Forged Flanges Catalog

FORGED STEEL FLANGES
1. Holes accurately drilled for ease of assembly.
2. Spot facing ensures seating of fasteners true and square.
3. Grain flow controlled for maximum strength.
4. Smooth accurate bore for unrestricted flow.
5. Machined bevel and land facilitate good welding.
6. All faces machined within tolerances to ensure true alignment.
7. Full identification of size, pressure class, material and heat code.
•2•
FORGED
STEEL FLANGES
INDEX
FLANGES CLASS 150 (PN20) to CLASS 2500 (PN 420)
Welding Neck, Slip-on,
Threaded, Socket Welding
Lap Joint, Blind ....................................................................................................Page 36
REDUCING FLANGES
Welding Neck, Threaded, Slip-on ........................................................................Page 18
ORIFICE FLANGES CLASS 300 - 1500 (PN 50-250)

Welding Neck, Slip-on, Threaded ........................................................................Page 24
LONG WELDING NECKS ..........................................................................................Page 33
LARGE DIAMETER FLANGES

Class 125 LW Slip-on ..........................................................................................Page 34
Class 125 Welding Neck, Slip-on, Blind ..............................................................Page 35
Class 250.............................................................................................................Page 36
Class 75...............................................................................................................Page 37
Class 175.............................................................................................................Page 38
Class 350.............................................................................................................Page 39
AWWA Class B, D, E, Slip-on..............................................................................Page 40
Class 150 Series A ASME B16.47 ......................................................................Page 41
Class 150 Series B ASME B16.47 ......................................................................Page 46
ENGINEERING AND DESIGN DATA

Bolt and Stud Dimensions ...................................................................................Page 22
Flange Facing Dimensions ..................................................................................Page 20
Flange Facing and Finish Data .............................................................................Page 4
Gasket Dimensions .............................................................................................Page 20
Identification, Marking..........................................................................................Page 47
Manufacturing Standards, Specifications ..............................................................Page 5
Materials ................................................................................................................Page 5
Ring Joint Dimensions.........................................................................................Page 30
Tolerances ...........................................................................................................Page 47
Welding Bevels ....................................................................................................Page 48
•3•
FLANGE TYPES, FACINGS AND FINISHES
ANSI FLANGES
Most forged steel flanges correspond to the requirements of the American Standards Association (ASME/ANSI Standard B16.5)
and the ASTM Specification A-105.
The following types are manufactured and stocked:
Welding Neck flanges, available in all pressure ratings and sizes, are butt-welded to the end of the pipe, and are usually specified
when service conditions are severe and excellent workmanship necessary. Since the inside diameter of the flange must match
that of the pipe, the flange bore should be specified in ordering.
Slip-on flanges, also available in most pressure ratings and sizes, are a popular type due to their ease of application. This flange
slips over the end of the pipe and is usually set so that the flange face is about .375" (9.5mm) beyond the end of the pipe. This
permits double-welding of the flange - one strength fillet weld to join the hub of the flange to the pipe, and a seal fillet weld inside
the flange at the end of the pipe. Where operating conditions permit, the seal weld is omitted.
Slip-on flanges are most frequently used at lower pressure - Class 150 (PN 20) or Class 300 (PN 50) primary service pressure
ratings. Many pipe designers are reluctant to use slip-ons for higher pressures, since (1) the joint between the flange and pipe is
not as strong as in the welding neck type; and (2) the junction of the flange and pipe is more susceptible to corrosion.
Screwed or Threaded flanges are attached to the pipe like any other screwed fittings, and may be back-welded to seal the joint
between pipe and flange. Although still available in most sizes and pressure ratings, screwed fittings today are used almost
exclusively in smaller pipe sizes and at low pressures.
Lap Joint or Van Stone flanges are used on piping equipped with lap joint stub ends or with lapped pipe. They may be used at all
pressures and are available in a full size range. These flanges slip over the pipe, and are not welded or otherwise fastened to it;
bolting pressure is transmitted to the gasket by the pressure of the flange against the back of the pipe lap.
Lap Joint flanges have certain special advantages: (1) freedom to swivel around the pipe facilitates the lining up of opposing flange
bolt holes; (2) lack of contact with the fluid in the pipe often permits the use of inexpensive carbon steel flanges with corrosion
resistant pipe or tubing; (3) in systems which erode or corrode quickly, the flanges may be salvaged for re-use.
Socket-welding flanges contain a recess in the back of the flange to receive the end of the pipe, which is attached by a fillet weld
around the hub of the flange. Since socket-welding connections are not as strong as butt-welded joints, the use of this type of
flange is almost always confined to NPS 4 (DN 100) and smaller sizes, and to the lower pressure ratings. Its chief advantage lies
in the ease of preparation and installation.
Blind flanges, available in all sizes and pressure ratings, are solid forgings used to close off the end of a piping system and to
gain easy access to the interior of the line.
Reducing flanges are available. Refer to page 18.
FLANGE FACINGS
Unless otherwise specified, Class 150 (PN 20) and Class 300 (PN 50) flanges in all types except lap joint (or Van Stone) flanges
are furnished with a .06" (1.6mm) raised face (which is included in the flange thickness dimension). Heaver pressure ratings are
machined with a .25" (6.4 mm) raised face, in addition to the designated flange thickness.
When so ordered, these flange types can be furnished with a variety of other facings, such as male and female, ring joint, tongue
and groove, etc.
Lap Joint flanges are machined with a flat face and a fillet radius to accommodate the stub end or pipe lap.
FLANGE FINISHES
The finish of contact faces of pipe flanges and connecting end flanges of fittings shall be judged by visual comparison with AARH
Standards and not by instruments having stylus tracers and electronic amplification (see ANSI/ASME B46.1)
The finishes required are given below. Other finishes may be furnished upon application.
RAISED FACE AND LARGE MALE AND FEMALE: Either a serrated-concentric or serrated-spiral finish having from 45 to 55
grooves per inch (0.6 to 1mm pitch) shall be used. The cutting tool employed shall have an approximate 0.06" (1.6mm) or larger
radius. The resultant surface shall have a 125 to 250 microinch roughness.
TONGUE AND GROOVE AND SMALL MALE AND FEMALE: The gasket contact shall not exceed 125 microinch roughness.
RING JOINT: The side wall surface of gasket groove shall not exceed 63 microinch roughness.
OTHER TYPES
In addition to the ANSI flanges, the following types are carried in stock:
Orifice flanges are used for measuring fluid flow in piping systems. Their design conforms to the recommendations of the
American Gas Association’s Committee on Gas Measurement. Commonly furnished as either welding neck or slip-on type, they
may also be ordered as screwed flanges. Orifice unions are available in Class 300 (PN 50) and heavier pressure ratings.
Each Orifice flange is equipped with two radially-drilled, tapped holes for metering, and with jack-screws to facilitate separation
of the joint for removal of the orifice metering plate. Orifice flanges, unless otherwise specified, are furnished in pairs as a flange
union, complete with bolts, nuts and jack-screws - but without the orifice plate. Gaskets are supplied with raised face flange
unions, but not for ring-joint faced flanges, which use an integral gasket and orifice plate.
Light Weight Slip-on flanges, drilled to Class 125 ANSI Standards but of lighter construction than the regular slip-on type, are
available for low-pressure systems.
Large Diameter flanges, in sizes beyond the B16.5 range, are available for special installations. Dimensions given herein are those
most commonly used; however, flanges and rolled rings for large diameter pipe or for vessels and tanks can readily be made to
other specifications.
Long Welding Necks are used primarily for outlets for vessels and tanks. Drilled to ANSI Standards, they are forged with long,
heavy-wall, straight hubs, and finished with square cut ends.
•4•
MATERIAL AND
MANUFACTURING
STANDARDS
The manufacturing of forged steel flanges is governed by industry standards written by (1) the American Society for Testing and
Materials (ASTM); (2) the American National Standards Institute (ANSI); (3) the Manufacturer’s Standardization Society of the Valve
and Fittings Industry (MSS); (4) the American Petroleum Institute (API); (5) the Canadian Standards Association (CSA); (6) the
American Society of Mechanical Engineers (ASME); and (7) the Pipe Fabrication Institute (PFI). They cover specifications for
materials, methods of manufacture, dimensions and quality control procedures. CCTF forged steel flanges conform to all applicable
standards.
ASTM SPECIFICATIONS
ASTM specifications are, basically, materials specifications. They regulate approved raw materials from which flanges can be
made - ingots, or blooms, billets, slabs or bars. In addition, they govern the methods of manufacture, quality control procedures
and markings of forged steel flanges. ASTM specifications are divided into five categories:
A105 - Carbon grades for high temperature service
A181 - Carbon grades for general service
* A182 - Alloy and stainless grades for high temperature service
A350 - Carbon and alloy grades for low temperature service
*CCTF flanges are available in a wide range of alloy and stainless steels, including grades F304, F304L, F316, F316L. Please
refer to CCTF catalogue “Stainless Steel Flanges” for the popular Classes 150 and 300 (PN 20 and 50).
MSS, API, AWWA, ANSI AND CSA STANDARDS

ANSI, MSS and API standards govern flange dimensions and tolerances. ASME/ANSI B16.5, titled “Steel Pipe Flanges and
Flanged Fittings”, is the basic standard. It covers forged steel flanges, sizes NPS 1/2 (DN 15) through NPS 24 (DN 600). CSA
standard CAN3-Z245 12-M96 covers the manufacture, dimensions, tolerances and material requirements for pipe line flanges.
ASME/ANSI B16.36 covers Orifice flanges. The following MSS, API and AWWA standards are written to supplement B16.5:
MSS SP-6: Flange facings
MSS SP-9: Spot facing for bronze, iron and steel flanges
MSS SP-25: Marking of flanges
MSS SP-39: Bolts and nuts for flanges
API6A: Wellhead equipment
AWWA C207: Hub flanges
The following codes are not flange specifications, but they influences the manufacture of forged steel flanges:
ASME: Boiler and Pressure Vessel Code
ASME/ANSI B31.1: Power Piping
ASME/ANSI B31.3: Petroleum and refinery piping
ASME/ANSI B31.4: Liquid petroleum transportation piping systems
ASME/ANSI B31.5: Refrigeration piping
ASME/ANSI B31.8: Gas transmission and distribution piping systems
ANSI/ASME B36.10M: Standard for wrought steel pipe
ANSI/ASME B36.19M: Standard for stainless steel pipe
ANSI/ASME B16.47: Large diameter pipe line flanges NPS 22 (DN 550) and NPS 26 (DN 650) through NPS 36 (DN900)
METRIC EQUIVALENTS
The International System (SI) metric equivalent of British units are shown throughout this catalogue.
NPS (Nominal Pipe Size) = DN* (Nominal Diameter)
Operating Pressure Class = PN* (Pressure Number)
1 inch = 25.4 millimetres
1 pound, weight = 0.4536 kilograms
1 pound, pressure = 0.06895 bars
1 p.s.i., stress = 0.006895 megapascals (MPa)
*From the SI designations, Diamètre Nominal and Pression Nominale.
•5•
BORE LENGTH TRU HUB 2
WELDING SLIP-ON &
FLANGE FLANGE2 RAISED NECK & SOCKET WELD LAP SLIP-ON,
OUTSIDE THICKNESS FACE SOCKET SOCKET JOINT WELDING THREADED & LAP
NPS DIAMETER MIN. DIA. WELDING MIN. MIN. NECK SOCK. WELD JOINT
DN O T A B3 C D F G H
1/2 3.50 .44 1.38 .62 .88 .90 1.88 .62 .62
15 89 11.5 34.9 15.8 22.2 22.9 47.6 16 16
3/4 3.88 .50 1.69 .82 1.09 1.11 2.06 .62 .62
20 98 13.0 42.9 20.8 27.8 28.2 52.4 16 16
1 4.25 .56 2.00 1.05 1.36 1.38 2.19 .69 .69
25 108 14.5 50.8 26.7 34.5 34.9 55.6 17 17
1 1/4 4.62 .62 2.50 1.38 1.70 1.72 2.25 .81 .81
32 117 16.0 63.5 35.1 43.2 43.7 57.1 21 21
1 1/2 5.00 .69 2.88 1.61 1.95 1.97 2.44 .88 .88
40 127 17.5 73.0 40.9 49.5 50.0 61.9 22 22
2 6.00 .75 3.62 2.07 2.44 2.46 2.50 1.00 1.00
50 152 19.5 92.1 52.6 61.9 62.5 63.5 25 25
2 1/2 7.00 .88 4.12 2.47 2.94 2.97 2.75 1.12 1.12
65 178 22.5 104.8 62.7 74.6 75.4 69.8 29 29
3 7.50 .94 5.00 3.07 3.57 3.60 2.75 1.19 1.19
80 191 24.0 127.0 78.0 90.7 91.4 69.8 30 30
3 1/2 8.50 .94 5.50 3.55 4.07 4.10 2.81 1.25 1.25
90 216 24.0 139.7 90.2 103.4 104.1 71.4 32 32
4 9.00 .94 61.9 4.03 4.57 4.60 3.00 1.31 1.31
100 229 24.0 157.2 102.4 116.1 116.8 76.2 33 33
5 10.00 .94 7.31 5.05 5.66 5.69 3.50 1.44 1.44
125 254 24.0 185.7 128.3 143.7 144.5 88.9 36 36
6 11.00 1.00 8.50 6.07 6.72 6.75 3.50 1.56 1.56
150 279 25.5 215.9 154.2 170.7 171.4 88.9 40 40
8 13.50 1.12 10.62 7.98 8.72 8.75 4.00 1.75 1.75
200 343 29.0 269.9 202.7 221.5 222.2 101.6 44 44
10 16.00 1.19 12.75 10.02 10.88 10.92 4.00 1.94 1.94
250 406 30.5 323.8 254.5 276.2 277.4 101.6 49 49
12 19.00 1.25 15.00 12.00 12.88 12.92 4.50 2.19 2.19
300 483 32.0 381.0 304.8 327.0 328.2 114.3 56 56
14 21.00 1.38 16.25 14.14 14.18 5.00 2.25 3.12
350 535 35.0 412.8 359.2 360.2 127.0 57 79
To be
16 23.50 1.44 18.50 16.16 16.19 5.00 2.50 3.44
400 595 37.0 469.9 410.4 411.2 127.0 64 87
specified
18 25.00 1.56 21.00 18.18 18.20 5.50 2.69 3.81
450 635 40.0 533.4 461.8 462.3 139.7 68 97
by
20 27.50 1.69 23.00 20.20 20.25 5.69 2.88 4.06
500 700 43.0 584.2 purchaser 513.1 514.3 144.5 73 103
24 32.00 1.88 27.25 24.25 24.25 6.00 3.25 4.38
600 815 48.0 692.2 615.9 615.9 152.4 83 111
1
Socket Welding Flanges, sizes NPS 3 1/2 (DN 90) and larger are not
covered by ASME/ANSI B16.5.
2
Includes .06" (1.6 mm) raised face.
3
These dimensions correspond to inside diameters of pipe as given in
ANSI/ASME B36.10M for Standard Wall Pipe. Thickness of Standard
Wall is the same as Schedule 40 in size NPS 10 (DN 250) and smaller. INCHES
•6• MILLIMETRES
CLASS 150 (PN20)
FLANGES
FORGED STEEL
ASTM A-105
1
ASME/ANSI B16.5
DRILLING DIAMETER OF HUB APPROXIMATE WEIGHT

DEPTH1 LAP SLIP-ON,
DIA. OF OF JOINT THREADED &
NO. OF DIA. OF BOLT SOCKET AT AT FILLET WELDING SOCKET LAP
NPS HOLES HOLES CIRCLE BASE CHAMFER RADIUS NECK WELDING1 BLIND JOINT
DN J K L M N r
1/2 4 .62 2.38 .38 1.19 .84 .12 2 1 1 1
15 4 16 60.3 10 30.2 21.4 3 0.9 .05 0.5 0.5
3/4 4 .62 2.75 .44 1.50 1.05 .12 2 2 2 2
20 4 16 69.8 11 38.1 26.6 3 0.9 0.9 0.9 0.9
1 4 .62 3.12 .50 1.94 1.32 .12 3 2 2 2
25 4 16 79.4 13 49.2 33.5 3 1.4 0.9 0.9 0.9
1 1/4 4 .62 3.50 .56 2.31 1.66 .19 3 3 3 3
32 4 16 88.9 14 58.7 42.1 5 1.4 1.4 1.4 1.4
1 1/2 4 .62 3.88 .62 2.56 1.90 .25 4 3 4 3
40 4 16 98.4 16 65.1 48.3 6 1.8 1.4 1.8 1.4
2 4 .75 4.75 .69 3.06 2.38 .31 6 5 5 5
50 4 20 120.6 17 77.6 60.4 8 2.7 2.3 2.3 2.3
2 1/2 4 .75 5.50 .75 3.56 2.88 .31 8 7 7 7
65 4 20 139.7 19 90.5 73.0 8 3.6 3.2 3.2 3.2
3 4 .75 6.00 .81 4.25 3.50 .38 10 8 9 8
80 4 20 152.4 21 107.9 88.9 10 4.5 3.6 4.1 3.6
3 1/2 8 .75 7.00 - 4.81 4.00 .38 12 11 13 11
90 8 20 177.8 - 122.2 101.6 10 5.4 5.0 5.9 5.0
4 8 .75 7.50 - 5.31 4.50 .44 15 13 17 13
100 8 20 190.5 - 134.9 114.3 11 6.8 5.9 7.7 5.9
5 8 .88 8.50 - 6.44 5.56 .44 19 15 20 15
125 8 23 215.9 - 163.5 141.3 11 8.6 6.8 9.1 6.8
6 8 .88 9.50 - 7.56 6.63 .50 24 19 26 19
150 8 23 241.3 - 192.1 168.3 13 10.9 8.6 11.8 8.6
8 8 .88 11.75 - 9.69 8.63 .50 39 30 45 30
200 8 23 298.4 - 246.1 219.1 13 17.7 13.6 20.4 13.6
10 12 1.00 14.25 - 12.00 10.75 .50 52 43 70 43
250 12 26 361.9 - 304.8 273.0 13 23.6 19.5 31.8 19.5
12 12 1.00 17.00 - 14.38 12.75 .50 80 64 110 64
300 12 26 431.8 - 365.1 323.8 13 36.3 29.0 49.9 29.0
14 12 1.12 18.75 - 15.75 14.00 .50 110 90 140 105
350 12 29 476.2 - 400.0 355.6 13 50.0 41.0 63.5 47.6
16 16 1.12 21.25 - 18.00 16.00 .50 140 98 180 140
400 16 29 539.7 - 457.2 406.4 13 64.0 44.5 81.6 63.5
18 16 1.25 22.75 - 19.88 18.00 .50 150 130 220 160
450 16 32 577.8 - 504.8 457.2 13 68.0 59.0 99.8 72.6
20 20 1.25 25.00 - 22.00 20.00 .50 180 165 285 195
500 20 32 635.0 - 558.8 508.0 13 81.6 75.0 129.0 88.5
24 20 1.38 29.50 - 26.12 24.00 .50 260 220 430 275
600 20 35 749.3 - 663.6 609.6 13 118 99.8 195.0 125.0
For bevel of Welding Neck, see page 48.

Gasket dimensions - page 20.
Bolting dimensions - page 22.
POUNDS Flange facing dimensions - page 20.
KILOGRAMS •7•
BORE LENGTH THRU HUB 2
WELDING SLIP-ON & THREADED
FLANGE FLANGE2 RAISED NECK & SOCKET WELD LAP COUNTER- SLIP-ON,
OUTSIDE THICKNESS FACE SOCKET SOCKET JOINT BORE WELDING THREADED & LAP
NPS DIAMETER MIN. DIA. WELDING MIN. MIN. MIN. NECK SOCK. WELD JOINT
DN O T A B3 C D E F G H
1/2 3.75 .56 1.38 .62 .88 .90 .93 2.06 .88 .88
15 95 14.5 34.9 15.8 22.2 22.9 23.5 52.4 22 22
3/4 4.62 .62 1.69 .82 1.09 1.11 1.14 2.25 1.00 1.00
20 117 16.0 42.9 20.8 27.8 28.2 29.0 57.1 25 25
1 4.88 .69 2.00 1.05 1.36 1.38 1.41 2.44 1.06 1.06
25 124 17.5 50.8 26.6 34.5 34.9 36.0 61.9 27 27
1 1/4 5.25 .75 2.50 1.38 1.70 1.72 1.75 2.56 1.06 1.06
32 133 19.5 63.5 35.1 43.3 43.7 44.5 65.1 27 27
1 1/2 6.12 .81 2.88 1.61 1.95 1.97 1.99 2.69 1.19 1.19
40 156 21.0 73.0 40.9 49.6 50.0 50.5 68.3 30 30
2 6.50 .88 3.62 2.07 2.44 2.46 2.50 2.75 1.31 1.31
50 165 22.5 92.1 52.6 61.9 62.5 63.5 69.8 33 33
2 1/2 7.50 1.00 4.12 2.47 2.94 2.97 3.00 3.00 1.50 1.50
65 191 25.5 104.8 62.7 74.6 75.4 76 76.2 38 38
3 8.25 1.12 5.00 3.07 3.57 3.60 3.63 3.12 1.69 1.69
80 210 29.0 127.0 77.9 90.7 91.4 92 79.4 43 43
3 1/2 9.0 1.19 5.50 3.55 4.07 4.10 4.13 3.19 1.75 1.75
90 229 30.5 139.7 90.1 103.4 104.1 105 81.0 44 44
4 10.0 1.25 6.19 4.03 4.57 4.60 4.63 3.38 1.88 1.88
100 254 32.0 157.2 102.3 116.1 116.8 118 85.7 48 48
5 11.0 1.38 7.31 5.05 5.66 5.69 5.69 3.88 2.00 2.00
125 279 35.0 185.7 128.2 143.7 144.5 145 98.4 51 51
6 12.5 1.44 8.50 6.07 6.72 6.75 6.75 3.88 2.06 2.06
150 318 37.0 215.9 154.1 170.7 171.4 171 98.4 52 52
8 15.0 1.62 10.62 7.98 8.72 8.75 8.75 4.38 2.44 2.44
200 381 41.5 269.9 202.7 221.5 222.2 222 111.1 62 62
10 17.5 1.88 12.75 10.02 10.88 10.92 10.88 4.62 2.62 3.75
250 445 48.0 323.8 254.5 276.2 277.4 276 117.5 67 95
12 20.5 2.00 15.00 12.00 12.88 12.92 12.94 5.12 2.88 4.00
300 520 51.0 381.0 304.8 327.0 328.2 329 130.2 73 102
14 23.0 2.12 16.25 14.14 14.18 14.19 5.62 3.00 4.38
350 585 54.0 412.8 359.2 360.2 360 142.9 76 111
To be
16 25.5 2.25 18.50 16.16 16.19 16.19 5.75 3.25 4.75
400 650 57.5 469.9 410.4 411.2 411 146.0 83 121
specified
18 28.0 2.38 21.00 18.18 18.20 18.19 6.25 3.50 5.12
450 710 60.5 533.4 461.8 462.3 462 158.7 89 130
by
20 30.5 2.50 23.00 20.20 20.25 20.19 6.38 3.75 5.50
500 775 63.5 584.2 purchaser 513.1 514.3 513 161.9 95 140
24 36.0 2.75 27.25 24.25 24.25 24.19 6.62 4.19 6.00
600 915 70.0 692.2 615.9 615.9 614 168.3 106 152
1
2
3
These dimensions correspond to inside diameters of pipe as given in
ANSI/ASME B36.10M for Standard Wall Pipe. Thickness of Standard
Wall is the same as Schedule 40 in size NPS 10 (DN 250) and smaller. INCHES
•8• MILLIMETRES
CLASS 300 (PN50)
FLANGES
FORGED STEEL
ASTM A-105
1
ASME/ANSI B16.5

