Instructions for Installation

VisoOpt
01 Contents
01 Contents 11

02 Base Terminal
01 Base terminal VO-BT 06
02 Base terminal VO-BT (-B Version) 03

03 Extension Terminal
01 Extension terminal VO-ZT 04
02 Extension terminal VO-ZT (-B Version) 04

04 Cross- linking
01 Cross- linking of VO-BT and VO-ZT units 04

05 Buttons
01 Connection of buttons 05
02 Radio Receiver 12 pin 05
03 Connection device SVM-K 03
04 Radio Receiver in-wall 03
05 Radio Receiver 6 pin 03
06 Third party call buttons 01

Dok.-Nr.: SUP-VOP001 Date Version

Created by: Albrechtsberger
04.04.06 11
Contents Checked by: Pecha

VisoOpt Kapitel Seite

Schrack Seconet 01 01
 NB: T-GND is the earth connection for the buttons and cannot be used for
supplying current to the button (e.g. SVM-K)

VO-BT
P1 Resistors - see jumper 1
15k
T-GND

RA1

RA2
BL1

BL2
RF-A ZA2
RF-R ZA1 to next unit

relay outputs
max. RF-W ZE2

ON
1 2 3 4 5 6 7 8
30V/1A ST-A ZE1 15k
ST-R J5
ST-W 15k +

Current converter
+24V +

BE1

BA1

RA4

RA3
BE2

BA2

BL4

BL3
rt sw
-
4A -
Tr

Relays:

A = Make contact
R = Break contact
W = Common connector up 24V AC/DC
Call button RT

RF = Call relay
ST = Fault relay
(no fault = make contact closed)
+
BL
R

Lamp Lv1
(max 10 W)

up
If there are serveral buttons
Call button RT

connected in series, all resistors in

the buttons (apart from the last
one) should be disconnected at
one end. +
BL
R
R

The LEDs on the cancelbuttons can not be called.

Combined call cancel buttons (RAT) can not be used!

P1 Potentiometer for the volume-control

Cancel button AT

up
Jumper 5: Call circuit monitoring
Open Call circuit monitored. Do not disconnect the
A terminating resistor in the final call button (all
BL inputs that are not being used must be closed
+ using a 15k Ohms resistor)

Closed Call circuit not monitored. Also remove

terminating resistor in the last call button.

Attention: the connecting terminal for the acknowledgement-button If the jumper is not present in the version supplied,
is to be connected to T-GND. then the jumper is presumed as being closed.
This is allowed for the combination with VisoOpt only!
Switch Switch
1 2 3 OFF In the event of a call not being acknowledged,
OFF OFF Acoustic signal emitter off another signal will follow after 2 minutes
OFF ON Sound sequence 2: 2 secs 1000Hz sound, 2 secs mute ON Acoustic cancellation signal no longer activated
ON OFF Sound sequence 1: 2 secs 1000Hz sound, 16 secs mute 4 OFF Call cancellation from control panel possible
ON ON Sound sequence 3: ½ second 800 Hz sound, ON Call cancellation only possible from cancel button
½ second 1000 Hz sound 5 Connection to additional VO-BT unit activated
1/2seconds 1333Hz sound, 2 seconds mute 6 Connection to additional VO-ZT unit activated
7 reserved
8 reserved
Dok.-Nr.: SUP-VOP001 Date Version

Base terminal VO-BT Created by: Albrechtsberger

Checked by: Pecha
04.04.06 06
(FC008950- - oder FC008950-A, FC008960- - oder FC008960-A)
VisoOpt Kapitel Seite

Schrack Seconet 02 01
 NB: T-GND is the earth connection for the buttons and cannot be used fo Remove Jumper (1-4) if the input is
supplying curren to the button (e.g. SVM-K)
occupied.

Jumper Input
1 Input RA1

VO-BT
2 Input RA2
P1 3 Input RA3
T-GND 4 Input RA4

RA1

RA2
BL1

BL2
RF-A ZA2
RF-R ZA1 to next unit

relay outputs
max. RF-W ZE2

ON
1 2 3 4 5 6 7 8
30V/1A ST-A ZE1
ST-R 4 1 3 2
ST-W +

Current converter
+24V +

BE1

BA1

RA4

RA3
BE2

BA2

BL4

BL3
rt sw
-
4A -
Tr

Relays

A = Make contact
R = Break contact
24V AC/DC
W = Common connector up
Call button RT

RF = Call relay
ST = Fault relay
(No fault = make contact closed)
+
BL
R

Lamp LV1
(max 10 W)

up
If there are serveral buttons
Call button RT

connected in series, all resistors in

the buttons (apart from the last
one) should be disconnected at
one end. +
BL
R
R

The LEDs on the cancelbuttons can not be called.

