MX6 29000 MX7 15000 Rotary Cutters

Copyright 2007 (c) Deere & Company. THIS DATA IS THE PROPERTY OF DEERE &
COMPANY. ALL USE AND/OR REPRODUCTION NOT SPECIFICALLY
AUTHORIZED BY DEERE & COMPANY IS PROHIBITED.

All information, illustrations and specifications in this manual are based on the latest
information available at the time of publication. The right is reserved to make changes at
any time without notice.

Foreword
Dealer's Record
Predelivery
Delivery
After-Sale
Record Rotary Cutter Serial Number
Keep Proof of Ownership
Keep Machines Secure

Section : 05 - Safety

Recognize Safety Information

Understand Signal Words
Follow Safety Instructions
Protect Bystanders
Stay Clear of Rotating Blades
Operate Tractor and Cutter Safely
Back Up Safely
Leaving Cutter Unattended
Keep Riders Off Machine
Prepare for Emergencies
Wear Protective Clothing
Stay Clear of Rotating Drivelines
Transport Cutter Safely
Avoid Serious Injury or Death from Accidental Lowering of Cutter
Practice Safe Maintenance
Remove Paint Before Welding or Heating
Store Attachments Safely
Safety Features

Section : 10 - Safety Signs

Safety Signs-Drivelines
Safety Signs-Driveline Shield
Safety Signs-Hitch
Safety Signs-Deck

Section : 15 - Preparing the Tractor

Selecting Tractor Size

Positioning Tractor Drawbar
Selecting Tractor PTO Speed
Adjusting Tractor Hitch
Checking Ballast, Wheel Spacing, and Tire Inflation
Determining Front Ballast

Section : 20 - Preparing the Cutter

Prestarting Checklist
Preparing Hitch Pins
Installing Hitch Pin Bushings for Quick Coupler Hitch
Installing Category 2 Hitch Pin Conversion Kit (MX5 and MX6)

Section : 25 - Attaching and Detaching

Attaching Cutter to Tractor with Quick Coupler

Attaching Cutter to Tractor with Three-Point Hitch
Assembling Main PTO Driveline Telescoping Members (If Necessary)
Attaching PTO Driveline
Detaching Cutter From Tractor

Section : 30 - Transporting

Preparing Cutter For Transport

Follow Safe Transport Procedures
Making Turns
Keep Riders Off Machine

Section : 35 - Operating the Cutter

Preparing Cutter for Operation

Adjusting Cutting Height/Tailwheel Position
Keep Riders Off Machine
Follow Safe Operating Procedures
Operating the Cutter for Best Performance
Cutting Technique
Turning Cutter
Attachments Available

Section : 40 - Lubrication and Maintenance

Lubricating and Maintaining Machine Safely
Grease
Gear Case Oil
Alternative and Synthetic Lubricants
Mixing of Lubricants
Lubricant Storage
Perform Lubrication and Maintenance
Observe Lubrication Symbols
Every 8 Hours or Daily
Every 24 Hours
Every 50 Hours
Annually
As Required

Section : 45 - Service

Practice Safe Service Procedures

Keep Service Area Clean
Removing and Installing PTO Driveline-MX5 and MX6
Removing and Installing PTO Driveline-MX7
Disassembling and Inspecting Slip Clutch-MX5 and MX6
Disassembling and Inspecting Slip Clutch-MX7
Assembling Slip Clutch
Checking Blade Wear
Replacing Blades
Direction of Blade Rotation
Replacing Skid Shoes
Metric Bolt and Screw Torque Values
Unified Inch Bolt and Screw Torque Values

Section : 50 - Assembly

Perform Predelivery Service Safely

Installation Instructions Available Online to John Deere Dealers
Remove Shipping Dunnage and Parts
Check Blade Hardware Torque
Fill Gear Case
Install Front Safety Shield (Chain)
Install Rear Safety Shield (Chain)
Install Tailwheel-MX5 and MX6
Install Axle Support(s), Spindle(s) and Tailwheel(s)-MX7
Install Hitch
Install PTO Driveline-MX5 and MX6
Install PTO Driveline-MX7
Final Inspection and Adjustments
 Section : IBC - John Deere Service Keeps You On The Job

John Deere Is At Your Service

Selecting Tractor PTO Speed

IMPORTANT: Never operate a cutter

equipped for 540 rpm PTO drive with
a tractor equipped with 1000 rpm
PTO.

