Scribd Logo
Upload

Welcome to Scribd!

  • 242 views

    Control of Monitoring and Measuring Equipment

    Uploaded by

    Linda Setya Wati
    This standard operational procedure outlines the control of monitoring and measuring equipment. It establishes that calibration of test equipment is necessary to ensure accuracy. The scope applies to relevant measuring equipment used by the division. Quality Assurance is responsible for determining equipment that requires calibration and ensuring it is calibrated according to prescribed intervals against national or international standards. Calibration status is recorded and equipment is identified as calibrated or obsolete. In-house checks are performed whenever necessary to verify proper functioning, and equipment found to be faulty is sent for service, repair or recalibration.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd

    Control of Monitoring and Measuring Equipment

    Uploaded by

    Linda Setya Wati
    242 views3 pages
    This standard operational procedure outlines the control of monitoring and measuring equipment. It establishes that calibration of test equipment is necessary to ensure accuracy. The scope applies to relevant measuring equipment used by the division. Quality Assurance is responsible for determining equipment that requires calibration and ensuring it is calibrated according to prescribed intervals against national or international standards. Calibration status is recorded and equipment is identified as calibrated or obsolete. In-house checks are performed whenever necessary to verify proper functioning, and equipment found to be faulty is sent for service, repair or recalibration.

    Copyright

    © © All Rights Reserved

    Available Formats

    DOCX, PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This standard operational procedure outlines the control of monitoring and measuring equipment. It establishes that calibration of test equipment is necessary to ensure accuracy. The scope applies to relevant measuring equipment used by the division. Quality Assurance is responsible for determining equipment that requires calibration and ensuring it is calibrated according to prescribed intervals against national or international standards. Calibration status is recorded and equipment is identified as calibrated or obsolete. In-house checks are performed whenever necessary to verify proper functioning, and equipment found to be faulty is sent for service, repair or recalibration.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd
    Download as docx, pdf, or txt
    242 views3 pages

    Control of Monitoring and Measuring Equipment

    Uploaded by

    Linda Setya Wati
    This standard operational procedure outlines the control of monitoring and measuring equipment. It establishes that calibration of test equipment is necessary to ensure accuracy. The scope applies to relevant measuring equipment used by the division. Quality Assurance is responsible for determining equipment that requires calibration and ensuring it is calibrated according to prescribed intervals against national or international standards. Calibration status is recorded and equipment is identified as calibrated or obsolete. In-house checks are performed whenever necessary to verify proper functioning, and equipment found to be faulty is sent for service, repair or recalibration.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd
    Download as docx, pdf, or txt
    of 3

    Standard Operational Procedure Doc Number.

    Rev.
    Effective Date. 10 June 2020
    CONTROL OF MONITORING AND MEASURING
    Page. Page 1 of 3
    EQUIPMENT

    CHANGE NOTE

    CN Number Description Originator Submit Date

    Approval :

    1. OBJECTIVE
    Calibration of Test Equipment is necessary to ensure that the measuring and test equipment are controlled,
    maintained and calibrated
    Standard Operational Procedure Doc Number.
    Rev.
    Effective Date. 10 June 2020
    CONTROL OF MONITORING AND MEASURING
    Page. Page 2 of 3
    EQUIPMENT

    2. SCOPE
    This procedure applies to relevant measuring and test equipment used by this division.

    3. RESPONSIBILITY & AUTHORITY


    Quality Assurance

    4. DEFINITION
    N.A

    5. REFERENCE
    5.1 Quality Manual
    5.2 ISO 9001:2008 - Clause 7.6: Control of monitoring and Measuring Equipment

    6. EQUIPMENT/TOOLING
    As per equipment needed

    7. PROCEDURE
    7.1 Inventory of Equipment
    7.1.1 Records of measuring and test equipment are maintained in “Instrument List” in the respective
    file.

    7.2 Service and Calibration Procedures.


    7.2.1 The respective Quality Assurance will determine the measuring and test equipment requiring
    calibration.
    7.2.2 The measuring and test equipment will be calibrated and adjusted at prescribed intervals or prior
    to use in accordance with the manufacturers manuals.
    7.2.3 For equipment requiring calibration against standard, it should be traceable either to national,
    international or manufacturer’s standards.
    7.2.4 For equipment that need no calibration against standards, adjustment procedure will be done
    accordingly.

    7.3 Record Keeping


    7.3.1 The calibration status will be recorded in ‘Instrument List Calibration” and will be indicated on
    the test equipment by a sticker of pass calibration.
    7.3.2 Equipment not to be used anymore, will be identified as ‘OBSOLETE’
    Standard Operational Procedure Doc Number.
    Rev.
    Effective Date. 10 June 2020
    CONTROL OF MONITORING AND MEASURING
    Page. Page 3 of 3
    EQUIPMENT

    7.4 Checking of Calibrated Equipment.


    7.4.1 In-house checking on the proper functioning of equipment is carried out or performed whenever
    necessary.
    7.4.2 If the equipment is found to be not in order or not functioning, the equipment will be sent to the
    supplier for service and repair and/or calibration. In that event, the validity of the previous test
    result will be reassessed and if necessary, the result will be reconfirmed.
    7.4.3 All functioning equipment will be stored in appropriate environmental conditions

    Process Flow:

    8. APPENDIX
    N.A

    You might also like