Architectural Design (Vector) v2
Architectural Design (Vector) v2
CONTENT:
Triangulation
Characteristics of vector Active Structures
Plane trusses Vierendeel trusses
Uses of trusses
Analysis OF TRUSSES
Method of truss
Roof trusses
Secondary stresses
Open web joist
Space Trusses
Plane truss a Verse space truss
Our Reference is based on the Book : Structures in Architecture by Prof. Harbhajan Singh
Various parts of a "Lean- To" roof are depicted in incase pent roofs, "Purlins"
provide lateral rigidity to trusses. In case of Bridges, the bridge deck may be
carried at the level of Top Chord or Bottom chord. In practice for road bridges,
Deck is carried at the level of bottom card so that truss also acts as a parapet of
bridge.
either at the level of Top or Bottom chord. Diagonal members of will develop
tension and diagonals will be in compression.
Roof trusses
Introduction-
In the context of trusses, Roof trusses are extensively used for roofs of
warehouses, workshops and auditoriums or other such buildings requiring large
column free spaces.
Aim-
To provide large column free spaces.
Materials-
Roofing material generally of AC (Asbestos Cement) sheets or CGI (Corrugated
Galvanized Sheets) is supported on purlins, which in turn are supported on
Principal Rafters of Trusses.
• Spacing of Trusses - Closely spaced trusses will ensure lighter sections for
purlins there by reducing their cost but would increase the cost of trusses'
due to increase in number of trusses. On the other hand widely spaced
trusses will reduce number of trusses but would increase the cost of purlins
and truss support structures like columns etc.
Spacing should be decided in such a manner that the total cost is kept as low
as possible, for spans up to 35m spacing is kept between one third to one
fifth of truss span, and for spans greater than 35 m spacing is kept as one
third of truss span.
• Pitch of Truss- The ratio of height of truss to its span is called pitch of truss.
Following slopes are generally provided:
(a) Trusses carrying snow load = 1/4
(b) (b) Trusses carrying CGI sheets = 1/6
(c) (c) Trusses with AC sheets 1/12
BOOK: MARLON W. BROEKEMEIER, P.E. and JAMES M. FISHER,
Ph.D., P.E.
OBJECTIVE:
● To determine the stability and determinacy of space trusses
● To determine member forces of space trusses using tension coefficient
analysis
TYPE OF SPACE TRUSSES
1. Simple Space Truss
2. Compound Space Truss
3. Complex Space Truss
DETERMINACY & STABILITY Due to three dimensions, there will be
three equations of equilibrium for each joint. (Fx = 0; Fy = 0; Fz = 0) • The
external stability of the space truss requires that the support reactions keep the
truss in force and moment equilibrium. • Generally, the least number of required
reactions for stable and externally determinate is SIX If r < 6 Unstable If r > 6
Externally Indeterminate
Plane Trusses
Plane Trusses are the type of truss in which all the members of the Truss lie on
the same plane. Planar trusses are typically used in parallel to form roofs and
bridges.
Space Truss
Space Truss are the type of trusses whose members are oriented in all 3
dimensions. It is a rigid, lightweight structure constructed from interlocking
struts in a geometric pattern. Space trusses can be used to span large areas with
few interior supports.
• It resists force on all planes
• Its basic form is a tetrahedron structure
• All joints are in the form of pinned connections
• Even concrete can be used for its creation
• The total no. of members can be calculated using m=3n-6, where m is the
total no. of members and n is the total no. of joints