C031_SystemError(Fxxx)Outline 1/8

No. Content Check procedure & check point Remark 1 Remark 2

1) Check connection of the harness (Panel to Main board), (Main board to HDD)
and connectors and check function.
2) Check contact of the DDR memory by detaching and reattaching. and check [Main - Panel Interface]
Lock-up at Welcome display function. replace it if available and check function. *User data and installed Main bord:YC12, YC1,YC30
(The display unchages after 3) Format the HDD and check function. (U024 FULL formatting) software is deleted if Panel board:YC1,YC2,YC3
-
3 minutes 30 seconds or 4) Execute the U021Memory initializing to initialize the controller backup memory executing the U024.
more) and check function. Reinstallation is required. [Main - HDD]
5) Replace the panel board and check function. Main board:YC1,YC2
6) Replace the main board and check function.
7) Retrieve the USBLOG and contact the Service Administrative Division.
[Main-Panel Interface]
1) Check connection of the harness (Panel to Main board), (Main board to HDD)
Mainboard: YC12,YC17,YC30
and connectors and check function.
Panel borad: YC1,YC2,YC3
CF000 appears in 3minutes 2) Check contact of the DDR memory by detaching and reattaching. and check
30 seconds after the function. replace it if available and check function.
If the LEDs are in the state
Welcome display continues 3) Format the HDD and check function. (U024 FULL formatting)
F000 belwo when the F000 appears,
4) Execute the U021 Memory initializing to initialize the controller backup memory
the DDR2 memory failure may
Panel－Main board and check function.
be the cause. Check contact of
communication error 5) Replace the main board and check function.
theYS1 or YS2 with the
6) Replace the Panel board and check function.
memory.
7) Retrieve the USBLOG and contact the Service Administrative Division.
Memory LED turned on
1) Format the HDD and check function. (U024 FULL formatting)
F10X 2) Execute the U021 Memory initializing to initialize the controller backup memory
An error is detected at OS or and check function.
some of device drivers. 3) Replace the main board and check function.
F11X 4) Replace the HDD and check function.
5) Retrieve the USBLOG and contact the Service Administrative Division.
[Main-Scan Interface]
Main board:YC11,YC25
1) Check connection of the harness (Scan/DP - Main board) and connectors and
ISC board:
check function.
2) Format the HDD and check function. (U024 FULL formatting)
[Main-DP relay
An error is detected at the 3) Execute the U021 Memory initializing to initialize the controller backup memory
F12X Interface]　(Check if the boards
Scan control section and check function.
are firmly connected via the
4) Replace the Scan/DP board and check function.
board-to-board connector.)
5) Replace the main board and check function.
Main board:YC10
6) Retrieve the USBLOG and contact the Service Administrative Division.
DP relay board:YC4

1) Check connection of the harness (Panel - Main board) and connectors and
check function.
2) Format the HDD and check function. (U024 FULL formatting)
[Main-Panel Interface]
An error is detected at the 3) Execute the U021 Memory initializing to initialize the controller backup memory
F13X Main board:YC12,YC17,YC30
Panel control section and check function.
Panel board:YC1,YC2,YC3
4) Replace the panel board and check function.
5) Replace the main board and check function.
6) Retrieve the USBLOG and contact the Service Administrative Division.
 C031_SystemError(Fxxx)Outline 2/8
No. Content Check procedure & check point Remark 1 Remark 2
1) Check connection of the harness (FAX - Main board) and connectors and
check function.
2) Format the HDD and check function. (U024 FULL formatting)
F14A,F14F: KUIO error
3) Execute the U021 Memory initializing to initialize the controller backup memory
Main board (USB hub)
and check function.
An error is detected at the
F14X 4) Execute the U671 Clear FAX back up data (FAX DIMM clear) and check
FAX control section [Main-KUIO Interface]
function. (Take cae of the received data since it is cleared)
Main board:YC8,YC9
5) Replace the FAX_DIMM and check function.
KUIO board:YC3,YC4
6) Replace the FAX board and check function.
7) Replace the main board and check function.
8) Retrieve the USBLOG and contact the Service Administrative Division.
1) Check connection of the harness (Authentication device - Main board) and
connectors and check function.
2) Format the HDD and check function. (U024 FULL formatting)
An error is detected at the
3) Execute the U021 Memory initializing to initialize the controller backup memory Authentication device: Card
F15X authentication device control
and check function. Reader, etc.
section
4) Replace the main board and check function.
5) Replace the HDD and check function.
6) Retrieve the USBLOG and contact the Service Administrative Division.

1) Format the HDD and check function. (U024 FULL formatting)

2) Execute the U021 Memory initializing to initialize the controller backup memory
An error is detected at the and check function.
F17X
print data control section 3) Replace the main board and check function.
4) Replace the HDD and check function.
5) Retrieve the USBLOG and contact the Service Administrative Division.

