1

Date:19.09.2013/08.01.2014
Date:19.09.2013

TECHNICAL SPECIFICATIONS FOR 33 KV XLPE INSULATED

UNDERGROUND CABLES
1. SCOPE:

1.1 The scope of this specification covers the design, manufacture, stage inspection at works,
inspection and testing the finished ISI marked 33KV 3x400 Sq.mm stranded, compact circular
aluminum conductor, conductor screened with extruded semiconducting compound water tree
retardant (TR), XLPE insulated , insulation screened with extruded semi conducting
compound dry cured(Nitrogen gas cooled) from triple extrusion through common triple cross
head (single point triple extrusion) in combination with copper tape cores laid up, Filler inner
sheathed, galvanized round steel wire armored and overall PVC sheathed Black colour cable
conforming to IS:7098 /II/85 with latest amendments and as per specification detailed.

2. RATED VOLTAGE:
a. The rated voltage of the cable shall be 33000 Volts AC with the highest system
voltage of 36000 Volts between phases of the effectively earthed three-phase
transmission system.

3. APPLICABLE STANDARDS:
a. Unless otherwise stipulated in the specifications, the latest version of the following
Standards shall be applicable:
a. IS 7098 (Part 2)-Cross-linked Polyethylene insulation for Cables.
b. IS 8130-Conductors for insulated electrical cables and flexible cords.
c. IS 10810(series)-Methods of tests for cables.
d. IS 10418-Drums for electric cables.
e. IS 3975-Specification for mild steel wires, strips and tapes for armouring of cables.
f. IS 5831-Specification for PVC insulation sheath for electric cables.
g. IS 10462-Fictitious calculation method for determination of dimensions of protective
coverings of cables Part 1 - Elastomeric and thermoplastic insulated cables.

The cables manufactured to any other International Standards like BSS, IEC or equivalent
standards not less stringent than Indian Standards are also acceptable. In such cases the Bidders
shall enclose a copy of the equivalent international standard, in English language, along with the
bid.
 2

4. CONSTRUCTION:

4.1 Conductor: - The cable conductor shall be made from stranded aluminum to form compact
shaped conductor having resistance within the limits specified in IS:8130/1984 and any
amendment thereof. The wires shall be laid up together with a suitable right hand lay.
Stranded Class 2 – Annealed as per the IS:8130 / IEC 60228/ BS 6360 standards.

• The continuous rated current in ground shall be 410 A and 485 A in air.
• The Approx. conductor diameter shall ne 24.0 mm
• The Approx. DC resistance of conductor at 20 degrees centigrade shall be 0.0778 ohms.
• The Approx. AC resistance of conductor at 90 degrees centigrade shall be 0.101ohms.
• The Approx. Capacitance of the cable shall be 0.24 microfarads/KM.

4.2 Conductor Shield : The conductor having a non-magnetic semi-conducting screen shall
ensure perfectly smooth profile and avoid stress concentration. This conductor screen shall
be extruded in the same operation as the insulation, the semi-conducting polymer shall be
cross linked and shall be as per the IS:7098 Part 2, IEC:60502 Part – 2, BS:6622, BS:7835.

4.3 Insulation: - The insulation shall be water tree retardant (TR) cross linked polyethylene
insulation applied by extrusion and shall conform to the following requirements:

Sl.No. Properties Requirements

1. Tensile Strength 12.5N/mm², Min.
2. Elongation to break 200 percent, Min
3. Aging in air oven:
a) Treatment: Temperature: 135±3°C
Duration: 7 days
b) Tensile Strength variation: ±25 percent, Max
c) Elongation variation: ±25 percent, Max
4. Hot set:
a) Treatment: Temperature: 200±3°C
Time under load 15 min
Mechanical stress 20N/cm²
b) Elongation under load 175 percent, Max
c) Permanent elongation (set) after 15 percent, Max
cooling
5. Shrinkage:
a) Treatment: Temperature 130±3°C
Duration 1 hour
b) Shrinkage 4 percent, Max
6. Water absorption (Gravimetric):
a) Treatment: Temperature: 85±2°C
 3

Duration 14 days
b) Water absorbed 1 mg/cm², Max
7. Volume Resistivity
a) at 27°C 1x1014 ohm-cm, Min
b) at 70°C 1x1013 ohm-cm, Min
8 Thermal Resistivity 350 degrees C cm/W

