Close Control EC Plug Fan Range

Engineering Data Manual

Chilled Water & Air Cooled R410A
50/60Hz
 ENGINEERING DATA MANUAL 50/60Hz

Index
Description Page

EDPAC Company Profile 3

This Product Range 3

Associated Product Ranges 3

Equipment Nomenclature 4

EC Plug Fan Range Dimensions and Weights 4

Air Cooled Condensers - Dimensions and Weights 5

Guide Specifications 6

General Engineering Details - Air Cooled 10

General Engineering Details - Chilled Water 11

Air Cooled System Schematic 12

Chilled Water Cooled System Schematic 13

Air Cooled Unit Capacities 14

Standard Chilled Water Unit Capacities - 4 Row 15

Standard Chilled Water Unit Capacities - 6 Row 16

Fan Under Floor Chilled Water Unit Capacities - 4 Row 17

Fan Under Floor Chilled Water Unit Capacities - 6 Row 18

Electrical Details - Air Cooled Units 19

Electrical Details - Chilled Water Units 20

While every precaution has been taken to ensure accuracy and completeness in this manual, EDPAC assumes no responsibility, and disclaims
all liability for damages resulting from use of this information or for any errors or omissions.

Document Reference: E4.19-01-05-03

2
 EDPAC COMPANY PROFILE
HISTORY
Formed in 1968, EDPAC has grown through worldwide distribution to an installed base of over 50,000 units. EDPAC currently
services the markets of Europe, the Americas, the Middle East, and the Far East. As one of the pioneers of Precision Air Conditioning
the EDPAC name has become synonymous with quality and reliability. With its highly skilled and experienced team EDPAC has
established not only a modern manufacturing plant, but also a sophisticated and innovative product development programme. Since
1987 EDPAC International located in Cork Ireland, has controlled the entire activities of the group.
PRODUCT RANGE
EDPAC manufactures a broad range of Precision Air Conditioning equipment for the Computer Room, Telecoms and other critical
Building Services applications. EDPAC systems are designed to provide optimum operating conditions in close control
environments.
QUALITY
All suppliers of materials and components used in manufacturing are assessed and qualified by EDPAC. The EDPAC guarantee of
quality is also complimented by rigorous in-factory quality assessment and quality control testing prior to product dispatch. The
overall activity of the factory is customer focused and conforms to the strict norms of IS/ISO9001/EN29001. EDPAC was awarded
and has retained this certificate since 18th March 1992.

THIS PRODUCT RANGE

CLOSE CONTROL EC PLUG FAN

The EDPAC Close Control EC Plug Fan Range units are precision environmental control units designed for 24 hour, year-round use.
As standard the units are equipped with: Scroll Compressors, Electrode Steam Boiler Humidifiers, Stainless Steel Tubular Finned
Electric Reheat, G4 Filtration, EC Plug Fans and R410A Refrigerant. BMS interface cards are available for all of the most commonly-
used protocols including but not limited to MODBUS, BACnet, LON, JCI METASYS & they all can be integrated into most BMS
systems by RS 485 or over TCP/IP. Cooling media available is air cooled direct expansion & chilled water. There is an option for a
dual cooling version with the addition of a chilled water coil to air cooled unit or an additional chilled water coil to a chilled water
unit. The unit simultaneously controls air temperature, air humidity, air distribution and air cleanliness in the conditioned space. It is
fitted with a central microprocessor controller which monitors air temperature/humidity and air cleanliness and ensures accurate
stepped response to room load changes. To maximise energy efficiency, all units are fitted with wide surface area coils EC plug fans
and our air cooled units have electronic expansion valves. All major components are fully serviceable from the front.

ASSOCIATED PRODUCT RANGES

CLOSE CONTROL MODULAR UNIT RANGE

The Close Control Modular range is comprised of 4 module sizes providing nominal capacities of 10, 15, 20, 25, 30, 35 & 40 kW per
module. These modules form the basis of the EDPAC modular concept. Unit selections can be based on a single module for a single
circuit system or any combination of 2 modules to give a twin circuit or Duplex system. The Duplex configuration is advantageous as
both modules can be positioned at different locations within the room.

CLOSE CONTROL AIR COOLED TWIN CIRCUIT UNIT RANGE

The Close Control Twin Circuit range comprises 4 sizes providing nominal capacities of 30, 40, 50, 60, 70, 80 & 100 in 10kW
increments. Units are twin circuit in a single frame and are available in upflow and downflow configurations. Cooling media
available is air cooled direct expansion only. There is an option for a dual cooling version with the addition of a chilled water coil.

SMALL SYSTEM UNIT RANGE

The Small Systems range comprises 2 unit sizes providing nominal capacities of 6, 12 and 18 kW. Units are available in downflow
with top return and upflow with front return. Cooling media include direct expansion using air and chilled water.

TELECOM SYSTEM UNIT RANGE

The Telecom System Unit range comprises of split DX units consisting of an indoor evaporator and outdoor condensing unit. There
are 3 unit sizes giving capacities of 5 to 20kW. The indoor unit can be wall or ceiling mounted optimising available room space. Units
are also available with freecooling & are ideally suited for small telecom sites, base stations and electrical rooms.

SELF CONTAINED UNIT RANGE

The Self Contained Unit range comprises of wall mounted self-contained DX units. There are 3 unit sizes giving capacities of 5 to
20kW. Units are mounted externally conserving internal floor space. Units are also available with freecooling & are ideally suited for
telecom sites and base stations.

3
 EQUIPMENT NOMENCLATURE

The EDPAC Close Control Plug Fan Range are precision environmental control units designed for 24 hour, year-round use. The unit
simultaneously controls air temperature, air humidity, air distribution and air cleanliness in the conditioned space. It is fitted with a
central microprocessor controller which monitors air temperature/humidity and air cleanliness and ensures accurate stepped response
to room load changes. To maximise energy efficiency, all units are fitted with wide surface area coils, compliant scroll compressors
and EC plug fans. Sound levels are kept to a minimum with double skin panels (optional), a unique wide area air chamber and coil
mounted filtration and fully isolated compressor compartment. All major components are fully serviceable from the front.

D ECP A 060 B S 1 1 S

S = STANDARD CONTROLS
G = GRAPHIC CONTROLS

HUMIDIFIER
0 = NONE
1 = STANDARD DISPOSABLE
2 = LOW CONDUCTIVITY
3 = CLEANABLE
4 = ULTRASONIC

HEATING
0 = NONE
1 = 2 STAGE
2 = 3 STAGE
3 = PROPORTIONAL
4 = HOT WATER

S = STANDARD SCROLL
COMPRESSOR
V = VARIABLE SPEED
COMPRESSOR
X = CHILLED WATER

VOLTAGE
B = 380-415/3/50
E = 220/3/60
H = 460/3/60
J = 380/3/60

NOMINAL CAPACITY
060 = 20 kW 200 = 80 kW
080 = 30 kW 240 = 100 kW
120 = 45 kW 280 = 115 kW
160 = 65 kW 320 = 140 kW

A = AIR COOLED
C = CHILLED WATER
D = DUAL COOLING

ECP = EC PLUG FAN

0 = AIR COOLED
D = DOWNFLOW 4 = 4 ROW CHILLED WATER
F = UPFLOW FRONT RETURN 6 = 6 ROW CHILLED WATER
B = UPFLOW BOTTOM RETURN
R = UPFLOW REAR RETURN
S = DOWNFLOW DISPLACEMENT
U = FAN UNDER FLOOR

