lOMoARcPSD|10030848

Chapter 6 Solutions, Power Electronics (Hart)

Electrónica de Potencia (Universidad de las Américas Puebla)

StuDocu is not sponsored or endorsed by any college or university

Downloaded by Juan Jesus Ramirez Rodriguez ([email protected])
 lOMoARcPSD|10030848

CHAPTER 6 SOLUTIONS
5/17/10
6-1)
Po = Vo I o = Vo I s ; Ps = Vs I s

Po Vo I o Vo
h= = =
Ps Vs I s Vs

6-2)
P 100
Io = = = 3.33 A.
Vo 30
Po 100
a ) Ps = Vs I o = (100)(3.33) = 333 W .; h = = = 30%
Ps 333
b) PQ = VCE I o = (70)(3.33) = 233 W .
1 yr.=8760 Hr.; W = (233)(8760)=2044 kW-Hr,
c ) e.g., @10 cents/kW-Hr, cost = $204.40/yr.

6-3)
a ) Vo = Vs D = (100)(0.6) = 60 V .
b) Vo, rms = Vm D = (100) 0.6 = 77.5 V (see Example 2-4)
Vo2,rms 77.52
c) P = = = 600 W .
R 10
d ) Results are not dependent on frequency.

6-4)
a ) Vo = Vs D = (24)(0.65) = 15.6 V .
Vo 15.6
b) I L = I R = = = 1.56 A.
R 10
V 15.6 1
DiL = o (1 - D )T = -6
(1 - 0.65) = 2.18 A.
L 25(10) 100, 000
Di 2.18
I L ,max = I L + L = 1.56 + = 2.65 A.
2 2
Di 2.18
I L ,min = I L - L = 1.56 - = 0.47 A.
2 2

Downloaded by Juan Jesus Ramirez Rodriguez ([email protected])

 lOMoARcPSD|10030848

Vo (1 - D) 15.6(1 - 0.65)
c ) DVo = 2
= = 0.182
8LCf 8(25)(10)-6 (15)(10) -6 (100, 000)2
DVo
or = 1.17%
Vo

6-5)
a ) Vo = Vs D = 9 V .
b) I L = 1.8 A.; DiL = 2.4 A.
DiL
I L ,max = I L + = 3.0 A.
2
Di
I L ,min = I L - L = 0.6 A.
2
DVo
c) = 0.44%
Vo

6-6)
Vo
a) D = = 0.5
Vs
Po 125
b) I L = I R = = = 5 A.
Vo 25
DiL V
I L ,max = 6.25 A. � = 1.25; DiL = 2.5 A. = o (1 - D)T
2 L
V 25 1
L = o (1 - D)T = (1 - .5) = 50 m H .
DiL 2.5 100, 000
Vo 1- D
c) D = 5% = .005 =
Vo 8LCf 2
1- D 1 - .5
C= = = 25 m F .
�DVo � 2 8(.005)(50)(10) -6 (100, 000) 2
8 � �Lf
�Vo �

Downloaded by Juan Jesus Ramirez Rodriguez ([email protected])

 lOMoARcPSD|10030848

6-7)
Vo 1.5
a) D = = = 0.25
Vs 6
2
V 1.5 2 �0.5625 / 2 �
b) average : I L = I R = o = = 0.5 A. rms : I L ,rms = 0.5 + � � = 0.526 A.
R 3 � 3 �
DiL = 0.5625
�1 1 - D � �1 1 - .25 �
peak : I L ,max = Vo � + �= 1.5 � + -6 �= 0.781 A.
�R 2 Lf � �3 2(5)(10) (400,000) �
�1 1 - D �
I L,min = Vo � - �= 0.219 A.
�R 2 Lf �
Vo I R 1.5(0.5)
c ) Ps = Po � Vs I s = Vo I R � I s = = = 0.125 A.
Vs 6
d ) I D ,max = I L,max = 0.781 A.
I D = I o - I s = 0.5 - 0.125 = 0.375 A.