9 Power factor at maximum conductor 0.008

temperature
10 Dielectric strength 22 kV/mm
4.3.1 The XLPE insulation should be suitable for specified 33 KV system voltage.
4.3.2 The curing process of XLPE insulation should be dry cured with nitrogen cooled.
4.3.3 The manufacturing process shall ensure that insulations shall be free from voids.
4.3.4 The insulation shall withstand mechanical and thermal stresses under steady state and
transient operating conditions.
4.3.5 The extrusion method should give very smooth interface between semi-conducting screen
and insulation.
4.3.6 The insulation of the cable shall be high stranded quality, specified in IS:7098 (Part-
II/1985). Withstand continuous conductor temperature of 90 deg C, which means higher
continuous rated current carrying
4.3.7 Capacity: The cables can operate even at conductor temperature of 130 deg C during a
short time emergency can withstand conductor temperature up to 250 deg C during a
Short Circuit condition
4.3.8 The average thickness of the insulation shall not be less than 8.8-mm. The insulation shall
be so applied that it fits closely on the conductor (or conductor screening or barrier if
any) and it shall be possible to remove it without damaging the conductor.

4.3.9 The eccentricity of the insulation thickness shall be less than 10% and ovality shall be
less than 5%.

4.4 Insulation Shield: To confine electrical field to the insulation, non-magnetic semi-
conducting shield shall be put over the insulation. The insulation shield shall be extruded in
the same operation as the conductor shield and the insulation by triple extrusion through
single head process and shall be as IS:7098 Part 2, IEC:60502 Part – 2, BS:6622, BS:7835.

4.5 Sheath : The sheath shall be suitable to withstand the site conditions and the desired
temperature. It should be of adequate thickness, consistent quality and free from all defects.
The PVC sheath shall be extruded as per IS:7098 Part-II/1985. IEC:60502 Part – 2,BS:6622,
LSOH to BS:7835.
 4

4.6 ARMOUR : Armoring shall be applied over the inner sheath with single galvanized steel
strip complying with the requirements of IS:3975/1979. The dimensions of the galvanized
wire shall be as specified in table 4 of the IS:7098/Part-II/1985. The armour wire shall be
applied as closely as practicable. The direction of the lay of the armour shall be left hand.
The joints in armour wire shall be made by brazing or welding and the surface irregularities
shall be removed. A joint in any wire shall be atleast 300mm from the nearest joint in any
other armour wire in the complete cable and shall be as per IS:7098 Part 2, IS: 3975,
IEC:60502 Part – 2, BS:6622, BS:7835

4.7 OUTER SHEATH : Extruded PVC ST2, outer sheath as per IS:5831/1984, IS:7098

Part 2, IEC:60502 Part – 2, BS:6622, LSOH to BS:7835. shall be applied over armoring
with suitable additives to prevent attack by rodents and termites. Outer sheathing shall be
designed to offer high degree of mechanical protection and shall also be heat, oils, chemicals,
abrasion and weather resistant. Common acids, alkalis, saline solutions etc., shall not have
adverse effects on the PVC sheathing material used.

4.8 The screening shall consist of nonmetallic semi-conducting compound, shielded cores

laid up with solid Non-hygroscopic fillers, inner sheath of extruded PVC, Galvanized round
wire Armour and PVC overall sheath.

4.9 The cables should be suitable for use in solidly earthed system.

4.10 The 33 kV underground cables shall be manufactured to the highest quality, best
workmanship with scientific material management and quality control. The bidder shall
furnish the quality plan, giving in detail the quality control procedure / management
system.

4.11 The cable shall be suitable for laying in covered trenches and/or buried underground to
meet the outdoor application purposes.

4.12 The successful Bidder shall give sufficient advance notice to the purchaser of not less
than one month to arrange for inspection and quality assurance program during
manufacture, at the works.

