEL 1236
1/4"MIN. 1/4"MIN. 1/4"MIN.

BODY BODY
RADIUS RADIUS
TECH. DATA
H MAX. FOR
B MAX. PUNCH
1/4"MIN. B “A” DIM.
1/4" MIN. BODY DIA.
B WITHIN BODY
H A A
A A
POINT X POINT X
POINT X POINT X
“A” SERIES H= 3/8"
“B” SERIES H=1/4" Note: Use edge notch units for heavy material applications or when notch is beyond the range of Heeled
Punches.
For additional information on custom applications, visit the UniPunch website at

92 www.unipunch.com/SystemCapabilities
Technical
Data
Forming Tools
Countersinking Holes for Flat Head Screws
STYLE 1 A 1261 Countersink (style 1)
Countersink punches with standard open die buttons as illustrated to the
D - DIA. AT TOP SURFACE - TO
left are used in “A” or “B” Series units for countersinking up to 10 gauge INTERSECTING POINTS
mild steel to accept flat head screws. Die buttons have a .02” radius
instead of cutting edge. “A” Series units with adjustable feed opening are T B C
recommended for easy removal of formed workpiece. The “B” unit feed A = Angle D = Screw/Rivet Size (dia.)
B = Clearance Hole T = Thickness
C = Overall Ht. (incl. material)
clearance must be increased for removal of formed workpiece.*
STYLE 2 A 1262 Countersink (style 2)

The die shown at left allows the punch to bottom the countersink shape D - DIA. AT TOP SURFACE - TO
into the workpiece at the bottom of stroke. This die provides a more INTERSECTING POINTS
uniform countersink.*
T B C
A = Angle D = Screw/Rivet Size (dia.)
B = Clearance Hole T = Thickness
C = Overall Ht. (incl. material)
STYLE 3 A
1263 Countersink (style 3)
The machined type of countersink is used in “A” or “B” Series
standard units for countersinking up to 10 gauge material. The die T
D
shown at the left allows the punch and die to bottom the countersink
shape into the workpiece at the bottom of the stroke.*
A = Angle
D = Screw/Rivet Size (dia.)
Due to the nature of this style, material will deform and a burr will occur.
T = Thickness
The amount will vary according to material and specifications.
*Note: All of the above mentioned Countersinking Punches and Dies are bottoming operations and extreme caution must be taken in setting the proper shut
height. Prices are available upon request from the UniPunch Sales Department. Specify size of screw, type of material and thickness when inquiring.
Extrusion Punches and Dies

Special punches with oversize die buttons are used in standard “A” or “B” Series units to
produce extruded holes to accept sheet metal screw or permit tapping in thicker material for
R.02” Extruding Dia.
When machine screws. Die buttons have .02” radius instead of cutting edge. “A” Series units with
inquiring
specify type
Die Opening adjustable feed opening are recommended for easy removal of formed workpiece. The “B” unit
and thickness Piercing Dia. feed clearance must be increased for removal of formed workpiece. Prices are available upon
of material
and screw size Developed to
request from the UniPunch Sales Department.
Screw Size
“A” & “B” Series Knockout Units

SINGLE
KNOCKOUT
Two tabs furnished unless
TABLE OF PUNCH SIZES
otherwise specified. FOR STANDARD CONDUIT
PUNCH STD. HOLDER
Tab position Punch and die are shaped for positive
if single tab alignment of tabs and can be rotated 90°.
Conduit Punch Size
ordered Size (I.D.) of Slip Hole
3⁄ 8 11⁄ 16
FRONT OF UNIT STRIPPER
1⁄ 2 7⁄ 8 SPRING
DIE
Standard units with modified punches and dies are used for 3⁄ 4 11⁄ 8
forming single electrical knockouts. The dies have built-in strippers
1 13⁄ 8
to force slug out of die for easy removal from unit. Maximum
capacity 1/16” mild steel. When ordering, specify actual hole 11⁄ 4 13⁄ 4
STRIPPER
diameter, thickness of material and number of tabs (one or two). 11⁄ 2 2 ASSEMBLY
TECH. DATA
2 21⁄ 2
DOUBLE Double Knockout Units are made according to 21⁄ 2 3
KNOCKOUT
customer’s specifications. When ordering, 5⁄ 8
specify actual hole diameter, thickness of 3 3
material, number and locations of tabs. Prices PIERCED HOLE DIAMETER
available
PH: 800.828.7061 upon request. • FAX: 716.825.0581 • www.unipunch.com
• 716.825.7960 (CLEARS O.D. OF CONDUIT)
93
Technical Hole Dia. 20 GA. 18 GA.
Approximate Tonnage Required
for Punching Round Holes in Mild Steel (50,000 psi shear strength)
16 GA. 14 GA. 12 GA. 11 GA. 10 GA. 3/16 1/4 5/16 3/8 1/2
Data in Inches .036

1/8
3/16
1/4
.35
.53
.71
.048
.47
.71
.94
.060
.59
.89
1.2
.075
.74
1.1
1.5
.105
1.0
1.6
2.1
.120
1.2
1.8
2.4
.135
—
2.0
2.7
.187
—
2.8
3.7
.250
—
—
4.9
.312
—
—
—
.375
—
—
—
.500
—
—
—
Calculating Tonnage 5/16

3/8
.88
1.1
1.2
1.4
1.5
1.8
1.9
2.2
2.6
3.1
3.0
3.5
3.3
4.0
4.6
5.5
6.2
7.4
7.8
9.2
—
11.1
—
—
7/16 1.2 1.7 2.1 2.6 3.6 4.1 4.6 6.5 8.6 10.8 13.0 17.2
1/2 1.4 1.9 2.4 2.9 4.1 4.7 5.3 7.4 9.8 12.3 14.8 19.7
How to Obtain 9/16 1.6 2.1 2.7 3.3 4.7 5.3 6.0 8.3 11.0 13.8 16.6 22.1
5/8 1.8 2.4 2.9 3.7 5.2 5.9 6.6 9.2 12.3 15.4 18.5 24.6
Tonnage Required for 11/16 1.9 2.6 3.2 4.1 5.7 6.5 7.3 10.2 13.5 16.9 20.3 27.1
Punching Round Holes: 3/4 2.1 2.8 3.5 4.4 6.2 7.1 8.0 11.1 14.8 18.4 22.1 29.5
13/16 2.3 3.1 3.8 4.8 6.7 7.7 8.6 12.0 16.0 20.0 24.0 32.0
2.000" 7/8 2.5 3.3 4.1 5.2 7.2 8.3 9.3 12.9 17.2 21.5 25.8 34.4
DIA. HOLE 15/16 2.7 3.5 4.4 5.5 7.7 8.8 10.0 13.8 18.5 23.0 27.7 36.9
1 2.8 3.8 4.7 5.9 8.3 9.4 10.6 14.8 19.7 24.6 29.5 39.4
1-1/2 4.2 5.6 7.0 8.8 12.3 14.1 15.8 22.1 29.5 36.8 44.2 58.9
2 5.6 7.5 9.4 11.7 16.4 18.8 21.1 29.5 39.3 49.1 58.9 78.5
2-1/2 7.1 9.4 11.7 14.7 20.5 23.6 26.4 36.8 49.1 61.4 73.6 98.2
3 8.5 11.3 14.1 17.6 24.6 28.2 31.7 44.2 58.9 73.6 88.4 118
3-1/2 9.9 13.1 16.4 20.5 28.8 32.7 37.0 51.5 68.7 85.9 103 137
4 11.3 15.0 18.8 23.5 32.8 37.6 42.2 58.9 78.5 98.2 118 157
4-1/2 12.7 16.9 21.2 26.4 37.0 42.4 47.5 66.3 88.4 110 133 177
1/4 (.250")
5 14.1 18.7 23.5 29.3 41.1 47.1 52.8 73.6 98.2 123 147 196
THICK M.S.
To obtain tonnage required for punching round holes in mild steel multiply as follows:
FORMULA: 3.1416 x Diameter of Hole x Material Thickness x 25 = Punching Tonnage Required for One Hole
TONNAGE IN MILD STEEL =
3.1416 x DIA. OF HOLE x Note: Additional tonnage is required to compress UniPunch units during the press down stroke.
MAT’L THICKNESS x 25 Contact the UniPunch Sales Department for stripping spring compression ratings for individual units.
EXAMPLE:
3.1416 x 2.000 x.250 x 25
ANSWER: Approximate Tonnage Required for Notching
39.26 TONS Gauge 20 18 16 14 12 10 3/16” 1/4” 3/8” 1/2”
Metal Thickness
Decimal .036 .048 .060 .075 .105 .135 .187 .250 .375 .500
Tons Required to Notch 1” Length .99 1.30 1.65 2.05 2.85 3.65 5.01 6.60 9.55 12.5
VISIT
www.unipunch.com/TechSupport To obtain tonnage required for notching mild steel multiply as follows:
for our online Tonnage Calculator Total shear length x material thickness x 25 = tonnage required for total length of shear
How to Obtain Multiplier Chart for Various Materials

Tonnage Required for Above chart shows tonnage for punching holes in mild steel (50,000 psi).
For punching materials of different shear strength, use multiplier in chart below.
Punching Shaped Holes:
Material Tons Per Yield or Shear
Description Sq. In. Strength Per Sq. In. Multiplier
2.000"
SQUARE HOLE Aluminum — Soft Sheet 7-1/2 15,000 psi .30
Aluminum — Half Hard 9-1/2 19,000 psi .38
Aluminum — Hard 12 25,000 psi .50
Brass — Soft Sheet 15 30,000 psi .60
Brass — Half Hard 17-1/2 35,000 psi .70
Copper — Rolled 14 28,000 psi .56
Steel — Mild 25 50,000 psi 1.00
Steel — ASTM - A36 30 60,000 psi 1.20
Steel — 50 Carbon 35 70,000 psi 1.40
1/4 (.250")
Steel — Cold Drawn 30 60,000 psi 1.20
THICK M.S.
Steel — Stainless (18 - 8) 35 70,000 psi 1.40
FORMULA:
TONNAGE IN MILD STEEL =
PERIPHERY x MATERIAL Effect of Punch Shear on Tonnage
THICKNESS x 25 The chart at top shows tonnage for flat ground punches (without shear).
Chisel shear on punches can considerably reduce required press tonnage.
TECH. DATA
EXAMPLE:
The chart below shows tonnage reduction factors for the shear depths listed.
(2 + 2 + 2 + 2) x .250 x 25
ANSWER:
Multiply shear factor times actual tonnage to obtain reduced tonnage per hole.
50 TONS Shear Depth Up to 16 GA. 14 GA. 12 GA. 10 GA. 8 GA. 3/16 GA. 1/4 GA.
1/16 .50 .60 .75 .80 .85 .87 .90
UNIPUNCH
3/32 .50 .50 .60 .70 .75 .80 .85
3/16 .50 .50 .50 .50 .50 .50 .65

