CASSETTE AIR CONDITIONER

Remote
Controller
Manual
KCS Series
KCS24 | KCS36 | KCS42 | KCS48

+
Mode ON/OFF Fan

Timer Sleep

Follow
LED me

Short Self
Turbo Cut clean
Table of contents

1. Specifications 4
2. Function buttons 4
3. Handling the remote controller 5
Inserting and replacing batteries 5
Installing remote control holder 5
Tips for using remote control 5
4. Remote LCD screen indicators 6
5. Basic functions 7
AUTO operation 7
COOL operation 7
DRY operation (dehumidifying) 8
FAN operation 8
HEAT operation 9
Setting the TIMER function 10
Setting both TIMER ON and TIMER OFF at the same time 11
6. Advanced functions 13
SLEEP function 13
TURBO function 13
SELF CLEAN function 13
LOCK function 14
FOLLOW ME function 14
SWING function 14
Silent function 15
Short cut function 15

Important note

Read this manual carefully before installing

or operating your new air conditioning unit.
Make sure to save this manual for future reference.

Kaden Remote Controller Manual  |  3

1. Specifications
Model RG66A1/BGEF

Rated voltage 3.0V (Dry batteries R03/LR03×2)

Signal receiving range 8m

Environment -5ºC – 60ºC

2. Function buttons
Before you begin using your new air conditioner, make sure to familiarise yourself with its remote control. The following
is a brief introduction to the remote control itself. For instructions on how to operate your air conditioner, refer to the
Basic functions and Advanced functions section of this manual.

ON/OFF
Turns the unit on or off

MODE FAN
Scrolls through operation Scrolls through fan speeds
modes as follows: as follows:
AUTO ➞ COOL ➞ DRY AUTO ➞ LOW ➞
➞ HEAT ➞ FAN MED ➞ HIGH
NOTE: Holding this button
down for 2 seconds will
activate Silent mode

TEMP +
Increases temperature
in 1ºC increments.
Mode ON/OFF Fan
(Max. temperature is 30ºC)
TIMER
Set timer to turn unit on and
off (see Basic Functions
for instructions)
TEMP –
Decreases temperature
Timer Sleep in 1ºC increments.
(Min. temperature is 17ºC)
SLEEP
Saves energy during LED Follow
me
sleeping hours SWING
Short Self
Starts and stops horizontal
Turbo Cut clean louvre movement
LED
Turns indoor unit’s LED
display on and off SWING
Starts and stops vertical
louvre movement
FOLLOW ME
Temperature sensing and room
temperature display button SELF CLEAN
Starts and stops the
TURBO units self-clean feature
Enables unit to reach SHORT CUT
preset temperature in Sets and activates your
shortest possible time favourite settings

4  |  Kaden Remote Controller Manual

3. Handling the remote controller

Inserting and replacing batteries Tips for using remote control

Your air conditioning unit comes with two AAA batteries. • The remote control must be used within 8 metres
Put the batteries in the remote control before use: of the unit.
• The unit will beep when remote signal is received.
1. Remove the back cover from the remote control, exposing
the battery compartment. • Curtains, other materials and direct sunlight can interfere
with the infrared signal receiver.
2. Insert the batteries, paying attention to match up the (+)
and (-) ends of the batteries with the symbols. • Remove batteries if the remote control will not be used
more than 2 months.
3. Install the back cover.

Installing remote control holder

The remote controller can be attached to a wall or stand by

using a remote controller holder.

1. Before installing the remote controller, check that the air Remove the back cover
conditioner receives the signals properly. to install batteries

2. Install the holder with two screws.

3. Put the remote controller in the holder.

Battery notes

For optimum product performance:

• Do not mix old and new batteries, or batteries

of different types.
• Do not leave batteries in the remote controller if you don’t Put the remote controller
plan on using the device for more than 2 months. in the holder

Battery disposal

Do not dispose of batteries as unsorted municipal waste.

Refer to local laws for proper disposal of batteries.

Kaden Remote Controller Manual  |  5

4. Remote LCD screen indicators

Information is displayed when the remote controller is powered up.

ON/OFF display
Appears when the unit
is turned on, and disappears
when the unit is turned off

Transmission indicator
Lights up when
remote sends signal
to indoor unit

Battery display
Low battery detection
MODE display
Displays the current
mode, including: Temperature/Timer display
Displays the set temperature
by default, or timer setting
AUTO COOL DRY HEAT FAN when using TIMER ON/OFF
function
• Temperature range:
TIMER ON display 17ºC – 30ºC
• T
ime setting range:
ON
0 – 24 hours
Displays when TIMER
ON is set This display is blank when
operating in FAN mode
TIMER OFF display

OFF
Displays when TIMER
OFF is set Fan speed display
Displays selected fan speed:

Low speed
Silent feature LOCK feature Medium speed
display display
High speed
Follow me feature Sleep mode
display display AUTO
Auto fan speed

This fan speed can not be adjusted

in AUTO or DRY mode

6  |  Kaden Remote Controller Manual

5. Basic functions

AUTO operation

In AUTO mode, the unit will automatically select the COOL,

FAN, HEAT or DRY mode based on the set temperature.