5 SYSTEM DETAILS:
General Technical particulars
 5

Nominal system voltage (rms) (U) 33KV

Highest system voltage (rms) (Um) 36.3KV
Phase to Earth voltage (rms) (Uo) 19.05 KV
Number of Phase 3
Frequency 50Hz
Variation in Frequency ± 3%
Type of Earthing Solidly Earthed
Basic impulse insulation level (1.2/50 µS wave) 170 kV
Total relay & circuit breaker Operating time 15 – 20 cycles

6 CLIMATIC CONDITIONS:
(a) Maximum ambient air temperature (in shade) 450 C
(b) Maximum ambient air temperature (under sun) 500 C
(c) Maximum daily average ambient air temperature 350 C
(d) Maximum yearly average ambient air temperature 300 C
(e) Maximum humidity 100%
(f) Altitude above M.S.L. Up to 1000M
(g) Average No. of thunder storm days per annum 50
(h) Average No. of dust storm days per annum Occasional
(i) Average No. of rainy days / annum 90
(j) Average Annual Rain fall 925mm
(k) Normal tropical monsoon period 4 months
(l) Maximum wind pressure 150 kg/Sq.M
7 DESIGN CRITERIA:

7.1 The cables that are covered in these specifications are intended for use outdoor , under
the climatic conditions and installation conditions described in the technical specification.

7.2 Any technical feature, not specifically mentioned here, but is necessary, for the good
performance of the product, shall be incorporated in the design. Such features shall be
clearly brought out under Technical deviations schedule only, in the offer made by the
bidder, giving technical reasons, and justifying the need to incorporate these features.

7.3 For continuous operation of the cables, at specified rating, the maximum conductor
temperature shall be limited to the permissible value as per the relevant standard,
generally not exceeding 90°C under normal operation and 250°C under short – circuit
conditions.

7.4 The cables in service will be subject to daily load cycles, of two peaks during a day;
morning peak and evening peak, with around 25% to 50% loading during the nights.

7.5 The materials used for outer sheaths shall be resistant to oils, acids and alkalis.

7.6 The cables shall have the mechanical strength required, during handling and laying.
 6

7.7 The cables shall be designed to withstand the thermo-mechanical forces and electrical
stresses during normal operation and transient conditions.

7.8 The cables shall be designed to have a minimum useful life span of Thirty-five years.

7.9 The detailed design drawings shall be submitted along with the bid documents.

8 MANUFACTURE PROCESS:

8.1.Cross-linking of the insulation materials water tree retardant (TR) (pre compounded
polyethylene) shall be conforming to IS: 7098 (Part – II) and the proof of purchase of the
above insulating material shall be submitted and is to be offered for stage inspection.

8.2 The conductor screen shall be of extruded semi conducting compound. The insulation
screen shall consist of the nonmetallic part, extruded semi conducting compound with non-
magnetic metallic part. The XLPE insulation and the shields for conductor and insulation
shall be extruded in one operation.

8.3 The cable must have Dry Cure-Dry (Nitrogen) Cooled Insulated Cores.

8.4 The cable must have Insulated Cores produced from triple Extrusion through Common
Triple Cross Head (single point triple extrusion).
8.5 The bidder shall specify the length of curing and cooling chamber.
8.6 The partial discharge shall be less than 2 PC and the bidder shall submit the type test
certificate with the value of less than 2 PC.
9 MATERIALS:

9.1 The conductor shall be of stranded construction. The material for conductor shall consist of
the plain aluminum of H2 or H4 grade as per clause – 3 of IS 8130/ 1984.

9.2 The minimum number of wires shall be 53 for circular compacted 400 sq. mm aluminum
conductor as per table – 2 of IS 8130/ 1984.

10 SCREENING:

10.1 The conductor screening shall be provided over the conductor by applying by extrusion of
semi-conducting compound. The semi-conducting compound shall withstand the operating
temperature of the cable and shall be compatible with the insulating material.
 7

10.2 The insulation screen shall be applied over the insulation. The insulation screening shall
consist of two parts; namely metallic and non-metallic. The non-metallic part shall be
applied directly over the insulation of each core and shall consist of a semi conducting tape
and extruded semi conducting compound with a semi conducting coating. The metallic part
of the insulation screen shall consist of either tape, or braid, or concentric serving of wires
or a sheath; shall be non-magnetic and shall be applied over the non-metallic part.

11 CORE IDENTIFICATION:

11.1 The core identification for 3 core cables shall be provided, by suitable means, like, by
application of colored stripes, or by numerals or by printing on the cores as per clause 13 of
IS: 7098 - Part 2
11.2 For identification of different coloring of XLPE Insulation, or by using colored strips, red,
yellow and blue colors respectively shall be used to identify the phase conductors.

