Project Documentation | UMRR Serial Relay Option Data Sheet

Project Number:

SMS Project Number:

Project Title:
Traffic Management Sensor

Keyword(s):
UMRR Serial Relay Option Data Sheet

Date:
August 16, 2019

Document:
UMRR Serial Relay Option Data Sheet.doc

Document state:
In progress
Ready for review
X Released
Outdated

PROPRIETARY
The information contained in this document may be subject to change without notice.
The information contained in this document shall remain the sole exclusive property of s.m.s smart microwave sensors GmbH.

UMRR Serial Relay Option Data Sheet.doc I Page 1 of 12 I August 16, 2019 www.smartmicro.de
1 User Safety Warning Information

Read the instructions carefully before you start to work.

Installation
Please observe the following advices when installing and connecting the sensors:
- Only use provided or approved equipment for installation. Use screws with metric
thread M3x8.
- Only skilled and instructed persons shall install and connect the devices. Proper
experience in working with mains voltage, electrical and electronic devices is required.
- Don’t wire any connections while power is applied to the device.
- Ground the devices carefully to prevent electrical shock.
- All connectors are pin-coded and fit in only one position. Also note the arrows
indicating the top side of sensor and SRO.
- After the SRO is connected to the sensor, don’t turn or twist the SRO until all screws
are tightened as this may damage the connector.
- Only use fully functional equipment (ladders, aerial work platform, …) when working
above ground. Staff shall be capable of working at heights.
- Use caution when installing the device on or around active roadways. Pay attention to
moving traffic.
- Mount the devices carefully to prevent them from shifting or dropping.
- Make sure that your installation methods are in accordance with local safety policy and
procedures and company practices.

Technical service
Only use provided or approved equipment for operation.
Persons other than authorized and approved electrical technicians shall NOT attempt to
connect this unit to a power supply, Traffic Management Interface Board and/or other
controllers, as there is a risk of electrical shock by unsafe handling of the power source.
Do not attempt to service or repair this unit.
- No user-maintainable parts are contained within the device.
- To avoid electrical shock, do not remove or open the cover.
- Unauthorized opening will void all warranties.
- Smartmicro is not liable for any damages or harms caused by unauthorized attempts
to open or repair the device.

Operation
Using SRO does not influence sensor performance.
Do not operate the device if the device itself or any cables are damaged. The sensors are
designed to work under different environment conditions (temperature, rain, dust, …).
Regular maintenance such as cleaning or recalibration is not required.

PROPRIETARY
The information contained in this document may be subject to change without notice.
The information contained in this document shall remain the sole exclusive property of s.m.s smart microwave sensors GmbH.

UMRR Serial Relay Option Data Sheet.doc I Page 2 of 12 I August 16, 2019 www.smartmicro.de
2 Serial Relay Interface Option for UMRR-0A
The standard UMRR sensor (CAN or RS485 communication interface) can be extended with
the here described additional hardware module that adds 8 hardware relays.

With the Relays Option Module you can implement your applications without the need of an
additional controller unit.

Figure 1: SRO-00xxxx Module mounted to an UMRR Sensor (rear side)

Features:
• no influence on the UMRR sensor performance
• no additional controller needed
• 8 configurable solid state relays
• Relays as normally-open (NO) or normally-closed (NC) contacts available

PROPRIETARY
The information contained in this document may be subject to change without notice.
The information contained in this document shall remain the sole exclusive property of s.m.s smart microwave sensors GmbH.

UMRR Serial Relay Option Data Sheet.doc I Page 3 of 12 I August 16, 2019 www.smartmicro.de
Table 1: Environmental and Mechanical Data (SRO-00xxxx)

Parameter Value Unit

Ambient Temperature -40 ... +85 degree C
Relay Voltage Band -36V ... +36 V
Max.Switching Current 1000I mA
IP 67
Weight 122II g
Dimensions see Figure 2
Housing Identification SRO-000000/SRO-000100
Connector 24 Pin Connector (Binder Series 423)
I
Load Current at 25°C and a switching cycle of 1 second
II
Additional Weight to the UMRR Sensor

2.1.1 Module Dimensions

All values given in mm.

Figure 2: SRO-00xxxx Module Dimensions

PROPRIETARY
The information contained in this document may be subject to change without notice.
The information contained in this document shall remain the sole exclusive property of s.m.s smart microwave sensors GmbH.

UMRR Serial Relay Option Data Sheet.doc I Page 4 of 12 I August 16, 2019 www.smartmicro.de
2.1.2 Connector
The used sensor connector is a 24-pin male (plug) circular connector (water proof IP67,
series 423, manufacturer Binder GmbH, Germany). A female counterpart (socket) has to be
used to connect to the sensor. The pin numbering of the socket is shown in Figure 3, the pin
description is given in Table 2.