Always run tractor at rated PTO

speed. Overspeed will cause damage
to drive system.

Refer to your tractor Operator's Manual to

change PTO stub shaft, if necessary.

Determining Front Ballast

IMPORTANT: If the total implement code

CAUTION: To help prevent personal exceeds the maximum implement code
injury caused by loss of steering for your tractor, the
control, be sure tractor is equipped machine/attachment combination is
with proper amount of front ballast. not recommended.

John Deere engineers have developed an Model Code

implement code to determine how much front
ballast is needed on the tractor for stability MX5 59
and steering control. MX6 82
MX7 (single 119
The cutter is approved for use on tractors that tailwheel)
meet or exceed the implement codes. Tractor
MX7 (dual 130
stability is necessary for safe operation. (See
tailwheels)
your tractor Operator's manual for complete
ballasting information.)

Determine required ballast by using See your tractor Operator's Manual to

information in chart. determine amount of front ballast.

Implement Code Using Standard 3-Point Hitch

Number of 70 lb. (32 kg) Weights 4120 - 4720
0 48
1 51
2 55
3 58
4 61
5 65
6 68
7 71
8 74
9 79
10 83
11 86
12 88

Adjusting Tractor Hitch

Refer to tractor Operator's Manual to adjust • Lateral Float: Place lift link pins in
the following: the float position.
• Center Link: Place center link in
• Side Sway: Adjust sway chains or correct position for proper draft-
locks/blocks to minimize side sensing sensitivity.
movement at all hitch positions.
 • Rate of Drop: Allow at least two
seconds for machine to lower from
full height to ground.

Prestarting Checklist

Perform the following procedures before operating the cutter:

• Gear Case
o Check oil level. (See EVERY 8 HOURS OR DAILY in Lubrication and
Maintenance section.)
o Check hardware torque. (See EVERY 50 HOURS in Lubrication and
Maintenance section.)
o Remove any material wound on gear case shafts.
o Check oil seals for leakage.
• Blades and Blade Holder
o Inspect blades for wear or damage. (See CHECKING BLADE WEAR in
Service section.)
o Check blade hardware torque. (See REPLACING BLADES in the Service
section.)
o Check blade holder hardware torque. (See EVERY 50 HOURS in
Lubrication and Maintenance section.)
• Tailwheel
o Tighten tailwheel nuts. (See EVERY 24 HOURS in Lubrication and
Maintenance section.)
• Hitch Pins
o Check torque on hitch pin lock nuts. (See AS REQUIRED in Lubrication
and Maintenance section.)
• Driveline Shield
o Check if driveline shield spins freely. (See AS REQUIRED in Lubrication
and Maintenance section.)
• Lubricating the Cutter
o Lubricate cutter and drivelines. (See Lubrication and Maintenance
section.)

7. If cutter is being returned to service from storage, evenly tighten six lock nuts (A) on
slip clutch to apply spring load to clutch disks.

IMPORTANT: Slip clutch components must be free to rotate when necessary.

Clutch disks will seize if left unused for a period of time, especially in humid or
damp conditions. Linings may bond to metal parts causing slip clutch to be
ineffective, resulting in machine damage.
 8. If cutter has not been used for a while, free slip clutch disks and adjust spring load.
(See Freeing Slip Clutch procedure in AS REQUIRED in Lubrication and Maintenance
section.)

Attaching Cutter to Tractor with

Three-Point Hitch

CAUTION: To avoid bodily injury or

machine damage whenever an
implement is attached, put
transmission in PARK position and
check the full range of hitch for
interference, binding, or PTO
separation.

Do not stand between tractor and

implement.

NOTE: John Deere 4000 Series tractor

shown throughout procedure.
A-Tractor Center Link
1. Back up tractor to cutter with hitch points B-Tractor Draft Links
approximately in alignment.

2. Engage tractor parking brake and/or place

transmission in "Park".

3. Shut off tractor engine and remove key.

4. Remove center link mounting hardware

and hitch pin assemblies at both hitch masts.

5. Align tractor draft links (B) with hitch

masts and install hitch pin assemblies
according to tractor hitch category. (See
PREPARING HITCH PINS in Preparing the
Cutter section.)

6. Align center link (A) with cutter pivot

plate and install center link mounting
hardware.