1. Press the MODE button to select Auto mode.

2. Set your desired temperature using the Temp + or

Temp – button.
3. Press the ON/OFF button to start the unit. 3
NOTE: FAN SPEED can’t be set in Auto mode. 1 Mode ON/OFF Fan 2

Timer Sleep

Follow
LED me

Short Self
Turbo Cut clean

COOL operation

1. Press the MODE button to select COOL mode.

2. Set your desired temperature using the Temp + or Temp –
button.
3. Press the FAN button to select the fan speed.
4. Press the ON/OFF button to start the unit.

4
Setting temperature 1 Mode ON/OFF Fan 2
The operating temperature range for units is 17ºC – 30ºC.
You can increase or decrease the set temperature in 3
1ºC increments. Timer Sleep

Follow
LED me

Short Self
Turbo Cut clean

Kaden Remote Controller Manual  |  7

 DRY operation (dehumidifying)

1. Press the MODE button to select DRY mode.

2. Set your desired temperature using the Temp + or Temp –
button.
3. Press the ON/OFF button to start the unit.

NOTE: FAN SPEED can’t be set in DRY mode.

1 Mode ON/OFF Fan 2

3
3
Timer Sleep

Follow
LED me

Short Self
Turbo Cut clean

FAN operation

1. Press the MODE button to select FAN mode.

2. Press the FAN button to select the fan speed.
3. Press the ON/OFF button to start the unit.

NOTE: You can’t set temperature in FAN mode. Your

remote control’s LCD screen will not display temperature.

1 Mode ON/OFF Fan

2
3
Timer Sleep

Follow
LED me

Short Self
Turbo Cut clean

8  |  Kaden Remote Controller Manual

 HEAT operation

1. Press the MODE button to select heat mode.

2. Set your desired temperature using the Temp + or Temp -
button.
3. Press the FAN button to select the fan speed.
4. Press the ON/OFF button to start the unit.

NOTE: As outdoor temperature drops, the performance

of your unit’s HEAT function may be affected. In such 1 Mode ON/OFF Fan 2
instances, we recommend using this air conditioner in
conjunction with other heating appliances. 4
3
Timer Sleep

Follow
LED me

Short Self
Turbo Cut clean

Kaden Remote Controller Manual  |  9

 Setting the TIMER function TIMER OFF function
The TIMER OFF function allows you to set a period of time
Your air conditioning unit has two timer-related functions: after which the unit will automatically turn off, such as
• TIMER ON – sets the amount of time after which the when you wake up.
unit will automatically turn on.
1. Press the Timer button, the Timer off indicator “ ”
• TIMER OFF – sets the amount of time after which displays and flashes. By default, the last time period
the unit will automatically turn off. that you set and an “h” (indicating hours) will appear
on the display.

TIMER ON function Note: This number indicates the amount of time after the
current time that you want the unit to turn off. For example,
The TIMER ON function allows you to set a period of time if you set TIMER OFF for 5 hours, “5.0h” will appear on the
after which the unit will automatically turn on, such as when screen, and the unit will turn off after 5 hours.
you come home from work.
2. Press the Temp + or Temp – button repeatedly to set the
1. Press the Timer button, the Timer on indicator “ ” time when you want the unit to turn off.
displays and flashes. By default, the last time period that 3. Wait 3 seconds, then the TIMER OFF function will be
you set and an “h” (indicating hours) will appear on the activated. The digital display on your remote control will
display. then return to the temperature display. The “ ” indicator
Note: This number indicates the amount of time after the remains on and this function is activated.
current time that you want the unit to turn on. For example,
if you set TIMER ON for 2.5 hours, “2.5h” will appear on the
screen, and the unit will turn on after 2.5 hours.
2. Press the Temp + or Temp – button repeatedly to set the
time when you want the unit to turn on.
1 2 x10
3. Wait 3 seconds, then theTimer
TIMER ON function will
or be
activated. The digital display on your remote control will Timer or
then return to the temperature display. The “ ” indicator
remains on and this function is activated.
6. Put the remote controller in the holder.

