Astm A276-05
Astm A276-05
Astm A276-05
1
Copyright by ASTM Int'l (all rights reserved);
Reproduction authorized per License Agreement with NEIL TRIGWELL (BODYCOTE MATERIALS TESTING LTD); Thu Aug 18 09:59:16 EDT 2
A 276 – 05
TABLE 1 Chemical RequirementsA
UNS Composition, %
Designa- Type Phos- Molyb-
tionB Carbon Manganese Sulfur Silicon Chromium Nickel Nitrogen Other Elements
phorus denum
Austenitic Grades
N08367 ... 0.030 2.00 0.040 0.030 1.00 20.0–22.0 23.5–25.5 6.0–7.0 0.18–0.25 Cu 0.75
S20100 201 0.15 5.5–7.5 0.060 0.030 1.00 16.0–18.0 3.5–5.5 ... 0.25 ...
S20161 ... 0.15 4.0–6.0 0.045 0.030 3.0–4.0 15.0–18.0 4.0–6.0 ... 0.08–0.20 ...
S20162 ... 0.15 4.0–8.0 0.040 0.040 2.5–4.5 16.5–21.0 6.0–10.0 0.50–2.50 0.05–0.25 ...
S20200 202 0.15 7.5–10.0 0.060 0.030 1.00 17.0–19.0 4.0–6.0 ... 0.25 ...
S20500 205 0.12–0.25 14.0–15.5 0.060 0.030 1.00 16.5–18.0 1.0–1.7 ... 0.32–0.40 ...
S20910 XM-19 0.06 4.0–6.0 0.045 0.030 1.00 20.5–23.5 11.5–13.5 1.50–3.00 0.20–0.40 Cb 0.10–0.30,
V 0.10–0.30
S21800 ... 0.10 7.0–9.0 0.060 0.030 3.5–4.5 16.0–18.0 8.0–9.0 ... 0.08–0.18 ...
S21900 XM-10 0.08 8.0–10.0 0.045 0.030 1.00 19.0–21.5 5.5–7.5 ... 0.15–0.40 ...
S21904 XM-11 0.04 8.0–10.0 0.045 0.030 1.00 19.0–21.5 5.5–7.5 ... 0.15–0.40 ...
S24000 XM-29 0.08 11.5–14.5 0.060 0.030 1.00 17.0–19.0 2.3–3.7 ... 0.20–0.40 ...
S24100 XM-28 0.15 11.0–14.0 0.045 0.030 1.00 16.5–19.0 0.50–2.50 ... 0.20–0.45 ...
S28200 ... 0.15 17.0–19.0 0.045 0.030 1.00 17.0–19.0 ... 0.75–1.25 0.40–0.60 Cu 0.75–1.25
S30200 302 0.15 2.00 0.045 0.030 1.00 17.0–19.0 8.0–10.0 ... 0.10 ...
S30215 302B 0.15 2.00 0.045 0.030 2.00–3.00 17.0–19.0 8.0–10.0 ... 0.10 ...
S30400 304 0.08 2.00 0.045 0.030 1.00 18.0–20.0 8.0–11.0 ... ... ...
S30403 304LC 0.030 2.00 0.045 0.030 1.00 18.0–20.0 8.0–12.0 ... ... ...
S30451 304N 0.08 2.00 0.045 0.030 1.00 18.0–20.0 8.0–11.0 ... 0.10–0.16 ...
S30452 XM-21 0.08 2.00 0.045 0.030 1.00 18.0–20.0 8.0–10.0 ... 0.16–0.30 ...
S30453 304LN 0.030 2.00 0.045 0.030 1.00 18.0–20.0 8.0–11.0 ... 0.10–0.16 ...
S30454 ... 0.03 2.00 0.045 0.030 1.00 18.0–20.0 8.0–11.0 ... 0.16–0.30 ...
S30500 305 0.12 2.00 0.045 0.030 1.00 17.0–19.0 11.0–13.0 ... ... ...
S30800 308 0.08 2.00 0.045 0.030 1.00 19.0–21.0 10.0–12.0 ... ... ...