12. LAYING UP OF CORES:

12.1 The cores shall be laid together with a suitable right hand lay. The interstices at the center
shall be filled with a non- hygroscopic material.

13. INNER SHEATH (COMMON COVERING):

13.1 The laid up cores shall be provided with inner sheath applied either by extrusion or by
wrapping. It shall be ensured that the shape is as circular as possible. The inner sheath shall
be so applied that it fits closely on the laid up cores and it shall be possible to remove it
without damage to the insulation.

13.2 The thickness of the inner sheath (common covering) shall be given as follows:

CALCULATED DIAMETER IN MM
OVER LAID UP CORES THICKNESS OF INNER
[REF IS 10462 (PART 1)] SHEATH (Min) mm
Over Up to and including
_ 25 0.3
25 35 0.4
35 45 0.5
45 55 0.6
55 _ 0.7

13.3 When one or more layers of binder tapes are applied over the laid up cores, the thickness of
such tapes shall not be construed as a part of inner sheath.
 8

14. ARMOURING:

14.1 Armoring shall be applied over the inner sheath with single galvanized steel strip complying
with the requirements of IS:3975/1979. The dimensions of the galvanized wire shall be as
specified in table 4 of the IS:7098/Part-II/1985. The armour wire shall be applied as
closely as practicable. The direction of the lay of the armour shall be left hand. The joints
in armour wire shall be made by brazing or welding and the surface irregularities shall be
removed. A joint in any wire shall be atleast 300mm from the nearest joint in any other
armour wire in the complete cable and shall be as per IS:7098 Part 2, IS: 3975, IEC:60502
Part – 2, BS:6622, BS:7835

14.2 Bidders shall furnish the calculation / data sheet for the short circuit carrying capability of
the Armour.
15. OUTER SHEATH:

15.1 The outer sheath shall be applied by extrusion. It shall be applied over the armouring shall
consist of poly-vinyl chloride (PVC) compound, conforming to the requirements of type
ST-2 of IS 5831. Suitable additives shall be added to give anti termite protection.

15.2 The minimum thickness of the PVC outer sheath shall not fall below the following value by
more than 0.2 mm + 0.2 ts

Calculated diameter under the outer sheath [IS

Nominal thickness of the
10462 Part 1] – mm
outer sheath (ts) - mm
Over Up to and including
_ 15 1.8
15 25 2.0
25 35 2.2
35 40 2.4
40 45 2.6
45 50 2.8
50 55 3.0
55 60 3.2
60 65 3.4
65 70 3.6
70 75 3.8
75 _ 4.0

16. IDENTIFICATION:

16.1 The outer sheath shall have the following information embossed or indented on it; the
manufacturer’s name or trade mark, the voltage grade, the year of manufacture and the
 9

letters “A_PDCL”. The identification shall repeat every 300/350 mm along the length of
the cable. Outer sheath of cable shall be black in permanent colour.

17. INSPECTION AND QUALITY CONTROL:

17.1 The Bidder shall furnish a complete and detailed quality plan for the manufacturing process
of the cable. All raw materials shall conform to relevant applicable standards and tested for
compliance to quality and requirement. During the manufacturing process, at all stages,
inspections shall be made to check the physical and dimensional parameters, for
verification to compliance to the standards. The bidder shall arrange, for inspection by the
purchaser, during manufacture with one month advance notice for verifying the various
stage inspections as specified in the quality assurance plan enclosed to verify the quality
control process of the Bidder.

18. TYPE TESTS:

Type test certificates from Accredited NABL Testing Laboratories for 33 kV XLPE UG
cable, shall be submitted along with Bid. The Type Tests should have been conducted not
later than 5 years as on the date of BID opening.

18.1 Stage wise Inspection

The Bidder shall offer the stage wise inspection as detailed in the in the quality assurance
plan

18.2 Notwithstanding, that type test have been conducted earlier, the supplier shall conduct all
type tests as per IS: 7098 part-II, 1985, with up to date amendments or equivalent
international standard, and supplies made only after approval of test reports from the
purchaser. The purchaser reserves the right to wave the repetition of the type test.

18.2 All acceptance tests shall be conducted in the presence of the purchaser/ representative.

18.3 The supplier shall give 15 days advance notice for inspections, and witnessing of tests by
the purchaser or his representative.