EC PLUG FAN RANGE DIMENSIONS AND WEIGHTS

Dimensions (mm)

Model 064/6 080/4/6 120/4/6 160/4/6 200/4/6 240/4/6 280/4/6 324/6

Width - Chilled Water 650 850 1250 1650 2050 2450 2850 3250
Width - DX Units N/A 1250 1650 2050 2450 2850 3250 N/A
Depth 650 850 850 850 850 850 850 850
Height 1980 1980 1980 1980 1980 1980 1980 1980

Weight (kg)

Model 064/6 080/4/6 120/4/6 160/4/6 200/4/6 240/4/6 280/4/6 324/6

Chilled Water 260 315 380 470 530 625 695 795
DX Units N/A 405 580 640 710 915 975 N/A
Fan Under Floor N/A N/A N/A N/A 550 705 805 905
Dual Cooling 400 480 680 770 860 1095 1185 1260

4
 AIR COOLED CONDENSERS - DIMENSIONS AND WEIGHTS

CONDENSERS

Model 080 120 160 200 240 280

30°C Ambient Selection
Condenser Model - AGHS501C AGHS502B AGHS502A AGHS502B AGHS502B AGHS503B
Condenser Input Power kW 0.7 1.4 1.4 1.4 1.4 2.1
Condenser Quantity No. 1 1 2 2 2 2
Freefield SPL @ 10m dBA 43 46 46 46 46 48
Dimensions W x D mm 1050x825 1950x825 1950x825 1950x825 1950x825 2850x825
Weight - 1No / 2No kg 47 85 76 / 152 85 / 170 85 / 170 123 / 246
35°C Ambient Selection
Condenser Model - AGHS502A AGHS502C AGHS502A AGHS502B AGHS502C AGHS503B
Condenser Input Power kW 1.4 1.4 1.4 1.4 1.4 2.1
Condenser Quantity No. 1 1 2 2 2 2
Freefield SPL @ 10m dBA 46 46 46 46 46 48
Dimensions W x D mm 1950x825 1950x825 1950x825 1950x825 1950x825 2850x825
Weight - 1No / 2No kg 76 93 76 / 152 85 / 170 93 / 186 123 / 246
40°C Ambient Selection
Condenser Model - AGHS502B AGHS503B AGHS502B AGHS503A AGHS503B AGHS504B
Condenser Input Power kW 1.4 2.1 1.4 2.1 2.1 2.8
Condenser Quantity No. 1 1 2 2 2 2
Freefield SPL @ 10m dBA 46 48 46 48 48 49
Dimensions W x D mm 1950x825 2850x825 1950x825 2850x825 2850x825 3750x825
Weight - 1No / 2No kg 85 123 85 / 170 110 / 220 123 / 246 178 / 356
45°C Ambient Selection
Condenser Model - AGHS502C AGHS504B AGHS503B AGHS503B AGHS504B AGHS633C
Condenser Input Power kW 1.4 2.8 2.1 2.1 2.8 4.2
Condenser Quantity No. 1 1 2 2 2 2
Freefield SPL @ 10m dBA 46 49 48 48 49 53
Dimensions W x D mm 1950x825 3750x825 2850x825 2850x825 3750x825 3150x1030
Weight - 1No / 2No kg 93 178 123 / 246 123 / 246 178 / 356 257 / 514
50°C Ambient Selection
Condenser Model - AGHS503B AGHS504C AGHS503B AGHS504B AGHS504C AGHS635C
Condenser Input Power kW 2.1 2.8 2.1 2.8 2.8 7.0
Condenser Quantity No. 1 1 2 2 2 2
Freefield SPL @ 10m dBA 48 49 48 49 49 55
Dimensions W x D mm 2850x825 3750x825 2850x825 3750x825 3750x825 5150x1030
Weight - 1No / 2No kg 123 192 123 / 246 178 / 356 192 / 384 420 / 840

Notes:
1. Standard condensers have 4 Pole motors. For 6 Pole & 8 Pole low noise versions, consult factory.
2. All condensers are shipped with mounting feet. When mounted in the horizontal, condenser models AGHS 501 – 504 are 850
mm high and Condenser models AGHS 633 – 635 are 1170 mm high.
3. All condenser data is per condenser.

5
 GUIDE SPECIFICATIONS

STANDARD FEATURES

EC Plug Fans Cooling Coil

The EC plug fan is a backward curved fan with integrated EC The cooling coils shall be multi-row constructed from copper
electrically commutated motor which is controlled directly tubes with aluminium fins. Large surface areas shall ensure
from the microprocessor using a 0-10V output. Options on high sensible heat ratios and low airside pressure drops,
setup are: resulting in reduced fan power requirements and noise levels.