S30815 ... 0.05–0.10 0.80 0.040 0.030 1.40–2.00 20.0–22.0 10.0–12.0 ... 0.14–0.20 Ce 0.03–0.08
S30900 309 0.20 2.00 0.045 0.030 1.00 22.0–24.0 12.0–15.0 ... ... ...
S30908 309S 0.08 2.00 0.045 0.030 1.00 22.0–24.0 12.0–15.0 ... ... ...
S30940 309Cb 0.08 2.00 0.045 0.030 1.00 22.0–24.0 12.0–16.0 ... ... Cb 103C-1.10
S31000 310 0.25 2.00 0.045 0.030 1.50 24.0–26.0 19.0–22.0 ... ... ...
S31008 310S 0.08 2.00 0.045 0.030 1.50 24.0–26.0 19.0–22.0 ... ... ...
S31040 310Cb 0.08 2.00 0.045 0.030 1.50 24.0–26.0 19.0–22.0 ... ... Cb 103C-1.10
S31254 ... 0.020 1.00 0.030 0.010 0.80 19.5–20.5 17.5–18.5 6.0–6.5 0.18–0.22 Cu 0.50–1.00
S31400 314 0.25 2.00 0.045 0.030 1.50–3.00 23.0–26.0 19.0–22.0 ... ... ...
S31600 316 0.08 2.00 0.045 0.030 1.00 16.0–18.0 10.0–14.0 2.00–3.00 ... ...
S31603 316LC 0.030 2.00 0.045 0.030 1.00 16.0–18.0 10.0–14.0 2.00–3.00 ... ...
S31635 316Ti 0.08 2.00 0.045 0.030 1.00 16.0–18.0 10.0–14.0 2.00–3.00 0.10 Ti 53(C+N)-0.70
S31640 316Cb 0.08 2.00 0.045 0.030 1.00 16.0–18.0 10.0–14.0 2.00–3.00 0.10 Cb 103C-1.10
S31651 316N 0.08 2.00 0.045 0.030 1.00 16.0–18.0 10.0–14.0 2.00–3.00 0.10–0.16 ...
S31653 316LN 0.030 2.00 0.045 0.030 1.00 16.0–18.0 10.0–13.0 2.00–3.00 0.10–0.16 ...
S31654 ... 0.03 2.00 0.045 0.030 1.00 16.0–18.0 10.0–13.0 2.00–3.00 0.16–0.30 ...
S31700 317 0.08 2.00 0.045 0.030 1.00 18.0–20.0 11.0–15.0 3.0–4.0 0.10 ...
S31725 ... 0.030 2.00 0.045 0.030 1.00 18.0–20.0 13.5–17.5 4.0–5.0 0.20 ...
S31726 ... 0.030 2.00 0.045 0.030 1.00 17.0–20.0 14.5–17.5 4.0–5.0 0.10–0.20 ...
S31727 ... 0.030 1.00 0.030 0.030 1.00 17.5–19.0 14.5–16.5 3.8–4.5 0.15–0.21 Cu 2.8–4.0
S32053 ... 0.030 1.00 0.030 0.010 1.00 22.0–24.0 24.0–26.0 5.0–6.0 0.17–0.22 ...
S32100 321 0.08 2.00 0.045 0.030 1.00 17.0–19.0 9.0–12.0 ... ... Ti 53(C+N)-0.70D
S32654 ... 0.020 2.0–4.0 0.030 0.005 0.50 24.0–25.0 21.0–23.0 7.0–8.0 0.45–0.55 Cu 0.30–0.60
S34565 ... 0.030 5.0–7.0 0.030 0.010 1.00 23.0–25.0 16.0–18.0 4.0–5.0 0.40–0.60 Cb 0.10
S34700 347 0.08 2.00 0.045 0.030 1.00 17.0–19.0 9.0–12.0 ... ... Cb 103C–1.10
S34800 348 0.08 2.00 0.045 0.030 1.00 17.0–19.0 9.0–12.0 ... ... Cb 103C–1.10,
Ta 0.10
Co 0.20
Austenitic-Ferritic Grades
S31100 XM-26 0.06 1.00 0.045 0.030 1.00 25.0–27.0 6.0–7.0 ... ... Ti 0.25
S31803 ... 0.030 2.00 0.030 0.020 1.00 21.0–23.0 4.5–6.5 2.5–3.5 0.08–0.20 ...