6-8)
Po 25
Io = I L = = = 1.25 A.
Vo 30
Vo 20
D= = = 0.667
Vs 30
DiL
I L,min = (0.25)(1.25) = 0.31 A. = I L -
2
DiL = ( I L - I L ,min )2 = (1.25 - 0.31)2 = 1.88 A.
Vo
DiL = (1 - D)T
L
V 1 20 1
L = o (1 - D) = ( 1 - .667 ) = 89 m H
DiL f 1.88 40000

Downloaded by Juan Jesus Ramirez Rodriguez ([email protected])

 lOMoARcPSD|10030848

6-9)
(1 - D) R
Lmin =
2f
Vo 20 20
D= ; Dmax = = 0.4; Dmin = = 0.33
Vs 50 60
Po 75 125
IL = IR = ; I R ,min = = 3.75 A.; I R ,max = 6.25 A.
Vo 20 20
Vo 202 202
R = ; Rmax = = 5.33 W; Rmin = = 3.20 W
P 75 125
(1 - Dmin ) Rmax (1 - .33)(5.33)
Lmin = = = 17.76 m H
2f 2(100, 000)

6-10)
(1 - D)( R)
Lmin = f = 200 kHz
2f

Vo=5 V

Vs, V D I, A. R, Ω Lmin, µH

10 0.5 0.5 10 12.5

10 0.5 1.0 5 6.25
16.7 (worst case, D = 1/3, R =
1/3
15 0.5 10 10)
15 1/3 1.0 5 8.33

(1 - Dmin ) Rmax
L=
2f

� 1�
1- �
� (10)
Lmin = � 3�
= 16.67 m H
2(200 k )

6-11) Example design:

Downloaded by Juan Jesus Ramirez Rodriguez ([email protected])

 lOMoARcPSD|10030848

Vo 15
D= = = 0.3125
Vs 48

Let f = 100 kHz ( for example)

�V � �15 �
Let DiL = 40% of I L = 0.40 � o �= 0.40 �8 �= 0.75 A
�R � � �

( Vs - Vo ) D ( 48 - 15) 0.3125
L= = = 137.5 m H
( DiL ) f ( 0.75) 100,000
1- D 1 - 0.3125
C= = = 12.5 m F
�DVo � 8 ( 150 ) 10-6 (0.005)100,000
8L � �f
�Vo �

Other values of L and C are valid if the inductor current is continuous with margin.

6-12) (Based on the example design in 6-11)

Vmax, switch = Vs = 48 V
Vmax, diode = Vs = 48 V
Imax, switch = ILmax = 1.5 + 0.75/2 = 1.875 A
Vo Io 15 ( 1.875 )
Iavg, switch = = = 0.586A
Vs 48
DT
1
�
2
Irms, switch = i (t)d t = 1.06 A (numerically)
L
T 0

Imax,diode = ILmax = 1.875 A

Iavg,diode =IL- Iavg,switch = 1.875 – 0.586 = 1.289 A

T
1
Irms,diode = �
T DT
i 2L (t)d t = 1.56 A (numerically)

6-13) Example design:

Downloaded by Juan Jesus Ramirez Rodriguez ([email protected])

 lOMoARcPSD|10030848

Vo 15
D= = = 0.625
Vs 24

Let f = 400 kHz ( for example)

Let DiL = 40% of I L = 0.40 ( 2 ) = 0.8 A

L=
( Vs - Vo ) D = ( 24 - 15) 0.625 = 17.6 m H
( DiL ) f ( 0.8) 400,000
1- D 1 - 0.625
C= = = 1.67 m F
�DVo � 8 ( 17.6 ) 10-6 (0.01)400,000
8L � �f
�Vo �

6-14) Example design:

Vo 12
D= = = 0.667
Vs 18

Let f = 200 kHz ( for example)

Po 10W
I L = Io = = = 0.833 A
Vo 12V

Let DiL = 40% of I L = 0.40 ( 0.833) = 0.333 A

L=
( Vs - Vo ) D = ( 18 - 12 ) 0.667 = 60 m H
( DiL ) f ( 0.333) 200,000
1- D 1 - 0.667
C= = = 3.5 m F
�DVo � -6 � 0.1 �
8L � �f 8 ( 60 ) 10 � � 200,000
�Vo � �12 �

Other values of L and C are valid if the inductor current is continuous with margin.

Downloaded by Juan Jesus Ramirez Rodriguez ([email protected])

 lOMoARcPSD|10030848

6-15)

n = 1 � V1 = 30.27
Using ac circuit analysis, Vo1 = 0.048 V = 2(0.048) = 0.096 V p - p
0.096 0.096
= = 0.48%
Vo 20
DVo
Using Eq. 6 -16, = 0.469%
Vo

The output voltage is mainly the dc term and the first ac term.