Unit is set up with a discrete fan speed based on a fixed 0-10V DX Units
output to the EC motor based on the design point of operation
Each unit shall have 2 independent refrigerant circuits, each
of the fan. This is the default setting on units shipped.
with a liquid distributor, expansion valve, sight glass and filter
drier.
Unit set up to track the control temperature band with set
voltage limits whereby max voltage / fan air volume is at set
point plus/minus control band & min voltage / fan air volume Electronic Expansion Valve
at set point. Max air volume is typically design air volume & DX circuits are fitted with electronic expansion valves which
min air volume is around 60% for chilled water units & 75% provide precision proportional control and annualised energy
for air cooled units. This is something that can be proven on savings of 15-20% with floating condenser head pressure
site. Minimum value needs to ensure there are no hot spots control.
due to lack of airflow & that there is no loss of sensible
cooling capacity to latent cooling capacity at the cooling Motors
coil.
The motor shall comply with IP55 TEFC insulated to Class F.
Unit set up to give a reduced fan air volume in
dehumidification mode to conserve energy in Filtration
dehumidification while quickly achieving the
The filters shall be 100mm thick disposable pleated panel
dehumidification effect at the cooling coil. This output voltage
filter rated G4 in accordance with EN779. They shall be fitted
is again user selectable.
in the return air stream and be accessible from the front of a
Upflow unit and the top of a Downflow unit & Displacement
Unit is set up via an underfloor pressure transducer to give a
unit.
fixed underfloor pressure all the time. Underfloor pressure
setpoint is input through the unit user display.
Compressors
Unit is set up to provide a guaranteed supply air temperature Compressors shall be high efficiency hermetically sealed
in the cold aisle. scroll type. High and low pressure switches, motor overload
protection and crankcase heaters shall be provided. The
Unit is set up to be controlled by a BMS with minimum & compressors shall be mounted on resilient neoprene
maximum voltage values & 0-100% output over these values mountings for vibration isolation.
by BMS.
Electrical Panel
Unit is set to have an airflow setpoint on controller with the
addition of a fan inlet measuring ring & pressure transducer in The electrical panel shall be constructed and assembled in
the unit. compliance with IEC standards with all components VDE
approved. All sub circuits are protected by MCB’s. The high
and low voltage sections shall be segregated and all high
Cabinet
voltage electrical components shall be touch safe.
The cabinet frames shall be constructed of formed 2.0 mm
Zintec steel sections. Paint finish is Epoxy Powder Coated Electric Heaters
with an “Orange Peel” textured finish. Interior panels to be
manufactured from galvanised steel in all cases. Exterior Electric heaters shall have stainless steel sheathed elements
panels are to be as cabinet except in 1.2 mm Zintec. Paint with stainless steel finning, balanced over three phases and
Colour to be RAL 9018. The front panels shall be fastened to rated to operate at black heat. Control shall be in two stages.
the frame using quarter turn fasteners. Side panels shall be Protection is by a high temperature safety cut-out stat. The stat
secured to the frame using chrome plated screws. All panels shall be a capillary type mounted in the airstream resettable
shall be flush fitting, sealed to the frame sections with closed from the control section of the electrical panel.
cell foam and insulated with a non-shedding material, which
shall be non-combustible, when tested in accordance with B.S.
476 Part 6 and 7. The units shall be fully accessible and
serviceable from the front.
6
 GUIDE SPECIFICATIONS
Manual Procedure: With the unit powered off & the controls
Humidification powered on it shall be possible to check all analogue & digital
outputs & to run the devices.
The humidifier shall be of the electrode-boiler type. Features
shall include selectable steam output and microprocessor
control with alarms and diagnostic facilities. The humidifier Temperature & Humidity Zone setback: It shall be possible to
control system shall allow the use of a wide range of mains create up to 4 periods in a 24 hour period with dedicated set
water conditions namely: inlet mains water pressure of 1-10 points of temperature & humidity.
bar, total hardness of 15-30 French degrees & water inlet
electrical conductivity of 400-800 micro siemens. Unit shall System Auto Restart: For start up after power failure, the unit
optimise drain down frequency for maximum operational shall automatically restart with an ability to stagger the
economy. starting of multiple units by setting a time delay of up to 999
seconds.
Microprocessor Controls
Security: The microprocessor shall have multiple levels of
All units shall be fitted as standard with the latest Delta range
security (5 no. 4 digit passwords) to prevent unauthorised
of DIN rail mounted Microprocessor Controls. The Control
parameter adjustment.
System utilises a main Microprocessor Interface Board
equipped with a set of terminals necessary to connect the
Time Delays: It shall be possible to create or adjust if
Board to the controlled devices (e.g. valves, compressors,
necessary the unit on time delay, settle delay, unit off time
fans, reheats, sensors and humidifiers). All software is
delay, compressor interstage delay, compressor minimum run
permanently stored in flash RAM and is therefore protected
time, compressor minimum stop time, heater interstage delay,
even in the event of a power failure. Unit software is uploaded
winter start time delay, temperature alarm time delay,
to the Microprocessor using a RAM key or personal
humidity alarm time delay, serious alarm time delay & non-
computer. On multi unit sites this quickens unit
serious alarm time delay.
commissioning. The software can also be easily changed or
upgraded on site by qualified service personnel.
Sensor Calibration: It shall be possible to recalibrate the
temperature & humidity sensors in software.
The Microprocessor based Terminal Unit is complete with a 4
line x 20 character backlit LCD Display, keypad and LED
Inputs / Outputs: It shall be possible to view the current status
Indicators allowing the user to easily set the main control
of all inputs & outputs while the unit is running.
parameters (set-points, differentials and alarm thresholds) and
carry out the main working operations (on/off and displaying
Set & Hysteresis adjustment: It shall be possible to adjust the
controlled variables).
set & hysteresis % values of stepped outputs within the
control.
Main features of controller are:
BMS / BAS interfacing: It shall be possible with the addition
Status: The display shall indicate current temperature, current
of a simple communications card to communicate all Analog,
humidity, temperature & humidity set points, cooling status,
Digital & Integer variables in the following protocols : LON
heating status, humidification status & dehumidification status
FTT 10, BACnet over RS485 MSTP, BACnet over TCP/IP,
SNMP over TCP/IP, MODBUS over RS485, Metasys & OPC
Redundancy Management & Master Control: The controls
Server.
shall be capable of redundancy management & master control
setup / “Handshake” of groups of up to 16 units without Remote Display panel: It shall be possible to connect an
addition of any hardware. additional shared LCD display which is wired back to the unit
& this remote display shall have full control access to the unit
Alarms: Controls shall be capable of storing last 100 alarms, from a distance of up to 100m.
identified by type, date stamped & indicating also the Remote Temperature & Humidity sensing: It shall be possible
temperature & humidity conditions when the alarm occurred to remotely locate the Temperature/Humidity sensor to better
& also the setpoints of temperature & humidity when the meet the sites cooling needs. The sensor can be located a
alarm occurred. There are 36 alarms & all alarms can be either distance of up to 30m from the unit.
set as “serious” or “non-serious”. A serious alarm shuts down
the unit.

Hours Thresholds: It shall be possible to set run hours

thresholds for major components to facilitate preventative
maintenance.

7
 GUIDE SPECIFICATIONS

OPTIONAL FEATURES
Rear Return
3 Stage Reheat For upflow units. Required when unit is located in a service
Available instead of 2 stage by adding an electrical contactor area outside the conditioned space. Return air is taken in the
& configuring the software to 3 stage. rear. Rear panel generally has a duct connection and filters are
withdrawable from outside the unit.
Proportional Electric Reheat
Bottom Return
Units shall be fitted with electric reheat controlled by a
thyristor giving a fully proportional 0-10V output of the reheat For upflow units. Required if air is returned from a floor void.
capacity. Bottom of unit is opened up and base components are
mounted on rails. Filters cannot be fitted in unit and are
Hot Water Reheat shipped loose for installation beneath the unit on site.

Units shall be fitted with a Low Pressure Hot Water (LPHW) Displacement
heating coil in place of the standard electrical heating. Water
flow through the coil is controlled by a 2 or 3 way modulating For units where the air is discharged at a low level above the
valve. Duties of these coils are nominally the same as standard floor.
electric heating, based on flow and return hot water
temperatures of 82°C and 71°C respectively. Fan Under Floor
For units where the fan is placed in the base of the unit and the
Cleanable Humidifier Cylinder coil is extended to give an increased capacity.
Humidifier cylinder is serviceable whereas standard
humidifier cylinder is disposable. Return Air Attenuator 500mm high
Attenuator mounted on top of downflow unit. Attenuators
Low Conductivity Humidifier Cylinder have internal baffles and provide 8-10 dB reduction on
Disposable type but for water supply with low electrical airborne noise.
conductivity.
F5/6/7 Panel Filters
Floor Stand Upgrade of standard G4 disposable panel filters to F5/6/7
Floorstands are shipped flat-pack and need to be assembled on disposable panel filters.
site. They are suitable for raised floor heights of 150mm to
600mm. The legs are notched at 50mm intervals for cutting G2 Pre-filter with G4 Main Filter
on site. There is also a final adjustment on the foot of +/-
100mm G4 disposable filter replaced with 50mm G2
50mm. Floorstands are manufactured from galvanised steel.
disposable plus 50mm G4 disposable filter.
Damper & On/Off Actuator Kit
Washable Filters
Addition of a damper & on/off actuator to isolate a downflow
Upgrade of standard disposable 100mm G4 disposable filters
or upflow unit in standby. Damper is typically fitted on top of
to washable 50mm G3 type plus 50mm G4 disposable filter.
unit. Actuator powered from unit electrical panel.