Figure 3: View on solder cup side of socket (rear view of female counterpart to be connected to sensor)

Table 2: SRO Sensor Connector pin out

Pin Function Wire color

1 Relay 6 In black
2 Relay 6 Out violet
3 Relay 7 In white/blue
4 Relay 7 Out brown/blue
5 CAN_L yellow
6 RS_485_LI pink
7 Relay 5 Out grey/pink
8 Relay 5 In red/blue
9 RS_485_HI grey
10 GND blue
11 CAN_H green
12 Relay 8 In white/green
13 Relay 8 Out brown/green
14 Vcc red
15 GND white
16 Relay 2 Out white/yellow
17 Relay 2 In yellow/brown
18 Relay 1 In white/pink
19 Vcc brown
20 Relay 3 Out grey/brown
21 Relay 3 In white/grey
22 Relay 4 In white/red
23 Relay 4 Out brown/red
24 Relay 1 Out pink/brown
I
RS_485 communication is only available for UMRR-0A
PROPRIETARY
The information contained in this document may be subject to change without notice.
The information contained in this document shall remain the sole exclusive property of s.m.s smart microwave sensors GmbH.

UMRR Serial Relay Option Data Sheet.doc I Page 5 of 12 I August 16, 2019 www.smartmicro.de
3 Serial Relay Interface Option for UMRR-11 & UMRR-0C
The Sensor Relay Option (SRO) is an add-on module to the standard UMRR. It can be
attached to the back of the sensor. The SRO offers 8 hardware relays and surge
protection in addition to the UMRR’s CAN or RS485 or Ethernet communication interface.

With the Sensor Relay Option, you can implement your relay-based applications without the
need of an additional controller unit.

Figure 4: SRO-01xxxx Module mounted to an UMRR Sensor (rear side)

Features:
• Works with standard UMRR-11 and UMRR-0C sensors1
• No additional controller needed
• 8 configurable solid state relays, normally closed (NC)2
• Provides an easy-to-use universal electrical interface through a terminal block.
• Field installable. Just insert cable, tighten and tighten the four captive screws.
• Surge Protection on power, communication and relay lines
• Robust: The SRO-01xxxx is watertight and almost unbreakable.
• Integrates into smartmicro’s BRACKETs.

1
UMRR-11 is supported for units delivered starting May 2018
2
Normally Open available on request.
PROPRIETARY
The information contained in this document may be subject to change without notice.
The information contained in this document shall remain the sole exclusive property of s.m.s smart microwave sensors GmbH.

UMRR Serial Relay Option Data Sheet.doc I Page 6 of 12 I August 16, 2019 www.smartmicro.de
Table 3: Environmental and Mechanical Data (SRO-01xxxx)

Mode No. SRO-0110xx / SRO-0111xx

Mechanical
Weight 205II g, excluding cable.
Height 79.8 mm excluding cable outlet
ca. 116 mm including cable outlet
Width 84 mm
Depth 29 mm
Supported Cables
Supported cable diameter 9 mm – 13 mm
(smaller diameter available on request)
Supported conductor cross 0.25 mm2 – 0.75 mm2
section range AWG24 - AWG20
Surge Protection
Surge protection of power lines Compliant to IEC 61000-4-2 (ESD) and
IEC 61000-4-4 (fast transients)
Surge protection of data lines Compliant to IEC 61000-4-2 (ESD) and
and relay channels IEC 61000-4-4 (fast transients)
Relay Channels
Relay Voltage Band -36V ... +36V
Max. Switching Current 1000mAI
Other
Ambient Temperature -40°C ... +85°C
IP 67
I
Load Current at 25°C and a switching cycle of 1 second
II
Additional Weight to the UMRR Sensor

PROPRIETARY
The information contained in this document may be subject to change without notice.
The information contained in this document shall remain the sole exclusive property of s.m.s smart microwave sensors GmbH.

UMRR Serial Relay Option Data Sheet.doc I Page 7 of 12 I August 16, 2019 www.smartmicro.de
3.1 Pinout
The pinout is printed on the SRO board. The signal names in the upper right directly
correspond to the terminal blocks in the lower left.
Example: the yellow boxes in Figure 5 indicate the terminal block for “CAN High“ signal.

Figure 5: SRO-01xxxx pinout and jumpers

PROPRIETARY
The information contained in this document may be subject to change without notice.
The information contained in this document shall remain the sole exclusive property of s.m.s smart microwave sensors GmbH.

UMRR Serial Relay Option Data Sheet.doc I Page 8 of 12 I August 16, 2019 www.smartmicro.de
3.2 Variants
See Table 4 for a list of SRO-01xxxx variants and the sensor types they support.

Note: the variant can be changed by the user by rotation of the PCB inside the housing by
180 degrees.