1) Check connection of the harness (Engine - Main board) and connectors and
check function.
2) Format the HDD and check function. (U024 FULL formatting) [Main⇔ENGINE Interface]
An error is detected at the 3) Execute the U021 Memory initializing to initialize the controller backup memory Main board:YC3
F18X
Video control secion and check function. Engine
4) Replace the engine board and check function. board:YC46　or　YC50
5) Replace the main board and check function.
6) Retrieve the USBLOG and contact the Service Administrative Division.
 C031_SystemError(Fxxx)Outline 3/8
No. Content Check procedure & check point Remark 1 Remark 2
1) Format the HDD and check function. (U024 FULL formatting)
F19X 2) Execute the U021 Memory initializing to initialize the controller backup memory
An error is detected at the and check function.
OS or some of device drivers 3) Replace the main board and check function.
F1AX 4) Replace the HDD and check function.
5) Retrieve the USBLOG and contact the Service Administrative Division.
1) Format the HDD and check function. (U024 FULL formatting)
2) Execute the U021 Memory initializing to initialize the controller backup memory
An error is detected at the
and check function.
F1BX Security management
3) Replace the main board and check function.
section
4) Replace the HDD and check function.
5) Retrieve the USBLOG and contact the Service Administrative Division.
1) Format the HDD and check function. (U024 FULL formatting)
2) Execute the U021 Memory initializing to initialize the controller backup memory
An error is detected at the *The F1C4 error appears
and check function.
F1CX File System management with the HDD security kit at
3) Replace the main board and check function.
section work.
4) Replace the HDD and check function.
5) Retrieve the USBLOG and contact the Service Administrative Division.
1) Format the HDD and check function. (U024 FULL formatting)
*The F1D4 error is RAM
2) Execute the U021 Memory initializing to initialize the controller backup memory
An error is detected at the allocation error.
and check function.
F1DX Image memory management 　1Check it with the U340
3) Replace the main board and check function.
section 　2Initialize the setting
4) Replace the HDD and check function.
valued with the U021
5) Retrieve the USBLOG and contact the Service Administrative Division.
1) Format the HDD and check function. (U024 FULL formatting)
F1EX
2) Execute the U021 Memory initializing to initialize the controller backup memory
An error is detected at the and check function.
F1FX
OS or some of device drivers 3) Replace the main board and check function.
4) Replace the HDD and check function.
F20X 5) Retrieve the USBLOG and contact the Service Administrative Division.
F21X [DDR2 memory contact check]
1) Check contact of the DDR memory and check function.
Main board:YS1 or YS2
2) Format the HDD and check function. (U024 FULL formatting)
A certain part of the memory be
F22X 3) Execute the U021 Memory initializing to initialize the controller backup memory
An error is detected at the faulty. The frequency of faiure
and check function.
Image processing section occurrence is dependent on
4) Replace the main board and check function.
the frequency of access to the
F23X 5) Replace the HDD and check function.
faulty bit. The ASIC may be
6) Retrieve the USBLOG and contact the Service Administrative Division.
faulty if the memory is not
 C031_SystemError(Fxxx)Outline 4/8
No. Content Check procedure & check point Remark 1 Remark 2
[DDR2 memory contact check]
1) Check contact of the DDR memory and check function. Main board:YS1 or YS2
2) Format the HDD and check function. (U024 FULL formatting) *The F248 eror is printer A certain part of the memory be
3) Execute the U021 Memory initializing to initialize the controller backup memory process error. if it repeats faulty. The frequency of failure
An error is detected at the
F24X and check function. with a certain print data, occurrence is dependent on
System management section
4) Replace the main board and check function. retrieve the capture data the frequency of access to the
5) Replace the HDD and check function. and USBLOG. faulty bit. The ASIC may be
6) Retrieve the USBLOG and contact the Service Administrative Division. faulty if the memory is not
sensitive.
1) Format the HDD and check function. (U024 FULL formatting)
2) Execute the U021 Memory initializing to initialize the controller backup memory
An error is detected at the
and check function. *This may be owing to the
F25X Network management
3) Replace the main board and check function. users network environment.
section