Air Discharge Plenum Filter Clog

An additional pressure differential switch mounted in the unit
For Upflow units which are to be installed in a freeblow
to sense airside pressure drop across the filters. Once the
situation. Plenum consists of an insulated sheet metal
pressure drop is exceeded a filter clog (filter change) alarm is
assembly with 3 discharge grilles. Grilles are double deflector
generated.
type. Plenum colour will match unit colour. Plenums can also
be manufactured as 1 way or 2 way discharge, please consult
factory. Different Unit Colour
Units can be manufactured in a different colour to the standard
VSD Scroll Compressor RAL 9018. RAL number to be specified.
Variable speed scroll compressor which can modulate from 25
to 100rps. This gives additional energy savings, more accurate Double Skin Panels
temperature & humidity control, reduced inrush current & All units. Inner perforated galvanized steel or solid painted or
reduced on / off cycles. unpainted galvanized steel.

8
 GUIDE SPECIFICATIONS
A fire stat shall be provided & mounted in the return air path
Fresh Air Connection Units can be supplied with a fresh within the unit to interface with the unit controls and indicate
air inlet connection and disposable G4 filter. This will admit an alarm.
approximately 3-5% of the recirculated air volume.
Water Detection – Point Type
Hot Gas Bypass Consists of a water detection module mounted in unit & point
sensor which can be placed in unit or under the floor. Multiple
Hot gas bypass line including hot gas bypass valve fitted to point sensors can be placed in series with each other. A cable
provide capacity control in low load situations. type water warning is also available.

Liquid Receiver RS 485 Communications Card

Liquid receiver fitted in unit base of indoor unit. Receiver is Serial interface card for Microprocessor board. For BMS
complete with rotalock valve on the discharge. setup. Can communicate on Delta 2 own Protocol & Modbus
without an external Gateway.
Oil Separator
Oil separator fitted in indoor unit to prevent migration of oil BACnet over RS 485
away from compressor. Serial interface card for Microprocessor board. For BMS
setup. Runs on BACnet protocol over RS 485. Final setup by
VSD Scroll Compressor BMS system integrator.
Variable speed scroll compressor which can modulate from 25
to 100rps. This gives additional energy savings, more accurate BACnet over TCP/IP
temperature & humidity control, reduced inrush current & Serial interface card for Microprocessor board. For BMS
reduced on / off cycles setup. Runs on BACnet protocol over TCP/IP. Final setup by
BMS system integrator.
Compressor Acoustic Jacket
High mass barrier insulation to reduce compressor noise. SNMP over TCP/IP
Serial interface card for Microprocessor board. For BMS
Condensate Pump setup. Runs on SNMP protocol over TCP/IP. Final setup by
Where, due to location, it is not possible to gravity drain units, BMS system integrator.
a condensate pump can be fitted to collect any condensate and
pump it to the nearest convenient drain point (pump duty is 6 LON Communication Card
l/min Vs 6 m head). A cheaper cold condensate pump is Serial interface card for Microprocessor board. For BMS
available for units without humidifiers. setup. Runs on LON FTT 10 protocol. Final setup by LON
system integrator.
Handshake - Autosequence / Autorotate
For interconnection of up to 16 units by means of a shielded Condenser Factory Wired Disconnect
twisted pair cable from interface board to interface board Factory wired disconnect fitted to condenser.
between units. This shall provide N+1 with one unit always in
standby in case of duty unit failure. Standby unit shall be
MCB and Contactor Condenser Control
rotated over time. Changeover shall be set between 1- 168
hours (1 hour – 1 week). In case of high temperature alarm MCB and contactor fitted in unit per condenser providing
standby unit shall run & revert to standby once temperature is condenser on/off control interlocked with compressor.
corrected. In the group of up to 16 units, any number can be
running & any number can be set in standby. MCB, Contactor and Pressure Switch Condenser
Control
Smoke Detector
MCB, contactor and pressure switch fitted in unit per
A smoke detector shall be provided & mounted in the return condenser fan providing condenser on/off based on condenser
air path to interface with the unit controls and generate an fan activated on pressure switch pressure signal.
alarm.

Fire Detector
A fire detector shall be provided & mounted in the return air
path to interface with the unit controls and generate an alarm.

Fire Stat
9
 GUIDE SPECIFICATIONS

MCB, Contactor and Pressure Activated Fan Speed

Control
MCB and contactor per condenser fan. Condenser fans are all
220V/1 Ph and unit has a single or dual input Johnson
pressure activated fan speed control.

Condenser Fan Control with VSD

Uses a VSD to give a 0-10V proportional output to the
condenser to maintain refrigerant head pressure control.

Graphic Display
An optional Graphical Terminal Unit is also available. This is
a graphical display, LED Backlit with 132 x 64 pixel
graphical resolution.

10
 GENERAL ENGINEERING DETAILS – AIR COOLED

STANDARD MODELS

Model Size 080 120 160 200 240 280

Coil Data
Coil Face Area m2 0.87 1.38 1.87 2.36 2.86 3.37
Rows No. 4 4 4 4 4 4
Air Side Data
Air Volume m3/hr 7830 12420 16830 21235 25735 30330
External Static Pressure ESP Pa 25 25 25 25 25 25
Fan Type - EC EC EC EC EC EC
Fan Diameter mm 500 / 1 630 / 1 560 / 2 630 / 2 630 / 3 630 / 3
Fan Absorbed Power kW 1.3 1.8 1.1 1.4 1.3 1.6
Fan Motor kW 2.6 2.8 3.1 2.8 2.8 2.8
Filter Data
Grade - G4 G4 G4 G4 G4 G4
Filter Width mm 680 520 467 595 540 640
Filter Height mm 655 655 655 655 655 655
Filter Quantity No. 2 4 6 6 8 8
Noise Data
Freefield SPL dBA 58 58 59 61 61 62
Unit Piping Data
Discharge Connection Size mm 22 22 22 28 28 28
Liquid Connection Size mm 16 16 16 16 16 16
Condenser Piping Data
Condenser Conns. Inlet/Outlet 30°C mm 28/22 35/28 35/28 35/28 35/28 35/28
Condenser Conns. Inlet/Outlet 35°C mm 35/28 35/28 35/28 35/28 35/28 35/28
Condenser Conns. Inlet/Outlet 40°C mm 35/28 35/28 35/28 35/28 35/28 42/35
Condenser Conns. Inlet/Outlet 45°C mm 35/28 42/35 35/28 35/28 42/35 28/22
Condenser Conns. Inlet/Outlet 50°C mm 35/28 42/35 35/28 42/35 42/35 35/28
Condenser Quantity No. 1 1 2 2 2 2
Compressor Data
Scroll Compressor - 50Hz - ZP103 ZP182 ZP120 ZP154 ZP182 ZP235
Scroll Compressor - 60Hz - ZP90 ZP154 ZP103 ZP137 ZP154 ZP182
Compressor Quantity - 1 1 2 2 2 2
Circuits - 2 2 2 2 2 2

Notes:
1. Indoor unit Freefield SPL dBA levels are measured at 3m.
2. All filters are 97mm thick.
3. Humidifier inlet connection is ¾’’ BSPM & drain connection is 1’’ BSPF.
4. Coil drain pan connection is ¾’’ BSPF.