DEPTH1 LAP
DIA. OF OF JOINT SLIP-ON,
NO. OF DIA. OF BOLT SOCKET AT AT FILLET THREADED &
NPS HOLES HOLES CIRCLE BASE CHAMFER RADIUS WELDING SOCKET LAP
DN J K L M N r NECK WELDING1 BLIND JOINT
1/2 4 .62 2.62 .38 1.50 .84 .12 2 2 2 2
15 4 16 66.7 10 38.1 21.4 3 0.9 0.9 0.9 0.9
3/4 4 .75 3.25 .44 1.88 1.05 .12 3 3 3 3
20 4 20 82.5 11 47.6 26.6 3 1.4 1.4 1.4 1.4
1 4 .75 3.50 .50 2.12 1.32 .12 4 3 3 3
25 4 .20 88.9 13 53.8 33.5 3 1.8 1.4 1.4 1.4
1 1/4 4 .75 3.88 .56 2.50 1.66 .19 5 4 4 4
32 4 20 98.4 14 63.5 42.1 5 2.3 1.8 1.8 1.8
1 1/2 4 .88 4.50 .62 2.75 1.90 .25 7 6 6 6
40 4 23 114.3 16 69.9 48.3 6 3.2 2.7 2.7 2.7
2 8 .75 5.00 .69 3.31 2.38 .31 9 7 8 7
50 8 20 127.0 17 84.1 60.3 8 4.1 3.2 3.6 3.2
2 1/2 8 .88 5.88 .75 3.94 2.88 .31 12 10 12 10
65 8 23 149.2 19 100.0 73.0 8 5.4 4.5 5.4 4.5
3 8 .88 6.62 .81 4.62 3.50 .38 15 13 16 13
80 8 23 168.3 21 117.5 88.9 10 6.8 5.9 7.3 5.9
3 1/2 8 .88 7.25 - 5.25 4.00 .38 18 17 21 17
90 8 23 184.1 - 133.3 101.6 10 8.2 7.7 9.5 7.7
4 8 .88 7.88 - 5.75 4.50 .44 25 22 27 22
100 8 23 200.0 - 146.0 114.3 11 11.3 10.0 12.2 10.0
5 8 .88 9.25 - 7.00 5.56 .44 32 28 35 28
125 8 23 234.9 - 177.8 141.3 11 14.5 12.7 15.9 12.7
6 12 .88 10.62 - 8.12 6.63 .50 42 39 50 39
150 12 23 269.9 - 206.4 168.3 13 19.0 17.7 22.7 17.7
8 12 1.00 13.0 - 10.25 8.63 .50 67 58 81 58
200 12 26 330.2 - 260.3 219.1 13 30.4 26.3 36.7 26.3
10 16 1.12 15.25 - 12.62 10.75 .50 91 81 125 91
250 16 29 387.3 - 320.7 273.0 13 41.3 36.7 56.7 41.3
12 16 1.25 17.75 - 14.75 12.75 .50 140 115 185 140
300 16 32 450.8 - 374.6 323.8 13 63.5 52.2 83.9 63.5
14 20 1.25 20.25 - 16.75 14.00 .50 180 165 250 190
350 20 32 514.3 - 425.5 355.6 13 81.6 74.8 113 86.2
16 20 1.38 22.50 - 19.00 16.00 .50 250 190 295 250
400 20 35 571.5 - 482.6 406.4 13 113 86.2 134 113
18 24 1.38 24.75 - 21.00 18.00 .50 320 250 395 295
450 24 35 628.6 - 533.4 457.2 13 145 113 179 134
20 24 1.38 27.00 - 23.12 20.00 .50 400 315 505 370
500 24 35 685.80 - 587.4 508.0 13 181 143 229 168
24 24 1.62 32.00 - 27.62 24.00 .50 580 475 790 550
600 24 42 812.80 - 701.7 609.6 13 263 215 358 249
1
POUNDS Flange facing dimensions - page 20.
KILOGRAMS •9•
For sizes NPS 1/2 (DN 15) through NPS 3 1/2 (DN 90) use Class 600 (PN 100) flanges. 1
THREADED
FLANGE FLANGE2 RAISED LAP COUNTER-
OUTSIDE THICKNESS FACE WELDING SLIP-ON, JOINT BORE WELDING SLIP-ON, LAP
NPS DIAMETER MIN. DIA. NECK MIN. MIN. MIN. NECK THREADED JOINT
DN O T A B C D E F G H
4 10 1.38 6.19 4.57 4.60 4.63 3.5 2 2
100 254 35.0 157.2 116.1 116.8 118 88.9 51 51
5 11 1.50 7.31 5.66 5.69 5.69 4 2.12 2.12
125 279 38.5 185.7 143.7 144.5 145 101.6 54 54
6 12.5 1.62 8.5 6.72 6.75 6.75 4.06 2.25 2.25
150 318 41.5 215.9 170.7 171.4 171 103.2 57 57
8 15 1.88 10.62 8.72 8.75 8.75 4.62 2.69 2.69
200 381 48.0 269.9 To be 221.5 222.2 222 117.5 68 68
10 17.5 2.12 12.75 10.88 10.92 10.88 4.88 2.88 4
250 445 54.0 323.8 specified 276.2 277.4 276 123.8 73 102
12 20.5 2.25 15.00 12.88 12.92 12.94 5.38 3.12 4.25
300 520 57.5 381.0 by 327.0 328.2 329 136.5 79 108
14 23 2.38 16.25 14.14 14.18 14.19 5.88 3.31 4.62
350 585 60.5 412.8 purchaser 359.2 360.2 360 149.2 84 117
16 25.5 2.5 18.50 16.16 16.19 16.19 6 3.69 5
400 650 63.5 469.9 410.4 411.2 411 152.4 94 127
18 28 2.62 21 18.18 18.20 18.19 6.5 3.88 5.38
450 710 67.0 533.4 461.8 462.3 462 165.1 98 137
20 30.5 2.75 23 20.20 20.25 20.19 6.62 4 5.75
500 775 70.0 584.2 513.1 514.3 513 168.3 102 146
24 36 3 27.25 24.25 24.25 24.19 6.88 4.5 6.25
600 915 76.5 692.2 616.0 616.0 614 174.6 114 159
1
Including SOCKET WELDING FLANGES
2
Does not include .25" (6.4 mm) raised face.
INCHES
• 10 • MILLIMETRES
CLASS 400 (PN 68)
FLANGES
FORGED STEEL
ASTM A-105
ASME/ANSI B16.5

DIAMETER LAP
DIAMETER OF JOINT
NO. OF OF BOLT AT AT FILLET
NPS HOLES HOLES CIRCLE BASE CHAMFER RADIUS WELDING SLIP-ON, LAP
DN J K M N r NECK THREADED BLIND JOINT
4 8 1 7.88 5.75 4.50 .44 35 26 33 25
100 8 26 200.0 146.0 114.3 11 15.8 11.7 15 11.3
5 8 1 9.25 7.0 5.56 .44 43 31 44 29
125 8 26 234.9 177.8 141.3 11 19 14 20 13
6 12 1 10.62 8.12 6.63 .5 57 44 61 42
150 12 26 269.9 206.4 168.3 13 25.5 20 27.5 19
8 12 1.12 13.0 10.25 8.63 .5 89 67 100 64
200 12 29 330.2 260.3 219.1 13 40 30 45 29
10 16 1.25 15.25 12.62 10.75 .5 126 91 155 112
250 16 32 387.3 320.7 273.0 13 57 41 70 50
12 16 1.38 17.75 14.75 12.75 .5 177 129 226 152
300 16 35 450.8 374.7 323.8 13 80 58 102 68
14 20 1.38 20.25 16.75 14.00 .5 233 191 310 210
350 20 35 514.3 425.5 355.6 13 105 86 140 95
16 20 1.5 22.5 19.0 16.00 .5 294 253 398 280
400 20 39 571.5 482.6 406.4 13 132 114 179 126
18 24 1.5 24.75 21.0 18.00 .5 360 310 502 345
450 24 39 628.7 533.4 457.2 13 162 140 226 155
20 24 1.62 27 23.12 20.00 .5 445 378 621 420
500 24 42 685.8 587.4 508.0 13 200 170 279 189
24 24 1.88 32 27.62 24.00 .5 640 539 936 615
600 24 48 812.8 701.7 609.6 13 288 243 421 277
Flange facing dimensions - page 20.
POUNDS
KILOGRAMS • 11 •
WELDING SLIP-ON & THREADED SLIP-ON,
FLANGE FLANGE2 RAISED NECK & 1
SOCK. WELD. LAP COUNTER- THREADED
OUTSIDE THICKNESS FACE 1
SOCKET SOCKET JOINT BORE WELDING 1
SOCKET LAP
NPS DIAMETER MIN. DIA. WELDING MIN. MIN. MIN. NECK WELDING JOINT
1/2 3.75 .56 1.38 .88 .90 .93 2.06 .88 .88
15 95 14.5 34.9 22.2 22.9 23.5 52.4 22 22
3/4 4.62 .62 1.69 1.09 1.11 1.14 2.25 1.00 1.0
20 117 16.0 42.9 27.8 28.2 29.0 57.1 25 25
1 4.88 .69 2.0 1.36 1.38 1.41 2.44 1.06 1.06
25 124 17.5 50.8 34.5 34.9 36.0 61.9 27 27
1 1/4 5.25 .81 2.5 1.70 1.72 1.75 2.62 1.12 1.12
32 133 21.0 63.5 43.3 43.7 44.5 66.7 29 29
1 1/2 6.12 .88 2.88 1.95 1.97 1.99 2.75 1.25 1.25
40 156 22.5 73.0 49.6 50.0 50.5 69.8 32 32
2 6.5 1.0 3.62 2.44 2.46 2.50 2.88 1.44 1.44
50 165 25.5 92.1 61.9 62.5 63.5 73.0 37 37
2 1/2 7.5 1.12 4.12 2.94 2.97 3.00 3.12 1.62 1.62
65 191 29.0 104.8 74.6 75.4 76.0 79.4 41 41
3 8.25 1.25 5.0 3.57 3.60 3.63 3.25 1.81 1.81
80 210 32.0 127.0 90.7 91.4 92.0 82.5 46 46
3 1/2 9.0 1.38 5.5 To be 4.07 4.10 4.13 3.38 1.94 1.94
90 229 35.0 139.7 103.4 104.1 105 85.7 49 49
4 10.75 1.5 6.19 specified 4.57 4.60 4.63 4.0 2.12 2.12
100 273 38.5 157.2 116.1 116.8 118 101.6 54 54
5 13.0 1.75 7.31 by 5.66 5.69 5.69 4.5 2.38 2.38
125 330 44.5 185.7 143.7 144.5 145 114.3 60 60
6 14.0 1.88 8.5 purchaser 6.72 6.75 6.75 4.62 2.62 2.62
150 356 48.0 215.9 170.7 171.4 171 117.3 67 67
8 16.5 2.19 10.62 8.72 8.75 8.75 5.25 3.0 3.0
200 419 55.5 269.9 221.5 22.22 222 133.3 76 76
10 20.0 2.5 12.75 10.88 10.92 10.88 6.0 3.38 4.38
250 510 63.5 323.8 276.2 277.4 276 152.4 86 111
12 22.0 2.62 15.0 12.88 12.92 12.94 6.12 3.62 4.62
300 560 66.5 381.0 327.0 328.2 329 155.6 92 117
14 23.75 2.75 16.25 14.14 14.18 14.19 6.5 3.69 5.0
350 605 70.0 412.8 359.2 360.2 360 165.1 94 127
16 27.0 3.0 18.5 16.16 16.19 16.19 7.0 4.19 5.5
400 685 76.5 469.9 410.4 411.2 411 177.5 106 140
18 29.25 3.25 21.0 18.18 18.20 18.19 7.25 4.62 6.0
450 745 83.0 533.4 461.8 462.3 462 184.1 117 152
20 32.0 3.5 23.0 20.20 20.25 20.19 7.5 5.0 6.4
500 815 89.0 584.2 513.1 514.3 513 190.5 127 165
24 37.0 4.0 27.25 24.25 24.25 24.19 8.0 5.5 7.25
600 940 102.0 692.2 615.9 615.9 614 203.2 140 184
1
Socket Welding Flanges, sizes NPS 3 1/2 (DN 90) and
larger are not covered by ASME/ANSI B16.5.
2
INCHES
CLASS 600 (PN 100)
FLANGES
FORGED STEEL
ASTM A-105
1
ASME/ANSI B16.5

1
DEPTH LAP
DIA. OF OF JOINT SLIP-ON,
NPS HOLES HOLES CIRCLE BASE CHAMFER RADIUS WELDING SOCKET LAP
DN J K L M N r NECK WELDING1 BLIND JOINT
1/2 4 .62 2.62 .38 1.5 .84 .12 2 2 2 2
15 4 16 66.7 10 38.1 21.4 3 0.9 0.9 0.9 0.9
3/4 4 .75 3.25 .44 1.88 1.05 .12 4 3 3 3
20 4 20 82.5 11 47.6 26.6 3 1.8 1.4 1.4 1.4
1 4 .75 3.5 .50 2.12 1.32 .12 4 4 4 4
25 4 .20 88.9 13 54.0 33.5 3 1.8 1.8 1.8 1.8
1 1/4 4 .75 3.88 .56 2.5 1.66 .19 6 5 5 5
32 4 20 98.4 14 63.9 42.1 5 2.7 2.3 2.3 2.3
1 1/2 4 .88 4.5 .62 2.75 1.90 .25 8 7 8 7
40 4 23 114.3 16 69.8 48.3 6 3.6 3.2 3.6 3.2
2 8 .75 5.0 .69 3.31 2.38 .31 12 9 10 9
50 8 20 127.0 17 84.1 60.3 8 5.4 4.1 4.5 4.1
2 1/2 8 .88 5.88 .75 3.94 2.88 .31 18 13 15 12
65 8 23 149.2 19 100.0 73.0 8 8.2 5.9 6.8 5.4
3 8 .88 6.62 .81 4.62 3.50 .38 23 16 20 15
80 8 23 168.3 21 117.5 88.9 10 10.4 7.3 9.1 6.8
3 1/2 8 1.0 7.25 - 5.25 4.00 .38 26 21 29 20
90 8 26 184.1 - 133.3 101.6 10 11.8 9.5 13.2 9.1
4 8 1.0 8.5 - 6.0 4.50 .44 42 37 41 36
100 8 26 215.9 - 152.4 114.3 11 19.0 16.8 18.6 16.3
5 8 1.12 10.5 - 7.44 5.56 .44 68 63 68 61
125 8 29 266.7 - 188.9 141.3 11 31.0 28.6 30.8 27.7
6 12 1.12 11.5 - 8.75 6.63 .50 81 80 86 78
150 12 29 292.1 - 222.2 168.3 13 36.7 36.3 39.0 35.4
8 12 1.25 13.75 - 10.75 8.63 .50 120 115 140 110
200 12 32 349.2 - 273.0 219.1 13 54.4 52.2 63.5 49.9
10 16 1.38 17.0 - 13.5 10.75 .50 190 170 230 170
250 16 35 431.8 - 342.9 273.0 13 86.2 77.1 104 77.2
12 20 1.38 19.25 - 15.75 12.75 .50 225 200 295 200
300 20 35 488.9 - 400.0 323.8 13 102 90.7 134 90.7
14 20 1.50 20.75 - 17.0 14.0 .50 280 230 355 250
350 20 39 527.0 - 431.8 355.6 13 127 104 161 113
16 20 1.62 23.75 - 19.5 16.0 .50 390 330 495 365
400 20 42 603.2 - 495.2 406.4 13 177 150 225 166
18 20 1.75 25.75 - 21.5 18.0 .50 475 400 630 435
450 20 45 654.0 - 546.1 457.2 13 215 181 286 197
20 24 1.75 28.5 - 24.0 20.0 .50 590 510 810 570
500 24 45 723.9 - 609.6 508.0 13 268 231 367 259
24 24 2.0 33.0 - 28.25 24.0 .50 830 730 1250 810
600 24 51 838.2 - 717.5 609.6 13 376 331 567 367
POUNDS
THREADED
FLANGE FLANGE2 RAISED LAP COUNTER-
OUTSIDE THICKNESS FACE WELDING SLIP-ON, JOINT BORE WELDING SLIP-ON, LAP
NPS DIAMETER MIN. DIA. NECK MIN. MIN. MIN. NECK THREADED JOINT
3 9.50 1.50 5.00 3.57 3.60 3.63 4.00 2.12 2.12
80 241 38.5 127.0 90.7 91.4 92 101.6 54 54
4 11.50 1.75 6.19 4.57 4.60 4.63 4.50 2.75 2.75
100 292 44.5 157.2 q 116.1 116.8 118 114.3 70 70
5 13.75 2.0 7.31 5.66 5.69 5.69 5.00 3.12 3.12
125 349 51.0 185.7 143.7 144.5 145 127.0 79 79
6 15.00 2.19 8.50 6.72 6.75 6.75 5.50 3.38 3.38
150 381 56.0 215.9 170.7 171.4 171 139.7 86 86
8 18.50 2.5 10.62 8.72 8.75 8.75 67.38 4.00 4.50
To be
200 470 63.5 269.9 221.5 222.2 222 161.9 102 114
10 21.50 2.75 12.75 specified 10.88 10.92 10.88 7.25 4.25 5.00
250 545 70.0 323.8 276.2 277.4 276 184.2 108 127
12 24.00 3.12 15.00 by 12.88 12.92 12.94 7.88 4.62 5.62
300 610 79.5 381.0 327.0 328.2 329 200.0 117 143
14 25.25 3.38 16.25 purchaser 14.14 14.18 14.19 8.38 5.12 6.12
350 640 86.0 412.8 359.2 360.2 360 212.7 130 156
16 27.75 3.5 18.50 16.16 16.19 16.19 8.50 5.25 6.50
400 705 89.0 469.9 410.4 411.2 411 215.9 133 165
18 31.00 4.0 21.00 18.18 18.20 18.19 9.00 6.00 7.50
450 785 102.0 533.4 461.8 462.3 462 228.8 152 191
20 33.75 4.25 23.00 20.20 20.25 20.19 9.75 6.25 8.25
500 855 108.0 584.2 513.1 514.3 513 247.6 159 210
24 41.00 5.5 27.25 24.25 24.25 24.19 11.50 8.00 10.50
600 1040 140.0 692.2 615.9 615.9 614 292.1 203 267
1
Including SOCKET WELDING FLANGES
2
INCHES
CLASS 900 (PN 150)
FLANGES
FORGED STEEL
ASTM A-105
ASME/ANSI B16.5
DIAMETER LAP
DIAMETER OF JOINT
NO. OF OF BOLT AT AT FILLET
NPS HOLES HOLES CIRCLE BASE CHAMFER RADIUS WELDING SLIP-ON, LAP
DN J K M N r NECK THREADED BLIND JOINT
3 8 1.00 7.50 5.00 3.50 .38 .31 31 31 47
80 8 26 190.5 127.0 88.9 10 14.1 14.1 14.1 21.3
4 8 1.25 9.25 6.25 4.50 .44 51 53 54 51
100 8 32 234.9 158.7 114.3 11 23.1 24.0 24.5 23.1
5 8 1.38 11.00 7.50 5.56 .44 86 83 87 81
125 8 35 279.4 190.5 141.3 11 39.0 37.6 39.5 36.7
6 12 1.25 12.50 9.25 6.63 .50 110 110 115 105
150 12 32 317.5 234.9 168.3 13 49.9 49.9 52.2 47.6
8 12 1.50 15.50 11.75 8.63 .50 175 170 200 190
200 12 39 393.7 298.4 219.1 13 79.4 77.1 90.7 86.2
10 16 1.50 18.50 14.50 10.75 .50 260 245 290 275
250 16 39 469.9 368.3 273.0 13 118 111 132 125
12 20 1.50 21.00 16.50 12.75 .50 325 325 415 370
300 20 39 533.4 419.1 323.8 13 147 147 188 168
14 20 1.62 22.00 17.75 14.00 .50 400 400 520 415
350 20 42 558.8 450.8 355.6 13 181 181 236 188
16 20 1.75 24.25 20.00 16.00 .50 495 425 600 465
400 20 45 615.9 508.0 406.4 13 225 193 272 211
18 20 2.00 27.00 22.25 18.00 .50 680 600 850 650
450 20 51 685.8 565.1 457.2 13 308 272 386 295
20 20 2.12 29.50 24.50 20.00 .50 830 730 1075 810
500 20 54 749.3 622.3 508.0 13 376 331 488 367
24 20 2.62 35.50 29.5 24.00 .50 1500 1400 2025 1550
600 20 67 901.7 749.3 609.6 13 680 635 918 703

POUNDS
WELDING 1
SLIP-ON & THREADED 1
SLIP-ON,
FLANGE FLANGE2 RAISED NECK & 1
SOCK. WELD. LAP COUNTER- THREADED,
OUTSIDE THICKNESS FACE 1
SOCKET SOCKET JOINT BORE WELDING 1
SOCKET LAP
NPS DIAMETER MIN. DIA. WELDING MIN. MIN. MIN. NECK WELDING JOINT
1/2 4.75 .88 1.38 0.88 .90 .93 2.38 1.25 1.25
15 121 22.5 34.9 22.2 22.9 23.5 60.3 32 32
3/4 5.12 1.00 1.69 1.09 1.11 1.14 2.75 1.38 1.38
20 130 25.5 42.9 27.8 28.2 29.0 69.8 35 35
1 5.88 1.12 2.00 1.36 1.38 1.41 2.88 1.62 1.62
25 149 29.0 50.8 34.5 34.9 36.0 73.0 41 41
1 1/4 6.25 1.12 2.50 1.70 1.72 1.75 2.88 1.62 1.62
32 159 29.0 63.5 43.3 43.7 44.5 73.0 41 41
1 1/2 7.00 1.25 2.88 1.95 1.97 1.99 3.25 1.75 1.75
40 178 32.0 73.0 49.6 50.0 50.5 82.5 44 44
2 8.50 1.50 3.62 2.44 2.46 2.50 4.00 2.25 2.25
50 216 38.5 92.1 61.9 62.5 63.5 101.6 57 57
2 1/2 9.62 1.62 4.12 2.94 2.97 3.00 4.12 2.50 2.50
65 244 41.5 104.8 74.6 75.4 76.0 104.8 64 64
3 10.50 1.88 5.00 - 3.60 3.63 4.62 2.88 2.88
80 267 48.0 127.0 To be - 91.4 92.0 117.5 73 73
4 12.25 2.12 6.19 - 4.60 4.63 4.88 3.56 3.56
100 311 54.0 157.2 specified - 116.8 118 123.8 90 90
5 14.75 2.88 7.31 - 5.69 5.69 6.12 4.12 4.12
125 375 73.5 185.7 by - 144.5 145 155.6 105 105
6 15.50 3.25 8.50 - 6.75 6.75 6.75 4.69 4.69
150 394 83.0 215.9 purchaser - 171.4 171 171.4 119 119
8 19.00 3.62 10.62 - 8.75 8.75 8.38 5.62 5.62
200 483 92.0 269.9 - 222.2 222 212.7 143 143
10 23.00 4.25 12.75 - 10.92 10.88 10.00 6.25 7.00
250 585 108.0 323.8 - 277.4 276 254.0 159 178
12 26.50 4.88 15.00 - 12.92 12.94 11.12 7.12 8.62
300 675 124.0 381.0 - 328.2 329 282.6 181 219
14 29.50 5.25 16.25 - 14.18 - 11.75 - 9.50
350 750 133.5 412.8 - 360.2 - 298.4 - 241
16 32.50 5.75 18.50 - 16.19 - 12.25 - 10.25
400 825 146.5 469.9 - 411.2 - 311.1 - 260
18 36.00 6.38 21.00 - 18.20 - 12.88 - 10.88
450 915 162.0 533.4 - 462.3 - 327.0 - 276
20 38.75 7.00 23.00 - 20.25 - 14.00 - 11.50
500 985 178.0 584.2 - 514.3 - 355.6 - 292
24 46.00 8.00 27.25 - 24.25 - 16.00 - 13.00
600 1170 203.5 692.2 - 615.9 - 406.4 - 330
1
Socket Welding and Slip-on Flanges, size NPS 3 1/2 (DN 80)
and larger are not covered by ASME/ANSI B16.5.
2
INCHES
CLASS 1500 (PN 250)
FLANGES
FORGED STEEL
ASTM A-105
ASME/ANSI B16.5