Technical
Data
Twist Drills
Letter and Number Sizes
Letter Drill Number Drill Number Drill Number Drill
Sizes Diameter Sizes Diameter Sizes Diameter Sizes Diameter
Inch Inch Inch Inch
Z 0.413 1 0.2280 28 0.1405 55 0.0520
Y 0.404 2 0.2210 29 0.1360 56 0.0465
X 0.397 3 0.2130 30 0.1285 57 0.0430
W 0.386 4 0.2090 31 0.1200 58 0.0420
V 0.377 5 0.2055 32 0.1160 59 0.0410
U 0.368 6 0.2040 33 0.1130 60 0.0400
T 0.358 7 0.2010 34 0.1110 61 0.0390
S 0.348 8 0.1990 35 0.1100 62 0.0380
R 0.339 9 0.1960 36 0.1065 63 0.0370
Q 0.332 10 0.1935 37 0.1040 64 0.0360
P 0.323 11 0.1910 38 0.1015 65 0.0350
O 0.316 12 0.1890 39 0.0995 66 0.0330
N 0.302 13 0.1850 40 0.0980 67 0.0320
M 0.295 14 0.1820 41 0.0960 68 0.0310
L 0.290 15 0.1800 42 0.0935 69 0.0292
K 0.281 16 0.1770 43 0.0890 70 0.0280
J 0.277 17 0.1730 44 0.0860 71 0.0260
I 0.272 18 0.1695 45 0.0820 72 0.0250
H 0.266 19 0.1660 46 0.0810 73 0.0240
G 0.261 20 0.1610 47 0.0785 74 0.0225
F 0.257 21 0.1590 48 0.0760 75 0.0210
E 0.250 22 0.1570 49 0.0730 76 0.0200
D 0.246 23 0.1540 50 0.0700 77 0.0180
C 0.242 24 0.1520 51 0.0670 78 0.0160
B 0.238 25 0.1495 52 0.0635 79 0.0145
A 0.234 26 0.1470 53 0.0595 80 0.0135
27 0.1440 54 0.0550
Bend Allowance
Unless otherwise specified, the following bend allowances are used
to calculate flat pattern developments for mounting template layouts: TOTAL LENGTH =
A + B + BEND ALLOWANCE
GAUGE DECIMAL ALLOWANCE .1° ALLOWANCE .90° RADIUS** T
24 .024 .00042 .038 .016
22 .030 .00045 .041 .016 R B
20 .036 .00048 .044 .016
18 .048 .00055 .050 .016
BEND
16 .060 .00062 .056 .016 ALLOWANCE
14 .075 .00097 .087 .031 A
12 .105 .00115 .103 .031
1/8 .125 .00180 .163 .062
10 .135 .00186 .168 .062
T B
8 .164 .00203 .183 .062
3/16 .187 .00318 .286 .12 R
.229 .229 .00342 .308 .12
TECH. DATA
BEND
1/4 .250 .00354 .319 .12 ALLOWANCE
5/16 .312 .00495 .446 .18
3/8 .375 .00532 .479 .18 A
**Use standard radius when no radius is specified on blueprint. When radius or thickness differs from chart, the
following formulas will be used: B.A. for 1° = ((T/3) + R) .01745 • B.A. for 90° = ((T/3) + R) 1.5708
UNIPUNCH
T= Material Thickness, R=Bend Radius
When radius is greater than twice metal thickness, substitute T/2 in above formulas.

Technical CONVERTING TO METRIC
Data TO CONVERT INCHES INTO MILLIMETERS, THE FOLLOWING FORMULA MAY BE USED:
Decimal size (inches) x 25.4 = metric equivalent.
TO CONVERT MILLIMETERS INTO INCHES, THE FOLLOWING FORMULA MAY BE USED:
Decimal Equivalents Metric size (millimeters) ÷ 25.4 = decimal equivalent.
Decimal Millimeter Decimal Millimeter

1 33
64 0.015625 0.397 64 .515625 13.097
1 17
32 .03125 0.794 32 .53125 13.494
3 35
64 .046875 1.191 64 .546875 13.891
1 9
16 .0625 1.588 16 .5625 14.288
5 37
64 .078125 1.984 64 .578125 14.684
3 19
32 .09375 2.381 32 .59375 15.081
7 39
64 .109375 2.778 64 .609375 15.478
1 5
8 .1250 3.175 8 .6250 15.875
9 41
64 .140625 3.572 64 .640625 16.272
5 21
32 .15625 3.969 32 .65625 16.669
11 43
64 .171875 4.366 64 .671875 17.066
3 11
16 .1875 4.762 16 .6875 17.462
13 45
64 .203125 5.159 64 .703125 17.859
7 23
32 .21875 5.556 32 .71875 18.256
15 47
64 .234375 5.953 64 .734375 18.653
1 3
4 .2500 6.350 4 .7500 19.050
17 49
64 .26565 6.747 64 .765625 19.447
9 25
32 .28125 7.144 32 .78125 19.844
19 51
64 .296875 7.541 64 .796875 20.241
5 13
16 .3125 7.938 16 .8125 20.638
21 53
64 .328125 8.334 64 .828125 21.034
11 27
32 .34375 8.731 32 .84375 21.431
23 55
64 .359375 9.128 64 .859375 21.828
3 7
8 .3750 9.525 8 .8750 22.225
25 57
64 .390625 9.922 64 .890625 22.622
13 29
32 .40625 10.319 32 .90625 23.019
27 59
64 .421875 10.716 64 .921875 23.416
7 15
16 .4375 11.112 16 .9375 23.812
29 61
64 .453125 11.509 64 .953125 24.209
15 31
.46875 11.906 .96875 24.606
TECH. DATA
32 32
31 63
64 .484375 12.303 64 .984375 25.003
1
2 .5000 12.700 1 1.000 25.400
UNIPUNCH
96
Technical
Data
Die Clearance for UniPunch Modular Tooling
By definition, Die Clearance is the space MILD STEEL
between the cutting edge of the punch and The total die clearance of 20% of
the cutting edge of the die. Optimal die material thickness is used when
clearance is determined by the thickness and punching mild steel (50,000 psi)
type of the material being punched. Many material. This die clearance provides PUNCH & DIE CLEARANCE
studies have been made throughout the maximum punch and die life, 1) WHAT IS DIE CLEARANCE?
metalworking industry regarding the proper requires less stripping pressure and It is the dimensional difference
amount of die clearance and the results minimum press tonnage, which is an between the punch & die.
2) INDUSTRY STD. –
differ due to the many variables such as type important feature when using always total clearance
and hardness of material being punched, multiple UniPunch units in setups. 3) UNITIZED TOOLING STANDARD
type and speed of the press equipment and is usually 20% of material thick-
the design of the tooling itself. Through ALUMINUM, COPPER AND BRASS ness for 50,000 p.s.i. mild steel
continued research and experience, we have The total die clearance of 15% of
arrived at the following recommendations for material thickness is recommended PUNCH
die clearance. for low shear strength materials and MATERIAL

soft materials that tend to drag on
punches and dies.
DIE
What Die Clearances should be used? STAINLESS STEEL
Longer tool life, reduced stripping force and When punching high shear strength
materials such as stainless steel, we 1/2
good hole quality are directly related to the THE TOTAL
selection of proper die clearance. Material recommend 25% of the material CLEARANCE
characteristics such as type, thickness and thickness for die clearance. This EXAMPLE:
.060 THICK MILD STEEL
shear strength are factors that determine helps to reduce punching tonnage 1.000 DIA. PUNCH
what die clearance should be used. The and will aid in increasing tooling life. DIE CLEARANCE = .060" X 20% = .012"
DIE SIZE = 1.012
following are guidelines for punching various Visit our website at www.unipunch.com and
material types. For questions regarding your click the Tech Support tab for our online Die
specific material punching application, Clearance calculator.
contact the UniPunch Sales Department.
How Often Should Punches and Dies be Sharpened?

Punch and Die life can be extended indicates that the metal in the immediate
considerably by prudent sharpening at the vicinity is fatigued. At this time the punch
ideal time. The number of holes produced and die should be sharpened.
between sharpening will vary according to Tools not sharpened at the proper time will
the material thickness and hardness. also allow tool edges to deteriorate rapidly
Punches typically require more frequent and create extreme pressure on the cutting
sharpening than die buttons by almost two edges and will increase punching pressure
to one. requirements. This in turn will decrease
On a new or sharpened punch or die, the quality and quantity of holes produced
shearing edges are square and sharp. along with creating poor stripping conditions
These edges are rather fragile considering in the unit.
that they must withstand the impact and Therefore, frequent sharpening and minimum
tonnage required fracturing the material material removal is by far the least
being punched. After considerable punching, expensive and produces consistent high
observation of this edge will show a slight quality holes.
TECH. DATA
rounding (approximately .010"/.015" radius),

and will have a frosted appearance. This

97
Technical
Data
Material Technical Information
SPECIFICATION FOR COMMON MATERIALS AND RECOMMENDED DIE CLEARANCE
DESCRIPTION HARDNESS SHEAR STRENGTH MATERIAL RECOMMENDED DIE
PSI N / mm² MULTIPLIER CLEARANCE IN %
OF THICKNESS
Steels
Low Carbon HR Sheet Rb 70 50,000 345 1.00 20%
Low Carbon C.R. Sheet Rb 40,000 276 .80 20%
ASTM A-36 BHN 119-159 58-80,000 1.20 20-25%
45-50 Carbon HR Sheet BHN 200 80,000 552 1.60 25%
Spring Steel 1074, 1095
Hardened to Spring Temper Rc 45-50 200,000 1.380 4.0 30%
COR-TEN Steel BHN 120 55,000 379 1.1 20%
Aluminum Base Alloy(s) And Tempers(s)
1100-0 BHN 23 9,000 62 .18 15%

1100-H14 BHN 32 11,000 76 .22 18%
2024-0 BHN 47 18,000 124 .36 18%
2024-T3 BHN 120 41,000 283 .82 20%
3003-0 BHN 28 11,000 76 .76 15%
3003-H14, H16 BHN 40-47 15,000 103 .30 18%
3105-H25 BHN 47 16,000 110 .32 18%
5005-H34 BHN 41 14,000 97 .28 18%
5052-0 BHN 47 18,000 124 .36 18%
5052-H32 BHN 60 20,000 138 .40 20%
6061-0 BHN 30 12,000 83 .24 15%
6061-T6 BHN 95 30,000 207 .60 20%
7075-0 BHN 60 22,000 152 .44 20%
7075-T6 BHN 150 48,000 331 .96 20%
Copper Base Alloys & Tempers
110 Electrolitic Copper

- .050 mm GS Rb 40 22,000 152 .44 15%
- ½ Hard Rb 40 26,000 179 .52 20%
- Hard Rb 50 28,000 193 .56 25%
220 Comm Bronze 90%