11
 GENERAL ENGINEERING DETAILS – CHILLED WATER
STANDARD MODELS
Model Size 064/6 084/6 124/6 164/6 204/6 244/6 284/6 324/6
Coil Data
Coil Face Area m2 0.58 0.82 1.32 1.82 2.31 2.81 3.32 3.83
Rows No. 4&6 4&6 4&6 4&6 4&6 4&6 4&6 4&6
Air Side Data
Air Volume m3/hr 5665 7830 12420 16830 21235 25735 30330 34920
External Static Pressure ESP Pa 25 25 25 25 25 25 25 25
Fan Type - EC EC EC EC EC EC EC EC
Fan Diameter / Fan Quantity mm 450 / 1 500 / 1 630 / 1 560 / 2 630 / 2 630 / 3 630 / 3 630 / 4
Fan Absorbed Power - 4 Row kW 0.9 1.3 1.8 1.1 1.3 1.0 1.2 0.9
Fan Motor Power kW 1.45 2.6 3.6 3.1 2.8 2.8 2.8 2.8
Fan Absorbed Power - 6 Row kW 1.1 1.6 2.2 1.4 1.7 1.3 1.6 1.2
Fan Motor Power kW 1.45 2.6 3.6 3.1 2.8 2.8 2.8 2.8
Filter Data
Grade - G4 G4 G4 G4 G4 G4 G4 G4
Filter Width mm 490 685 540 490 625 570 670 615
Filter Height mm 660 660 660 660 660 660 660 660
Filter Quantity No. 2 2 4 6 6 8 8 10
Noise Data
Freefield SPL dBA 57 58 58 59 61 61 62 62
Unit Piping Data
Chilled Water F&R Pipe Size mm 35 35 42 54 54 54 54 54
Control Valve Size mm 32 32 32 40 40 50 50 50
Control Valve Quantity No. 1 1 1 1 1 1 1 1
Control Valve Kv - 16 16 16 25 25 40 40 40

FAN UNDER FLOOR MODELS

Model Size 204/6 244/6 284/6 324/6
Coil Data
Coil Face Area m2 3.16 3.85 4.55 5.26
Rows No. 4&6 4&6 4&6 4&6
Air Side Data
Air Volume m3/hr 28420 34685 40950 47375
External Static Pressure ESP Pa 25 25 25 25
Fan Type - EC EC EC EC
Fan Diameter / Fan Quantity mm 630 / 2 630 / 3 630 / 3 630 / 4
Fan Absorbed Power - 4 Row kW 2.1 1.4 1.9 1.4
Fan Motor Power kW 3.6 2.8 3.6 2.8
Fan Absorbed Power - 6 Row kW 2.3 1.6 2.2 1.6
Fan Motor Power kW 3.6 2.8 3.6 2.8
Filter Data
Grade - G4 G4 G4 G4
Filter Width mm 625 570 670 615
Filter Height mm 600 600 600 600
Filter Quantity No. 9 12 12 15
Noise Data
Freefield SPL dBA 61 61 62 62
Unit Piping Data
Chilled Water F&R Pipe Size mm 54 54 67 67
Control Valve Size mm 50 50 50 50
Control Valve Quantity No. 1 1 1 1
Control Valve Kv - 40 40 40 40
Notes:
1. Indoor unit Freefield SPL dBA levels are measured at 3m.
2. All filters are 97mm thick.
3. Humidifier inlet connection is ¾’’ BSPM & drain connection is 1’’ BSPF.
4. Coil drain pan connection is ¾’’ BSPF.

12
 AIR COOLED SYSTEM SCHEMATIC

1 2 3 4 5 6

Suction
Line
9 Discharge
Line 11
10
8
M
8 7

12
13

14

15 Liquid
Line

System Components
1. Evaporator Coil.
2. Liquid Distributor.
3. Thermostatic Expansion Valve (externally equalised).
4. Liquid Line Solenoid Valve (optional).
5. Liquid Sight Glass (including moisture indicator).
6. Filter Drier.
7. Compressor.
8. Compressor Service Valves.
9. High Pressure Switch (manual reset).
10. Low Pressure Switch (automatic reset).
11. Check Valve (See Note).
12. Fan speed Controller (pressure operated head pressure control, if fitted).
13. Pressure relief Valve (See Note).
14. Air Cooled Condenser.
15. Liquid Receiver (See Note).

Note: Items 11, 13 and 15 are supplied by others and field fitted by others.

13
 CHILLED WATER COOLED SYSTEM SCHEMATIC

3 Way Valve System

1
2
M

Chilled Water Return Chilled Water Flow

4 4

2 Way Valve System

.

Chilled Water Return Chilled Water Flow

3 3

System Components

3 Way Valve System 2 Way Valve System

1 Chilled Water Coil Chilled Water Coil
2 Balancing Orifice 2 Way Modulating Valve
3 3 Way Modulating Valve Isolating Valves
4 Isolating Valves

Note: Isolating valves are field fitted by others.

14
 AIR COOLED UNITS - COOLING CAPACITIES 50Hz

Model : Standard 080 120 160 200 240 280

Air On: 22oC, 50% RH
Total Capacity kW 23.5 40.4 54.4 68.6 80.8 105.0
Sensible Capacity kW 21.4 36.4 49.0 60.4 72.7 98.7
Air On: 24oC, 50% RH
Total Capacity kW 24.4 41.8 56.2 71.0 83.6 108.8
Sensible Capacity kW 20.7 35.1 47.8 58.2 71.9 96.8
Scroll Compressor - ZP103 ZP182 ZP120 ZP154 ZP182 ZP235
Compressor Input Power kW 7.1 12.2 8.2 10.5 12.2 15.9
Compressor Quantity No. 1 1 2 2 2 2
Airflow m3/hr 7830 12420 16830 21235 25735 30330
No. of Fans No. 1 1 2 2 3 3
Fan Motor kW 2.6 2.8 3.1 2.8 2.8 2.8
EC Fan Diameter mm 500 630 560 630 630 630
Electric Reheat kW 9.6 15.0 25.0 25.0 25.0 25.0
No. of Steps No. 2 2 2 2 2 2
Humidifier Capacity kg/hr 3 8 8 8 8 8
Humidifier Power kW 2.2 5.8 5.8 5.8 5.8 5.8

AIR COOLED UNITS - COOLING CAPACITIES 60Hz

Model : Standard 080 120 160 200 240 280

Air On: 22oC, 50% RH
Total Capacity kW 24.3 41.4 57.2 72.2 82.2 96.8
Sensible Capacity kW 22.1 37.3 51.5 63.5 74.0 91.0
Air On: 24oC, 50% RH
Total Capacity kW 25.2 42.6 59.2 74.8 85.2 100.2
Sensible Capacity kW 21.4 35.8 50.3 61.3 73.3 89.2
Scroll Compressor - ZP90 ZP154 ZP103 ZP137 ZP154 ZP182
Compressor Input Power kW 7.6 12.6 8.5 11.1 12.6 14.8
Compressor Quantity No. 1 1 2 2 2 2
Airflow m3/hr 7830 12420 16830 21235 25735 30330
No. of Fans No. 1 1 2 2 3 3
Fan Motor kW 2.6 2.8 3.1 2.8 2.8 2.8
EC Fan Diameter mm 500 630 560 630 630 630
Electric Reheat kW 9.6 15.0 25.0 25.0 25.0 25.0
No. of Steps No. 2 2 2 2 2 2
Humidifier Capacity kg/hr 3 8 8 8 8 8
Humidifier Power kW 2.2 5.8 5.8 5.8 5.8 5.8

Notes:
1. Capacities are based on R410A refrigerant.
2. For capacities at other conditions, please refer to the Factory or product selection program.

