A6 Operation Instruction-160905

Download as pdf or txt
Download as pdf or txt
You are on page 1of 70

0

Contents
INTRODUCTION ............................................................................................................................. 2
A. Security Considerations ............................................................................................................... 3
B. Product Details ............................................................................................................................ 4
1.Specifications.......................................................................................................................... 4
2.Machine parts ......................................................................................................................... 4
3.Exploded drawing ................................................................................................................... 5
4.Tool List .................................................................................................................................. 6
C. Cura Software ............................................................................................................................. 9
1.Installation of Cura14.07 ......................................................................................................... 9
1.1 File location in the TF card ............................................................................................ 9
2. Cura Setting ......................................................................................................................... 18
2.1 Clear platform .............................................................................................................. 18
2.3 Layer height settings ................................................................................................... 23
D. Printing Operation ..................................................................................................................... 50
1.Display Introduction .............................................................................................................. 50
2. Filament Feeding ................................................................................................................. 53
2.1 Set Preheat ........................................................................................................................ 53
3. Platform Adjustment ............................................................................................................. 56
4. Printing ................................................................................................................................ 58
E. FAQ ........................................................................................................................................... 62
1. Z Axis Ajustment .................................................................................................................. 62
1. Nozzle blocking ................................................................................................................. 64
3.FAQ ...................................................................................................................................... 67

Ⅵ. Maintenance ............................................................................................................................. 68

Ⅶ. Maintenance Service Provision ................................................................................................ 69

1
INTRODUCTION

A6 FDM 3D printer can print CAD 3D printer model to real . A6 uses Acrylic to build

its frame while it uses linear bearings , belts and threaded rods to build X , Y , Z axis .

It enables A6 to print steadily with no vibration .

Note:

1. All statement included in this Instructions have been checked carefully , if any

typographical errors or misunderstanding , we have the final interpretation .

2. No noification if any update .

2
A. Security Considerations

To avoid danger when using 3D printer , please pay attention to precautions below .

Danger
During Operation , the maximum temeprature of nozzle can be 260 ℃ while hotbed

can be 100 ℃ . For your safety , during printing or cooling down , do not touch the

nozzle , hotbed and models under printing . Power works at 110V/220V 50HZ AC and

supply ground needed . Do not use other power supply , or it may cause components

damage , fire or electric shock . And we take no responsibility for this .

Warning
We suggest wering protective goggles when removing auxiliary support materials .

Some filaments will emit slight irritant gases , so we suggest to use 3D printer in a

ventilated environment .

Note: ABS filament will emit a bit toxic gases when it melts .

3
B. Product Details

1.Specifications
Model:A6 Nozzle diameter: 0.4mm
Layer thickness:0.1-0.3mm Machine size: 480*400*400mm
Printing speed:10-120mm/s Machine weight:7.6KG
X Y axis position accuracy:0.012mm Packing size:450*446*215mm
Z axis position accuracy:0.004m Gross weight:9.5KG
Printing material:ABS,PLA Build size:220*220*240mm
Material tendency:PLA LCD screen:12864 LCD
Filament diameter :1.75mm Offline printing:SD CARD
Software language:Multi-Language File format:STL、G-Code、OBJ
Function of support:automatically OS:windows(linux、mac)

Software: Cura Working condition:10-30℃,Humidity 20-50%

2.Machine parts

4
3.Exploded drawing

NO Part Name Quantity


1 Extruder Motor 1
2 Blower 1
3 Wind Mouth 1
4 Nozzle(0.4mm) 1
5 Heating Block 1
6 Throat 1
7 Fan Cover 1
8 Fan 1
9 Heat Sink 1
10 Extruder Seat 1
11 Bend Parts 1
12 Brass Wheel 1
13 U-Bearing 1
14 Briquetting 1
15 Spring 1
16 Heating Pipe 1
17 Limited Switch 1
Seat
18 Blower Seat 1
19 Limited Switch 1

5
4.Tool List

6
7
8
C. Cura Software

1.Installation of Cura14.07
a: Where can I find the software?