- ½ Hard Rb 55 35,000 241 .70 15%
230 Red Brass 85%
- ¼ Hard Rb 55 35,000 241 .70 15%
260 Cartridge Brass
- .035 nn Gs Rb 68 34,000 234 .68 15%
- ½ Hard Rb 70 40,000 276 .80 18%
- Spring Rb 91 48,000 331 .96 20%
342 A High Lead - ½ Hard Rb 70 40,000 276 .80 18%
675 Manganese Bronze Rb 65 42,000 290 .84 18%
Stainless Steel Thickness
202 Annealed Rb 95 90,000 620 1.8 .024-.048” 15%
302,303, 304 Annealed Rb 85 75,000 517 1.5 (0.5-1.5mm)
310 Annealed Rb 90 90,000 620 1.8 .060-.120” 20%
316,321,430 Annealed Rb 90 75,000 517 1.5 (1.5-3.0mm)
410 Annealed Rb 85 75,000 517 1.5 over .120” 30%
TECH. DATA
(3.0mm)
Other
Titanium - Unalloyed Rb 23-29 50,000 345 1.20 25%
UNIPUNCH
98
Technical
Data
Optional Punch Features
METAL GAUGES IN DECIMALS OF AN INCH
Use the chart below to convert standard gauge numbers in decimals of an
inch for sheet steel, aluminum and stainless steel.
Gauge # Sheet Steel Aluminum Stainless Steel

1 — .2893 (7.3) .2812 (7.1)
2 — .2576 (6.5) .2656 (6.7)
3 .2391 (6.1) .2294 (5.8) .2500 (6.4)
Back Taper on punch tips
4 .2242 (5.7) .2043 (5.2) .2344 (6.0) helps to reduce galling and
5 .2092 (5.3) .1819 (4.6) .2187 (5.6) stripping problems when
6 .1943 (4.9) .1620 (4.1) .2031 (5.2) punching stainless steel or
7 .1793 (4.6) .1443 (3.7) .1875 (4.8) thick material.
8 .1644 (4.2) .1285 (3.3) .1719 (4.4)
9 .1495 (3.8) .1144 (2.9) .1562 (4.0)
10 .1345 (3.4) .1019 (2.6) .1406 (3.6)
11 .1196 (3.0) .0907 (2.3) .1250 (3.2)
12 .1046 (2.7) .0808 (2.1) .1094 (2.8)
13 .0897 (2.3) .0720 (1.8) .0937 (2.4)
14 .0747 (1.9) .0641 (1.6) .0781 (2.0)
15 .0673 (1.7) .0571 (1.5) .0703 (1.8)
16 .0598 (1.5) .0508 (1.3) .0625 (1.6)
17 .0538 (1.4) .0453 (1.2) .0562 (1.4) Stub Tip design is
recommended on small
18 .0478 (1.2) .0403 (1.0) .0500 (1.3)
punch sizes to help prevent
19 .0418 (1.1) .0359 (0.9) .0437 (1.1) breakage.
20 .0359 (0.9) .0320 (0.8) .0375 (1.0)
21 .0329 (0.8) .0285 (0.7) .0344 (0.9)
22 .0299 (0.8) .0253 (0.6) .0312 (0.8)
23 .0269 (0.7) .0226 (0.6) .0281 (0.7)
24 .0239 (0.6) .0201 (0.5) .0250 (0.6)
25 .0209 (0.6) .0179 (0.5) .0219 (0.6)
26 .0179 (0.5) .0159 (0.4) .0187 (0.5)
27 .0164 (0.4) .0142 (0.4) .0172 (0.4)
28 .0149 (0.4) .0126 (0.3) .0156 (0.4) Radius Corners on square
29 .0135 (0.3) .0113 (0.3) .0141 (0.3) or rectangle punches
Dimension in inches (millimeters) prevents chipping or
cracking on corners. Also
beneficial by reducing stress
TECH. DATA
to die corners.

99
Slot Sizes
& Location A, AJ, AH, OA-6 and AD Holders
A, AH Holder
HOLDER A B C D E F G H
3/8 DIA. PILOT PINS (REF: .376 DIA. IN TEMPLATE) 17⁄ 8 17⁄ 8
4A -1 — — 9⁄ 16 5⁄ 8 41⁄ 8 7
E SLOT WIDTH 17⁄ 8 25⁄ 8
8A-1 5⁄ 8 25⁄ 8 9⁄ 16 5⁄ 8 81⁄ 8 11
1.500 REF. 12A-1 17⁄ 8 25⁄ 8 5⁄ 8 25⁄ 8 9⁄ 16 5⁄ 8 121⁄ 8 15
4A-11⁄ 4 17⁄ 8 17⁄ 8 — — 9⁄ 16 5⁄ 8 41⁄ 8 7

8A-11⁄ 4 17⁄ 8 57⁄ 8 — — 9⁄ 16 5⁄ 8 81⁄ 8 11
12A-11⁄ 4 17⁄ 8 57⁄ 8 1⁄ 2 31⁄ 2 9⁄ 16 5⁄ 8 121⁄ 8 15
F A B C D
THROAT DEPTH 4A-11⁄ 2 17⁄ 8 17⁄ 8 — — 9⁄ 16 3⁄ 4 41⁄ 8 7
G
H 8A-11⁄ 2 17⁄ 8 57⁄ 8 — — 9⁄ 16 3⁄ 4 81⁄ 8 11
12A-11⁄ 2 17⁄ 8 57⁄ 8 1⁄ 2 31⁄ 2 9⁄ 16 3⁄ 4 121⁄ 8 15
18A-11⁄ 2 17⁄ 8 57⁄ 8 1⁄ 2 57⁄ 8 9⁄ 16 3⁄ 4 181⁄ 8 21
4A-2 17⁄ 8 17⁄ 8 — — 9⁄ 16 1 41⁄ 8 7

8A-2 17⁄ 8 57⁄ 8 — — 9⁄ 16 1 81⁄ 8 11
8AH-2 1⁄ 2 2 5 — — 9⁄ 16 33⁄ 8 81⁄ 2 12 12A-2 17⁄ 8 57⁄ 8 1⁄ 2 31⁄ 2 9⁄ 16 1 121⁄ 8 15
12AH- 2 1⁄ 2 2 5 1 33⁄ 8 9⁄ 16 33⁄ 8 121⁄ 2 16 18A-2 17⁄ 8 57⁄ 8 1⁄ 2 57⁄ 8 9⁄ 16 1 181⁄ 8 21
18AH- 2 1⁄ 2 2 5 1 57⁄ 8 9⁄ 16 33⁄ 8 181⁄ 2 22
4A-21⁄ 2 17⁄ 8 17⁄ 8 — — 9⁄ 16 13⁄ 8 41⁄ 8 7
8AH- 3 23⁄ 8 45⁄ 8 — — 9⁄ 16 35⁄ 16 81⁄ 2 115⁄ 8 8A-21⁄ 2* 17⁄ 8 57⁄ 8 — — 9⁄ 16 13⁄ 8 81⁄ 8 11
12AH- 3 23⁄ 8 45⁄ 8 1 33⁄ 8 9⁄ 16 35⁄ 16 121⁄ 2 155⁄ 8 12A-21⁄ 2* 17⁄ 8 57⁄ 8 1⁄ 2 31⁄ 2 9⁄ 16 13⁄ 8 121⁄ 8 15
18A-21⁄ 2* 17⁄ 8 57⁄ 8 1⁄ 2 57⁄ 8 9⁄ 16 13⁄ 8 181⁄ 8 21
8AH- 31⁄ 2 3 33⁄ 4 — — 9⁄ 16 33⁄ 4 81⁄ 2 12
12AH- 31⁄ 2 3 33⁄ 4 1 33⁄ 8 9⁄ 16 33⁄ 4 121⁄ 2 16 8A-31⁄ 2 27⁄ 8 4 — — 9⁄ 16 23⁄ 8 81⁄ 4 113⁄ 4
18AH- 31⁄ 2 3 33⁄ 4 1 57⁄ 8 9⁄ 16 33⁄ 4 181⁄ 2 22 12A-31⁄ 2 27⁄ 8 4 1 21⁄ 2 9⁄ 16 23⁄ 8 121⁄ 4 153⁄ 4
18A-31⁄ 2 27⁄ 8 6 1 41⁄ 2 9⁄ 16 23⁄ 8 181⁄ 4 213⁄ 4
8AH- 6 33⁄ 4 33⁄ 4 — — 9⁄ 16 43⁄ 4 81⁄ 2 121⁄ 2
12AH- 6 33⁄ 4 33⁄ 4 1 33⁄ 8 9⁄ 16 43⁄ 4 121⁄ 2 161⁄ 2 8A-51⁄ 2 31⁄ 2 33⁄ 4 — — 9⁄ 16 3 81⁄ 4 121⁄ 4
18AH- 6 33⁄ 4 33⁄ 4 1 57⁄ 8 9⁄ 16 43⁄ 4 181⁄ 2 221⁄ 2 12A-51⁄ 2 31⁄ 2 33⁄ 4 1 3 9⁄ 16 3 121⁄ 4 161⁄ 4
18A-51⁄ 2 31⁄ 2 33⁄ 4 1 6 9⁄ 16 3 181⁄ 4 221⁄ 4
8 OA-6 311⁄ 16 33⁄ 4 — — 9⁄ 16 413⁄ 16 81⁄ 2 121⁄ 2
12 OA-6 311⁄ 16 33⁄ 4 1 33⁄ 8 9⁄ 16 413⁄ 16 121⁄ 2 161⁄ 2 *on AJ-21⁄ 2 units “A” dimension is 21⁄ 8”, “B”&”D” dimensions
18 OA-6 311⁄ 16 33⁄ 4 1 57⁄ 8 9⁄ 16 413⁄ 16 181⁄ 2 221⁄ 2 are 55⁄ 8”.
AD Holder
HOLDER A B C E F G H
3/8 DIA. PILOT PINS (REF: .376 DIA. IN TEMPLATE) 8 AD-4 33⁄ 8 47⁄ 8 63⁄ 8 5⁄ 8 33⁄ 4 81⁄ 4 113⁄ 4
1.500 REF. E DIAMETER 12 AD-4 33⁄ 8 47⁄ 8 63⁄ 8 5⁄ 8 33⁄ 4 121⁄ 4 153⁄ 4
18 AD-4 33⁄ 8 47⁄ 8 63⁄ 8 5⁄ 8 33⁄ 4 181⁄ 4 213⁄ 4
TEMPLATE LAYOUT DESIGN INFORMATION

F A UniPunch can provide CAD files of units for use in creating templates.
TECH. DATA
B The formats that are available are DXF (2D footprint), DWG (2D
C footprint) and STEP (3D model). STEP files are available to download
THROAT DEPTH
G and are located in our Online Parts Book at www.unipunch.com or by
H contacting the UniPunch Sales Department.

