RF Exposure Evaluation Report: Shenzhen Huaxia Testing Technology Co., LTD

Shenzhen Huaxia Testing Technology Co.
, Ltd
1F., Block A of Tongsheng Technology Building, Huahui Road, Dalang Street, Longhua District,
Shenzhen, China
Telephone: +86-755-26648640
Fax: +86-755-26648637 Report Template Version: V04
Website: www.cqa-cert.com Report Template Revision Date: 2018-07-06
RF Exposure Evaluation Report

Report No.: CQASZ20210600783E-02
Applicant: SHENZHEN HUBSAN TECHNOLOGY CO., LTD
Address of Applicant: Unit 2801-2802A, Building F, Xinghe WORLD , Yabao Road, Bantian Street,
Longgang District, Shenzhen,China.
Equipment Under Test (EUT):
EUT Name: HUBSAN HT018F Remote Control
Model No.: HT018F
Brand Name: HUBSAN
FCC ID: 2AN75-HT018F-1TX
Standards: 47 CFR Part 1.1307
47 CFR Part 1.1310
KDB447498D01 General RF Exposure Guidance v06
Date of Receipt: 2021-6-1

Date of Test: 2021-6-1 to 2021-7-6
Date of Issue: 2021-7-6
Test Result: PASS*
*In the configuration tested, the EUT complied with the standards specified above
Tested By：
(Lewis Zhou)
Reviewed By:
(Jun Li)
Approved By:
(Sheek Luo)
The test report is effective only with both signature and specialized stamp, The result(s) shown in this report refer only to the sample(s)
tested. Without written approval of CQA, this report can’t be reproduced except in full.
Shenzhen Huaxia Testing Technology Co., Ltd
1 Version
Revision History Of Report
Report No. Version Description Issue Date

CQASZ20210600783E-02 Rev.01 Initial report 2021-7-6
Page:2 of 6
2 Contents
Page
1 VERSION............................................................................................................................................................................. 2
2 CONTENTS......................................................................................................................................................................... 3
3 GENERAL INFORMATION.............................................................................................................................................. 4
3.1 CLIENT INFORMATION.................................................................................................................................................... 4
3.2 GENERAL DESCRIPTION OF EUT....................................................................................................................................4
4 RF EXPOSURE EVALUATION....................................................................................................................................... 5
4.1 RF EXPOSURE COMPLIANCE REQUIREMENT..................................................................................................................5
4.1.1 Standard Requirement...................................................................................................................................... 5
4.1.2 Limits.................................................................................................................................................................... 5
4.2 EUT RF EXPOSURE EVALUATION..................................................................................................................................6
Page:3 of 6
3 General Information
3.1 Client Information
Applicant: SHENZHEN HUBSAN TECHNOLOGY CO., LTD
Address of Applicant: Unit 2801-2802A, Building F, Xinghe WORLD , Yabao Road,
Bantian Street, Longgang District, Shenzhen,China.
Manufacturer: SHENZHEN HUBSAN TECHNOLOGY CO., LTD
Address of Manufacturer: Unit 2801-2802A, Building F, Xinghe WORLD , Yabao Road,
Bantian Street, Longgang District, Shenzhen,China.
Factory: Dongguan Tengsheng Industrial Co., Ltd.
Address of Factory: A22# Luyi Street, Tianxin Village, Tangxia Town, Dongguan, China.
3.2 General Description of EUT

Product Name: HUBSAN HT018F Remote Control
Model No.: HT018F
Trade Mark: HUBSAN
Hardware Version: V1.0
Software Version: V1.0
Frequency Range: 2405MHz ~ 2475MHz
Modulation Type: OFDM
Number of Channels: 36(declared by the client)
Sample Type: Mobile Portable Fix Location
Test Software of EUT: RF test
Antenna Type: PCB antenna
Antenna Gain: 2dBi
Power Supply: Battery: 3.6V 4400mAh Li-Po 15.84Wh
Page:4 of 6
4 RF Exposure Evaluation
4.1 RF Exposure Compliance Requirement
4.1.1 Standard Requirement
According to KDB447498D01 General RF Exposure Guidance v06
4.3.1. Standalone SAR test exclusion considerations
Unless specifically required by the published RF exposure KDB procedures, standalone 1-g
head or body and 10-g extremity SAR evaluation for general population exposure conditions, by
measurement or numerical simulation, is not required when the corresponding SAR Exclusion
Threshold condition, listed below, is satisfied.
4.1.2 Limits
The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances
≤ 50 mm are determined by:
[(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] ·
[√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR, where
f(GHz) is the RF channel transmit frequency in GHz

Power and distance are rounded to the nearest mW and mm before calculation17
The result is rounded to one decimal place for comparison
The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and
for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation
distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion
Page:5 of 6
4.2 EUT RF Exposure Evaluation
1) For 2.4G
eirp = pt x gt = (E x d)2/30
where:
pt = transmitter output power in watts,
gt = numeric gain of the transmitting antenna (unitless),
E = electric field strength in V/m, ---10((dBμV/m)/20)/106 ,
d = measurement distance in meters (m)---3m,
So pt = (E x d)2/30 / gt
The worst case (refer to report CQASZ20210600780E-01) is below:
Antenna polarization: Horizontal

Frequency (MHz) Level (dBuV/m) Polarization
2475 90.87 Peak
2475 86.85 Average
For 2475MHz wireless:

Field strength = 90.87dBμV/m @3m
Ant. gain 0dBi; so Ant numeric gain=1.0
So pt={[10(90.87/20)/106x3]2/30 /1.0}x1000mW =0.367mW
So (0.367mW/5mm)x √2.475GHz = 0.115,
0.115<3.0 for 1-g SAR
So the SAR report is not required.
Page:6 of 6

RF Exposure Evaluation Report: Shenzhen Huaxia Testing Technology Co., LTD

Uploaded by

Copyright:

Available Formats

RF Exposure Evaluation Report: Shenzhen Huaxia Testing Technology Co., LTD

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

RF Exposure Evaluation Report: Shenzhen Huaxia Testing Technology Co., LTD

Uploaded by

Copyright:

Available Formats

Shenzhen Huaxia Testing Technology Co.

RF Exposure Evaluation Report

Date of Receipt: 2021-6-1

Report No. Version Description Issue Date

3.2 General Description of EUT

f(GHz) is the RF channel transmit frequency in GHz

4.2 EUT RF Exposure Evaluation

The worst case (refer to report CQASZ20210600780E-01) is below:

Antenna polarization: Horizontal

For 2475MHz wireless:

0.115<3.0 for 1-g SAR

So the SAR report is not required.

You might also like