Datasheet Display WH-2004L-YYH

Winstar Display Co.
, LTD
華凌光電股份有限公司
WEB: http://www.winstar.com.tw E-mail: [email protected]
SPECIFICATION
CUSTOMER :
MODULE NO.: WH2004L-YYH-ET#
APPROVED BY:
( FOR CUSTOMER USE ONLY ) PCB VERSION: DATA:
SALES BY APPROVED BY CHECKED BY PREPARED BY
VERSION DATE REVISED SUMMARY

PAGE NO.
B 2013/06/06 Remove IC information

Winstar Display Co., LTD MODLE NO：
華凌光電股份有限公司
DOC. FIRST ISSUE

RECORDS OF REVISION
REVISED
VERSION DATE SUMMARY
PAGE NO.
0 2007/12/04 First issue

A 2012/08/03 Modify backlight
information.
B 2013/06/06 Remove IC information
WH2004L-YYH-ET# 第 1 頁，共 23 頁
Contents
1.Module Classification Information
2.Precautions in use of LCD Modules
3.General Specification
4.Absolute Maximum Ratings
5.Electrical Characteristics
6.Optical Characteristics
7.Interface Pin Function
8.Contour Drawing &Block Diagram
9.Character Generator ROM Pattern
10.Reliability
11.Backlight Information
12.Inspection specification
13.Material List of Components for RoHs
14.Recommendable Storage
1.Module Classification Information
W H 2004 L － Y Y H － ET#
c d e f g h i j
c Brand：WINSTAR DISPLAY CORPORATION

d Display Type：H→Character Type, G→Graphic Type, T→TAB Type
e Display Font：Character 20 words, 04 Lines.
f Model serials no.
g Backlight N→Without backlight T→LED, White S→LED, High light White
Type： B→EL, Blue green A→LED, Amber L→LED, Full color
D→EL, Green R→LED, Red J→DIP LED,Blue
W→EL, White O→LED, Orange K→DIP LED,White
M→EL, Yellow Green G→LED, Green E→DIP LED, Yellow Green
F→CCFL, White P→LED, Blue H→DIP LED,Amber
Y→LED, Yellow Green X→LED, Dual color I→DIP LED, Red
G→LED, Green C→LED, Full color
h LCD Mode： B→TN Positive, Gray V→FSTN Negative, Blue
N→TN Negative, T→FSTN Negative, Black
L→VA Negative D→FSTN Negative (Double film)
H→ HTN Positive, Gray F→FSTN Positive
I→HTN Negative, Black K→FSC Negative
U→HTN Negative, Blue S→FSC Positive
M→STN Negative, Blue E→ISTN Negative, Black
G→STN Positive, Gray C→CSTN Negative, Black
Y→STN Positive, Yellow Green A→ASTN Negative, Black
i LCD Polarizer A→Reflective, N.T, 6:00 H→Transflective, W.T,6:00
Type/ D→Reflective, N.T, 12:00 K→Transflective, W.T,12:00
Temperature G→Reflective, W. T, 6:00 C→Transmissive, N.T,6:00
range/ View J→Reflective, W. T, 12:00 F→Transmissive, N.T,12:00
direction B→Transflective, N.T,6:00 I→Transmissive, W. T, 6:00
E→Transflective, N.T.12:00 L→Transmissive, W.T,12:00
j Special Code ET:English and European standard font
#:Fit in with the ROHS Directions and regulations
2.Precautions in use of LCD Modules
(1)Avoid applying excessive shocks to the module or making any alterations or modifications to it.
(2)Don’t make extra holes on the printed circuit board, modify its shape or change the components of
LCD module.
(3)Don’t disassemble the LCM.
(4)Don’t operate it above the absolute maximum rating.
(5)Don’t drop, bend or twist LCM.
(6)Soldering: only to the I/O terminals.
(7)Storage: please storage in anti-static electricity container and clean environment.
(8) Winstar have the right to change the passive components, including R3,R6 & backlight adjust
resistors. (Resistors,capacitors and other passive components will have different appearance and
color caused by the different supplier.)
(9)Winstar have the right to change the PCB Rev. (In order to satisfy the supplying stability,
management optimization and the best product performance...etc, under the premise of not affecting
the electrical characteristics and external dimensions, Winstar have the right to modify the version.)
3.General Specification
Item Dimension Unit
Number of Characters 20 characters x 4Lines －
Module dimension 146.0 x 62.5 x 13.6(MAX) mm
View area 123.5 x 43.0 mm
Active area 118.84x 38.47 mm
Dot size 0.92 x 1.1 mm
Dot pitch 0.98 x 1.16 mm
Character size 4.84 x 9.22 mm
Character pitch 6.0 x 9.75 mm
LCD type STN Positive, Yellow Green Transflective

