30 MN423 Instrumentation Measurement and Control

NATIONAL UNIVERSITY OF ENGINEERING
COLLEGE OF MECHANICAL ENGINEERING
MECHANICAL ENGINEERING PROGRAM
MN423 – INSTRUMENTATION, MEASUREMENT AND CONTROL
I. GENERAL INFORMATION
CODE : MN423 Instrumentation, Measurement and Control
SEMESTER : 8-10
CREDITS : 3
HOURS PER WEEK : 4 (Theory–Practice)
CONDITION : Elective
DEPARTMENT : Applied Engineering
II. COURSE DESCRIPTION

The course will provide to the students the knowledge and understanding of the instruments operation
(sensors and actuators) and the role within the process control in an industrial plant, making a sizing and
proper selection by using software based on international regulations. Also, it will release control
techniques most widely used in industry, conventional and unconventional industrial processes. Finally,
the student will provide skills in PLC, DCS, SCADA programming and data management systems as well
as an overview of the of instrumentation engineering deliverables of Control and Automation for industrial
processes.
III. COURSE OUTCOMES

1. Understand the operation of industrial sensors and actuators, selection and sizing using software and
international standards.
2. Know and proposes the solution to controllers for industrial processes using conventional and
unconventional control techniques.
3. Design and program the PLC, DCS and SCADA of common applications for the industry.
4. Meet the international standards related to instrumentation and control in industrial processes.
5. Meet and produces instrumentation deliverables in industrial processes.
IV. LEARNING UNITS

1. INSTRUMENTATION AND PROCESS CONTROL
Definitions of control. Classes of instruments. Electronic and pneumatic transmitters.
2. INDUSTRIAL SENSORS
Pressure measurement. Flow measurement. Level measurement. Temperature measurement.
Analysis and other variables: weight, density, humidity and dew point, pH meters and additional
variables.
3. FINAL CONTROL ELEMENTS - ACTUATORS

Control valves, sizing and selection. Valve actuators, sizing and selection. Final electronic
components (starting systems of electromechanical and electronic motors, variable speed drives),
sizing and selection. Other final control elements.
4. INTRODUCTION TO CONTROL OF PROCESSES

Continuous processes vs. Batch processes. Control for command and regulation. Disturbance and
regimes. Earnings. Response time and downtime. Documentation of Engineering in Instrumentation
and Control. Summary of International Standards.
5. TYPES OF AUTOMATIC CONTROL

Conventional controllers (cascade control, ratio control, anticipatory control, PID control and tuning).
Unconventional controllers (uncoupled multivariable control industrial processes, predictive and
robust). Applications of complete processing plants for mineral processing, metal processing,
1
chemical processing, water treatment plants, natural gas, etc.
6. PROGRAMMABLE LOGIC CONTROLLER - PLC

Characteristics, PLC types and languages programming based on rules. Typical blocks for PLC
programming. Basic instructions, latch and unlatch. Instructions timed and accountants. Instructions
for words, comparison and movement of words. Instructions for continuous monitoring, scaling
analog inputs and outputs. PID instruction. Jumps and subroutine instructions.
7. SCADA AND HMI PROGRAMMING SYSTEMS

Definitions. Industrial Networking Protocols. Approach and Interplay between SCADA and PLC /
DCS.
8. DOCUMENTATION OF INSTRUMENTATION FOR PROCESS CONTROL ENGINEERING

P and ID diagrams. Drawings and documentation according to ISA. Control philosophy. Control
architecture.
9. PLC AND SCADA PROGRAMMING APPLICATIONS

Application of PLC and SCADA programming in Natural Gas Plant. Introduction to Safety
Instrumented Systems and Intrinsic Safety.
V. METHODOLOGY
The course takes place in theory, practice and computer lab sessions. In the theory sessions, the
instructor presents the concepts, theorems and applications. In the laboratory sessions, simulation
software for each stage of the course (MATLAB, manufactured software under international regulations,
Step7 and SCADA software) is used to solve problems and analyze their solution. At the end of the
course, the student must submit an integration project. In all sessions, the active participation of students
are encouraged.
VI. LABORATORY AND PRACTICAL EXPERIENCES

Practice 1: Preparation of data sheets
Practice 2: Selection of flow and pressure instruments
Practice 3: Selection of temperature and level instruments
Practice 4: Evaluated practice
Practice 5: Selection of control valves
Practice 6: Selection of control valve actuators
Practice 7: Evaluated practice
Practice 8: Simulation of conventional controls by MATLAB
Practice 9: Simulation of unconventional controls by MATLAB
Practice 10: Programming PLC programming
Practice 11: PLC programming
Practice 12: Programming of industrial networking
Practice 13: SCADA and HMI programming
Practice 14: Exhibition of works
VII. EVALUATION FORMULA
The Average Grade PF is calculated as follow: PF = ( EP + 2EF + PP ) /4

PP = ( PC1 + PC2 + PC3+ PC4 ) / 4
EP: Mid-Term Exam EF: Final Exam
PP: Average of practices or monographs (not eliminate any evaluation)
VIII. BIBLIOGRAPHY
1. CREUS SOLÉ, ANTONIO
Industrial Instrumentation, Alfa Omega, Eighth Edition, 2010.
2. DESHPANDE, PRADEEP B. AND TANTALEAN, ROBERTO Z.
Process Control and Optimization, Six Sigma and Advanced Controls, 2006.
3. MURILL, P.W.
Fundamentals of Process Control Theory, Third Edition.
4. WHITT, MICHAEL D.
Successful Instrumentation and Control Systems Design, Second Edition (with CD-ROM).

30 MN423 Instrumentation Measurement and Control

Uploaded by

Document Informationclick to expand document information

Copyright:

Available Formats

30 MN423 Instrumentation Measurement and Control

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

30 MN423 Instrumentation Measurement and Control

Uploaded by

Copyright:

Available Formats

NATIONAL UNIVERSITY OF ENGINEERING

COLLEGE OF MECHANICAL ENGINEERING

MECHANICAL ENGINEERING PROGRAM

MN423 – INSTRUMENTATION, MEASUREMENT AND CONTROL

II. COURSE DESCRIPTION

III. COURSE OUTCOMES

IV. LEARNING UNITS

3. FINAL CONTROL ELEMENTS - ACTUATORS

4. INTRODUCTION TO CONTROL OF PROCESSES

5. TYPES OF AUTOMATIC CONTROL

6. PROGRAMMABLE LOGIC CONTROLLER - PLC

7. SCADA AND HMI PROGRAMMING SYSTEMS

8. DOCUMENTATION OF INSTRUMENTATION FOR PROCESS CONTROL ENGINEERING

9. PLC AND SCADA PROGRAMMING APPLICATIONS

VI. LABORATORY AND PRACTICAL EXPERIENCES

The Average Grade PF is calculated as follow: PF = ( EP + 2EF + PP ) /4

You might also like