1
DEPTH LAP
DIA. OF OF JOINT 1
SLIP-ON,
NPS HOLES HOLES CIRCLE BASE CHAMFER RADIUS WELDING 1
SOCKET LAP
DN J K L M N r NECK WELDING BLIND JOINT
1/2 4 .88 3.25 .38 1.50 .84 .12 5 4 4 4
15 4 23 82.5 10 38.1 21.4 3 2.3 1.8 1.8 1.8
3/4 4 .88 3.50 .44 1.75 1.05 .12 6 5 6 5
20 4 23 88.9 11 44.4 26.6 3 2.7 2.3 2.7 2.3
1 4 1.00 4.00 .50 2.06 1.32 .12 9 8 8 8
25 4 26 101.6 13 52.4 33.5 3 4.1 3.6 3.6 3.6
1 1/4 4 1.00 4.38 .56 2.50 1.66 .19 10 9 9 9
32 4 26 111.1 14 63.5 42.1 5 4.5 4.1 4.1 4.1
1 1/2 4 1.12 4.88 .62 2.75 1.90 .25 13 12 13 12
40 4 29 123.8 16 69.8 48.3 6 5.9 5.4 5.9 5.4
2 8 1.00 6.50 .69 4.12 2.38 .31 25 25 25 25
50 8 26 165.1 17 104.8 60.3 8 11.3 11.3 11.3 11.3
2 1/2 8 1.12 7.50 .75 4.88 2.88 .31 36 36 35 35
65 8 29 190.5 19 123.8 73.0 8 16.3 16.3 15.9 16.0
3 8 1.25 8.00 - 5.25 3.50 .38 48 48 48 47
80 8 32 203.2 - 133.3 88.9 10 21.8 21.8 21.8 21.3
4 8 1.38 9.50 - 6.38 4.50 .44 73 73 73 75
100 8 35 241.3 - 161.9 114.3 11 33.1 33.1 33.1 34.0
5 8 1.62 11.50 - 7.75 5.56 .44 130 130 140 140
125 8 42 292.1 - 196.8 141.3 11 59.0 59.0 63.5 63.5
6 12 1.50 12.50 - 9.00 6.63 .50 165 165 160 170
150 12 39 317.5 - 228.6 168.3 13 75 75 72.6 77.1
8 12 1.75 15.50 - 11.50 8.63 .50 275 260 300 285
200 12 45 393.7 - 292.1 219.1 13 125 118 136 129
10 12 2.00 19.00 - 14.50 10.75 .50 455 435 510 485
250 12 51 482.6 - 368.3 273.0 13 206 197 231 220
12 16 2.12 22.50 - 17.75 12.75 .50 690 580 690 630
300 16 54 571.5 - 450.6 323.8 13 313 263 313 286
14 16 2.38 25.00 - 19.50 14.00 .50 940 - 975 890
350 16 61 635.0 - 495.3 355.6 13 426 - 442 404
16 16 2.62 27.75 - 21.75 16.00 .50 1250 - 1300 1150
400 16 67 704.8 - 552.4 406.4 13 567 - 590 522
18 16 2.88 30.50 - 23.50 18.00 .50 1625 - 1750 1475
450 16 74 774.7 - 569.9 457.2 13 737 - 795 669
20 16 3.12 32.75 - 25.25 20.00 .50 2050 - 2225 1775
500 16 80 831.8 - 641.3 508.0 13 930 - 1010 805
24 16 3.62 39.00 - 30.00 24.00 .50 3325 - 3625 2825
600 16 92 990.6 - 762.0 609.6 13 1510 - 1644 1326

POUNDS
WELDING SLIP-ON2 & THREADED SLIP-ON2
FLANGE RAISED NECK & SOCK. WELD.2 LAP COUNTER- THREADED
OUTSIDE FLANGE1 FACE SOCKET2 SOCKET JOINT BORE WELDING SOCKET2 LAP
NPS DIAMETER THICKNESS DIA. WELDING MIN. MIN. MIN. NECK WELDING JOINT
1/2 5.25 1.19 1.38 0.88 .90 0.93 2.88 1.56 1.56
15 133 30.5 34.9 22.2 22.9 23.5 73.0 40 40
3/4 5.50 1.25 1.69 1.09 1.11 1.14 3.12 1.69 1.69
20 140 32.0 42.9 27.8 28.2 29.0 79.4 43 43
1 6.25 1.38 2.00 1.36 1.38 1.41 3.50 1.88 1.88
25 159 35.0 50.8 34.5 34.9 36.0 88.9 48 48
1 1/4 7.25 1.50 2.50 1.70 1.72 1.75 3.75 2.06 2.06
32 184 38.5 63.5 43.3 43.7 44.5 95.2 52 52
1 1/2 8.00 1.75 2.88 1.95 1.97 1.99 4.38 2.38 2.38
40 203 44.5 73.0 49.6 50.0 50.5 111.4 60 60
2 9.25 2.00 3.62 To be 2.44 2.46 2.50 5.00 2.75 2.75
50 235 51.0 92.1 61.9 62.5 63.5 127.0 70 70
2 1/2 10.50 2.25 4.12 specified 2.94 2.97 3.00 5.62 3.12 3.12
65 267 57.5 104.8 74.6 75.4 76 142.9 79 79
3 12.00 2.62 5.00 by 3.57 3.60 3.63 6.62 3.62 3.62
80 305 67.0 127.0 90.7 91.4 92 168.2 92 92
4 14.00 3.00 6.19 purchaser 4.57 4.60 4.63 7.50 4.25 4.25
100 356 76.5 157.2 116.1 116.8 118 190.5 108 108
5 16.50 3.62 7.31 5.66 5.69 5.69 9.00 5.12 5.12
125 419 92.5 185.7 143.7 144.5 145 228.6 130 130
6 19.00 4.25 8.50 6.72 6.75 6.75 10.75 6.0 6.0
150 483 108.0 215.9 170.7 171.4 171 273.0 152 152
8 21.75 5.00 10.62 8.72 8.75 8.75 12.50 7.0 7.0
200 552 127.0 269.9 221.5 222.2 222 317.5 178 178
10 26.50 6.50 12.75 10.88 10.92 10.88 16.50 9.0 9.0
250 675 165.5 323.8 276.2 277.4 276 419.4 229 229
12 30.00 7.25 15.00 12.88 12.92 12.94 18.25 10.0 10.0
300 760 184.5 381.0 327.0 328.2 329 463.6 254 254
1
Dimensions do not include .25" (6.4 mm) raised face.
2
Class 2500 (PN 420) Socket Welding and Slip-on Flanges not covered by ANSI B16.5
REDUCING FLANGES ASME/ANSI B16.5 —

Hub dimensions shall be at least as large as those of the facing dimensions, shall be the same as those of a
standard flanges of the size to which the reduction is being standard flange of the nominal pipe size from which the
made, except that flanges reduced to a size smaller than reduction is being made.
those shown in the accompanying table may be used
Reducing flanges are specified by giving firstly the size
without hubs.
from which the reduction is made, followed by the reduced
For threaded flanges, tapped smaller than the reduced size size.
in the table, Blind Flanges may be used.
Example: NPS 6 x 4 Class 300 reducing threaded flange.
Flange thickness, outside diameter, drilling template and (DN 150 x 100, PN 50 reducing threaded flange.)
INCHES
CLASS 2500 (PN 420)
FLANGES*
FORGED STEEL
ASTM A-105
1
ASME/ANSI B16.5

DEPTH LAP
DIA. OF OF JOINT SLIP-ON,2
NO. OF DIA. OF BOLT 2
SOCKET AT AT FILLET THREADED &
NPS HOLES HOLES CIRCLE BASE CHAMFER RADIUS WELDING SOCKET2 LAP
DN J K L M N r NECK WELDING BLIND JOINT
1/2 4 .88 3.50 .38 1.69 .84 .12 7 7 7 7
15 4 23 88.9 10 42.9 21.4 3 3.2 3.2 3.2 3.2
3/4 4 .88 3.75 .44 2.00 1.05 .12 8 8 8 8
20 4 23 95.2 11 50.8 26.6 3 3.6 3.6 3.6 3.6
1 4 1.00 4.25 .50 2.25 1.32 .12 12 11 11 11
25 4 26 107.9 13 57.1 33.5 3 5.4 5.0 5.0 5.0
1 1/4 4 1.12 5.12 .56 2.88 1.66 .19 17 16 17 16
32 4 29 130.2 14 73.0 42.1 5 7.7 7.3 7.7 7.3
1 1/2 4 1.25 5.75 .62 3.12 1.90 .25 25 22 23 22
40 4 32 146.0 16 79.4 48.3 6 11.3 10 10.4 10
2 8 1.12 6.75 .69 3.75 2.38 .31 42 38 39 37
50 8 29 171.4 17 95.2 60.3 8 19.0 17.2 17.7 16.8
2 1/2 8 1.25 7.75 .75 4.50 2.88 .31 52 55 56 53
65 8 32 196.8 19.0 114.3 73.0 8 23.6 24.9 25.4 24
3 8 1.38 9.00 - 5.25 3.50 .38 94 83 86 80
80 8 35 228.6 - 133.3 88.9 10 42.6 37.6 39 36.3
4 8 1.62 10.75 - 6.50 4.50 .44 145 125 135 120
100 8 42 273.0 - 165.1 114.3 11 65.8 56.7 61.2 54.4
5 8 1.88 12.75 - 8.00 5.56 .44 245 210 225 205
125 8 48 323.8 - 203.2 141.3 11 111 95.3 102 93.0
6 8 2.12 14.50 - 9.25 6.63 .50 380 325 345 315
150 8 54 368.3 - 234.9 168.3 13 172 147 156 143
8 12 2.12 17.25 - 12.00 8.63 .50 580 485 530 470
200 12 54 438.1 - 304.8 219.1 13 263 220 240 213
10 12 2.62 21.25 - 14.75 10.75 .50 1075 930 1025 900
250 12 67 539.7 - 374.8 273.0 13 488 422 465 408
12 12 2.88 24.38 - 17.38 12.75 .50 1525 1100 1300 1100
300 12 74 619.1 - 441.3 323.8 13 692 499 590 499
* Class 2500 (PN 420) Socket Welding and Slip-on Flanges are not covered by ASME/ANSI B16.5.
Bevel of Welding Neck, see page 48
Flange facing and gasket dimensions, see page 20.
Bolting dimensions, see page 22.
CLASS 150 — 2500 (PN 20 - 420)

Smallest Size of Smallest Size of Smallest Size of
Nominal Reducing Outlet Nominal Reducing Outlet Nominal Reducing Outlet
Pipe Size DN Requiring Hub Flanges Pipe Size DN Requiring Hub Flanges Pipe Size DN Requiring Hub Flanges
1 25 1/2 3 1/2 90 1 1/2 12 300 3 1/2
1 1/4 32 1/2 4 100 1 1/2 14 350 3 1/2
1 1/2 40 1/2 5 125 1 1/2 16 400 4
2 50 1 6 150 2 1/2 18 450 4
2 1/2 65 1 1/4 8 200 3 1/2 20 500 4
3 80 1 1/4 10 250 3 1/2 24 600 4
POUNDS Reducing Flanges are generally supplied as Slip-on or Threaded; however Reducing Welding Neck flanges are available
by special order.
FLANGE
FACING
AND
GASKET
DIMENSIONS
RAISED FACE, FLAT FACE, LAP JOINT
*FLANGE FACING GASKET DIMENSIONS
RAISED FLAT RING
FACE, FLAT FLAT RING TYPE GASKET FULL OR FULL
LAP JOINT FACE (EXTENDING TO INSIDES OF BOLTS) FACE FACE
OUTSIDE DIAMETER TYPE TYPES
NPS O. DIA. O. DIA. OUTSIDE INSIDE
DN A O CL. 150 CL. 300 CL. 400 CL. 600 CL. 900 CL. 1500 CL. 2500 DIAMETER DIAMETER
1/2 1.38 1.88 2.12 2.12 2.12 2.50 2.50 2.75 0.84
15 35 48 54 54 54 64 64 70 21
3/4 1.69 2.25 2.62 2.62 2.62 2.75 2.75 3.00 1.06
20 43 57 67 67 67 70 70 76 27
1 2 2.62 2.88 2.88 2.88 3.12 3.12 3.38 1.31
25 51 67 73 73 73 79 79 86 33
1 1/4 2.5 3.00 3.25 3.25 3.25 3.50 3.50 4.12 1.66
32 64 76 83 83 83 89 89 105 42
1 1/2 2.88 3.38 3.75 3.75 3.75 3.88 3.88 4.62 1.91
40 73 86 95 95 95 98 98 117 49
2 3.62 4.12 4.38 4.38 4.38 5.62 5.62 5.75 2.38
Same as flange outside diameter, see pages 6 - 19.
Same as flange outside diameter, see pages 6 - 19.

50 92 105 111 111 111 143 143 146 60
2 1/2 4.12 4.88 5.12 5.12 5.12 6.50 6.50 6.62 2.88
65 105 124 130 130 130 165 165 168 73
3 5 5.38 5.88 5.88 5.88 6.62 6.88 7.75 3.5
80 127 137 149 149 149 168 175 197 89
3 1/2 5.5 6.38 6.50 6.38 6.38 - - - 4
90 140 162 165 162 162 - - - 102
4 6.19 6.88 7.12 7.00 7.62 8.12 8.25 9.25 4.5
100 157 175 181 178 194 206 210 235 114
5 7.31 7.75 8.50 8.38 9.50 9.75 10.00 11.00 5.56
125 185 197 216 213 241 248 254 279 141
6 8.5 8.75 9.88 9.75 10.50 11.38 11.12 12.50 6.62
150 216 222 251 248 267 289 2.83 318 168
8 10.62 11.00 12.12 12.00 12.62 14.12 13.88 15.25 8.62
200 270 279 308 305 321 359 352 387 219
10 12.75 13.38 14.25 14.12 15.75 17.12 17.12 18.75 10.75
250 324 340 362 359 400 435 435 476 273
12 15 16.12 16.62 16.50 18.00 19.62 20.50 21.62 12.75
300 381 410 422 419 457 498 520 550 324
14 16.25 17.75 19.12 19.00 19.38 20.50 22.75 - 14
350 413 451 486 483 492 520 580 - 356
16 18.5 20.25 21.25 21.12 22.25 22.62 25.25 - 16
400 470 51 515 540 537 565 575 640 - 407
18 21 21.62 23.50 23.38 24.12 25.12 27.75 - 18
450 533 550 595 595 615 640 705 - 457
20 23 23.88 25.75 25.50 26.88 27.50 29.75 - 20
500 584 605 655 648 685 700 755 - 508
24 27.25 28.25 30.5 30.25 31.12 33.00 35.50 - 24
600 692 718 775 770 790 839 902 - 610
Gasket Facing is indicated on the facing drawings by “GF”.
Dimensions conform to ASME/ANSI B16.5 and ANSI B16.21, where applicable.
* A tolerance of ±0.16" (0.44 mm) is allowed on the inside and outside diameters of all facings.
INCHES
∆ For Ring Joint dimensions see page 30.
FLANGE
FACING
AND
GASKET
DIMENSIONS
MALE & FEMALE,
TONGUE & GROOVE
*FLANGE FACINGS DIMENSIONS GASKET DIMENSIONS
OUTSIDE DIAMETER INSIDE DIAMETER OUTSIDE DIAMETER INSIDE DIAMETER
LARGE LARGE LARGE LARGE LARGE
MALE; FEMALE; TONGUE; GROOVE; MALE &
LARGE SMALL SMALL LARGE SMALL SMALL SMALL SMALL FEMALE. LARGE OR
TONGUE MALE TONGUE GROOVE FEMALE GROOVE TONGUE GROOVE LARGE SMALL SMALL LARGE SMALL
NPS TONGUE & MALE & TONGUE & MALE & TONGUE &
DN A B C D E F G H GROOVE FEMALE GROOVE FEMALE GROOVE
1/2 1.38 0.72 1.38 1.44 0.78 1.44 1.00 0.94 1.38 0.72 1.38 0.84 1.00
15 35 18.3 35.0 36.5 19.9 36.5 25.4 23.8 35 18.3 35.0 21 25
3/4 1.69 .94 1.69 1.75 1.00 1.75 1.31 1.25 1.69 .94 1.69 1.06 1.31
20 43 23.8 42.9 44.5 25.4 44.4 33.3 31.8 43 23.8 42.9 27 33
1 2.00 1.19 1.88 2.06 1.25 1.94 1.5 1.44 2.00 1.19 1.88 1.31 1.50
25 51 30.2 47.6 52.4 31.8 49.2 38.1 36.5 51 30.2 47.6 33 38
1 1/4 2.50 1.5 2.25 2.56 1.56 2.31 1.88 1.81 2.50 1.50 2.25 1.66 1.88
32 64 38.1 57.2 65.1 39.7 58.7 47.6 46.0 64 38.1 57.2 42 48
1 1/2 2.88 1.75 2.50 2.94 1.81 2.56 2.12 2.06 2.88 1.75 2.50 1.91 2.12
40 73 44.4 63.5 74.6 46.0 65.1 54.0 52.4 73 44.4 63.5 49 54
2 3.62 2.25 3.25 3.69 2.31 3.31 2.88 2.81 3.62 2.25 3.25 2.38 2.88
50 92 57.2 82.6 93.7 58.7 84.1 73.0 71.4 92 57.2 82.6 60 73
2 1/2 4.12 2.69 3.75 4.19 2.75 3.81 3.38 3.31 4.12 2.69 3.75 2.88 3.38
65 105 68.3 95.2 106.4 69.9 96.8 85.7 84.1 105 68.3 95.2 73 86
3 5.00 3.31 4.62 5.06 3.38 4.69 4.25 4.19 5.00 3.31 4.62 3.5 4.25
80 127 84.1 117.5 128.6 85.7 119.1 108.0 106.4 127 84.1 117.5 89 108
3 1/2 5.50 3.81 5.12 5.56 3.88 5.19 4.75 4.69 5.50 3.81 5.12 4 4.75
90 140 96.8 130.2 141.3 98.4 131.8 120.6 119.1 140 96.8 130.2 102 121
4 6.19 4.31 5.69 6.25 4.38 5.75 5.19 5.12 6.19 4.31 5.69 4.5 5.19
100 157 109.5 144.5 158.8 111.1 146.0 131.8 130.2 157 109.5 144.5 114 132
5 7.31 5.38 6.81 7.38 5.44 6.88 6.31 6.25 7.31 5.38 6.81 5.56 6.31
125 185 136.5 173.0 187.3 138.1 174.6 160.3 158.8 185 136.5 173.0 141 161
6 8.50 6.38 8.00 8.56 6.44 8.06 7.5 7.44 8.50 6.38 8.00 6.62 7.50
150 216 161.9 203.2 217.5 163.5 204.8 190.5 188.9 216 161.9 203.2 168 191
8 10.62 8.38 10.00 10.69 8.44 10.06 9.38 9.31 10.62 8.38 10.00 8.62 9.38
200 270 212.7 254.0 271.5 214.3 255.6 238.1 236.5 270 212.7 254.0 219 238
10 12.75 10.5 12.00 12.81 10.56 12.06 11.25 11.19 12.75 10.50 12.00 10.75 11.25
250 324 266.7 304.8 325.4 268.3 306.4 285.8 284.2 324 266.7 304.8 273 286
12 15.0 12.5 14.25 15.06 12.56 14.31 13.5 13.44 15.00 12.50 14.25 12.75 13.50
300 381 317.5 362.0 382.6 319.1 363.5 342.9 341.3 381 317.5 362.0 324 343
14 16.25 13.75 15.50 16.31 13.81 15.56 14.75 14.69 16.25 13.75 15.50 14 14.75
350 413 349.2 393.7 414.3 350.8 395.3 374.6 373.1 413 349.2 393.7 356 375
16 18.5 15.75 17.62 18.56 15.81 17.69 16.75 16.69 18.50 15.75 17.62 16 16.75
400 470 400.0 447.7 471.5 401.6 449.3 425.4 423.9 470 400.0 447.7 407 426
18 21.0 17.75 20.12 21.06 17.81 20.19 19.25 19.19 21.00 17.75 20.12 18 19.25
450 533 450.9 511.2 535.0 452.4 512.8 489.0 487.4 533 450.9 511.2 457 489
20 23.0 19.75 22.0 23.06 19.81 22.06 21.0 20.94 23.00 19.75 22.0 20 21.00
500 584 501.7 558.8 585.8 503.2 560.4 533.4 531.8 584 501.7 558.8 510 535
24 27.25 23.75 26.25 27.41 23.81 26.31 25.25 25.19 27.25 23.75 26.25 24 25.25
600 692 603.3 666.8 693.7 604.8 668.3 641.4 639.8 692 603.3 666.8 610 640
Gasket Facing is indicated on the facing drawings by “GF”. ∆ For Ring Joint dimensions see page 30.
* A tolerance of ±0.16" (0.44 mm) is allowed on the inside and outside diameters of all facings.
Dimensions conform to ASME/ANSI B16.5 and ANSI B16.21, where
INCHES applicable.
MILLIMETRES • 21 •
BOLT AND
STUD
DIMENSIONS*
CONTINUED ON PAGE 23
CLASS 150 (PN 20) FLANGES CLASS 300 (PN 50) FLANGES CLASS 400 (PN 64) FLANGES
LENGTH LENGTH LENGTH OF
MACHINE MACHINE STUD BOLTS
STUD BOLTS BOLTS STUD BOLTS BOLTS
.06 .06 .06 .06 .25 MALE &
DIA. OF 1.6 1.6 DIA. OF 1.6 1.6 DIA. OF 6.4 FEMALE
NPS NO. OF BOLTS RAISED RING RAISED NO. OF BOLTS RAISED RING RAISED NO. OF BOLTS RAISED TONGUE & RING
DN BOLTS (inches) FACE JOINT FACE BOLTS (inches) FACE JOINT FACE BOLTS (inches) FACE GROOVE JOINT
1/2 4 1/2 2.50 - 2.00 4 1/2 2.75 3.00 2.25 4 1/2 3.25 3.00 3.00
15 4 1/2 65 - 50 4 1/2 70 75 55 4 1/2 85 75 75
3/4 4 1/2 2.50 - 2.25 4 5/8 3.00 3.50 2.50 4 5/8 3.50 3.25 3.50
20 4 1/2 65 - 55 4 5/8 75 90 6.5 4 5/8 90 85 90
1 4 1/2 2.75 3.25 2.25 4 5/8 3.25 3.75 2.75 4 5/8 3.75 3.50 3.75
25 4 1/2 70 85 55 4 5/8 85 95 70 4 5/8 95 90 95
1 1/4 4 1/2 2.75 3.25 2.50 4 5/8 3.25 3.75 2.75 4 5/8 4.00 3.75 4.00
32 4 1/2 70 85 65 4 5/8 85 95 70 4 5/8 100 95 100
1 1/2 4 1/2 3.00 3.50 2.50 4 3/4 3.75 4.25 3.00 4 3/4 4.25 4.00 4.25
40 4 1/2 75 90 65 4 3/4 95 110 75 4 3/4 110 100 110
2 4 5/8 3.25 3.75 2.75 8 5/8 3.50 4.25 3.00 8 5/8 4.25 4.00 4.50
50 4 5/8 85 95 70 8 5/8 90 110 75 8 5/8 110 100 115
2 1/2 4 5/8 3.50 4.00 3.00 8 3/4 4.00 4.75 3.50 8 3/4 4.75 4.50 5.00
65 4 5/8 90 100 75 8 3/4 100 120 90 8 3/4 120 115 130
3 4 5/8 3.75 4.25 3.25 8 3/4 4.25 5.00 3.75 8 3/4 5.00 4.75 5.25
80 4 5/8 95 110 85 8 3/4 110 125 95 8 3/4 130 120 135
3 1/2 8 5/8 3.75 4.25 3.25 8 3/4 4.50 5.25 3.75 8 7/8 5.50 5.25 5.75
90 8 5/8 95 110 85 8 3/4 115 135 95 8 7/8 140 135 145
4 8 5/8 3.75 4.25 3.25 8 3/4 4.50 5.25 4.00 8 7/8 5.50 5.25 5.75
100 8 5/8 95 110 85 8 3/4 115 135 100 8 7/8 140 135 145
5 8 3/4 4.00 4.50 3.25 8 3/4 4.75 5.50 4.25 8 7/8 5.75 5.50 6.00
125 8 3/4 100 115 85 8 3/4 120 140 110 8 7/8 145 140 155
6 8 3/4 4.00 4.50 3.50 12 3/4 5.00 5.75 4.25 12 7/8 6.00 5.75 6.25
150 8 3/4 100 115 90 12 3/4 130 145 110 12 7/8 155 145 160
8 8 3/4 4.25 4.75 3.75 12 7/8 5.50 6.25 4.75 12 1 6.75 6.50 7.00
200 8 3/4 110 120 95 12 7/8 140 160 120 12 1 175 165 180
10 12 7/8 4.75 5.25 4.00 16 1 6.25 7.00 5.50 16 1 1/8 7.50 7.25 7.75
250 12 7/8 120 135 100 16 1 160 180 140 16 1 1/8 190 185 195
12 12 7/8 4.75 5.25 4.25 16 1 1/8 6.75 7.50 6.00 16 1 1/4 8.00 7.75 8.25
300 12 7/8 120 135 110 16 1 1/8 175 190 155 16 1 1/4 205 195 210
14 12 1 5.25 4.75 4.50 20 1 1/8 7.00 7.75 6.25 20 1 1/4 8.25 8.00 8.50
350 12 1 135 145 115 20 1 1/8 180 195 160 20 1 1/4 210 205 215
16 16 1 5.50 6.00 4.75 20 1 1/4 7.50 8.25 6.50 20 1 3/8 8.75 8.50 9.00
400 16 1 140 155 120 20 1 1/4 190 210 165 20 1 3/8 225 215 230
18 16 1 1/8 6.00 6.50 5.00 24 1 1/4 7.75 8.50 6.75 24 1 3/8 9.00 8.75 9.25
450 16 1 1/8 150 165 125 24 1 1/4 195 215 175 24 1 3/8 230 225 235
20 20 1 1/8 6.25 6.75 5.50 24 1 1/4 8.25 9.00 7.25 24 1 1/2 9.75 9.50 10.00
500 20 1 1/8 160 175 140 24 1 1/4 210 230 185 24 1 1/2 250 240 255
24 20 1 1/4 7.00 7.50 6.00 24 1 1/2 9.25 10.25 8.00 24 1 3/4 10.75 10.50 11.25
600 20 1 1/4 180 190 155 24 1 1/2 235 260 205 24 1 3/4 275 265 285
* Length of Stud Bolt does not include the height of the points.
Bolt sizes are in inches.
Length of Male & Female and Tongue & Groove Stud Bolts are .25" (6.4 mm) less than those for the same size of .25"
(6.4 mm) Raised Face Stud Bolts.
INCHES
BOLT AND
STUD
DIMENSIONS
CONTINUED
CLASS 600 (PN 100) FLANGES CLASS 900 (PN 150) FLANGES CLASS 1500 (PN 250) FLANGES CLASS 2500 (PN 420) FLANGES
LENGTH OF LENGTH OF LENGTH OF LENGTH OF
STUD BOLTS STUD BOLTS STUD BOLTS STUD BOLTS
.25 .25 .25 .25