(In LCD production, It will occur slightly color difference. We
can only guarantee the same color in the same batch.)
Duty 1/16
View direction 6 o’clock
Backlight Type LED Yellow Green
IC ST7066U
4.Absolute Maximum Ratings
Item Symbol Min Typ Max Unit
Operating Temperature TOP -20 － +70 ℃
Storage Temperature TST -30 － +80 ℃
Input Voltage VI VSS － VDD V
Supply Voltage For Logic VDD-VSS -0.3 － 7 V
Supply Voltage For LCD VDD-Vo -0.3 － 13 V
5.Electrical Characteristics
Item Symbol Condition Min Typ Max Unit
Supply Voltage For Logic VDD-VSS － 4.5 5.0 5.5 V
Supply Voltage For LCD Ta=-20℃ －－ 5.4 V
*Note VDD-V0 Ta=25℃ 4.1 4.2 4.3 V
Ta=70℃ 3.5 －－ V
Input High Volt. VIH － 0.7 VDD － VDD V
Input Low Volt. VIL － Vss － 0.6 V
Output High Volt. VOH － 3.9 － VDD V
Output Low Volt. VOL － 0 － 0.4 V
Supply Current IDD VDD=5.0V 1.0 1.2 1.5 mA
* Note: Please design the VOP adjustment circuit on customer's main board
Vdd
LCM
VR Vo
10K~20K Module
VSS
6.Optical Characteristics
Item Symbol Condition Min Typ Max Unit
θ CR≧2 0 － 20 ψ= 180°
θ CR≧2 0 － 40 ψ= 0°
View Angle
θ CR≧2 0 － 30 ψ= 90°
θ CR≧2 0 － 30 ψ= 270°
Contrast Ratio CR －－ 3 －－
T rise －－ 150 200 ms

Response Time
T fall －－ 150 200 ms
Definition of Operation Voltage (Vop) Definition of Response Time ( Tr , Tf )

Non-selected Non-selected
Condition Condition
Intensity Selected Wave Selected Condition
100％ Non-selected Wave Intensity
10%
Cr Max
Cr = Lon / Loff 90%
100%
Vop
Driving Voltage(V) Tr Tf
[positive type] 【Positive type】
Conditions :
Operating Voltage : Vop Viewing Angle(θ，φ) : 0°， 0°
Frame Frequency : 64 HZ Driving Waveform : 1/N duty , 1/a bias
Definition of viewing angle(CR≧2)