Combined call cancel buttons (RAT) can not be used!

P1 Potentiometer for the volume-control

Cancel button AT

up
Jumper Call circuit monitoring
Open Call circuit monitored. Do not disconnect the
A terminating resistor in the final call button.
BL
+
Closed Call circuit not monitored. Also remove
terminating resistor in the last call button.

Attention: the connecting terminal for the acknowledgement-button

is to be connected to T-GND.
This is allowed for the combination with VisoOpt only!
Switch Switch
1 2 3 OFF In the event of a call not being acknowledged
OFF OFF Acoustic signal emitter off another signal will follow after 2 minutes
OFF ON Sound sequence 2: 2 secs 1000 Hz sound, 2 secs mute ON Acoustic cancellation signal no llonger activated
ON OFF Sound sequence 1: 2 secs 1000 Hz sound, 16 secs mute 4 OFF Call cancellation from control panel possible
ON ON Sound sequence 3: ½ second 800 Hz sound, ½ second ON Call cancellation only possible from cancel button
1000 Hz sound, ½ second 1333 Hz sound, 2 secs mute 5 Connection to additional VO-BT unit activated
6 Connection to additional VO-ZT unit activated
7 reserved
8 reserved
Dok.-Nr.: SUP-VOP001 Date Version

Base terminal VO-BT (-B Version) Created by: Albrechtsberger

Checked by: Pecha
04.04.06 03
(FC008950-B oder FC008960-B)
VisoOpt Kapitel Seite

Schrack Seconet 02 02
 NB: T-GND is the earth connection for the buttons and cannot be used for
supplying current to the buttons (e.g. SVM-K)!

Resistors
+ 24 V see jumper 3

15k 15k
T-GND

RA4

RA6
RA3

RA5
BL4

BL6
BL3

BL5
ZA2
ZA1 to next unit
ZE2
VO-ZT

ZE1 J9

J10 J11
+

Current converter
+24V
RA1

RA8

RA7
+
RA2

BL1

BL8

BL7
BL2

rt sw
15k 15k -
4A
Tr -

If there are serveral buttons

connected in series, all resistors in 24V AC/DC
the buttons (apart from the last
one) should be disconnected at
one end.
up
Call button RT

+
BL
R

Lamp LV1
(max 10 W)

up
Call button RT

+
BL
R
R

The LEDs on the cancelbuttons can not be called.

Cancel button AT

up Combined call cancel buttons (RAT) can not be used!

A
BL Jumper 10 and 11: reserve
+
Jumper 9: Call circuit monitoring
Open Call circuit monitored. Do not disconnect the
terminating resitor in the final call button (all
inputs that are not being used must be closed
using 15k Ohms resistor)
Attention: the connecting terminal for the acknowledgement-button
Closed Call circuit not monitored. Also remove
is to be connected to T-GND. terminating resistor in the last call button.
This is allowed for the combination with VisoOpt only!

Dok.-Nr.: SUP-VOP001 Date Version

Extension terminal VO-ZT Created by: Albrechtsberger

Checked by: Pecha
04.04.06 04
(FC008951-- oder FC008951-A)
VisoOpt Kapitel Seite

Schrack Seconet 03 01
 Remove Jumper (1-8) if the input
is occupied.
NB: T-GND is the earth connection for the buttons and cannot be used for
supplying current to the buttons (e.g. SVM-K)!
Jumper Input
1 Input RA1
2 Input RA2
3 Input RA3
4 Input RA4
Resistors 5 Input RA5
see jumper 3 6 Input RA6
7 Input RA7
8 Input RA8
T-GND

RA4

RA6
RA3

RA5
BL4

BL6
BL3

BL5
ZA2
ZA1 to next unit
ZE2
VO-ZT

ZE1
J2 J3 J4 J1 J8 J5 J6 J7

J10 J11
+

Current converter
+24V
RA1

RA8

RA7
+
RA2

BL1

BL8

BL7
BL2

rt sw
-
4A
Tr -

If there are serveral buttons

connected in series, all resistors in 24V AC/DC
the buttons (apart from the last
one) should be disconnected at
one end.
up
Call button RT

+
BL
R

Lamp LV1
(max 10 W)

up
Call button RT

+
BL
R
R

The LEDs on the cancelbuttons can not be called.

