0% found this document useful (0 votes)
251 views4 pages

JORDAHL® EXPERT Punching Shear - Design 1. Input Information

This document provides an analysis of punching shear for a concrete slab with a rectangular column. It includes input parameters for the column, slab, loads, reinforcement, and output calculations for shear stresses and resistances at inner and outer critical sections according to ACI 318-14.

Uploaded by

kamal
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
251 views4 pages

JORDAHL® EXPERT Punching Shear - Design 1. Input Information

This document provides an analysis of punching shear for a concrete slab with a rectangular column. It includes input parameters for the column, slab, loads, reinforcement, and output calculations for shear stresses and resistances at inner and outer critical sections according to ACI 318-14.

Uploaded by

kamal
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

Responsible: Construction project:

Construction member:
Position:
Date: August 13, 2021

JORDAHL® EXPERT Punching shear - Design


1. Input information
Column type Rectangular corner column
Column dimension cx / cy = 36 in / 36 in
Edge ra / rb = 6 in / 6 in

Slab type In-situ concrete slab


Slab thickness h = 9 in
Concrete cover top/bottom co / cu = 1.1 in / 0.75 in
Effective depth dx / dy = 7 in / 7 in
Concrete strength 6000 psi
Density Normal concrete
Prestress fpc = 125 psi

Punching shear load Vu = 89 kip


Unbalanced moment Mux / Muy = 145 kip-ft / 176 kip-ft

Reinforcement diameter ϕx / ϕy = #5 / #4
Distances sx / sy = 12 in / 12 in

2. Output information (ACI 318-14)


2.1 Inner Critical Section (d/2 outside of column face)
2.1.1 Common Properties
Area Ac = 602 in²
Critical section perimeter b0 = 86 in
2.1.2 Natural Axis Properties
Centroid coordinate ex / ey = 10.75 in / 10.75 in
Section moment of inertia Ix / Iy = 1.159·105 in⁴ / 1.159·105 in⁴
4
Section product of inertia Ixy = -6.957·10 in⁴
2.1.3 Principal Axis Properties
Centroid coordinate e1 / e2 = -15.203 in / 0 in
5 4
Section moment of inertia I1 / I2 = 1.855·10 in⁴ / 4.638·10 in⁴
Principal axis rotation θ = 45.0 °
Moment fraction γ1 / γ2 = 0.4000 / 0.2675
Unbalanced moment Mu1 / Mu2 = 227 kip-ft / 21.9 kip-ft

JORDAHL H-BAU AG Wasterkingerweg 2, CH-8193 Eglisau JORDAHL® EXPERT Punching shear Page 1 from 4
www.jordahl-hbau.ch Version: 4.2.2.39
Responsible: Construction project:
Construction member:
Position:
Date: August 13, 2021

2.1.4 Stresses
Maximum shear stresss vu = 422 psi
x/y = 21.5 in / -21.5 in
Shear resistance (concrete only) ϕvc = 210.8 psi
Shear resistance (with studrails) ϕvn = 623.4 psi
Shear resistance (upper limit) ϕvn,max = 464.8 psi

2.2 Outer Critical Section (d/2 outside of reinforced zone)


2.2.1 Common Properties
Area Ac = 1248.2 in²
Critical section perimeter b0 = 178.3 in
2.2.2 Natural Axis Properties
Centroid coordinate ex / ey = 46.422 in / 46.422 in
6 6
Section moment of inertia Ix / Iy = 1.449·10 in⁴ / 1.449·10 in⁴
6
Section product of inertia Ixy = -1.334·10 in⁴
2.2.3 Principal Axis Properties
Centroid coordinate e1 / e2 = -65.65 in / 0 in
6 5
Section moment of inertia I1 / I2 = 2.783·10 in⁴ / 1.147·10 in⁴
Principal axis rotation θ = 45.0 °
Moment fraction γ1 / γ2 = 0.4000 / 0.0000
Unbalanced moment Mu1 / Mu2 = 227 kip-ft / 21.9 kip-ft
2.2.4 Stresses
Maximum shear stresss vu = 101.3 psi
x/y = 84.5 in / -24 in
Shear resistance ϕvc = 116.2 psi

3. Elements
Number of studrails per column = 8
Number of studs per studrail = 18
Stud diameter D = 0.75 in
Stud spacing S / S0 = 3.5 in / 3.5 in
Overall height of studrail OAH = 7.15 in
Overall length of studrail OAL = 66.5 in

JORDAHL H-BAU AG Wasterkingerweg 2, CH-8193 Eglisau JORDAHL® EXPERT Punching shear Page 2 from 4
www.jordahl-hbau.ch Version: 4.2.2.39
Responsible: Construction project:
Construction member:
Position:
Date: August 13, 2021

4. Note
• The design against punching shear failure is based on the rules of ACI 318-14.
• This calculation is bases on product specific properties of DECON® Studrails®. Changes, even to similar
products, are only possible with new calculations.
• All data have to be checked with the given edge boundaries and the feasibility. DECON assumes no
liability for the input data of the user.

JORDAHL H-BAU AG Wasterkingerweg 2, CH-8193 Eglisau JORDAHL® EXPERT Punching shear Page 3 from 4
www.jordahl-hbau.ch Version: 4.2.2.39
Responsible: Construction project:
Construction member:
Position:
Date: August 13, 2021

JORDAHL H-BAU AG Wasterkingerweg 2, CH-8193 Eglisau JORDAHL® EXPERT Punching shear Page 4 from 4
www.jordahl-hbau.ch Version: 4.2.2.39

You might also like