15
 CHILLED WATER COOLED UNITS - COOLING CAPACITIES 50/60Hz

4 ROW COIL - 6/12C

Model : Standard 064 084 124 164 204 244 284 324
Air On: 22oC, 50% RH
Total Capacity kW 17.0 24.3 40.5 55.5 72.4 85.2 102.6 119.7
Sensible Capacity kW 17.0 24.3 40.5 55.5 72.4 85.2 102.6 119.7
Chilled Water Flow l/s 0.71 1.02 1.69 2.32 3.03 3.56 4.29 5.02
Unit Pressure Drop kPa 11 15 29 24 43 29 44 61
Air On: 24oC, 50% RH
Total Capacity kW 20.0 28.6 47.2 64.7 84.3 99.8 119.7 125.4
Sensible Capacity kW 20.0 28.6 47.2 64.7 76.1 99.8 108.3 119.7
Chilled Water Flow l/s 0.84 1.19 1.98 2.70 3.52 4.16 5.00 5.22
Unit Pressure Drop kPa 14 19 40 32 58 39 57 66
Airflow m3/hr 5665 7830 12420 16830 21235 25735 30330 34920
No. of Fans No. 1 1 1 2 2 3 3 4
Fan Motor kW 1.45 2.6 3.6 3.1 2.8 2.8 2.8 2.8
EC Fan Diameter mm 450 500 630 560 630 630 630 630
Electric Reheat kW 7.5 9.6 15.0 25.0 25.0 25.0 25.0 25.0
No. of Steps No. 2 2 2 2 2 2 2 2
Humidifier Capacity kg/hr 3 3 8 8 8 8 8 8
Humidifier Power kW 2.2 2.2 5.8 5.8 5.8 5.8 5.8 5.8

4 ROW COIL - 7/12C

Model : Standard 064 084 124 164 204 244 284 324
Air On: 22oC, 50% RH
Total Capacity kW 16.7 23.8 39.4 54.0 70.3 82.9 99.8 116.9
Sensible Capacity kW 16.7 23.8 39.4 54.0 70.3 82.9 99.8 116.9
Chilled Water Flow l/s 0.84 1.20 1.98 2.71 3.52 4.16 5.00 5.84
Unit Pressure Drop kPa 15 19 40 32 58 39 57 81
Air On: 24oC, 50% RH
Total Capacity kW 19.8 28.1 46.3 63.3 76.1 96.9 116.9 129.2
Sensible Capacity kW 19.8 28.1 46.3 63.3 73.2 96.9 116.9 121.6
Chilled Water Flow l/s 0.99 1.41 2.32 3.17 3.82 4.87 5.84 6.46
Unit Pressure Drop kPa 20 27 54 44 67 53 77 100
Airflow m3/hr 5665 7830 12420 16830 21235 25735 30330 34920
No. of Fans No. 1 1 1 2 2 3 3 4
Fan Motor kW 1.45 2.6 3.6 3.1 2.8 2.8 2.8 2.8
EC Fan Diameter mm 450 500 630 560 630 630 630 630
Electric Reheat kW 7.5 9.6 15.0 25.0 25.0 25.0 25.0 25.0
No. of Steps No. 2 2 2 2 2 2 2 2
Humidifier Capacity kg/hr 3 3 8 8 8 8 8 8
Humidifier Power kW 2.2 2.2 5.8 5.8 5.8 5.8 5.8 5.8

Notes:
1. Capacities are based on a 6oC / 7oC chilled water coil entering temperature & the tabulated flow rate.
2. For capacities at other conditions, please refer to the Factory or product selection program.

16
 CHILLED WATER COOLED UNITS - COOLING CAPACITIES 50/60Hz

6 ROW COIL - 8/14C

Model : Standard 066 086 126 166 206 246 286 326
Air On: 22oC, 50% RH
Total Capacity kW 16.8 24.2 41.6 57.1 72.0 89.1 106.4 124.5
Sensible Capacity kW 16.8 24.2 41.6 57.1 72.0 89.1 106.4 124.5
Chilled Water Flow l/s 0.71 1.01 1.74 2.39 3.01 3.73 4.46 5.19
Unit Pressure Drop kPa 9 12 29 25 33 36 53 74
Air On: 24oC, 50% RH
Total Capacity kW 20.4 29.2 49.4 67.7 85.5 105.5 125.4 146.3
Sensible Capacity kW 20.4 29.2 46.0 62.8 78.9 96.0 114.0 133.0
Chilled Water Flow l/s 0.85 1.22 2.07 2.83 3.57 4.40 5.25 6.10
Unit Pressure Drop kPa 13 18 42 35 46 49 72 101
Airflow m3/hr 5665 7830 12420 16830 21235 25735 30330 34920
No. of Fans No. 1 1 1 2 2 3 3 4
Fan Motor kW 1.45 2.6 3.6 3.1 2.8 2.8 2.8 2.8
EC Fan Diameter mm 450 500 630 560 630 630 630 630
Electric Reheat kW 7.5 9.6 15.0 25.0 25.0 25.0 25.0 25.0
No. of Steps No. 2 2 2 2 2 2 2 2
Humidifier Capacity kg/hr 3 3 8 8 8 8 8 8
Humidifier Power kW 2.2 2.2 5.8 5.8 5.8 5.8 5.8 5.8

6 ROW COIL - 9/14C

Model : Standard 066 086 126 166 206 246 286 326
Air On: 22oC, 50% RH
Total Capacity kW 16.4 23.6 39.9 54.7 69.1 85.1 101.7 117.8
Sensible Capacity kW 16.4 23.6 39.9 54.7 69.1 85.1 101.7 117.8
Chilled Water Flow l/s 0.83 1.18 2.00 2.75 3.47 4.27 5.10 5.93
Unit Pressure Drop kPa 12 17 39 33 44 46 68 95
Air On: 24oC, 50% RH
Total Capacity kW 20.0 28.4 47.6 65.2 82.3 100.7 120.7 139.7
Sensible Capacity kW 20.0 28.4 45.1 61.7 77.5 94.3 112.1 129.2
Chilled Water Flow l/s 1.00 1.43 2.39 3.27 4.13 5.07 6.04 7.01
Unit Pressure Drop kPa 17 24 55 46 61 63 94 130
Airflow m3/hr 5665 7830 12420 16830 21235 25735 30330 34920
No. of Fans No. 1 1 1 2 2 3 3 4
Fan Motor kW 1.45 2.6 3.6 3.1 2.8 2.8 2.8 2.8
EC Fan Diameter mm 450 500 630 560 630 630 630 630
Electric Reheat kW 7.5 9.6 15.0 25.0 25.0 25.0 25.0 25.0
No. of Steps No. 2 2 2 2 2 2 2 2
Humidifier Capacity kg/hr 3 3 8 8 8 8 8 8
Humidifier Power kW 2.2 2.2 5.8 5.8 5.8 5.8 5.8 5.8

Notes:
1. Capacities are based on an 8oC / 9oC chilled water coil entering temperature & the tabulated flow rate.
2. For capacities at other conditions, please refer to the Factory or product selection program.