6-16)
a ) rC = 0.5 W, DiL = 2.88 A = DiC
DVo ,ESR = DiC rC = 2.88(0.5) = 1.44 V .
DVo 1.44
= = 8%
Vo 18
DVo
b) �0.5%
Vo
DVo 0.005(18)
DVo �DVo ,ESR = DiC rC � rC = = = 0.031 W
DiC 2.88
50(10) -6 50(10) -6 50(10) -6
rC = � C= = = 1600 m F .
C rC 0.031

6-17)

Downloaded by Juan Jesus Ramirez Rodriguez ([email protected])

 lOMoARcPSD|10030848

Vs 20
a ) Vo = = = 50 V .
1 - D 1 - .6
Vs 20
b) I L = = = 10 A.
(1 - D ) R (1 - .6) 2 (12.5)
2

Vs V DT 20 20(.6) / (200,000)
I max = 2
+ s = 2
+ = 13 A.
(1 - D ) R 2L (1 - .6) (12.5) 2(10)(10) -6
Vs V DT
I min = 2
- s = 7.0 A.
(1 - D ) R 2L
DVo D 0.6
c) = = = 0.6%
Vo RCf 12.5(40)(10) -6 (200,000)
Vo 50
d ) ID = Io = = = 4.0 A.
R 12.5

6-18)

Inductor current: (see Example 2-8)

2 2
�DI / 2 � �4.61/ 2 �
I L, rms = I + � L � = 102 + �
2
L � = 10.09 A.
� 3 � � 3 �

Capacitor current: (define t=0 at peak current)

Downloaded by Juan Jesus Ramirez Rodriguez ([email protected])

 lOMoARcPSD|10030848

1/2
� 1 �10 m s 25 m s �
�
-6 �� �
I C ,rms =� � ( - 4.61(10) 5
t + 8.3) 2
dt + ( - 4) 2
dt �
� = 4.97 A.
25(10)
� �
�
� � 0 10 m s �
�

6-19)

Vs V 5
Vo = � D = 1 - s = 1 - = 0.667
1- D Vo 15
Vo2 152
R= = =9 W
25 25
Vs 5
IL = = = 5 A.
(1 - D) R (1 - .667) 2 (9)
2

I L ,min = 0.5(5) = 2.5 A. � DI L = 5 A.

Vs DT 5(.667) / 300
DI L = = = 2.22 m H
DI L 5
D 0.667
From Eq. 6 - 27, C = = = 24.7 m F .
� Vo � 9(.01)(300, 000)
R�D �f
� Vo �

Downloaded by Juan Jesus Ramirez Rodriguez ([email protected])

 lOMoARcPSD|10030848

6-20) Example design:

Vs 12
D =1- = 1 - = 0.333
Vo 18

Vo2 182
R= = = 16.2 W
P 20
Vs 12
IL = 2
= = 1.67 A
(1- D) R ( 1 - .333) 2 16.2
Let f = 200 kHz

Let DiL = 40% of I L = 0.4 ( 1.67 ) = 0.667 A

Vs D 12 ( 0.333)
L= = = 30 m H
( DiL ) f (0.667)200,000
( Lmin for continuous current = 6 m H )

D 0.333
C= = = 20.6 m F
�DV � 16.2 ( 0.005 ) 200,000
R� o �f
�Vo �

6-21)
0.6
Using C = 48 m F , R = 50 W, ton = 0.6T = = 24 m s
25000
vo (t ) = Vo ,max e - t / RC
vo (24 m s ) = Vo ,max e -24/[(50)(48)] = Vo ,max ( 0.99005)
Vo ,max - vo (24 m s ) = DVo = Vo ,max - 0.99005Vo ,max �0.01Vo,max
DVo
= 0.01 = 1%
Vo

Downloaded by Juan Jesus Ramirez Rodriguez ([email protected])

 lOMoARcPSD|10030848

6-22)

6-23)
�D � � 0.6 �
a ) Vo = -Vs � �= -12 � = -18 V .
� 1- D � �1 - 0.6 �
�
Vs D 12(.6)
b) Eq. 6 - 31: I L = 2
= = 4.5 A.
R (1 - D) (10)(1 - .6) 2
Vs D V DT 12(.6) / 200, 000
I L ,max = 2
= s = 4.5 + = 6.3 A.
R (1 - D ) 2L 2(10)(10) -6
Vs D V DT
I L ,min = 2
- s = 2.7 A.
R (1 - D ) 2L
DVo D 0.6
c) = = = 0.015 = 1.5%
Vo RCf 10(20)(10)-6 (200, 000)

