BRITISH STANDARD Packaging materials for terminally sterilized medical devices Part 4: Paper bags — Requirements and test methods 108 1.08020 5.040 55.080, NO COPYING WITHOUT BSI PERMISSION EX AS PERMITTED BY COPYRIGHT LAW BS EN 868-4:2009 British StandardsBS EN 868-4:2009 ‘This British Standard was published under the ‘authority ofthe Standards Policy and Strategy ‘Committee on 31 October 2009 © BSI 2009 ISBN 978 0 580 549564 National foreword ‘This British Standard is the UK implementation of EN 868-4:2009. It supersedes BS EN 868-4:1999 which is withdrawn, ‘The UK participation in its preparation was entrusted to Technical Committee LBI/36, Sterilizers, autoclaves and disinfectors. A list of organizations represented on this committee can be obtained on request to its secretary. ‘This publication does not purport to include all the necessary provisions of a contract, Users are responsible for its correct application, Compliance with a Briti from legal obligations. ish Standard cannot confer immunity Amendments/corrigenda issued since publication Date CommentsBS EN 868-4:2009 EUROPEAN STANDARD EN 868-4 NORME EUROPEENNE EUROPAISCHE NORM May 2008 Ics 11,080.30 ‘Suporsedes EN 868-4:1999 English Version Packaging for terminally sterilized medical devices - Part 4: Paper bags - Requirements and test methods Matériaux cemballage pour la dispose médicaux \Vorpackungen fir in der Endverpackung zu strisiorende strlisés au stade torminal - Pare 4 Sacs on papior Modiinprodukte- Tell 4: Papirbovtel - Anforderungen und Enigoncos of méthodes desssi Prifverfabron ‘This European Standard was approved by CEN on 23 Apri 2008 CEN members are bound to comply withthe CEN/CENELEC Intomal Regulations which stipulate the conditions for giving this Europoan Standard the statue ofa national standard without any aeration, Up-o-dale Ite and bidbographical references concerning such national standards may be oblaned on application tothe CEN Management Centre orto any CEN member. ‘This European Standard exits in three official versions (English, French, Geman). A version in anyother language made by transition Under the responsibilty of a CEN member info te own language and notified fo the CEN Management Cente has tha same status as the ‘oficial versions, CCEN members ara the national standards bodes of Avs, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia. Finland, Franco, Gormany, Greece, Hungary, caland, eland, lal, Latvia, Uthuania, Luxembourg, Maka, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Swoder, Switzorand and Urited Kingdom. J— J EUROPEAN COMMITTEE FOR STANDARDIZATION COMITE EUROPEEN DE NORMALISATION EUROPAISCHES KOMITEE FUR NORMUNG ‘Management Contre: Avenue Marnix 17, B-1000 Brussels (© 2009 CEN Allrights of exploiation in any form and by any means reserved Ft No. EN 868-4:2008: E ‘worlwide for CEN rational Members.BS EN 868-4:2009 EN 868-4:2009 (E) Contents Page Requirements... 1 2 3 Terms and definitions... 4 5 Information to be supplied by the manufacturer. Annex A (informative) Details of significant technical changes between this European Standard and the previous edition . ‘Annex B (normative) Method for the determination of ph value, chloride and sulphate in paper bags. ‘Annex C (normative) Method for the determination of the tensile strength of the back seam joint in paper bags (see 4.5.4).. iography ...BS EN 868-4:2009 EN 868-4:2009 (E) Foreword This document (EN 868-4:2009) has been prepared by Technical Committee CEN/TC 102 *Sterlizers for medical purposes”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by November 2009, and conflicting national standards shall be withdrawn at the latest by November 2009, ‘Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights, This document supersedes EN 868-4: 1999. Annex A provides details of significant technical changes between this European Standard and the previous edition. EN 868 consists of the following parts, under the general title Packaging for terminally sterilized medical devices: Part 2: Sterilization wrap — Requirements and test methods; Part 3: Paper for use in the manufacture of paper bags (specified in EN 868-4) and in the manufacture of pouches and reels (specified in EN 868-5) — Requirements and test methods; Part 4: Paper bags — Requirements and test methods; Part 5: Sealable pouches and reels of porous materials and plastic fim construction — Requirements and test methods; art 6: Paper for low temperature sterilization processes — Requirements and test methods; Part 7: Adhesive coated paper for low temperature sterilization processes — Requirements and test methods; Part 8: Re-usable sterilization containers for steam sterilizers conforming to EN 285 — Requirements and test methods; Part 9: Uncoated nonwoven materials of polyolefines — Requirements and test methods; Part 10: Adhesive coated nonwoven materials of polyolefines — Requirements and test methods. In addition, ISO/TC 198 “Sterilization of health care products" in collaboration with CEN/TC 102 "Sterlizers for medical purposes” has prepared the ENISO 11607 series “Packaging for terminally sterilized medical devices". The EN ISO 11607 series specifies general requirements for materials, sterile barrier systems and packaging systems (Part 1) and validation requirements for forming, sealing and assembly processes (Part 2) According to the CEN/CENELEC Intemal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, ‘Sweden, Switzerland and the United Kingdom. 