17
 CHILLED WATER COOLED UNITS - COOLING CAPACITIES 50/60Hz

4 ROW COIL - 14/20C

Model : Fan Under Floor 204 244 284 324

Air On: 30oC, 30% RH
Total Capacity kW 91.2 114.7 137.8 161.0
Sensible Capacity kW 91.2 114.7 137.8 161.0
Chilled Water Flow l/s 3.83 4.81 5.78 6.78
Unit Pressure Drop kPa 27 43 50 71
Air On: 32oC, 30% RH
Total Capacity kW 106.4 133.2 160.0 186.9
Sensible Capacity kW 106.4 133.2 160.0 186.9
Chilled Water Flow l/s 4.48 5.60 6.72 7.86
Unit Pressure Drop kPa 36 56 67 93
Airflow m3/hr 28420 34685 40950 47375
No. of Fans No. 2 3 3 4
Fan Motor kW 3.6 2.8 3.6 2.8
EC Fan Diameter mm 630 630 630 630
Electric Reheat kW 25.0 25.0 25.0 25.0
No. of Steps No. 2 2 2 2
Humidifier Capacity kg/hr 8 8 8 8
Humidifier Power kW 5.8 5.8 5.8 5.8

4 ROW COIL - 15/20C

Model : Fan Under Floor 204 244 284 324

Air On: 30oC, 30% RH
Total Capacity kW 88.9 111.0 133.2 156.3
Sensible Capacity kW 88.9 111.0 133.2 156.3
Chilled Water Flow l/s 4.48 5.60 6.72 7.86
Unit Pressure Drop kPa 36 56 67 93
Air On: 32oC, 30% RH
Total Capacity kW 104.5 129.5 155.4 181.3
Sensible Capacity kW 104.5 129.5 155.4 181.3
Chilled Water Flow l/s 5.25 6.54 7.83 9.15
Unit Pressure Drop kPa 49 76 90 126
Airflow m3/hr 28420 34685 40950 47375
No. of Fans No. 2 3 3 4
Fan Motor kW 3.6 2.8 3.6 2.8
EC Fan Diameter mm 630 630 630 630
Electric Reheat kW 25.0 25.0 25.0 25.0
No. of Steps No. 2 2 2 2
Humidifier Capacity kg/hr 8 8 8 8
Humidifier Power kW 5.8 5.8 5.8 5.8

Notes:
1. Capacities are based on a 14oC / 15oC chilled water coil entering temperature & the tabulated flow rate.
2. For capacities at other conditions, please refer to the Factory or product selection program.

18
 CHILLED WATER COOLED UNITS - COOLING CAPACITIES 50/60Hz

6 ROW COIL - 16/22C

Model : Fan Under Floor 206 246 286 326

Air On: 30oC, 30% RH
Total Capacity kW 95.3 118.4 141.5 165.6
Sensible Capacity kW 95.3 118.4 141.5 165.6
Chilled Water Flow l/s 4.01 4.98 5.97 6.96
Unit Pressure Drop kPa 31 48 59 83
Air On: 32oC, 30% RH
Total Capacity kW 112.9 139.7 167.4 194.3
Sensible Capacity kW 112.9 139.7 167.4 194.3
Chilled Water Flow l/s 4.74 5.88 7.01 8.18
Unit Pressure Drop kPa 43 66 81 113
Airflow m3/hr 28420 34685 40950 47375
No. of Fans No. 2 3 3 4
Fan Motor kW 3.6 2.8 3.6 2.8
EC Fan Diameter mm 630 630 630 630
Electric Reheat kW 25.0 25.0 25.0 25.0
No. of Steps No. 2 2 2 2
Humidifier Capacity kg/hr 8 8 8 8
Humidifier Power kW 5.8 5.8 5.8 5.8

6 ROW COIL - 17/22C

Model : Fan Under Floor 206 246 286 326

Air On: 30oC, 30% RH
Total Capacity kW 91.2 112.9 135.1 157.3
Sensible Capacity kW 91.2 112.9 135.1 157.3
Chilled Water Flow l/s 4.60 5.70 6.82 7.94
Unit Pressure Drop kPa 40 63 76 107
Air On: 32oC, 30% RH
Total Capacity kW 108.2 134.1 160.0 183.2
Sensible Capacity kW 108.2 134.1 160.0 183.2
Chilled Water Flow l/s 5.47 6.77 8.06 8.4
Unit Pressure Drop kPa 55 87 106 119
Airflow m3/hr 28420 34685 40950 47375
No. of Fans No. 2 3 3 4
Fan Motor kW 3.6 2.8 3.6 2.8
EC Fan Diameter mm 630 630 630 630
Electric Reheat kW 25.0 25.0 25.0 25.0
No. of Steps No. 2 2 2 2
Humidifier Capacity kg/hr 8 8 8 8
Humidifier Power kW 5.8 5.8 5.8 5.8

Notes:
1. Capacities are based on a 16oC / 17oC chilled water coil entering temperature & the tabulated flow rate.
2. For capacities at other conditions, please refer to the Factory or product selection program.

19
 ELECTRICAL DETAILS
Air Cooled Models
Model 080 120 160 200 240 280
400V/3PH/50Hz
EC Fans FLA 4.1 4.2 4.9 4.2 4.2 4.2
Reheat FLA 13.9 21.7 35.9 35.9 35.9 35.9
Humidifier FLA 3.2 8.4 8.4 8.4 8.4 8.4
Scroll Compressor FLA 13.6 23.3 29 36.2 46.6 55.6
Condenser FLA 30°C 3.0 6.0 6.0 6.0 6.0 9.0
Condenser FLA 35°C 6.0 6.0 6.0 6.0 6.0 9.0
Condenser FLA 40°C 6.0 9.0 6.0 9.0 9.0 12.0
Condenser FLA 45°C 6.0 12.0 9.0 9.0 12.0 6.0
Condenser FLA 50°C 9.0 12.0 9.0 12.0 12.0 10.0
220V/3PH/60Hz
EC Fans FLA 7.5 7.6 8.9 7.6 7.6 7.6
Reheat FLA 25.2 39.4 65.6 65.6 65.6 65.6
Humidifier FLA 5.8 15.3 15.3 15.3 15.3 15.3
Scroll Compressor FLA 24.7 42.4 52.7 65.8 84.7 101.1
Condenser FLA 30°C 3.9 7.8 7.8 7.8 7.8 11.7
Condenser FLA 35°C 7.8 7.8 7.8 7.8 7.8 11.7
Condenser FLA 40°C 7.8 11.7 7.8 11.7 11.7 15.6
Condenser FLA 45°C 7.8 15.6 11.7 11.7 15.6 9.9
Condenser FLA 50°C 11.7 15.6 11.7 15.6 15.6 16.5
380V/3PH/60Hz
EC Fans FLA 4.3 4.4 5.1 4.4 4.4 4.4
Reheat FLA 13.2 20.6 34.3 34.3 34.3 34.3
Humidifier FLA 3.4 8.8 8.8 8.8 8.8 8.8
Scroll Compressor FLA 14.3 24.5 30.5 38.1 49.1 58.5
Condenser FLA 30°C 3.9 7.8 7.8 7.8 7.8 11.7
Condenser FLA 35°C 7.8 7.8 7.8 7.8 7.8 11.7
Condenser FLA 40°C 7.8 11.7 7.8 11.7 11.7 15.6
Condenser FLA 45°C 7.8 15.6 11.7 11.7 15.6 5.7
Condenser FLA 50°C 11.7 15.6 11.7 15.6 15.6 9.5
460V/3PH/60Hz
EC Fans FLA 3.6 3.7 4.3 3.7 3.7 3.7
Reheat FLA 15.9 24.9 41.5 41.5 41.5 41.5
Humidifier FLA 2.8 7.3 7.3 7.3 7.3 7.3
Scroll Compressor FLA 11.8 20.3 25.2 31.5 40.5 48.3
Condenser FLA 30°C 1.2 2.4 2.4 2.4 2.4 3.6
Condenser FLA 35°C 2.4 2.4 2.4 2.4 2.4 3.6
Condenser FLA 40°C 2.4 3.6 2.4 3.6 3.6 4.8
Condenser FLA 45°C 2.4 4.8 3.6 3.6 4.8 4.8
Condenser FLA 50°C 3.6 4.8 3.6 4.8 4.8 8.0
Notes:
1. FLA = Full Load Amps.
2. Unit maximum FLA is the total of the components, which operate during maximum electrical load conditions. For units with
humidifier & electric reheat the maximum FLA would be in dehumidification mode ie. cooling & reheat or in cooling and
humidification mode ie. cooling & humidifier.
3. In dehumidification mode, calculate the max FLA based on 1x compressor FLA as only 1x compressor operates in this mode.
4. In cooling and humidification mode, calculate the max FLA based on dual compressor FLA as both compressors and the
humidifier operate in this mode.
5. For all models 2 no. condensers are required, 1 per refrigerant circuit.
6. For compressor & condenser FLA, tabulated values are per component.