Downloaded by Juan Jesus Ramirez Rodriguez ([email protected])

 lOMoARcPSD|10030848

6-24)

Inductor current: (see Example 2-8)

2 2
�DI / 2 � �3.6 / 2 �
I L,rms = I + � L � = 4.52 + �
2
L � = 4.62 A.
� 3 � � 3 �

Capacitor current: For convenience, redefine t = 0 at the peak current. The current is then
expressed as

( )
iC ( t ) = 4.5 - 1.8 106 t A for 0 < t < 2m s

= -1.8 A for 2 m s < t < 5m s

T
1 2 1 1
T�
I rms = i (t ) dt T= = = 5 ( 10-6 ) = 5m s
0
f 200, 000

1/2
� 1 �2 m s 2
5m s �
�
I C , rms =� -6 ��
� �
4.5 - 1.8 ( 10 -6
) � dt + � ( - 1.8) 2
dt � = 2.30 A.
�
5(10) � � �
�
� �0 2 m s �
�
�

Downloaded by Juan Jesus Ramirez Rodriguez ([email protected])

 lOMoARcPSD|10030848

6-25)

Vo 36
a ) From Eq. 6-48, D = = = 0.6
Vs + Vo 24 + 36
Vs D 24(.6)
IL = = = 9 A. � I L ,min = 0.4(9) = 3.6 A.
R (1 - D) 10(1 - .6) 2
2

DI L = 2(9 - 3.6) = 10.8 A.

Vs DT 24(.6)
From Eq. 6-28, L = = = 13.3 m H
DI L 10.8(100, 000)

D 0.6
b) From Eq. 6-36, C = = = 120m F
�DVo � 10(0.005)(100,000)
R � �f
�Vo �

6-26) Example design:

Vo 50
Using Eq. (6-48), D= = = 0.556
Vs + Vo 40 + 50

P 75
Using Eq. (6-49), IL = = = 3.375 A.
Vs D 40 ( 0.556 )

Vo2 502
R= = = 33.3 W
P 75
Letting f = 100 kHz (designer's choice),

( 1 - D ) 2 R ( 1 - 0.556 ) 2 33.3
Lmin = = = 32.9 m H
2f 2 ( 100, 000 )

Choose L at least 25% larger than L min (41 m H). A common practice is to select L such that
Di L = 40% of I L = 0.40 ( 3.375 ) = 1.35 A. Using Eq. (6-45),

Vs D 40 ( 0.556 )
L= = = 165 m H
DiL f 1.35 ( 100, 000 )

D 0.556
Using Eq. (6-54), C= = = 16.7 m F
�DV � 33.3 ( 0.01) ( 100, 000 )
R � o �f
�Vo �

Downloaded by Juan Jesus Ramirez Rodriguez ([email protected])

 lOMoARcPSD|10030848

6-27) Example design:

Vo 15
Using Eq. (6-48), D= , D= = 0.556 for the 12-V source,
Vs + Vo 12 + 15

15
and D = = 0.455 for the 18-V source.
18 + 15

( 1 - D) 2 R
Using Lmin = , the worst case is for D = 0.455 for the 18-V source.
2f
( 1 - 0.455) 2 15
Letting f = 100 kHz (designer's choice), Lmin = = 22.3 m H
2 ( 100, 000 )

Choose L at least 25% larger than L min (28 m H).

Alternatively, a common practice is to select L such that Di L = 40% of I L .

Vo2 152
Il = = = 1.83 A
Vs RD 18 ( 15 ) ( 0.455 )

DiL = 0.40 ( 1.83) = 0.73 A. Using Eq. (6-45),

Vs D 18 ( 0.455 )
L= = = 112 m H (100 m H will be fine)
DiL f 0.73 ( 100, 000 )

D
Using Eq. (6-54), C= , so base C on D = 0.556, (12-V source):
�DV �
R � o �f
�Vo �
0.556
C= = 37 m F
15 ( 0.01) ( 100, 000 )

Downloaded by Juan Jesus Ramirez Rodriguez ([email protected])

 lOMoARcPSD|10030848

6-28) Using the equations

Vo
D=
Vs + Vo

Vo2
R=
P
2

Lmin =
( 1- D) R
2f
P
IL =
Vs D

D
C=
�DV �
R� o �f
�Vo �

and using f = 100 kHz (designer’s choice), results are shown in the table.