7. Start tractor engine.

 AG,OUO1078,353 -19-28JAN00-1/2

8. Slowly pull hitch control lever (A) to raise

cutter. Check for interference. Lower hitch to
ground and adjust center link and/or lift links
if necessary. (See procedures in your tractor
Operator's manual.)

A-Hitch Control Lever

Detaching Cutter From Tractor

CAUTION: To prevent personal injury

caused by unexpected movement:
1. Park machine on a level surface.
2. Engage tractor parking brake and/or place
transmission in "Park".
3. Disengage PTO.
4. Shut off tractor engine and remove key.
1. Park cutter on a level surface.
2. Tractor with Quick Coupler Hitch:
Slowly push hitch control lever (A) to lower A-Hitch Control Lever
cutter close to the ground.
Tractor with Three-Point Hitch: Slowly
push hitch control lever (A) to lower cutter to
the ground.
3. Engage tractor parking brake and/or place
transmission in "Park".

Detaching Cutter From Tractor

CAUTION: To prevent personal

injury caused by unexpected
movement:

1. Park machine on a level surface.

2. Engage tractor parking
brake and/or place
transmission in "Park". A-Hitch Control Lever
3. Disengage PTO.
4. Shut off tractor engine and
 remove key.

1. Park cutter on a level surface.

2. Tractor with Quick Coupler Hitch:

Slowly push hitch control lever
(A) to lower cutter close to the
ground.

Tractor with Three-Point Hitch:

Slowly push hitch control lever
(A) to lower cutter to the
ground.

3. Engage tractor parking brake

and/or place transmission in
"Park".
Removing and Installing PTO
Driveline-MX5 and MX6

1. Disconnect chain (C).

2. Remove two quick-lock pins (B) and raise

PTO shield (A).

A-PTO Shield
B-Quick-Lock Pin (2 used)
C-Chain
AG,OUO1078,363 -19-23AUG07-1/2
NOTE: Driveline removed for illustration
purposes.

3. Pull locking collar (A) toward slip clutch.

4. Remove driveline assembly from gear

case input shaft.

5. Make repairs as necessary:

• Slip clutch service-See

DISASSEMBLING AND
INSPECTING SLIP CLUTCH-MX5
AND MX6 in this section.
• Driveline repair-See your John Deere
dealer.

IMPORTANT: Apply multipurpose

grease on gear case input shaft.

6. Install driveline in reverse order of

removal.

A-Locking Collar

Adjusting Cutting Height/Tailwheel

Position

1. Position machine on flat level ground.

2. Raise cutter.
AG,OUO1078,340 -19-24AUG07-1/7

CAUTION: Be sure to support cutter

frame at all four corner locations with
safety shop stands to prevent
accidental lowering. Do not position
safety stands under axle or wheel
supports because these components
can rotate.

3. Place safety shop stands under cutter.

4. Lower cutter onto stands.
AG,OUO1078,340 -19-24AUG07-2/7

5. Wrap a lifting strap around axle support

tube and attach to a hoist.

AG,OUO1078,340 -19-24AUG07-3/7

A-Cap Screw and Lock B-Cap Screw and Lock C-Cap Screw and Lock
Nut Nut Nut (2 used)
6. Loosen lock nut and cap screw (B). NOTE: MX7: Repeat steps (5-10) on second
tailwheel (if equipped).
7. Loosen two cap screws and lock nuts (C).
11. Raise cutter and remove safety stands.
8. Remove lock nut and cap screw (A).
12. Using rock shaft control lever, lower
9. Raise or lower axle support tube to desired cutter until skid shoe is parallel to ground and
cutting height position. rear wheel makes contact with ground.
10. Re-install cap screw and lock nut (A).
Tighten all lock nuts.
AG,OUO1078,340 -19-24AUG07-4/7

13. Adjust depth stop (A). (See your tractor

Operator's Manual.)

A-Depth Stop

AG,OUO1078,340 -19-24AUG07-5/7

NOTE: The tailwheel supports the rear of the

machine and the draft links support the
front to allow the cutter to follow the
ground contour.

14. Adjust center link to take all slack out of

connection.

AG,OUO1078,340 -19-24AUG07-6/7

IMPORTANT: Loosening the center link

may allow the driveline to contact the
cutter frame or tractor tires to contact
the chain shield. Raise the cutter
slowly and check for interference.
Lengthen tractor lift links to provide
clearance to full height.