18.4 The following type tests shall be conducted on the cable.

Sl. Test method Ref.
Test Requirement
No. Part no of IS: 10810
Tests on conductor IS:8130 1
a) i) Tensile test IS:8130 2
ii) Wrapping test IS:8130 3
 10

iii) Resistance test

Clause 15.2 &
b) Tests for armoured wires and strips 5
IS:3975
Test for thickness of insulation and Clause 4.3, 14.2
c) 6
sheath & 16.2
Physical tests for insulation:
i) Tensile strength and 7
elongation at break
d) ii) Aging in air oven Clause 4.2 11
iii) Hot test 30
iv) Shrinkage test 12
v) Water absorption (gravimetric) 33
Physical tests for outer sheath
i) Tensile strength and elongation 7
at break
e) IS: 5831
ii) Aging in air oven 11
iii) Shrinkage test 12
iv) Hot deformation 15
Bleeding and blooming test
f) IS: 5831 19
(outer sheath)
g) Partial discharge test Less than 2 PC
h) Bending test 50
Dielectric power factor test
j) i) As a function of voltage 48
ii) As a function of temperature
Insulation resistance
k) Clause 4.2 43
(volume resistivity) test
m) Heating cycle test Clause 22.5 49
n) Impulse withstand test Clause 22.6 47
p) High voltage test Clause 22.7 45
q) Flammability test Clause 22.8 53
The following test shall be performed successively on the same test sample of completed cable,
not less than 10 M in length between the test accessories:
I.
Partial discharge test.
II.
Bending test followed by partial discharge test.
III.
Dielectric power factor as a function of voltage.
IV.
Dielectric power factor as a function of temperature.
V.
Heating cycle test followed by dielectric power factor as a function of voltage and
partial discharge tests.
VI. Impulse withstand test
VII. High voltage test.
19. ACCEPTANCE TEST:

19.1 The sampling plan for acceptance test shall be as per IS 7098 part -II, Appendix ‘A’.
 11

19.2 The following shall constitute the acceptance test.

a) Tensile test for aluminum.

b) Wrapping test for aluminum.
c) Conductor resistance test.
d) Test for thickness of insulation.
e) Test for thickness of inner and outer sheath.
f) Hot-set test for insulation.
g) Tensile strength and elongation at break test for insulation and outer sheath.
h) Partial discharge test (on full drum length).(shall be less than 2PC)
i) High voltage test.
j) Insulation resistance (volume resistivity) test.

20. ROUTINE TEST:

20.1 The following shall constitute routine tests:

a) Conductor resistance test.
b) Partial discharge test on full drum length.
c) High voltage test.

21. DETAILS OF TESTS:

21.1 Unless otherwise mentioned in this specification, the tests shall be carried out in accordance
with appropriate part of IS: 10810.

21.2 The partial discharge magnitude at test voltage equal to 1.5Uo shall not exceed 2 pC.

21.3 Bending test: The diameter of the test cylinder shall be 200±5% D; where D is the overall
diameter of the completed cable. After completing the bending operations, the test sample
shall be subjected to partial discharge measurement and shall comply with the requirements
given in 22.2.

21.4 Dielectric power factor test:

21.4.1 Tan δ as a function of voltage: The measured value of Tan δ at Uo shall not exceed 0.004
and the increment of Tan δ between 0.5 Uo and 2 Uo shall not be more than 0.002.

21.4.2 Tan δ as a function of Temperature: The measured value of Tan δ at Uo shall not exceed
0.004 at the ambient temperature and 0.008 at 90°C.

21.5 Heating cycle test: The sample, which has been subjected to previous tests, shall be laid out
on the floor of the test room and subjected to heating cycles. After the third cycle, the
 12

sample shall be subjected to dielectric power factor as a function of voltage, and partial
discharge test.
21.6 Impulse voltage withstand test: The impulse voltage level shall be 170 kV. No breakdown
of insulation shall occur during the test.

21.7 High Voltage Test:

21.7.1 Type test and Acceptance tests: The cable shall withstand without breakdown an ac
voltage equal to 3 Uo when applied to the sample between conductor and screen/armour.
The voltage shall be gradually increased to the specified value and maintained for a period
of 4 hours.
21.7.2 Routine test: The cable shall withstand without any failure, 48 kV rms between
conductors and screen/armour, when applied for a period of five minutes for each test
connection.

