KEY INTERLOCK CABLE

< SERVICE INFORMATION >

KEY INTERLOCK CABLE
A
Removal and Installation INFOID:0000000005928277

COMPONENTS B

AT

WCIA0621E
K
1. Key interlock cable 2. Key cylinder 3. A/T shift selector assembly
A. Lock plate B. Holder C. Clip
L
D. Slider E. Key interlock rod F. Adjust holder
G. Casing cap

REMOVAL M
CAUTION:
Make sure that parking brake is applied before removal and installation.
1. Place the shift selector in the “N” position. N
2. Remove the shift selector handle. Refer to AT-216, "Shift Selector Handle Removal and Installation".
3. Remove the center console assembly. Refer to IP-11.
4. Slide the slider (A) toward the casing cap (B) while pressing tabs O
(C) on the slider to separate the slider (A) from the adjust holder
(D).
5. Remove the casing cap (B) from the cable bracket on the A/T P
shift selector assembly.
6. Remove the key interlock cable from the key interlock rod (E).

SCIA6975E

Revision: May 2010 AT-219 2011 Versa

 KEY INTERLOCK CABLE
< SERVICE INFORMATION >
7. Remove steering column cover (upper and lower) and instru-
ment lower finisher. Refer to IP-11.
8. Pull out the lock plate (A) from the holder (B).
9. Remove the key interlock cable (1) from the key cylinder (2).

SCIA6976E

10. Remove the clip (A), and then remove the key interlock cable
(1).

SCIA6973E

INSTALLATION
CAUTION:
• Install key interlock cable in such a way that it will not be damaged by sharp bends, twists or interfer-
ence with adjacent parts.
• After installing key interlock cable to A/T shift selector assembly, make sure that casing cap and
bracket are firmly secured in their positions.
1. Place the shift selector in the “P” position.
2. Turn ignition switch to “ACC” or “ON” position.
3. Set the key interlock cable (1) to the key cylinder (2).
4. Install the lock plate (A) to the holder (B).
5. Turn ignition switch to “LOCK” position.

SCIA6976E

6. Temporarily install the adjust holder (A) to the key interlock rod
(B).
7. Install the casing cap (C) to the cable bracket (D) on the A/T shift
selector assembly.
CAUTION:
• Do not bend or twist key interlock cable excessively when
installing.
• After installing key interlock cable to cable bracket (D) on
A/T shift selector assembly, make sure casing cap (C) is
firmly secured in cable bracket (D) on A/T shift selector
assembly. SCIA6188E
• If casing cap (C) is loose [less than 39.2 N (4.0 kg, 8.8 lb)
removing force], replace key interlock cable.

Revision: May 2010 AT-220 2011 Versa

 KEY INTERLOCK CABLE
< SERVICE INFORMATION >
8. Slide the slider (A) toward the key interlock rod (D) while press-
ing the pull lock (B) down to securely connect the adjust holder A
(C) with the key interlock rod (D).
CAUTION:
• Do not press tabs when holding slider (A).
B
• Do not apply any side to side force to key interlock rod (D)
when sliding slider (A).

AT

G
SCIA6978E

9. Secure the key interlock cable (1) with the clip (A).
H
10. Install steering column cover (upper and lower) and instrument
lower finisher. Refer to IP-11.
11. Install the center console assembly. Refer to IP-11.
I
12. Install the shift selector handle. Refer to AT-216, "Shift Selector
Handle Removal and Installation".
13. Check shift lock system. Refer to AT-206, "Description".
J

SCIA6973E
K

Revision: May 2010 AT-221 2011 Versa