NOTE: Lift height may also be limited by

installing stops on rockshaft control
lever bracket.
A-Distance
15. Lengthen center link so distance (A) is B-Links
according to specifications, allowing links
(B) to swing free. This allows the rear of
cutter to float over obstructions.

Specification

Center Link -Distance 12 mm (1/2 in.)

 Operating the Cutter for Best Performance

• Operate the cutter at full PTO rated speed.

• Slower ground speeds, less than 8 km/h (5 mph), will result in better cut quality.
• For best results, cutting height should be as low as possible (less than 100 mm [4
in.]).
• For most conditions, adjust the cutter so that skid (wear) shoes are parallel to the
ground.
• Blades must be sharp. Be sure suction blades are installed for the correct rotation.
(See REPLACING BLADES in the Service section.)

Cutting Technique

Adjust tractor rear tread so inside dimension

between tires is equal to width of cutter. If
this width is not possible, set tread to
maximum width.

Due to direction of blade rotation, the cutter

should be operated with uncut portion to the
right-hand side. This allows grass knocked
down by tractor tires on previous cut to be
picked up and cut on next pass.

A-Downed Grass (Previous Cut)

B-Blade Rotation
C-Tractor Tires (Uncut Material on
Right)

Turning Cutter

IMPORTANT: To help prevent damage

to side skirts or tailwheel(s), raise
cutter when turning if headland is
rough or uneven.

Avoid hitting objects such as trees or

fences, the cutter makes a large arc
when turning. Reduce ground speed.

It is not necessary to raise the cutter when

turning if ground speed is reduced and
headland is flat.

Grease

Use grease based on NLGI consistency

numbers and the expected air temperature
range during the service interval.

John Deere SD POLYUREA GREASE is

preferred.

The following greases are also recommended

• John Deere HD LITHIUM

COMPLEX GREASE
• John Deere HD WATER
RESISTANT GREASE
• John Deere GREASE-GARD ™

Other greases may be used if they meet the

following:

NLGI Performance Classification GC-LB

IMPORTANT: Some types of grease

thickeners are not compatible with
others. Consult your grease supplier
before mixing different types of grease.
Gear Case Oil

Use oil viscosity based on the expected air

temperature range during the period between
oil changes.

The following oils are preferred:

• John Deere GL-5 GEAR

LUBRICANT
• John Deere EXTREME-GARD ™

Other oils may be used if they meet API

Service Classification GL-5.

Every 8 Hours or Daily

Keeping Cutter Clean

IMPORTANT: Avoid machine damage

due to build up of debris, if any, on
cutter deck. Clean cuttings from deck
DAILY or more often if necessary.

Build up of material may interfere with

driveline, cause overheating of gear case
resulting in component damage or cause deck
to be corroded due to moisture in material.
OUMX005,0001E9F -19-24AUG07-1/4
Driveline-to-Gear Case Driveline-to-Tractor
End End
PTO Driveline
OUMX005,0001E9F -19-24AUG07-2/4

Tailwheel Bearings

OUMX005,0001E9F -19-24AUG07-3/4

Checking Gear Case Oil Level

CAUTION: Before servicing machine

refer to LUBRICATING AND
MAINTAINING MACHINE
SAFELY at the beginning of this
section.

Remove dipstick/vent (A). Oil level should

be between lines (B). Add John Deere GL-5
GEAR LUBRICANT, or equivalent, if
necessary.

Install dipstick/vent.

A-Dipstick/Vent
B-Lines

Every 24 Hours

Checking Tailwheel Nut Torque

Tighten tailwheel hardware to specifications.

Specification

Tailwheel Nuts -Torque 110 N·m (80 lb-ft)

 Every 50 Hours

MX5 and MX6

MX7
Tailwheel Spindle(s)
OUO6038,0001965 -19-18SEP07-1/4

Tightening Gear Case Mounting

Hardware

CAUTION: Before servicing machine

refer to LUBRICATING AND
MAINTAINING MACHINE
SAFELY at the beginning of this
section.

IMPORTANT: To help prevent structural

damage caused by loose hardware, A-Wrench
tighten gear case hardware as B-Torque Wrench
specified. Check torque after first 8
hours of use and every 50 hours
thereafter.

NOTE: Use an assistant to aid in tightening

procedure.

Access holes are provided in bottom of

blade holder pan. Manually rotate blade
holder to align holes with gear case
mounting hardware.