4) Retrieve the USBLOG and contact the Service Administratuve Division.
(or retrieve the packet capture data depending on the reult of analysis)
F26X 1) Format the HDD and check function. (U024 FULL formatting)
F27X 2) Execute the U021 Memory initializing to initialize the controller backup memory
An error is detected at the and check function.
F28X
System management section 3) Replace the main board and check function.
F29X 4) Replace the HDD and check function.
F2AX 5) Retrieve the USBLOG and contact the Service Administrative Division.
F2BX
F2CX 1) Format the HDD and check function. (U024 FULL formatting)
F2DX 2) Execute the U021 Memory initializing to initialize the controller backup memory
F2EX An error is detected at the and check function.
F2FX Network control section 3) Replace the main board and check function.
F30X 4) Retrieve the USBLOG and contact the Service Administratuve Division.
F31X (or retrieve the packet capture data depending on the reult of analysis)
F32X
1) Check connection of the harness (Scan/DP board - main board) and
connectors and check function.
2) Format the HDD and check function. (U024 FULL formatting)
An error is detected at the 3) Execute the U021 Memory initializing to initialize the controller backup memory
F33X
Scan management section and check function.
4) Replace the Scan/DP board and check function.
5) Replace the main board and check function.
6) Retrieve the USBLOG and contact the Service Administrative Division.
1) Check connection of the harness (Panel board - main board) and connectors
and check function.
2) Format the HDD and check function. (U024 FULL formatting)
An error is detected at the 3) Execute the U021 Memory initializing to initialize the controller backup memory
F34X
Panel management section and check function.
4) Replace the panel board and check function
5) Replace the main board and check function.
6) Retrieve the USBLOG and contact the Service Administrative Division.
 C031_SystemError(Fxxx)Outline 5/8
No. Content Check procedure & check point Remark 1 Remark 2
1) Format the HDD and check function. (U024 FULL formatting)
2) Execute the U021 Memory initializing to initialize the controller backup memory
An error is detected at the and check function.
F35X
Print control section 3) Replace the main board and check function.
4) Replace the HDD and check function.
5) Retrieve the USBLOG and contact the Service Administrative Division.
1) Format the HDD and check function. (U024 FULL formatting)
2) Execute the U021 Memory initializing to initialize the controller backup memory
An error is detected at the and check function.
F36X
Print management section 3) Replace the main board and check function.
4) Replace the HDD and check function.
5) Retrieve the USBLOG and contact the Service Administrative Division.
1) Format the HDD and check function. (U024 FULL formatting)
2) Execute the U021 Memory initializing to initialize the controller backup memory
and check function. F14A,F14F:KUIO error
3) Execute the U671 Clear FAX back up data (FAX DIMM clear) and check Main board (USB hub)
An error is detected at the function.
F37X
FAX management section (Take cae of the received data since it is cleared) [Main-KUIO Interface]
4) Replace the FAX_DIMM and check function. Main board: YC8,YC9
5) Replace the main board and check function. KUIO board: YC3,YC4
6) Replace the HDD and check function.
7) Retrieve the USBLOG and contact the Service Administrative Division.
1) Format the HDD and check function. (U024 FULL formatting)
2) Execute the U021 Memory initializing to initialize the controller backup memory
An error is detected at the
and check function.
F38X Authentication/permit
3) Replace the main board and check function.
management section
4) Replace the HDD and check function.
5) Retrieve the USBLOG and contact the Service Administrative Division.
F3AX
F3BX
F3CX
F3DX 1) Format the HDD and check function. (U024 FULL formatting)
F3EX 2) Execute the U021 Memory initializing to initialize the controller backup memory
F3FX An error is detected at the and check function.
F40X Entity management section 3) Replace the main board and check function.
F41X 4) Replace the HDD and check function.
F42X 5) Retrieve the USBLOG and contact the Service Administrative Division.
F43X
F44X
F45X
*The F46F is printer
1) Replace the main board and check function. process error. if it repeats
An error is detected at the
F46X 2) Retrieve the USBLOG with a certain print data,
Print image process section
(or retrieve the print capture data by case) retrieve the capture data
and USBLOG.
 C031_SystemError(Fxxx)Outline 6/8
No. Content Check procedure & check point Remark 1 Remark 2