1) SD card with shipment; 2) download from Internet;

b: Installation process

1) From SD card with shipment

Insert SD card and open the file

1.1 File location in the TF card

1)Insert SD card , open the file

9
2) Download from Internet

Official Website:https://ultimaker.com/en/cura-software/list

Choose corresponding software to download

10
b.Software Installation Process

1. Installation
Positioning

2. Click Next

Choose 3 options below

1
2
3

4. Click Install

11
Please wait for installation

1.Click Next

12
1.Installation Success

2.Click to finish

Installation complete

Click Next

13
1.Choose to run Cura

2. Click to finish

Click Next

14
1.Choose other to customize

2.Choose this option

3.Click Next

15
1.Choose to customize

2.Click Next

16
This is A6 parameter

You can customize name here.

We default these data .


You can fill in according to
actual condition

Choose this option

DO NOT choose this option !!!

1.Click to finish

17
Now you have finished the installation. Next , enter Cura .

2. Cura Setting
2.1 Clear platform
Delete the dog. Two ways for you :

1.Move mouse to dog ,right click, click “delete object”.

18
2.Left click “File” , choose ”Clear platform”.

19
Switch to full settings
for parameter setting

20
Open file:A8 Cura 14.07.ini

Position of configuration file: Computer/SD card)/ configuration file for cura-14.07

(suggestion :keep this file copy to your computer)

21
After Loading,the basic and advanced
configuration will be changed to the A8
regular printing configuration.

If print once at a time , it will influence the printing


quality, even cause damage to priner. So please
choose “Printer at once”.

22
2.3 Layer height settings

Layer height:0.1mm cost long time but have the best


printing precision. 0.2mm cost half time compared to
0.1mm , but have general printing precision. 0.3 cost less
time with not good precision. It defaults 0.2mm.

Left:0.1mm Right:0.2mm
Layer height Layer height

Layer height setting

0.8mm

1.2mm
Shell thickness setting

2mm

23
The B
the le

Enab

Enable retraction to avoid filaments


leakage when nozzles move in
empty area

Bottom/Top thickness
Under the same
fill density

When fill density is less than 20%,


it’s easy for 0.6mm thickness to
cause hollow on the top. 1.2mm
normally won’t have this issue.
Bottom/Top thickness:

24
Bottom/Top thickness
setting

Fill Density
20%
Setting

50%

Fill Density: If strength requirement


is not so high , set 10% is ok.
Please improve fill density when
strength requirement gets higher.
Printing time will go up as well.

90%

Printing Speed set

This is default speed. If other se


it prints more accurately while th
takes more time.
High printing speed takes less tim
print accurately , making the mo
Normally 40-60 print speed is su

Pringting Tempe
setting

PLA filament temperature setting: nozzle:

ABS filament temperature setting: nozzle


25
Please set higher temperature of nozz
thickness is b
Please set lower temerature of nozzle
thickness is sm
Support type:Original
None Model

Attention: Normally we add support to complex model or model with vacant parts. It may
have influence on the surface if you choose everywhere. You’d better circle around the
model and try to avoid unnecessary support.

Support type setting Support type: Touching Support type: Everywhere


buildplate

26
27
None: no support

Brim:Touch with the adge

Support setting

Raft: Totally touch with the bottom


28
Attention: please choose None if the printing platform is ready and the high temperature
adhesive tape is good. Please choose Brim when the model is small . Choosing Raft makes it
difficult to seperate model from the platform

29
Attention: A6 use 1.75mm filament

Attention:
Flow is proportion of filament , we suggest to use 100
Increasing flow & decrease diameter has the similar
effect
Model surface gets many bumps when flow is too
big;model frame gets flimsy if flow is too small.