ELECTRICAL DETAILS
20
Chilled Water Models - Standard
Model 064/6 084/6 124/6 164/6 204/6 244/6 284/6 324/6
400V/3PH/50Hz
EC Fans FLA 2.4 4.1 5.5 9.8 8.4 12.6 12.6 16.8
Reheat FLA 13.9 13.9 21.7 35.9 35.9 35.9 35.9 35.9
Humidifier FLA 3.2 3.2 8.4 8.4 8.4 8.4 8.4 8.4
Max Unit FLA - Cool only 3.4 5.1 6.5 10.8 9.4 13.6 13.6 17.8
Max Unit FLA - Cool & Dehumidify 17.3 19.0 28.2 46.7 45.3 49.5 49.5 53.7
Max Unit FLA - Heat & Humidify 20.5 22.2 36.6 55.1 53.7 57.9 57.9 62.1
220V/3PH/60Hz
EC Fans FLA 4.4 7.5 10.0 17.8 15.2 22.8 22.8 30.4
Reheat FLA 19.7 25.2 39.4 65.6 65.6 65.6 65.6 65.6
Humidifier FLA 5.8 5.8 15.3 15.3 15.3 15.3 15.3 15.3
Max Unit FLA - Cool only 5.4 8.5 11.0 18.8 16.2 23.8 23.8 31.4
Max Unit FLA - Cool & Dehumidify 25.1 33.7 50.4 84.4 81.8 89.4 89.4 97.0
Max Unit FLA - Heat & Humidify 30.9 39.5 65.7 99.7 97.1 104.7 104.7 112.3
380V/3PH/60Hz
EC Fans FLA 2.5 4.3 5.8 10.2 8.8 13.2 13.2 17.6
Reheat FLA 10.3 13.2 20.6 34.3 34.3 34.3 34.3 34.3
Humidifier FLA 3.4 3.4 8.8 8.8 8.8 8.8 8.8 8.8
Max Unit FLA - Cool only 3.5 5.3 6.8 11.2 9.8 14.2 14.2 18.6
Max Unit FLA - Cool & Dehumidify 13.8 18.5 27.4 45.5 44.1 48.5 48.5 52.9
Max Unit FLA - Heat & Humidify 17.2 21.9 36.2 54.3 52.9 57.3 57.3 61.7
460V/3PH/60Hz
EC Fans FLA 2.1 3.6 4.8 8.6 7.4 11.1 11.1 14.8
Reheat FLA 12.4 15.9 24.9 41.5 41.5 41.5 41.5 41.5
Humidifier FLA 2.8 7.3 7.3 7.3 7.3 7.3 7.3 7.3
Max Unit FLA - Cool only 3.1 4.6 5.8 9.6 8.4 12.1 12.1 15.8
Max Unit FLA - Cool & Dehumidify 15.5 20.5 30.7 51.1 49.9 53.6 53.6 57.3
Max Unit FLA - Heat & Humidify 18.3 27.8 38.0 58.4 57.2 60.9 60.9 64.6

Notes:
1. FLA = Full Load Amps.
2. Unit maximum FLA is the total of the components, which operate during maximum electrical load conditions.
3. Max FLA of cooling only unit: FLA = Controls + Fans.
4. Max FLA of unit with reheat in dehumidification: FLA = Controls + Fans + Reheat.
5. Max FLA of unit with heating & humidifiers: FLA = Controls + Fans + Reheat + Humidifier.

21
 ELECTRICAL DETAILS
Chilled Water Models – Fan Under Floor
Model 204/6 244/6 284/6 324/6
400V/3PH/50Hz
EC Fans FLA 11.0 12.6 16.5 16.8
Reheat FLA 35.9 35.9 35.9 35.9
Humidifier FLA 8.4 8.4 8.4 8.4
Max Unit FLA - Cool only 12.0 13.6 17.5 17.8
Max Unit FLA - Cool & Dehumidify 47.9 49.5 53.4 53.7
Max Unit FLA - Heat & Humidify 56.3 57.9 61.8 62.1
220V/3PH/60Hz
EC Fans FLA 20.0 22.8 30.0 30.4
Reheat FLA 65.6 65.6 65.6 65.6
Humidifier FLA 15.3 15.3 15.3 15.3
Max Unit FLA - Cool only 21.0 23.8 31.0 31.4
Max Unit FLA - Cool & Dehumidify 86.6 89.4 96.6 97.0
Max Unit FLA - Heat & Humidify 101.9 104.7 111.9 112.3
380V/3PH/60Hz
EC Fans FLA 11.6 13.2 17.4 17.6
Reheat FLA 34.3 34.3 34.3 34.3
Humidifier FLA 8.8 8.8 8.8 8.8
Max Unit FLA - Cool only 12.6 14.2 18.4 18.6
Max Unit FLA - Cool & Dehumidify 46.9 48.5 52.7 52.9
Max Unit FLA - Heat & Humidify 55.7 57.3 61.5 61.7
460V/3PH/60Hz
EC Fans FLA 9.6 11.1 14.4 14.8
Reheat FLA 41.5 41.5 41.5 41.5
Humidifier FLA 7.3 7.3 7.3 7.3
Max Unit FLA - Cool only 10.6 12.1 15.4 15.8
Max Unit FLA - Cool & Dehumidify 52.1 53.6 56.9 57.3
Max Unit FLA - Heat & Humidify 59.4 60.9 64.2 64.6

Notes:
1. FLA = Full Load Amps.
2. Unit maximum FLA is the total of the components, which operate during maximum electrical load conditions.
3. Max FLA of cooling only unit: FLA = Controls + Fans.
4. Max FLA of unit with reheat in dehumidification: FLA = Controls + Fans + Reheat.
5. Max FLA of unit with heating & humidifiers: FLA = Controls + Fans + Reheat + Humidifier.

22