θb
θf
φ= 180°
θl
θr
φ= 270° φ= 90°
φ= 0°
7.Interface Pin Function
Pin No. Symbol Level Description
1 VSS 0V Ground
2 VDD 5.0V Supply Voltage for logic
3 VO (Variable) Operating voltage for LCD
4 RS H/L H: DATA, L: Instruction code
5 R/W H/L H: Read(MPU→Module) L: Write(MPU→Module)
6 E H,H→L Chip enable signal
7 DB0 H/L Data bus line
15 A － LED +
16 K － LED -
17 NC － No connection
18 NC － No connection
8.Contour Drawing &Block Diagram
146.0 0.5
6.0 134.0 1 Vss
11.25 123.5(VA)
118.84(AA) 2 Vdd
13.58
13.015
18.0 P2.54*17=43.18 13.6Max 3 Vo
10.75
4.75
4 RS
2.5
3.5
2.0 18- 1.0 PTH 9.0
1 18 5 R/W
6 E
7 DB0
K 8 DB1
38.47(AA)
43.0(VA)
62.5 0.5
9 DB2
55.0
10 DB3
55.5
A 11 DB4
12 DB5
13 DB6
73.00 1.6 14 DB7
4- 2.5 PTH
3.50 139.0 4- 5.0 PTH 15 A
LED B/L 16 K
6.0 17 NC
4.84 18 NC
0.98
0.92
The non-specified tolerance of dimension is ㊣0.3 mm .
1.1
1.16
9.22
9.75
DOT SIZE
SCALE 4/1
RS Com1~16
R/W Controller/Com Driver
MPU
E
DB0~DB7
ST7066U
or
Com17~32
20X4 LCD
80 series Equivalent
or
68 series
Power Circuit
Seg1~40
Vdd Seg41~120 Seg120~200
D
Bias and
VR Vo
Seg Driver Seg Driver
10K~20K Vss
M
CL1
Generator
CL2
N.V.
Vdd,Vss,V1~V5
External contrast adjustment.
Optional
Character located 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
DDRAM address 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 11 12 13
DDRAM address 40 41 42 43 44 45 46 47 48 49 4A 4B 4C 4D 4E 4F 50 51 52 53
DDRAM address 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 20 21 22 23 24 25 26 27
DDRAM address 54 55 56 57 58 59 5A 5B 5C 5D 5E 5F 60 61 62 63 64 65 66 67
9.Character Generator ROM Pattern
Table.2
Upper
4 bit
Lower LLLL LLLH LLHL LLHH LHLL LHLH LHHL LHHH HLLL HLLH HLHL HLHH HHLL HHLH HHHL HHHH
4 bit
CG
LLLL RAM
(1)
CG
LLLH RAM
(2)
CG
LLHL RAM
(3)
CG
LLHH RAM
(4)
CG
LHLL RAM
(5)
CG
LHLH RAM
(6)
CG
LHHL RAM
(7)
CG
LHHH RAM
(8)
CG
HLLL RAM
(1)
CG
HLLH RAM
(2)
CG
HLHL RAM
(3)
CG
HLHH RAM
(4)
CG
HHLL RAM
(5)
CG
HHLH RAM
(6)
CG
HHHL RAM
(7)
CG
HHHH RAM
(8)
10.Reliability
Content of Reliability Test (Wide temperature, -20℃~70℃)
Environmental Test
Test Item Content of Test Test Condition Note
High Temperature Endurance test applying the high storage 80℃
2
storage temperature for a long time. 200hrs
Low Temperature Endurance test applying the low storage -30℃
1,2
storage temperature for a long time. 200hrs
Endurance test applying the electric stress
High Temperature 70℃
(Voltage & Current) and the thermal stress to the ——
Operation 200hrs
element for a long time.
Low Temperature Endurance test applying the electric stress under -20℃
1
Operation low temperature for a long time. 200hrs
The module should be allowed to stand at 60
℃,90%RH max
High Temperature/ For 96hrs under no-load condition excluding the 60℃,90%RH
1,2
Humidity storage polarizer, 96hrs
Then taking it out and drying it at normal
temperature.
The sample should be allowed stand the
following 10 cycles of
operation
Thermal shock -20℃ 25℃ 70℃ -20℃/70℃
——
resistance 10 cycles
30min 5min 30min

1 cycle
Total fixed
amplitude : 1.5mm
Vibration
Frequency :
Endurance test applying the vibration during
Vibration test 10~55Hz 3
transportation and using.
One cycle 60
seconds to 3
directions of X,Y,Z
for Each
15 minutes
VS=800V,RS=1.5k
Endurance test applying the electric stress to the Ω
Static electricity test ——
terminal. CS=100pF
1 time
Note1: No dew condensation to be observed.
Note2: The function test shall be conducted after 4 hours storage at the normal
Temperature and humidity after remove from the test chamber.
Note3: The packing have to including into the vibration testing.
11.Backlight Information
Specification
PARAMETER SYMBOL MIN TYP MAX UNIT TEST CONDITION
Supply Current ILED 432 540 648 mA V=4.2V
Supply Voltage V 4.0 4.2 4.4 V －
Reverse Voltage VR －－ 5 V －
Luminance
IV 140 190 － CD/M2 ILED=540mA
(Without LCD)
Wave Length λp 569 572 575 nm ILED=540mA
ILED≦540mA
Life Time －－ 50000 － Hr.
25℃,50-60%RH
Color Yellow Green
Note: The LED of B/L is drive by current only, drive voltage is for reference only.
drive voltage can make driving current under safety area (current between
minimum and maximum).
2.Drive from pin15,pin16
R R
A
B/L
K
LCM
ill never get Vee output from pin15)
12.Inspection specification
NO Item Criterion AQL
Missing vertical, horizontal segment, segment contrast defect.
Missing character , dot or icon.
Display malfunction.
Electrical No function or no display.
01 0.65
Testing Current consumption exceeds product specifications.
LCD viewing angle defect.
Mixed product types.
Contrast defect.
Black or
2.1 White and black spots on display ≦0.25mm, no more than
white spots on
02 three white or black spots present. 2.5
LCD (display
2.2 Densely spaced: No more than two spots or lines within 3mm
only)
3.1 Round type : As following drawing