Cancel button AT

up Combined call cancel buttons (RAT) can not be used!

A
BL Jumper 10 and 11: reserve
+
Jumper 1 to 8: Call circuit monitoring
Open Call circuit monitored. Do not disconnect the
terminating resitor in the final call button

Attention: the connecting terminal for the acknowledgement-button

Closed Call circuit not monitored. Also remove
is to be connected to T-GND. terminating resistor in the last call button.
This is allowed for the combination with VisoOpt only!

Dok.-Nr.: SUP-VOP001 Date Version

Extension terminal VO-ZT (-B Version) Created by: Albrechtsberger

Checked by: Pecha
04.04.06 04
(FC008951-B)
VisoOpt Kapitel Seite

Schrack Seconet 03 02
 VO-ZT
T-GND

RA3

RA4

RA6
RA5
BL3

BL4

BL6
BL5
ZA2
ZA1
ZE2
ZE1

RA1

RA8

RA7
RA2

BL1

BL8

BL7
BL2

Maximum of 15 additional terminals per base terminal

extension terminals need to be obstructed (with

For being able to show all calls on the second
display (parallel-display) the same number of
Maximum length of dataline (cable) 1200ml

a maximum of 2 parallel base terminals).

VO-ZT

T-GND
RA3

RA4

RA6
RA5
BL3

BL4

BL6
BL5

ZA2
ZA1
ZE2
ZE1
RA1

RA8

RA7
RA2

BL1

BL8

BL7
BL2
VO-ZT

T-GND
RA3

RA4

RA6
RA5
BL3

BL4

BL6
BL5

ZA2
ZA1
ZE2
ZE1
RA1

RA8

RA7
RA2

BL1

BL8

BL7
BL2

Maximum of 2 base terminals

VO-BT

VO-BT

GND GND
RA1

RA1
RA2

RA2
BL1

BL1
BL2

BL2

RF-A ZA2 RF-A ZA2

RF-R ZA1 RF-R ZA1
ZE2 ZE2
RF-W RF-W
ON

ON

ZE1 ZE1
1 2 3 4 5 6 7 8

1 2 3 4 5 6 7 8

ST-A ST-A
ST-R ST-R
ST-W ST-W
BE1

BA1

BE1

BA1
RA4

RA3

RA4

RA3
BE2

BA2

BE2

BA2
BL4

BL3

BL4

BL3

Cabling: Maximum 1200m

Set switch 5 to ON in order to activate the connection between two units of typ VO-BT (max. 2 base terminals parallel).
Set switch 6 to ON in order to activate the connection to units of type VO-ZT (max. 15 extention terminals per base terminal).
Using such an interconnection all VO-BT´s and VO-ZT´s are to be supplied with the same voltage!

Dok.-Nr.: SUP-VOP001 Date Version

Created by: Albrechtsberger
Checked by: Pecha
11.03.05 04
Cross-linking of VO-BT’s and VO-ZT’s units VisoOpt Kapitel Seite

Schrack Seconet 04 01
Call-Push button (FC0084xx--) and Call-Push
button with finding light (FC0084xx-A) can be mixed.
If you change Call-Push button (FC0084xx--) against
Call-Push button with finding light (FC0084xx-A)
and you use no cabling witch GND connaction,
you would have the same function as before
(no finding light).

Call button RT Pull Switch ZT

from Version FC008400-A from Version FC008410-A
with finding light Call button RT Pull switch ZT with finding light

oben oben

Gnd
+ BL +
BL R Gnd
+ +

R
R
BL BL

R
R

R
R
R

Pneumatic button PT Cancel button AT

oben oben

+ A
BL BL
R

R +

The T-GND wire is to be attached to the

+ clip of the cancel button!

If buttons are connected in series, the resitor in all buttons is to be detached, except for the last button.
(See jumper on the base terminal or on the externsion terminal)

RA
BL
+ 24 V
T-GND
The T-GND wire is to be attached to
the + clip of the cancel button!