3BS EN 868-4:2009 EN 868-4:2009 (E) Introduction ‘The EN ISO 11607 series consists of two parts under the general title "Packaging for terminally sterilized medical devices". Part 1 of this series specifies general requirements and test methods for materials, preformed sterile barrier systems, sterile barrier systems and packaging systems that are intended to maintain sterility of terminally sterilized medical devices to the point of use. Part 2 of this series specifies validation requirements for forming, sealing and assembly processes. Every sterile barrier system shall fulfil the requirements of EN ISO 11607-1. ‘The EN 868 series can be used to demonstrate compliance with one or more of the requirements specified in EN ISO 11607-1 During the revision of EN 868 parts 2 to 10 CEN/TC 102WG 4 recognized Resolution CEN/BT 21/2003 relating to the implementation of the uncertainty of measurement concept in standards. Following this Resolution and the corresponding guidance, CEN/TC 102)WG 4 has initiated a review of the test methods needed to show compliance with the requirements specified in EN 868 parts 2 to 10 with the intention that the information required by CEN/BT 21/2003 be available for inclusion in EN 868 parts 2 to 10 during one of their next revisions. CENITC 102\WG 4 also appreciates the initiatives of CEN with regard to the minimization of adverse environmental impacts by standards. It was agreed that this subject should be given priority during the next ‘edition of the EN ISO 11607 series that is the basic reference for all parts of the series EN 868,BS EN 868-4:2009 EN 868-4:2009 (E) 4 Scope This part of EN 868 provides test methods and values for paper bags manufactured from paper specified in Part 3 of EN 868, used as sterile barrier systems andior packaging systems that are intended to maintain stelity of terminally sterilized medical devices to the point of use. NOTE 1 The need fora protective packaging may be determined by the manufacturer and the usr. This part of EN 868 only introduces performance requirements and test methods that are specific to the products covered by this part of EN 868 but does not add or modify the general requirements specified in ENISO 11607-1 ‘As such, the particular requirements in 4.2 to 4.6 can be used to demonstrate compliance with one or more but not all of the requirements of EN ISO 11607-1 ‘The materials specified in this part of EN 868 are intended for single use only. NOTE2 When additional materials are used inside the sterile barrier system in order to ease the organization, drying ‘oF aseptic presentation (e.g. inner wrap, container fier indicators, packing lists, mats, instrument organizer sets, tray liners or an additional envelope around the medical device) then other requirements, including the determination of the ‘acceptability of these materials during validation activities, may apply 2 Normative references ‘The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 868-3, Packaging for terminally sterilized medical devices — Part 3: Paper for use in the manufacture of paper bags (specified in EN 868-4) and in the manufacture of pouches and reels (specified in EN 868-5) — Requirements and test methods EN ISO 1924-2, Paper and board — Determination of tensile properties — Part 2: Constant rate of elongation method (ISO 1924-2:1994) EN ISO 11140-1, Sterilization of health care products — Chemical indicators — Part 1: General requirements (ISO 11140-1:2005) EN ISO 11607-1:2008, Packaging for terminally sterilized medical devices— Part 1: Requirements for ‘materials, sterile barrier systems and packaging systems (ISO 11607-1:2006) 180 6588-2:2005, Paper, board and pulps— Determination of pH of aqueous extracts — Part 2: Hot extraction 1SO 8801, Data elements and interchange formats — Information interchange — Representation of dates and times ISO 9197, Paper, board and pulps — Determination of water-soluble chlorides 180 9198, Paper, board and pulp — Determination of water-soluble sulfates 3. Terms and definitions For the purposes of this document, the terms and definitions given in EN ISO 11607-1:2006 apply.BS EN 868-4:2009 EN 868-4:2009 (E) 4 Requirements 44 General ‘The requirements of EN ISO 11607-1 apply. NOTE 1 EN ISO 11607-1:2006, 5.1.4 refers to conditions during production and handling with respect to their impact on the product (e.9, electrostatic conductivity, bioburden if applicable) NOTE2 For validation requirements for forming, sealing and assembly processes, see EN ISO 11607-2. 4.2 Construction and design 424, General 4244 The bags shall be manufactured from single web paper specified in EN 868-3. 424.2 The following terms shall be used to describe the design of the bag: a) back ~ the surface of the bag with a longitudinal seam; b) front - the surface of the bag with no longitudinal seam; ©) _unlipped — where the length of both the front and back surfaces are the same and the front surface has a thumb cut (9 + 3) mm deep and not less than 15 mm wide; ) lipped ~ where the length of the back surface is greater than the length of the front surface by not less, than 10 mm and not more than 25 mm; 2) gusseted — where the construction of the bag includes side panels; 1) _ungusseted — where the longitudinal edges of the front and back surfaces are contiguous; 9) seal top—where there is @ continuous strip of seal adhesive on the inner surface of the front, back and gussets (if gusseted) of the top of the bag hh) plain top — where there is no seal adhesive, 4.2.1.3 The adhesive(s) used in the construction of the bag shall be water resistant and non-corrosive, subsequently referred to as "construction adhesive(s)". 