0613DB9905R9/07

09/2007
Data Bulletin Cedar Rapids, IA, USA
Replaces 0613DB9905 Dated 06/1999

Ground-fault Systems for Circuit Breakers Equipped with

Micrologic® Trip Units
Masterpact® NT/NW, PowerPact® P- and R-frame, and Compact NS630b–
NS3200 Circuit Breakers
Ground-Fault Systems Circuit breakers equipped with Micrologic® trip units have the capability of
providing ground-fault sensing (alarm with no tripping) and ground-fault
protection (tripping) on three-phase, three-wire and three-phase, four-wire
solidly-grounded systems. The ground-fault protection feature of the
Micrologic trip units cannot be used on ungrounded or resistance grounded
systems.

It has been estimated that more than 85% of all faults begin as low-level
ground faults. Ground faults are an inadvertent flow of current between the
normal current-carrying conductors and ground. These ground faults usually
start at a low level and, if left undetected, escalate causing significant heat
and mechanical damage to the electrical system. In extreme cases, the
ground fault can escalate to a phase-to-phase fault causing major system
damage. The ground-fault systems in Micrologic trip units monitor the flow of
current in the system and detects ground-fault currents. The circuit breaker
will trip to protect the circuit, or send an alarm through the appropriate
interface equipment, depending on the option installed.
06133808

Ground-fault
Current

The National Electric Code® (NEC®) requires ground-fault protection on

solidly grounded circuits of 1000 A or more with greater than 150 V to ground
and 600 V or less phase-to-phase. This includes service entrance, feeders
and building disconnects. The NEC also requires ground-fault alarm (no
tripping) on emergency systems and allows ground-fault alarm on continuous
processes, fire pumps, and other circuits that would be more hazardous if
stopped without an orderly shutdown.

1
Ground-fault Systems for Circuit Breakers Equipped with Micrologic® Trip Units 0613DB9905R9/07
Data Bulletin 09/2007

Ground-Fault Alarm—Without All circuit breakers with Micrologic® 5.0P and 5.0H trip units come standard
Tripping with the ability to sense and report a ground-fault alarm through the optional
programmable contact module or communication network. A neutral current
sensor (NCT) must be installed in the neutral if ground-fault alarm is used on
a three-phase, four-wire system.

Ground-Fault Protection—With Ground-fault protection is available as an option on circuit breakers with

Tripping Micrologic 6.0A, 6.0P and 6.0H trip units. Circuit breakers offer three different
ground-fault sensing options: residual, ground-source return and modified
differential. The sensing options make it possible to match the ground-fault
protection to the application. The ground-fault sensing options can be
changed in the field for maximum flexibility. A neutral current sensor (NCT)
must be installed in the neutral of three-phase, four-wire systems.

Residual Ground-Fault Sensing Residual ground-fault sensing systems use one current sensor for each
current-carrying conductor. The trip unit vectorially sums the secondary
outputs from each sensor to determine if there is a ground fault and the
magnitude of the ground fault. The following diagram shows the current
sensors for a three-phase, four-wire system. There is a current sensor on
each phase and the neutral.

Circuit Breaker
06133807

Trip Unit

The sensors for the phase conductors A, B and C are inside the circuit
breaker. The neutral current transformer is installed in the neutral. If the
circuit breaker were used on a three-phase, three-wire system, the neutral
current transformer would not be necessary.

2 © 1999–2007 Schneider Electric All Rights Reserved

0613DB9905R9/07 Ground-fault Systems for Circuit Breakers Equipped with Micrologic® Trip Units
09/2007 Data Bulletin

Ground-Source Return Ground-source return ground-fault sensing systems use one current sensor
on the ground conductor. The current sensor measures the ground current
flow. The following diagram shows the current sensor for a three-phase, four-
wire system. Ground source return can also be used on grounded systems
which do not carry the neutral.

Circuit Breaker

06133806
A
B
C

Trip Unit

N
2

Ground-fault
1
Current Interface Module
Sensor

1 Minimum #14 AWG wire. 2 Minimum #14 AWG wire.

Wiring must be shielded cable Wiring must be shielded cable
or twisted pair. Maximum of or twisted pair. Maximum of 32
500 ft. (152.4 m) between ft. (10 m) between ground-fault
ground-fault interface module interface module and trip unit.
and current sensors.

Ground-source return sensing systems require the use of the optional

ground-fault interface module and a sensor installed in the ground circuit.
The current sensor and ground-fault interface module must be wired per the
installation and wiring instructions included with the ground-fault interface
module.

© 1999–2007 Schneider Electric All Rights Reserved 3

Ground-fault Systems for Circuit Breakers Equipped with Micrologic® Trip Units 0613DB9905R9/07
Data Bulletin 09/2007

Modified Differential Ground-Fault A modified differential ground-fault system is used for multiple sourced
System (MDGF) systems. Normal residual and ground-source return systems will not
correctly sum all of the circulating currents caused by the multiple neutral
paths and multiple grounds. The following diagram shows a typical main-tie-
main system. Each source transformer is grounded, and the service entrance
neutral is bonded to ground. Multiple neutral paths allow neutral current to
circulate and return to the supplying transformer by several different paths.
The ground-fault system must be capable of correctly summing these
circulating currents to minimize nuisance tripping and maximize protection.
The modified differential ground-fault sensing system requires the use of
optional ground-fault interface modules and current sensors installed in all
normal current-carrying conductors.
The current sensors and ground-fault interface modules must be wired in
parallel and the polarity of the current sensors must be maintained per the
installation and wiring instructions included with the ground-fault interface
module.

Source A
06133809

Source B
06133809

Ground-fault
Interface
Ground-fault
Modules
Interface
Modules
2 2
2 2

1 Minimum #14 AWG wire. Wiring must

be shielded
1 Minimum #14cable
AWGorwire.twisted pair.must
Wiring
Maximum 1 1
be shieldedofcable
500 ft.
or(152.4
twistedm) between
pair.
ground-fault
Maximum interface
of 500 module
ft. (152.4 and
m) between 1 1 1
2
current sensors.
ground-fault interface module and 1
2
current sensors.
2 Minimum #14 AWG wire. Wiring
must be shielded
2 Minimum #14 AWG cable
wire.orWiring
twisted
pair. Maximum
must be shielded of cable
32 ft. or
(10twisted
m)
between
pair. ground-fault
Maximum of 32 ft.interface
(10 m)
module and
between trip unit. interface
ground-fault
module and trip unit.

AA BB CC NN NN CC BB AA
FFeeeeddeerr LLooaaddss ((BBuuss AA)) FFeeeeddeerr LLooaaddss ((BBuuss BB))

In a multiple source MDGF system like in a main-tie-main system, different

types of circuit breakers (Masterpact NT/NW 3- and 6-pole, Powerpact P-,
and R-frame, and Compact NS630b-NS3200) can be used together.
Example: A Masterpact 6-pole (main), Powerpact R-frame (tie), and another
Masterpact 3-pole (main) is appropriate as long as all three circuit breakers
are connected to their correct MDGF output terminals on the MDGF
summing module (i.e. standard construction (3-pole) or wide construction
(6-pole) output terminals).

Schneider Electric USA

3700 Sixth St SW Electrical equipment should be installed, operated, serviced, and maintained only by
Cedar Rapids, IA, 52404 USA qualified personnel. No responsibility is assumed by Schneider Electric for any
1-888-SquareD (1-888-778-2733) consequences arising out of the use of this material.
www.us.SquareD.com © 1999–2007 Schneider Electric All Rights Reserved