Scribd Logo
Upload

Welcome to Scribd!

  • 42 views

    Aluminium Alloy L113 T6 Sheet: Specifications Supplied Forms

    Uploaded by

    grg_gre
    Special Aluminium Alloy Chart 2

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Aluminium Alloy L113 T6 Sheet: Specifications Supplied Forms

    Uploaded by

    grg_gre
    42 views2 pages
    Special Aluminium Alloy Chart 2

    Original Title

    Gould-Alloys-Limited_Aluminium-Alloy-L113-T6-Sheet_10

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Special Aluminium Alloy Chart 2

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    42 views2 pages

    Aluminium Alloy L113 T6 Sheet: Specifications Supplied Forms

    Uploaded by

    grg_gre
    Special Aluminium Alloy Chart 2

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 2

    Aluminium Alloy

    L113 T6 Sheet

    SPECIFICATIONS SUPPLIED FORMS


    L113-6082T6 aluminium is supplied in sheet, strip and
    Commercial 6082 plate.
    • Plate
    Aluminium alloy L113 – 6082T6 is a medium strength • Sheet
    alloy with excellent corrosion resistance. It has the • Strip
    highest strength of the 6000 series alloys. Alloy 6082
    is known as a structural alloy. In plate form, 6082 is
    the alloy most commonly used for machining. As a GENERIC PHYSICAL PROPERTIES
    relatively new alloy, the higher strength of 6082 has
    seen it replace 6061 in many applications. The addition Property Value
    of a large amount of manganese controls the grain
    Density 2.70 g/cm³
    structure which in turn results in a stronger alloy.
    In T6 temper, the alloy machines well. Melting Point 555 °C
    Thermal Expansion 24 x10-6 /K
    CHEMICAL COMPOSITION Modulus of Elasticity 70 GPa
    Thermal Conductivity 180 W/m.K
    BS L113(1971)
    Alloy L113 Electrical Resistivity 0.038 x10-6 Ω .m
    Element % Present
    Silicon (Si) 0.70 - 1.30
    MECHANICAL PROPERTIES
    Magnesium (Mg) 0.50 - 1.20
    Manganese (Mn) 0.40 - 1.00 BS L113(1971)
    Sheet
    Iron (Fe) 0.0 - 0.50 0.2mm to 3.0mm inc.

    Chromium (Cr) 0.0 - 0.25 Property Value


    Titanium (Ti) 0.0 - 0.20 Elongation A50 mm 8 Min %
    Zinc (Zn) 0.0 - 0.20 Tensile Strength 295 Min N/mm2
    Copper (Cu) 0.0 - 0.10 0.2% Proof Stress 255 Min N/mm2
    Nickel (Ni) 0.0 - 0.10
    Lead (Pb) 0.0 - 0.05
    Tin (Sn) 0.0 - 0.05
    Aluminium (Al) Balance

    ALLOY DESIGNATIONS
    Aluminium alloy L113 has similarities to the following
    standard designations and specifications but may not
    be a direct equivalent:
    6082

    TEMPER TYPES
    The most common temper for L113 – 6082 aluminium
    is:
    • T6 - Solution heat treated and artificially aged

    [1 OF 2] CONTINUED

    © Copyright Gould Alloys Limited / Parkway House, Unit 6 Parkway Industrial Estate, Wednesbury WS10 7WP
    Aluminium Alloy
    L113 T6 Sheet

    CONTACT

    Address: Gould Alloys Ltd


    Markham Lane
    Markham Vale
    Chesterfield
    S44 5HS
    United Kingdom
    Tel: +44 (0) 1246 263300
    Email: [email protected]
    Web: www.gouldalloys.co.uk

    REVISION HISTORY

    Datasheet Updated 08 July 2016

    DISCLAIMER
    This Data is indicative only and as such is not to be relied upon in place of
    the full specification. In particular, mechanical property requirements vary
    widely with temper, product and product dimensions. All information is
    based on our present knowledge and is given in good faith. No liability will
    be accepted by the Company in respect of any action taken by any third
    party in reliance thereon.

    Please note that the 'Datasheet Update' date shown above is no guarantee
    of accuracy or whether the datasheet is up to date.

    The information provided in this datasheet has been drawn from various
    recognised sources, including EN Standards, recognised industry references
    (printed & online) and manufacturers’ data. No guarantee is given that the
    information is from the latest issue of those sources or about the accuracy of
    those sources.

    Material supplied by the Company may vary significantly from this data, but
    will conform to all relevant and applicable standards.

    As the products detailed may be used for a wide variety of purposes and as
    the Company has no control over their use; the Company specifically
    excludes all conditions or warranties expressed or implied by statute or
    otherwise as to dimensions, properties and/or fitness for any particular
    purpose, whether expressed or implied.

    Advice given by the Company to any third party is given for that party’s
    assistance only and without liability on the part of the Company. All
    transactions are subject to the Company’s current Conditions of Sale. The
    extent of the Company’s liabilities to any customer is clearly set out in those
    Conditions; a copy of which is available on request.

    [2 OF 2]

    © Copyright Gould Alloys Limited / Parkway House, Unit 6 Parkway Industrial Estate, Wednesbury WS10 7WP

    You might also like