S32101 ... 0.040 4.0–6.0 0.040 0.030 1.00 21.0–22.0 1.35–1.70 0.10–0.80 0.20–0.25 Cu 0.10–0.80
S32205 ... 0.030 2.00 0.030 0.020 1.00 22.0–23.0 4.5–6.5 3.0–3.5 0.14–0.20 ...
S32304 ... 0.030 2.50 0.040 0.030 1.00 21.5–24.5 3.0–5.5 0.05–0.60 0.05–0.20 Cu 0.05–0.60
S32506 ... 0.030 1.00 0.040 0.015 0.90 24.0–26.0 5.5–7.2 3.0–3.5 0.08–0.20 W 0.05–0.30
S32550 ... 0.04 1.50 0.040 0.030 1.0 24.0–27.0 4.5–6.5 2.9–3.9 0.10–0.25 Cu 1.50–2.50
S32760E ... 0.030 1.00 0.030 0.010 1.00 24.0–26.0 6.0–8.0 3.0–4.0 0.20–0.30 Cu 0.50–1.00
W 0.50–1.00
Ferritic Grades
S40500 405 0.08 1.00 0.040 0.030 1.00 11.5–14.5 0.50 ... ... Al 0.10–0.30
S40976 ... 0.030 1.00 0.040 0.030 1.00 10.5–11.7 0.75–1.00 ... 0.040 Cb 103(C+N)-
0.80
S42900 429 0.12 1.00 0.040 0.030 1.00 14.0–16.0 ... ... ... ...
S43000 430 0.12 1.00 0.040 0.030 1.00 16.0–18.0 ... ... ... ...
2
Copyright by ASTM Int'l (all rights reserved);
Reproduction authorized per License Agreement with NEIL TRIGWELL (BODYCOTE MATERIALS TESTING LTD); Thu Aug 18 09:59:16 EDT 2
A 276 – 05
TABLE 1 Continued
UNS Composition, %
Designa- Type Phos- Molyb-
tionB Carbon Manganese Sulfur Silicon Chromium Nickel Nitrogen Other Elements
phorus denum
S44400 444 0.025 1.00 0.040 0.030 1.00 17.5–19.5 1.00 1.75–2.50 0.035 Ti+Cb 0.20+4 3
(C+N)-
0.80
S44600 446 0.20 1.50 0.040 0.030 1.00 23.0–27.0 0.75 ... 0.25 ...
S44627 XM-27F 0.010G 0.40 0.020 0.020 0.40 25.0–27.5 0.50 0.75–1.50 0.015G Cu 0.20
Cb 0.05–0.20
S44700 ... 0.010 0.30 0.025 0.020 0.20 28.0–30.0 0.15 3.5–4.2 0.020 C+N 0.025
Cu 0.15
S44800 ... 0.010 0.30 0.025 0.020 0.20 28.0–30.0 2.00–2.50 3.5–4.2 0.020 C+N 0.025
Cu 0.15
Martensitic Grades
S40300 403 0.15 1.00 0.040 0.030 0.50 11.5–13.0 ... ... ... ...
S41000 410 0.08–0.15 1.00 0.040 0.030 1.00 11.5–13.5 ... ... ... ...
S41040 XM-30 0.18 1.00 0.040 0.030 1.00 11.0–13.0 ... ... ... Cb 0.05–0.30
S41400 414 0.15 1.00 0.040 0.030 1.00 11.5–13.5 1.25–2.50 ... ... ...
S41425 ... 0.05 0.50–1.00 0.020 0.005 0.50 12.0–15.0 4.0–7.0 1.50–2.00 0.06–0.12 Cu 0.30
H
S41500 0.05 0.50–1.00 0.030 0.030 0.60 11.5–14.0 3.5–5.5 0.50–1.00 ... ...
S42000 420 0.15 min 1.00 0.040 0.030 1.00 12.0–14.0 ... ... ... ...
S42010 ... 0.15–0.30 1.00 0.040 0.030 1.00 13.5–15.0 0.35–0.85 0.40–0.85 ... ...
S43100 431 0.20 1.00 0.040 0.030 1.00 15.0–17.0 1.25–2.50 ... ... ...
