CK138 Single-door controller user manual [Ver 2.

5]

Product Description: If you have normal DC 12V Power supply only, please connect it
This single-door controller is a series of independent ones that are this way:
developed for the control of exits of office building, intellectual
building, residential area, public channel of building, through which
user can open door with respondent card, can open with pass code or
can with both respondent card and pass code, then a simple door
controller system solution program is made. Product character:
working voltage: DC 12V
unlock current: ≤1.5A
static current: ≤1A
available card quantity: 800 pieces
Maximum card-read distance: 15cm-20cm
RF card type: EM or EM compatible card
℃～70℃
working temperature: -40
working moisture: 10%～90% 1. 1st pin connects power anode+12V and 2nd pin connects
size: 117×117×21mm cathode, attention: Anode and cathode must not be wrongly
connected, or controller is burnt.
Special attention: 2. 5th and 6th pins connect switch, and 7th and 8th pins contact
1. please strictly do per user manual. door bell without different between anode and cathode.
2. please don’t do with power on! Need pay more special attention 3. to keep door controller work steadily, please don’t connect
on anode and cathode. electric lock directly with controller.

How to assemble: programming setup way:

Unpack cross-screw that fixes faceplate and motherboard, then take original management pass word is 12345 and user password is 8888.
off motherboard and get it assembled on side wall which is at the 1.enter programming
exit, with attention on vertical orientation. push*=>input management pass word=>push#
alert: 1. please ensure to switch off power before connecting lines
and switch on power after all lines being connected well! 2 function setup(under programming circumstance)
Please be sure that power voltage is 12v and that anode& (1) modify management password:
cathode are in place! push 0=>input new management password =>push#=>
again input new management password =>push#
note: password is 1-10 digital number.
circuit diagram: (2) add user card
If you have a specific power supply with timer control, please Method 1:
connect it as below diagram: push 1 =>read card =>push#
note:.
if need add more than 1 card, needn’t re-input 1 and directly
read card, then finally push # button .
Method 2:
Push 1 => Input 10 digits card / keyfob number => push #
Note:
This 10 digits unique number should be printed on the card
or keyfob. (Input the first 10 digits if the number you found
is more than 10 digits)
Method 3:
Read “Master Card for adding” => read new card => read
“Master Card for adding” again

-1-
 CK138 Single-door controller user manual [Ver 2.5]

(3) 4 ways to delete user card Note: in general, please don’t change the jumper wire setup.
A. Delete all user card: push2=>push0000=>push #
B. Delete the card read: push2=>read card=>push# Factory Reset procedure for door controller:
C. Delete lost card: push2=>10 digits card / keyfob number 1. switch off power and keep pushing RESET(holding it)
=>push# 2. switch on the power and press RESET for 3 seconds, then unhold
D. Read “Master Card for erasing” => read card => read it and reset procedure is completed.
“Master card for erasing” Status: the door controller goes into working status with 1 sound of
(4) setup for open mode buzzer.
A. Open with reading valid card: push 300=>push# Note:
B..Open with reading valid card and password: push 301=> 1. This procedure only change system password to default
push# programming password, 12345, and user password 8888, others
C. open with reading valid card or entrying correct password: remain the same.
push302=>push# 2. normally please don’t use initialization back to default unless user
note: original setup is 302 for reading valid card or input forgets password.
password to open door.
(5) setup for open door time Setting “Master cards”:
push4=>X X=>push# 1. switch off power and keep pushing RESET(holding it)
note: XX is during 00-99, measure unit is second and origin is 3 2. switch on the power and remain holding the RESET button.
seconds, and 0 is added for less than 2 digitals. 3. Read 2 cards
(6) how to modify use password 4. Unhold the Reset button. You will hear a “beep” sound.
push 5=>input 1 new password with 1-10 digit number=>push# Note:
=>again input 1 new password with 1-10 digit number=>push# The first card would be “Master card for adding”, while the second
to save card is “Master card for erasing”.
(7) Save setup and exit from programming Packing list:
push button * to save access controller 1 set
note: above any setup after completing must be saved within 1 User manual 1 piece
minute by pushing * Plastic insert for fixed and screw 1 bag

how to use: Attachment 1: description for signal light

open by card: under normal working environment, door can be issue type red light green light
Normal working circumstance glitter once per second
opened with 1 valid card.
read valid card/correct password, light
open by card and password: door can be opened if correct password unlock

is input 10 seconds after card is read. open door and push button, then light
unlock
open by password: door can be opened by inputting user password. wrong password Light
Attention: the door controller supports 3 modes, opening by card, by invalid card Light
entry valid button Light
password and by card and password.
alert to prevent from unpacking Glitter
programming status Light glitter quickly
description for setup of jumper wire: entry correct programming code Light light
entry wrong programming code Light
1. J1 jumper wire:
Attachment2:description for buzzer sound
2nd and 3rd pins of J1 are connected and PUSH exports the signal
issue type buzzer
of keeping open, with N.O as default. normal working status
1st and 2nd pins of J1 are connected and PUSH exports the signal read valid card/correct password, then unlock. 2 short- toot
open door and push button, then unlock 1 short-toot
of keeping close.
wrong password 1 short toot, then 1 long toot
2.J2 jumper wire invalid card 1short toot, then 1 long toot
2nd and 3rd pins of J2 are connected and PUSH exports GND low entry valid button sort toot
programming status 2 short toots
voltage signal, with GND as default.
entry correct programming code 2 short toots
1st and 2nd pins of J2 are connected, PUSH exports 12V high entry wrong programming code 3 short toots

voltage signal.
-2-