Φ=( x + y ) / 2 SIZE Acceptable Q TY
Φ≦0.10 Accept no dense
2.5
0.10＜Φ≦0.20 2
0.20＜Φ≦0.25 1
LCD black
0.25＜Φ 0
spots, white
03 spots,
3.2 Line type : (As following drawing)
contamination
(non-display) Length Width Acceptable Q TY
--- W≦0.02 Accept no dense
L≦3.0 0.02＜W≦0.03
2 2.5
L≦2.5 0.03＜W≦0.05
--- 0.05＜W As round type
If bubbles are visible, Size Φ Acceptable Q TY

judge using black spot Φ≦0.20 Accept no dense
Polarizer
04 specifications, not easy 0.20＜Φ≦0.50 3 2.5
bubbles
to find, must check in 0.50＜Φ≦1.00 2
specify direction. 1.00＜Φ 0
Total Q TY 3
05 Scratches Follow NO.3 LCD black spots, white spots, contamination
Symbols Define:
x: Chip length y: Chip width z: Chip thickness
k: Seal width t: Glass thickness a: LCD side length
L: Electrode pad length:
6.1 General glass chip :

6.1.1 Chip on panel surface and crack between panels:
z: Chip thickness y: Chip width x: Chip length

Z≦1/2t Not over viewing x≦1/8a
Chipped area
06 2.5
glass 1/2t＜z≦2t Not exceed 1/3k x≦1/8a
☉If there are 2 or more chips, x is total length of each chip.
6.1.2 Corner crack:
z: Chip thickness y: Chip width x: Chip length

Z≦1/2t Not over viewing x≦1/8a
area
1/2t＜z≦2t Not exceed 1/3k x≦1/8a
☉If there are 2 or more chips, x is the total length of each chip.
Symbols :
x: Chip length y: Chip width z: Chip thickness
k: Seal width t: Glass thickness a: LCD side length
L: Electrode pad length
6.2 Protrusion over terminal :
6.2.1 Chip on electrode pad :
y: Chip width x: Chip length z: Chip thickness

y≦0.5mm x≦1/8a 0 ＜ z≦t
6.2.2 Non-conductive portion:
Glass
06 2.5
crack
y: Chip width x: Chip length z: Chip thickness