S44002 440A 0.60–0.75 1.00 0.040 0.030 1.00 16.0–18.0 ... 0.75 ... ...
S44003 440B 0.75–0.95 1.00 0.040 0.030 1.00 16.0–18.0 ... 0.75 ... ...
S44004 440C 0.95–1.20 1.00 0.040 0.030 1.00 16.0–18.0 ... 0.75 ... ...
A
Maximum, unless range or minimum is indicated.
B
Designations established in accordance with Practice E 527 and SAE J 1086.
C
For some applications, the substitution of Type 304L for Type 304, or Type 316L for Type 316 may be undesirable because of design, fabrication, or service
requirements. In such cases, the purchaser should so indicate on the order.
D
Nitrogen content is to be reported for this grade.
E
% Cr + 3.3 3 % Mo + 16 3 % N $ 40.
F
Nickel plus copper shall be 0.50 % max.
G
Product analysis tolerance over the maximum limit for carbon and nitrogen shall be 0.002 %.
H
Wrought version of CA 6NM.
3
Copyright by ASTM Int'l (all rights reserved);
Reproduction authorized per License Agreement with NEIL TRIGWELL (BODYCOTE MATERIALS TESTING LTD); Thu Aug 18 09:59:16 EDT 2
A 276 – 05
TABLE 2 Mechanical Requirements
Tensile Elonga-
Yield Strength,A Reduc- Brinell
Strength, tion in 2
Diameter or Thickness, min tion of Hard-
Type Condition Finish min in. (50 mm)B
in. (mm) Area,C,D ness,E
or 4D
ksi MPa ksi MPa min, % max
min %
Austenitic Grades
N08367 A hot-finished or all 95 655 45 310 30 50 ...
cold-finished
201, 202 A hot-finished or all 75 515 40 275 40 45 ...
cold-finished
S20161 A hot-finished all 125 860 50 345 40 40 255
cold-finished all 125 860 50 345 40 40 311
S20162 A hot-finished or all 100 690 50 345 50 60 ...
cold finished
205 A hot-finished or all 100 690 60 414 40 50 ...
cold-finished
XM-19 A hot-finished or all 100 690 55 380 35 55 ...
cold-finished
As hot-finished or up to 2 (50.8), incl 135 930 105 725 20 50 ...
hot- cold-finished
rolled
over 2 to 3 (50.8 to 76.2), 115 795 75 515 25 50 ...
incl
over 3 to 8 (76.2 to 203.2), 100 690 60 415 30 50 ...
incl
S21800 A hot-finished or all 95 655 50 345 35 55 241
cold-finished
XM-10, XM-11 A hot-finished or all 90 620 50 345 45 60 ...
cold-finished
XM-29 A hot-finished or all 100 690 55 380 30 50 ...
cold-finished
XM-28 A hot-finished or all 100 690 55 380 30 50 ...
cold-finished
S24565 A hot-finished or all 115 795 60 415 35 40 ...
cold-finished
S28200 A hot-finished or all 110 760 60 410 35 55 ...
cold finished
302, 302B, 304, 304LN, A hot-finished all 75F 515 30F 205 40G 50 ...
305, 308, 309, 309S, cold-finished up to 1⁄2 (12.70) incl 90 620 45 310 30 40 ...
309Cb, 310, 310S, over 1⁄2 (12.70) 75F 515 30F 205 30 40 ...
310Cb, 314, 316,
316LN, 316Cb, 316TI,
317, 321, 347,
348
304L, 316L A hot-finished all 70 485 25 170 40G 50 ...
cold-finished up to 1⁄2 (12.70) incl. 90 620 45 310 30 40 ...
over 1⁄2 (12.70) 70 485 25 170 30 40 ...
304N, 316N A hot-finished or all 80 550 35 240 30 ... ...
cold-finished
202, 302, 304, 304N, 316, B cold-finished up to 3⁄4 (19.05) incl 125 860 100 690 12 35 ...
316N
over 3⁄4 (19.05) to 115 795 80 550 15 35 ...
1 (25.40)
over 1 (25.40) to 11⁄4 105 725 65 450 20 35 ...