F47X 1) Format the HDD and check function. (U024 FULL formatting)
2) Execute the U021 Memory initializing to initialize the controller backup memory
An error is detected at the
and check function.
F48X Image edit process control
3) Replace the main board and check function.
section
4) Replace the HDD and check function.
F49X 5) Retrieve the USBLOG and contact the Service Administrative Division.
1) Format the HDD and check function. (U024 FULL formatting)
F4AX 2) Execute the U021 Memory initializing to initialize the controller backup memory
An error is detected at the and check function.
Print image process section 3) Replace the main board and check function.
F4CX 4) Replace the HDD and check function.
5) Retrieve the USBLOG and contact the Service Administrative Division.
1) Format the HDD and check function. (U024 FULL formatting)
F4DX 2) Execute the U021 Memory initializing to initialize the controller backup memory
An error is detected at the and check function.
Entity control section 3) Replace the main board and check function.
F4EX 4) Replace the HDD and check function.
5) Retrieve the USBLOG and contact the Service Administrative Division.
1) Format the HDD and check function. (U024 FULL formatting)
2) Execute the U021 Memory initializing to initialize the controller backup memory
An error is detected at the and check function.
F4FX
Job control section 3) Replace the main board and check function.
4) Replace the HDD and check function.
5) Retrieve the USBLOG and contact the Service Administrative Division.
1) Format the HDD and check function. (U024 FULL formatting)
2) Execute the U021 Memory initializing to initialize the controller backup memory
An error is detected at the and check function.
F50X
FAX control section 3) Replace the main board and check function.
4) Replace the HDD and check function.
5) Retrieve the USBLOG and contact the Service Administrative Division.
F51X 1) Format the HDD and check function. (U024 FULL formatting)
F52X 2) Execute the U021 Memory initializing to initialize the controller backup memory
F53X An error is detected at the and check function.
F55X Job execution section 3) Replace the main board and check function.
F56X 4) Replace the HDD and check function.
F57X 5) Retrieve the USBLOG and contact the Service Administrative Division.
F58X
1) Format the HDD and check function. (U024 FULL formatting)
F59X
2) Execute the U021 Memory initializing to initialize the controller backup memory
F5AX
An error is detected at the and check function.
F5BX
Service management section 3) Replace the main board and check function.
F5CX
4) Replace the HDD and check function.
F5DX
5) Retrieve the USBLOG and contact the Service Administrative Division.
F5EX
 C031_SystemError(Fxxx)Outline 7/8
No. Content Check procedure & check point Remark 1 Remark 2
1) Format the HDD and check function. (U024 FULL formatting)
2) Execute the U021 Memory initializing to initialize the controller backup memory
An error is detected at the and check function.
F5FX
Service execution section 3) Replace the main board and check function.
4) Replace the HDD and check function.
5) Retrieve the USBLOG and contact the Service Administrative Division.
1) Format the HDD and check function. (U024 FULL formatting)
2) Execute the U021 Memory initializing to initialize the controller backup memory
An error is detected at the
and check function.
F60X Maintenance mode
3) Replace the main board and check function.
management section
4) Replace the HDD and check function.
5) Retrieve the USBLOG and contact the Service Administrative Division.
1) Format the HDD and check function. (U024 FULL formatting)
2) Execute the U021 Memory initializing to initialize the controller backup memory
An error is detected at the and check function.
F61X
Report compiling section 3) Replace the main board and check function.
4) Replace the HDD and check function.
5) Retrieve the USBLOG and contact the Service Administrative Division.
1) Format the HDD and check function. (U024 FULL formatting)
2) Execute the U021 Memory initializing to initialize the controller backup memory
An error is detected at the and check function.
F62X
Service execution section 3) Replace the main board and check function.
4) Replace the HDD and check function.
5) Retrieve the USBLOG and contact the Service Administrative Division.
1) Format the HDD and check function. (U024 FULL formatting)
2) Execute the U021 Memory initializing to initialize the controller backup memory
An error is detected at the and check function.
F63X
Device control section 3) Replace the main board and check function.
4) Replace the HDD and check function.
5) Retrieve the USBLOG and contact the Service Administrative Division.
F64X 1) Format the HDD and check function. (U024 FULL formatting)
2) Execute the U021 Memory initializing to initialize the controller backup memory
F65X An error is detected at the and check function.
F66X Print image process section 3) Replace the main board and check function.
4) Replace the HDD and check function.
F67X 5) Retrieve the USBLOG and contact the Service Administrative Division.
1) Format the HDD and check function. (U024 FULL formatting)
2) Execute the U021 Memory initializing to initialize the controller backup memory
An error is detected at the
and check function. *F684 is Overwrite error
F68X Storage device control
3) Replace the main board and check function. with the HDD security kit
section
4) Replace the HDD and check function.
5) Retrieve the USBLOG and contact the Service Administrative Division.
 C031_SystemError(Fxxx)Outline 8/8
No. Content Check procedure & check point Remark 1 Remark 2
F69X 1) Format the HDD and check function. (U024 FULL formatting)
2) Execute the U021 Memory initializing to initialize the controller backup memory
F6AX An error is detected at the and check function.
F6BX HyPAS control section 3) Replace the main board and check function.
4) Replace the HDD and check function.
F6CX 5) Retrieve the USBLOG and contact the Service Administrative Division.
F6DX
F6EX
1) Check the external server and check function.
F6FX
2) Chekc the connection to the external server and check function.
F70X An error is detected at the
3) Check the network settings and check function.
F71X External Server management *FieryOption related
4) Replace the bridge board and check function.
F72X section
5) Replace the main board and check function.
F73X
6) Retrieve the USBLOG and contact the Service Administrative Division.
F74X
F75X