100
Slot Sizes
B and BX Holders & Location
3/8 DIA. PILOT PINS (REF: .376 DIA. IN TEMPLATE) E SLOT WIDTH
1.500 REF.
F A B C D
THROAT DEPTH
G
H
4BX-3⁄ 4 13⁄ 4 2 — — 3⁄ 8 11⁄ 8 41⁄ 8 7
8BX-3⁄ 4 13⁄ 4 25⁄ 8 5⁄ 8 25⁄ 8 3⁄ 8 11⁄ 8 81⁄ 8 11
4B-1 17⁄ 8 2 — — 9⁄ 16 11⁄ 4 41⁄ 8 7

8B-1 17⁄ 8 25⁄ 8 5⁄ 8 25⁄ 8 9⁄ 16 11⁄ 4 81⁄ 8 11
4B-11⁄ 4 17⁄ 8 17⁄ 8 — — 9⁄ 16 3⁄ 4 41⁄ 8 7

8B-11⁄ 4 17⁄ 8 57⁄ 8 — — 9⁄ 16 3⁄ 4 81⁄ 8 11
12B-11⁄ 4 17⁄ 8 57⁄ 8 1⁄ 2 31⁄ 2 9⁄ 16 3⁄ 4 121⁄ 8 15
4B-13⁄ 4 17⁄ 8 17⁄ 8 — — 9⁄ 16 1 41⁄ 8 7

8B-13⁄ 4 17⁄ 8 57⁄ 8 — — 9⁄ 16 1 81⁄ 8 11
12B-13⁄ 4 17⁄ 8 57⁄ 8 1⁄ 2 31⁄ 2 9⁄ 16 1 121⁄ 8 15
18B-13⁄ 4 17⁄ 8 57⁄ 8 1⁄ 2 57⁄ 8 9⁄ 16 1 181⁄ 8 21
4BX-21⁄ 4 17⁄ 8 17⁄ 8 — — 9⁄ 16 11⁄ 4 41⁄ 8 7

8BX-21⁄ 4 17⁄ 8 57⁄ 8 — — 9⁄ 16 11⁄ 4 81⁄ 8 11
12BX-21⁄ 4 17⁄ 8 57⁄ 8 1⁄ 2 31⁄ 2 9⁄ 16 11⁄ 4 121⁄ 8 15
18BX-21⁄ 4 17⁄ 8 57⁄ 8 1⁄ 2 57⁄ 8 9⁄ 16 11⁄ 4 181⁄ 8 21
8B-3 17⁄ 8 57⁄ 8 — — 9⁄ 16 15⁄ 8 81⁄ 8 11

12B-3 17⁄ 8 57⁄ 8 1⁄ 2 31⁄ 2 9⁄ 16 15⁄ 8 121⁄ 8 15
18B-3 17⁄ 8 57⁄ 8 1⁄ 2 57⁄ 8 9⁄ 16 15⁄ 8 181⁄ 8 21
TECH. DATA
8B-5 43⁄ 8 3 — — 9⁄ 16 3 81⁄ 4 113⁄ 4

12B-5 43⁄ 8 3 11⁄ 4 3 9⁄ 16 3 121⁄ 4 153⁄ 4
18B-5 43⁄ 8 41⁄ 2 2 41⁄ 2 9⁄ 16 3 181⁄ 4 213⁄ 4

UNIPUNCH
101
Unittool Tooling and Units to replace
Unittool H, HA/HP, HH, and M Series
Compatible with existing Unittool

heavy duty and medium duty holders,
UniPunch units can utilize existing
punches, dies and other
components, and can be used right
next to a Unittool holder without any
modification in existing mounting
setups. All shut heights and die
heights are uniform.
Assemblies and replacement • Heavy-duty die springs supplied
parts in all “A” and “AH” Series
Visit the UniPunch website
UniPunch provides high quality units for increased stripping
and select the Online Parts
Book tab for cross-reference assemblies and replacement parts for pressure.
information by unit model or Unittool H & M Series Units, mounting • Toll-free 800 number for
part number. equipment, accessories and other assistance in ordering and
ww.unipunch.com/PartsBook products. For complete information, technical questions.
simply call the number below. • Fax and email service directly
The UniPunch Advantage linked to our
• A-2 5% chrome, air-hardening tool specials/quotations
steel is used to provide longer punch department for easy transmittal
life in our “A” and “B” Series units. of drawings and quick answers
This means less tool maintenance and on tooling requirements.
better resistance to chipping and • Thoroughly experienced
cracking. engineering department with
many years of practical
experience in punch and
REPL. TOOLING
die design.
UNIPUNCH SELECTION CHART
Unittool Series UniPunch Equivalent Maximum Diameter Max. Mat’l Thickness

H A 3.500" 1⁄ 4"
HA/HP AJ 1.250" 1⁄ 4"
HH AH 3.000" 1⁄ 2"
M B 3.500" 10 GA.
H Corner Notch Units–Ref. UniPunch “A” Series HZP Horizontal Units–Ref. UniPunch “HZ” Series
M Corner Notch Units–Ref. UniPunch “B” Series L Light Duty Units–Ref. UniPunch “G” Series

102
Interchangeable with
Unittool
A-1 Unit Interchangeable with H-1 Replacement Components
Unittool UniPunch
Ref. No. Part No.
SPECIFICATIONS: Punch Head HPH-107 2075
MAX. PUNCH DIA.: .4375" (11.11mm) MIN. PUNCH DIA.: .0937" (2.4mm) Round Punch HP-122 2111
MAX. SQUARE: .309" (7.85mm) MIN. SHAPE DIM.: .0937" (2.4mm) Round Punch with Head HPA-102A 2011
Shaped Punch with Head HPA-102K 2016
COMPLETE ROUND UNITS COMPLETE SHAPED UNITS Stripping Spring HSS-105 2045
Punch Retainer PR-100 2180
Model Part Unittool Model Part Unittool Round Guide HG-104 2030
No. No. Ref. No. No. Ref.
Shaped Guide HG-104K 2035
4A -1 2003 4H-1 4SA -1 2005 4H-1K Lifter Spring HLS-106 2070
8A -1 2000 8H-1 8SA -1 2006 8H-1K Round Die HD-123 2120
12A -1 2001 12H-1 12SA -1 2007 12H-1K Shaped Die HD-123K 2125
Guide Retainer GR-300 1002
Guide Retainer Screw — 91130
Pilot Pin (round) PP-1000 1001
Pilot Pin (diamond) PP-1000K 1101
For additional components and specifications - ref. A-1 catalog page 22
A-11⁄ 4 Unit Interchangeable with H-11⁄ 4 Replacement Components

Unittool UniPunch
Ref. No. Part No.
4A-11⁄ 4 2103 4H-11⁄ 4 4SA-11⁄ 4 2105 4H-11⁄ 4K Lifter Spring HLS-126 2170
8A-11⁄ 4 2100 8H-11⁄ 4 8SA-11⁄ 4 2106 8H-11⁄ 4K Round Die HD-123 2120
Shaped Die HD-123K 2125
12A-11⁄ 4 2101 12H-11⁄ 4 12SA-11⁄ 4 2107 12H-11⁄ 4K
For additional components and specifications - ref. A-11⁄ 4 catalog page 23
REPL. TOOLING

103
Unittool
Unittool UniPunch
Ref. No. Part No.
SPECIFICATIONS:
Punch Head HPH-157 2271
Model Part Unittool Model Part Unittool
Round Guide HG-154 2230
4A-11⁄ 2 2203 4H-11⁄ 2 4SA-11⁄ 2 2205 4H-11⁄ 2K
Lifter Spring HLS-156 2270
12A-11⁄ 2 2201 12H-11⁄ 2 12SA-11⁄ 2 2207 12H-11⁄ 2K Shaped Die HD-153K 2225
A-2 Unit Interchangeable with H-2 Replacement Components

Unittool UniPunch
Ref. No. Part No.
4A-2 2303 4H-2 4SA-2 2305 4H-2K Lifter Spring HLS-206 2370
8A-2 2300 8H-2 8SA-2 2306 8H-2K Round Die HD-203 2320-2
12A-2 2301 12H-2 12SA-2 2307 12H-2K Round Die (with collar) HD-203 2320-1
Shaped Die HD-203K 2325-2
Shaped Die (with collar) HD-203K 2325-1
REPL. TOOLING

For additional components and specifications - ref. A-2 catalog page 25

104
Unittool
Unittool UniPunch
Ref. No. Cat. No.
SPECIFICATIONS:
Punch Screw PS-259 2485
MAX. PUNCH DIA.:1.5000" (38.10mm) MIN. PUNCH DIA.: .2812" (7.15mm) Punch Driver HPH-257A 2484
MAX. SQUARE: 1.060" (26.92mm) MIN. SHAPE DIM.: .1250" (3.18mm) Stripping Spring (set of 10) HSS-255 2440-10
Spring Guard SG-250 2442
COMPLETE ROUND UNITS COMPLETE SHAPED UNITS Round Guide HG-254 2435
Model Part Unittool Model Part Unittool Lifter Spring HLS-256 2470
Round Punch HP-252 2411
4A-21⁄ 2 2400 4H-21⁄ 2 4SA-21⁄ 2 2405 4H-21⁄ 2K Shaped Punch HP-252K 2416
12A-21⁄ 2 2402 12H-21⁄ 2 12SA-21⁄ 2 2407 12H-21⁄ 2K Shaped Die HD-253K 2425
18A-21⁄ 2 2403 18H-21⁄ 2 18SA-21⁄ 2 2408 18H-21⁄ 2K
Tooling For H-3 Unit

Not Available
Tooling For H-3 1/2 Unit Note: No Interchangeable Units are available
SPECIFICATIONS: Replacement Punches & Dies listed below
MAX. PUNCH DIA.: 2.0000" (50.8mm) MIN. PUNCH DIA.: .5000" (12.70mm) Unittool UniPunch
Replacement Components Ref. No. Part No.
MAX. SQUARE: 1.414" (35.92mm) MIN. SHAPE DIM.: .1250" (3.18mm)
Round Punch HP-352 2510
Shaped Punch HP-352K 2517
Round Die HD353 2520
Guide Retainer Screw –– 91130
3" X 3"
H-Series Corner Notch Units Interchangeable with A-Series
REPL. TOOLING
Unittool Unipunch
Replacement Components Price
3" X 3" 5"Ref.
X 5"No. Cat. No.
Left Hand Corner Notch H-55-LCN 6010 $1,054.95
Unittool UniPunch Unittool UniPunch
Replacement Components Replacement
Right Components
Hand Corner Notch H-55-RCNRef. No.6020 $1,054.95
Part No.
Ref. No. Part No.
Left Hand Corner Notch H-33-LCN 6440 Left Hand Corner Notch H-55-LCN 6010
Note: Post Design Corner Notch Units are not available
Right Hand Corner Notch H-33-RCN 6450 Right Hand Corner Notch H-55-RCN 6020
For additional components and specifications - ref. A-Series Corner Notch Page 48
Note: Unittool Series 200 Post Design Notch Units are not available

