Nexus Control System

—I/O

Nexus I/O system is designed to serve a wide

variety of industrial process control and
protection applications from boiler control
and protection, steam turbine control and
protection, to power generation balance of
plant (BOP) equipment.

www.bhge .com
Fully-covered Industrial Power Supply • Fuse for each DC branch
• Cabinet: Dual redundant 110V/220V
IO Types AC (±10%)
• Dimension: 127mm x 120mm x
23mm（High x Width x Depth）
Most of the applications could be
• Module: Dual redundant 24V DC
fulfilled by general IO modules (AI, Analog Input: MAI50 (MAI52)
(±10%)
AO, DI, DO, TC/RTD) with simplified IO • 16(8) Channels in 2(1) groups (8
design and reduced spare parts. The Environment channels in 1 group)
scalable system design can fit any • Working Temperature: -20~70℃ • Resolution: 16 bit
applications with different scope. • Humidity: 5-95% Relative (Non- • Signal Range: ±10V, ±5V, 0(4)-
Condensing) 20mA
Rugged IO with
Standard Cabinet • Accuracy: 0.1%
Distributed Installation • IP Rating: IP56
The feature of distributed installation • Channel to channel isolation:
• Cabinet Dimension: 250VAC
bring customer great feasibility to
800×600×2200mm (W×D×H)
install the IO modules inside or outside • Channel to ground isolation: 500VAC
the room, individually or in group. Field • Module Dimension:
• Channel to system isolation:
installation with equipment would save 209×129.5×51mm (H×W×D)
1500VAC
lots of cables and installation cost. • Capacity: 28 IO modules max
Temperature Input MAI51
Compact and low power consumption Regulation and Standard • 16 Channels in 2 groups
design make the IO module more • Certification: CE, FCC, UL, KC, CU-
reliable working in the harsh • Resolution: 16bit
TR, Russian Metrology, UL508A, CSA
environment with shock/vibration and C22.2 • RTD Type (2-wire or 3-wire): Pt10,
pollution. Pt100, Cu10, Cu50, BA1, Cu100,
• Safety Standard: IEC61010
Cu53
Higher availability • EMC Standard: IEC61326
• TC Type: E, J, K, N, R, S, T, B
with Fault-tolerant I/O Communication Bus: iLINK • Accuracy: 0.2%
Technology • Speed: 2Mbps
• Channel to ground isolation: 500VAC
Redundancy is the basic concept in • 1:1 Redundancy
• Channel to system isolation:
the system design including controller, • Capability: 14 IO modules per iLink 1500VAC
communication and power supply. The
• Time synchronization: ±100us
system can work normally without any Analog Input: MAI54
performances degrade at any single iLink Extension Module: MCD51 • 8 Channels, individual ADC
point failure situation. • Power Input: Dual 24V DC • Resolution: 16 bit
• Power Output: Dual 24V DC x 2 + 2 • Signal Range: ±10V, ±5V, 0(4)-20mA
Reduced Maintenance groups aux 24V DC (4 outputs/group)
• Accuracy: 0.1%
Cost • iLink extension input: Two DB-9
• Channel to channel isolation:1000VAC
High diagnostic coverage helps female connectors
customer to quickly identify any • Channel to ground isolation: 1000VAC
• iLink extension output: Four DB-9
defect or potential failure and fix it to male connectors (iLink R/iLink S, 2 • Channel to system isolation: 1500VAC
minimize un-planned outage. Hot-Swap pairs)
capability helps customer to conduct
online replacement.
Analog Output MAO50 Discrete Output MDO55(MDO56) Valve Position Control Module
• 8 Channels with individual DAC • 16 Channels Transistors output, MVP50
• Resolution: 12 bit souring(sinking) • 2 Channels LVDT Input

• Signal type: 0(4)-20mA, 0/1-5V • Output voltage: 24V/48V DC • 2 Channels Analog Input (±10V,
• Output Capability: 0.5A for each ±5V, 0(4) - 20mA)
• Accuracy: 0.2%
channel, total 2A for one module • 6 Channels Discrete Input
• Channel to ground isolation: 500VAC
• Aux Power Supply (MDO55): Dual • 2 Channels Servo Output (±40mA)
• Channel to system isolation: redundant 24/48V DC
1500VAC • 2 Channels Analog Output (0-5V)
Analog Input with HART MHT50 TMR Emergency Trip Module MLP50/
Discrete Input MDI50 (MDI52) • 8 Input Channels
• 32(16) Channels, Dry contact BLP50
• Resolution: 16 bit • Triple Redundancy Configuration
• Wetting Voltage: 48V DC (Internal
Provided) • Signal Range: ±10V, ±5V, 0(4)- • 3 Channels Speed Input
20mA • 42 Channels Discrete Input
• SOE Function
• Accuracy: 0.1% • 6 Channels Discrete Output
• Pulse Input Function, 0-1.5KHz
• Support HART protocol V5/V6/V7 • Onboard protection logic processing
• 220VAC Protection
• Channel to channel isolation: • 2 out of 3 hard-wired protection
• Channel to ground isolation: 500VAC 250VAC output voting
• Channel to system isolation: • Channel to ground isolation: 500VAC
1500VAC
• Channel to system isolation:
Discrete Input MDI53 1500VAC
• 16 Channels, dry contact
Analog Output with HART MHO50
• Wetting Voltage: 24/48/125 V DC • 8 Input Channels
• Aux Power: Dual Redundant 125V DC • Resolution: 12 bit
• Pulse Input 0-1.2KHz • Signal Range: 0(4)-20mA, 0/1-5V
• 220VAC Protection • Accuracy: 0.2%
• Channel to ground isolation: 500VAC • Support HART protocol V5/V6/V7
• Channel to system isolation: • Channel to ground isolation: 500VAC
1500VAC
• Channel to system isolation:
Discrete Output MDO53(MDO53A) 1500VAC
• 16 Channels Relay output (8 Relay
outputs+8 Discrete outputs) Speed Measuring & Protection
Module MSP50
• Relay Contact: 250VAC@12A; • 1 Channel Speed Input
30VDC@12A
• 6 Channels Analog Input
• Discrete output 24VDC@100mA
• 8 Channels Discrete Input
Discrete Output MDO54
• 6 Channels Discrete Output
• 16 Channels Transistors output
• Fail-safe output
• Output Capability: 24VDC @ 100mA
• Overspeed protection
• Pair with BDO20 to provide 220VDC
Relay output (500VAC@16A, • Load dump anticipation
220VDC@10A)
GE Digital Solutions

GE Digital Solutions is an industry-leading innovator whose business involves sensing

and measuring, nondestructive detection, condition monitoring, and automation and
optimized control, enabling customers to achieve higher accuracy, greater efficiency,
and better safety with the aim to increased value and production. Its product
portfolio has been widely used in such sectors as aeronautics and aerospace, oil and
gas, power generation, transportation, etc. We have set up more than 40 enterprises
across 25 countries, and are a subordinate to GE Oil & Gas, providing industrial
customers with asset health solutions that are more environment-friendly, much
smarter, and even more efficient and effective.

China Customer Service Center Hotline: 800 915 9966

Customer Service Center E-mail: [email protected]

160 Wenjing Road, Minhang Development Zone, Shanghai, 200245

Phone: (021) 2403 6666
Fax: (021) 6430 2778
http://geoilandgas.ge.com.cn/digitalsolutions/

© 2018 Baker Hughes, a GE company – All rights reserved.

2018/03 version 1