21.8 Flammability test: Period of burning after removal of the flame shall not exceed 60 seconds
and the unaffected (un charred) portion from the lower edge of the top clamp shall be at
least 50-mm.

AP-PDCL reserves the right to select a random sample of 33 kV UG cable from the
Manufacturer’s end which are ready to dispatch and also ongoing cable laying works and
the same samples will be sent to any testing laboratory as desired by AP-PDCL at Bidders
cost. If the testing results are found to be not satisfactory AP-PDCL reserves the right to
reject the entire batch of cable received and insists for replacement of material free of cost.
The decision of AP-PDCL in this regard is final.

22. PACKING:

22.1 The cables, as per specified delivery lengths, shall be securely wound /packed in non-
returnable steel drums, capable of withstanding rough handling during transport by Rail,
Road, etc. The packing should withstand storage conditions in open yards. The cable
drums shall conform to IS 10418-1982 or equivalent standard. The dimensional drawings of
steel drums shall be furnished with the bid. The drum shall be provided with
circumferential lagging of strong wooden planks. The end of the cable shall be sealed with
good quality heat shrink sealing caps. The sufficiently required additional sealing caps shall
be supplied for use of testing during laying and jointing at site and to seal spare lengths of
cable. The packing should be able to withstand the rigorous of transport. The following
information in bold letters in English shall be painted on the flanges.

i) Name & Address of the manufacturer, Trade name/Trade mark/Brand

ii) Size of cable (Cross section) rated voltage, standard, insulation, cable code, drum
No., and year of manufacture.
iii) Length of cables (Meters)
 13

iv) Direction of rolling

v) Net weight (in Kg)
vi) Gross weight (in Kg)
vii) Owners purchase order reference.
23. SEALING OF CABLE ENDS ON DRUMS:

23.1 The cable ends shall be sealed properly so that ingress of moisture is completely prevented.
The individual core endings shall be sealed effectively with water resistant compound
applied over the core and provided with a heat shrinkable or push-on or Tapex or cold
shrinkable type cap of sufficient length with adequate cushion space so that the conductor
does not puncture the cap in case of movement of the core during unwinding or laying.
Before sealing, the semi conducting layer on the cores may be removed for about 2 mm at
each end, to facilitate checking the insulation resistance from one end, without removing
the sealing cap at the other end.

23.2 The three cores should have an overall heat shrinkable or push-on or Tapex or cold
shrinkable type cap with adequate end clearance, and sufficient cushioning to prevent
puncturing of the overall sealing cap due to stretching of the cores. The sealing cap shall
have sufficient mechanical strength and shall prevent ingress of moisture into the cable.
The ends of single core cables shall also be sealed on the same lines to prevent entry of
moisture.
24. CABLE LENGTHS:

24.1 The cables shall be supplied in continuous lengths of 300 m or more with 5% tolerance and
cable shall on the steel drums only.

25. QUANTITY TOLERANCE:

A +3% tolerance shall be allowed on the ordered quantity including 300m cable as spare.

26. MARKING:

The packed cable drum shall carry the following information, clearly painted or stenciled.
a) The letters AP-PDCL
b) Reference to Standard and ISI mark.
c) Manufacturer’s Name or trade mark.
d) Type of cable & voltage grade.
e) Number of cores.
f) Nominal cross- sectional area of conductor.
g) Cable code.
h) Length of cable on the drum.
i) Direction of rotation.
j) Gross weight.
k) Country of Manufacture.
 14

l) Year of Manufacture.
m) Purchase order and date.
n) Address of consignee.

27. GUARANTEED TECHNICAL PARTICULARS:

The bidder, shall furnish the guaranteed technical particulars of the cable offered in the GTP
format provided
28 DRAWING & LITERATURE:

The following shall be furnished along with the tender

a) Cross sectional drawings of the cables, giving dimensional details.
b) An illustrated literature on the cable, giving technical information, on current ratings,
cable constants, short circuit ratings, derating factors for different types of installation,
packing date, weights and other relevant information.
29.GUARANTEE:
The cable manufactured shall be guaranteed for the period of 18 months from the date of
receipt at stores.