y≦ L x≦1/8a 0 ＜ z≦t
☉If the chipped area touches the ITO terminal, over 2/3 of the ITO must
remain and be inspected according to electrode terminal specifications.
☉If the product will be heat sealed by the customer, the alignment mark not
be damaged.
6.2.3 Substrate protuberance and internal crack.
y: width x: length
y≦1/3L x≦a
07 Cracked glass The LCD with extensive crack is not acceptable. 2.5
8.1 Illumination source flickers when lit. 0.65
Backlight 8.2 Spots or scratched that appear when lit must be judged. 2.5
08
elements Using LCD spot, lines and contamination standards.
8.3 Backlight doesn’t light or color wrong. 0.65
9.1 Bezel may not have rust, be deformed or have fingerprints, 2.5
09 Bezel stains or other contamination.
9.2 Bezel must comply with job specifications. 0.65
10.1 COB seal may not have pinholes larger than 0.2mm or 2.5
contamination.
10.2 COB seal surface may not have pinholes through to the IC. 2.5
10.3 The height of the COB should not exceed the height 0.65
indicated in the assembly diagram.
10.4 There may not be more than 2mm of sealant outside the 2.5
seal area on the PCB. And there should be no more than three
places.
10.5 No oxidation or contamination PCB terminals. 2.5
10.6 Parts on PCB must be the same as on the production 0.65
10 PCB、COB
characteristic chart. There should be no wrong parts, missing
parts or excess parts.
10.7 The jumper on the PCB should conform to the product 0.65
characteristic chart.
10.8 If solder gets on bezel tab pads, LED pad, zebra pad or 2.5
screw hold pad, make sure it is smoothed down.
10.9 The Scraping testing standard for Copper Coating of PCB 2.5
X
Y
X * Y<=2mm2
11.1 No un-melted solder paste may be present on the PCB. 2.5
11.2 No cold solder joints, missing solder connections, 2.5
11 Soldering oxidation or icicle.
11.3 No residue or solder balls on PCB. 2.5
11.4 No short circuits in components on PCB. 0.65
12.1 No oxidation, contamination, curves or, bends on interface 2.5
Pin (OLB) of TCP.
12.2 No cracks on interface pin (OLB) of TCP. 0.65
12.3 No contamination, solder residue or solder balls on product. 2.5
12.4 The IC on the TCP may not be damaged, circuits. 2.5
12.5 The uppermost edge of the protective strip on the interface 2.5
pin must be present or look as if it cause the interface pin to sever.
12.6 The residual rosin or tin oil of soldering (component or chip 2.5
General
12 component) is not burned into brown or black color.
appearance
12.7 Sealant on top of the ITO circuit has not hardened. 2.5
12.8 Pin type must match type in specification sheet. 0.65
12.9 LCD pin loose or missing pins. 0.65
12.10 Product packaging must the same as specified on packaging 0.65
specification sheet.
12.11 Product dimension and structure must conform to product 0.65
specification sheet.
12.12 Visual defect outside of VA is not considered to be rejection. 0.65
13.Material List of Components for
RoHs
1. WINSTAR Display Co., Ltd hereby declares that all of or part of products (with the mark
“#”in code), including, but not limited to, the LCM, accessories or packages, manufactured
and/or delivered to your company (including your subsidiaries and affiliated company)
directly or indirectly by our company (including our subsidiaries or affiliated companies) do
not intentionally contain any of the substances listed in all applicable EU directives and
regulations, including the following substances.
Exhibit A：The Harmful Material List
Material (Cd) (Pb) (Hg) (Cr6+) PBBs PBDEs
Limited 100 1000 1000 1000 1000 1000

Value ppm ppm ppm ppm ppm ppm
Above limited value is set up according to RoHS.
2.Process for RoHS requirement：

(1) Use the Sn/Ag/Cu soldering surface；the surface of Pb-free solder is rougher than we used before.
(2) Heat-resistance temp.：
Reflow：250℃,30 seconds Max.；
Connector soldering wave or hand soldering：320℃, 10 seconds max.
(3) Temp. curve of reflow, max. Temp.：235±5℃；
Recommended customer’s soldering temp. of connector：280℃, 3 seconds.
14.Recommendable Storage
1. Place the panel or module in the temperature 25°C±5°C and the humidity below 65% RH
2. Do not place the module near organics solvents or corrosive gases.
3. Do not crush, shake, or jolt the module.
winstar LCM Sample Estimate Feedback Sheet
Module Number： Page: 1
1、Panel Specification：
1. Panel Type： □ Pass □ NG ,
2. View Direction： □ Pass □ NG ,
3. Numbers of Dots： □ Pass □ NG ,
4. View Area： □ Pass □ NG ,
5. Active Area： □ Pass □ NG ,
6. Operating Temperature： □ Pass □ NG ,
7. Storage Temperature： □ Pass □ NG ,
8. Others：
2、Mechanical Specification：
1. PCB Size： □ Pass □ NG ,
2. Frame Size： □ Pass □ NG ,
3. Materal of Frame： □ Pass □ NG ,
4. Connector Position： □ Pass □ NG ,
5. Fix Hole Position： □ Pass □ NG ,
6. Backlight Position： □ Pass □ NG ,
7. Thickness of PCB： □ Pass □ NG ,
8. Height of Frame to PCB： □ Pass □ NG ,
9. Height of Module： □ Pass □ NG ,
10. Others： □ Pass □ NG ,
3、Relative Hole Size：
1. Pitch of Connector： □ Pass □ NG ,
2. Hole size of Connector： □ Pass □ NG ,
3. Mounting Hole size： □ Pass □ NG ,
4. Mounting Hole Type： □ Pass □ NG ,
4、Backlight Specification：
1. B/L Type： □ Pass □ NG ,
2. B/L Color： □ Pass □ NG ,
3. B/L Driving Voltage (Reference for LED Type)： □ Pass □ NG ,
4. B/L Driving Current： □ Pass □ NG ,
5. Brightness of B/L： □ Pass □ NG ,
6. B/L Solder Method： □ Pass □ NG ,
＞＞ Go to page 2 ＜＜
winstar
Module Number： Page: 2
5、Electronic Characteristics of Module：
1. Input Voltage： □ Pass □ NG ,
2. Supply Current： □ Pass □ NG ,
3. Driving Voltage for LCD： □ Pass □ NG ,
4. Contrast for LCD： □ Pass □ NG ,
5. B/L Driving Method： □ Pass □ NG ,
6. Negative Voltage Output： □ Pass □ NG ,
7. Interface Function： □ Pass □ NG ,
8. LCD Uniformity： □ Pass □ NG ,
9. ESD test： □ Pass □ NG ,
6、Summary：
Sales signature：
Customer Signature： Date： / /