DIA. OF 6.4 DIA. OF 6.4 DIA. OF 6.4 DIA. OF 6.4
NPS NO. OF BOLTS RAISED RING NO. OF BOLTS RAISED RING NO. OF BOLTS RAISED RING NO. OF BOLTS RAISED RING
DN BOLTS (inches) FACE JOINT BOLTS (inches) FACE JOINT BOLTS (inches) FACE JOINT BOLTS (inches) FACE JOINT
1/2 4 1/2 3.25 3.00 4 3/4 4.25 4.25 4 3/4 4.25 4.25 4 3/4 5.25 5.25
15 4 1/2 85 75 4 3/4 110 110 4 3/4 110 110 4 3/4 135 135
3/4 4 5/8 3.50 3.50 4 3/4 4.50 4.50 4 3/4 4.50 450 4 3/4 5.25 5.25
20 4 5/8 90 90 4 3/4 115 115 4 3/4 115 115 4 3/4 135 135
1 4 5/8 3.75 3.75 4 7/8 5.00 5.00 4 7/8 5.00 5.00 4 7/8 5.75 5.75
25 4 5/8 95 95 4 7/8 125 125 4 7/8 125 125 4 7/8 145 145
1 1/4 4 5/8 4.00 4.00 4 7/8 5.00 5.00 4 7/8 5.00 5.00 4 1 6.25 6.50
32 4 5/8 100 100 4 7/8 125 125 4 7/8 125 125 4 1 160 165
1 1/2 4 3/4 4.25 4.25 4 1 5.50 5.50 4 1 5.50 5.50 4 1 1/8 7.00 7.25
40 4 3/4 110 110 4 1 140 140 4 1 140 140 4 1 1/8 180 185
2 8 5/8 4.25 4.50 8 7/8 5.75 5.75 8 7/8 5.75 5.75 8 1 7.25 7.50
50 8 5/8 110 115 8 7/8 145 145 8 7/8 145 145 8 1 185 190
2 1/2 8 3/4 4.75 5.00 8 1 6.25 6.25 8 1 6.25 6.25 8 1 1/8 8.00 8.25
65 8 3/4 120 125 8 1 160 160 8 1 160 160 8 1 1/8 205 210
3 8 3/4 5.00 5.25 8 7/8 5.75 6.00 8 1 1/8 7.00 7.00 8 1 1/4 9.00 9.25
80 8 3/4 130 135 8 7/8 145 155 8 1 1/8 180 180 8 1 1/4 230 235
3 1/2 8 7/8 5.50 5.75 - - - - - - - - - - - -
90 8 7/8 140 145 - - - - - - - - - - - -
4 8 7/8 5.75 6.00 8 1 1/8 6.75 7.00 8 1 1/4 7.75 7.75 8 1 1/2 10.25 10.75
100 8 7/8 145 155 8 1 1/8 175 180 8 1 1/4 195 195 8 1 1/2 260 275
5 8 1 6.50 6.75 8 1 1/4 7.50 7.75 8 1 1/2 9.75 9.75 8 1 3/4 12.00 12.75
125 8 1 165 175 8 1 1/4 190 195 8 1 1/2 250 250 8 1 3/4 305 325
6 12 1 6.75 7.00 12 1 1/8 7.75 7.75 12 1 3/8 10.25 10.50 8 2 13.75 14.50
150 12 1 175 180 12 1 1/8 195 195 12 1 3/8 260 265 8 2 350 370
8 12 1 1/8 7.75 7.75 12 1 3/8 8.75 9.00 12 1 5/8 11.50 12.00 12 2 15.25 16.00
200 12 1 1/8 195 195 12 1 3/8 225 230 12 1 5/8 295 305 12 2 390 405
10 16 1 1/4 8.50 8.75 16 1 3/8 9.25 9.50 12 1 7/8 13.25 13.75 12 2 1/2 19.50 20.50
250 16 1 1/4 215 225 16 1 3/8 235 240 12 1 7/8 335 350 12 2 1/2 495 520
12 20 1 1/4 8.75 9.00 20 1 3/8 10.00 10.25 16 2 14.75 15.50 12 2 3/4 21.50 22.50
300 20 1 1/4 225 230 20 1 3/8 255 260 16 2 375 395 12 2 3/4 545 570
14 20 1 3/8 9.25 9.50 20 1 1/2 10.75 11.25 16 2 1/4 16.00 17.00
350 20 1 3/8 235 240 20 1 1/2 275 285 16 2 1/4 405 430
16 20 1 1/2 10.00 10.25 20 1 5/8 11.25 11.75 16 2 1/2 17.50 18.50
400 20 1 1/2 255 260 20 1 5/8 285 300 16 2 1/2 445 470
18 20 1 5/8 10.75 11.00 20 1 7/8 12.75 13.50 16 2 3/4 19.50 20.50
450 20 1 5/8 275 280 20 1 7/8 325 345 16 2 3/4 495 520
20 24 1 5/8 11.50 11.75 20 2 13.50 14.25 16 3 21.50 22.50
500 24 1 5/8 295 300 20 2 345 360 16 3 545 570
24 24 1 7/8 13.00 13.25 20 2 1/2 17.25 18.00 16 3 1/2 24.50 25.75
600 24 1 7/8 330 335 20 2 1/2 440 455 16 3 1/2 620 655
* Length of Stud Bolt does not include the height of the points
Bolt sizes are in inches.
Length of Male & Female and Tongue & Groove Stud Bolts are .25" (6.4 mm) less than those for the same size of .25"
(6.4 mm) Raised Face Stud Bolts.
INCHES
BORE ∆
LENGTH TRU HUB
∆
FLANGE WELDING NECK SLIP-ON AND THREADED
FLANGE THICKNESS RAISED
OUTSIDE RAISED RING FACE WELDING SLIP-ON RAISED RING RAISED RING
NPS DIAMETER FACE JOINT DIAMETER NECK FACE JOINT FACE JOINT
DN O T T A B C F F G G
CLASS 300 (PN 50)
1 4.88 1.50 1.25 2.00 1.05 1.36 3.25 3.00 1.88 1.62
25 124 38.5 32.0 50.80 26.6 34.5 82.6 76.2 48 41.3
1 1/4 ■ 5.25 1.50 1.25 2.50 1.38 1.70 3.31 3.06 1.81 1.56
■ 32 133 38.5 32.0 63.50 35.1 43.2 84.1 77.8 46 39.7
1 1/2 6.12 1.50 1.25 2.88 1.61 1.95 3.38 3.12 1.88 1.62
40 156 38.5 32.0 73.05 40.9 49.5 85.8 79.4 48 41.3
2 6.50 1.50 1.25 3.62 2.07 2.44 3.38 3.12 1.94 1.69
50 165 38.5 32.0 92.10 52.5 62.0 85.8 79.4 49 42.9
2 1/2 7.50 1.50 1.25 4.12 2.47 2.94 3.50 3.25 2.00 1.75
65 191 38.5 32.0 104.80 62.7 74.5 88.9 82.6 51 44.5
3 8.25 1.50 1.25 5.00 3.07 3.57 3.50 3.25 2.06 1.81
80 210 38.5 32.0 127.00 77.9 90.5 88.9 82.6 52 46.0
4 10.0 1.50 1.25 6.19 4.03 4.57 3.62 3.38 2.12 1.88
100 254 38.5 32.0 157.20 102.3 116.0 92.1 85.7 54 47.6
5 ■ 11.0 1.50 1.38 7.31 5.05 5.66 4.00 3.88 2.12 2.00
■ 125 279 38.5 35.0 185.70 128.2 143.8 101.6 98.4 54 50.8
6 12.5 1.50 1.44 8.50 6.07 6.72 3.94 3.88 2.12 2.06
150 318 38.5 36.5 215.90 154.1 171.0 100.0 98.4 54 52.4
8 15.0 1.62 1.62 10.62 7.98 8.72 4.38 4.38 2.44 2.44
200 381 41.5 41.5 269.90 202.7 221.0 111.2 111.1 62 61.9
10 17.5 1.88 1.88 12.75 10.02 10.88 4.62 4.62 2.62 2.62
250 445 48.0 48.0 323.90 254.5 276.0 117.5 117.5 67 66.7
12 20.5 2.00 2.00 15.00 12.00 12.88 5.12 5.12 2.88 2.88
300 520 51.0 51.0 381.00 304.8 327.0 130.2 130.2 73 73.0
14 23.0 2.12 2.12 16.25 13.25 14.14 5.62 5.62 3.00 3.00
350 585 54.0 54.0 412.80 336.6 359.0 142.9 142.9 76 76.2
16 25.5 2.25 2.25 18.50 15.25 16.16 5.75 5.75 3.25 3.25
400 650 57.5 57.5 469.90 387.4 410.0 146.1 146.1 83 82.6
18 28.0 2.38 2.38 21.00 17.25 18.18 6.25 6.25 3.50 3.50
450 710 60.5 60.5 533.40 438.2 462.0 158.8 158.8 89 88.9
20 30.5 2.50 2.50 23.00 19.25 20.20 6.38 6.38 3.75 3.75
500 775 63.5 63.5 584.20 489.0 513.0 162.0 161.9 95 95.3
24 36.0 2.75 2.75 27.25 23.25 24.25 6.62 6.62 4.19 4.19
600 915 70.0 70.0 692.20 590.6 616.0 168.3 168.3 106 106.4
#ASME/ANSI B16.36 does not cover Class 300 Threaded Orifice Flanges in sizes above NPS 8 (DN 200).
■ Not included in ASME/ANSI B16.36.
*Details of Ring Joint facings are given on page 30.
FOR FURTHER DETAILS, REFER TO PAGE 4 “OTHER TYPES”.
∆ 0.06" (1.6 mm) Raised Face is included in Flange Thickness T, and length through Hub, F & G.
INCHES
CLASS 300 (PN 50)
FORGED
ORIFICE FLANGES
ASTM A-105
ASME/ANSI B16.36
DRILLING BOLTING DIAMETER APPROXIMATE WEIGHT

LENGTH OF HUB WELDING SLIP-ON AND
NECK THREADED
DIA. OF BOLT AT AT
NPS NO. OF DIA. OF BOLT DIA. RAISED RING BASE CHAMFER RAISED RING RAISED RING
DN HOLES HOLES CIRCLE (inches) FACE JOINT M N FACE JOINT FACE JOINT
CLASS 300 (PN 50)
1 4 0.69 3.50 5/8 4.00 4.75 2.12 1.32 18 20 15 17
25 4 18 89 5/8 102 121 54.0 33.5 8 9 7 7.5
1 1/4 ■ 4 0.69 3.88 5/8 4.00 4.75 2.50 1.66 21 23 17 20
■ 32 4 17.5 99 5/8 102 121 63.5 42.2 9.5 10.5 7.5 9
1 1/2 4 0.81 4.50 3/4 4.25 5.00 2.75 1.90 28 30 24 28
40 4 18 114 3/4 108 127 70 48.5 12.5 13.5 11 13
2 8 0.69 5.00 5/8 4.00 4.75 3.31 2.38 33 36 27 31
50 8 18 127 5/8 102 120 84 60.5 15 16 12 14
2 1/2 8 0.81 5.88 3/4 4.25 5.00 3.94 2.88 43 46 36 42
65 8 21 149 3/4 108 127 100 73.0 19.5 21 16 19
3 8 0.81 6.62 3/4 4.25 5.00 4.62 3.50 48 52 42 48
80 8 21 168 3/4 108 127 117 89.0 21.5 23.5 19 22
4 8 0.81 7.88 3/4 4.25 5.00 5.75 4.50 68 73 60 66
100 8 21 200 3/4 108 127 146 114.0 30.5 33 27 30
5 ■ 8 0.88 9.25 3/4 4.25 5.50 7.00 5.56 78 89 69 80
■ 125 8 23 235 3/4 108 140 178 141.2 35 40 31 36
6 12 0.88 10.62 3/4 4.25 5.50 8.12 6.63 100 115 94 110
150 12 23 270 3/4 108 140 206 168.0 45 52 42.5 50
8 12 1.00 13.00 7/8 4.50 6.00 10.25 8.63 155 180 135 160
200 12 26 330 7/8 115 153 260 219.0 70 81 61 73
10 16 1.12 15.25 1 5.50 6.50 12.62 10.75 220 255 200 230
250 16 29 387 1 140 165 321 273.0 99 115 90 104
12 16 1.25 17.75 1 1/8 5.50 7.00 14.75 12.75 330 380 280 325
300 16 32 451 1 1/8 140 178 375 324.0 149 171 125 147
14 20 1.25 20.25 1 1/8 6.00 7.00 16.75 14.00 425 485 395 450
350 20 32 514 1 1/8 153 178 425.5 356.0 191 218 178 204
16 20 1.38 22.50 1 1/4 6.50 8.00 19.00 16.00 590 660 465 535
400 20 35 572 1 1/4 165 204 483 406.0 266 297 209 243
18 24 1.38 24.75 1 1/4 6.50 8.00 21.00 18.00 750 830 610 690
450 24 35 629 1 1/4 165 204 535 457.0 338 374 275 313
20 24 1.38 27.00 1 1/4 7.00 8.00 23.12 20.00 910 1025 740 840
500 24 35 686 1 1/4 178 204 585 508.0 410 461 336 381
24 24 1.62 32.00 1 1/2 7.50 9.00 27.62 24.00 1350 1500 1125 1300
600 24 42 813 1 1/2 191 229 700 610.0 608 675 510 590
The tapped metering holes are drilled as follows:

1/2" for sizes NPS 4 (DN 100) and over
3/8" for sizes NPS 3 (DN 80)
1/4" for sizes NPS 1 1/2 (DN 65) and under.
POUNDS
†
CLASS 400 (PN 68)
BORE ∆
LENGTH TRU HUB
∆
4 10 1.38 1.38 6.19 4.57 3.5 3.5 2 2
100 254 35.0 35.0 157.2 116.1 88.9 88.9 50.8 50.8
5 ■ 11 1.50 1.50 7.31 As 5.66 4.0 4 2.12 2.12
■ 125 279 38.5 38.1 185.7 143.8 101.6 101.6 54.0 54.0
6 12.5 1.62 1.62 8.50 specified 6.72 4.06 4.06 2.25 2.25
150 318 41.5 41.5 215.9 170.7 103.2 103.2 57.2 57.2
8 15 1.88 1.88 10.62 by 8.72 4.62 4.62 2.69 2.69
200 381 48.0 48.0 269.9 221.5 117.5 117.4 68.3 68.3
10 17.5 2.12 2.12 12.75 10.88 4.88 4.88 2.88 2.88
purchaser
250 445 54.0 54.0 323.9 276.4 123.5 123.8 73.0 73.0
12 20.5 2.25 2.25 15.00 12.88 5.38 5.38 3.12 3.12
300 520 57.5 57.5 381.0 327.2 136.5 136.5 79.4 79.4
†
CLASS 600 (PN 100)
BORE ∆
LENGTH TRU HUB
∆
4 10.75 1.50 1.50 6.19 4.57 4.00 4.00 2.12 2.12
100 273 38.5 38.1 157.2 116.1 101.6 101.6 54.0 54.0
5 ■ 13.00 1.75 1.75 7.31 As 5.66 4.50 4.50 2.38 2.38
■ 125 330 44.5 44.5 185.7 143.8 114.3 114.3 60.5 60.5
6 14.00 1.88 1.88 8.50 specified 6.72 4.62 4.62 2.62 2.62
150 356 48.0 48.0 215.9 170.7 117.5 117.5 66.7 66.7
8 16.50 2.19 2.19 10.62 by 8.72 5.25 5.25 3.00 3.00
200 419 56.0 56.0 269.9 221.5 133.4 133.4 76.2 76.2
10 20.00 2.50 2.50 12.75 10.88 6.00 6.00 3.38 3.38
purchaser
250 510 63.5 63.5 323.9 276.4 152.4 152.4 85.7 85.7
12 22.00 2.62 2.62 15.00 12.88 6.12 6.12 3.62 3.62
300 560 67.0 67.0 381.0 327.2 155.6 155.6 92.1 92.1
∆ .25" (6.4 mm) Raised Face s not included in Flange Thickness T, and Length through Hub F & G.
† Flanges size NPS 3 (DN80) and smaller are identical to Class 300 flanges, except for bolting steel specifications, compliance with which then
permits their use for these higher Class ratings.
■ Not covered by ASME/ANSI B16.36.
# Welding Neck Orifice Flanges in sizes NPS 14 through 24 (DN 350 through 600), as covered by ASME/ANSI B16.36, are available upon
application.
* Details of Ring Joint facings are given on page 30.
FOR FURTHER DETAILS, REFER TO PAGE 4 “OTHER TYPES”. INCHES
CLASS 400 (PN 68)
CLASS 600 (PN 100)
FORGED
#
ORIFICE FLANGES
ASTM A-105
ASME/ANSI B16.36
ASME/ANSI B16.36a
NECK SCREWED
DIA. OF BOLT AT AT
NPS NO. OF DIA. OF BOLT DIA. RAISED RING BASE CHAMFER RAISED RING RAISED RING
4 8 1 7.88 7/8 5.5 6.0 5.75 4.50 83 92 65 74
100 8 26 200.0 7/8 140 153 146.1 114.3 37 41.5 29 33.5
5 ■ 8 1 9.25 7/8 5.75 6.25 7.0 5.56 99 110 75 85
■ 125 8 26 235.0 7/8 146 159 177.8 141.2 45 50 34 38
6 12 1 10.62 7/8 6.25 6.5 8.12 6.63 135 145 110 120
150 12 26 269.7 7/8 159 165 206.4 168.4 61 65 50 54
8 12 1.12 13.0 1 6.75 7.25 10.25 8.63 205 225 165 180
200 12 29 330.2 1 172 185 260.4 219.2 90 101 74 81
10 16 1.25 15.25 1 1/8 7.5 8.0 12.62 10.75 300 325 235 255
250 16 32 387.3 1 1/8 191 204 320.7 273.1 135 146 106 115
12 16 1.38 17.75 1 1/4 8.0 8.5 14.75 12.75 420 445 330 355
300 16 35 450.8 1 1/4 205 216 374.6 323.8 189 200 149 160

NECK THREADED
DIA. OF BOLT AT AT POINT
NPS NO. OF DIA. OF BOLT DIA. RAISED RING BASE OF WELDING RAISED RING RAISED RING
4 8 1.00 8.50 7/8 6.00 6.5 6.00 4.50 97 110 87 98
100 8 26 216 7/8 152 165 152 114 44 50 39 44
5 ■ 8 1.13 10.50 1 5.50 7.00 7.44 5.56 115 170 145 160
■ 125 8 29 267 1 140 178 189 141 52 77 66 72
6 12 1.13 11.50 1 7.00 7.5 8.75 6.63 195 210 190 205
150 12 29 292 1 178 191 222 168 89 95 86 92
8 12 1.25 13.75 1 1/8 7.75 8.25 10.75 8.63 285 305 275 295
200 12 32 349 1 1/8 197 210 273 219 129 138 125 133
10 16 1.38 17.00 1 1/4 8.75 9.25 13.50 10.75 450 485 410 445
250 16 35 432 1 1/4 222 235 343 273 204 220 186 200
12 20 1.38 19.25 1 1/4 9.00 9.5 15.75 12.75 540 580 490 530
300 20 35 489 1 1/4 229 241 400 324 245 263 222 239
The tapped metering holes are drilled as follows:

1/2" for sizes NPS 4 (DN 100) and over.
POUNDS
CLASS 900 (PN 150) For sizes 2 1/2 and smaller, use Class 1500 (PN 250)
BORE ∆
LENGTH THRU HUB
∆
3 9.50 1.50 1.50 5.00 3.57 4.00 4.00 2.12 2.12
80 241 38.5 38.5 127.0 90.7 101.6 101.6 54.0 54.0
4 11.50 1.75 1.75 6.19 4.57 4.50 4.50 2.75 2.75
100 292 44.5 44.5 157.2 As 116.1 114.3 114.3 70.0 70.0
5 ■ 13.75 2.00 2.00 7.31 5.66 5.00 5.00 3.12 3.12
■ 125 350 51.0 51.0 185.7 specified 143.8 127.0 127 79.4 79.4
6 15.00 2.19 2.19 8.50 6.72 5.50 5.50 3.38 3.38
150 381 56.0 56.0 215.9 by 170.7 139.7 139.7 85.7 85.7
8 18.50 2.50 2.50 10.63 8.72 6.38 6.38 4.00 4.00
200 470 63.5 63.5 270.0 221.5 161.9 161.9 101.6 101.6
purchaser
10 21.50 2.75 2.75 12.75 10.88 7.25 7.25 4.25 4.25
250 546 70.0 70.0 323.9 2 276.4 184.2 184.2 108.0 108.0
12 24.00 3.12 3.12 15.00 12.88 7.88 7.88 4.62 4.62
300 610 79.5 79.5 381.0 327.2 200.0 200.0 117.5 117.5
†
CLASS 1500 (PN 250)
BORE LENGTH THRU HUB
1 5.88 1.50 1.50 2.00 1.36 3.25 3.25 1.88 1.75
25 149 38.5 38.5 50.8 34.5 82.55 82.55 47.6 44.5
1 1/4 ■ 6.25 1.38 1.38 2.50 1.70 2.88 2.88 1.88 1.75
■ 32 159 34.9 34.9 63.5 43.2 73.15 73.15 47.6 44.5
1 1/2 7.00 1.50 1.50 2.88 1.95 3.50 3.50 1.88 1.75
40 178 38.5 38.5 73.0 49.5 88.90 88.90 47.6 44.5
2 8.50 1.50 1.50 3.62 2.44 4.00 4.00 2.25 2.25
50 216 38.5 38.5 92.1 62.0 101.6 101.6 57.2 57.2
2 1/2 9.62 1.62 1.62 4.12 As 2.94 4.12 4.12 2.50 2.50
65 245 41.5 41.5 104.8 74.7 104.8 104.8 63.5 63.5
3 10.50 1.88 1.88 5.00 specified 3.57 4.62 4.62 2.88 2.88
80 267 48.0 48.0 127.0 90.7 117.5 117.5 73.0 73.0
4 12.25 2.12 2.12 6.19 4.57 4.88 4.88 3.56 3.56
by
100 312 54.0 54.0 157.2 116.1 123.8 123.8 90.5 90.4
5 ■ 14.75 2.88 2.88 7.31 5.66 6.12 6.12 4.12 4.12
purchaser
■ 125 375 73.0 73.0 185.7 143.8 155.6 155.6 104.8 104.8
6 15.50 3.25 3.25 8.50 6.72 6.75 6.75 4.69 4.69
150 394 83.0 83.0 215.9 170.7 171.4 171.4 119.1 119.1
8 19.00 3.62 3.62 10.62 8.72 8.38 8.38 5.62 5.62
200 483 92.5 92.5 269.9 221.5 212.7 212.7 142.9 142.9
10 23.00 4.25 4.25 12.75 10.88 10.00 10.00 6.25 6.25
250 585 108.0 108.0 323.9 276.4 254.0 254.0 158.8 158.8
12 26.50 4.88 4.88 15.00 12.88 11.12 11.12 7.12 7.12
300 675 124.0 124.0 381.0 327.2 282.6 282.6 181.0 181.0
# Sizes NPS 14 (DN 350) and larger, on application. * Details of Ring Joint facings are given on page 30.
† Class 2500 (PN 400) Welding Neck Orifice Flanges, NPS 1 through 12 (DN FOR FURTHER DETAILS, REFER TO PAGE 4 “OTHER TYPES”.
25 through 300), as covered by ASME/ANSI B16.36 are available upon ∆ 0.25" (6.4 mm) Raised Face is not included in Flange Thickness T, and
application. • 28 • Length through Hub F & G.
■ Not covered by ASME/ANSI B16.36.
CLASS 900 (PN 150)
CLASS 1500 (PN 250)
FORGED
†
ORIFICE FLANGES
ASTM A-105
ASME/ANSI B16.36
OF HUB WELDING SLIP-ON AND
NECK THREADED
3 8 1.00 7.50 7/8 6.0 6.5 5.00 3.50 75 84 65 74
80 8 26 191 7/8 153 165 127 89.0 34 38 30 33
4 8 1.25 9.25 1 1/8 7.00 7.5 6.25 4.50 125 140 130 145
100 8 32 235 1 1/8 178 191 159 114.0 57 64 59 65
5 ■ 8 1.38 11.00 1 1/4 7.50 8.00 7.50 5.56 205 225 200 215
■ 125 8 36 279 1 1/4 191 204 191 141.3 93 102 91 97
6 12 1.25 12.50 1 1/8 7.75 8.25 9.25 6.63 260 290 260 285
150 12 32 318 1 1/8 197 210 235 168.0 118 132 118 128
8 12 1.50 15.50 1 3/8 9.00 9.5 11.75 8.63 420 450 410 435
200 12 39 394 1 3/8 229 241 298 219.0 191 204 186 196
10 16 1.50 18.50 1 3/8 9.5 10.0 14.50 10.75 610 660 580 620
250 16 39 470 1 3/8 241 254 368 273.0 277 299 263 279
12 20 1.50 21.00 1 3/8 10.25 10.75 16.50 12.75 760 820 760 820
300 20 39 533 1 3/8 260 273 419 324.0 345 372 345 360

NECK THREADED
1 4 1.00 4.00 7/8 6.00 6.25 2.06 1.32 29 28 26 26
25 4 26 102 7/8 153 159 52 33.5 13 13 12 12
1 1/4 ■ 4 1.00 4.38 7/8 5.50 5.75 2.50 1.66 31 31 29 29
■ 32 4 26 111 7/8 140 147 64 42.2 14 14 13 13
1 1/2 4 1.12 4.88 1 6.25 6.50 2.75 1.90 38 40 36 38
40 4 29 124 1 159 166 70 48.5 17 18 16 17
2 8 1.00 6.50 7/8 6.00 6.50 4.12 2.38 63 72 63 71
50 8 26 165 7/8 153 166 105 60.5 29 33 29 32
2 1/2 8 1.12 7.50 1 6.50 7.00 4.88 2.88 90 100 90 100
65 8 29 191 1 165 178 124 73.0 41 45 41 45
3 8 1.25 8.00 1 1/8 7.25 7.75 5.25 3.50 120 135 120 135
80 8 32 203 1 1/8 185 197 133 89.0 54 61 54 61
4 8 1.38 9.50 1 1/4 8.00 8.50 6.38 4.50 180 195 180 195
100 8 35 241 1 1/4 204 216 162 114.0 82 88 82 88
5 ■ 8 1.62 11.50 1 1/2 9.75 10.25 7.75 5.56 320 345 320 340
■ 125 8 42 292 1 1/2 248 261 197 141.0 145 157 145 153
6 12 1.50 12.50 1 3/8 10.50 11.00 9.00 6.63 405 440 405 435
150 12 39 318 1 3/8 267 280 229 168.0 184 200 184 196
8 12 1.75 15.50 1 5/8 11.75 12.50 11.50 8.63 630 730 600 680
200 12 45 394 1 5/8 299 318 292 219.0 286 331 272 305
10 12 2.00 19.00 1 7/8 13.50 14.25 14.50 10.75 1100 1175 1050 1125
250 12 51 483 1 7/8 343 362 368 273.0 499 533 476 506
12 16 2.12 22.50 2 15.00 16.00 17.75 12.75 1675 1825 1475 1550
300 16 54 572 2 381 407 451 324.0 760 828 664 698
FOR FURTHER DETAILS, REFER TO PAGE 4 “OTHER TYPES”. The tapped metering holes are drilled as follows:
1/2" for sizes NPS 4 (DN 100) and over.
INCHES POUNDS 3/8" for sizes NPS 3 (DN 80).
1/4" for sizes NPS 2 1/2 (DN 65) and under.
MILLIMETRES KILOGRAMS • 29 •
RING ENLARGED
SECTION OF
JOINT GROOVE
DIMENSIONS
ASME/ANSI B16.5
NOMINAL PIPE SIZE GROOVE DIMENSIONS DIAMETER OF RAISED FACE K
PITCH BOTT.
DIA. DEPTH WIDTH RADIUS 300
CLASS 150 300 2
400 600 3
900 1500 2500 RING 150 400,600 900 1500 2500
PN 20 50 64 100 160 250 400 NUMBER P E4 F R 20 50,64,100 160 250 400
NPS 1/2 1/2 R11 1.344 0.219 0.281 .03 2
DN 15 15 R11 34.14 5.56 7.14 .8 51.0
NPS 1/2 R12 1.562 0.250 0.344 .03 2.38
DN 15 R12 39.67 6.35 8.74 .8 60.5
NPS 3/4 3/4 1/2 R13 1.688 0.250 0.344 .03 2.5 2.56
DN 20 20 15 R13 42.88 6.35 8.74 .8 63.5 65.0
NPS 3/4 R14 1.750 0.250 0.344 .03 2.62
DN 20 R14 44.45 6.35 8.74 .8 66.5
NPS 1 R15 1.875 0.250 0.344 .03 2.50
DN 25 R15 47.62 6.35 8.74 .8 63.5
NPS 1 1 1 3/4 R16 2.000 0.250 0.344 .03 2.75 2.81 2.88
DN 25 25 25 20 R16 50.80 6.35 8.74 .8 70.0 71.5 73.0
NPS 1 1/4 R17 2.250 0.250 0.344 .03 2.88
DN 32 R17 57.15 6.35 8.74 .8 73.0
NPS 1 1/4 1 1/4 1 1/4 1 R18 2.375 0.250 0.344 .03 3.12 3.19 3.25
DN 32 32 32 25 R18 60.32 6.35 8.74 .8 79.5 81.0 82.5
NPS 1 1/2 R19 2.562 0.250 0.344 .03 3.25
DN 40 R19 65.07 6.35 8.74 .8 82.5
NPS 1 1/2 1/2 1 1/2 R20 2.688 0.250 0.344 .03 3.56 3.62
DN 40 40 40 R20 68.28 6.35 8.74 .8 90.5 92.0
NPS 1 1/4 R21 2.844 0.312 0.469 .03 4
DN 32 R21 72.24 7.92 11.91 .8 102
NPS 2 R22 3.250 0.250 0.344 .03 4
DN 50 R22 82.55 6.35 8.74 .8 102
NPS 2 2 1 1/2 R23 3.250 0.312 0.469 .03 4.25 4.5
DN 50 50 40 R23 82.55 7.92 11.91 .8 108 114
NPS 2 R24 3.750 0.312 0.469 .03 4.88
DN 50 R24 95.25 7.92 11.91 .8 124
NPS 2 1/2 R25 4.000 0.250 0.344 .03 4.75
DN 65 R25 101.60 6.35 8.74 .8 121
NPS 2 1/2 2 1/2 2 R26 4.000 0.312 0.469 .03 5 5.25
DN 65 65 50 R26 101.60 7.92 11.91 .8 127 133
NPS 2 1/2 R27 4.250 0.312 0.469 .03 5.38
DN 65 R27 107.95 7.92 11.91 .8 137
NPS 2 1/2 R28 4.375 0.375 0.531 .06 5.88
DN 65 R28 111.12 9.52 13.49 1.5 149
NPS 3 R29 4.500 0.250 0.344 .03 5.25
DN 80 R29 114.30 6.35 8.74 .8 133
NPS (1) (1) R30 4.625 0.312 0.469 .03
DN (1) (1) R30 117.48 7.92 11.91 .8
NPS 3 (1) 3 (1) 3 R31 4.875 0.312 0.469 .03 5.75 6.12
DN 80 80 80 R31 123.82 7.92 11.91 .8 146 156
NPS 3 R32 5.000 0.375 0.531 .06 6.62
DN 80 R32 127.00 9.52 13.49 1.5 168
1
For NPS 3 (DN 80) Lap Joint Stub Ends (ASME/ASNI B16.9) Class 300 & TOLERANCES
600 (PN 50 & 100), Ring Number R30 is used instead of R31. E (depth) + 0.16 (+ 0.40 mm) - 0.00 (-0.00 mm)
2
For sizes NPS 1/2 - NPS 3 1/2 (DN 15 - DN 90), use same data as Class F (width) ± 0.008 (±0.20 mm)
600 (PN 100). P (pitch) ± 0.005 (± 0.13 mm)
3
For sizes NPS 1/2 - NPS 2 1/2 (DN 15 - DN 65) use same data as Class R (radius) Max.
1500 (PN 250). 23˚ (angle) ± 1/2˚
4
Height of raised portion is equal to the depth of groove dimensions “E” but is
not subjected to the tolerance for “E”. Former full-face contour may be used. INCHES
RING JOINT DIMENSIONS continued
PITCH BOTT.
DIA. DEPTH WIDTH RADIUS 300
CLASS 150 300 400
2
600 3
900 1500 2500 RING 150 400,600 900 1500 2500
PN 20 50 64 100 160 250 400 NUMBER P E4 F R 20 50,64,100 160 250 400
NPS 3 1/2 R33 5.188 0.250 0.344 .03 6.06
DN 90 R33 131.78 6.35 8.74 .8 154
NPS 3 1/2 3 1/2 R34 5.188 0.312 0.469 .03 6.25
DN 90 90 R34 131.78 7.92 11.91 .8 159
NPS 3 R35 5.375 0.312 0.469 .03 6.62
DN 80 R35 136.52 7.92 11.91 .8 168
NPS 4 R36 5.875 0.250 0.344 .03 6.75
DN 100 R36 149.22 6.35 8.74 .8 171
NPS 4 4 4 4 R37 5.875 0.312 0.469 .03 6.88 7.12
DN 100 100 100 100 R37 149.22 7.92 11.91 .8 175 181
NPS 4 R38 6.188 0.438 0.656 .06 8
DN 100 R38 157.18 11.13 16.66 1.5 203
NPS 4 R39 6.375 0.312 0.469 .03 7.62
DN 100 R39 161.92 7.92 11.91 .8 194
NPS 5 R40 6.750 0.250 0.344 .03 7.62
DN 125 R40 171.45 6.35 8.74 .8 194
NPS 5 5 5 5 R41 7.125 0.312 0.469 .03 8.25 8.5
DN 125 125 125 125 R41 180.98 7.92 11.91 .8 210 216
NPS 5 R42 7.500 0.500 0.781 .06 9.5
DN 125 R42 190.50 12.70 19.84 1.5 241
NPS 6 R43 7.625 0.250 0.344 .03 8.62
DN 150 R43 193.68 6.35 8.74 .8 219
NPS 5 R44 7.625 0.312 0.469 .03 9
DN 125 R44 193.68 7.92 11.91 .8 229
NPS 6 6 6 6 R45 8.312 0.312 0.469 .03 9.5 9.5
DN 150 150 150 150 R45 211.12 7.92 11.91 .8 241 241
NPS 6 R46 8.312 0.375 0.531 .06 9.75
DN 150 R46 211.12 9.52 13.49 1.5 248
NPS 6 R47 9.000 0.500 0.781 .06 11
DN 150 R47 228.60 12.70 19.84 1.5 279
NPS 8 R48 9.750 0.250 0.344 .03 10.75
DN 200 R48 247.65 6.35 8.74 .8 273
NPS 8 8 8 8 R49 10.625 0.312 0.469 .03 11.88 12.12
DN 200 200 200 200 R49 269.88 7.92 11.91 .8 302 308
NPS 8 R50 10.625 0.438 0.656 .06 12.5
DN 200 R50 269.88 11.13 16.66 1.5 318
NPS 8 R51 11.000 0.562 0.906 .06 13.38
DN 200 R51 279.40 14.27 23.01 1.5 340
NPS 10 R52 12.000 0.250 0.344 .03 13
DN 250 R52 304.80 6.35 8.74 .8 330
NPS 10 10 10 10 R53 12.750 0.312 0.469 .03 14 14.25
DN 250 250 250 250 R53 323.85 7.92 11.91 .8 356 362
NPS 10 R54 12.750 0.438 0.656 .06 14.62
DN 250 R54 323.85 11.13 16.66 1.5 371
NPS 10 R55 13.500 0.688 1.188 .09 16.75
DN 250 R55 342.90 17.48 30.18 2.4 425
FOR FOOTNOTES, REFER TO PAGE 30 CONTINUED ON PAGE 32
INCHES
RING JOINT ENLARGED
SECTION OF
DIMENSIONS GROOVE
continued
PITCH BOTT.
DIA. DEPTH WIDTH RADIUS 300,
CLASS 150 300 400
2
600 3
900 1500 2500 RING 150 400,600 900 1500 2500
PN 20 50 64 100 160 250 400 NUMBER P E
4
F R 20 50,64,100 160 250 400
NPS 12 R56 15.000 0.250 0.344 .03 16
DN 300 R56 381.00 6.35 8.74 .8 406
NPS 12 12 12 12 R57 15.000 0.312 0.469 .03 16.25 16.5
DN 300 300 300 300 R57 381.00 7.92 11.91 .8 413 419
NPS 12 R58 15.000 0.562 0.906 .06 17.25
DN 300 R58 381.00 14.27 23.01 1.5 438
NPS 14 R59 15.625 0.250 0.344 .03 16.75
DN 350 R59 396.88 6.35 8.74 .8 425
NPS 12 R60 16.000 0.688 1.312 .09 19.5
DN 300 R60 406.40 17.48 33.32 2.4 495
NPS 14 14 14 R61 16.500 0.312 0.469 .03 18
DN 350 350 350 R61 419.10 7.92 11.91 .8 457
NPS 14 R62 16.500 0.438 0.656 .06 18.38
DN 350 R62 419.10 11.13 16.66 1.5 467
NPS 14 R63 16.500 0.625 1.062 .09 19.25
DN 350 R63 419.10 15.88 26.97 2.4 489
NPS 16 R64 17.875 0.250 0.344 .03 19
DN 400 R64 454.02 6.35 8.74 .8 483
NPS 16 16 16 R65 18.500 0.312 0.469 .03 20
DN 400 400 400 R65 469.90 7.92 11.91 .8 508
NPS 16 R66 18.500 0.438 0.656 .06 20.62
DN 400 R66 469.90 11.13 16.66 1.5 524
NPS 16 R67 18.500 0.688 1.188 .09 21.5
DN 400 R67 469.90 17.48 30.18 2.4 546
NPS 18 R68 20.375 0.250 0.344 .03 21.5
DN 450 R68 517.52 6.35 8.74 8 546
NPS 18 18 18 R69 21.000 0.312 0.469 .03 22.62
DN 450 450 450 R69 533.40 7.92 11.91 8 575
NPS 18 R70 21.000 0.500 0.781 .06 23.38
DN 450 R70 533.40 12.70 19.84 1.5 594
NPS 18 R71 21.000 0.688 1.188 .09 24.12
DN 450 R71 533.40 17.48 30.18 2.4 613
NPS 20 R72 22.000 0.250 0.344 .03 23.5
DN 500 R72 558.80 6.35 8.74 .8 597
NPS 20 20 20 R73 23.000 0.375 0.531 .06 25
DN 500 500 500 R73 584.20 9.52 13.49 1.5 635
NPS 20 R74 23.000 0.500 0.781 .06 25.5
DN 500 R74 584.20 12.70 19.84 1.5 648
NPS 20 R75 23.000 0.688 1.312 .09 26.5
DN 500 R75 584.20 17.48 33.32 2.4 673
NPS 24 R76 26.500 0.250 0.344 .03 28
DN 600 R76 673.10 6.35 8.74 .8 711
NPS 24 24 24 R77 27.250 0.438 0.656 .06 29.5
DN 600 600 600 R77 692.15 11.13 16.66 1.5 749
NPS 24 R78 27.250 0.625 1.062 .09 30.38
DN 600 R78 692.15 15.88 26.97 2.4 772
NPS 24 R79 27.250 0.812 1.438 .09 31.25
DN 600 R79 692.15 20.62 36.53 2.4 794
FOR FOOTNOTES, REFER TO PAGE 30
INCHES
LONG
WELDING
NECKS
LENGTH THRU HUB WEIGHTS

NOMINAL CLASS 150 CLASS 900 HUB
SIZE THRU 600 THRU 2500 DIAMETER CLASS CLASS CLASS CLASS CLASS CLASS CLASS
AND PN PN CLASS 150 150 300 400 600 900 1500 2500
BORE 20 THRU 100 160 THRU 400 PN 20 PN 20 PN 50 PN 64 PN 100 PN 160 PN 250 PN 400
B F F *M
1.00 9 9 2.00 8 10 11 11 15 15 20
25.4 229 229 50.8 3.6 4.5 5 5 7 7 9
1.25 9 9 2.38 10 14 14 14 18 18 30
31.8 229 229 60.3 4.5 6.5 6.5 6.5 8 8 13.5
1.50 9 9 2.62 12 17 17 17 23 23 38
38.1 229 229 66.7 5.5 7.7 7.7 7.7 10.5 10.5 17
2.00 9 9 3.25 17 19 21 21 44 44 55
50.8 229 229 82.6 7.7 9 9.5 9.5 20 20 25
2.50 9 12 3.75 22 28 29 29 72 72 85
63.5 229 305 95.3 10 13 13 13 32.5 32.5 38.5
3.00 9 12 4.25 26 36 38 38 65 84 125
76.2 229 305 108.0 12 16.5 17.5 17.5 29.5 38 57
3.50 9 - 4.88 32 45 48 48 - - -
88.9 229 - 123.8 14.5 20.5 21.5 22 - - -
4.00 12 12 5.50 47 54 67 80 98 118 185
101.6 305 305 139.7 21.5 24.5 30 36.5 44 53 84
5.00 12 12 6.50 58 86 90 128 143 195 300
127.0 305 305 165.1 26.5 39 41 58 65 88 135
6.00 12 12 7.75 77 108 115 158 199 235 450
152.4 305 305 196.9 35 49 52 72 90 106 203
8.00 12 12 9.75 103 150 160 215 310 366 600
203.2 305 305 247.7 47 68 72 98 140 165 270
10.00 12 12 12.00 144 218 230 343 356 594 1045
254.0 305 305 304.8 66 99 104 156 161 268 471
12.00 12 12 14.38 207 289 301 409 541 872 1420
304.8 305 305 365.1 94 131 136 186 244 393 639
14.00 12 12 16.00 212 342 357 432 568 1030 -
355.6 305 305 406.4 96 155 161 196 256 464 -
16.00 12 12 18.00 250 426 443 564 670 1335 -
406.4 305 305 457.2 114 193 199 256 302 601 -
18.00 12 12 20.00 274 493 513 654 949 1750 -
457.2 305 305 508.0 125 224 231 297 427 788 -
20.00 12 12 22.00 314 575 602 840 1040 2130 -
508.0 305 305 558.8 143 261 271 381 468 959 -
24.00 12 12 26.25 426 823 856 1100 1775 3180 -
609.6 305 305 666.8 194 374 385 499 799 1431 -
SPECIFICATIONS: Long Welding Necks conform to ASTM *Dimension “M” is given here for Class 150 (PN 20) Long Welding
specification A-105. Except as shown above, Long Welding Necks Necks only. For Class 300 (PN 50) and higher pressure ratings,
conform dimensionally to ASME/ANSI Standard B16.5. outside diameter of the neck is the same as dimension “M” of ANSI
flanges of comparable pressure rating (see pages 8 to 18).
Facing and Finish: see page 4.
Gasket dimensions: see page 20.
Bolting dimensions: see page 22.
INCHES POUNDS
LARGE DIAMETER
CLASS 125 LW1
SLIP-ON FLANGES2
3
ASTM A181 CLASS 60
DRILLING
FLANGE LENGTH DIAMETER NO. DIAMETER DIA. OF