(31.75)
over 11⁄4 (31.75) to 11⁄2 100 690 50 345 24 45 ...
(38.10)
over 11⁄2 (38.10) to 13⁄4 95 655 45 310 28 45 ...
(44.45)
304, 304N, 316, 316N S cold-finished up to 2 (50.8) incl 95 650 75 515 25 40 ...
over 2 to 21⁄2 (50.8 to 63.5) 90 620 65 450 30 40 ...
incl
over 21⁄2 to 3 (63.5 to 76.2) 80 550 55 380 30 40 ...
incl
XM-21, S30454, A hot-finished or all 90 620 50 345 30 50 ...
S31654 cold-finished
XM-21, S30454 B cold-finished up to 1 (25.40) incl 145 1000 125 860 15 45 ...
S31654
over 1 (25.40) to 11⁄4 135 930 115 795 16 45 ...
(31.75)
over 11⁄4 (31.75) to 11⁄2 135 895 105 725 17 45 ...
(38.10)
over 11⁄2 (38.10) to 13⁄4 125 860 100 690 18 45 ...
(44.45)
4
Copyright by ASTM Int'l (all rights reserved);
Reproduction authorized per License Agreement with NEIL TRIGWELL (BODYCOTE MATERIALS TESTING LTD); Thu Aug 18 09:59:16 EDT 2
A 276 – 05
TABLE 2 Continued
Tensile Elonga-
Yield Strength,A Reduc- Brinell
Strength, tion in 2
Diameter or Thickness, min tion of Hard-
Type Condition Finish min in. (50 mm)B
in. (mm) Area,C,D ness,E
or 4D
ksi MPa ksi MPa min, % max
min %
S30815 A hot-finished or all 87 600 45 310 40 50 ...
cold-finished 87 600 45 310 40 50 ...
S31254 A hot-finished or all 95 650 44 300 35 50 ...
cold-finished
S31725 A hot-finished or all 75 515 30 205 40 ... ...
cold-finished
S31726 A hot-finished or all 80 550 35 240 40 ... ...
cold-finished
S31727 A hot-finished or all 80 550 36 245 35 ... 217
cold-finished
S32053 A hot-finished or all 93 640 43 295 40 ... 217
cold-finished
S32654 A hot-finished or all 109 750 62 430 40 40 250
cold-finished
Austenitic-Ferritic Grades
XM-26 A hot-finished or all 90 620 65 450 20 55 ...
cold-finished
S31803 A hot-finished or all 90 620 65 448 25 ... 290
cold-finished
S32056 A hot-finished or all 90 620 65 450 18 ... 302
cold-finished
S32101 A hot-finished or all 94 650 65 450 30 ... 290
cold-finished
S32205 A hot-finished or all 95 655 65 450 25 ... 290
cold-finished
S32304 A hot-finished or all 87 600 58 400 25 ... 290
cold-finished
S32550 A hot-finished or all 109 750 80 550 25 ... 290
cold-finished
S32550 S cold-finished all 125 860 105 720 16 ... 335
S32760 A hot-finished or all 109 750 80 550 25 ... 290
cold-finished
S32760 S cold-finished all 125 860 105 720 16 ... 335
Ferritic Grades
405H A hot-finished all ... ... ... ... ... ... 207
cold-finished all ... ... ... ... ... ... 217
429 A hot-finished all 70 480 40 275 20 45 ...
cold-finished all 70 480 40 275 16 45 ...
430 A hot-finished or all 60 415 30 207 20 45 ...
cold-finished
S40976 A hot-finished or all 60 415 20 140 20 45 244
cold-finished
S44400 A hot-finished all 60 415 45 310 20 45 217
cold-finished all 60 415 45 310 16 45 217
446, XM-27 A hot-finished all 65 450 40 275 20 45 219
cold-finished all 65 450 40 275 16 45 219
S44700 A hot-finished all 70 480 55 380 20 40 ...
cold-finished all 75 520 60 415 15 30 ...
S44800 A hot-finished all 70 480 55 380 20 40 ...
cold-finished all 75 520 60 415 15 30 ...
Martensitic Grades
403, 410 A hot-finished all 70 480 40 275 20 45 ...
cold-finished all 70 480 40 275 16 45 ...