Tighten gear case mounting hardware to

specifications using a wrench (A), torque
wrench (B) and a torque multiplier if
necessary.

Specification

Gear Case Mounting

Hardware -Torque 350 N·m (258 lb-ft)
OUO6038,0001965 -19-18SEP07-2/4

Tightening Blade Holder Hardware

Before servicing machine refer to

LUBRICATING AND MAINTAINING
MACHINE SAFELY at the beginning of this
section.

IMPORTANT: Operating with a loose

blade holder can cause damage to the
splined connection. To ensure proper
seating between the blade holder and
output shaft, two initial tightenings
are required. Retighten after one hour
and again after the first day of
operation. In severe cutting
conditions, recheck torque every 50
hours.

1. Remove and discard existing cotter pin.

2. Make sure washer (F) and M30 nut (G)

are installed as shown. Tighten nut to
specification using a torque wrench (C), A-Piece of Pipe
torque multiplier (B) and a long piece of pipe B-Torque Multiplier
(A). Position pipe into a corner of the C-Torque Wrench
machine. D-Hole
E-Cotter Pin
Specification F-Washer, 31 x 56 x 6
G-Nut, M30
Nut -Torque 610 N·m (450 lb-ft)

NOTE: Make sure slots in nut (G) are

aligned with hole (D) in shaft after
tightening to specified torque. If
necessary, tighten nut slightly more to
align slots with hole.
3. Install NEW cotter pin (E).
OUO6038,0001965 -19-18SEP07-3/4

Check Blade Hardware Torque

CAUTION: Before servicing machine

refer to LUBRICATING AND
MAINTAINING MACHINE
SAFELY at the beginning of this
section.

Manually rotate driveline to align each lock

nut (A) with access hole in top of deck. Position to Tighten
Position torque multiplier, as shown.

Tighten lock nuts (A) according to

specification.

Specification

Lock Nut -Torque 850 N·m (627 lb-ft)

A-Lock Nuts

Annually

Driveline Inner Shaft

NOTE: Do not grease outer or inner plastic

shields.

Separate front and rear driveline, brush John

Deere SD POLYUREA Grease or equivalent
SAE multipurpose grease onto male section
of steel shaft, and reassemble.

Checking Blade Wear

IMPORTANT: Operating with blades that are not alike will cause vibration.
Always replace worn or broken blades in pairs. Never replace a single blade.

Check blades regularly for wear or breakage.

As Required

Checking Driveline Shields

CAUTION: Before servicing machine

refer to LUBRICATING AND
MAINTAINING MACHINE
SAFELY at the beginning of this
section.

To help prevent bodily injury or death

from entanglement in rotating
drivelines, replace any missing or
damaged shielding. Never operate
machine without shielding.

Check driveline shields by making sure they

rotate freely. Lubricate or replace if
necessary. (See your John Deere dealer.)
OUO6038,0001966 -19-12SEP07-1/5

Checking Hitch Pin Torque

1. Check hitch pin lock nuts (A) periodically
to be sure they are tight.

2. Tighten to specification.

Specification

Hitch Pin Lock Nut

-Torque 350 N·m (258 lb-ft)

A-Lock Nuts
OUO6038,0001966 -19-12SEP07-2/5

Freeing Slip Clutch

CAUTION: Help prevent bodily

injury or death caused by unexpected
tractor movement or entanglement in
rotating driveline.

• Disengage PTO.
 • Engage parking brake or
place transmission in PARK.
• Shut off tractor engine and
remove key.

IMPORTANT: Friction type clutches will

seize if left unused for a period of
time, especially in humid or damp
conditions. Slip the clutch using the
following procedure.

Perform the following steps using the tractor

that will operate cutter. (See attaching
procedures in Attaching and Detaching
section.)

1. Remove two quick lock pins (B) and raise

PTO shield (A).

A-PTO Shield
B-Quick Lock Pin (1 each side)
OUO6038,0001966 -19-12SEP07-3/5

NOTE: Drivelines removed for illustration

purposes.

2. Loosen six lock nuts (A) progressively

leaving some tension on belleville spring.

3. Place chalk mark (B) across belleville

spring and hub.

CAUTION: Help prevent personal MX5 and MX6

injury to bystanders from thrown
objects. Be sure no one is near the
cutter when adjusting.

