Re v 2 . 0 Jun.

1, 201 9

Product Specification Sheet

OLST12R-CDS1/ OLSTMRR-CDS1
RoHS Compliant 1000M&10/100/1000M Copper SFP Transceiver

SHENZHEN OLINKCOM TECHNOLOGY CO.,LTD

O l i n k c o m ’ s p r o p r i e t a r y a n d c o n f i d e n t i a l i n f o , d o n o t c o p y o r d i s t r i b u t e wi t h o u t p e r m i s s i o n
 Re v 2 . 0 Jun. 1, 201 9

Product Features
●Up to 1.25Gb/s bi-directional data links
●Compact RJ-45 connector
●Hot pluggable SFP footprint
●1Gigabit Ethernet over Cat 5 cable
●Applicable for 100m distance transmission
●Low power consumption, < 1.2W
●Access to physical layer IC via 2-wire serial bus
●1000 BASE-T operation in host systems with SERDES interface
●10/100/1000Mbps compliant in host systems with SGMII interface
●Operating case temperature:
Commerical:0 to 70 °C
Industrial:-40 to 85 °C

Applications
●Gigabit Ethernet 1000BASE-T
●Switch to Switch interface
●Switched backplane applications
●Router/Server interface
●Other optical transmission systems

Product Descriptions
The Copper Small Form Pluggable (SFP) transceivers is high performance, cost effective module compliant with
the Gigabit Ethernet and 1000BASE-T standards as specified in IEEE 802. 3-2002 and IEEE 802.3ab, which
supporting 1000Mbps data- rate up to 100 meters reach over unshielded twisted-pair CAT 5 cable. The module
supports1000 Mbps (or 10/100/1000Mbps) full duplex data-links with 5-level Pulse Amplitude Modulation (PAM)
signals. All four pairs in the cable are used with symbol rate at 250Mbps on each pair. The module provides
standard serial ID information compliant with SFP MSA, which can be accessed with address of A0h via the 2wire
serial CMOS EEPROM protocol. The physical IC can also be accessed via 2wire serial bus at address ACh.

O l i n k c o m ’ s p r o p r i e t a r y a n d c o n f i d e n t i a l i n f o , d o n o t c o p y o r d i s t r i b u t e wi t h o u t p e r m i s s i o n
 Re v 2 . 0 Jun. 1, 201 9

Absolute Maximum Ratings

Parameter Symbol Min. Max. Unit Note

Supply Voltage Vcc -0.5 4.0 V
Storage Temperature TS -40 85 °C
Relative Humidity RH 0 85 %

Note: Stress in excess of the maximum absolute ratings can cause permanent damage to the transceiver.

General Operating Characteristics

Parameter Symbol Min. Typ Max. Unit Note

Data Rate DR 10 1000 Mb/s
Supply Voltage Vcc 3.13 3.3 3.47 V
Supply Current Icc5 320 375 mA
Operating Case Temp. Tc 0 70 °C

Low-Speed Signals Electrical Interface (TOP(C) = 0 to 70℃, VCC = 3.13 to 3.47 V)

Parameter Symbol Min. Typ Max. Unit Note
SFP Output _Low VOL 0 0.5 V 1
SFP Output _High VOH Vcc - 0.5 Vcc+0.3 V 1
SFP Input_Low VIL 0 0.8 V 1
SFP Input_High VIH 2.0 Vcc+0.3 V 1

Notes:
1.4.7k to 10k pull-up to host_Vcc, measured at host side of connector
2.MOD_DEF(1) (SCL) and MOD_DEF(2) (SDA), are open drain CMOS signals. Both MOD_DEF(1) and MOD_DEF(2) must be pulled up to
host_Vcc.

High-Speed Electrical Interface (TOP(C) = -0 to 70 ℃, VCC = 3.13 to 3.47 V)

Parameter Symbol Min. Typ Max. Unit Note
Transmitter
Line Frequecy FL 125 MHz 2
Tx Output Impedance Zout,tx 100 Ω 3
Rx Input Impedance Zin.rx 100 Ω 3
Single ended data input swing Vin 250 1200 mV
Single ended data output swing Vout 350 800 mV
Rise/Fall Time Tr/Tf 175 ps 4
Tx Input Impedance Zin,tx 50 Ω
Rx Output Impedance Zout,rx 50 Ω
O l i n k c o m ’ s p r o p r i e t a r y a n d c o n f i d e n t i a l i n f o , d o n o t c o p y o r d i s t r i b u t e wi t h o u t p e r m i s s i o n
 Re v 2 . 0 Jun. 1, 201 9

Notes:
1. All high-speed signals are AC-coupled internally.
2. 5-level encoding, per IEEE 802.3
3. Differential, for all Frequencies between 1MHz and 125MHz Differential.
4. 20%-80%

Pin Defintion And Functions

Pin Symbol Name/Description Notes

1 VeeT Tx ground 1
2 Tx Fault Transmitter Fault. Not supported
3 Tx Disable Transmitter Disable. PHY disabled on high or open 2
4 MOD-DEF2 Module Definition 2. Data line for serial ID 3
5 MOD-DEF1 Module Definition 1. Clock line for serial ID 3
6 MOD-DEF0 Module Definition 0. Grounded within the module 3
7 Rate select No connection
8 LOS Loss of Signal indication. 4
9 VeeR Rx ground 1
10 VeeR Rx ground 1
11 VeeR Rx ground 1
12 RD- Receiver Inverted DATA out. AC coupled
13 RD+ Receiver Non-inverted DATA out. AC coupled
14 VeeR Rx ground 1
15 VccR Rx power supply
16 VccT Tx power supply 1
17 VeeT Tx ground
18 TD+ Transmitter Non-Inverted DATA in. AC coupled
19 TD- Transmitter Inverted DATA in. AC coupled
20 VeeT Tx ground 1

O l i n k c o m ’ s p r o p r i e t a r y a n d c o n f i d e n t i a l i n f o , d o n o t c o p y o r d i s t r i b u t e wi t h o u t p e r m i s s i o n
 Re v 2 . 0 Jun. 1, 201 9

Notes:

1. Circuit ground is connected to chassis ground

2. PHY disabled on TDIS > 2.0V or open, enabled on TDIS < 0.8V
3. Should be pulled up with 4.7k – 10k Ohms on host board to a voltage between 2.0 V and 3.6 V.MOD_DEF(0) pulls line low to indicate module is
plugged in.
4. LVTTL compatible with a maximum voltage of 2.5V. Not supported on GE-GB-P.

Package Dimensions

RJ45 Connector

Ordering Information
Part Number Description
OLST12R-CDS1 Copper SFP,1000BASE-T 1000M Only 0~70°C
OLSTMMR-CDS1 Copper SFP, 10/100/1000M 0~70°C

For More Information

SHENZHEN OLINKCOM TECHNOLOGY CO.,LTD
Add:4/F, No.2 Building, Delux Science and Technology City, GuanLan Hi-tech park,
No.5 Guanyi Road, Longhua District, Shenzhen, China
Fax: +86-755-27217051
E-mail:[email protected]
Website:www.olinkphotonics.com

O l i n k c o m ’ s p r o p r i e t a r y a n d c o n f i d e n t i a l i n f o , d o n o t c o p y o r d i s t r i b u t e wi t h o u t p e r m i s s i o n