403, 410 T hot-finished all 100 690 80 550 15 45 ...
cold-finished all 100 690 80 550 12 40 ...
XM-30 T hot-finished all 125 860 100 690 13 45 302
cold-finished all 125 860 100 690 12 35 ...
403, 410 H hot-finished all 120 830 90 620 12 40 ...
cold-finished all (rounds only) 120 830 90 620 12 40 ...
XM-30 A hot-finished all 70 480 40 275 13 45 235
cold-finished all 70 480 40 275 12 35 ...
414 A hot-finished or all ... ... ... ... ... ... 298
cold-finished
414 T hot-finished or all 115 790 90 620 15 45 ...
cold-finished
S41425 T hot-finished all 120 825 95 655 15 45 321
5
Copyright by ASTM Int'l (all rights reserved);
Reproduction authorized per License Agreement with NEIL TRIGWELL (BODYCOTE MATERIALS TESTING LTD); Thu Aug 18 09:59:16 EDT 2
A 276 – 05
TABLE 2 Continued
Tensile Elonga-
Yield Strength,A Reduc- Brinell
Strength, tion in 2
Diameter or Thickness, min tion of Hard-
Type Condition Finish min in. (50 mm)B
in. (mm) Area,C,D ness,E
or 4D
ksi MPa ksi MPa min, % max
min %
S41500 T hot-finished or all 115 795 90 620 15 45 295
cold-finished
420 A hot-finished all ... ... ... ... ... ... 241
cold-finished all ... ... ... ... ... ... 255
S42010 A hot-finished all ... ... ... ... ... ... 235
cold-finished all ... ... ... ... ... ... 255
431 A hot-finished or all ... ... ... ... ... ... 285
cold-finished
440A, 440B, and 440C A hot-finished all ... ... ... ... ... ... 269
cold-finished all ... ... ... ... ... ... 285
A
Yield strength shall be determined by the 0.2 % offset method in accordance with Test Methods and Definitions A 370. An alternative method of determining yield
strength may be used based on a total extension under load of 0.5 %.
B
For some specific products, it may not be practicable to use a 2-in. or 50-mm gage length. The use of sub-size test specimens, when necessary, is permissible in
accordance with Test Methods and Definitions A 370.
C
Reduction of area does not apply on flat bars 3⁄16 in. (4.76 mm) and under in thickness as this determination is not generally made in this product size.
D
The material shall be capable of meeting the required reduction of area where listed, but actual measurement and reporting of the reduction of area are not required
unless specified in the purchase order.
E
Or equivalent Rockwell hardness.
F
For extruded shapes of all Cr-Ni grades of Condition A, the yield strength shall be 25 ksi (170 MPa) min and tensile strength shall be 70 ksi (480 MPa) min.
G
For shapes having section thickness of 1⁄2 in. (12.5 mm) or less, 30% min. elongation is acceptable.
H
Material shall be capable of being heat treated to a maximum Brinell hardness of 250 when oil quenched from 1750°F (953°C).
SUMMARY OF CHANGES
Committee A01.17 has identified the location of selected changes to this standard since the last issue,
A276 – 04, that may impact the use of this standard. (Approved March 1, 2005.)
6
Copyright by ASTM Int'l (all rights reserved);
Reproduction authorized per License Agreement with NEIL TRIGWELL (BODYCOTE MATERIALS TESTING LTD); Thu Aug 18 09:59:16 EDT 2
A 276 – 05
Committee A01.17 has identified the location of selected changes to this standard since the last issue, A276 – 03, that may
impact the use of this standard. (Approved Feb. 1, 2004.)
ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned
in this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk
of infringement of such rights, are entirely their own responsibility.
This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years and
if not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standards
and should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of the
responsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you should
make your views known to the ASTM Committee on Standards, at the address shown below.
This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,
United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the above
address or at 610-832-9585 (phone), 610-832-9555 (fax), or service@astm.org (e-mail); or through the ASTM website
(www.astm.org).
7
Copyright by ASTM Int'l (all rights reserved);
Reproduction authorized per License Agreement with NEIL TRIGWELL (BODYCOTE MATERIALS TESTING LTD); Thu Aug 18 09:59:16 EDT 2