3 4
3 sec
1 2
x5

Timer or
MO
ON
/O
FF
Timer or MO
ON

DE
/O
FF

SH
DE CUORT
SH TE T
CUORT MP TIM
ER
TE T ON
MP TIM
ER
ON

Example: Setting unit to turn

off after 5 hours
3 4
3 sec

ON
/O
NOTE: When setting the TIMER ON or TIMER OFF
MO
ON
/O
FF

functions, up to 10 hours, the time will increase in 30

FF DE
MO SH
DE CUORT
SH TE T
CUORT MP TIM
ER
TE T ON
MP

minute increments with each press. After 10 hours and

TIM
ER
ON

Example: Setting unit to turn up to 24, it will increase in 1 hour increments. The timer
on after 2.5 hours will revert to zero after 24 hours. You can turn off either
function by setting its timer to “0.0h”.

10  |  Kaden Remote Controller Manual

 Setting both TIMER ON and TIMER OFF at the same time

Keep in mind that the time periods you set for both functions refer to hours after the current time. For example, say that the current
time is 1:00 PM, and you want the unit to turn on automatically at 7:00 PM. You want it to operate for 2 hours, then automatically
turn off at 9:00 PM.

Do the following:

1 2 3 4
x12
3 sec

Timer or

ON
/O
FF
MO
DE
SH
CUORT
TE T
MP TIM
ER
ON

5 6 7 8
x16
3 sec

Timer or

ON
/O
FF
MO
DE
SH
TE CUORT
MP T
TIM
ER
ON

Kaden Remote Controller Manual  |  11

Example: Setting the unit to turn on after 6 hours, operate for 2 hours, then turn off (see figure below)

Your remote display:

Timer is set to turn ON Timer is set to turn OFF

6 hours from current time 8 hours from current time

Timer starts Unit turns Unit turns

ON OFF

Current 2PM 3PM 4PM 5PM 6PM 7PM 8PM 9PM

time 1PM

6 hours later

8 hours later

12  |  Kaden Remote Controller Manual

6. Advanced functions

SLEEP function SELF CLEAN function

The SLEEP function is used to decrease energy use while Airborne bacteria can grow in the moisture that condenses
you sleep (and don’t need the same temperature settings around the heat exchanger in the unit. With regular use, most
to stay comfortable). This function can only be activated of this moisture is evaporated from the unit. When the self clean
via remote control. For detail, see “sleep operation” in feature is activated, your unit will clean itself automatically.
“OWNER’S MANUAL”. After cleaning, unit will turn off automatically.

You can use the self clean feature as often as you like.
NOTE: The SLEEP function is not available in FAN or
DRY mode.
NOTE: You can only activate this function in COOL or
DRY mode.

TURBO function

The TURBO function allows the unit to reach your set

temperature in the shortest amount
of time possible.

• When you select TURBO feature in COOL/HEAT mode,

the unit will blow cool/hot air with strongest wind setting
to jump-start the cooling/heating process.

Kaden Remote Controller Manual  |  13

 Hold down Fan
button for 2 seconds
to activate silent
function

Mode ON/OFF Fan Mode ON/OFF Fan

Timer Sleep Timer Sleep

Follow Follow
LED me LED me

Short Self Short Self

Turbo Cut clean Turbo Cut clean

Hold together for one

second to activate
LOCK function

LOCK function SWING function

Press Turbo button and self clean button simultaneously for

one second to lock or unlock the keyboard. Swing button
Used to stop or start vertical louvre movement and set the
desired left/right air flow direction. The vertical louvre changes
FOLLOW ME function 6 degrees in angle for each press. If held down for more than
2 seconds, the vertical louvre auto swing feature is activated.

The FOLLOW ME function enables the remote control to Swing button

measure the temperature at its current location and send
this signal to the air conditioner in 3-minute intervals. When Used to stop or start horizontal louvre movement or set
using AUTO, COOL, or HEAT modes, measuring ambient the desired up/down air flow direction. The louvre changes
temperature from the remote control (instead of from the 6 degrees in angle for each press. If held down for more than
indoor unit itself) will enable the air conditioner to optimise the 2 seconds, the louvre will swing up and down automatically.
temperature around you and ensure maximum comfort.

14  |  Kaden Remote Controller Manual

 Silent function

Hold down Fan button for 2 seconds to activate /cancel Silent

mode. Due to low frequency operation of compressor, it may
result in insufficient cooling and heating capacity.

Short cut function

• Used to restore the current settings or resume

previous settings.
• If this button is pushed when the remote controller is on,
the system will automatically revert back to the saved
settings including operating mode, setting temperature,
fan speed level and sleep feature (if activated).
• If held down for more than 2 seconds, the system will store
the current operation settings including operating mode,
setting temperature, fan speed level and sleep feature
(if activated) as a shortcut.

Kaden Remote Controller Manual  |  15

kadenair.com.au