30
We suggest not to change
it , A6 default 0.4mm

We suggest not to change it ,


or use the date in the picture

We suggest 0.2mm to avoid initial layer tilt,0.3mm


is more easy to seperate from the platform.

Initial layer line proportion

“0” means using default speed

Min printing time for each layer. When the time is


less than 10 , it prints slower. It’s better to
decrease time when printing thin and long models.

We suggest not choose this when printing ABS.

31
Attention:Normally this option cannot be
changed , if changed ,it’s at your peril.

Attention:Normally this option cannot be


changed , if changed , it’s at your peril.

Starting
Ending
3.Expert Setting
code
code

32
33
1
2
3
4

1. The minimum length before retraction . Used to avoid frequent retraction. No need to
change.
2. Enable Combing: Digital for surface quality , the nozzle will try not to go through surface ,
that’s why Cura is better than Slic3r.
3. Minimum extrusion length , to avoid frequent extrusion.
4. The height extruder rise in the retraction . If you need to set this option , 2mm is suitable .

Printing route
Printing route
without Combing
with Combing

Go aside of the Go through the


surface surface

34
Skirt is to avoid extruder unfilled before printing , and it appears only when platform
attachment type is None. Normally “1” is ok . Change it to “0” when your model
reaches the maximum size , or the printing size will be too big.

Peripheral line quantity: 1 Peripheral line quantity: 1


Start distance: 3 Start distance: 3

35
1. To ensure the attachment of model to platform , fan won’t start at the beginning.
2-4. Fan speed min & max : If they are not equal , the soft ware will choose a suitable speed during
them.
5. Condition to choose cool head lift : When it’s printing with the minimum speed but still cannot
reach the minimum time , you need to choose cool head lift . But it may cause filament leak.

36
No solid infill top With solid infill top

37
No solid infill bottom With solid infill bottom

Infill coverlap: 20 Infill coverlap: 40

38
Structure types:lines Structure types:lines Structure types:grids
Infill covertap: 15 Infill covertap: 30 Infill covertap: 15
Distance X/Y: 0.7 Distance X/Y: 0.7 Distance X/Y: 0.7

These above are examples , you can set these options according to actual
requirements. The biggest progress Cura has made is the kinds of support
structure types , making it easier to seperate from the model.

39
It’s difficult to seperate if the distance between support and the supported place is too
close; The surface will be influenced if the distance is too far.
Different angle will generate different support , you can try the examples we provide
above which will have different effect.
60° 40 45° 30°
41
When choosing “Spiralize When choosing “Only follow
the outer contour” : Z axis mesh surface” : The nozzle
rises while X,Y axis moves , prints along the surface.
and only a hollow bottom
and a single layer of
surface.
Attention: The software defaults not open the option above , you’d better not turn it
on .

42
43
Brim line amount: 10 Brim line amount: 20

Guidance to use Brim if needed: Expert → Expert Settings → Support → Support


Types → Birm.
The images above are only for reference , please set the parameter according to
actual requirement.

44
Guidance to use Raft if needed: Expert → Expert Settings → Support → Support Types →
Raft.
The images above are only for reference , please set the parameter according to actual
requirement.

Load model Save the Gcode file Link to Youmagine

Model Display

Estimated Print
Time

Estimated Length of Filament

Scaling

Whirling Mirroring

Left click the model and you will see the


45 icon of “whirling, scaling, mirroring.
Left click to select model and move → move model.
Slide mouse wheel → scaling.
Right click to select model and move → whirling.
Shift + right click platform and move → move platform

Green: X axis

Yellow: Y axis

Place platform

Reset
Red: Z axis

46
Z axis mirroring

Y axis mirroring

X axis mirroring

47
Normal: Most used. Overhang: Used to see the vacant part.

Transparent

48
Layers:Used to simulate the effect of
each layer and the path.

Right click model → Left click “Multiply


object” → Example: copy 4 model

49
D. Printing Operation

1.Display Introduction

50
51
52
2.Filament Feeding
2.1 Set Preheat
Attention: Before filament installation, we need to preheat. Use PLA as example .

