Scribd Logo
Upload

Welcome to Scribd!

  • 56 views

    Remanufacturing Instructions: Brother HL5240 (TN580)

    Uploaded by

    Ивайло Колев
    Remove the fill plug and dump remaining toner from the toner hopper. Remove the developer roller stabilizer from the developer roller. Clean all gears of residual toner to ensure smooth rotation.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd

    Remanufacturing Instructions: Brother HL5240 (TN580)

    Uploaded by

    Ивайло Колев
    56 views7 pages
    Remove the fill plug and dump remaining toner from the toner hopper. Remove the developer roller stabilizer from the developer roller. Clean all gears of residual toner to ensure smooth rotation.

    Original Title

    BROTHER 5250_TN580TN3170

    Copyright

    © Attribution Non-Commercial (BY-NC)

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Remove the fill plug and dump remaining toner from the toner hopper. Remove the developer roller stabilizer from the developer roller. Clean all gears of residual toner to ensure smooth rotation.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    56 views7 pages

    Remanufacturing Instructions: Brother HL5240 (TN580)

    Uploaded by

    Ивайло Колев
    Remove the fill plug and dump remaining toner from the toner hopper. Remove the developer roller stabilizer from the developer roller. Clean all gears of residual toner to ensure smooth rotation.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 7

    Remanufacturing Instructions

    Brother HL5240 (TN580)


    For Technical Support, please call Memphis, TN at (888) 757-0762 or Nashua, NH at (888) 833-5727.

    OEM Reference Information:


    Yield
    Toner: TN550 3500 @ 5%
    TN580 7000 @ 5%

    Drum: DR520 25000 @ 5%

    1. Remove the fill plug and dump remaining


    toner from the toner hopper (Fig. 1).

    Fig. 1

    2. Remove one screw from the end plate (Fig.


    2). Remove end plate.

    Fig. 2

    © 2007 Oasis Imaging Products, Inc. Page 1


    3. Using a small screw driver, release the
    locking pins on the developer roller stabilizer
    (Fig. 3).

    Fig. 3

    4. Remove the developer roller stabilizer from


    the developer roller (Fig. 4).

    Fig. 4

    5. Remove two screws from the end cap on the


    geared side of the cartridge (Fig. 5).

    Fig. 5

    © 2007 Oasis Imaging Products, Inc. Page 2


    6. Remove the end cap. The reset flag gear
    (Fig. 6) may come off with the end cap. Be
    careful not to lose the small spring (Fig. 6a)
    located behind the gear. This spring is needed
    to reset the flag gear.

    Fig. 6
    Fig. 6a

    7. Remove the black cap located on the


    developer roller post on the geared side of the
    cartridge (Fig. 7).

    Fig. 7

    8. Make a note of the gear positions.


    Assuming the flag gear is still in place, remove
    the five gears and the spring behind the flag
    gear (Fig. 8). Clean all gears of residual toner
    to ensure smooth rotation.

    Fig. 8

    © 2007 Oasis Imaging Products, Inc. Page 3


    9. Insert a small screwdriver between the
    locking tab and the cartridge housing and pry
    outward as shown (Fig. 9).

    Fig. 9

    10. Rotate the tab as shown (Fig. 10). This


    will release the locking tab from the
    cartridge housing.

    Fig. 10

    11. Remove the developer roller from the


    cartridge (Fig. 11). Grasp the roller by the
    end posts. Clean the roller with compressed
    air and a lint free, wax free wipe.

    Fig. 11

    © 2007 Oasis Imaging Products, Inc. Page 4


    12. Use compressed air and vacuum to clean
    all residual toner from the hopper. Clean the
    foam delivery roller, located behind the
    developer roller, thoroughly. Failure to do so
    can cause backgrounding. Clean the doctor
    blade with compressed air and a lint free
    cloth. Inspect the blade to ensure that no
    cloth fibers have adhered to the blade. Clean
    the developer roller sealing felts with
    compressed air (Fig. 12). Fig. 12

    13. Clean all components and gears


    thoroughly. Fill toner with proper gram load
    and reassemble in reverse order (Fig. 13).

    Fig. 13

    Fig. 14

    14. During reassembly the flag gear must be


    reset. Set the flag gear spring on the gear
    post (Fig.14). Set the small end of the spring
    on the slot on the gear post.

    © 2007 Oasis Imaging Products, Inc. Page 5


    Fig. 15

    15. Place the flag gear on the post and


    position the spring as shown (Fig. 15).

    16. Secure the end cap with two screws.


    Figure sixteen shows the correct position of
    the flag gear for resetting the printer (Fig.
    16).

    Fig. 16

    17. Install a developer roller cover for


    shipping (Fig. 17).

    Fig. 17

    © 2007 Oasis Imaging Products, Inc. Page 6


    Oasis and You … Succeeding Together!

    New Hampshire Tennessee Texas Canada South America


    (603) 880-3991 (901) 433-0334 (972) 671-1307 (905) 568-3422 (305) 383-2260
    (888) 627-6555 Fax: (901) 366-9756 (888) 591-3555 (800) 430-7886 Fax: (305) 383-2558
    Fax: (603) 598-4277 Fax: (972) 671-1359 Fax: (905) 568-3491

    Illinois California North Carolina Europe


    (630) 982-1543 (714) 283-6270 (919) 776-0847 Netherlands
    (888) 658-4555 (888) 656-9555 (866) 399-8558 011-31-24-388-2233
    Fax: (630) 928-1542 Fax: (714) 283-6276 Fax: (919) 776-0898 Fax: 011-31-24-355-7373

    © 2007 Oasis Imaging Products, Inc. Any attempt to reproduce any part of these instructions without the written consent of
    Oasis Imaging Products, Inc. may result in legal action. All registered trademarks are the property of their respective owners.

    © 2007 Oasis Imaging Products, Inc. Page 7

    You might also like