30.The tenderer shall furnish a copy of valid BIS licence for ISI marking together with their
offer, without which the offer shall be treated as non-responsive.
 15

A1 : GUARANTEED TECHNICAL PARTICULARS FOR 33 KV UG Cable

Bidder's Name
Class of Power Cable
1 Name of the Manufacturer and country of origin
2 Country of Manufacture
3 Type of cable / cable code
4 Applicable standard
Voltage
5 a. Rated Nominal voltage
b) Rated Maximum voltage
Suitability for :
6 a. Earthed system
b. Unearthed system
Conductor
a) Nominal cross section (sq.mm)
b) Material
7 c) Shape
d) Diameter of conductor (mm)
e) Number of wires per conductor (Nos.)
f) Nominal diameter of wire in conductor (mm)
Conductor screen
a) Material and type
8 b) Thickness (mm)
c) Maximum volume resistivity at 90 deg C before
and after ageing (ohm-cm)
Maximum value of Electric stress at
9 a) Conductor screen KV/mm
b) At the insulation KV/mm
Insulation XLPE
10 a) Curing process (furnish details separately)
b) Material/Composition
 16

c) Dia over insulation

d) Radial thickness
i. Nominal (mm)
ii. Average (mm)
iii. Minimum (mm)
Insulation screen (Non metallic)
a) Material
11 b) Nominal thickness (mm)
c) Maximum volume resistivity at 90 deg. C. (ohm-
cm)
Tape swellable (Longitudinal water / Moisture /
Protection)
12 a) Material
b) Thickness (mm)
c) Tolerance
sheath
a) Type / composition
b) Material
13
c) Nominal thickness
d) Tolerance on thickness
e) Diameter of cable over sheath (mm)
Bedding Tape over Inner sheath
i) Material
14 ii) Dimension (Wxt) (mm) x (mm)
Nom. (mm)
Min. (mm)
Concentric screen / Armour of wires
a) Material
15 b) Dia of wire
Nom. (mm)
Min. (mm)
Binder open Helix, contact copper Tape over screen /
Armour wires
a) Material
16
b) Dimension (Wxt)
Nom. (mm)
Min. (mm)
17 Non-woven water swellable Tape over Binder Tape
 17

a) Material
b) Dimension
Overall sheath
i) Material & Type
18 ii) Thickness
Nom. (mm)
Min. (mm)
Conductive coating outer sheath
19 a) Material
b) Thickness
Anti-termite treatment to outer sheath
20
a) Material
21 External overall dia of cable
Short circuit rating of conductor 90 deg. C operating
22
temperature for 1 Sec.
Minimum cable bending radius (in terms of cable
23
diameter)
24 Permissible maximum tension
Continuous current rating under specified insulation
conditions at conductor temperature of 65 deg. C and
90 deg. C.
Ground Temperature 30 deg. C
Thermal resistivity of soil 150 deg. C CM/W
25
Depth of laying 200 mm
Ambient Air temperature 40 deg. C
No. of circuits 1 OR 2
Spacing between two circuits (600 mm)
Formation
Maximum permissible conductor temperature for
26 continuous operation under specified installation
conditions (deg. C)
27 Conductor temperature at rated current (deg. C)
Basic impulse level at conductor temperature of 90
28
deg. C (KV)
29 Impulse wave shape
30 Power frequency with stand voltage (KV)
31 Tan Delta at 50 Hz (at U.KV and 90 (-5/+10) deg. C
 18

32 Sheath voltage at max. load

33 Withstand voltage of sheath on spark test
Permissible short circuit current ratings of conductor
i) 0.1 Sec KA
34
ii) o.2 Sec KA
iii) 0.5 Sec KA
iv) 1.0 Sec KA
Conductor resistance DC & AC
a) at 20 deg. C (d.c)/A.C. ohm/KM
35 b) at 90 deg. C (d.c)/A.C. ohm/KM
c) at 105 deg. C (d.c)/A.C. ohm/KM over load
temp) a.c. (ohm)

Equivalent star resistance at 50 Hz of 3 phase current

a) at 20 deg. C (d.c)/A.C. ohm/KM
36
b) at 90 deg. C (d.c)/A.C. ohm/KM
c) at 10% continuous overload temperature (ohm/KM)
37 Star reactance at 50 hz (ohm/KM)
Approximate impedance at 50 hz per KM
a) at 20 deg. C ohm/KM
38 b) at 90 deg. C ohm/KM
c) at 10% continuous overload temperature (ohm/KM)