OUTSIDE FLANGE BORE
4
THRU OF HUB OF OF BOLT BOLT APPROX.
NPS DIAMETER THICKNESS DIAMETER HUB AT BASE HOLES HOLES DIAMETER CIRCLE WEIGHT
DN O T C G M J K
26 34.25 1.00 1.75 28.50 24 1.38 1 1/4 31.75 123
650 870 25.4 44.5 723.9 24 35 1 1/4 806.5 56
28 36.5 1.00 1.75 30.50 28 1.38 1 1/4 34.00 141
700 927 25.4 44.5 774.7 28 35 1 1/4 863.6 64
30 38.75 1.00 1.75 32.50 28 1.38 1 1/4 36.00 151
750 985 25.4 44.5 825.5 28 35 1 1/4 914.4 68.5
32 41.75 1.12 1.75 34.75 28 1.62 1 1/2 38.50 207
800 1061 28.6 44.5 882.7 28 41 1 1/2 977.9 94
34 43.75 1.12 1.75 36.75 32 1.62 1 1/2 40.50 218
1111 28.6 44.5 933.5 32 41 1 1/2 1028.7 99
36 46 1.12 1.75 38.75 32 1.62 1 1/2 42.75 233
900 1169 28.6 44.5 984.3 32 41 1 1/2 1085.9 106
38 48.75 1.12 1.75 40.75 32 1.62 1 1/2 45.25 261
1238 28.6 44.5 1035.1 32 41 1 1/2 1149.4 118
40 50.75 1.12 1.75 43.00 36 1.62 1 1/2 47.25 283
1000 1289 28.6 44.5 1092 36 41 1 1/2 1200.2 128
42 53 1.25 As 1.75 45.00 36 1.62 1 1/2 49.50 332
1100 1346 31.8 44.5 1143 36 41 1 1/2 1257.3 151
44 55.25 1.25 specified 2.25 47.00 40 1.62 1 1/2 51.75 353
1404 31.8 57.2 1194 40 41 1 1/2 1314.5 160
46 57.25 1.25 by 2.25 49.00 40 1.62 1 1/2 53.75 364
1454 3.8 57.2 1245 40 41 1 1/2 1365.3 165
48 59.5 1.38 purchaser 2.50 51.00 44 1.62 1 1/2 56.00 425
1200 1511 34.9 63.5 1295 44 41 1 1/2 1422.4 193
50 61.75 1.38 2.50 53.00 44 1.88 1 3/4 58.25 455
1569 34.9 63.5 1346 44 48 1 3/4 1479.6 206
52 64 1.38 2.50 55.00 44 1.88 1 3/4 60.50 470
1300 1626 34.9 63.5 1397 44 48 1 3/4 1536.7 213
54 66.25 1.38 2.50 57.00 44 1.88 1 3/4 62.75 510
1400 1683 34.9 63.5 1448 44 48 1 3/4 1593.9 231
60 73 1.50 2.75 63.00 52 1.88 1 3/4 69.25 645
1500 1854 38.1 69.9 1600 52 48 1 3/4 1759.0 293
66 80 1.50 2.75 69.00 52 1.88 1 3/4 76.00 760
2032 38.1 69.9 1753 52 48 1 3/4 1930.4 345
72 86.5 1.50 2.75 75.00 60 1.88 1 3/4 82.50 845
1800 2197 38.1 69.9 1905 60 48 1 3/4 2095.5 383
84 99.75 1.75 3.00 87.50 64 2.12 2 95.50 1015
2534 44.5 76.2 2223 64 54 2 2425.7 460
96 113.25 2.00 3.25 100.00 68 2.38 2 1/4 108.50 1660
2400 2877 50.8 82.6 2540 68 61 2 1/4 2755.9 753
1
Class 125LW Slip-on Flanges in pipe sizes NPS 6 to 96 (DN 150 to 2400) are identical with NOTE: At the time of printing this catalogue the metric
AWWA Class D Flanges, as shown on page 40, and have the same diameter and drilling as Class Pressure Number (PN) equivalent of the Class 125
125 Cast Iron Flanges, ANSI B16.1 pressure rating of these LW flanges had not been
These flanges are designed for use with full face gaskets, but ring gaskets extending to the inside
established, neither had the metric Nominal Diameter (DN)
edge of the bolt holes may also be used.
2
Blind Flanges are available on request.
conversions for various NPS sizes.
3
Can also be furnished in A181 Class 70 and A105 or any other material that can be forged or
rolled. INCHES POUNDS
4
When specifying bore it is recommended that this dimension be .19" (4.88 mm)
• 34 • MILLIMETRES KILOGRAMS
larger than the nominal O.D. of the pipe.
LARGE DIAMETER
CLASS 125 1
AMERICAN STANDARD
WELDING NECK &
2
SLIP-ON FLANGES
3
ASTM A181 CLASS 60
LENGTH THRU DIAMETER APPROXIMATE
BORE DRILLING
HUB OF HUB WEIGHT
DIA.
FLANGE OF AT POINT NO. DIA. DIA. OF
OUTSIDE FLANGE 5RAISED WELDING WELDING AT OF OF OF BOLT WELDING
NPS DIA. THICKNESS FACE NECK SLIP-ON NECK SLIP-ON BASE WELDING HOLES HOLES CIRCLE NECK SLIP-ON
DN O T R B C F G M N J K
26 34.25 2.00 29.25 26.25 5.00 3.38 28.50 26 24 1.38 31.75 262 233
650 870 50.8 743 666.8 127.0 85.7 723.9 660 24 35 806.5 118 105
28 36.5 2.06 31.25 28.25 5.06 3.44 30.75 28 28 1.38 34.00 291 275
700 927 52.4 794 717.6 128.6 87.3 781.1 711 28 35 863.6 131 124
30 38.75 2.12 33.75 30.25 5.12 3.5 32.75 30 28 1.38 36.00 341 300
750 985 54.0 857 768.4 130.2 88.9 831.9 762 28 35 914.4 154 135
32 41.75 2.25 35.75 32.25 5.25 3.62 35.00 32 28 1.62 38.50 412 370
800 1061 57.2 908 819.2 133.4 92.1 889.0 813 28 41 977.9 186 167
34 43.75 2.31 37.75 34.25 5.31 3.69 37 34 32 1.62 40.50 439 410
- 1111 58.7 959 870.0 134.9 93.7 939.8 864 32 41 1028.7 198 185
36 46 2.38 40.25 36.25 5.38 3.75 39.25 36 32 1.62 42.75 495 460
900 1169 60.3 1022 920.8 136.5 95.3 997.0 914 32 41 1085.9 223 207
38 48.75 2.38 42.25 38.25 5.38 3.75 41.75 38 32 1.62 45.25 573 525
- 1238 60.3 1073 971.6 136.5 95.3 1060.5 965 32 41 1149.4 258 236
40 50.75 2.50 44.25 40.25 5.50 3.88 43.75 40 36 1.62 47.25 619 575
1000 1289 63.5 1124 1022.4 139.7 98.4 1111.3 1016 36 41 1200.2 279 259
42 53 2.62 47 As
42.25
4 5.62 4.00 46.00 42 36 1.62 49.50 715 660
1100 1346 66.7 1194 1073.2 142.9 101.6 1168.4 1067 36 41 1257.3 322 297
44 55.25 2.62 49 specified
44.25 5.62 4.00 48.00 44 40 1.62 51.75 755 695
- 1404 66.7 1245 1124.0 142.9 101.6 1219.2 1118 40 41 1314.5 340 313
46 57.25 2.69 51 by 46.25 5.69 4.06 50.00 46 40 1.62 53.75 805 730
- 1454 68.3 1295 1174.8 144.5 103.2 1270.0 1168 40 41 1365.3 362 329
48 59.5 2.75 53.5 purchaser 48.25 5.75 4.12 52.25 48 44 1.62 56.00 880 810
1200 1511 69.9 1359 1225.6 146.1 104.8 1327.2 1219 44 41 1422.4 396 365
50 61.75 2.75 55.5 50.25 5.75 4.12 54.25 50 44 1.88 58.25 915 840
- 1569 69.9 1410 1276.4 146.1 104.8 1378.0 1270 44 48 1479.6 412 378
52 64.0 2.88 57.5 52.25 5.88 4.25 56.50 52 44 1.88 60.50 1020 925
1300 1626 73.0 1461 1327.2 149.2 108.0 1435.1 1321 44 48 1536.7 459 416
54 66.25 3.00 59.75 54.25 6.00 4.38 58.75 54 44 1.88 62.75 1110 1040
1400 1683 76.2 1518 1378.0 152.4 111.1 1492.3 1372 44 48 1593.9 500 468
60 73.0 3.12 66 60.25 6.12 4.50 65.25 60 52 1.88 69.25 1360 1275
1500 1854 79.4 1676 1530.4 155.6 114.3 1657.4 1524 52 48 1759.0 612 574
66 80.0 3.38 73 66.25 6.38 4.88 71.50 66 52 1.88 76.00 1770 1625
- 2032 85.7 1855 1682.8 161.9 123.8 1816.1 1676 52 48 1930.4 797 731
72 86.5 3.50 79.5 72.25 6.50 5.00 78.50 72 60 1.88 82.50 2125 1950
1800 2197 88.9 2019 1835.2 165.1 127.0 1993.9 1829 60 48 2095.5 956 878
84 99.75 3.88 92.5 84.25 6.88 5.38 90.50 84 64 2.12 95.50 2825 2620
- 2534 98.4 2350 2140.0 174.6 136.5 2298.7 2134 64 54 2425.7 1271 1179
96 113.25 4.25 105.5 96.25 7.25 5.75 102.75 96 68 2.38 108.50 3830 3295
2400 2877 108.0 2680 2444.8 184.2 146.1 2609.9 2438 68 61 2755.9 1724 1483
1 4
These flanges have the same pressure ratings, dimensions and drillings as Class 125 Cast When ordering Welding Necks, specify thickness and O.D. of pipe or vessel
Iron Flanges, ASME/ANSI B16.1. Class 125 American Standard slip-on flanges are also the to which the flange is to be welded.
5
same as AWWA Class E flanges. All sizes are regularly furnished with flat face. A .06" (1.6 mm) raised face
2
Blind Flanges are available on request. can be furnished on request.
3
Can also be furnished in A181 Class 70 and A105 or any other material that can be forged
or rolled. NOTE: At the time of printing this catalogue the metric Pressure Number
(PN) equivalent of the Class 125 pressure rating of these flanges had not
INCHES POUNDS been established, neither had the metric Nominal Diameter (DN) conversions
for various NPS sizes.
LARGE DIAMETER FORGED STEEL FLANGES
1
CLASS 250
AMERICAN STANDARD
WELDING NECK &
2
SLIP-ON FLANGES
3
ASTM A181-CLASS 60
DIA. OF DRILLING
FLANGE LENGTH DIA. HUB AT DIA. OF DIAMETER DIA. OF
OUTSIDE FLANGE THRU OF HUB POINT OF RAISED NO. OF OF DIA. OF BOLT APPROX.
NPS DIAMETER THICKNESS BORE HUB AT BASE WELDING FACE HOLES HOLES BOLTS CIRCLE WEIGHT
DN O T B G M N A J K
WELDING NECK
26 38.25 2.81 5.81 30.50 26 32.44 28 1.88 1 3/4 34.50 535
650 972 71.4 147.6 774.7 660 823.9 28 48 1 3/4 876.3 241
28 40.75 2.94 5.94 33.00 28 34.94 28 1.88 1 3/4 37.00 640
700 10.35 74.6 150.9 838.2 711 887.5 28 48 1 3/4 939.8 289
30 43.0 3.00 6.00 35.25 30 37.19 28 1.88 1 3/4 39.25 695
750 1092 76.2 152.4 895.4 762 944.6 28 48 1 3/4 997.0 313
32 45.25 3.12 6.12 37.50 32 39.44 28 1.88 1 3/4 41.50 780
800 1150 79.4 155.6 952.5 813 1001.8 28 48 1 3/4 1054.1 351
34 47.5 3.25 6.25 39.50 34 41.44 28 1.88 1 3/4 43.50 885
As
1207 82.6 158.8 1003.3 864 1052.5 28 48 1 3/4 1104.9 398
36 50 3.38 6.38 41.50 36 43.69 32 2.12 2 46.00 965
specified
900 1270 85.7 161.9 1054.1 914 1109.7 32 54 2 1168.4 434
38 52.25 3.44 6.44 43.50 38 45.69 32 2.12 2 48.00 1040
by
1327 87.3 163.5 1104.9 965 1160.5 32 54 2 1219.2 468
40 54.5 3.56 6.56 45.75 40 47.94 36 2.12 2 50.25 1150
purchaser
1000 1384 90.5 166.7 1162.1 1016 1217.6 36 54 2 1276.4 518
42 57 3.69 6.94 47.75 42 50.44 36 2.12 2 52.75 1340
1100 1448 93.7 176.2 1212.9 1067 1281.1 36 54 2 1339.9 603
44 59.25 3.75 7.00 49.75 44 52.69 36 2.12 2 55.00 1420
1505 95.3 177.8 1263.7 1118 1338.3 36 54 2 1397.0 639
46 61.5 3.88 7.12 51.75 46 54.94 40 2.12 2 57.25 1525
1562 98.4 181.0 1314.5 1169 1395.4 40 54 2 1545.2 686
48 65 4.00 7.25 54.00 48 58.44 40 2.12 2 60.75 1850
1200 1651 101.6 184.2 1371.6 1219 1484.3 40 54 2 1543.1 833
SLIP-ON
26 38.25 2.81 26.25 4.75 30.50 - 32.44 28 1.88 1 3/4 34.50 530
650 972 71.4 666.8 120.7 774.7 - 823.9 28 48 1 3/4 876.3 239
28 40.75 2.94 28.25 5.00 33.00 - 34.94 28 1.88 1 3/4 37.00 630
700 1035 74.6 717.6 127.0 838.2 - 887.5 28 48 1 3/4 939.8 284
30 43 3.00 30.25 5.00 35.25 - 37.19 28 1.88 1 3/4 39.25 700
750 1093 76.2 768.4 127.0 895.4 - 944.6 28 48 1 3/4 997.0 315
32 45.25 3.12 32.25 5.12 37.50 - 39.44 28 1.88 1 3/4 41.50 800
800 1150 79.4 819.2 130.2 952.5 - 1001.8 28 48 1 3/4 1054.1 360
34 47.5 3.25 34.25 5.25 39.50 - 41.44 28 1.88 1 3/4 43.50 895
1207 82.6 870.0 133.4 1003.3 - 1052.5 28 48 1 3/4 1104.9 403
36 50 3.38 36.25 5.38 41.50 - 43.69 32 2.12 2 46.00 975
900 1270 85.7 920.8 136.5 1054.1 - 1109.7 32 54 2 1168.4 439
38 52.25 3.44 38.25 5.50 43.50 - 45.69 32 2.12 2 48.00 1070
1328 87.3 971.6 139.7 1104.9 - 1160.5 32 54 2 1219.2 482
40 54.5 3.56 40.25 5.50 45.75 - 47.94 36 2.12 2 50.25 1180
1000 1385 90.5 1022.4 139.7 1162.1 - 1217.6 36 54 2 1276.4 531
42 57 3.69 42.25 5.62 47.75 - 50.44 36 2.12 3 52.75 1310
1100 1448 93.7 1073.2 142.9 1212.9 - 1281.1 36 54 2 1339.9 590
44 59.25 3.75 44.25 5.75 49.75 - 52.69 36 2.12 2 55.00 1420
1505 95.3 1124.0 146.1 1263.7 - 1338.3 36 54 2 1397.0 639
46 61.5 3.88 46.25 5.88 51.75 - 54.94 40 2.12 2 57.25 1510
1562 98.4 1174.8 149.2 1314.5 - 1395.4 40 54 2 1454.2 680
48 65 4.00 48.25 6.00 54.00 - 58.44 40 2.12 2 60.75 1825
1200 1651 101.6 1225.6 152.4 1371.6 - 1484.3 40 54 2 1543.1 821
1
These flanges have the same pressure ratings, dimensions and NOTE: At the time of printing this catalogue the metric Pressure Number (PN) equivalent of the Class
drillings as Class 250 Cast Iron Flanges ASME/ANSI B16.1. 125 pressure rating of these LW flanges had not been established, neither had the metric Nominal
2
Blind Flanges are available upon application. Diameter (DN) conversions for
3 various NPS sizes. INCHES POUNDS
Can also be furnished in A181 Class 70, and A-105 or any
other material that can be forged or rolled. • 36 • MILLIMETRES KILOGRAMS
1
CLASS 75
PRESSURE VESSEL FLANGES
2
WELDING NECK & SLIP-ON
For Nominal I.D. Vessels
4
ASTM A181 - CLASS 60
DIA. OF DRILLING
NOMINAL FLANGE LENGTH DIA. HUB AT DIA. OF DIAMETER DIA. OF
SIZE OUTSIDE FLANGE THRU OF HUB POINT OF RAISED NO. OF OF DIA. OF BOLT APPROX.
(INSIDE DIAMETER THICKNESS BORE HUB AT BASE WELDING FACE HOLES HOLES BOLTS CIRCLE WEIGHT
DIAMETER) O C B3 Y X A3 R K
WELDING NECK
26 31.5 1.25 3.00 27.12 28.62 32 1 7/8 29.62 95
660 800 31.8 76.2 688.8 727.1 32 26 7/8 752.5 43
28 33.5 1.25 3.00 29.12 30.62 36 1 7/8 31.62 105
711 85 31.8 76.2 739.8 777.9 36 26 7/8 803.3 47
30 35.5 1.25 3.00 31.12 32.62 36 1 7/8 33.62 112
762 902 31.8 76.2 790.6 828.7 36 26 7/8 854.1 51
32 38.25 1.25 3.25 33.38 35.00 36 1.12 1 36.12 141
813 972 31.8 82.6 847.7 889.0 36 29 1 917.6 64
34 40.25 1.25 3.25 35.38 37.00 40 1.12 1 38.12 153
As As
864 1023 31.8 82.6 898.5 939.8 40 29 1 968.4 69
36 42.25 1.25 3.25 37.38 39.00 40 1.12 1 40.12 165
specified specified
914 1073 31.8 82.6 949.3 990.6 40 29 1 1019.2 74
42 49 1.25 3.50 43.75 45.50 48 1.25 1 1/8 46.75 205
by by
1067 1245 31.8 88.9 1111.3 1155.7 48 32 1 1/8 1187.5 92
48 55 1.25 3.75 49.75 51.50 52 1.25 1 1/8 52.75 245
purchaser purchaser
1219 1397 31.8 95.3 1263.7 1308.1 52 32 1 1/8 1339.9 110
54 61.25 1.38 4.00 56.00 57.75 64 1.25 1 1/8 59.00 305
1372 1556 35.1 101.6 1422.4 1466.9 64 32 1 1/8 1498.6 137
60 67.25 1.62 4.38 62.00 63.75 72 1.25 1 1/8 65.00 410
1524 1708 41.3 111.1 1574.8 1619.3 72 32 1 1/8 1651.0 185
66 74 1.88 4.88 68.0 70.12 72 1.38 1 1/4 71.50 575
1676 1880 47.6 123.8 1727.2 1781.2 72 35 1 1/4 1816.1 259
72 80 2.25 5.25 74.00 76.12 80 1.38 1 1/4 77.50 720
1829 2032 57.2 133.4 1879.6 1933.6 80 35 1 1/4 1968.5 324
SLIP-0N
26 33 1.25 2.25 28.50 - 30.00 32 1 7/8 31.00 115
660 838 31.8 57.2 723.9 - 762.0 32 26 7/8 787.4 52
28 35 1.25 2.25 30.50 - 32.00 36 1 7/8 33.00 140
711 889 31.8 57.2 774.7 - 812.8 36 26 7/8 838.2 63
30 37 1.25 2.25 32.50 - 34.00 36 1 7/8 35.00 155
762 940 31.8 57.2 825.5 - 863.6 36 26 7/8 889.0 70
32 39.5 1.25 2.50 34.62 - 36.25 40 1.12 1 37.38 165
813 1004 31.8 63.5 879.5 - 920.8 40 29 1 949.3 74
34 41.5 1.25 2.50 36.62 - 38.25 40 1.12 1 39.38 175
As
864 1054 31.8 63.5 930.3 - 971.6 40 29 1 1000.1 79
36 43.5 1.25 2.50 38.62 - 40.25 44 1.12 1 41.38 190
specified
914 1105 31.8 63.5 981.1 - 1022.4 44 29 1 1050.9 86
42 50 1.25 2.75 44.75 - 46.50 48 1.25 1 1/8 47.75 225
by
1067 1270 31.8 69.9 1136.6 - 1181.1 48 32 1 1/8 1212.9 101
48 56 1.25 2.88 50.75 - 52.50 56 1.25 1 1/8 53.75 260
purchaser
1219 1423 31.8 73.0 1289.1 - 1333.5 56 32 1 1/8 1365.3 117
54 62.5 1.38 3.12 57.25 - 59.00 68 1.25 1 1/8 60.25 325
1372 1588 34.9 79.4 1454.2 - 1498.6 68 32 1 1/8 1530.4 146
60 68.5 1.62 3.62 63.25 - 65.00 72 1.25 1 1/8 66.25 440
1524 1740 41.3 92.1 1606.6 - 1651.0 72 32 1 1/8 1682.8 198
66 75.5 1.75 4.00 69.50 - 71.62 72 1.38 1 1/4 73.00 575
1676 1918 44.5 101.6 1765.3 - 1819.2 72 35 1 1/4 1854.2 259
72 81.5 2 4.50 75.50 - 77.62 80 1.38 1 1/4 79.00 725
1829 2070 50.8 114.3 1917.7 - 1971.7 80 35 1 1/4 2006.6 326
1
Alternate designation: 50 lb PRESSURE AT 100˚F (38˚C). “Nominal Size” column, with pipe or vessel thickness in the 0.25" (6.4 mm) to 0.5" (12.7
2 mm) range.
Blind Flanges available upon application. 4
3 These flanges can also be supplied in any other material that can be forged or rolled.
When ordering these flanges specify thickness and O.D. of the pipe or component with
which they will be used. Pressure ratings are based on I.D. of pipe or vessel as listed in • 37 •
LARGE DIAMETER
CLASS 1755
WELDING NECK &
SLIP-ON FLANGES1
4
ASTM A-105 & A181-CLASS 60
FLANGE LENGTH THRU DIA. OF DRILLING APPROX.
FLANGE THICKNESS HUB DIA. OF HUB AT DIA. OF DIA. DIA. OF WEIGHT
OUTSIDE WELDING WELDING HUB AT POINT OF RAISED NO. OF OF BOLT BOLT WELDING
3
NOMINAL DIA. NECK SLIP-ON BORE NECK SLIP-ON BASE WELDING FACE HOLES HOLES DIA. CIRCLE NECK SLIP-ON
SIZE O C C B2 Y Y X A2 R K
26 31.5 1.38 1.38 3.38 2.75 27.62 29.00 28 .88 3/4 29.88 125 110
660 800 34.9 34.9 85.7 69.9 701.7 736.6 28 23 3/4 758.8 56 50
28 33.5 1.38 1.38 3.38 2.75 29.62 31.00 28 .88 3/4 31.88 130 120
711 851 34.9 34.9 85.7 69.9 752.5 787.4 28 23 3/4 809.6 59 54
30 35.75 1.38 1.38 3.62 2.75 31.88 33.25 36 .88 3/4 34.12 145 135
762 908 34.9 34.9 92.1 69.9 809.6 844.6 36 23 3/4 866.8 65 61
32 37.75 1.38 1.38 3.62 2.75 33.88 32.25 36 .88 3/4 36.12 165 145
813 959 34.9 34.9 92.1 69.9 860.4 895.4 36 23 3/4 917.6 74 65
34 40.25 1.50 1.75 3.75 3.38 35.88 37.38 36 1 7/8 38.38 190 205
864 1023 38.1 44.5 95.3 85.7 911.2 949.3 36 26 7/8 974.7 86 92
36 42.25 1.50 1.75 3.75 3.38 37.88 39.38 36 1 7/8 40.38 210 215
914 1074 38.1 44.5 95.3 85.7 962.2 1000.1 36 26 7/8 1025.5 95 97
38 44.25 1.75 2.00 4.12 3.75 39.88 41.38 36 1 7/8 42.38 235 255
965 1124 44.5 50.8 104.8 95.3 1012.8 1050.9 36 26 7/8 1076.3 106 115
40 46.25 1.75 2.00 4.12 4.00 41.88 43.38 40 1 7/8 44.38 250 275
1016 1175 44.5 50.8 104.8 101.6 1063.6 1101.7 40 26 7/8 1127.1 113 124
42 49 2.00 2.38 4.50 4.38 44.12 45.75 40 1.12 1 46.88 345 370
As As
1067 1245 50.8 60.3 114.3 111.1 1120.8 1162.1 40 29 1 1190.6 155 167
44 51 2.00 2.38 4.50 4.38 46.12 47.75 40 1.12 1 48.88 365 385
specified specified
1118 1296 50.8 60.3 114.3 111.1 1171.6 1212.9 40 29 1 1241.4 164 173
46 53 2.00 2.38 4.50 4.62 48.12 49.75 40 1.12 1 50.88 380 410
by by
1168 1347 50.8 60.3 114.3 117.5 1222.4 1263.7 40 29 1 1292.2 71 185
48 55 2.25 2.62 4.88 4.88 50.12 51.75 44 1.12 1 52.88 425 455
purchaser purchaser
1219 1397 57.2 66.7 123.8 123.8 1273.2 1314.5 44 29 1 1343.0 191 205
50 57 2.25 2.62 4.88 4.88 52.12 53.75 44 1.12 1 54.88 455 475
1270 1448 57.2 66.7 123.8 123.8 1324.0 1365.3 44 29 1 1393.8 205 214
52 59.5 2.62 3.00 5.38 5.38 54.25 56.00 44 1.25 1 1/8 57.25 550 605
1321 1512 66.7 76.2 136.5 136.5 1378.0 1422.4 44 32 1 1/8 1454.2 248 272
54 61.5 2.62 3.00 5.38 5.38 56.25 58.00 44 1.25 1 1/8 59.25 590 625
1372 1562 66.7 76.2 136.5 136.5 1428.8 1473.2 44 32 1 1/8 1505.0 266 281
60 67.5 2.75 3.12 5.75 5.88 62.25 64.00 48 1.25 1 1/8 65.25 675 725
1524 1715 69.9 79.4 146.1 149.2 1581.2 1625.6 48 32 1 1/8 1657.4 304 326
66 73.5 3.12 4.00 6.12 .688 68.50 70.00 56 1.25 1 1/8 71.25 825 1020
1676 1867 79.4 101.6 155.6 174.6 1739.9 1778.0 56 32 1 1/8 1809.8 371 459
72 80 3.62 5.00 6.62 8.00 74.50 76.50 64 1.25 1 1/8 77.75 1060 1400
1829 2032 92.1 127.0 168.3 203.2 1892.3 1943.1 64 32 1 1/8 1974.9 477 630
84 94 3.00 5.00 7.00 8.50 88.00 90.12 72 1.38 1 1/4 91.50 1550 2225
2134 2388 76.2 127.0 177.8 215.9 2235.2 2289.2 72 35 1 1/4 2324.1 698 1001
96 106 3.5 5.00 7.50 9.00 100.0 102.12 88 1.38 1 1/4 103.50 1975 2575
2438 2693 88.9 127.0 190.5 288.6 2540.0 2594.0 88 35 1 1/4 2628.9 889 1159
1
Blind Flanges are available upon application.
4
These flanges can also be furnished in any other material that can be forged
2
When ordering, specify thickness and O.D. of pipe vessel to which flange is or rolled.
to be welded.
5
Alternate designation, 150 lb. WSP. at 750˚F (399˚C).
3
Sizes are INSIDE diameters of pipe or shell used with Welding Neck
Flanges, and NOMINAL outside diameters of pipe or shell used with Slip-on
Flanges. INCHES POUNDS
LARGE DIAMETER
CLASS 300 5
WELDING NECK &