R R
BL

BL
+

+
R

A
oben

oben
BL

BL
+
R

+
R
oben
oben

PT RT ZT AT
Attention: The connectiong terminal for the acknowledgement-button
is to be connected to T-GND.
This is allowed for the combination with VisoOpt only!

RA
BL
+ 24 V
Gnd
from Version FC0084xx-A

T-Gnd

R
Attention: This connection is only possible
Gnd

BL
BL

+
+
+

BL
R

R Gnd with DC (DC power supply)

BL
+
R

R
oben

PT RT ZT AT
Dok.-Nr.: SUP-VOP001 Date Version
Created by: Albrechtsberger
Checked by: Pecha
04.04.06 05
Connection of Buttons VisoOpt Kapitel Seite

Schrack Seconet 05 01
 VO-BT or VO-ZT

Case for radio receiver with12pin

Case from front side

11 12

+1 4 5
2 3
-

3k3
15k
RA

BL
15k Ohms resistor:
see jumper 5 on base terminal (Jumper 1 to 4 at -B Version)
see jumper 9 on extension terminal (Jumper 1 to 8 at -B Version)

+24V
4A Connect to the positive here
rt sw

Tr because of the fuse

Current converter

- - + +

24V DC to next unit

NB: This connection is only possible with DC (DC power supply)

The same applies for use with Wanderer Control control units!

Dok.-Nr.: SUP-VOP001 Date Version

Created by: Albrechtsberger
Checked by: Pecha
11.03.05 05
Radio receiver 12 pin VisoOpt Kapitel Seite

Schrack Seconet 05 02
 VO-BT or VO-ZT

Jumper on unit SVM-K controls terminal resistor.

For setting see jumper on base terminal
or on extension terminal
GND
BL
+
R

SVM-K
RA
BL

+24V
4A Connect to the positive here
rt sw

Tr because of the fuse

Current converter

- - + +

24V AC - - to next unit

+ +

NB: This connection is only possible with DC (DC power supply)

The same applies for use with Wanderer Control control units!

Dok.-Nr.: SUP-VOP001 Date Version

Created by: Albrechtsberger
Checked by: Pecha
02.10.03 03
Connection device SVM-K VisoOpt Kapitel Seite

Schrack Seconet 05 03
 15k Ohms resistor:
see jumper 5 on base terminal (Jumper 1 to 4 at -B Version)
see jumper 9 on extension terminal (Jumper 1 to 8 at -B Version)

VO-BT oder VO-ZT

Radio receiver in-wall
Fc007952--
+
-

normally open contact

3k3
15k

R-Z
RA

BL
+24V

+24V
4A Connect to the positive here
rt sw

Tr because of the fuse

Gleichrichter

- - + +
GND

24V AC to next unit

NB: This connection is only possible with DC (DC power supply)

Dok.-Nr.: SUP-VOP001 Date Version

Created by: Albrechtsberger
Checked by: Pecha
11.03.05 03
Radio receiver in-wall VisoOpt Kapitel Seite

Schrack Seconet 05 04
Adjustment:
Jumper J1 (position 1-2) serves the call circuit monitoring.
Are multiple radio receiver series-connected so is the jumper J1 to be
connected to the last radio receiver only!

15k Ohms resistor:

see jumper 5 on base terminal (Jumper 1 to 4 at -B Version)
see jumper 9 on extension terminal (Jumper 1 to 8 at -B Version)

VO-BT oder VO-ZT

GND Störung

3 3
2
ZL-R Ruf

2
1 1
J2 J1
R-ST
R-Z

R-Z
RA
ZL-R
BL
+24V

+24V
4A Connect to the positive here
rt sw

Tr because of the fuse

Gleichrichter

- - + +
GND

24V AC to next unit

NB: This connection is only possible with DC (DC power supply)

Dok.-Nr.: SUP-VOP001 Date Version

Created by: Albrechtsberger
Checked by: Pecha
11.03.05 03
Radio receiver 6 pin VisoOpt Kapitel Seite

Schrack Seconet 05 05
 Wiring of external call buttons
(third party systems)

15k

+24V VisoOp
VisoOpt 3k3 call input

External
call button

Dok.-Nr.: SUP-VOP001 Date Version

Created by: Albrechtsberger
Checked by: Pecha
11.03.05 01
Third party call buttons VisoOpt Kapitel Seite

Schrack Seconet 05 06