Vs, (V) P (W) D R (Ω) Lmin (µH) IL (A) C (µF)

10 10 0.545 14.4 14.9 1.83 37.9
10 15 0.545 9.6 9.9 2.75 56.8
14 10 0.462 14.4 20.9 1.55 32.1
14 15 0.462 9.6 13.9 2.32 48.1

The value of L should be based on Vs = 14 V and P = 10 W, where Lmin = 20.9 µH. Select the
value of L at least 25% larger than Lmin (26.1 µF). Using another common criterion of ΔiL = 40%
of IL, again for 14 V and 10 W, L = 104 µH.

The value of C is 56.8 µF for the worst case of Vs = 10 V and P = 10 W.

Downloaded by Juan Jesus Ramirez Rodriguez ([email protected])

 lOMoARcPSD|10030848

6-29)
�D � � 0.6 �
Vo = -Vs � �= -12 � = -18 V .
�
1- D � 1 - 0.6 �
� �
P V 2 R 27
I L2 = o = o = = 1.5 A.
-Vo -Vo 18
Po 27
I L1 = = = 2.25 A.
Vs 12
Vs D 12(.6)
DiL1 = = -6
= 0.14 A.
Lf 200 ( 10 ) (250,000)
Vs D
DiL 2 = = 0.29 A.
L2 f

6-30)
1 1
D= = = 0.333
V 20
1- s 1-
Vo -10
I L 2 = I o = 1 A.
Vo �10 �
I L1 = I L2 = � � (1) = 0.5 A.
Vs �20 �
VD VD 20(0.333)
DiL1 = s � L1 = s = = 1.33 mH
L1 f DiL1 f 0.10(.5)(100,000)
Vs D VD 20(0.333)
DiL 2 = � L2 = s = = 0.667 mH
L2 f DiL 2 f 0.10(1)(100,000)

Downloaded by Juan Jesus Ramirez Rodriguez ([email protected])

 lOMoARcPSD|10030848

6-31) Example design:

Vo D -30
=- = = -1.2 � D = 0.5455
Vs 1 - D 25

Po 60 Vs D 25 ( 0.5445 )
I L 2 ===� D==޳==2.0 A; iL 2 0.4(2.0) 0.4 A L2 341 m F
-Vo 30 DiL 2 f 0.4 ( 100,000 )

P 60 Vs D 25 ( 0.5445)
I L1 ===s�D==޳==
2.4 A; iL1 0.4(2.4) 0.48 A L1 284 m F
Vs 25 DiL1 f 0.48 ( 100,000 )

Let f = 100 kHz (designer's choice).

1- D 1 - 0.5455
C2 � = = 1.67 m F
�DVo � 2 ( 0.01) 8 341( (
10 -6
( ))
100,000 ) 2

� � 8L2 f
�Vo �
VC1 = Vs - Vo = 25 - ( -30 ) = 55 V � DvC1 = 0.05 ( 55 ) = 2.75 V
2
Using R = Vo2 / P = ( -30 ) / 60 = 15 W,

VD 30 ( 0.5455 )
C1 � o = = 3.97 m F
Rf DvC1 15 ( 100,000 ) 2.75

Downloaded by Juan Jesus Ramirez Rodriguez ([email protected])

 lOMoARcPSD|10030848

6-32)
Vo 12
D= = = 0.706
Vo + Vs 12 + 5

Vo 2 122
I L1 = = = 7.2A
Vs R 5(4)

Vs D (5)(0.706)
Di L1 = = = 3.53A
L1f 10(10)-6 (100,000)

3.53
I L1,max = 7.2 + = 8.96A
2
3.53
I L1,min = 7.2 - = 5.44A
2
Vo 12
I L2 = = = 3A
R 4
Vs D (5)(0.706)
Di L1 = = = 1.765A
L2f 20(10)-6 (100,000)

1.765
I L2,max = 3 + = 3.88A
2
1.765
I L2,min = 3 - = 2.12A
2

Downloaded by Juan Jesus Ramirez Rodriguez ([email protected])

 lOMoARcPSD|10030848

6-33)

Vs D 3.3(.7)
Vo = = = 7.7V
1 - D 1 - .7
Vo 2 7.7 2
I L1 = = = 3.6A
Vs R 3.3(5)

