Scribd Logo
Upload

Welcome to Scribd!

  • 419 views

    01-15456 STS-1 Installation Instructions

    Uploaded by

    Robel MT
    The document provides installation instructions for an STS-1 Security Tamper Switch in 3 cabinet enclosure models. It details: 1) Installing the switch on the backbox opposite the door hinge and installing the magnet on the door. 2) Connecting the switch to different fire alarm monitor modules, including installing an end-of-line resistor. 3) Connecting the switch to an MPS-400 module by removing a jumper and connecting cable 75148.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    01-15456 STS-1 Installation Instructions

    Uploaded by

    Robel MT
    419 views2 pages
    The document provides installation instructions for an STS-1 Security Tamper Switch in 3 cabinet enclosure models. It details: 1) Installing the switch on the backbox opposite the door hinge and installing the magnet on the door. 2) Connecting the switch to different fire alarm monitor modules, including installing an end-of-line resistor. 3) Connecting the switch to an MPS-400 module by removing a jumper and connecting cable 75148.

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document provides installation instructions for an STS-1 Security Tamper Switch in 3 cabinet enclosure models. It details: 1) Installing the switch on the backbox opposite the door hinge and installing the magnet on the door. 2) Connecting the switch to different fire alarm monitor modules, including installing an end-of-line resistor. 3) Connecting the switch to an MPS-400 module by removing a jumper and connecting cable 75148.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    419 views2 pages

    01-15456 STS-1 Installation Instructions

    Uploaded by

    Robel MT
    The document provides installation instructions for an STS-1 Security Tamper Switch in 3 cabinet enclosure models. It details: 1) Installing the switch on the backbox opposite the door hinge and installing the magnet on the door. 2) Connecting the switch to different fire alarm monitor modules, including installing an end-of-line resistor. 3) Connecting the switch to an MPS-400 module by removing a jumper and connecting cable 75148.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 2

    STS-1 Security Tamper Switch

    PRODUCT INSTALLATION DRAWING


    Document 15456 Rev. C
    ECN 98-473 11/16/98

    Figure 1: Installing STS-1 Switch and Magnet in CAB-3 Series Enclosure

    1) Install the Security Tamper Switch (STS-1) on the side of the


    cabinet backbox opposite the placement of the door hinge. To
    install, push switch through the opening in backbox until it
    snaps into place.
    Security Tamper 2) Install the magnet on the same side of the cabinet door as the
    Switch (STS-1) lock. To install, push magnet through opening in door until it
    snaps into place.

    Install an R-47K End-of-Line


    Resistor into the circuit as shown
    yellow
    Figure 2: Connecting an Security Tamper
    STS-1 Switch to an Switch (STS-1)
    purple
    MMX-101 Monitor Module

    red

    black
    SLC loop MMX-101

    SLC loop out


    Install an R-47K End-of-Line
    Resistor into the circuit.
    Connect wires with wire nuts.
    Figure 3: Connecting an
    STS-1 Switch to Security Tamper
    an MMX-1 Monitor Module Switch (STS-1)

    SLC loop in

    One Fire-Lite Place


    Northford, CT 06472
    (203) 484-7161
    Fax: (203) 484-7118

    1
    Figure 4: Connecting an STS-1 Switch to an XP5-M Module

    SLC loop out

    SLC loop
    in

    Figure 5: Connecting an STS-1 Switch to an MPS-400

    Wire the STS-1 to the MPS-400:


    1) Remove the jumper from J5 on the
    MPS-400. AFP-400 in
    a CAB-A3
    2) Connect cable 75148 to J5.

    MPS-400

    Cable 75148
    Security Tamper
    connected to
    Switch (STS-1)
    J5

    Cable 75148
    J5

    For further information on the STS-1, refer to the AM2020/AFP1010 Installation Manual, Document 15088 or the
    AFP-400 Installation Manual, Document 50253.

    2 Document # 15456 Rev. C 11/16/98

    You might also like