SRO variant Supported UMRR

SRO-011000 UMRR-11 Type 44
UMRR-11 Type 45
SRO-011100 UMRR-0C Type 40
UMRR-0C Type 42
Table 4: Junction Box variants

3.3 Dip Switches

Refer to Figure 5 to find the 2 blue marked dip switches.

The two dip switches are bridges between pins 3 and 5 / pins 4 and 6 of the terminal block.
Those bridges must be open for full duplex RS485 operation and must be closed for
half-duplex RS485.

Please note dip switches are set for full duplex RS485 as delivered. Change the
switches to “half duplex” for half-duplex RS485 operation.

PROPRIETARY
The information contained in this document may be subject to change without notice.
The information contained in this document shall remain the sole exclusive property of s.m.s smart microwave sensors GmbH.

UMRR Serial Relay Option Data Sheet.doc I Page 9 of 12 I August 16, 2019 www.smartmicro.de
4 Field Cable for SRO and SRO2

Smartmicro approved unique cable type of Medikabel, manufacturer part no. 9DB281231C01
for use with SRO and SRO2. For more details please contact [email protected].

PROPRIETARY
The information contained in this document may be subject to change without notice.
The information contained in this document shall remain the sole exclusive property of s.m.s smart microwave sensors GmbH.

UMRR Serial Relay Option Data Sheet.doc I Page 10 of 12 I August 16, 2019 www.smartmicro.de
5 Important Legal Disclaimer Notice
All Product, Product specifications and data in this project documentation are subject to change without notice to improve reliability, function,
design or otherwise.

The statements, technical information and recommendations contained herein are believed to be accurate as of the date hereof. Smartmicro
disclaims any and all liability for any errors, inaccuracies or incompleteness contained in this datasheet or in any other disclosure relating to
the Product.

To the extent permitted by applicable law, Smartmicro disclaims (i) any and all liability arising out of the application or use of the Product or
the data contained herein, (ii) any and all liability of damages exceeding direct damages, including - without limitation – indirect,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of suitability of the Product for a particular
purpose.

Statements regarding the suitability of Products for certain types of applications are based on Smartmicro’ knowledge of typical
requirements that are often placed on Smartmicro’ Products in generic/general applications. Such statements are, however, not binding
statements about the suitability of Products for a particular/specific application. It is the customer/user’s own responsibility to validate that
the Product with the specifications described herein is suitable for use in its particular/specific application. Parameters and performance of
the Products may due to particular/specific applications and due to particular/specific surroundings deviate from the statements made
herein. Therefore, it is important that customer/user has thoroughly tested the Products and has understood the performance and the
limitations of the Products before installing the Products for the final applications or before commercialization. Although Products are well
optimized to be used for the intended applications stated herein, it must also be understood by the customer/user that the detection
probability may not be 100 % and the false alarm rate may not be zero.

The information provided herein, relates only to the specific Product designated and may not be applicable when such Product is used in
combination with other materials or in any process not defined herein. All operating parameters, including typical parameters, must be
validated for each customer application by the customer/user’s technical experts. Customers using or selling Smartmicro products not
expressly indicated for use in such applications do so at their own risk.

This Product specification or data sheet does not expand or otherwise modify Smartmicro terms and conditions of purchase, including but
not limited to the warranty expressed therein.

Except as expressly indicated in writing by Smartmicro, the Products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Product could result in personal injury or death.

No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of
Smartmicro Product names and markings noted herein may be trademarks of their respective owners.

Please note that the application of the Product may be subject to standards or other regulations that may vary from country to country.
Smartmicro does not guarantee that the use of Products in the applications described herein will comply with such regulations in any
country. It is the customer/user’s responsibility to ensure that the use and incorporation of Products complies with the regulatory
requirements of their markets.

If any provision of this Disclaimer is, or is found to be, void or unenforceable under applicable law, that will not affect the validity or
enforceability of the other provisions of this Disclaimer.

PROPRIETARY
The information contained in this document may be subject to change without notice.
The information contained in this document shall remain the sole exclusive property of s.m.s smart microwave sensors GmbH.

UMRR Serial Relay Option Data Sheet.doc I Page 11 of 12 I August 16, 2019 www.smartmicro.de
6 Contact

Address:

smart microwave sensors GmbH

In den Waashainen 1
38108 Braunschweig
Germany

Phone / Fax numbers:

Phone: +49-531-39023-0
Fax: +49-531-39023-599

Web / Email address:

Web: www.smartmicro.de
Email: [email protected]

PROPRIETARY
The information contained in this document may be subject to change without notice.
The information contained in this document shall remain the sole exclusive property of s.m.s smart microwave sensors GmbH.

UMRR Serial Relay Option Data Sheet.doc I Page 12 of 12 I August 16, 2019 www.smartmicro.de