105
Unittool
Tooling For H-5 3/4 Unit Replacement Components
Unittool UniPunch
Ref. No. Part No.
SPECIFICATIONS: Round Punch:
MAX. PUNCH DIA.:3.5000" (88.90mm) MIN. PUNCH DIA.: 1.2500" (31.75mm) From 1.2500" to 1.5625" MP-502A 8207
From 1.5630" to 2.2500" MP-502B 8208
MAX. SQUARE: 2.474" (62.84mm) MIN. SHAPE DIM.: .1250" (3.18mm) From 2.2510" to 2.8750" MP-502C 8209
From 2.8760" to 3.5000" MP-502D 8210
Note: No Interchangeable Units are available Shaped Punch:
Within 1.5000" Dia. MP-502AK 8282
Replacement Punches & Dies listed to right Within 2.5000" Dia. MP-502CK 8283
Within 3.5000" Dia. MP-502DK 8284
Round Stripper Plate MSP-509 8271
(Specify Punch Size)
Fitted Stripper Plate MSP-509K 8270
(Specify Punch Size & Shape)
Round Die HD-603 3820
Punch Locator PR-500 3880
(For Rd. Punches
1.563 Dia. to 3.500 Dia.)
Tooling for H-8 Unit Pilot Pin (round) PP-1000 1001
Not Available. See UniPunch A-8 for compatible unit page 29 Pilot Pin (diamond) PP-1000K 1101
H-Series Edge & Vee Notch Units Interchangeable with A-Series

see A Series Notch Unit pages 49 - 50
AJ-1 Unit Interchangeable with HA-1/HP-1 Replacement Components

Unittool UniPunch
Ref. No. Part No.
STANDARD UNITS (Complete With Punch, Die Button & Adapter) Stripping Spring HSS-105 2045
Model Part Unittool Model Part Unittool Shaped Guide HG-104K 2035
No. No. Ref. No. No. Ref. Lifter Spring HLS-106 2070
4AJ-1A 14000A 4HA-1 4SAJ-1A 14005A 4HA-1K Round Die HD-123 2120
8AJ-1A 14001A 8HA-1 8SAJ-1A 14006A 8HA-1K
Die Adapter HDA-108 14072
12AJ-1A 14002A 12HA-1 12SAJ-1A 14007A 12HA-1K Shaped Die Adapter HDA-108K 14074
REPL. TOOLING
Round Pedestal Die HPD-123 2121

Shaped Pedestal Die HPD-123K 2126
OPTIONAL UNITS (Complete With Punch & Pedestal Die) Guide Retainer GR-300 1002
COMPLETE ROUND UNITS COMPLETE SHAPED UNITS
Model Part Unittool Model Part Unittool Pilot Pin (diamond) PP-1000K 1101
For additional components and specifications - ref. AJ-1catalog page 30
4AJ-1P 14000P 4HP-1 4SAJ-1P 14005P 4HP-1K
8AJ-1P 14001P 8HP-1 8SAJ-1P 14006P 8HP-1K
12AJ-1P 14002P 12HP-1 12SAJ-1P 14007P 12HP-1K

106
Unittool
AJ-11⁄ 4 Unit Interchangeable with HA-11⁄ 4 / HP-11⁄ 4 Unittool UniPunch
SPECIFICATIONS:
4AJ-11⁄ 4A 14100A 4HA-11⁄ 4 4SAJ-11⁄ 4A 14105A 4HA-11⁄ 4K
Lifter Spring HLS-126 2170
8AJ-11⁄ 4A 14101A 8HA-11⁄ 4 8SAJ-11⁄ 4A 14106A 8HA-11⁄ 4K Round Die HD-123 2120
12AJ-11⁄ 4A 14102A 12HA-11⁄ 4 12SAJ-11⁄ 4A 14107A 12HA-11⁄ 4K Shaped Die HD-123K 2125
Shaped Die Adapter HDA-128K 14174
OPTIONAL UNIT (Complete With Punch & Pedestal Die)
COMPLETE ROUND UNITS COMPLETE SHAPED UNITS Shaped Pedestal Die HPD-123K 2126
No. No. Ref. No. No. Ref. Guide Retainer Screw — 91130
4AJ-11⁄ 4P 14100P 4HP-11⁄ 4 4SAJ-11⁄ 4P 14105P 4HP-11⁄ 4K
8AJ-11⁄ 4P 14101P 8HP-11⁄ 4 8SAJ-11⁄ 4P 14106P 8HP-11⁄ 4K
For additional components and specifications - ref. AJ-11⁄ 4 catalog page 31
12AJ-11⁄ 4P 14102P 12HP-11⁄ 4 12SAJ-11⁄ 4P 14107P 12HP-11⁄ 4K
AJ-11⁄ 2 Unit Interchangeable with HA-11⁄ 2 / HP-11⁄ 2 Replacement Components

Unittool UniPunch
Ref. No. Part No.
MAX. PUNCH DIA.: .6250"(15.86mm) MIN. PUNCH DIA.: .1250" (3.18mm) Round Punch HP-152 2211
4AJ-11⁄ 2A 14200A 4HA-11⁄ 2 4SAJ-11⁄ 2A 14205A 4HA-11⁄ 2K Lifter Spring HLS-156 2270
8AJ-11⁄ 2A 14201A 8HA-11⁄ 2 8SAJ-11⁄ 2A 14206A 8HA-11⁄ 2K Round Die HD-153 2220
12AJ-11⁄ 2A 14202A 12HA-11⁄ 2 12SAJ-11⁄ 2A 14207A 12HA-11⁄ 2K Shaped Die HD-153K 2225
Shaped Die Adapter HDA-158K 14274 REPL. TOOLING
OPTIONAL UNIT (Complete With Punch & Pedestal Die) Shaped Pedestal Die HPD-153K 2226
COMPLETE ROUND UNITS COMPLETE SHAPED UNITS Guide Retainer Screw — 91130
Model Part Unittool Model Part Unittool Pilot Pin (round) PP-1200 1120
No. No. Ref. No. No. Ref. Pilot Pin (diamond) PP-1000K 1101
4AJ-11⁄ 2P 14200P 4HP-11⁄ 2 4SAJ-11⁄ 2P 14205P 4HP-11⁄ 2K For additional components and specifications - ref. AJ-11⁄ 2 catalog page 32
8AJ-11⁄ 2P 14201P 8HP-11⁄ 2 8SAJ-11⁄ 2P 14206P 8HP-11⁄ 2K
12AJ-11⁄ 2P 14202P 12HP-11⁄ 2 12SAJ-11⁄ 2P 14207P 12HP-11⁄ 2K

107
Unittool
AJ-2 Unit Interchangeable with HA-2 / HP-2 Replacement Components
Unittool UniPunch
Ref. No. Part No.
SPECIFICATIONS:
STANDARD UNITS (Complete With Punch, Die Button & Adapter) Stripping Spring HSS-205 2340
Model Part Unittool Model Part Unittool Shaped Guide HG-204K 2335
No. No. Ref. No. No. Ref. Lifter Spring HLS-206 2370
4AJ-2A 14300A 4HA-2 4SAJ-2A 14305A 4HA-2K Round Die HD-203 2320-2
Round Die (with collar) HD-203 2320-1
8AJ-2A 14301A 8HA-2 8SAJ-2A 14306A 8HA-2K
Shaped Die HD-203K 2325-2
12AJ-2A 14302A 12HA-2 12SAJ-2A 14307A 12HA-2K Shaped Die (with collar) HD-203K 2325-1
Shaped Die Adapter HDA-208K 14374
OPTIONAL UNITS (Complete With Punch and Pedestal Die) Round Pedestal Die HPD-203 2321
COMPLETE ROUND UNITS COMPLETE SHAPED UNITS Guide Retainer GR-300 1002
Model Part Unittool Model Part Unittool Guide Retainer Screw — 91130
No. No. Ref. No. No. Ref. Pilot Pin (round) PP-1200 1120
4SAJ-2P 14300P 4HP-2 4SAJ-2P 14305P 4HP-2K Pilot Pin (diamond) PP-1000K 1101
8SAJ-2P 14301P 8HP-2 8SAJ-2P 14306P 8HP-2K For additional components and specifications - ref. AJ-2 catalog page 33
12SAJ-2P 14302P 12HP-2 12SAJ-2P 14307P 12HP-2K
AJ-21⁄ 2 Unit Interchangeable with HP-21⁄ 2 Replacement Components

Unittool UniPunch
Ref. No. Part No.
SPECIFICATIONS: Punch Screw PS-259 2485
MAX. PUNCH DIA.: 1.250" (31.75mm) MIN. PUNCH DIA.: .2812" (7.14mm) Punch Driver HPH-257A 2484
MAX. SQUARE: 1.060" (26.92mm) MIN. SHAPE DIM.: .1250" (3.18mm) Stripping Spring (set of 10) HSS-255 2440-10
Spring Guard SG-250 2442
Round Guide HG-254 2435
COMPLETE ROUND UNITS COMPLETE SHAPED UNITS Shaped Guide HG-254K 2435
Model Part Unittool Model Part Unittool Lifter Spring HLS-256 2470
No. No. Ref. No. No. Ref. Round Punch HP-252 14411
8AJ-21⁄ 2P 14401P 8HP-21⁄ 2 8SAJ-21⁄ 2P 14406P 8HP-21⁄ 2K Shaped Punch HP-252K 14416
REPL. TOOLING
Pedestal Die HPD-253 2422

12AJ-21⁄ 2P 14402P 12HP-21⁄ 2 12SAJ-21⁄ 2P 14407P 12HP-21⁄ 2K
For additional components and specifications - ref. AJ-21⁄ 2 catalog page 34

108
Unittool
AH-21⁄ 2 Unit Interchangeable with HH-21⁄ 2 Replacement Components
Unittool UniPunch
Ref. No. Part No.
SPECIFICATIONS: Punch Head HHPH-257 2671
MAX. PUNCH DIA.:1.0000" (25.40mm) MIN. PUNCH DIA.: .2500" (6.35mm) Punch Screw N.A. 91025
MAX. SQUARE: .707" (17.96mm) MIN. SHAPE DIM.: .1250" (3.18mm) Round Punch HHP-252 2611
Round Punch with Head HHPA-252A 2610
Shaped Punch HHP-252K 2616
COMPLETE ROUND UNITS COMPLETE SHAPED UNITS Shaped Punch with Head HHPA-252K 2615
Model Part Unittool Model Part Unittool Punch Plate HHPP-250 2677
No. No. Ref. No. No. Ref. Spring Retainer (set of 2) HHSR-100 2681-2
8AH-21⁄ 2 2600 8HH-21⁄ 2 8SAH-21⁄ 2 2605 8HH-21⁄ 2K Stripper Bolt (spring retainer)
N.A. 2682
(2 req’d)
12AH-21⁄ 2 2601 12HH-21⁄ 2 12SAH-21⁄ 2 2606 12HH-21⁄ 2K Stripping Spring (set of 2) HHSS-255 2540-2
Lifter Spring (set of 2) HHLS-256 2673-2
Stripper Bolt (lifter) N.A. 2683
Stripper Plate HHSP-259 2676
Key (punch) HHPK-100 2778
Punch Retainer HHPR-100 2680
Round Die HHD-253 2620
Shaped Die HHD-253K 2625
Round Die Holder N.A. 2674
Shaped Die Holder HHDH-258K 2675
For additional components and specifications - ref. AH-21⁄ 2 catalog page 36
AH-3 Unit Interchangeable with HH-3 Replacement Components