SLIP-ON FLANGES1
4
ASTM A-105 & A181- CLASS 60
FLANGE LENGTH THRU DIA. OF DRILLING APPROX.
FLANGE THICKNESS HUB DIA. OF HUB AT DIA. OF DIA. DIA. OF WEIGHT
OUTSIDE WELDING WELDING HUB AT POINT OF RAISED NO. OF OF BOLT BOLT WELDING
3
NOMINAL DIA. NECK SLIP-ON BORE NECK SLIP-ON BASE WELDING FACE HOLES HOLES DIA. CIRCLE NECK SLIP-ON
SIZE O C C B2 Y Y X A2 R K
26 32.75 2.50 2.50 5.00 4.50 27.88 29.50 28 1.12 1 30.62 250 230
660 832 63.5 63.5 127.0 114.3 708.0 749.3 28 29 1 777.9 113 104
28 34.75 2.50 2.50 5.00 4.50 29.88 31.50 28 1.12 1 32.62 265 255
711 883 63.5 63.5 127.0 114.3 758.8 800.1 28 29 1 828.7 119 115
30 37 2.62 2.62 5.25 4.75 32.12 33.75 32 1.12 1 34.88 310 290
762 940 66.7 66.7 133.4 120.7 816.0 857.3 32 29 1 885.8 140 131
32 39 2.75 2.75 5.50 5.00 34.12 35.75 36 1.12 1 36.88 340 325
813 991 69.9 69.9 139.7 127.0 866.8 908.1 36 29 1 936.6 153 146
34 41 2.88 2.88 5.75 5.12 36.12 37.75 40 1.12 1 38.88 385 350
864 1042 73.0 73.0 146.1 130.2 917.6 958.9 40 29 1 987.4 173 158
36 43.75 3.12 3.12 6.13 5.62 38.5 40.25 40 1.25 1 1/8 41.50 475 460
914 1112 79.4 79.4 155.6 142.9 977.9 1022.4 40 32 1 1/8 1054.1 214 207
38 45.75 3.12 3.12 6.13 5.62 40.5 42.25 40 1.25 1 1/8 43.50 520 485
965 1162 79.4 79.4 155.6 142.9 1028.7 1073.2 40 32 1 1/8 1104.9 234 218
40 47.75 3.25 3.25 6.25 5.88 42.5 44.25 44 1.25 1 1/8 45.50 550 525
1016 1213 82.6 82.6 158.8 149.2 1079.5 1224.0 44 32 1 1/8 1155.7 248 236
As As
42 50 3.50 3.50 6.50 6.12 44.75 46.50 48 1.25 1 1/8 47.75 650 625
1067 1270 88.9 88.9 165.1 155.6 1136.7 1181.1 48 32 1 1/8 1212.9 293 281
specified specified
44 52.75 3.75 3.75 6.75 6.75 46.75 48.88 44 1.38 1 1/4 50.25 770 760
1118 1340 95.3 95.3 171.5 171.5 1187.5 1241.4 44 35 1 1/4 1276.4 347 342
by by
46 54.75 4.25 4.25 7.25 7.25 48.75 50.88 48 1.38 1 1/4 52.25 895 880
1168 1391 108.0 108.0 184.2 184.2 1238.3 1292.2 48 35 1 1/4 1327.2 403 396
purchaser purchaser
48 56.75 4.25 4.25 7.25 7.25 50.75 52.88 48 1.38 1 1/4 54.25 925 925
1219 1442 108.0 108.0 184.2 184.2 1289.1 1343.0 48 35 1 1/4 1378.0 416 416
52 61.5 4.25 - 7.50 - 55 57.25 52 1.5 1 3/8 58.75 1075 -
1321 1562 108.0 - 190.5 - 1397.0 1454.2 52 35 1 3/8 1492.3 484 -
54 63.5 4.50 4.75 7.75 8.25 57 59.25 52 1.5 1 3/8 60.75 1225 1160
1372 1613 114.3 120.7 196.9 209.6 1447.8 1505.0 52 35 1 3/8 1543.1 551 522
60 69.5 4.50 5.00 8.00 8.50 63 65.25 60 1.5 1 3/8 66.75 1325 1470
1524 1766 114.3 127.0 203.2 215.9 1600.2 1657.4 60 35 1 3/8 1695.5 596 662
66 77 4.00 - .50 - 70 72.38 60 1.62 1 1/2 74.00 1680 -
1676 1956 101.6 - 215.9 - 1778.0 1838.3 60 42 1 1/2 1879.6 756 -
72 83 4.00 - 9.00 - 76 78.38 72 1.62 1 1/2 80.00 1875 -
1829 2109 101.6 - 228.6 - 1930.4 1990.7 72 42 1 1/2 2032.0 844 -
84 96.5 5.00 - 10.00 - 89 91.50 80 1.75 1 5/8 93.25 2950 -
2134 2451 127.0 - 254.0 - 2260.6 2324.1 80 45 1 5/8 2368.6 1328 -
96 109.25 6.25 - 11.25 - 101.25 103.88 84 1.88 1 3/4 105.75 4300 -
2438 2775 158.85 - 285.8 - 2571.8 2638.4 84 48 1 3/4 2686.1 1935 -
1
Blind Flanges are available upon application.
4
These flanges can also be furnished in any other material that can be forged
2
When ordering, specify thickness and O.D. of pipe vessel to which flange is or rolled.
to be welded.
5
Alternate designation, 300 lb. WSP. at 750˚F (399˚C).
3
Sizes are INSIDE diameters of pipe or shell used with Welding Neck
Flanges, and nominal OUTSIDE diameters of pipe or shell used with Slip-on
Flanges.
INCHES POUNDS
AWWA C207-55 HUB FLANGES2
ASTM A181-CLASS 60
FLANGE LENGTH THRU DIA. OF HUB DIA. OF APPROX.
FLANGE THICKNESS C HUB Y AT BASE X HOLES WEIGHT
DIA. OF
OUTSIDE BORE NO. OF BOLT
NPS3 DIA. CLASS CLASS DIA. CLASS CLASS CLASS CLASS HOLES CIRCLE CLASS CLASS CLASS CLASS
DN O B&D E P B&D E B&D E K B D&E B&D E
6 11 .56 1.00 1.25 1.56 7.56 7.56 8 9.50 .75 .88 14 19
150 280 14.3 25.4 31.8 39.7 192.1 192.0 8 241.3 20 23 6.3 9
8 13.5 .56 1.25 1.25 1.75 9.69 9.69 8 11.75 .75 .88 18 32
200 343 14.3 31.8 31.8 44.5 246.1 246.0 8 298.5 20 23 8 14.5
10 16 .69 1.19 1.25 1.94 12.00 12.00 12 14.25 .75 1 27 42
250 407 17.5 30.2 31.8 49.2 304.8 304.8 12 362.0 20 26 12 19
12 19 .69 1.25 1.25 2.19 14.38 14.38 12 17.00 .75 1 41 65
300 483 17.5 31.8 31.8 55.6 365.1 365.1 12 431.8 20 26 18.5 29
14 21 .75 1.38 1.25 2.25 15.75 15.75 12 18.75 .88 1.12 45 86
350 534 19.1 34.9 31.8 57.2 400.1 400.0 12 476.3 23 29 20 39
16 23.5 .75 1.44 1.25 2.50 18.00 18.00 16 21.25 .88 1.12 57 92
400 597 19.1 36.5 31.8 63.5 457.2 457.2 16 559.8 23 29 25.5 42
18 25 .75 1.56 1.25 2.69 19.88 19.88 16 22.75 .88 1.25 59 118
450 635 19.1 39.7 31.8 68.3 504.8 504.8 16 577.9 23 32 26.5 53
20 27.5 .75 1.69 1.25 2.88 22.00 22.00 20 25.00 .88 1.25 68 153
500 699 19.1 42.9 31.8 73.0 558.8 558.8 20 635.0 23 32 31 69
22 29.5 1 1.81 1.75 3.12 24.25 24.25 20 27.25 .88 1.38 75 177
550 750 25.4 46.0 44.5 79.4 616.0 616.0 20 692.2 23 35 34 80
As
24 32 1 1.88 1.75 3.25 26.12 26.12 20 29.50 .88 1.38 117 212
600 813 25.4 47.6 44.5 82.6 663.6 663.6 20 749.3 23 35 53 96
specified
26 34.25 1 2.00 1.75 3.38 28.50 28.50 24 31.75 .88 1.38 126 235
650 870 25.4 50.8 44.5 85.7 723.9 723.9 24 806.5 23 35 57 106
by
28 36.5 1 2.06 1.75 3.44 30.50 30.75 28 34.00 .88 1.38 139 273
700 927 25.4 52.4 44.5 87.3 774.7 781.1 28 863.6 23 35 63 123
purchaser
30 38.75 1 2.12 1.75 3.50 32.50 32.75 28 36.00 1 1.62 152 310
750 985 25.4 54.0 44.5 88.9 825.5 831.9 28 914.4 26 42 68 140
32 41.75 1.12 2.25 1.75 3.62 34.75 35.00 28 38.50 1 1.62 208 370
800 1061 28.6 57.2 44.5 92.1 882.7 889.0 28 977.9 26 42 94 167
36 46 1.12 2.38 1.75 3.75 38.75 39.25 32 42.75 1 1.62 235 460
900 1169 28.6 60.3 44.5 95.3 984.3 997.0 32 1085.9 26 42 106 207
40 50.75 1.12 2.50 1.75 3.88 43.00 43.75 36 47.25 1 1.62 281 527
1000 1289 28.6 63.5 44.5 98.4 1092.2 1111.3 36 1200.2 26 42 127 259
42 53 1.25 2.62 1.75 4.00 45.00 46.00 36 49.50 1.12 1.62 327 660
1100 1347 31.8 66.7 44.5 101.6 1143.0 1168.4 36 1257.3 29 42 147 297
48 59.5 1.38 2.75 2.50 4.12 51.00 52.25 44 56.00 1.12 1.62 420 800
1200 1512 34.9 69.9 63.5 104.8 1295.4 1327.3 44 1422.4 29 42 189 360
60 73 1.5 3.12 2.75 4.50 63.00 65.25 52 69.25 1.38 1.88 645 1275
1500 1855 38.1 79.4 69.9 114.3 1600.2 1657.4 52 1759.0 35 48 291 574
72 86.5 1.5 3.50 2.75 5.00 75.00 78.50 60 82.50 1.38 1.88 855 1950
1800 2197 38.1 88.9 69.9 127.0 1905.0 1993.9 60 2095.5 35 48 385 878
96 113.25 2.0 4.25 3.25 5.75 100.0 102.75 68 108.5 1.88 2.38 1730 3250
2400 2877 50.8 108.0 82.6 146.1 2540.0 2609.9 68 2755.9 48 61 779 1463
CLASS B FLANGES have a water service rating at atmospheric temperature sizes NPS 6 to NPS 12 (DN 150 to DN 300) inclusive, 175 psi; sizes larger
of 86 psi. These flanges have the same outside diameter, bolt circle and than NPS 12 (DN 300) 150 psi. These flanges have the same diameter and
number of bolts as ASME/ANSI B16.1 (25 psi cast-iron pipe flanges and drilling as Class 125 cast-iron flanges. (ASME/ANSI B16.1).
flanged fittings). CLASS E FLANGES have a water service rating at atmospheric temperature
In sizes NPS 48 (DN 1200) and under they have the same bolts, and in sizes of 275 psi. These flanges have the same diameter and drilling as Class 125
over NPS 48 (DN 1200) they use larger bolts than specified by this 25 psi cast-iron flanges (ASME/ANSI B16.1). In sizes NPS 24 (DN 600) and smaller
standard. they also match ASME/ANSI B16.5 150 psi standard for steel flanges.
They also have the same outside diameter, bolt circle, and number of bolts as All Flanges: Carbon steel bolts should be used. Cloth-inserted rubber gaskets
ASME/ANSI B16.1 (125 psi cast-iron pipe flanges and flanged fittings), but .06" (1.6 mm) thick should be used and should extend from the I.D. of flange
use smaller bolts. to at least the inside edge of the bolt holes.
CLASS D FLANGES have a water service rating at atmospheric temperature;
1
Can also be furnished in A181 CLASS 70 and A-105, or any other material
3
that can be forged or rolled. For sizes other than those shown full information is available upon request.
2
Ring and Blind flanges to match AWWA Hub flanges are available upon
application.
• 40 •
LARGE DIAMETER
PIPE LINE FLANGES
CLASS 150 (PN 20)
WELDING NECK & BLIND
2
ASTM A-105
HUB DIA. DRILLING APPROX.
FLANGE FLANGE LENGTH HUB AT POINT RAISED NO. OF DIA. DIA. FILLET WEIGHT
OUTSIDE THICKNESS THRU DIA. OF FACE BOLT OF BOLT OF BOLT RADIUS WELDING
NPS DIA. (MIN.)2 HUB AT BASE WELDING DIA. HOLES HOLES CIRCLE (MIN.) NECK BLIND
DN O C Y1 X A R r
26 34.25 2.69 4.75 26.62 26.00 29.50 24 1.38 31.75 .38 300 677
650 870 68.5 121 675 660 749 24 35 806 10 136 307
28 36.50 2.81 4.94 28.62 28.00 31.50 28 1.38 34.00 .44 315 833
700 925 71.5 125 725 711 800 28 35 863 11 143 378
30 38.75 2.94 5.38 30.75 30.00 33.75 28 1.38 36.00 .44 360 963
750 985 74.5 137 780 762 857 28 35 914 11 163 437
32 41.75 3.18 5.69 32.75 32.00 36.00 28 1.62 38.50 .44 435 1200
800 1060 81.0 144 830 813 914 28 41 978 11 197 544
34 43.75 3.25 5.88 34.75 34.00 38.00 32 1.62 40.50 .50 465 1342
1110 82.5 149 380 863 965 32 41 1029 13 211 609
36 46.00 3.56 6.18 36.75 36.00 40.25 32 1.62 42.75 .50 520 1540
900 1170 90.5 157 935 914 1022 32 41 1086 13 236 698
38 48.75 3.44 6.19 39.00 38.00 42.25 32 1.62 45.25 .50 778 1780
1240 87.4 157 990 965 1073 32 41 1150 13 353 807
40 50.75 3.56 6.44 41.00 40.00 44.25 36 1.62 47.25 .50 831 1992
1000 1290 90.5 164 1040 1016 1124 36 41 1200 13 377 903
42 53.00 3.81 6.75 43.00 42.00 47.00 36 1.62 49.50 .50 966 2332
1100 1345 97.0 171 1090 1067 1194 36 41 1257 13 438 1058
44 55.25 4.00 7.00 45.00 44.00 49.00 40 1.62 51.75 .50 1058 2656
1405 102.0 178 1145 1118 1245 40 41 1314 13 480 1205
46 57.25 4.06 7.31 47.12 46.00 51.00 40 1.62 53.75 .50 1131 2903
1455 103.0 186 1195 1168 1295 40 41 1365 13 513 1317
48 59.50 4.25 7.56 49.12 48.00 53.50 44 1.62 56.00 .50 1248 3276
1200 1510 108.0 192 1250 1219 1359 44 41 1422 13 566 1486
50 61.75 4.38 8.00 51.25 50.00 55.50 44 1.88 58.25 .50 1351 3605
1570 111.0 203 1300 1270 1410 44 48 1480 13 613 1635
52 64.00 4.56 8.25 53.25 52.00 57.50 44 1.88 60.50 .50 1508 4043
1300 1625 116.0 210 1355 1321 1460 44 48 1537 13 684 1834
54 66.25 4.75 8.50 55.25 54.00 59.50 44 1.88 62.75 .50 1667 4521
1400 1685 121.0 216 1405 1372 1511 44 48 1594 13 756 2051
56 68.75 4.88 9.00 57.38 56.00 62.00 48 1.88 65.00 .50 1817 4981
1745 124.0 229 1455 1422 1575 48 48 1651 13 824 2259
58 71.00 5.06 9.25 59.38 58.00 64.00 48 1.88 67.25 .50 2006 5540
1805 129.0 235 1510 1473 1626 48 48 1708 13 910 2513
60 73.00 5.19 9.44 61.38 60.00 66.00 52 1.88 69.25 .50 2108 6000
1500 1855 132.0 240 1560 1524 1676 52 48 1759 13 956 2722
1
Includes .06" (1.5mm) raised face.
2
Materials covered in this Standard are as in ASME/ANSI B16.5 except nickel
based alloys are excluded.
3
Bore diameter as specified by Purchaser.
INCHES POUNDS
LARGE DIAMETER
CLASS 300 (PN 50) 3
ASME B16.47 SERIES A