Vs D (3.3)(0.7)
Di L1 = = = 1.925A
L1f 4(10)-6 (300,000)

1.925
I L1,max = 3.6 + = 4.56A
2
1.925
I L1,min = 3.6 - = 2.64A
2
Vo 7.7
I L2 = = = 1.54A
R 5
Vs D (3.3)(0.7)
Di L1 = = = 0.77A
L 2 f 10(10)-6 (300,000)

0.77
I L2,max = 1.54 + = 1.925A
2
0.77
I L2,min = 1.54 - = 1.155A
2
Vo D (7.7)(.7)
DVC1 = DVC2 = = = 0.0719V
RCf 5(50)(10) -6 (300,000)

6-34) Equation (6-69) for the average voltage across the capacitor C1 applies:

VC1 = Vs .

When the switch is closed, the voltage across L2 for the interval DT is

v L2 = v C1

Assuming that the voltage across C1 remains constant at its average value of Vs

vL2 = VC1 = Vs (switch closed)

When the switch is open in the interval (1 - D)T,

vL2 = -Vo (switch open)

Downloaded by Juan Jesus Ramirez Rodriguez ([email protected])

 lOMoARcPSD|10030848

Since the average voltage across an inductor is zero for periodic operation,

(v L2, sw closed ) ( DT ) + ( v L2, sw open ) ( 1 - D) T = 0

Vs ( DT ) - Vo ( 1 - D ) T = 0
resulting in

�D �
Vo = Vs � �
�
1- D �

6-35)

Vo 2 62
I L1 = Is = = = 1.2A
Vs R (15)(2)

Vo 6
D= = = 0.286
Vo + Vs 6 + 15

Vs D (15)(0.286)
L1 = = = 35.7mH
( Di L1 )f 0.4(1.2)250,000

Vo 6
I L2 = I o = = = 3A
R 2
Vs D (15)(0.286)
L2 = = = 14.3mH
( Di L2 )f 0.4(3)250,000

VC2 = Vo = 6

Vo D D 0.286
DVC2 = DVo = or C2 = = = 28.6mF
RC 2f �DVo � 2(.02)250,000
R� � f
�Vo �
C1 = C2 = 28.6mF

Downloaded by Juan Jesus Ramirez Rodriguez ([email protected])

 lOMoARcPSD|10030848

6-36)
Vo 2.7
D= = = 0.231
Vo + Vs 2.7 + 9

2.7
R= = 2.7W
1
Vo 2 2.72
I L1 = = = 0.30A
Vs R 9(2.7)

Vs D 9(0.231)
L1 = = = 57.7mH
( Di L1 ) f 0.4(0.30)300,000
I L2 = I o = 1A

Vs D 9(0.231)
L2 = = = 14.2mH
( Di L2 ) f 0.4(1)300,000

6-37)
DiC = I L ,max = 2.7 A.
DVO , ESR = DiC rC = (2.7)(0.6) = 1.62 V .
DVO , ESR 1.62
= = 0.054 = 5.4%
VO 30
Worst case : DVO = DVO ,C + DVO , ESR = 0.3 + 1.63 = 1.92 V . = 6.4%

6-38)
Switch closed : vL = Vs - VQ
Switch open : vL = VO - VD
avg (vL ) = 0 : (Vs - VQ ) DT + (VO - VD )(1 - D)T = 0
�D �
\ VO = VD - (Vs - VQ ) � �
�
1- D �

Downloaded by Juan Jesus Ramirez Rodriguez ([email protected])

 lOMoARcPSD|10030848

6-39)
(1 - D) R L 2 f 97.5(10) -6 (2)(40000)
a ) Lmin - � Rmax = = = 12.5 W
2f 1- D 1 - .375
b) For R=20Ω, current is discontinuous:
� � � �
� 2D � � 2(0.375)
�
Vo = Vs � �= 48 � �= 21.4 V .
� 2 8L � � 2 8(97.5)(10) -6 �
�D + D + � �0.375 + (0.375) + �
� RT � � 20 / 40000 �
\ 18 �Vo �21.4 V .
(1 - D) R (1 - 0.375)(20)
c) Lf min = = = 6.25
2 2
6.25 6.25
Increase Lf min : e.g ., Lmin = = 157 m H or f min = = 64.1 kHz
40000 97.5 mH