Press Knobs → Prepare → Preheat PAL → Start preheating

53
2.2 Filament Installation

54
2.3 Pull out filament

55
3.Platform Adjustment

56
57
4.Printing
1) SD Card Offline Printing

a. Loading mode

Cura supports STL file & G-code file.

58
b. Code Saving

Copy file to SD card . Then connect SD card to printer, click reset. Picture
below shows the location of print file , there are 2 methods to find print file.

c. Introduction of Stop print , Pause print , Continue Print:


Only when the printer is printing can we use Stop print, Pause print, Continue
Print.

59
d.Judgment of the gap between nozzle and platform.
1. Too big gap: The printed model is uneven, curled with gap. It means the gap is too big for
filament to reach the platform, making the printing effect so bad.

2. Too close gap: The printed model edge has irregular projections. It means the gap is too
close to print normally. Sometimes it even cannot output filament

3. Appropriate distance: Printed model flat with no gap, no glitches. It means the distance is
appropriate to print

Wait to print complete after gap adjustment.

60
2) USB Online Printing
a. Machine settings ( Use USB to connect to PC )

b. Online Pringting

61
E. FAQ

1. Z Axis Ajustment
During installation, we need to test moving parts:
1.

Preparation: Before Z axis moving adjustment, please confirm the height of


both Z aixs screw support is the same. ( Keep the same height of two white
parts )

62
2. Ajust concentricity

1. Click to adjust Z axis to move ( Position → Z pos.Fast → +/- ) . If it cannot move


smoothly, you need to adjust the unsmooth side’s screw support. Try to keep them at
the same height.
2. We can also tight/loose the Z motor screw according to requirments. This is to correct
the deviation in the first time installation. Please take steps as follows to lock screws,
position all screws first and finally tighten them all.

Z axis left screw support Z axis right screw support

63
Z motor & Flexible bearing Z motor screw locking sequence

1. Nozzle blocking

Tips: We have removed fan to show obviously. Please cosider movement according
to actual requirment.

A. Only a little filament left in the nozzle and difficult to take out:

64
65
B. Filament full filled in spout

66
3.FAQ
No. Symptom Reason Method
Synchronous wheel/belt Tighten set screws or
1 Print model dislocation
loose. fasten belt
Extruder temp is too high
Too high temp or slicing
2 Glitch with the print model and retracting speed &
problem.
distanse is too small
Rise extruder temp or
check if brass nut and
Low temp or not smooth
3 Foamy print model bearing is good. Replace a
filament entering.
nozzle if methods above
can’t solve the problem.
Hotbed level isn’t well
4 Printer model is warped Adjust hotbed
adjusted.
Unavaliable G-code
Wrong setting/wrong save Choose right machine type
5 tramsformation
path and change the right path

6 Software installation failed Different OS Reset OS


7 Unusual temp Broken temp sensor Change a new one

67
Ⅵ. Maintenance

Important maintenance tips:

1. maintenance of X,Y,Z axis: Add some lubricants on the rods to reduce friction when the

machine works noisy and a little bit shake.

2. Please refer to the USER MANUAL before printing, do preparation of hot bed

adjustment first.

3. When finished printing, the filament should keep sealing, avoid moisture.

4. Preheat the extruder at the beginning of 2 nd time printing, let extruder auto-push

filament for a while.

5. Machine should do some regular maintenance, drop some lubricating oil on thread rod,

polished rod and bearings to avoid fatigue wear.

6. Do not let the fan and air-condition blow to the hot bed when printing.

7. Keep the working condition at “Temp:10-30℃,Humidity:20-70%”.

68
Ⅶ. Maintenance Service Provision

1. This product executes regulations of “Product Warranty Card”.

2. Please contact supplier or customer service if the product have

any problems . Do not repair it by yourself, otherwise you need

to bear all the consequences.

69

You might also like