2
ASTM A-105
FLANGE THICKNESS3 HUB DIA. DRILLING APPROX.
FLANGE LENGTH HUB AT POINT RAISED NO. OF DIA. DIA. FILLET WEIGHT
OUTSIDE WELDING THRU DIA. OF FACE BOLT OF BOLT OF BOLT RADIUS WELDING
NPS DIA. NECK BLIND HUB AT BASE WELDING DIA. HOLES HOLES CIRCLE (MIN.) NECK BLIND
DN O C E Y1 X A R r
26 38.25 3.12 3.31 7.25 28.38 26.00 29.50 28 1.75 34.50 .38 615 1116
650 970 79.5 84.0 184 720 660 749 28 44 876 10 279 506
28 40.75 3.38 3.56 7.75 30.50 28.00 31.50 28 1.75 37.00 .44 750 1362
700 1035 85.5 90.5 197 775 711 800 28 44 940 11 340 618
30 43.00 3.62 3.75 8.25 32.56 30.00 33.75 28 1.88 39.25 .44 858 1590
750 1090 92.0 95.0 210 825 762 857 28 48 997 11 390 721
32 45.25 3.88 3.94 8.75 34.69 32.00 36.00 28 2.00 41.50 .44 960 1862
800 1150 98.5 100 222 880 813 914 28 51 1054 11 435 845
34 47.50 4.00 4.12 9.12 36.88 34.00 38.00 28 2.00 43.50 .50 1110 2134
1205 102 105 232 935 863 965 28 51 1105 13 504 968
36 50.00 4.12 4.38 9.50 39.00 36.00 40.25 32 2.12 46.00 .50 1223 2586
900 1270 105 111 241 990 914 1022 32 54 1168 13 560 1173
38 46.00 4.25 4.25 7.12 39.12 38.00 40.50 32 1.62 43.00 .50
1170 108 108 181 995 965 1029 32 41 1092 13
40 48.75 4.50 4.50 7.62 41.25 40.00 42.75 32 1.75 45.50 .50
1000 1240 114 114 194 1050 1016 1086 32 44 1156 13
42 50.75 4.69 4.69 7.88 43.25 42.00 44.75 32 1.75 47.50 .50
1100 1290 119 119 200 1100 1067 1137 32 44 1206 13
44 53.25 4.88 4.88 8.12 45.25 44.00 47.00 32 1.88 49.75 .50
1355 124 124 206 1150 1118 1194 32 48 1264 13
46 55.75 5.06 5.06 8.50 47.38 46.00 49.00 28 2.00 52.00 .50
1415 129 129 216 1205 1168 1245 28 51 1321 13
48 57.75 5.25 5.25 8.81 49.38 48.00 51.25 32 2.00 54.00 .50
1200 1465 133 133 224 1255 1219 1314 32 51 1372 13
50 60.25 5.50 5.50 9.12 51.38 50.00 53.50 32 2.12 56.25 .50
1530 140 140 232 1305 1270 1359 32 54 1429 13
52 62.25 5.69 5.69 9.38 53.38 52.00 55.50 32 2.12 58.25 .50
1300 1580 144 144 238 1355 1321 1410 32 54 1480 13
54 65.25 6.00 6.00 9.94 55.50 54.00 57.75 28 2.38 61.00 .50
1400 1660 152 152 252 1410 1372 1467 28 60 1549 13
56 67.25 6.06 6.06 10.25 57.62 56.00 59.75 28 2.38 63.00 .50
1710 154 154 260 1465 1422 118 28 60 1600 13
58 69.25 6.25 6.25 10.50 59.62 58.00 62.00 32 2.38 65.00 .50
1760 159 159 267 1515 1473 1575 32 60 1651 13
60 71.25 6.44 6.44 10.75 61.62 60.00 64.00 32 2.38 67.00 .50
1500 1810 164 164 273 1565 1524 1626 32 60 1702 13
1
2
Materials covered in this Standard are as in ASME/ANSI B16.47 except
nickel based alloys are excluded.
3
INCHES POUNDS
LARGE DIAMETER
PIPE LINE FLANGES
3
CLASS 400 (PN 68)
ASME B16.47 SERIES A
2
ASTM A-105
DN O C E Y1 X A R r
26 38.25 3.50 3.88 7.62 28.62 26.00 29.50 28 1.88 34.50 .44 769 1226
650 970 89.0 98.5 194 725 660 749 28 48 876 11 349 556
28 40.75 3.75 4.12 8.12 30.81 28.00 31.50 28 2.00 37.00 .50 902 1483
700 1035 95.0 105 206 785 711 800 28 51 940 13 409 673
30 43.00 4.00 4.38 8.62 32.94 30.00 33.75 28 2.12 39.25 .50 1025 1760
750 1090 102 111 219 835 762 857 28 54 997 13 465 798
32 45.25 4.25 4.56 9.12 35.00 32.00 36.00 28 2.12 41.50 .50 1188 2036
800 1150 108 116 232 890 813 914 28 54 1054 13 539 924
34 47.50 4.38 4.81 9.50 37.19 34.00 38.00 28 2.12 43.50 .56 1340 2374
1205 111 122 241 945 863 965 28 54 1105 14 608 1077
36 50.00 4.50 5.06 9.88 39.38 36.00 40.25 32 2.12 46.00 .56 1520 2756
900 1270 114 129 251 1000 914 1022 32 54 1168 14 689 1250
38 47.50 4.88 4.88 8.12 39.50 38.00 40.5 32 1.88 44.00 .56
1205 124 124 206 1005 965 1035 32 48 1118 14
40 50.00 5.12 5.12 8.50 41.50 40.00 43.00 32 2.00 46.25 .56
1000 1270 130 130 216 1055 1016 1092 32 51 1175 14
42 52.00 5.25 5.25 8.81 43.62 42.00 45.00 32 2.00 48.25 .56
1100 1320 133 133 224 1110 1067 1143 32 51 1226 14
44 54.50 5.50 5.50 9.18 45.62 44.00 47.25 32 2.12 50.50 .56
1385 140 140 233 1160 1118 1200 32 54 1283 14
46 56.75 5.75 5.75 9.62 47.75 46.00 49.50 36 2.12 52.75 .56
1440 146 146 244 1215 1168 1257 36 54 1340 14
48 59.50 6.00 6.00 10.12 49.88 48.00 51.50 28 2.38 55.25 .56
1200 1510 152 152 257 1265 1219 1308 28 60 1403 14
50 61.75 6.19 6.25 10.56 52.00 50.00 53.62 32 2.38 57.50 .56
1570 157 159 268 1320 1270 1362 32 60 1460 14
52 63.75 6.38 6.44 10.88 54.00 52.00 55.62 32 2.38 59.50 .56
1300 1620 162 164 276 1370 1321 1413 32 60 1511 14
54 67.00 6.69 6.75 11.38 56.12 54.00 57.88 28 2.62 62.25 .56
1400 1700 170 171 289 1425 1372 1470 28 67 1581 14
56 69.00 6.88 6.94 11.75 58.25 56.00 60.12 32 2.62 64.25 .56
1755 175 176 298 1480 1422 1527 32 67 1632 14
58 71.00 7.00 7.12 12.06 60.25 58.00 62.12 32 2.62 66.25 .56
1805 178 181 306 1530 1473 1527 32 68 1683 14
60 74.25 7.31 7.44 12.56 62.38 60.00 64.38 32 2.88 69.00 .56
1500 1885 186 189 319 1585 1524 1527 32 73 1753 14
1
Does not include .25" (6.5mm) raised face.
2
Material covered in this Standard are as in ASME/ANSI B16.5 except nickel based alloys are excluded.
3
4
These flanges can also be supplied in any material that can be forged or rolled.
INCHES POUNDS
LARGE DIAMETER
PIPE LINE FLANGES
CLASS 600 (PN 100) 3

ANSI/ASME B16.47 SERIES A
2
ASTM A-105
DN O C E Y1 X A R r
26 40.00 4.25 4.94 8.75 29.44 26.00 29.50 28 2.00 36.00 .50 963 1734
650 1015 108 125 222 748 660 749 28 51 914 13 437 786
28 42.25 4.38 5.19 9.25 31.62 28.00 31.50 28 2.12 38.00 .50 1120 1029
700 1075 111 132 235 803 711 800 28 54 965 13 508 916
30 44.50 4.50 5.50 9.75 33.94 30.00 33.75 28 2.12 40.25 .50 1232 2398
750 1130 114 140 248 862 762 857 28 54 1022 13 559 1088
32 47.00 4.62 5.81 10.25 36.12 32.00 36.00 28 2.38 42.50 .50 1500 2815
800 1195 117 148 260 917 813 914 28 60 1080 13 680 1277
34 49.00 4.75 6.06 10.62 38.31 34.00 38.00 28 2.38 44.50 .56 1580 3206
1245 121 154 270 973 863 965 28 60 1130 14 717 1454
36 51.75 4.88 6.38 11.12 40.62 36.00 40.25 28 2.38 47.00 .56 1750 3744
900 1315 124 162 283 1032 914 1022 28 60 1194 14 794 1698
38 50.00 6.00 6.12 10.00 40.25 38.00 41.50 28 2.38 45.75 .56
1270 152 156 254 1022 965 1054 28 60 1162 14
40 52.00 6.25 6.38 10.38 42.25 40.00 43.75 32 2.38 47.75 .56
1000 1320 159 162 264 1073 1016 1111 32 60 1213 14
42 55.25 6.62 6.75 11.00 44.28 42.00 46.00 28 2.62 50.50 .56
1100 1405 168 171 279 1125 1067 1168 28 67 1283 14
44 57.25 6.81 7.00 11.38 46.50 44.00 48.25 32 2.62 52.50 .56
1455 173 178 289 1181 1118 1226 32 67 1327 14
46 59.50 7.06 7.31 11.81 48.62 46.00 50.25 32 2.62 54.75 .56
1510 179 186 300 1235 1168 1276 32 67 1391 14
48 62.75 7.44 7.69 12.44 50.75 48.00 52.50 32 2.88 57.50 .56
1200 1595 189 195 316 1289 1219 1283 32 73 1467 14
50 65.75 7.75 8.00 12.94 52.88 50.00 54.50 28 3.12 60.00 .56
1670 198 203 329 1343 1270 1384 28 79 1524 14
52 67.75 8.00 8.25 13.25 54.88 52.00 56.50 32 3.12 62.00 .56
1300 1720 203 210 337 1394 1321 1435 32 79 1575 14
54 70.00 8.25 8.56 13.75 57.00 54.00 58.75 32 3.12 64.25 .56
1400 1780 210 217 349 1448 1372 1492 32 79 1632 14
56 73.00 8.56 8.88 14.25 59.12 56.00 60.75 32 3.38 66.75 .62
1855 217 225 362 1502 1422 1543 32 86 1695 16
58 75.00 8.75 9.12 14.56 61.12 58.00 63.00 32 3.38 68.75 .62
1905 222 232 370 1552 1473 1600 32 86 1746 16
60 78.50 9.19 9.56 15.31 63.38 60.00 65.25 28 3.62 71.75 .69
1500 1995 233 243 389 1610 1524 1657 28 92 1822 17
1
2
Materials covered in this Standard are as in ASME/ANSI B16.5 except nickel
based alloys are excluded.
3
INCHES POUNDS
LARGE DIAMETER
PIPE LINE FLANGES
3 2
CLASS 900 (PN 150)
ANSI/ASME B16.47 SERIES A
4
ASTM A-105
DN O C E Y1 X A R r
26 42.75 5.50 6.31 11.25 30.50 26.00 29.50 20 2.88 37.50 .44 1614 2423
650 1085 140 160 286 775 660 749 20 73 952 11 732 1099
28 46.00 5.62 6.75 11.75 32.75 28.00 31.50 20 3.12 40.25 .50 1894 3012
700 1170 143 171 298 832 711 800 20 79 1022 13 859 1366
30 48.50 5.88 7.18 12.25 35.00 30.00 33.75 20 3.12 42.75 .50 2196 3564
750 1230 149 183 311 889 762 857 20 79 1086 13 996 1617
32 51.75 6.25 7.62 13.00 37.25 32.00 36.00 20 3.38 45.50 .50 2628 4286
800 1315 159 194 330 946 813 914 20 86 1156 13 1192 1944
34 55.00 6.50 8.06 13.75 39.62 34.00 38.00 20 3.62 48.25 .56 3100 5207
1395 165 205 349 1006 864 965 20 92 1226 14 1407 2362
36 57.50 6.75 8.44 14.25 41.88 36.00 40.25 20 3.62 50.75 .56 3535 6003
900 1460 171 214 362 1064 914 1022 20 92 1289 14 1603 2723
38 57.50 750 8.50 13.88 42.75 38.00 43.25 20 3.62 50.75 .75
1460 190 216 352 1073 965 1099 20 92 1289 19
40 59.50 7.75 8.81 14.31 44.38 40.00 45.75 24 3.62 52.75 .81
1000 1510 197 224 364 1127 1016 1162 24 92 1340 21
42 61.50 8.12 9.12 14.62 46.31 42.00 47.75 24 3.62 54.75 .81
1100 1560 206 232 37 1176 1067 1213 24 92 1391 21
44 64.88 8.44 9.56 15.38 48.62 44.00 50.00 24 3.88 57.62 .88
1650 214 243 391 1235 1118 1270 24 98 1464 22
46 68.25 8.88 10.06 16.18 50.88 46.00 52.50 24 4.12 60.50 .88
1735 225 256 411 1292 1168 1334 24 105 1537 22
48 70.25 9.19 10.38 16.50 52.88 48.00 54.50 24 4.12 62.50 .94
1200 1785 233 264 419 1343 1219 1384 24 105 1588 24
1
2
Materials covered in this Standard are as in ASME/ANSI B16.5, except
nickel based alloys are excluded.
3
INCHES POUNDS
LARGE DIAMETER
STEEL FLANGES
CLASS 150 (PN 20) AND
CLASS 300 (PN 50)
WELDING NECK
ASTM A-1052
HUB DIA. DRILLING
RAISED AT POINT LENGTH
3
NO. DIA. OF
FLANGE 3
FLANGE FACE OF HUB DIA. THRU FILLET OF DIA. OF BOLT APPROX.
NPS DIAMETER THICKNESS DIA. BORE WELDING AT BASE HUB RADIUS HOLES HOLES CIRCLE WEIGHT
DN O C R B A X Y r K
CLASS 150
26 30.94 1.62 28.00 26.06 26.94 3.50 .38 36 .88 29.31 139
650 786 41.3 711.2 662.0 684.2 88.9 9.5 36 22.2 744.5 63
28 32.94 1.75 30.00 28.06 28.94 3.75 .38 40 .88 31.31 163
700 837 44.4 762.0 712.8 735.0 95.2 9.5 40 22.2 795.3 74
30 34.94 1.75 32.00 30.06 31.00 3.94 .38 44 .88 33.31 176
750 887 44.4 812.8 763.6 787.4 100.0 9.5 44 22.2 846.1 80
32 37.06 1.81 34.00 32.06 33.06 4.25 .38 48 .88 35.44 203
As
800 941 46.0 863.6 814.4 839.8 108.0 9.5 48 22.2 900.1 92
34 39.56 1.94 36.25 34.06 35.12 4.34 .38 40 1.00 37.69 249
specified
850
4
1005 49.2 920.8 865.2 892.2 110.3 9.5 40 25.4 957.3 113
36 41.62 2.06 38.25 36.06 37.19 4.62 .38 44 1.00 39.75 284
by
900 1057 52.4 971.6 916.0 944.6 117.5 9.5 44 25.4 1009.6 129
42 48.25 2.31 44.50 42.12 43.38 5.25 .44 48 1.12 46.12 406
Customer
1100 1226 58.7 1130.3 1070.0 1101.7 133.4 11.1 48 28.6 1171.6 184
48 54.81 2.56 50.75 48.12 49.50 5.88 .44 44 1.25 52.56 509
1200 1392 65.1 1289.0 1222.4 1257.3 149.2 11.1 44 31.8 1335.1 231
54 61.00 2.81 56.75 54.12 55.62 6.38 .44 56 1.25 58.75 632
1400 1549 71.4 1441.4 1374.8 1412.9 161.9 11.1 56 31.8 1492.2 287
60 67.94 3.00 63.00 60.12 61.81 7.06 .56 52 1.38 65.44 855
1500 1726 76.2 1600.2 1527.2 1570.0 179.4 14.3 52 34.9 1662.1 388
CLASS 300
26 34.12 3.50 29.00 26.19 27.62 5.69 .56 32 1.38 31.62 399
650 867 88.9 736.6 665.2 701.7 144.5 14.3 32 34.9 803.3 181
28 36.25 3.50 31.00 28.19 29.75 5.88 .56 36 1.38 33.75 447
700 921 88.9 787.4 716.0 755.6 149.2 14.3 36 34.9 857.2 203
30 39.00 3.69 33.25 30.25 32.00 6.22 .56 36 1.50 36.25 590
750 991 93.7 844.6 768.4 812.8 158.0 14.3 36 38.1 920.8 268
32 41.50 4.06 35.50 32.25 34.00 6.62 .62 32 1.62 38.50 727
As
800 1054 103.2 901.7 819.2 863.6 168.3 15.9 32 41.3 977.9 330
34 43.62 4.06 37.50 34.25 36.12 6.81 .62 36 1.62 40.62 787
specified
850
4
1108 103.2 952.5 870.0 917.6 173.0 15.9 36 41.3 1031.9 357
36 46.12 4.06 39.75 36.25 38.00 7.12 .62 32 1.75 42.88 893
by
900 1172 103.2 1009.6 920.8 965.2 181.0 15.9 32 44.4 1089.0 405
42 52.50 4.69 46.00 42.31 44.00 8.06 .62 36 1.88 49.00 1252
Customer
1100 1334 119.1 1168.4 1074.7 1117.6 204.8 15.9 36 47.6 1244.6 568
48 59.50 5.06 52.25 48.31 50.31 8.81 .62 40 2.00 55.75 1611
1200 1511 128.6 1327.2 1227.1 1277.9 223.8 15.9 40 50.8 1416.0 731
54 65.88 5.38 58.25 54.31 56.50 9.44 .62 48 2.00 62.12 1979
1400 1673 136.5 1479.6 1379.5 1435.1 239.7 15.9 48 50.8 1578.0 898
60 73.94 5.94 65.00 60.31 62.94 10.69 .69 40 2.38 69.44 2890
1500 1878 150.8 1651.0 1531.9 1598.6 271.5 17.5 40 60.3 1736.7 1311
1
Also available in Class 75. Particulars upon request. Materials extracted from API STANDARD 605, Second Edition, October 1978, Large Diameter
Carbon Steel Flanges (Nominal Pipe Size 26 to 60, inclusive; Classes 75, 150 and 300) Tables 3,
2
Materials covered in this Standard are the same as ASME/ANSI B-2 and B-3, reprinted by courtesy of the American Petroleum Institute.
B16.5 except nickel base alloys are excluded.
3
Flange Thickness C and Length through Hub Y includes .06" INCHES POUNDS
(1.6 mm) raised face.
FOR DETAILS OF WELDING BEVEL, REFER TO PAGE 48.
IDENTIFICATION
CCTF flanges, where the size and design permits, are marked with the following identification data in
accordance with ASME/ANSI B16.5:
Trade Mark or name Nominal size
Primary service pressure B16 (ANSI designation)
Material designation Heat code
FORGED FLANGE TOLERANCES

Millimetres in brackets
DIMENSION WELDING NECK SLIP-ON & LAP

& SOCK. WELD SOCK. WELD. THREADED JOINT BLIND
Outside Diameter
1
Flange O.D. 24 or less (609.6) ± .06 (1.6) ±.06 (1.6) ±.06 (1.6 ±.06 (1.6) ±.06 (1.6)
Flange O.D. over 24 (609.6) ±.12 (3.2) ±.12 (3.2) ±.12 (3.2) —.12 (3.2) ±.12 (3.2)
Bore NPS 10 (DN 250) & less ±.03 (0.8)2 +.03 (0.8)4 +.03 (0.8) +.03 (0.8) —
—0 —0 —0 —
NPS 12 - 18 (DN 300 - 450) ±.06 (1.6)2 +.06 (1.6)4 +.06 (1.6) +.06 (1.6) —
—0 —0 —0 —
NPS 20 (DN 500) & over + .12 (3.2)2 +.06 (1.6)4 +.06 (1.6) +.06 (1.6) —
—.06 (1.6) —0 —0 —0 —
Flange Thickness NPS 18 (DN 450) & less) +.12 (3.2) +.12 (3.2) +.12 (3.2) +.12 (3.2) +.12 (3.2)
—0 —0 —0 —0 —0
NPS 20 (DN 500) & over +.19 (4.8) +19 (4.8) +.19 (4.8) +.19 (4.8) +.19 (4.8)
—0 —0 —0 —0 —0
Raised Face Diameter .06 (1.6) raised face ±.03 (0.8) ±.03 (0.8) ±.03 (0.8) — ±.03 (0.8)
.25 (6.4) raised face ±.02 (0.5) ±.02 (0.5) ±.02 (0.5) — ±.02 (0.5)
Drilling Bolt circle ±.06 (1.6) ±.06 (1.6) ±.06 (1.6) ±.06 (1.6) ±.06 (1.6)
Bolt hole spacing ±.03 (0.8) ±.03 (.08) ±.03 (0.8) ±.03 (0.8) ±.03 (0.8)
Eccentricity 3
NPS 2 1/2 (DN 65) & less .03 (0.8) max. .03 (0.8) max. .03 (0.8) max. .03 (0.8) max. —
NPS 3 (DN 80) & larger .06 (1.6) max. .06 (1.6) max. .06 (1.6) max. .06 (1.6) max. —
Length Thru Hub NPS 4 & less ±.06 — — — — —
(Welding Neck Flanges) NPS 5 to 10 +.06 -.12 — — — — —
NPS 12 & larger +.12 -.18 — — — — —
Diameter of Hub at Base
1
NPS 12 (DN 300) & less ±.09 (2.4) ±.09 (2.4) ±.09 (2.4) ±.09 (2.4) —
-.06 (1.6) -.06 (1.6) -.06 (1.6) -.06 (1.6) —
NPS 14 (DN 350) & over) ±.12 (3.2) ±.12 (3.2) ±.12 (3.2) ±.12 (3.2) —
Diameter of Hub at Bevel NPS 5 (DN 125) & less +.09 (2.4) — — — —
-.03 (0.8) — — — —
NPS 6 (DN 150) & over +.16 (4.0) — — — —
±.03 (0.8) — — — —
Thickness of Hub at Bevel All sizes of welding neck Minimum, —12 1/2& of matching nominal pipe wall thickness
1
These tolerances not covered by ASME/ANSI B16.5.
2
Welding Neck and Socket Welding small bore.
3
Between bolt circle diameter and machined facing diameter.
4
Socket Welding Socket.
• 47 •
WELDING BEVELS - (WELD NECK FLANGES NO BACKING RINGS)
ASME/ANSI B16.5, ASME B16.47 ASME/ANSI B16.5, ASME B16.47
Nominal pipe wall thickness T = 0.88 (22.2 mm) max. T = more than 0.88" (22.4 mm)
For wall thickness less than 0.19 in. (4.8) mm) for
carbon and ferritic alloy steel, and 0.125 in. (3.2 mm)
austenitic alloy steel, ends may be cut square or
slightly chamfered at manufacturer’s option.
Although great care has been taken in compiling the

information contained in this catalogue, CCTF does
not accept responsibility for the consequences of any
Catalogue Section 3 errors, nor for the effects of any subsequent changes
made by the various sources of data.
• 48 •
FSF

Forged Flanges Catalog

Uploaded by

Copyright:

Available Formats

Forged Flanges Catalog

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Forged Flanges Catalog

Uploaded by

Copyright:

Available Formats

FORGED STEEL FLANGES

1. Holes accurately drilled for ease of assembly.

2. Spot facing ensures seating of fasteners true and square.

3. Grain flow controlled for maximum strength.

4. Smooth accurate bore for unrestricted flow.

5. Machined bevel and land facilitate good welding.

6. All faces machined within tolerances to ensure true alignment.

7. Full identification of size, pressure class, material and heat code.

ORIFICE FLANGES CLASS 300 - 1500 (PN 50-250)

LONG WELDING NECKS ..........................................................................................Page 33

LARGE DIAMETER FLANGES

ENGINEERING AND DESIGN DATA

MSS, API, AWWA, ANSI AND CSA STANDARDS

*From the SI designations, Diamètre Nominal and Pression Nominale.

DRILLING DIAMETER OF HUB APPROXIMATE WEIGHT

For bevel of Welding Neck, see page 48.

DRILLING DIAMETER OF HUB APPROXIMATE WEIGHT

DRILLING DIAMETER OF HUB APPROXIMATE WEIGHT

DRILLING DIAMETER OF HUB APPROXIMATE WEIGHT

For bevel of Welding Neck, see page 48.

DRILLING DIAMETER OF HUB APPROXIMATE WEIGHT

For bevel of Welding Neck, see page 48.

REDUCING FLANGES ASME/ANSI B16.5 —

DRILLING DIAMETER OF HUB APPROXIMATE WEIGHT

CLASS 150 — 2500 (PN 20 - 420)

Same as flange outside diameter, see pages 6 - 19.

.25 .25 .25 .25

■ Not included in ASME/ANSI B16.36.

*Details of Ring Joint facings are given on page 30.

FOR FURTHER DETAILS, REFER TO PAGE 4 “OTHER TYPES”.

DRILLING BOLTING DIAMETER APPROXIMATE WEIGHT

The tapped metering holes are drilled as follows:

DRILLING BOLTING DIAMETER APPROXIMATE WEIGHT

The tapped metering holes are drilled as follows:

DRILLING BOLTING DIAMETER APPROXIMATE WEIGHT

NOMINAL PIPE SIZE GROOVE DIMENSIONS DIAMETER OF RAISED FACE K

NOMINAL PIPE SIZE GROOVE DIMENSIONS DIAMETER OF RAISED FACE K

LENGTH THRU HUB WEIGHTS

FLANGE LENGTH DIAMETER NO. DIAMETER DIA. OF

WELDING NECK &

ASME B16.47 SERIES A

WELDING NECK & BLIND

FORGED FLANGE TOLERANCES

DIMENSION WELDING NECK SLIP-ON & LAP

ASME/ANSI B16.5, ASME B16.47 ASME/ANSI B16.5, ASME B16.47

Although great care has been taken in compiling the

You might also like