1 2

RHS Section ( 80*40 )

C Channel ( 100*50 )

1 C Channel ( 100*50 )

C Channel ( 100*50 )
+3000
B H Beam ( 100*60 ) 2

RHS Section ( 80*40 )

3000
A H Beam ( 100*60 )

H Beam ( 100*60 )

+0
H Beam ( 100*60 )

1400
CORROGATED SHEET
1

B
3d
GRID A
2

1 2
A B

+3000
500

500

B
3D VIEW

2400

2600
3000
2700

A
1400
+0
1600

2400

PLAN @+0
GRID @1
 G

#12 @ 250C/C

1600

#12 @ 250C/C
A

3000

100
Marked B/1, B/2 & B/3 50 2600

A
SECTION
A SCALE: 1:5 G

TOP VIEW OF FOUNDATION

SCALE: 1:20

2000
200 mm

80

80
0 mm

400
40 -200 mm
Marked B/4 & B/5

100
B SECTION
B SCALE: 1:5 2600

G SECTION
SCALE: 1:20

FOOTING SCHEDULE

FOOTING DIMENSION FOOTING REINFORCEMENT

FOOTING
2710 NUMBERS L B D
BOTTOM
ALONG B ALONG L
1001 B E
F1 2600 1600 400 #12@180 C/C #12@250 C/C
M16BOLT
100 10 2700
C/1
23
23

100
BILL OF MATERIALS
23

23

WEIGHT IN KGS.
60 MARK. ITEM MATL. LENGTH REQD.
38 38 SECTION
NO. SPCN. IN mm. NOS. PC. WT. TOTAL WT.
SECTION
SECTION B Marked C/1 & C/2 E E SCALE: 1:5 B/1, B/2 & B/3
B SCALE: 1:5
1 S275 BLU100*50*6 3000.0 3 17.71 78.68

B/4 & B/5

2 S275 BPL40*80 2000.0 2 50.23 100.46

B/6 & B/7

3010
3 S275 ZPL 300-3-30*50 2000.0 2 30.28 60.56
C F C/1 & C/2
1001
100 10 3000 5 S275 HI100-6-6*60 2700 2 26.35 52.7

1001 Stee*** PL10*100 100.0 2 0.79 2

C/2
23
23

100
C/3 & C/4
23

23

6 S275 HI100-6-6*60 3000.0 2 29.39 58.78

60 1001 Stee*** PL10*100 100.0 2 0.79 2

38 38
GRAND TOTAL 355.18 KGS
SECTION
SECTION C F F SCALE: 1:5
C SCALE: 1:5 Marked C/3 & C/4

NOTES :-
1.ALL DIMENSIONS ARE IN 'MM' UNLESS OTHERWISE NOTED.
2.ANCHOR BOLT MUST BE SET STRAIGHT AND TO THE GIVEN DIMENSIONS AND THE PROJECTIONS WITH A
MAXIMUM OF 5 MM TOLERANCES.
3.ANCHOR BOLT THREADS MUST BE PROTECTED WHILE POURING THE CONCRETE AND MUST BE THOROUGHLY
CLEANED AND THE TEMPLATES ARE TO BE REMOVED AFTER POURING CONCRETE.
4.THE CUSTOMER / CONTRACTOR IS RESPONSIBLE FOR LOCATING THE BUILDING LINES AND BENCH MARKS AT
5.THE FOLLOWING ARE THE MAXIMUM ALLOWABLE TOLERANCES FOR SETTING UP THE THE ANCHOR BOLTS.
TOLERANCES. 2 MM BETWEEN ANY TWO ANCHOR BOLTS IN ANY ANCHOR BOLT GROUP.
THE SITE.
6. ALL THE ANCHOR BOLTS MUST BE SET PERPENDICULAR TO THE THEORETICAL BEARING NOTED SURFACE
UNLESS OTHERWISE.
7. COMPRESSIVE STRENGTH OF CONCRETE FC' = 4 KIP/IN2 AND YIELD STRENGTH OF BAR FY' = 60 KIP/IN2
ASSUMED IN DESIGN WHEREVER REQUIRED.