Unittool UniPunch
Ref. No. Part No.
SPECIFICATIONS: Punch Screw N.A. 91260
MAX. PUNCH DIA.:1.3750" (34.92mm) MIN. PUNCH DIA.: .3750" (9.53mm) Punch Plate HHPP-307 3772
MAX. SQUARE: .972" (24.68mm) MIN. SHAPE DIM.: .1250" (3.18mm) Punch Driver HHD-309 3779
Key (punch driver) HPK-302 3778
Stripping Spring
COMPLETE ROUND UNITS COMPLETE SHAPED UNITS N.A. 3741-2
(1"OD x 3"lg) (set of 2)
Stripping Spring
Model Part Unittool Model Part Unittool HHSS-305 3740-2
(2"OD x 3"lg) (set of 2)
No. No. Ref No. No. Ref.
Spring Spacer (2 req’d) N.A. 3742
8AH-3 3700 8HH-3 8SAH-3 3705 8HH-3K
Stripper Bolt (4 req’d) N.A. 3784
12AH-3 3701 12HH-3 12SAH-3 3706 12HH-3K Lifter Spring (set of 4) HHLS-306 3774-4
Stripper Plate HHSP-308 3773 REPL. TOOLING
Round Punch HHP-302 2513
Die Key HHDK-303-1 3777
For additional components and specifications - ref. AH-3 catalog page 37

109
Unittool
AH-31⁄ 2 Unit Interchangeable with HH-31⁄ 2 Replacement Components
Unittool UniPunch
Ref. No. Part No.
SPECIFICATIONS:
Punch Screw N.A. 91072
MAX. PUNCH DIA.:2.0000" (50.80mm) MIN. PUNCH DIA.: .5000" (12.7mm) Round Punch Driver N.A. 2582
MAX. SQUARE: 1.414" (35.9mm) MIN. SHAPE DIM.: .1250" (3.18mm) Shaped Punch Driver HHPD-354K 2583
Round Punch HHP-352 2511
COMPLETE ROUND UNITS COMPLETE SHAPED UNITS Shaped Punch HHP-352K 2515
Punch Plate HHPP-350 2572
Model Part Unittool Model Part Unittool Spring Retainer (set of 2) HHSR-100 2681-2
Stripper Bolt
8AH-31⁄ 2 2500 8HH-31⁄ 2 8SAH-31⁄ 2 2505 8HH-31⁄ 2K N.A. 2682
(spring retainer) (2 req’d)
12AH-31⁄ 2 2501 12HH-31⁄ 2 12SAH-31⁄ 2 2506 12HH-31⁄ 2K Stripping Spring (set of 2) HHSS-255 2540-2
Lifter Spring (set of 2) HHLS-256 2673-2
Stripper Bolt (lifter) (2 req’d) N.A. 2683
Key (driver) HHPK-100 2778
For additional components and specifications - ref. AH-31⁄ 2 catalog page 38
AH-6 Unit Interchangeable with HH-51⁄ 2 Unittool UniPunch

SPECIFICATIONS:
MAX. PUNCH DIA.: 3.000" (76.2mm) MIN. PUNCH DIA.: 1.000" (25.4mm) Punch Driver HHPD-554K 2779
MAX. SQUARE: 2.121" (53.87mm) MIN. SHAPE DIM.: .1875" (4.76mm) Round Punch HHP-552 2512
COMPLETE ROUND UNITS COMPLETE SHAPED UNITS Punch Plate HHPP-550 2772
Spring Retainer (set of 4) HHSR-100 2681-4
No. No. Ref. No. No. Ref. Stripper Bolt N.A. 2684
(spring retainer) (4 req’d)
8AH-6 2700 8HH-51⁄ 2 8SAH-6 2706 8HH-51⁄ 2K Stripping Spring (set of 4) HHSS-255 2540-4
12AH-6 2701 12HH-51⁄ 2 12SAH-6 2707 12HH-51⁄ 2K Lifter Spring (set of 2) HHLS-256 2673-2
Stripper Bolt (lifter) (2 req’d) N.A. 2685
Key (driver) HHPK-100 2778
REPL. TOOLING

For additional components and specifications - ref. AH-6 catalog page 39

110
Unittool
BX-3⁄ 4 Unit Interchangeable with M-3⁄ 4 Replacement Components
Unittool UniPunch
Ref. No. Part No.
SPECIFICATIONS: Stripper Bolt (2 req’d) MSB-078 3033
MAX. PUNCH DIA.: .3125" (7.93mm) MIN. PUNCH DIA.: .0937" (2.38mm) Retainer Plate MR-079 3032
MAX. SQUARE: N.A. MIN. SHAPE DIM.: N.A. Punch Screw N.A. 91203
Punch Head MPH-077 3171
COMPLETE ROUND UNITS Round Punch MP-072 3111
Round Punch with Head MPA-072A 3110
Model Part Unittool Stripping Spring MSS-075 3040
No. No. Ref. Guide MG-074 3030
4BX-3⁄ 4 3000 4M-3⁄ 4 Lifter Spring MLS-076 4273
8BX-3⁄ 4 3001 8M-3⁄ 4 Die (.490" O.D.) MD-073 3121
For additional components and specifications - ref. BX-3⁄ 4 catalog page 55.
Tooling For M-1 Unit Replacement Components

Unittool UniPunch
Ref. No. Part No.
SPECIFICATIONS:
MAX. PUNCH DIA.: .3125" (9.52mm) MIN. PUNCH DIA.: .0937" (2.38mm) Punch Head MPH-107 3271
MAX. SQUARE: N.A. MIN. SHAPE DIM.: N.A. Round Punch MP-122 3211
Round Punch with Head MPA-102A 3210
Die (.688" O.D.) MD-103 3221
Note: No Interchangeable Units are available Pilot Pin (round) PP-1000 1001
Replacement Punches & Dies are listed to right
Tooling For M-11⁄ 4 Unit Replacement Components

Unittool UniPunch
Ref. No. Part No.
SPECIFICATIONS: Punch Retainer MPR-128 3372
MAX. PUNCH DIA.: .3750" (9.52mm) MIN. PUNCH DIA.: .0937" (2.38mm) Punch Screw N.A. 91203
MAX. SQUARE: .265" (6.73mm) MIN. SHAPE DIM.: .0937" (2.38mm) Punch Head MPH-127 3371
Round Punch MP-122 3211
Round Punch w/ Head MPA-122A 3310
Note: No Interchangeable Units are available Shaped Punch MP-122K 3316
See UniPunch B-11⁄4 catalog page for compatible Shaped Punch w/ Head MPA-122K 3315
complete punching units. See page 57 Round Stripping Guide
MG-124 3323
w/ Open Stripper
Shaped Stripping Guide
MG-124K 3324
w/ Open Stripper REPL. TOOLING
Round Die (15/16" O.D.) MD-123 3321
Shaped Die (15/16" O.D.) MD-123K 3326
Guide Retainer N.A. 1080
Guide Retainer Screw (2 req’d) N.A. 91123

111
Unittool
Tooling for M-13⁄ 4 Replacement Components
Unittool UniPunch
Ref. No. Part No.
SPECIFICATIONS:
Punch Retainer MPR-178 3472
MAX. PUNCH DIA.: .5000" (12.70mm) MIN. PUNCH DIA.: .1250" (3.18mm) Punch Screw N.A. 91230
Round Punch w/ Head MPA-172A 3410
Note: No Interchangeable Units are available
Shaped Punch MP-172K 3416
See UniPunch B-1¾ catalog page for compatible complete
Shaped Punch w/ Head MPA-172K 3415
punching units. See Page 58 Round Stripping Guide
MG-174 3423
w/ Open Stripper
Shaped Stripping Guide
MG-174K 3427
w/ Open Stripper
Round Die (1" O.D.) MD-173 3421
Shaped Die (1" O.D.) MD-173K 3426
Guide Retainer N.A. 7664
Guide Retainer Screw (2 req’d) N.A. 91123
Tooling for M-21⁄ 4 Replacement Components

Unittool UniPunch
Ref. No. Part No.
SPECIFICATIONS:
Punch Retainer MPR-228 3572
MAX. PUNCH DIA.: 1.000" (25.40mm) MIN. PUNCH DIA.: .2500" (6.35mm) Punch Screw N.A. 91250
Note: No Interchangeable Units are available Round Punch w/ Head MPA-222A 3510
See UniPunch BX-2¼ catalog page for compatible complete Shaped Punch MP-222K 3516
punching units. See Page 59 Shaped Punch w/ Head MPA-222K 3515
Round Stripping Guide MG-224 3530
Shaped Stripping Guide MG-224K 3535
Round Die (1 5/8" O.D.) MD-223 3521
Shaped Die (1 5/8" O.D.) MD-223K 3526
Guide Retainer MGR-300 1030
Guide Retainer Screw N.A. 91220
REPL. TOOLING
Tooling For M-21⁄ 2 Unit Replacement Components

Unittool UniPunch
Ref. No. Part No.
SPECIFICATIONS:
Round Punch MP-252 3610-2
MAX. PUNCH DIA.:1.5000" (38.10mm) MIN. PUNCH DIA.: .5000" (12.70mm) Shaped Punch MP-252K 57859
MAX. SQUARE: 1.060" (26.92mm) MIN. SHAPE DIM.: .1250" (3.18mm) Round Die MD-253 2420
Shaped Die MD-253K 2425
Note: No Interchangeable Units are available Pilot Pin (round) PP-1000 1001
Replacement Punches & Dies are listed to right. Pilot Pin (diamond) PP-1000K 1101

