TECHNOLOGICAL INSTITUTE OF THE PHILIPPINES – MANILA

COLLEGE OF ENGINEERING AND ARCHITECTURE

INTEGRATION COURSE 3 FOR CE

PLATE NO.2
REINFORCED CONCRETE DESIGN

m
er as
co
eH w
o.
rs e
ou urc
RATING
o
aC s
v i y re

SUBMITTED BY:
ed d

1520113 AUTOR, JOY LAURIA MAE B.

SECTION
CE52S1
sh is
Th

SUBMITTED TO:
ENGR. JOEVANNIE EMMANUEL C. LUMAGAS

DATE SUBMITTED
December 18, 2020

This study source was downloaded by 100000831588742 from CourseHero.com on 09-21-2021 20:31:27 GMT -05:00

https://www.coursehero.com/file/77434304/plate-no2-autor-joydocx/
 Problem no. 1

The figure shows a floor plan which is deign to carry a live load of 4.8 kPa and a dead load of 4.9 kPa (including
weight of slab, beam, ceiling, partition, floor, etc.). The slab thickness is 100 mm. The beam has a width of 250 mm
and has a depth of 350 mm below the slab. The girder has a width of 350 mm and a depth of 400 mm. Use 70 mm
covering from center of steel reinforcements using normal weight concrete. Use fc’ = 20.7 MPa, fy = 415 MPa, fyt =
275 MPa. Use NSCP 2010.

a. Assuming the beam to be simply supported, determine the critical factored shear force at the critical section
for beam BE.

b. Determine the spacing for the two legs of 10 mm Ø

c. Using the NSCP code provisions, determine the maximum spacing of stirrups.

m
er as
co
eH w
o.
rs e
ou urc
o
aC s
v i y re
ed d
ar stu
sh is
Th

This study source was downloaded by 100000831588742 from CourseHero.com on 09-21-2021 20:31:27 GMT -05:00

https://www.coursehero.com/file/77434304/plate-no2-autor-joydocx/
 SOLUTION

m
er as
co
eH w
o.
rs e
ou urc
o
aC s
v i y re
ed d
ar stu
sh is
Th

This study source was downloaded by 100000831588742 from CourseHero.com on 09-21-2021 20:31:27 GMT -05:00

https://www.coursehero.com/file/77434304/plate-no2-autor-joydocx/
 Problem no. 2
Girder AB is subjected to torsional moment in addition to the flexural moment and shear from the heavy loads at
the cantilever frames. From analysis, the following factored design result: Mu = 440 kN-m, Vu = 280 kN, Tu = 180 kN-
m, width of beam, “b” = 400 mm, total depth of beam, “h” = 500 mm, fc’ =20.7 MPa, fyt = 275 MPa, fy = 415 MPa,
concrete cover to centroid of tension steel = 65 mm, steel ratio at balanced condition = 0.02, allowable concrete shear
stress = 0.76 MPa, lateral ties are 12 mm diameter.

a. Which of the following gives the tension reinforcement required for factored moment, Mu.

b. Which of the following gives the spacing of transverse reinforcement for factored shear, Vu.

c. Which of the following gives the longitudinal reinforcement required for torsion, Tu. Assume 40 mm clear cover to
lateral ties.

m
er as
co
eH w
o.
rs e
ou urc
o
aC s
v i y re
ed d
ar stu
sh is
Th

This study source was downloaded by 100000831588742 from CourseHero.com on 09-21-2021 20:31:27 GMT -05:00

https://www.coursehero.com/file/77434304/plate-no2-autor-joydocx/
 SOLUTION

m
er as
co
eH w
o.
rs e
ou urc
o
aC s
v i y re
ed d
ar stu
sh is
Th

This study source was downloaded by 100000831588742 from CourseHero.com on 09-21-2021 20:31:27 GMT -05:00

https://www.coursehero.com/file/77434304/plate-no2-autor-joydocx/
 Problem no. 3
A tied column 350 mm x 600 mm is reinforced with 2 – 28 mm Ø at the left side and 2 – 34 mm Ø in the right
side. Use fc’ = 27.6 MPa, fy = 415 MPa.

a. Compute the total axial capacity of the column, considering area of displaced by concrete compression bars.

b. Compute the plastic centroid measured from center to column.

c. Compute the spacing of the 10 mm ties.

m
er as
co
eH w
o.
rs e
ou urc
o
aC s
v i y re
ed d
ar stu
sh is
Th

This study source was downloaded by 100000831588742 from CourseHero.com on 09-21-2021 20:31:27 GMT -05:00

https://www.coursehero.com/file/77434304/plate-no2-autor-joydocx/
 SOLUTION

m
er as
co
eH w
o.
rs e
ou urc
o
aC s
v i y re
ed d
ar stu
sh is
Th

This study source was downloaded by 100000831588742 from CourseHero.com on 09-21-2021 20:31:27 GMT -05:00

https://www.coursehero.com/file/77434304/plate-no2-autor-joydocx/
 Problem no. 4
A short rectangular, reinforced concrete column is 300 mm x 375 mm as shown in the figure. It is reinforced with
6 – 28 mm Ø bars, fc’ = 27.6 MPa, fy = 414 MPa. Neglect the area of concrete displaced by the compression steel bar.

a. Determine the balanced load.

b. Determine the balanced moment.

c. Determine the nominal load Pn if it is acting at an eccentricity of 300 mm.

m
er as
co
eH w
o.
rs e
ou urc
o
aC s
v i y re
ed d
ar stu
sh is
Th

This study source was downloaded by 100000831588742 from CourseHero.com on 09-21-2021 20:31:27 GMT -05:00

https://www.coursehero.com/file/77434304/plate-no2-autor-joydocx/
 SOLUTION

m
er as
co
eH w
o.
rs e
ou urc
o
aC s
v i y re
ed d
ar stu
sh is
Th

This study source was downloaded by 100000831588742 from CourseHero.com on 09-21-2021 20:31:27 GMT -05:00

https://www.coursehero.com/file/77434304/plate-no2-autor-joydocx/
Powered by TCPDF (www.tcpdf.org)