4. Start tractor and run at low rpm. Check

clutch slippage:

a. Engage PTO for 2-3 seconds to slip the

clutch.

b. Disengage the PTO.

 c. Repeat Steps a and
b at least three times.
MX7
d. Disengage PTO,
shut off tractor
engine, remove key A-Lock Nut (6 used)
and allow B-Chalk Marks
components to stop
rotating.
OUO6038,0001966 -19-12SEP07-4/5

e. Check alignment of chalk marks (E):

If marks are still aligned, clutch DID

NOT slip: Disassemble and inspect for
wear or damage. (See DISASSEMBLING
AND INSPECTING SLIP CLUTCH in
Service section.)

If marks are not aligned, clutch has

slipped:
MX5 and MX6
IMPORTANT: To avoid driveline
damage, DO NOT overtighten lock
nuts. A gap must be left between
clutch plate (B) and belleville spring
(C).

1. Tighten six lock nuts (D) to apply spring

pressure to clutch disks.
2. Measure gap (A) between clutch plate (B)
and belleville spring (C). If gap is not within
specification, evenly adjust six lock nuts
until gap is to specification. MX5 and MX6
Clutch Plate-to-Spring
MX7
Gap (A) 4 mm (0.157 in.) MX7 Clutch Plate-
to-Spring
Gap (A) 3.5 mm (0.138 in.)
A-Gap
B-Clutch Plate
C-Belleville Spring
D-Lock Nut (6 used)
CAUTION: To help prevent bodily
E-C
injury or death from entanglement in
rotating drivelines, replace all
shielding removed and replace any
missing or damaged shielding. Never
 operate machine without shielding.

5. Close and fasten PTO shield.

Disassembling and Inspecting Slip Clutch-MX5 and MX6

1. Remove PTO driveline. (See procedure in this section.)

NOTE: Parts (A-F) are replaced as a kit.

2. Remove locking collar assembly as follows:

a. Pull back on locking collar (D).

b. Remove snap ring (F).

c. Remove parts (A-E).

A-Ring
B-Compression Spring
C-Ball (3 used)
D-Locking Collar
E-Ring
F-Snap Ring

Assembling Slip Clutch

Assemble slip clutch in reverse order of

disassembly using the following instructions:

• Install belleville spring (C) with

concave side facing away from yoke
end.

IMPORTANT: To avoid driveline

damage, DO NOT overtighten
cap screws and lock nuts. A
gap must be left between clutch
plate (B) and belleville spring
(C).

• Tighten cap screws and lock nuts (D)

leaving a gap (A) between clutch
 plate (B) and spring (C) according to MX5 and MX6 Clutch
specifications.

Specification

MX5 and MX6 Clutch

Plate-to-Spring -Gap 4 mm (0.157 in.)
MX7 Clutch Plate-to-
Spring -Gap 3.5 mm (0.138 in.)

A-Gap
B-Clutch Plate
C-Belleville Spring
D-Cap Screw and Lock Nut (6 used)

Replacing Blades

IMPORTANT: Operating with loose

blade hardware will damage the blade
holder and blades. Whenever the
blades have been removed or
replaced, blade hardware MUST also
be replaced. Always use genuine John
Deere parts. Check blade hardware
torque after one hour of operation and
every 50 hours thereafter. Position to Loosen

NOTE: Suction blades have cutting edge on

one side only. Note blade rotation when
installing blades. (See DIRECTION OF
BLADE ROTATION in this section.)

Manually rotate driveline to align each lock

nut with access hole in top of deck. Position
torque wrench and torque multiplier, as
shown, to loosen blade hardware. Discard
blade and mounting hardware.
OUO6038,000196A -19-19SEP07-1/2
Install new blade and mounting hardware
(A-D) as shown. Tighten lock nut (A) to
specification using torque wrench and torque
multiplier positioned as shown.

Specification

Blade Hardware
-Torque 850 N·m (627 lb-ft)

Position to Tighten
A-Lock Nut
B-Washer
C-Blade
D-Blade Bolt

Direction of Blade Rotation

IMPORTANT: Cutter shown is viewed

from the top. Take special note of
blade rotation shown by the arrow.

NOTE: MX7 with dual tailwheel assembly

shown.

Replacing Skid Shoes

CAUTION: When servicing skid

shoes, it will be necessary to work
underneath cutter. Before servicing
cutter, refer to PRACTICE SAFE
SERVICE PROCEDURES at the
 beginning of this section.

