Scribd
Upload
347 views4 pages

Dyna DM2800 Schematics

1. The document provides an overview of the power pack and electronics layout for a machine. It includes a block diagram showing the controller, distribution board, axes driver boards, power supply, and spindle motor. 2. The controller controls machine operation by sending logic signals to distribute via the distribution board to components like the axes driver boards, spindle, and I/O. The distribution board also collects signals from limit switches and sends to the controller. 3. The power first passes through a fuse and emergency switch before the transformer which provides 115V AC power. This powers supply switchers and is rectified for the spindle amplifier, with a circuit breaker protecting a stalled spindle. 4. The spindle emergency brake

Uploaded by

Ramon Hernandez
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
347 views4 pages

Dyna DM2800 Schematics

1. The document provides an overview of the power pack and electronics layout for a machine. It includes a block diagram showing the controller, distribution board, axes driver boards, power supply, and spindle motor. 2. The controller controls machine operation by sending logic signals to distribute via the distribution board to components like the axes driver boards, spindle, and I/O. The distribution board also collects signals from limit switches and sends to the controller. 3. The power first passes through a fuse and emergency switch before the transformer which provides 115V AC power. This powers supply switchers and is rectified for the spindle amplifier, with a circuit breaker protecting a stalled spindle. 4. The spindle emergency brake

Uploaded by

Ramon Hernandez
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

SECTION 4 COTD

i : r, n r r; r; r; i : i : j

NOTE:
1. J3-1 AND J3-3 : SHORT
2. C2: SPARE (47BBUF/SBV)
SECTION 4

D/A
CONVERTER AMC 50V D.C
BOARD DISTRIBUTION
BOARD POWER
SPINDLE SUPPLY
LIMIT SW AMPLIFIER
CONTROLLER BOARD FOR
AXES
BRAKE MOTORS
CONTROL
165 VDC
RS232C c

o
SYNC I/O C nVBUS
SPINDLE
MOTOR
DC SUPPLY

5A FUSE
CSPINDLE5
U Z Y X ]5V D.C.
AXES DRIVER BOARDS LOGIC
SUPPLY
OPTO RELAY
FOR COOLANT
CIRCUIT BREAKER
AND LINE FILTER
POWER PACK
fggESSS^ RES/IOOW

TRANS
FORMER
MAINS

1. Operation overview

Above is the layout of the power pack. On the next page is the block diagram of the
electronics.
The controller controls the operation of the machine. Logic signals to control the axes driver
boards, the spindle off/on, sync I/O, RS232C are sent to the distribution board which distributes
them. The distribution board also collects signals from the limit switches (via the limit switch board),
from the axes driver boards (am here) from the sync I/O and RS232C and the probe.
The axes driver boards have signals in (50V DC, 5V, STEP, DIRECTION, AM HERE) through
a connector at the back of the board. At the front is the 8 h'ne connector to the synchrostep stepper
motor. The u^,y driver boards are interchangeable, the z is not.
On the power, side the power first goes through a 10A fuse then the emergency switch then the
transformer. Internally 115V AC is used and this goes to the power supply switchers and to be
rectified for the spindle amplifier. There is a 5A circuit breaker on this line to handle a stalled
spindle.
The emergency brake on the spindle works as follows. With power on, the brake relay keeps voltage
on across a large capacitor.
When power is turned off via the emergency switch, the relay flips over and connects the stored
capacitor energy to the electric brake on the spindle.
There is sufficient energy stored in the capacitor to stop the motor.

You might also like