4.2.2. Bottom seal formation ‘The bottom seal shall be formed by using one of the following methods: '@) the bottom shall be double folded with each fold bonded with “construction adhesive", or b) the bottom shall be sealed across the entire width with a "construction adhesive" or with a seal not less than 6,5 mm in depth, or ©) the bottom shall be sealed across the entire width as described in b) and then folded once, or more, each fold being bonded with (a) construction adhesive(s) or with a heat seal 4.23 Back seam construction 4.23.4 The longitudinal seam shall be made at the back of the bag with a continuous double line of “construction adhesive(s)’BS EN 868-4:2009 EN 868-4:2009 (E) 423.2 — Acoloured adhesive shall be used to enable a simple visual check on the continuity of both glue lines. 42.3.3 The dye shall not impair the adhesive, 4.3. Process indicator If one or more Class | indicator(s) (process indicator(s)) are printed on the pouches and tubes, the indicator's performance shall comply with the requirements of EN ISO 11140-1. Each individual indicator shall be not less than 100 mm in area. Indicators shall not be affected by the sealing procedure. 44 Seal strip 4.4.1 For bags with a seal closure the seal adhesive shall be applied as a continuous strip to the inner surface of the front, back and (if gusseted) the gussets of the bag, 4.4.2 The width of the seal strip shall be (25 + 3) mm for bags with a width not exceeding 200 mm and (40 + 3) mm for bags with a width exceeding 200 mm. 4.4.3 The top edge of the seal strip shall be positioned not less than 2 mm and not more than 10 mm from the lower lip or bottom of the thumb cut 4.8 Performance requirements and test methods 4.5.1. The pH of the aqueous extract of the paper and adhesive sandwich shall be within the range 4,5 to 8,0 when tested in accordance with Annex B. 48.2 The chloride content of the aqueous extract of the paper and adhesive sandwich, calculated as sodium chloride, shall not exceed 0,05 % when tested in accordance with Annex B, 4.8.3. The sulphate content of the aqueous extract of the paper and adhesive sandwich, calculated as sodium sulphate, shall not exceed 0,25 % when tested in accordance with Annex B. 4.5.4 The tensile strength of the back seam joint of each bag seal shall be not less than 2,20 kNim per unit width, when tested in accordance with Annex C. 46 Marking 46.1 Bags The bag shall be clearly marked with ) "Do not use ifthe sterile barrier system is damaged’ or other equivalent phrase; b) a process indicator(s) if applicable; ©) the manufacturer's or supplier's name or trade name; 6) lot aumbert; e) nominal dimensions and/or identification code, 1. Ateference number in order to trace the manufacturing history ofthe product.BS EN 868-4:2009 EN 868-4:2009 (E) 46.2. Protective packaging Each unit of protective package shall be legibly and durably marked with the following information: a) description of contents including the size, or a size code, for the bag; b) quantity; ©) the manufacturer's or supplier's name or trade name, and address; d) date of manufacture in accordance with ISO 8601; ) , lot number’ f) | the recommended storage conditions. 5 Information to be supplied by the manufacturer ‘The manufacturer shall supply instructions for recommended sealing and/or closure conditions and for the monitoring of critical parameters of seal andlor closure integrity. NOTE 1 — For validation of closure and sealing conditions, see EN ISO 11607-2 NOTE2 — Forheat seals these parameters include the range of temperature, pressure and time. NOTE 3 _ For requirements on information to be provided by the manufacturer national or regional legislation can apply, 09 in particular Directive 93/42/EEC, Annex |, Section 13,BS EN 868-4:2009 EN 868-4:2009 (E) Annex A (informative) Details of significant technical changes between this European Standard and the previous edition Changes between this European Standard and EN 868-4:1999 are the following: a) changes in order to align this European Standard with the EN ISO 11607 series, in particular by: 1) amending the main element of the tile, the scope and the terminology; 2) using EN ISO 11607-1 as normative reference regarding the general requirements for materials, sterile barrier systems and packaging systems; 3) deleting requirements that are covered by EN ISO 11607 (such as requirements on leaching of toxic substances); b) in addition to a) first dash, the scope has been modified to: 1) explain that other requirements might be of relevance for additional materials being used inside a sterile barrier system; 2) clarify that the materials covered by this European Standard are intended for single use only; 'b) restriction to apply heat sealing only has been eliminated; ©) an explanatory note has been inserted to refer the user of this European Standard to the general requirements on conditions during production and handling with respect to their impact on the product in EN ISO 11607; 4) requirements on indicators have been amended on the basis of EN ISO 11140-1; ) requirements on chloride content and sulphate content have been amended to clarify that they apply to the paper