Datasheet Display WH-2004L-YYH

Uploaded by

Copyright:

Available Formats

Datasheet Display WH-2004L-YYH

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Datasheet Display WH-2004L-YYH

Uploaded by

Copyright:

Available Formats

Winstar Display Co.

MODULE NO.: WH2004L-YYH-ET#

SALES BY APPROVED BY CHECKED BY PREPARED BY

VERSION DATE REVISED SUMMARY

B 2013/06/06 Remove IC information

DOC. FIRST ISSUE

0 2007/12/04 First issue

2.Precautions in use of LCD Modules

4.Absolute Maximum Ratings

7.Interface Pin Function

8.Contour Drawing &Block Diagram

9.Character Generator ROM Pattern

13.Material List of Components for RoHs

c Brand：WINSTAR DISPLAY CORPORATION

Number of Characters 20 characters x 4Lines －

Module dimension 146.0 x 62.5 x 13.6(MAX) mm

View area 123.5 x 43.0 mm

Active area 118.84x 38.47 mm

Dot size 0.92 x 1.1 mm

Dot pitch 0.98 x 1.16 mm

Character size 4.84 x 9.22 mm

Character pitch 6.0 x 9.75 mm

LCD type STN Positive, Yellow Green Transflective

View direction 6 o’clock

Backlight Type LED Yellow Green

Operating Temperature TOP -20 － +70 ℃

Storage Temperature TST -30 － +80 ℃

Input Voltage VI VSS － VDD V

Supply Voltage For Logic VDD-VSS -0.3 － 7 V

Supply Voltage For LCD VDD-Vo -0.3 － 13 V

Supply Voltage For Logic VDD-VSS － 4.5 5.0 5.5 V

Supply Voltage For LCD Ta=-20℃ － － 5.4 V

*Note VDD-V0 Ta=25℃ 4.1 4.2 4.3 V

Input High Volt. VIH － 0.7 VDD － VDD V

Input Low Volt. VIL － Vss － 0.6 V

Output High Volt. VOH － 3.9 － VDD V

Output Low Volt. VOL － 0 － 0.4 V

Supply Current IDD VDD=5.0V 1.0 1.2 1.5 mA

T rise － － 150 200 ms

Definition of Operation Voltage (Vop) Definition of Response Time ( Tr , Tf )

Definition of viewing angle(CR≧2)

2 VDD 5.0V Supply Voltage for logic

3 VO (Variable) Operating voltage for LCD

4 RS H/L H: DATA, L: Instruction code

5 R/W H/L H: Read(MPU→Module) L: Write(MPU→Module)

6 E H,H→L Chip enable signal

7 DB0 H/L Data bus line

8 DB1 H/L Data bus line

9 DB2 H/L Data bus line

10 DB3 H/L Data bus line

11 DB4 H/L Data bus line

12 DB5 H/L Data bus line

13 DB6 H/L Data bus line

14 DB7 H/L Data bus line

30min 5min 30min

PARAMETER SYMBOL MIN TYP MAX UNIT TEST CONDITION

Supply Current ILED 432 540 648 mA V=4.2V

Supply Voltage V 4.0 4.2 4.4 V －

Wave Length λp 569 572 575 nm ILED=540mA

Supply Voltage For LCD Ta=-20℃ －－ 5.4 V

T rise －－ 150 200 ms