112
Unittool
B-3 Unit Interchangeable with M-3 Unittool UniPunch
SPECIFICATIONS:
MAX. PUNCH DIA.: 2.000" (50.80mm) MIN. PUNCH DIA.: .5000" (12.70mm) Punch Head MPH-307 3671
MAX. SQUARE: 1.414" (35.91mm) MIN. SHAPE DIM.: .1250" (3.18mm) Lifter Spring MLS-306 3670
Stripper Spring (6 req’d) MSS-305 3640
COMPLETE ROUND UNITS COMPLETE SHAPED UNITS Round Guide N.A. 3675
Shaped Guide MG-304K 3675
No. No. Ref. Punch Driver MPD-308 3611
No. No. Ref.
Round Punch Tip
8B-3 3600 8M-3 8SB-3 3606 8M-3K MP-302 3610-1
(over 1.124")
12B-3 3601 12M-3 12SB-3 3607 12M-3K Round Punch Tip
MP-302-1 3610-2
(under 1.125")
Shaped Punch MP-302K 3615
Round Die HD-303 3620
For additional components and specifications - ref. B-3 catalog page 60
B-5 Unit Interchangeable with M-5 Replacement Components

Unittool UniPunch
Ref. No. Part No.
SPECIFICATIONS: Punch Screw N.A. 91152
MAX. PUNCH DIA.:3.5000" (88.90mm) MIN. PUNCH DIA.:1.0000" (25.40mm) Punch Head MPP-507 3873
MAX. SQUARE: 2.474" (62.84mm) MIN. SHAPE DIM.: .1250" (3.18mm) Lifter Spring (4 req’d) MLS-506 3870
Stripper Spring (12 req’d) MSS-305 3840
COMPLETE ROUND UNITS COMPLETE SHAPED UNITS Shaped Guide MG-504K 3881
Punch Sleeve MPD-508 3871
Model Part Unittool Model Part Unittool Locator PR-500 3880
8B-5 3800 8M-5 8SB-5 3805 8M-5K Shaped Punch UMP-502K 3815
12B-5 3801 12M-5 12SB-5 3806 12M-5K Round Die HD-603 3820
Tooling for M-8 Unit REPL. TOOLING
Not Available For additional components and specifications - ref. B-5 catalog page 61
M-Series Corner Notch Units Interchangeable with B-Series

5" X 5" 3" X 3"
Unittool UniPunch Unittool UniPunch
Replacement Components Ref. No. Part No. Replacement Components Ref. No. Part No.
Left Hand Corner Notch M-55-LCN 7010 Left Hand Corner Notch M-33-LCN 7040
Right Hand Corner Notch M-55-RCN 7020 Right Hand Corner Notch M-33-RCN 7050
For additional components and specifications - ref. B-Series Corner Notch page 62 Note: Post Design Corner Notch Units are not available

113
Glossary
A-2 Tool Steel: All “A” and “B” Series punches use A-2 5% chrome Inside Diameter (ID): The diameter on the inside of an object, e.g. a
air hardening tool steel. Compared to oil hardened tool steel, this tube or pipe.
premium tool steel provides longer tool life and better resistance to Key: The device used to locate and position tooling within the holder.
chipping and cracking. An example would be the external pin found on most UniPunch
Angle Settings: Most UniPunch shaped tools can be used in two shaped punches.
positions. Standard keying is typically 0 & 90 degrees. Other angular Keyhole: A shaped hole commonly used to facilitate part assembly.
settings are available upon request. See page 91. See page 91.
Blanking: Blanking is the process of cutting a desired shape out of a Knockout: The result of cutting and forming material so the slug is
flat piece of sheet metal. The punched slug is the finished product. held to the material by tabs. Commonly used in electrical panels and
For blanking the punch has no shear and the die size determines the boxes. See page 93.
actual blank size.
Lance and Form: Slitting and forming a pocket opening in the part.
Burr: The rough edge that protrudes on the bottom side of a hole See page 92.
after punching.
Louver: A slit cut and formed in material; for example, air vent
Chisel Shear: An angle on the punch face for the purpose of openings.
reducing tonnage required.
Modular Tooling: A system of tooling assembled from standard,
Cluster: A grouping of holes. reusable components. UniPunch modular tooling includes units for
Coping: The process of trimming or notching the end of tubing (or punching and/or notching, components for part gauging, and press
pipe) to fit against another piece of tubing, for example for welding mounting equipment for working with flat or formed material,
joints. structural shapes, extrusions, tubing and pipe.
Countersink: A conical hole in sheet metal to accept a flathead Mounting Systems: Bases for holding UniPunch tooling and gauges
screw or other fastener. within a punch press or press brake.
Die: The tool that supports the sheet metal as the punch penetrates Multicyl: An air over oil cylinder used as an alternate power source
through it. to actuate UniPunch tooling in lieu of a press or press brake.
Die Block: The device that clamps the die into the UniPunch C-frame Notching: The process of cutting two or more sides; for example,
holder. from the edge of sheet metal or angle.
Die Clearance: This is the space between the cutting edge of the Outside Diameter (OD): The distance across the outside of an object;
punch and the cutting edge of the die. Optimal die clearance is for example, tubing or pipe.
determined by the thickness and type of material being punched. Pilot Pin: The locating device found at the base of UniPunch tooling
See page 97. for positioning the unit to a template or unispacer.
Die Height: The distance from the bottom of the holder to the top Punch: The tool that goes through the material to make a hole.
die surface.
Radius Corner: (1) The sharp corner(s) on the punch or die that have
Emboss: A raised or sunken form in sheet metal made without cutting been rounded. See page 99. (2) The corner of a work piece that
the material. has been trimmed to form the arc of a circle. See page 92.
Extrusion: A forming operation forcing the material into a larger die Shim: A thin metal spacer assembled into a UniPunch unit to extend
hole; for example, to accept self-tapping screws. the punch length or die height after sharpening.
Feed Clearance: The opening above the die surface through which Shut Height: The total height from the bottom of the holder to the
the work piece is inserted when the UniPunch unit is in the open top of the punch with the UniPunch unit in the normal closed
position. position. See unit pages for individual operating specifications.
Gauge: (1) A work stop or pin locating device for positioning the Slug: The material removed to create the hole or notch. The slug is
material within the UniPunch system. (2) A system of measurement usually scrap. In blanking the slug is the desired part.
that defines the thickness of sheet metal.
Stripper Plate: A metal plate designed to surround the punch to
Galling: Metal deposits that build up on punch tips or on the inner assist in parting the punch from the material.
diameters of guides.
Stripping: The process of removing the punch from the material.
Guide/Guide Assembly: The sleeve that supports the punch and its
components within the holder. Guides also serve to hold the Template: A locating plate for positioning UniPunch units according
material in place while the punch is being stripped from the material. to the requirements of the part being punched.
Heeled Punch: A punch with a heel that engages the die before the Tonnage: The force required for punching and/or notching material.
cutting edges contact the work piece. Primarily used for edge Tube Mandrel: A support on the inside of a tube used in punching
notching. holes in tube or pipe that prevents dimpling and part deformation.
Holder: In the UniPunch system, the component that houses the Unit: The term used for the completely assembled self-contained
punch, die, guide and/or related components that make up a punching device.
TECH. DATA
complete unit.
UNIPUNCH
114
UNIPUNCH PRODUCTS, INC.
TERMS AND CONDITIONS OF SALE
1. Offer, Governing Provisions and Cancellation. Any agreement between UniPunch Products, Inc. (“UniPunch”) and a buyer for the sale of
goods and/or services described in a UniPunch Quotation or UniPunch Order Acknowledgement will be in accordance with these terms and conditions.
A UniPunch Quotation is an offer, and a UniPunch Order Acknowledgement is an offer or counter-offer by UniPunch to sell the goods and/or services
described thereon and such documents are not an acceptance of any offer made by a buyer and are expressly conditioned on buyer’s assent to these
Terms and Conditions of Sale. UniPunch objects to any additional or different terms contained in any purchase order or other communication previously
or hereafter provided by buyer to UniPunch. No such additional or different terms or conditions will be of any force or effect. The terms contained in or
incorporated into a UniPunch Quotation or UniPunch Order Acknowledgement will be the entire agreement between UniPunch and buyer on the subject of
the transaction described thereon; and there are no conditions to that agreement that are not so contained or incorporated. THE OFFER BY
UNIPUNCH AND THE RESULTANT AGREEMENT SHALL BE GOVERNED BY AND CONSTRUED ACCORDING TO THE LAWS
OF THE STATE OF WISCONSIN AND THE U.S. (WITHOUT REFERENCE TO PRINCIPLES OF CONFLICTS OF LAWS). THE
RIGHTS AND OBLIGATIONS OF THE PARTIES SHALL NOT BE GOVERNED BY THE 1980 U.N. CONVENTION ON
CONTRACTS FOR THE INTERNATIONAL SALE OF GOODS.
No accepted offer may be cancelled or altered by buyer except upon terms and conditions accepted by UniPunch in writing; and no changes
will be binding unless set forth in writing and manually signed by UniPunch. An offer by UniPunch may be revoked by UniPunch at any time before it is
accepted by buyer, and shall automatically expire 45 calendar days after its date if buyer has not accepted it before then. Neither buyer’s acceptance of
an offer nor any conduct by UniPunch (including but not limited to shipment of goods) shall oblige UniPunch to sell to buyer any quantity of goods in
excess of the quantity that buyer has committed to purchase from UniPunch at the time of such acceptance or conduct.
2. Credit Approval; Payment Terms. All payment terms set forth in this document are subject to UniPunch’s approval of buyer’s credit, in
UniPunch’s discretion; and if such approval is withheld, payment shall be due in advance of UniPunch’s performance. Except as otherwise provided on the
face of a UniPunch Quotation or UniPunch Order Acknowledgement or in the preceding sentence, payment is due upon buyer’s receipt of UniPunch’s
invoice following shipment. Interest will be charged at the lesser of (i) 18% per year, or (ii) the highest rate permitted by applicable law, on accounts more
than 30 calendar days past due. If production or shipment of completed goods, or other UniPunch performance, is delayed by buyer, UniPunch may
immediately invoice, and buyer shall pay, the percentage of the purchase price corresponding to the percentage of completion; in addition, buyer shall
compensate UniPunch for storage of completed goods or work in process during any such delay, whether stored at UniPunch’s facility or an independent
storage company’s facilities.
3. Taxes and Other Charges. Any manufacturer’s tax, occupation tax, use tax, sales tax, excise tax, value added tax, duty, custom, inspection
or testing fee, or any other tax, fee, interest or charge of any nature whatsoever imposed by any governmental authority on or measured by the
transaction between UniPunch and buyer shall be paid by buyer in addition to the prices quoted or invoiced. In the event UniPunch is required to pay any
such taxes or other charges, buyer shall reimburse UniPunch therefor on demand.
4. Delivery, Claims and Force Majeure. Unless otherwise provided on the face of a UniPunch Quotation or UniPunch Order Acknowledgement,
goods shall be delivered to buyer F.O.B. UniPunch’s loading dock or, for ultimate destinations outside of the U.S., ex works UniPunch’s loading dock (as
the latter shipping term is defined in Incoterms 2010). Delivery of products to the carrier shall constitute delivery to buyer; and regardless of shipping
terms or freight payment, buyer shall bear all risk of loss or damage in transit. UniPunch reserves the right to make delivery in installments; all such
installments to be separately invoiced and paid for when due in accordance with their respective invoice, without regard to subsequent deliveries. Delay in
delivery of any installment shall not relieve buyer of its obligations to accept remaining deliveries.
Claims for shortages or other errors in delivery must be made in writing to UniPunch within 10 calendar days after receipt of shipment; and
failure to give such notice shall constitute unqualified acceptance and a waiver of all such claims by buyer. Claims for loss of or damage to goods in
transit must be made to the carrier, and not to UniPunch.
All delivery dates are approximate. UniPunch shall not be liable for any losses or damages as a result of any delay or failure to deliver due to
any cause beyond UniPunch’s reasonable control, including but not limited to any act of God, act of buyer, embargo or other governmental act, regulation
or request, fire, accident, strike, slowdown, war, act of terrorism, riot, delay in transportation, or inability to obtain necessary labor, materials or
manufacturing facilities. In the event of any such delay, the date of delivery shall be extended for a period equal to the time lost because of the delay.
Buyer’s exclusive remedy for other delays and for UniPunch’s inability to deliver for any reason shall be rescission of its agreement to purchase.
5. Changes. UniPunch may at any time make such changes in design and construction of products, components or parts as UniPunch deems
appropriate, without notice to buyer. UniPunch may furnish suitable substitutes for materials unobtainable because of priorities or regulations established
by governmental authority or nonavailability of materials from suppliers.
6. UniPunch’s Limited Warranty. UniPunch’s Limited Warranty is as follows:
a. Basic Limited Warranty Coverage. Unipunch Products, Inc. (“UniPunch”) warrants that it will repair or, at its option, replace any
parts manufactured by UniPunch and found to be defective in factory material or workmanship within a period of 30 days after
delivery to the original purchaser.
b. UniPunch’s Obligations. UniPunch will at its expense repair or, at its option, replace F.O.B. UniPunch’s loading dock or, for
customers outside the United States, ex works UniPunch’s loading dock (as the latter shipping term is defined in Incoterms 2010)
any parts manufactured by it and found to be defective in material or workmanship during the applicable warranty period, provided