6-40)
2 Lf 2(120)(10) -6 (25000)
a ) Rmax = = = 62.5 W for continuous current
D(1 - D ) 2 0.6(1-).6) 2
b) For R=100Ω, the current is discontinuous:
� 2 D 2 RT �
�
1+ 1+ �
Vo = Vs � L �
� 2 �
� �
� �
� 2(.6) 2 (100) / 25000 �
�1+ 1+ �
120(10) -6
Vo = 12 � �= 36 V .
� 2 �
� �
� �
� �
\ 30 �Vo �36 for 25 �R �100
4.8 4.8
c) Lf min = 4.8 � L > = 192 m H or f > = 40 kHz.
25000 120(10)-6

Downloaded by Juan Jesus Ramirez Rodriguez ([email protected])

 lOMoARcPSD|10030848

6-41) Discontinuous current for the buck-boost converter: Let DT be the time that the switch is
closed and D1T be the time that the switch is open and the current in the inductor is positive. For
a lossless converter, the output power is the same as the input power.

�I D �
Ps = Vs I s = Vs �max �
� 2 �
V DT
I max = s
L
2 2
V DT
Ps = s
2L
2
V
Po = o
R
Vs D T Vo2
2 2
=
2L R
Vo RT
=D
Vs 2L

6-42) When switches “1” are closed, C1 and C2 are connected in series, each having Vs/2 volts.
When the “1” switches are opened and the “2” switches are closed, Vo = Vs of the source plus
Vs/2 of C1, making Vo = 1.5Vs.

6-43)

Downloaded by Juan Jesus Ramirez Rodriguez ([email protected])

 lOMoARcPSD|10030848

20W

p(t) for the MOSFET

10W

0W

(1.000m,405.19m)
Average P = 405 mW

-10W
0.990ms 0.992ms 0.994ms 0.996ms 0.998ms 1.000ms
W(M1) AVG(W(M1))
Time

Downloaded by Juan Jesus Ramirez Rodriguez ([email protected])

 lOMoARcPSD|10030848

6-44) Simulate the buck converter of Example 6-1 using PSpice. (a) Use an ideal switch and ideal
diode. Determine the output ripple voltage. Compare your PSpice results with the analytic results
in Example 6-1. (b) Determine the steady-state output voltage and voltage ripple using a switch
with an on resistance of 2 Ω and the default diode model

Using Ron =0.01 for the switch and n=0.01 for the diode, the p-p ripple voltage is 93.83 mV.
93.83/20 = 0.469%, agreeing precisely with the analytical results.

With Ron = 2 ohms, the p-p ripple is 90 mV, with a reduced average value.

Downloaded by Juan Jesus Ramirez Rodriguez ([email protected])

 lOMoARcPSD|10030848

6-45)
Note that for each converter topology, the average voltage across each inductor is zero,
and the average current in each capacitor is zero.

Buck Converter:
Show from Eqs. (6-9) and (6-17)
Is
Vo = Vs D and Io =
D

From the averaged circuit of Fig. 6.33b,

Is
I L = Io = i c and Is = Dic � Io =
D
Vap = Vs and Vo = DVap � Vo = DVs

Boost Converter:
Show from Eqs. (6-27) and (6-28) that
Vs
Vo = and Io = Is ( 1 - D )
1- D

From the averaged circuit of Fig. 6.33c,

Vs
DVap = Vs - Vo and Vap = - Vo � Vo =
1- D
Io = -ic + Dic = ic ( D - 1) and Is = -ic � I o = Is ( 1 - D )

Downloaded by Juan Jesus Ramirez Rodriguez ([email protected])

 lOMoARcPSD|10030848

Buck-Boost Converter:
Show from Eqs. (6-47) and (6-49) and preceding equations that
�D �
Vo = -Vs � and Is = I L D
1- D �
� �

From the averaged circuit of Fig. 6.33d,

I L = ic and Is = Di c � Is = I L D

�D �
Vap = Vs - Vo and Vo = -DVap � Vo = -Vs �
1- D �
� �

Ćuk Converter:
Show from Eqs. (6-59) and (6-61) that
IL1 D �D �
= and Vo = -Vs �
I L2 1 - D 1- D �
� �
From the averaged circuit,

�D �
Vap = Vs - Vo and DVap = -Vo � Vo = -Vs �
1- D �
� �
I L1 D
i c = Di c + I L2 and I L1 = Di c � =
I L2 1 - D

Downloaded by Juan Jesus Ramirez Rodriguez ([email protected])