Self electrostatic capacitance per phase (Micro

39
farad/KM)
Maximum power factor at charging KVA of cables
when laid direct in ground at normal voltage &
40 frequency
a) at ambient Temperature
b) at Maximum conductor Temperature
a) Positive and negative sequence impedance
41 (ohm/KM)
b) Zero sequence impedance (ohm/KM)
Zero sequence data
42 a) Series resistance (ohm/KM)
b) Series reactance (ohm/KM)
 19

c) Shunt capacitive reactance (ohm/KM)

a) Sheath resistance at 20 deg. C ohm/KM
43 b) Screen resistance at 20 deg. C ohm/KM
c) Combined resistance at 20 deg. C ohm/KM
44 Surge impedance of cable (ohm/KM)
45 IR value at ambient temperature per KM
Maximum magnitude of partial discharge at 1.5 U.o
46 At Ambient Temperature (Po)
At High Temperature (Po)
47 Losses per Km.
NOTE : (i) Cable Conductor size 400 sq. mm
a) Total 3 phase dielectric loss
i. One circuit alive Kw/KM
ii. Both circuits alive KW/KM on each circuit
b) Total 3 phase resistive loss
i. One circuit alive Kw/KM
ii. Both circuits alive KW/KM on each circuit
c) Total 3 phase sheath / screen loss
i. One circuit alive Kw/KM
ii. Both circuits alive load KW/KM on each circuit
d) Other losses due to reinforcement
i. One circuit alive KW/KM
ii. Both circuits alive KW/KM on each circuit
e) Total losses
i. One circuit alive KW/KM
ii. Both circuits alive KW/KM
48 Charging current at rated voltage per Km (Amps)
Short circuit capacity of conductor for one second at
49 90 deg. C prior to short circuit and 250 deg. C during
short circuit (KA)
50 Circulating current under the BEB condition in
i. sheath Amps
ii. Copper tape screen Amps
iii. In both Amps
when current in conductor is the rated current
Circulating current in sheath armouring /Cu screen
51 (when the conductor is carrying 25 KA S.C. current.
In KA
 20

Combined short circuit capacity of Metallic sheath and

screen for 1 Sec. at metallic sheath/screen temperature
52
of 75 deg. C (conductor temperature 90 deg. C before
S.C and 250 deg. C during S.C
Screening factor of cable for calculating interferance
53
on control and communication cables :
Approximate value of attenuation of carrier current
signals operating over a frequency range
i. 50 KC/s - dB/KM
54
ii. 100 KC/s - dB/KM
iii. 150 KC/s - dB/KM
iv. 200 KC/s - dB/KM
Shipping weight and size of cale drum
a) Size of Drum
i. Dia of Drum (M)
55 ii. Width of Drum (M)
iii. Gross Weight (Kgs)
iv. Length of cable per Drum (M)
v. Weight of Cable (Kg/M)
 21

DERATING FACTORS

1 VARIATION IN GROUND TEMPERATURE :

Ground Temperature (deg. C) : 15 20 25 30 35 40 45
Rating Factor
2 VARIATION IN DEPTH OF LAYING :
Depth of Laying (Meters): 0.7 0.9 1.0 1.2 1.3 1.5
Rating Factor

3 VARIATION IN THERMAL RESISTIVITY OF SOIL

Thermal Resistivity of Soil : (deg. C cm/watt) 100 120 150.0 200 250
Rating Factor

4 VARIATION IN AIR TEMPERATURE :

Air Temperature (deg. C) : 25 30 35 40 45 50 55
Rating Factor

5 VARIATION DISTANCE (MM) :

Axial Distance (mm) Between circuits : 100 200 300.0 400 600 800
Rating Factor
 22

Current Rating Factor

Single Point Bonded Both End Bonded

Particulars 65 deg. 90 deg. 65 deg. 90 deg.
C Amps C Amps C Amps C Amps
Current Rating conductor size 400 Sq. mm
a) In Ground
i. Of each circuits (when both the circuits alive)
ii. Of one circuits (when other circuit is isolated)
b) In Duct
i. Of each circuits (when both the circuits alive)
ii. Of one circuits (when other circuit is isolated)
c) In pipe, one cable per pipe.
i. Of each circuits (when both the circuits alive)
ii. Of one circuits (when other circuit is isolated)
d) In Air
i. Of each circuits (when both the circuits alive)
ii. Of one circuits (when other circuit is isolated)