115
that the owner of the warranted goods complies with the “Warranty Claims Procedure” set forth below. The owner of the
warranted goods will be responsible for the expense of returning any parts to UniPunch for warranty evaluation. UniPunch will at its
expense return any part repaired or replaced under this warranty to the owner of the warranted goods, by truck, United Parcel
Service or U.S. Mail, at UniPunch’s option. The owner of the warranted goods will be responsible for the cost of any other method
of shipment including air freight.
c. Items Not Covered. UniPunch’s limited warranty does not cover:
i. a mechanic’s travel time;
ii. the cost of removal of defective parts and reinstallation of repaired or replacement parts;
iii. used goods, unless specifically covered by a separate written warranty;
iv. component parts manufactured by others, including, but not limited to springs and hydro-pneumatic actuators, (but, if
new, such items are ordinarily warranted by the manufacturer thereof);
v. depreciation or damage caused by normal wear and tear, accident, abuse, improper maintenance, abnormal use, use
other than in accordance with UniPunch’s instruction, or improper protection in storage,
vi. goods which have been modified or altered other than with the prior written approval of UniPunch; or
vii. the cost of normal maintenance or service, including but not limited to the cost of lubrication, and replacement of con-
sumable components such as punches, dies, springs, and guides; the cost of repairing or replacing other property which is damaged
when the goods do not work properly.
d. Warranty Claims Procedure. Within five (5) days of the expiration of the applicable warranty period, the owner of any
warranted item claimed to be defective must:
i. notify UniPunch immediately upon discovery of any defect covered by this warranty;
ii. provide UniPunch documentary evidence of the date of delivery of the item to the original purchaser; and
iii. if requested by UniPunch, ship the defective part(s) to UniPunch, freight (and duty if any) prepaid, for inspection.
e. No Other Warranties. UniPunch makes no warranty other than that set forth above, express or implied. None of
UniPunch’s representatives is authorized to make any representation or warranty on UniPunch’s behalf or in its name. UniPunch’s
only obligation and its customer’s only remedies, in connection with the sale of UniPunch products, are those set forth in this
Warranty.
THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER REPRESENTATIONS AND WARRANTIES, EXPRESS
OR IMPLIED; AND UNIPUNCH EXPRESSLY DISCLAIMS AND EXCLUDES ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF
DEALING OR USAGE OF TRADE.
7. Patents, Trademarks and Copyrights. UNIPUNCH GIVES NO WARRANTY THAT THE PRODUCTS SOLD WILL BE
DELIVERED FREE OF THE RIGHTFUL CLAIM OF ANY THIRD PARTY FOR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR
TRADEMARK OR ANY OTHER PROPRIETARY RIGHTS.
8. Consequential Damages and Other Liability; Indemnity. IN NO EVENT SHALL UNIPUNCH BE RESPONSIBLE FOR ANY
OTHER OBLIGATIONS OR LIABILITIES OR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES, INCLUDING BUT NOT
LIMITED TO DAMAGES FOR LOSS OF PRODUCTION, LOSS OF PROFITS, OR RENTAL OF SUBSTITUTE EQUIPMENT,
WHETHER ARISING OUT OF BREACH OF WARRANTY OR OTHER BREACH OF CONTRACT, NEGLIGENCE OR OTHER TORT,
OR ON ANY STRICT LIABILITY THEORY OR UNDER OTHER THEORIES OF LAW OR EQUITY, WITH RESPECT TO GOODS
OR SERVICES SOLD BY UNIPUNCH, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATING THERETO. Without limiting
the generality of the foregoing, UniPunch specifically disclaims any liability for property damages, penalties, special or punitive damages, damages for lost
profits or revenues, down-time, lost goodwill, cost of capital, cost of substitute goods or services, or for any other types of economic loss, or for claims
of buyer’s customers or any third party for any such damages, costs or losses. UNIPUNCH SHALL NOT BE LIABLE FOR AND DISCLAIMS
ALL CONSEQUENTIAL, INCIDENTAL, INDIRECT AND CONTINGENT DAMAGES WHATSOEVER. UniPunch’s liability with respect to
the goods or services sold hereunder shall be limited to the warranty provided in section 6 of these Terms and Conditions of Sale and, with respect to
any other breaches of its contract with buyer, shall be limited to the contract price.
Buyer shall indemnify and hold harmless UniPunch from and against any and all losses, liabilities, damages and expenses (including but not
limited to attorneys’ fees and other costs of defense) that UniPunch may incur as a result of any claim by buyer or by buyer’s customers or by any third
party arising out of or in connection with the goods or services sold hereunder, including but not limited to any such claim based upon the negligence of
UniPunch in designing, manufacturing, performing and/or selling such goods or services, unless such losses, liabilities, damages or expenses are
ultimately determined to be attributable solely to the willful misconduct of UniPunch.
9. Technical Information. Buyer agrees any sketches, models or samples submitted by UniPunch and any designs developed in fulfillment of
Buyer’s order shall remain the property of UniPunch, and shall be treated as confidential information unless UniPunch has in writing indicated a contrary
intent. Buyer agrees not to use or disclose such sketches, models or samples, or any design or production techniques revealed thereby, without the
express, prior written consent of UniPunch.
10. Tools. Any dies, jigs or tools that UniPunch manufactures or acquires in connection with its performance under a UniPunch Quotation or
UniPunch Order Acknowledgement shall remain the property of UniPunch, notwithstanding any charges to buyer therefor. Any such charges convey to
buyer the right to have the tools, dies or jigs used by UniPunch for performance of UniPunch’s agreement with buyer, but do not convey title or right of
possession or any other right.
UNIPUNCH
116 / 1998-1999 Catalog

Catalog 2021

Uploaded by

Copyright:

Available Formats

Catalog 2021

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Catalog 2021

Uploaded by

Copyright:

Available Formats

CATALOG AND PARTS BOOK

TABLE OF CONTENTS 

A Series Lineup 19-21  Pick-up Gauges 16

42 HZ Series Feed Rails 17 

Additional Products  Upper Arm Kits 85

MINIMUM REQUIRED INFORMATION

For UniPunch Products, Inc. Terms

Heeled Punches: Page 92

Chisel Shear on Punches: Page 94

Back Taper on Punches: Page 99

Stub Tip on Punches: Page 99

Radius Corners: Page 99

Ph: (800) 828-7061 • (715) 263-3900 • Email: [email protected] • Web: www.unipunch.com

SPECIFICATIONS & OPERATING INSTRUCTIONS

Model Part Model Part Throat Length Shipping Shaped hole

1/8" 91130 UNITS SHIPPED WITH

expanded view Basic unit

1-1/8" O.D. 3-1/2"

HOLES IN PARTS. FAST.

UNIPUNCHHOLES IN PARTS. FAST.

SHAPED HOLE CONVERSION KITS Shaped Die Options

• 91310 SOCKET SET SCREW.. . . . . .

• 1018 GUIDE RETAINER . . . . . . . . . . .

• 91312 SOCKET SET SCREW #10 - x 1/4

• 91601 1/4" LOCKWASHER . . . . . . . .

UniPunch Modular Tooling

✓Multiple holes and

✓Short lead time

Install it in your press or stand alone system.

Punch it. Profit.

The UniPunch System PUNCH, DIE AND PILOT PIN

UniPunch Modular Tooling: the solution for a variety of applications

Ph: (800) 828-7061 • (715) 263-3900 • Email: [email protected] • Web: www.unipunch.com

Straight Line Punching Press Brakes

BED RAIL / STRIP TEMPLATE

■ For straight line punching

Fast Changeover from part to part

All-Purpose For Presses &

UNIVERSAL BASE PLATES with a uniform

CUSTOM BED RAILS AND T-SLOTTED PLATES

Note: For further information on press mounting and gauging methods,

Ph: (800) 828-7061 • (715) 263-3900 • Email: [email protected] • Web: www.unipunch.com

BED RAIL / STRIP

of sheets, angle iron and extrusions.

HOLE PUNCHING UNITS, GAUGES & BOLTS

HOLE PUNCHING UNITS, GAUGES & BOLTS

PILOT PIN & HOLD DOWN HOLES

Keyed Mounting Template Non-Keyed Mounting Template

A dedicated setup on a keyed A dedicated setup on a non-keyed mounting template

Ph: (800) 828-7061 • (715) 263-3900 • Email: [email protected] • Web: www.unipunch.com

holes on one side to accept unit

HOLE PUNCHING UNITS,

UNIPUNCHHOLES IN PARTS. FAST.

If the part is no longer required, the modular tooling can be disassembled

■ A Strip Template or 23/32"

punched and brake-

UNIPUNCHHOLES IN PARTS. FAST.

Part No. Length Weight

5019-24 24" 33 lbs.

Ph: (800) 828-7061 • (715) 263-3900 • Email: [email protected] • Web: www.unipunch.com

1⁄ 2-13 For 1⁄2-13 S.H.C.S.