and the adhesive sandwich; ) requirement on wet tensile strength and test method have been deleted; 9) requirement on bursting strength and test in accordance with EN 285 have been deleted; h) requirements on marking have been amended; |) requirements on information to be provided by the manufacturer have been amended; {) number of samples to be used for testing the tensile strength has been reduced to five; k) test reports in the annexes have been amended; 1) informative annex on dimensions and tolerances has been deleted; im) text has been revised exitorialy (e.g. by updating normative and informative references) NOTE Thislistis not exhaustive.BS EN 868.4:2009 EN 868-4:2009 (E) Annex B (normative) Method for the determination of ph value, chloride and sulphate in paper bags B.1 Preparation of test pieces From the bag(s) cut @ number of specimens so that in each case the back seam joint and a 10 mm width of paper on either side of the joint is included. Take a sufficient number of the specimens to weigh 10 g and cut these into small squares approximately 10 mm x 10 mm, B.2 pH value Prepare an aqueous extract and determine the pH value of the extract by the method described in 180 6588-2 B.3 Chloride Prepare an aqueous extract in accordance with ISO 6588-2:2005, 7.2 except that 2 ml of potassium chloride solution isnot added and determine the chloride content in accordance with ISO 9197. B.4 Sulphate Prepare an aqueous extract in accordance with ISO 6588-2:2005, 7.2 except that 2 ml of potassium chloride solution is not added and determine the sulphate content by the method described in ISO 9198. B.5 Test report ‘The test report shall include the following information a) the pH to the nearest 0,1 pH unit; b) the percentage of sodium chloride in the extract rounded to two significant figures; ©) the percentage of sodium sulphate in the extract rounded to two significant figures; d) on request the identification of the product under test, the identification of the test-house and the date; e) the number of the standard that has been used for the corresponding test.BS EN 868-4:2009 EN 868-4:2009 (E) Annex C (normative) Method for the determination of the tensile strength of the back seam joint in paper bags (see 4.5.4) C1 Preparation of the test pieces Cut 5 strips, each 15 mm wide, from the bag(s) at right angles to the joint such that a 15 mm length of joint is in the centre of each stip. NOTE _Itis not necessary for the samples to be conditioned prior to testing nor for the tests to be carried out in a conditioned atmosphere C.2 Procedure Using the test samples carry out the test in accordance with the method given in EN ISO 1924-2. if during the test the paper fails before the specified value is achieved the test is invalidated as the seam has not been tested. The reason for the paper failure shall be investigated. C.3 Test report ‘The test report shall include the following information: f)_ the tensile strength (in kN/m per unit width) for each of the five samples rounded to two significant figures; b) on request, the identification of the product under test, the identification of the test-house and the date; c) the number of the standard that has been used for the corresponding test. nr ni smn “4BS EN 868-4:2009 EN 868-4:2009 (E) Bibliography [1] EN 1041, Information supplied by the manufacturer with medical devices [2] ENISO 11607-2, Packaging for terminally sterilized medical devices — Part 2: Validation requirements for forming, sealing and assembly processes (ISO 11607- 2:2006) [3] 93/42/EEC, COUNCIL DIRECTIVE 93/42/EEC of 14 June 1993 concerning medical devicesBS EN 868-4:2009 ree tees Bs Ui apy This page has been intentionally left blankBSI Group Headquarters 389 Chiswick High Road, London, W4 4AL, UK ‘Tel +44 (0)20 8996 9001 Fax +44 (0)20 8996 7001 www.bsigroup.com! standards BSI - British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Burope and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions, Tt is the constant aim of BSI to improve the quality of our products and services. ‘We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. ‘Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BST offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards, Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001 Email: [email protected] You may also buy directly using a debit/credit card from the BSI Shop on the Website http://www.bsigroup.com/shop In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on al its products and services. Contact Information Centre. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email: [email protected] ‘Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration, Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: [email protected] Information regarding online access to British Standards via British Standards Online can be found at http://www. bsigroup.com/BSOL, Further information about BSI is available on the BSI website at http:// www-bsigroup.com. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except. as permitted under the Copyright, Designs and Patents Act 1988 no extract may ‘be reproduced, stored in a retrieval system or transmitted in any form or by any means ~ electronic, photocopying, recording or otherwise ~ without prior written permission from BSL This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright and Licensing Manager. Tel: +44 (0)20 8996 7070 Email: [email protected]