Avoid potentially toxic fumes and

dust. Hazardous fumes can be
generated when paint is heated by
welding, soldering, grinding, or using
a torch. Refer to REMOVE PAINT
BEFORE WELDING OR HEATING
in Safety section.
Skid Shoe-Right-Hand Side Shown
1. Lower cutter onto safety shop stands.

NOTE: Skid shoes (A) are welded on. A-Skid Shoe

2. Remove existing skid shoe with a grinder.

3. Weld on a new skid shoe.

4. Paint all exposed areas.

5. Raise cutter and remove safety stands.

6. Lower cutter to the ground.

Check Blade Hardware Torque

Manually rotate driveline to align each lock

nut (A) with access hole in top of deck.
Position torque multiplier, as shown.

Tighten lock nuts (A) according to

specification.

Specification
Position to Tighten
Lock Nut -Torque 850 N·m (627 lb-ft)

A-Lock Nuts
Fill Gear Case

IMPORTANT: Cutter is shipped without

gear case lubricant. DO NOT operate
the cutter without filling gear case
with specified amount of lubricant
listed below, or gear case will be
damaged.

1. Remove and discard shipping plug in top

of gear case.

2. Fill gear case according to initial fill

specifications with John Deere GL-5 GEAR
LUBRICANT, or equivalent. (See
Lubrication and Maintenance section.)

Specification

Gear Case -Capacity 2.7 L (3.0 U.S. qt)

A-Dipstick/Vent
IMPORTANT: Oil will move into lower B-Lines
cavity of gear case during initial
operation. Check oil level after 30
minute break-in period, and every 8
hours, or daily, thereafter.

3. Install dipstick/vent (A) and screw in

fully, then remove. Oil level should be
between lines (B). Add oil, as necessary.

4. Install dipstick/vent.
Install Front Safety Shield (Chain)

A-Shield Assembly B-Cap Screw, M12 x C-Washer, 13 x 24 x D-Lock Nut, M12

30 2.5 mm MX5-(5 used)
MX5-(5 used) MX5-(5 used) MX6-(7 used)
MX6-(7 used) MX6-(7 used) MX7-(9 used)
MX7-(9 used) MX7-(9 used)
Tighten all mounting hardware AFTER
shield assembly is installed.

Install Rear Safety Shield (Chain)

 MX5 Shown (Left-Hand Side)

A-Lock Nut, M12 (6 C-Support E-Cap Screw, M12 x F-Spacer (3 used)

used) D-Cap Screw, M12 x 150 (3 used) G-Shield Assembly
B-Washer, 13 x 24 x 25 (3 used)
2.5 mm (6 used)
Tighten all mounting hardware AFTER all
shields have been installed.
Install Tailwheel-MX5 and MX6

1. Wrap a lifting strap around axle support

tube and attach to a hoist.

2. Install tailwheel using M16 x 180 cap

screw, 16.26 x 25.4 x 137 mm spacer and
M16 lock nut (A). Tighten lock nut to
specifications.

Specification

Tailwheel Lock Nut

-Torque 240 N·m (177 lb-ft)

3. Lower tailwheel and remove lifting strap.

A-Lock Nut

Removing and Installing PTO

Driveline-MX5 and MX6

1. Disconnect chain (C).

2. Remove two quick-lock pins (B) and raise

PTO shield (A).

A-PTO Shield
B-Quick-Lock Pin (2 used)
C-Chain
AG,OUO1078,363 -19-23AUG07-1/2
NOTE: Driveline removed for illustration
purposes.

3. Pull locking collar (A) toward slip clutch.

4. Remove driveline assembly from gear

case input shaft.

5. Make repairs as necessary:

• Slip clutch service-See

DISASSEMBLING AND
INSPECTING SLIP CLUTCH-MX5
AND MX6 in this section.
• Driveline repair-See your John Deere
dealer.

IMPORTANT: Apply multipurpose

grease on gear case input shaft.

6. Install driveline in reverse order of

removal.

A-Locking Collar

Final Inspection and Adjustments

IMPORTANT: Blade hardware MUST be checked after the first hour and every 50
hours thereafter.

Check blade hardware torque. Re-tighten hardware after one hour of operation and every
50 hours thereafter. (See EVERY 50 HOURS, TIGHTENING BLADE HARDWARE in
Lubrication and Maintenance section.)